Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 144/287 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• Wake-on-lan only works so many times

  - by Chance

  I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

  Read the article

• Qnap won't connect to Windows Share

  - by thetrashcan

  I have a qnap nmp-1000 in my network and would like to stream my films from my win7 laptop to the nmap-1000 device. I just managed to do so with upnp sharing, but I would like to, for security reasons, share my files over a shared folder which is password protected. My problem is when I'm searching for devices on my network with the qnap then it won't find any. When I try to mount a remote disk on my qnap it will just fail with an connection failed message. But when I try to connect to the qnap device with my laptop, it does this succesfully. Can someone guide me through on how to get my setup working?

  Read the article

• Is it better to use N WiFi or Cat5e ethernet for large file transfers?

  - by Seth

  I have a network containing 802.11 N WiFi Devices and gigabit ethernet devices, however using only Cat5e wiring. I know that if I used Cat6, the ethernet would be much faster however if I need to transfer a large file between a device thats connected normally connected via ethernet and a device thats normally connected via WiFi, would it be advantageous to bother plugging the WiFi device in to the network? or should I switch the ethernet device to WiFi? or does it really matter?

  Read the article

• Loss of wireless network connectivity when playing video via HDMI cable

  - by Jeff Fohl

  Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas? EDIT: I am now leaning towards the possibility that the HDMI cable is somehow interfering with the wireless network, when large amounts of data are being pushed through the cable. Is this possible?

  Read the article

• Connecting switch to switch to router

  - by elated

  Hello, Not sure if this is the right place to ask this question. But I have a router which connects to the internet. Now I have a switch connected to this router. I added a lot more computers so I added another switch and connected it to the first switch using a cross-over cable. As soon as I connect it to the first switch, my lights in first switch start blinking like crazy and my entire network simply stops working. The minute I remove the second switch's wire, its all fine again. What could be the problem?

  Read the article

• How do I network this Windows Failover Cluster and MongoDB Replica Set? (diagram inside)

  - by arex1337

  As you can see, my two Windows Server Failover Cluster (WSFC) nodes have three network interfaces each, which connects them to three different networks : A public network A private network consisting of the WSFC nodes A private network consisting of the WSFC nodes and a machine with the WSFC Quorum Witness File Share Does this network configuration I've planned, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. My two MongoDB Replica Set nodes also have three network interfaces each - very similar to the previous situation: A public network A private network consisting of the primary and secondary MongoDB Replica Set nodes A private network consisting of the primary, secondary and arbiter MongoDB Replica Set nodes Does this network configuration, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. Here is the simpler version I'm considering: UPDATE:

  Read the article

• Slackware - Assigning routes (IP address ranges) to one of many network adapters

  - by Dogbert

  I am using a Slackware 13.37 virtual machine within VirtualBox (current). I currently have a number of Ubuntu VMs on a single server, along with this Slackware VM. All VMs have been set up to use "Internal Network" mode, so they are all on a private LAN, and can see each other (ie: share files amongst themselves), but they remain private from the outside world. On on the these VMs (the Slackware one), I need to be able to grant it access to both this private network, and the internet at large. The first suggestion I found for handling this is to add another virtual network adapter to the VM, then set it to NAT. This results in the Slackware VM having the following network adapter setup: -NIC#1: Internal Network -NIC#2: NAT I want to set up the first network adapter (NIC#1) to handle all traffic on the following subnets: 10.10.0.0/255.255.0.0 192.168.1.0/255.255.255.0 And I want the second virtual network adapter (NIC#2) to handle everything else (ie: internet access). May I please have some assistance in setting this up on my Slackware VM? Additionally, I have searched for similar questions on SuperUser and Stackoverflow, but they all seem to pertain to my situation (ie: they all refer to OSX, or Ubuntu via the use of some UI-based tool). I'm trying to do this on Slack specifically via the command-line. Thanks!

  Read the article

• Open ports for Apache Tomcat-7.0.32 on Linux Mandriva

  - by ivanov-void

  I installed Apache Tomcat-7.0.32 on Linux Mandriva and I want to make it accessible. for this I need to open ports in iptables. I added the following rules- iptables -A INPUT -p tcp -m tcp --dport 8081 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8010 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8444 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8006 --syn -j ACCEPT then save and restart iptables - /etc/init.d/iptables save /etc/init.d/iptables restart verify, that ports is open - netstat -tulpn | less I am running command - netstat-ntpl | grep java and see - When I disable the firewall, I see the start page of the server on request - http://server_ip:8081/ When enable - server not accessible from outside. In what may be the cause? I would be most grateful for the information! Thank you!

  Read the article

• Flow of packet in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN. When packet goes from router to local LAN, do it passes all the computers? Means did it goes to ehernet card of every computer and those computers accept the packet based on their physical address. To which pc the packet will go first? To the nearest to the router? What happen if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this? Thanks in advance.

  Read the article

• Postfix as mail relay for web servers?

