Search Results

Search found 38117 results on 1525 pages for 'sql tools'.

Page 1485/1525 | < Previous Page | 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492  | Next Page >

  • IP Micro-outages, telephone micro-outages, and CATV micro-outages

    - by Michael Graff
    This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

    Read the article

  • In what (small) ways can I modify Octave's compile options to enhance it without breaking it?

    - by irrational John
    If the title to this question seems a bit vague, I am sorry. But I wasn't sure how to distill what I am attempting to do into a single sentence. A few weeks back I learned that I could build and install recent releases of Octave on an Ubuntu 12.04 system by following the steps below. Install the tools needed to compile, link, and run octave. For Ubuntu the commands below have worked for me. sudo apt-get build-dep octave3.2 sudo apt-get install build-essential gnuplot gtk2-engines-pixbuf sudo apt-get install libfontconfig-dev bison Next, download the source code for an Octave release from the Gnu Project Archives for Octave and unpack the archive into a folder on your system. Use the commands below to build, check, and install octave. ./configure make make check sudo make install Unfortunately it turns out that the above builds an Octave that contains all the debugging symbol tables. The object files alone are huge taking up around 1.7 GB. The current Octave documentation suggests To compile without debugging symbols try the command make CFLAGS=-O CXXFLAGS=-O LDFLAGS= instead of just make. However, when I tried this it did not work. The -g option was still used for the compiles. For the heck of it I instead tried ./configure CFLAGS=-O CXXFLAGS=-O and this did work. (Instead of ~1.7GB the result of the build now takes up around 253MB). My questions are Is this actually the correct (recommended?) method to use to compile Octave without debugging symbols (i.e. without -g)? How would I compile Octave so it uses x86_64 rather than x86? Note: I am not asking how to compile Octave to use the (experimental) 64-bit integers for array dimensions. I just want to allow the compiler to use the extra registers and word sizes available when an app runs in 64-bit mode. Is a (more) complete list available for the directives used with the Octave Makefile? I have only seen make, make check, and make install documented. But apparently make distclean is also allowed. (It removes the compilation results so you can do a complete rebuild of everything.) I'm wondering what else might be available. FWIW, I have tried using ./configure CFLAGS="-O3 -mtune=core2 -m64" CXXFLAGS="-O3 -mtune=core2 -m64" and, surprisingly, it not only appeared to build, but also ran and passed the make check tests. The ./configure script even gave me the (deceptively?) reassuring message "Octave is now configured for x86_64-unknown-linux-gnu". But of course that's not the same thing as saying it actually "works". Is there a recommended way to enable Octave to run as an x86_64 app? I have also tried looking inside the Octave Makefile to see if I could decipher what command line directives it accepts. I got nowhere. I have not a single clue as to how that Makefile does whatever it is that it does.

    Read the article

  • recommendations for efficient offsite remote backup solution of vm's

    - by senorsmile
    I am looking for recommendations for backing up my current 6 vm's(and soon to grow to up to 20). Currently I am running a two node proxmox cluster(which is a debian base using kvm for virtualization with a custom web front end to administer). I have two nearly identical boxes with amd phenom II x4's and asus motherboards. Each has 4 500 GB sata2 hdd's, 1 for the os and other data for the proxmox install, and 3 using mdadm+drbd+lvm to share the 1.5 TB's of storage between the two machines. I mount lvm images to kvm for all of the virtual machines. I currently have the ability to do live transfer from one machine to the other, typically within seconds(it takes about 2 minutes on the largest vm running win2008 with m$ sql server). I am using proxmox's built-in vzdump utility to take snapshots of the vm's and store those on an external harddrive on the network. I then have jungledisk service (using rackspace) to sync the vzdump folder for remote offsite backup. This is all fine and dandy, but it's not very scalable. For one, the backups themselves can take up to a few hours every night. With jungledisk's block level incremental transfers, the sync only transfers a small portion of the data offsite, but that still takes at least a half an hour. The much better solution would of course be something that allows me to instantly take the difference of two time points (say what was written from 6am to 7am), zip it, then send that difference file to the backup server which would instantly transfer to the remote storage on rackspace. I have looked a little into zfs and it's ability to do send/receive. That coupled with a pipe of the data in bzip or something would seem perfect. However, it seems that implementing a nexenta server with zfs would essentially require at least one or two more dedicated storage servers to serve iSCSI block volumes (via zvol's???) to the proxmox servers. I would prefer to keep the setup as minimal as possible (i.e. NOT having separate storage servers) if at all possible. I have also briefly read about zumastor. It looks like it could also do what I want, but it appears to have halted development in 2008. So, zfs, zumastor or other?

    Read the article

  • Where should I go with hosting my site: VPS, GAE, another option?

    - by Jonathan Hayward
    My website, http://JonathansCorner.com/, began life before 1994 as www.imsa.edu/~jhayward/ and has been through various iterations and improvements to content, HTML, and the like, but remains a literature site that is from a web administrator's perspective fairly simple and primitive: a fair amount of static HTML and supporting files, a little bit of CGI and URI rewriting, .htaccess files providing Expires: headers and the like. An associated site demoes various CGI scripts that fall under the category of "and other creations"; the site as a whole has the purpose of sharing my creative works, and so far a fairly rudimentary use of Apache functionality, supported by Unix tools to, for instance, update RSS feed and the "starting point" link on the home page, has served that purpose fairly well. I looked around here on web hosting, and found the note on web host reccommendations as a good note for "What are some of people's favorite web hosts overall," but I wanted to ask a more focused question of "What are the best web hosts for criteria XYZ:" I am looking at a VPS so I will have root, be able to install stuff and edit Apache's config files etc., running Gentoo or other Linux, BSD, or the like. I would like a system that is secure enough that the host's vulnerabilities are mostly the ones that come along with what I am trying to do: that is, I won't be trying to administer and secure an ancient Linux like some have complained about at 1and1. I would like good uptime/reliability and competent support staff: if the level 1 help desk is going to tell me to go to "My Computer" on a Linux box, I'd like to be able to get past them. Ideally I would like a site hosted within some place that will have low latency for U.S. visitors in particular. I would like a hosting solution that will be with a stable business, one that will probably be around, and one unlikely to vanish without warning. With those things specified, I would be interested in knowing what are the less expensive options. (I expect that some of the things I've specified will knock out all of the cheapest options, but I'm still interested in price.) With all that stated, I'd like to back up a bit and look at whether I am asking the right question. I am concerned that the above is a very good way of asking, "How can I keep my site in line with the wave of the past?" I am wondering if it might be specifically wiser to look to adapt my site to newer technologies instead of trying to keep it on older technologies. For instance, while I would hardly portray my site as a way to show off the full power of Google App Engine, the main site at least should be a straightforward port if I were to do that. And beyond Google App Engine, my knowledge of cloud solutions is basic. If it is a better and more future-proof solution to port my site to another kind of solution, I would be interested in knowing where those future-proof solutions lie. So I would be interested in wisdom. If the question I asked in detail is still a good question to be asking, what would people suggest? Or if I should seriously consider porting my site to a newer basic option, what should I try there? Any thoughts would be appreciated.

    Read the article

  • Planning trunk capacity for multiple GbE switches

    - by wuckachucka
    Without measuring throughput (it's at the top of the list; this is just theoretical), I want to know the most standard method for trunking VLANs on multiple Gigabit (GbE) switches to a core Layer 3 GbE switch. Say you have three VLANs: VLAN10 (10.0.0.0/24) Servers: your typical Windows DC/file server, Exchange, and an Accounting/SQL server. VLAN20: (10.0.1.0/24) Sales: needs access to everything on VLAN10; doesn't need access to VLAN30 and vice-versa. VLAN20: (10.0.1.0/24) Support: needs access to everything on VLAN10; doesn't need access to VLAN20 and vice-versa. Here's how I think this should work in my head: Switch #1: Ports 2-20 are assigned to VLAN20; all the Sales workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #1. Switch #2: Ports 2-20 are assigned to VLAN30; all the Support workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #2. Core L3 switch: Ports 2-10 are assigned to VLAN10; all three servers are connected here. With a standard 10/100 x 24 switch, it'll usually come with one or two 1 GbE uplink ports; carrying over this logic to a 10/100/1000 x 24, the "optional" 10 GbE combo ports that most higher-end switches can get shouldn't really be an option. Keep in mind I haven't tested anything yet, I'm primarily moving in this direction for growth (don't want to buy 10/100 switches and have to replace those within a couple of years) and security (being able to control access between VLANs with L3 routing/packet filtering ACLs). Does this sound right? Do I really need the 10 GbE ports? It seems very non-standard and expensive, but it "feels" right when you think about 40 or 50 workstations trunking up to the L3 switch over 1 GbE standard ports. If say 20 workstations want to download a 10 GB image from the servers concurrently, wouldn't the trunk be the bottleneck? At least if the trunk was 10 GbE, you'd have 10x1GbE nodes being able to reach their theoretical max. What about switch stacking? Some of the D-Links I've been looking at have HDMI interfaces for stacking. As far as I know, stacking two switches creates one logical switch, but is this just for management I/O or does the switches use the (assuming it's HDMI 1.3) 10.2 Gbps for carrying data back and forth?

    Read the article

  • IIS/ASP.NET performance incident - Perfmon Current Annonymous Users going through roof but Requests/sec low

    - by Laurence
    Setup: ASP.NET 4.0 website on IIS 6.0 on Win 2003 64 bit, 8xCPUs, 16GB memory, separate SQL 2005 DB server. Had a serious slowdown today with any otherwise fairly well performing ASP.NET site. For a period of a couple of hours all page requests were taking a very long time to be served - e.g. 30-60s compared to usual 2s. The w3wp.exe's CPU and memory usage on the webserver was not much higher than normal. The application pool was not in the middle of recycling (and it hadn't recycled for several hours). Bottlenecks in the database were ruled out - no blocks occurring and query results were being returned quickly. I couldn't make any sense of it and set up the following Perfmon counters: Current Anonymous Users (for site in question) Get requests/sec (ditto) Requests/sec for the ASP.NET application running the site Get requests/sec was averaging 100-150. Requests/sec for ASP.NET was averaging 5-10. However Current Anonymous Users was around 200. And then as I was watching, the Current Anonymous Users began to climb steeply going up to about 500 within a few minutes. All this time Get requests/sec & Requests/sec for ASP.NET was if anything going down. I did a whole load of things (in a panic!) to try to get the site working, like shutting it down, recycling the app pool, and adding another worker process to the pool. I also extended the expiration time for content (in IIS under HTTP Headers) in an attempt to lower the number of requests for static files (there are a lot of images on the site). The site is now back to normal, and the counters are fairly steady and reading (added Current Connections counter): Current Anonymous Users : average 30 Get requests/sec : average 100 Requests/sec for ASP.NET : 5 Current Connections : average 300 I have also observed an inverse relationship between Get requests/sec & Current Anonymous Users. Usually both are fairly steady but there will be short periods when Get requests/sec will go down dramatically and Current Anonymous Users will go up in a perfect mirror image. Then they will flip back to their usual levels. So, my questions are: Thinking of the original performance issue - if w3wp.exe CPU, memory usage were normal and there was no DB bottleneck, what could explain page requests taking 20 times longer to be served than usual? What other counters should I be looking at if this happens again? What explains the inverse relationship between Get requests/sec & Current Anonymous Users? What could explain Current Anonymous Users going from 200 to 500 within a few minutes? Many thanks for any insight into this.

    Read the article

  • what is the best mid/high-end class audio/music creation audio sound card?

    - by Chris
    Hello, I have a computershop myself, and I repair computers. But one of the things I really don't know (yet) is the performace od audio cards for music creation with midi. I have searched and searched and came up with some good reviews, but after browsing for a couple of hours I could't see the trees trough the forrest :-D (it's a dutch expression) At one moment I thought the M-Audio - Delta 1010LT would be a good PCIe card, later on I read that this card was released years ago. (but that could be false information) Also any personal expierence would be great, but not necessairy. I have searched a few cards, and I hope someone can help me make a choice for a friend of mine. He's buget is between $100 and $350 I know there are audio cards from $ 500 - $1850,- this is just too expensive. The following specs are crucial: ASIO Midi Mic in minimal 5.1, 7.1 recommended it's not for airplay, but just to compose music at home. using Ableton and midi keyboard. 1. M-Audio - Delta 1010LT: 8 x 8 analog I/O 2 mic preamps or line inputs S/PDIF digital I/O (coaxial) with 2-channel PCM SCMS copy protection control digital I/O supports surround-encoded AC-3 and DTS pass-through 1 x 1 MIDI I/O directly drive up to 7.1 surround (bass management software included) software controlled 36-bit internal DSP digital mixing/routing +4dbu/-10dBV operation individually switched in software word clock I/O for sample accurate device synchronization 2. RME HDSP 9632: * Stereo Analog Ein- und Ausgang, symmetrisch*, 24-Bit/192kHz, > 110 dB SNR * Optionale Erweiterungsboards mit je 4 symmetrischen Ein- und Ausgängen * Alle analogen I/Os voll 192 kHz-fähig, also keine Reduzierung der Kanalzahl * 1 x ADAT Digital In/Out, 96 kHz-fähig (S/MUX) * 1 x SPDIF Digital In/Out, 192 kHz-fähig * 1 x Breakout Kabel für koaxialen SPDIF-Betrieb* * Also bis zu 16 Ein-und Ausgänge gleichzeitig nutzbar! * 1 x Stereo Kopfhörerausgang, parallel zum analogen Ausgang, aber eigene Pegelanpassung * 1 x MIDI I/O für 16 Kanäle Hi-Speed MIDI über Breakout Kabel * DIGICheck, RMEs einzigartiges Meter- und Analysetool mit Spectral Analyser, Professionelle Level Meter 2/8/16-Kanalig, Vector Audio Scope und diversen weiteren Analysefunktionen * HDSP Meter Bridge: Frei skalierbare Levelmeter mit Peak- und RMS Berechnung in Hardware * TotalMix: 512-Kanal Mischer mit 40 Bit interner Auflösung 3. EMU 1212M (1212 M) PCIe: * Top kwaliteit convertors 24-bit/192kHz convertors. * Hardware gestuurde effecten. * DSP zero-latency hardware mixen en monitoring. * Analoge en digitale I/O plus MIDI. * EMU Production Tools Software Bundle - Cakewalk SONAR , Steinberg Cubase LE, Ableton Live E-MU Edition **EMU 1212M PCI-e inputs/outputs:** * 2 balanced jack inputs. * 2 balanced jack outputs. * 24-bit/192kHz ADAT I/O. * 24-bit/192kHz Coaxiale S/PDif I/O switchable to AES/EBU. * MIDI I/O. 4. M-Audio Audiophile 192: - Up to 24-bit/192kHz audio - 2 balanced analog inputs (1/4” TRS) - 2 balanced analog outputs (1/4” TRS) - S/PDIF digital I/O (coaxial RCA connectors) with 2-channel PCM - SCMS copy protection control - Digital I/O supports surround-encoded AC-3 and DTS pass-through - Direct hardware input monitoring via separate balanced 1/4” TRS monitor outputs - Software routing of inputs and outputs - Digital I/O can be routed to/from external effects - 16-channel MIDI I/O - ASIO, WDM, GSIF 2 and Core Audio driver support for compatibility with most applications - 64-bit driver support for Windows - PCI 2.2 compatibility - Apple G5 compatible - Incompatible exceptions - Includes Ableton Live Lite music production software, so you can make music right away - Works with other Delta cards Technical Specifcations: - Compatibility - ASIO - WDM - GSIF 2 - Core Audio

    Read the article

  • "Error 1067: The process terminated unexpectedly" when trying to install MySQL on Win7 x64.

    - by Gravitas
    Hi, I've run into a brick wall trying to install MySQL v5.5 on my machine. My PC is Windows 7 x64, Enterprise edition. MySQL installs fine, but when I run the "MySQL Instance Configuration Wizard", it pauses forever on the step "Start Service" (I can let it run for 30 minutes with no response). If I go into services, I see that the "MySQL" service hasn't started, and if I try to start it, it says "Windows could not start MySQL Service on Local Computer. Error 1067: The process terminated unexpectedly." I've tried the following: Turning off firewall. Uninstalling all antivirus software. Installing / reinstalling 32-bit version of MySQL. Installing / reinstalling 64-bit version of MySQL. Uninstalling, deleting the contents of "C:\program files\MySQL" and "C:\program files (x86)\MySQL", reinstalling. Checking to see that there is no rogue services named MySQL???? (from a previous install). Checking that port 3306 is not used by an alternate program. Changing the default port that MySQL uses. Checking for "my.ini" and "my.ini.cnf" in "C:\windows" (nothing there but that can cause a problem). Running both MySQL installer, and configuration wizard, in "Adminstrator mode". Turning off UAC. Installing with defaults, not changing anything. Rebooting my machine (about 6 reboots so far). Opening up port 3306 in the firewall (both TCP and UDP, inbound and outbound). Swearing at the klutz of a programmer who designed MySQL so you can't even install it (as if that would help!) My machine is working 100% in every other way. InfiniDB (a MySQL compatible database) installs 100%, as does Visual Studio 2010, Microsoft SQL Server, etc, etc. Your advice on how to work around this? p.s. Here is the screen it got stuck on for 15 minutes until I killed the process: Update 2010-12-20 Tried MySQL v5.1, it didn't work either. Its amazing - if you type "mysqld /?", or "mysqld -help", it doesn't give you any help. And, if you try to restart the service manually, it doesn't display any error messages. Could it be any more unhelpful? Update 2010-12-21 Installed MySQL 6.0 alpha, and it worked. However, I'd rather not use an alpha release, given that the "stable" release is anything but :( Update 2010-12-21 Found http://dev.mysql.com/doc/refman/5.1/en/windows-troubleshooting.html, dealing with troubleshooting under Windows. Discovered that you can generate an error log if the service doesn't start - see here: http://dev.mysql.com/doc/refman/5.1/en/error-log.html

    Read the article

  • Installing chrome in Centos 6.2 (Final)

    - by usjes
    I need to install chrome in a dedicated centos server where I only access via ssh, it doesn't have X or any windows graphical stuff. I need it to be able to pack extensions using google-chrome --pack-extension. I tried adding this to /etc/yum.repos.d/google.repo [google-chrome] name=google-chrome - 32-bit baseurl=http://dl.google.com/linux/chrome/rpm/stable/i386 enabled=1 gpgcheck=1 gpgkey=https://dl-ssl.google.com/linux/linux_signing_key.pub And then yum install google-chrome-stable, but there's a huge list of dependencies problems: How can I install chrome without breaking anything else? UPDATE: Ok, I installed perl-CGI from .rpm because yum couldn't find it, now dependencies resolve and it show me this list of packages to install: Dependencies Resolved ============================================================================================================================================================================================================================================= Package Arch Version Repository Size ============================================================================================================================================================================================================================================= Installing: google-chrome-stable x86_64 19.0.1084.52-138391 google-chrome 35 M Installing for dependencies: ConsoleKit x86_64 0.4.1-3.el6 base 82 k ConsoleKit-libs x86_64 0.4.1-3.el6 base 17 k GConf2 x86_64 2.28.0-6.el6 base 964 k ORBit2 x86_64 2.14.17-3.1.el6 base 168 k bc x86_64 1.06.95-1.el6 base 110 k cdparanoia-libs x86_64 10.2-5.1.el6 base 47 k cups x86_64 1:1.4.2-44.el6_2.3 updates 2.3 M dbus x86_64 1:1.2.24-5.el6_1 base 207 k desktop-file-utils x86_64 0.15-9.el6 base 47 k ed x86_64 1.1-3.3.el6 base 72 k eggdbus x86_64 0.6-3.el6 base 91 k foomatic x86_64 4.0.4-1.el6_1.1 base 251 k foomatic-db noarch 4.0-7.20091126.el6 base 980 k foomatic-db-filesystem noarch 4.0-7.20091126.el6 base 4.4 k foomatic-db-ppds noarch 4.0-7.20091126.el6 base 19 M ghostscript x86_64 8.70-11.el6_2.6 updates 4.4 M ghostscript-fonts noarch 5.50-23.1.el6 base 751 k gstreamer x86_64 0.10.29-1.el6 base 764 k gstreamer-plugins-base x86_64 0.10.29-1.el6 base 942 k gstreamer-tools x86_64 0.10.29-1.el6 base 23 k iso-codes noarch 3.16-2.el6 base 2.4 M lcms-libs x86_64 1.19-1.el6 base 100 k libIDL x86_64 0.8.13-2.1.el6 base 83 k libXScrnSaver x86_64 1.2.0-1.el6 base 19 k libXfont x86_64 1.4.1-2.el6_1 base 128 k libXv x86_64 1.0.5-1.el6 base 21 k libfontenc x86_64 1.0.5-2.el6 base 24 k libgudev1 x86_64 147-2.40.el6 base 59 k libmng x86_64 1.0.10-4.1.el6 base 165 k libogg x86_64 2:1.1.4-2.1.el6 base 21 k liboil x86_64 0.3.16-4.1.el6 base 121 k libtheora x86_64 1:1.1.0-2.el6 base 129 k libvisual x86_64 0.4.0-9.1.el6 base 135 k libvorbis x86_64 1:1.2.3-4.el6_2.1 updates 168 k mailx x86_64 12.4-6.el6 base 234 k man x86_64 1.6f-29.el6 base 263 k mesa-libGLU x86_64 7.11-3.el6 base 201 k nvidia-graphics195.30-libs x86_64 195.30-120.el6 atrpms 13 M openjpeg-libs x86_64 1.3-7.el6 base 59 k pax x86_64 3.4-10.1.el6 base 69 k phonon-backend-gstreamer x86_64 1:4.6.2-20.el6 base 125 k polkit x86_64 0.96-2.el6_0.1 base 158 k poppler x86_64 0.12.4-3.el6_0.1 base 557 k poppler-data noarch 0.4.0-1.el6 base 2.2 M poppler-utils x86_64 0.12.4-3.el6_0.1 base 73 k portreserve x86_64 0.0.4-4.el6_1.1 base 22 k qt x86_64 1:4.6.2-20.el6 base 4.0 M qt-sqlite x86_64 1:4.6.2-20.el6 base 50 k qt-x11 x86_64 1:4.6.2-20.el6 base 12 M qt3 x86_64 3.3.8b-30.el6 base 3.5 M redhat-lsb x86_64 4.0-3.el6.centos base 24 k redhat-lsb-graphics x86_64 4.0-3.el6.centos base 12 k redhat-lsb-printing x86_64 4.0-3.el6.centos base 11 k sgml-common noarch 0.6.3-32.el6 base 43 k time x86_64 1.7-37.1.el6 base 26 k tmpwatch x86_64 2.9.16-4.el6 base 31 k xdg-utils noarch 1.0.2-17.20091016cvs.el6 base 58 k xml-common noarch 0.6.3-32.el6 base 9.5 k xorg-x11-font-utils x86_64 1:7.2-11.el6 base 75 k xz x86_64 4.999.9-0.3.beta.20091007git.el6 base 137 k xz-lzma-compat x86_64 4.999.9-0.3.beta.20091007git.el6 base 16 k Transaction Summary ============================================================================================================================================================================================================================================= Install 62 Package(s) Is it safe to continue and install all that or could I break something already installed?

    Read the article

  • configuration required for HIVE to be installed on a node

    - by ????? ????????
    I went through the process of manually installing ambari (not through SSH, because I couldnt get keyless to work) and everything installed OK, except for HIVE and GANGLIA. I got this message: stderr: None stdout: warning: Unrecognised escape sequence ‘\;’ in file /var/lib/ambari-agent/puppet/modules/hdp-hive/manifests/hive/service_check.pp at line 32 warning: Dynamic lookup of $configuration is deprecated. Support will be removed in Puppet 2.8. Use a fully-qualified variable name (e.g., $classname::variable) or parameterized classes. notice: /Stage[1]/Hdp::Snappy::Package/Hdp::Snappy::Package::Ln[32]/Hdp::Exec[hdp::snappy::package::ln 32]/Exec[hdp::snappy::package::ln 32]/returns: executed successfully notice: /Stage[2]/Hdp-hive::Hive::Service_check/File[/tmp/hiveserver2Smoke.sh]/ensure: defined content as ‘{md5}7f1d24221266a2330ec55ba620c015a9' notice: /Stage[2]/Hdp-hive::Hive::Service_check/File[/tmp/hiveserver2.sql]/ensure: defined content as ‘{md5}0c429dc9ae0867b5af74ef85b5530d84' notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/File[/tmp/hcatSmoke.sh]/ensure: defined content as ‘{md5}bae7742f7083db968cb6b2bd208874cb’ notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: 13/06/25 03:11:56 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. Make sure to provide a valid value for hive.metastore.uris if you are connecting to a remote metastore. notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: FAILED: SemanticException org.apache.hadoop.hive.ql.parse.SemanticException: org.apache.hadoop.hive.ql.metadata.HiveException: java.lang.RuntimeException: Unable to instantiate org.apache.hadoop.hive.metastore.HiveMetaStoreClient notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: 13/06/25 03:12:06 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. Make sure to provide a valid value for hive.metastore.uris if you are connecting to a remote metastore. notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: FAILED: SemanticException [Error 10001]: Table not found hcatsmokeida8c07401_date102513 notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: 13/06/25 03:12:15 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. Make sure to provide a valid value for hive.metastore.uris if you are connecting to a remote metastore. notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: FAILED: SemanticException o When i go to the alerts and health checks i’m getting this: ive Metastore status check CRIT for 42 minutes CRITICAL: Error accessing hive-metaserver status [13/06/25 03:44:06 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. What am I doing wrong? I have already tried to do ambari-server reset on the the database without results.

    Read the article

  • Bugzilla : No SASL mechanism found

    - by niteshsinha
    I am using Bugzilla on windows 7. I am using the unofficial Bugzilla installer. I followed the steps accordingly and gave valid credentials wherever required. I open Bugzilla and try to create a new account , but i get the following error. Software error: No SASL mechanism found at C:/Program Files/Bugzilla/perl/perl/site/lib/Authen/SASL.pm line 77 at C:/Program Files/Bugzilla/perl/perl/lib/Net/SMTP.pm line 143 i ran checksetup.pl and found that Authen::SASL and SMTP both are available on my machine. The output of checksetup.pl is as follows. * This is Bugzilla 3.6.3 on perl 5.10.1 * Running on Win7 Build 7600 Checking perl modules... Checking for CGI.pm (v3.33) ok: found v3.49 Checking for Digest-SHA (any) ok: found v5.48 Checking for TimeDate (v2.21) ok: found v2.24 Checking for DateTime (v0.28) ok: found v0.53 Checking for DateTime-TimeZone (v0.79) ok: found v1.10 Checking for DBI (v1.41) ok: found v1.609 Checking for Template-Toolkit (v2.22) ok: found v2.22 Checking for Email-Send (v2.16) ok: found v2.198 Checking for Email-MIME (v1.861) ok: found v1.903 Checking for Email-MIME-Encodings (v1.313) ok: found v1.313 Checking for Email-MIME-Modifier (v1.442) ok: found v1.903 Checking for URI (any) ok: found v1.52 Checking available perl DBD modules... Checking for DBD-Pg (v1.45) ok: found v2.16.1 Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for DBD-Oracle (v1.19) not found The following Perl modules are optional: Checking for GD (v1.20) ok: found v2.44 Checking for Chart (v2.1) ok: found v2.4.1 Checking for Template-GD (any) ok: found v1.56 Checking for GDTextUtil (any) ok: found v0.86 Checking for GDGraph (any) ok: found v1.44 Checking for XML-Twig (any) ok: found v3.34 Checking for MIME-tools (v5.406) ok: found v5.427 Checking for libwww-perl (any) ok: found v5.834 Checking for PatchReader (v0.9.4) ok: found v0.9.5 Checking for perl-ldap (any) ok: found v0.39 Checking for Authen-SASL (any) ok: found v2.15 Checking for RadiusPerl (any) ok: found v0.17 Checking for SOAP-Lite (v0.710.06) ok: found v0.710.10 Checking for JSON-RPC (any) ok: found v0.95 Checking for Test-Taint (any) ok: found v1.04 Checking for HTML-Parser (v3.40) ok: found v3.64 Checking for HTML-Scrubber (any) ok: found v0.08 Checking for Email-MIME-Attachment-Stripper (any) ok: found v1.316 Checking for Email-Reply (any) ok: found v1.202 Checking for TheSchwartz (any) not found Checking for Daemon-Generic (any) not found Checking for mod_perl (v1.999022) not found *********************************************************************** * OPTIONAL MODULES * *********************************************************************** * Certain Perl modules are not required by Bugzilla, but by * * installing the latest version you gain access to additional * * features. * * * * The optional modules you do not have installed are listed below, * * with the name of the feature they enable. Below that table are the * * commands to install each module. * *********************************************************************** * MODULE NAME * ENABLES FEATURE(S) * *********************************************************************** * TheSchwartz * Mail Queueing * * Daemon-Generic * Mail Queueing * * mod_perl * mod_perl * *********************************************************************** * Note For Windows Users * *********************************************************************** * In order to install the modules listed below, you first have to run * * the following command as an Administrator: * * * * ppm repo add theory58S http://cpan.uwinnipeg.ca/PPMPackages/10xx/ * * * Then you have to do (also as an Administrator): * * * * ppm repo up theory58S * * * * Do that last command over and over until you see "theory58S" at the * * top of the displayed list. * *********************************************************************** COMMANDS TO INSTALL OPTIONAL MODULES: TheSchwartz: ppm install TheSchwartz Daemon-Generic: ppm install Daemon-Generic mod_perl: ppm install mod_perl Reading ./localconfig... Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for MySQL (v4.1.2) ok: found v5.1.44-community-log Removing existing compiled templates... Precompiling templates...done. Now that you have installed Bugzilla, you should visit the 'Parameters' page (linked in the footer of the Administrator account) to ensure it is set up as you wish - this includes setting the 'urlbase' option to the correct URL. Press any key to continue . . . Please tell me what should i do. Please note: i am running behind a corporate proxy , SSL/TLS is not used internally but i am giving the smtpUser and smtpPass also.

    Read the article

  • MX records not correctly updated by the Google DNS servers

    - by Mac_Cain13
    We are currently losing some e-mail and we discovered that this is caused by a wrong DNS setting. We used a CNAME for our MX record an thats not allowed. So about 2 weeks ago we changed it to an A-record to fix the problem. It seems all major DNS services (like OpenDNS and ISPs) have synced their records and are returning correct results on our DNS queries. But Googles DNS service (at 8.8.8.8) is still returning the CNAME values and we still some e-mails are not delivered correctly. Query on OpenDNS: ; <<>> DiG 9.7.3-P3 <<>> mx wrep.nl @208.67.222.222 ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 51231 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;wrep.nl. IN MX ;; ANSWER SECTION: wrep.nl. 3595 IN MX 10 druif.wrep.nl. ;; Query time: 21 msec ;; SERVER: 208.67.222.222#53(208.67.222.222) ;; WHEN: Fri Nov 25 21:36:58 2011 ;; MSG SIZE rcvd: 47 Query on Google DNS: ; <<>> DiG 9.7.3-P3 <<>> mx wrep.nl @8.8.8.8 ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 12124 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 0 ;; QUESTION SECTION: ;wrep.nl. IN MX ;; ANSWER SECTION: wrep.nl. 2372 IN CNAME druif.wrep.nl. ;; AUTHORITY SECTION: wrep.nl. 572 IN SOA ns0.freshdns.nl. hostmaster.twilightinc.nl. 2011112401 14400 3600 604800 3600 ;; Query time: 94 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Fri Nov 25 21:38:10 2011 ;; MSG SIZE rcvd: 117 So is there anyone who can explain why Google is responding with a different (incorrect) result two weeks after the last change? And how can we get Google to update their DNS records correctly? Any help is very appreciated. (Please note that other domains that are managed by the same DNS servers/tools are working fine.)

    Read the article

  • My computer freezes irregurarly

    - by Manhim
    My computer started to freeze at irregular times for 3 weeks now. What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 50-60. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) My current to-try list Change the thermal paste on my CPU. Change my graphic card with a temporary one and stress the computer. Change my power supply. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

    Read the article

  • DNS with name.com and Amazon S3

    - by aledalgrande
    I have a website on a bucket in Amazon S3, and recently started to get emails from Google "Googlebot can't access your site". When I go to Webmaster Tools and I try to fetch in fact it doesn't work. Also people in locations different from mine sometimes reported they could not access the website. Now for curiosity I tried from my terminal: $ host xxx xxx is an alias for xxx.s3-website-us-west-1.amazonaws.com. xxx.s3-website-us-west-1.amazonaws.com is an alias for s3-website-us-west-1.amazonaws.com. s3-website-us-west-1.amazonaws.com has address yyy.yyy.yyy.yyy And when I try with dig: $ dig xxx ; <<>> DiG 9.8.3-P1 <<>> xxx ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 17860 ;; flags: qr rd ra; QUERY: 1, ANSWER: 3, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;xxx. IN A ;; ANSWER SECTION: xxx. 300 IN CNAME xxx.s3-website-us-west-1.amazonaws.com. xxx.s3-website-us-west-1.amazonaws.com. 60 IN CNAME s3-website-us-west-1.amazonaws.com. s3-website-us-west-1.amazonaws.com. 60 IN A yyy ;; Query time: 1514 msec ;; SERVER: 75.75.75.75#53(75.75.75.75) ;; WHEN: Fri Aug 22 12:32:13 2014 ;; MSG SIZE rcvd: 127 It seems OK to me. Why would Google tell me there is a DNS error? UPDATE: Google also cannot fetch robots.txt, but I can fetch it from my browser. UPDATE 2: I have a forwarding on the root to the www.* hostname: $ dig thenifty.me ; <<>> DiG 9.8.3-P1 <<>> thenifty.me ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 49286 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 1, ADDITIONAL: 0 ;; QUESTION SECTION: ;thenifty.me. IN A ;; AUTHORITY SECTION: thenifty.me. 300 IN SOA ns1hwy.name.com. support.name.com. 1 10800 3600 604800 300 ;; Query time: 148 msec ;; SERVER: 75.75.75.75#53(75.75.75.75) ;; WHEN: Fri Aug 22 13:32:56 2014 ;; MSG SIZE rcvd: 88

    Read the article

  • Default Critique branch office setup: VPNTunnel->HQ, subnets for VOIP/PC, + several Q's

    - by CHickenTaragon
    We're setting up a new branch office. * ~10 users. * Each user has a VOIP phone provided by a hosted solution. * Users need access to resources on HQ (located in another state), so setting up VPN tunnel * HQ only supports certain Cisco/Juniper devices. VOIP provider only supports SonicWall, so current plan is to have two routers w/ separate subnets for VOIP vs. PC traffic. * PC's will plug into pass-thru Ethernet jacks on the VOIP phones, but the phones vs. PC's will point to different subnets. * Cable Modem is 50Mbps / 5Mbps DOCSIS 3.0 business line w/ 5 static IP's. * Each of the 2 subnets will map to one of the 5 public IP's. * May or may not also need to support a VPN tunnel with a second branch office because of a file server they have there that some in the new office use. I'm pushing to have them move the files to a server on the HQ's network so we don't have to worry about setting up an additional tunnel. Questions: Do you foresee any issues with the below set-up? Router recommendations by HQ IT staff: Cisco Router 2811, or Juniper SSG5 or SSG20. Any recommendations about these routers? We need Wi-Fi too – looks like the above routers have models that support this, any reason not to use this? Users need to be able to work from home. If so, how is authentication handled? Right now we use AD credentials for the HQ's domain, but we currently don't plan to have an AD system in the new location since it's only 10 users. We can't tie the authentication system from the new location's router to the AD system of the HQ. All the PC's that will be in the new location are currently in the existing office that is closing down, and are already joined to the domain of the HQ. Please confirm: this + the VPN tunnel will be sufficient for them to connect to authenticated resources on the HQ's network from the new location, correct? Mainly SQL servers and file servers, and a few remote desktop sessions. I'm sure I'll have some more questions, but can't think of them right now.

    Read the article

  • Can not access network computers anymore

    - by Johny Skovdal
    Last Thursday (03/05/12) I got a new computer to be able to work from home. I plugged it, by cable, into the company network and installed most of the software needed for me to do so, by accessing a share on my stationary computer at work. I had no issues here what so ever, and everything just worked. Yesterday evening I tried accessing the company network trough Windows VPN, and while I was able to connect to the network, I was unable to connect to any computers on the network. I did, however, get an error when connecting, but I can't seem to get the error again, to get the details of the error message. Today I am sitting on the company network again, and now I can not access anything on the network like I could last Thursday, though I can ping all the computers I am attempting to access. Here is a list of details that might help in troubleshooting this issue (updated): List of observations / actions My computer is identical to another computer that has no issues. It is not on the domain but rather on the default workgroup, but this was not an issue last Thursday, so I am assuming it still is not. I am able to access my e-mail on the exchange server. I can connect to our TFS server from Visual Studio but not from Explorer. I can also connect to Database Servers and Remote Desktop. I can see several computers when browsing network computers, but I am unable to connect to any of them. When trying to connect to a computer I am consistently met with the error code "0x80070035" (network path not found). I also get the 0x80070035 error when double clicking the target computer from the Network UI. I am not met with a login dialog when trying to access a computer, as I should, since I am not on the domain. (I did login to both Exchange, Remote Desktop and TFS though) Between Thursday where it worked and Sunday evening where it did not, I have installed quite a few security updates, plus various tools etc. that I need for programming. I have tried accessing by computer name and ip and neither of them work. I can ping by computer name. I have deleted all (1 entry) stored network credentials. I am able to access my computer from the target computer. Client and Server can see each other on the network = Network Discovery is enabled. I am using the network profile "Work". When accessing the network through VPN, I am unable to get anything to work using computernames, but all of the above applies when using IP adresses instead of computername. I run Windows 7 Home Premium on my computer. Using powershell attempting to access a share I get the following error (ComputerName and ShareName being correct values of course): PS C:\Users\MyUser> cd \\ComputerName\ShareName Set-Location : Cannot find path '\\ComputerName\ShareName' because it does not exist. At line:1 char:3 + cd <<<< \\ComputerName\ShareName + CategoryInfo : ObjectNotFound: (\\ComputerName\ShareName:String) [Set-Location], ItemNotFoundException + FullyQualifiedErrorId : PathNotFound,Microsoft.PowerShell.Commands.SetLocationCommand However, ping'ing the same machine (ping ComputerName) from powershell I get response immediately. (As mentioned in the list of observations/actions, I tried the above with the IP address again on VPN, to get the same result) Conclusion So to sum up, pretty much the only thing I can not do, is access the other computers through browsing (explorer.exe, powershell, map networkdrive, etc.), which means that I am pretty much down to, that it is unable to resolve the path somehow, when trying to connect to other computers trough browsing, though the path gets resolved perfectly using all kinds of other services. Any recommendations as to what I can try next to resolve the issue? :)

    Read the article

  • Can I make my drives visible and change their partition type without losing my data?

    - by user165408
    I have made a lot of mistakes and now I cannot see my hard disk nor I can start my operating system on my laptop. All my passwords and important files on my hdd without any backup. I followed this course of action Changed my hard disk partitions to dynamic just for getting 5th partition. (1st mistake) Decreased partitions to 4 again. Backed up operating system from 4th to 3rd partition with Norton Ghost. Booted from a live CD for Windows XP. Formatted 4th partition and moved my all important data from 1st and 2nd partitions to the 4th partition. Deleted 1st and 2nd partitions and got 1 partition from half of empty space. So I have just 3 partitions and empty space between 1st and 2nd partitions. Tried to install Windows 8 to the first partition but it did not allow because it is dynamic. Also it did not allow to install to other partitions. Tried to install Windows XP to the 1st partition but it said if I continue I cannot use other drivers. Therefore I escaped from installing it. Booted from the Windows XP live CD then increased 1st partiton to less than 400mb of empty space. Therefore I thought it will be adjacent but it was shown as 2 partitions. In my computer I see just 3 drivers. Using Norton Ghost I recovered my OS to the 1st partition. (2nd mistake it was on 4th partition originally) Booted from a Windows XP live CD I tried to install bcdedit to the Windows XP live CD but it did not work. Then I tried to install EaseUS Partition Master Home Edition. It was installed with errors then I start it and it showed me an error like there is no hard disk. I looked to my PC and my drivers were not there. Booted from the Norton Ghost CD and it did not show me my drivers either, but before I was able to see them. I checked numbers of partition shown by the Norton Ghost utility and they are still have same numbers so I have to see my drivers but I cannot see them now. My hard disk is shown as extarnal dynamic now so I cannot see any drive in my PC in the live Windows XP. There are two options; first one is import extarnal disk and second one is convert disk to basic. Will they delete my data? I fear booting from CDs like Windows XP live CD, Norton Ghost CD, and the operating system CD/DVD, because they may overwrite a few MB their data to my data. These recover tools are already exist in Windows XP live CD by The Ultimate Boot CD for Windows. Can any of them help me? CompuAppa SwissKnife V3 DBXtract Disk Investigator Fab's AutoBackup 2.0 FileRecovery Floppy Repair Free Undelete Handy Recovery Recovery Manager Restorastion Restorastion Help File by UBCD4Win UnChk Unstoppable Copier Finally How can I make it so that my drives are visible again without losing my data? How can I convert my dynamic partitions to basic without losing my data?

    Read the article

  • Windows 7, HTTPS WebDav: Asks for password twice and fails. Any workarounds?

    - by AutoDMC
    Howdy. I have a Dav server running with PHP SabreDav (code.google.com/p/sabredav/wiki/Windows) on Cherokee at an HTTPS secured URL. It's set to use https, and uses Digest Authentication. I can log in with multiple browsers and a few third party clients (BitKinex and Java AnyClient can connect and browse as well, caveats below). However, when attempting to log in with Windows 7 (surprise, surprise), it asks for my password twice, then tells me that my folder is invalid. I have verified that the server is using Digest authentication. I've verified multiple times that third party software can connect. I even went out and bought a GoDaddy SSL certificate so my SSL wouldn't be self signed anymore. I've applied the registry hacks here: support.microsoft.com/kb/943280 (Note that the article says the "fix" already exists for Windows 7, I just need magical registry hax to get it to work) I've applied the registry hacks here: support.microsoft.com/kb/941050 I've applied the registry hacks here: support.microsoft.com/kb/841215 (Supposedly allows Basic Auth, which shouldn't apply, but why not?) All to no avail; Windows continues to ask for my password twice, then state that "The folder you entered does not appear to be valid. Please choose another." Try the command line? Sure: I've attempted to access with NET USE "https://dav.example.com/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/" (System error 1790) I've attempted to access with NET USE "https://dav.example.com/subdir/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/subdir/" (System error 1790) For good luck: ping dav.example.com ... works. And again, web browsers can access the share just fine, so can third party tools. Best I can tell at this point is "HAHA, NO WEBDAV FOR YOU ON WINDOWS 7" which would be fine except everyone who will be using this application... uses Windows 7. And most are not as persistent or pugnacious as I am. I feel like I've burned through every random suggestion I've found anywhere in the first 10 pages of Google on every search term I can think of. Any ideas? I need it to be Webdav, I need it to be over HTTPS, and I really do need a method to access it from Windows 7. EXTRA DETAIL: However, the "third party" programs I've tried have either been buggy, incomplete, or have silly ... "glitches." For example, BitKinex seems to fixate on any http error codes sent, so if there's a glitch reading a directory, BAM, that directory is always listed empty. Long directory listings also show up as blank, even though the transfer panel shows that directory listing is still taking place. In any case, BitKinex is useless for development purposes for the reasons above. And besides, I'm building this for people other than myself, people who will want to get this dav share working "the regular way."

    Read the article

  • Is this distributed database server idea feasible?

    - by David
    I often use SQLite for creating simple programs in companies. The database is placed on a file server. This works fine as long as there are not more than about 50 users working towards the database concurrently (though depending on whether it is reads or writes). Once there are more than this, they will notice a slowdown if there are a lot of concurrent writing on the server as lots of time is spent on locks, and there is nothing like a cache as there is no database server. The advantage of not needing a database server is that the time to set up something like a company Wiki or similar can be reduced from several months to just days. It often takes several months because some IT-department needs to order the server and it needs to conform with the company policies and security rules and it needs to be placed on the outsourced server hosting facility, which screws up and places it in the wrong localtion etc. etc. Therefore, I thought of an idea to create a distributed database server. The process would be as follows: A user on a company computer edits something on a Wiki page (which uses this database as its backend), to do this he reads a file on the local harddisk stating the ip-address of the last desktop computer to be a database server. He then tries to contact this computer directly via TCP/IP. If it does not answer, then he will read a file on the file server stating the ip-address of the last desktop computer to be a database server. If this server does not answer either, his own desktop computer will become the database server and register its ip-address in the same file. The SQL update statement can then be executed, and other desktop computers can connect to his directly. The point with this architecture is that, the higher load, the better it will function, as each desktop computer will always know the ip-address of the database server. Also, using this setup, I believe that a database placed on a fileserver could serve hundreds of desktop computers instead of the current 50 or so. I also do not believe that the load on the single desktop computer, which has become database server will ever be noticable, as there will be no hard disk operations on this desktop, only on the file server. Is this idea feasible? Does it already exist? What kind of database could support such an architecture?

    Read the article

  • Permission Mystery - apt-get and other system utilities have 000 permissions

    - by emteh
    I'm trying to track down this strange behavoir for years now. Always after installing software-updates the permissions of a lot of system-tools are broken as you can see below. I am reasonable convinced that the machine is not owned by someone else. Regular security updates + grsecurity kernel + pax + daily rkhunter runs. Besides that there is no incentive for an attacker to fiddle in such obvious ways with the system. I installed bastille linux (http://bastille-linux.sourceforge.net/) und tried to deinstall it later, so the problems could be related to that. However I don't see how this can happen in a regular way after updates. System: Ubuntu 10.04, recently updated to Ubuntu 12.04 but the problem persists. Apt-Configuration in /etc/apt/ looks sane to me. But nevertheless - could here be the source of the trouble? DPkg::Pre-Install-Pkgs {"/usr/sbin/dpkg-preconfigure --apt || true";}; DPkg::Post-Invoke { "if [ -x /usr/bin/debsums ]; then /usr/bin/debsums -- generate=nocheck -sp /var/cache/apt/archives; fi"; }; // Makes sure that rkhunter file properties database is updated // after each remove or install only APT_AUTOGEN is enabled DPkg::Post-Invoke { "if [ -x /usr/bin/rkhunter ] && grep -qiE '^APT_AUTOGEN=.? (true|yes)' /etc/default/rkhunter; then /usr/share/rkhunter/scripts/rkhupd.sh; fi" } DPkg::Post-Invoke {"if [ -d /var/lib/update-notifier ]; then touch /var/lib/update- notifier/dpkg-run-stamp; fi; if [ -e /var/lib/update-notifier/updates-available ]; then echo > /var/lib/update-notifier/updates-available; fi "; }; Where do these chmod 000 come from? I'm feeling really uneasy with this problem. root@besen:~# find /usr/bin/ -perm 0 -ls 14721496 196 ---------- 1 root root 192592 Oct 15 11:58 /usr/bin/apt-get 14721144 68 ---------- 1 root root 63848 Sep 13 00:29 /usr/bin/gpasswd root@besen:~# find /usr/sbin/ -perm 0 -ls 1727732 92 ---------- 1 root root 86984 Sep 13 00:29 /usr/sbin/usermod 1727727 64 ---------- 1 root root 57640 Sep 13 00:29 /usr/sbin/userdel 1727719 64 ---------- 1 root root 57680 Sep 13 00:29 /usr/sbin/newusers 1727718 40 ---------- 1 root root 38632 Sep 13 00:29 /usr/sbin/grpunconv 1727728 48 ---------- 1 root root 47088 Sep 13 00:29 /usr/sbin/groupadd 1727724 32 ---------- 1 root root 29584 Sep 13 00:29 /usr/sbin/pwunconv 19031620 84 ---------- 1 root root 81880 Jan 3 2012 /usr/sbin/edquota 14877113 48 ---------- 1 root root 46880 Sep 13 00:29 /usr/sbin/grpck 1727722 40 ---------- 1 root root 38632 Sep 13 00:29 /usr/sbin/pwck 1727730 96 ---------- 1 root root 91464 Sep 13 00:29 /usr/sbin/useradd 19031619 16 ---------- 1 root root 14600 Jan 3 2012 /usr/sbin/quotastats 1727720 44 ---------- 1 root root 42760 Sep 13 00:29 /usr/sbin/groupdel 1727733 36 ---------- 1 root root 34504 Sep 13 00:29 /usr/sbin/pwconv 19031621 80 ---------- 1 root root 77632 Jan 3 2012 /usr/sbin/rpc.rquotad 19030041 76 ---------- 1 root root 73600 Jan 3 2012 /usr/sbin/repquota 1727731 40 ---------- 1 root root 38624 Sep 13 00:29 /usr/sbin/grpconv 1727725 56 ---------- 1 root root 49472 Sep 13 00:29 /usr/sbin/vipw 1727723 64 ---------- 1 root root 57672 Sep 13 00:29 /usr/sbin/groupmod root@besen:~# find /sbin/ -perm 0 -ls 16760927 76 ---------- 1 root root 73464 Jan 3 2012 /sbin/quotaon Any tipps? I really can't pinpoint the problem in more detail. It happens after installing updates but I can't find no hooks in the dpkg/apt system.

    Read the article

  • batch file to deploy files

    - by Martin Michalak
    hi I have created batch file which pulls info from *.txt file and deploy code from the source to destination: SET Source=%1 if exist %Source% ( ECHO Source for WEB exists ) else ( ECHO Wrong build%Source% doesn't exist GOTO Menu ) SET Server=%2 SET AppPool=%3 SET Destination=%4 SET Folder=%5 SET ENV=%6 SET AppName=%7 SET Envlog=%8 ECHO Deployment of WEB > %Envlog% %Date% %Time% echo. @ECHO Stopping App Pools @ECHO Stopping App Pools >> %Envlog% %Date% %Time% D:\ICTTools\PSEXEC.EXE -d \\%Server% cmd.exe /c c:\windows\system32\inetsrv\appcmd STOP apppool /apppool.name:%AppPool% echo. @ECHO App Pools will be stopped in the background @ECHO App Pools will be stopped in the background >> %Envlog% %Date% %Time% Pause echo. IF EXIST "%Destination%" ( ECHO Deleting %AppName% %Folder% RMDIR %Destination% /s /q ECHO Destination Folder %Folder% Deleted ECHO Destination Folder %Folder% Deleted >> %Envlog% %Date% %Time% ) else ( ECHO Destination Folder %Destination% does not exist, please check ECHO Destination Folder %Destination% does not exist, please check >> %Envlog% %Date% %Time% Pause ) echo. @ECHO Starting Robocopy for %AppName% @ECHO Starting Robocopy for %AppName% >> %Envlog% %Date% %Time% echo. START /WAIT /MIN ROBOCOPY.EXE %Source% %Destination% *.* /S /NP /R:3 /W:5 /LOG:"Logs\Robo%AppName%%ENV%.log" D:\Tools\Windiff\windiff.exe %Source% %Destination% echo. @ECHO Finished with Robocopy @ECHO Finished with Robocopy >> %Envlog% %Date% %Time% echo. @ECHO Checking if App pools stopped: @ECHO Checking if App pools stopped: >> %Envlog% %Date% %Time% D:\ICTTools\PSEXEC.EXE \\%Server% c:\windows\system32\inetsrv\appcmd LIST apppool /apppool.name:%AppPool% @echo off set /p ask=All app pools stopped? (y/n) if %ask%==y (echo Great, please continue with deployemnt) else echo Before continuing please check why app pools did not stop @echo App pools stopped?: %ask% >> %Envlog% %Date% %Time% DEL %Source%\web.config echo. @ECHO Production Config check if exist "%Destination%\%ENV%-Web.config" ( echo. ECHO The Application production configuration file does exist. ECHO The Application production configuration file does exist. >> %Envlog% %Date% %Time% COPY %Destination%\%ENV%-Web.config web.config echo. ECHO Production %ENV%-Web.config has been renamed to web.config ECHO Production %ENV%-Web.config has been renamed to web.config >> %Envlog% %Date% %Time% ) else ( ECHO The Application production configuration file is missing in Production %AppName% ECHO The Application production configuration file is missing in Production %AppName% >> %Envlog% %Date% %Time% explorer %Destination% Pause ) echo. @ECHO Confirm that configs were renamed correclty, if yes please hit any key to START APP Pools @ECHO Confirm that configs were renamed correclty, if yes please hit any key to START APP Pools >> %Envlog% %Date% %Time% Pause echo. @ECHO Start %AppName% Application Pool >> %Envlog% %Date% %Time% D:\ICTTools\PSEXEC.EXE \\%Server% c:\windows\system32\inetsrv\appcmd START apppool /apppool.name:%AppPool% @echo off set /p ask=All app pools started? (y/n) if %ask%==y (echo Great, please continue with deployemnt) else echo Before continuing please check why app pools did not start @echo App pools started?: %ask% >> %Envlog% %Date% %Time% Pause echo. @ECHO Build Version for %AppName% @ECHO Build Version for %AppName% >> %Envlog% %Date% %Time% type %Destination%\buildinfo.xml echo. ECHO ............................................... @ECHO ...........Deployment Compelted................ @ECHO ...........Deployment Compelted................>> %Envlog% %Date% %Time% ECHO ............................................... here are my issues: Lets say I am running code for 3 servers, then for each instance: For all three servers I am performing destination folder delete even so destination folder is always the same, the code should only delete it in the 1st instance (when code is deployed to first server) then I would prefer if script would check if the code from the source and destination is the same and if it is it should delete the folder or not. Then based on 1: a) deleting web.config and renaming should only happen if code in destination is new b) Robocopy should not override files if they are the same I think there is /Xo option to do that any idea how to achieve that? :)

    Read the article

  • Switch flooding when bonding interfaces in Linux

    - by John Philips
    +--------+ | Host A | +----+---+ | eth0 (AA:AA:AA:AA:AA:AA) | | +----+-----+ | Switch 1 | (layer2/3) +----+-----+ | +----+-----+ | Switch 2 | +----+-----+ | +----------+----------+ +-------------------------+ Switch 3 +-------------------------+ | +----+-----------+----+ | | | | | | | | | | eth0 (B0:B0:B0:B0:B0:B0) | | eth4 (B4:B4:B4:B4:B4:B4) | | +----+-----------+----+ | | | Host B | | | +----+-----------+----+ | | eth1 (B1:B1:B1:B1:B1:B1) | | eth5 (B5:B5:B5:B5:B5:B5) | | | | | | | | | +------------------------------+ +------------------------------+ Topology overview Host A has a single NIC. Host B has four NICs which are bonded using the balance-alb mode. Both hosts run RHEL 6.0, and both are on the same IPv4 subnet. Traffic analysis Host A is sending data to Host B using some SQL database application. Traffic from Host A to Host B: The source int/MAC is eth0/AA:AA:AA:AA:AA:AA, the destination int/MAC is eth5/B5:B5:B5:B5:B5:B5. Traffic from Host B to Host A: The source int/MAC is eth0/B0:B0:B0:B0:B0:B0, the destination int/MAC is eth0/AA:AA:AA:AA:AA:AA. Once the TCP connection has been established, Host B sends no further frames out eth5. The MAC address of eth5 expires from the bridge tables of both Switch 1 & Switch 2. Switch 1 continues to receive frames from Host A which are destined for B5:B5:B5:B5:B5:B5. Because Switch 1 and Switch 2 no longer have bridge table entries for B5:B5:B5:B5:B5:B5, they flood the frames out all ports on the same VLAN (except for the one it came in on, of course). Reproduce If you ping Host B from a workstation which is connected to either Switch 1 or 2, B5:B5:B5:B5:B5:B5 re-enters the bridge tables and the flooding stops. After five minutes (the default bridge table timeout), flooding resumes. Question It is clear that on Host B, frames arrive on eth5 and exit out eth0. This seems ok as that's what the Linux bonding algorithm is designed to do - balance incoming and outgoing traffic. But since the switch stops receiving frames with the source MAC of eth5, it gets timed out of the bridge table, resulting in flooding. Is this normal? Why aren't any more frames originating from eth5? Is it because there is simply no other traffic going on (the only connection is a single large data transfer from Host A)? I've researched this for a