  - by Ben Carleton

  Hi all, I want to set up Postfix to relay mail from a group of webservers. I would like to limit senders by IP so I can restrict the box to only my webservers, so I don't have an open relay and don't have to worry about authentication. So, what I guess I need is to limit inbound access but allow mail to be sent to any outbound address. I've looked through the docs and don't even know where to start, so any tips would be appreciated. Thanks!

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• How do ISPs/Colocation Facilities limit bandwidth for Ethernet Drops?

  - by Kyle Brandt

  I have switch providers and have run into some problems with bandwidth limitations. I have more bandwidth then before, but there are performance issues. The router is connected to a 100mBit port, but they limit it to arbitrary settings (in software I imagine). It seems when I go above the limit, the provider starts to drop packets beyond the limit (This is what they said they do as well). Is it possible the previous provider did something like queuing packets above the this limit before dropping them? Is anyone aware of not only what can be done, but what is typical? Also, is there anything I can do on my Cisco router to help this situation? It would seem I am pretty helpless if the packets are dropped before they reach my interface (The traffic that is high is inbound to my network).

  Read the article

• Arch Linux: eth0 no carrier - network fails at boot

  - by user905686

  The problem My computer is connected to a network where dhcp is required. So my network configuration in /etc/rc.conf looks like interface=eth0 address= netmask= broadcast= gateway= My deamons are DAEMONS=(!hwclock syslog-ng network netfs crond ntpd) With this configuration, Arch hangs at boot a long time at "Network" (Still it says "[done]", but after boot I have no connection). I found out two workaround: Workaround 1 remove network from deamons run mii-tool --reset eth0 and dhcpcd eth0 after boot (somehow it does not work when placing these commands in /etc/rc.local. Then dhcp work very quickly (because of the reset!). Before executing the first command, ip link show eth0 has "NO CARRIER" in output. Afterwards, it doesn´t. (Also, mii-tool first shows "no link", afterwards eth0: 10 Mbit, half duplex, link ok. Workaround 2 Change network configuration to interface=eth0 address=x.y.z.21 netmask=255.255.255.0 broadcast=xxx.y.z.255 gateway=x.y.z.254 whereas x, y, z build the specific adresses of the network (Though dhcp is used, I get a static ip). Add the commands mii-tool --reset eth0 and dhcpcd eth0 to /etc/rc.local Now network starts quickly at boot (though I don´t know if successfully), the commands in /etc/rc.local are executed and the connection is fine after login. What to do? So the problem seems to be that dhcpcd stucks at "wating for carrier" or sth. I do not like the workaround, because some deamons need network (though they seem to start). What can I do to have eth0 ready for dhcp at boot? Or is there another problem?

  Read the article

• Sending a UDP message to a computer inside a network

  - by Dan

  Say I have the ip and mac address of a computer inside a network and I wish to send him a UDP message. By initializing the mac and ip addresses of the sent message to the given, when the network router recives the message he should pass it to the computer with the same mac address...right? Im asking becuase a program I write dosent seem to handle this limitation. it works great when its on the same network, but otherwise ...nada. Thanks

  Read the article

• Laptops trying to connect via wireless? Only able to connect only via wired connection

  - by Chris J. Lee

  It seems that all the wireless laptops in the office have disconnected and are unable to reconnect to the wifi after a terrible storm caused some power interruptions. Troubleshooting actions Verify wireless broadcasting is up With each laptop i ended up flushing their dns cache on Win 7 (ipconfig /flush ) Performed an ipconfig /all to see what the new ip is Made sure password was correct Reset the router (multiple times) restarted each laptop. Tried connecting wirelessly Am i missing some small detail ? Network information The router is a linksys/cisco WRVS4400N router. Supports a lot of fancy features i don't know how to use. We have 3 static ip's the conference room computer, the wireless printer, my computer Mostly windows machines, we have 3 mac users

  Read the article

• Can I use an Apple AirPort Express as a wireless-to-wired bridge?

  - by Chris

  I have a wireless network using an Apple AirPort Extreme. That device is set up in my office and hooked up to the cable modem. I have a TV in another room which can accept a wired internet connection (not wireless enabled). Can I use an Apple AirPort Express's ethernet jack to create a wireless-to-wired bridge? If not, what device would I use to do the same thing?

  Read the article

• Finding a private (NAT) host's IP using historic destination data

  - by l0c0b0x

  The issue: An unknown private (NAT) client is infected with malware and it's trying to access a Bot server at random times/dates. How we know about this: We receive bot traffic notices/alerts from REN-ISAC. Unfortunately, we don't receive those until the next day after it has happened. What they provide to us is: The source address (of the firewall) The destination addresses (it varies, but they're going to network subnet allocated to a German ISP) The source port (which varies--dynamic ports). Question: What would be the best approach to finding this internal host (historically) with a Cisco ASA as firewall? I'm guessing blocking anything to the destination address(es), and logging that type of traffic/access might allow me to find the source host, but I'm not sure which tool/command would be the most useful. I've seen Netflow thrown into a few responses when it comes to logging, but I'm confused with it's association of Logging, NAL, and nBAR, and how they relate to Netflow.

  Read the article

• How do I create a bridged virtual network for libvirt+KVM+ubuntu-server the easy way?

  - by Arthur Ulfeldt

  I see lots of documentation on how to manually set up a network bridge and then manually add vm's tun devices to these bridges and then write a shell script that glues it all together. lots of work, very manual, and not impressive. On the other hand if you want to use NAT to KVM+libvirt VMs to the network you just click the new network button in the virt-manager gui and relax. Am I missing "the easy way" of causing a VM to share the physical network with the host?

  Read the article

• Find slow network nodes between two data centers

  - by 2called-chaos

  I've got a problem with syncing big amount of data between two data centers. Both machines have got a gigabit connection and are not fully occupied but the fastest that I am able to get is something between 6 and 10 Mbit = not acceptable! Yesterday I made some traceroute which indicates huge load on a LEVEL3 router but the problem exists for weeks now and the high response time is gone (20ms instead of 300ms). How can I trace this to find the actual slow node? Thought about a traceroute with bigger packages but will this work? In addition this problem might not be related to one of our servers as there are much higher transmission rates to other servers or clients. Actually office = server is faster than server <= server! Any idea is appreciated ;) Update We actually use rsync over ssh to copy the files. As encryption tends to have more bottlenecks I tried a HTTP request but unfortunately it is just as slow. We have a SLA with one of the data centers. They said they already tried to change the routing because they say this is related to a cheap network where the traffic gets routed through. It is true that it will route through a "cheapnet" but only the other way around. Our direction goes through LEVEL3 and the other way goes through lambdanet (which they said is not a good network). If I got it right (I'm a network intermediate) they simulated a longer path to force routing through LEVEL3 and they announce LEVEL3 in the AS path. I basically want to know if they're right or they're just trying to abdicate their responsibility. The thing is that the problem exists in both directions (while different routes), so I think it is in the responsibility of our hoster. And honestly, I don't believe that there is a DC2DC connection which only can handle 600kb/s - 1,5 MB/s for weeks! The question is how to detect WHERE this bottleneck is

  Read the article

• What is automatic service location on the network?

  - by Roman

  I know that zeroconf does automatic service location on the local network. But what does it mean? For example there is a printer (printing is the service that it does). This printer choose randomly an IP for itself. It asks other devices if this IP is already occupied. If not, the printer occupies this IP. Then printer says to "everybody" that "printing" service is associated with this IP. Is it "automatic service location"? Or I got something wrong?

  Read the article

• Why would http & https be blocked, even in safe mode with firewall disabled?

  - by Cogwheel

  I have a windows 7 machine (dell studio xps). Everything on it seems to be in working order. The network device says it has internet connectivity, and indeed I can ping websites, transfer files via ftp, connect to vpns and remote desktop, but the web won't work. I've disabled the windows firewall and still no go. There are no other firewalls installed. The computer came with a trial of norton 360 so I also used the norton removal tool (which solved a similar problem on another computer for me previously). Any thoughts?

  Read the article

• Isolating a computer in the network

  - by Karma Soone

  I've got a small network and want to isolate one of the computers from the whole network. My Network: <----> Trusted PC 1 ADSL Router --> Netgear dg834g <----> Trusted PC 2 <----> Untrusted PC I want to isolate this untrusted PC in the network. That means the network should be secure against : * ARP Poisoning * Sniffing * Untrusted PC should not see / reach any other computers within the network but can go out the internet. Static DHCP and switch usage solves the problem of sniffing/ARP poisoning. I can enable IPSec between computers but the real problem is sniffing the traffic between the router and one of the trusted computers. Against getting a new IP address (second IP address from the same computer) I need a firewall with port security (I think) or I don't think my ADSL router supports that. To summarise I'm looking for a hardware firewall/router which can isolate one port from the rest of the network. Could you recommend such a hardware or can I easily accomplish that with my current network?

  Read the article

• Windows 8.1 killed my wifi

  - by char1es

  Was running Windows 8 on a Lenovo G780 and updated to windows 8.1 Wifi does not work anymore, i always receive a dns server not responding error. I have tried using public dns servers from Google but with still no results. I've restarted my router with no results. All other devices on my network are having no trouble at all. I've tried updating the wireless driver but the manufacturers website claims that the Win8.1 driver should be updated with the update from windows. So i cant find a wireless driver... Anyone else having this error and does anyone have any ideas on how to fix it?? EDIT: here are the driver details: Broadcom 802.11n Network Adapter Provider: Microsoft Driver Date: 2013-05-31 Driver Version: 6.30.223.102 Digital Signer: Microsoft Windows Thanks

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

• Image storage social network (Host plan)

  - by Samir

  I'm wondering what the best way is to host images on a social network site. Let's say that I expect my social network to reach 500.000 users in 2 years time. That would mean that if every user uploaded about 100 images and every image is 1 MB that I will have to need: 500.000 * 100 * 1 MB = 50.000.000 MB which means 50 terabytes. I'm not sure how I can best setup my hosting plan in order to have a solid bases to store my images and eventually store video files as well. Which hosting plan would you recommend me to start with and how can I enhance the plan?

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >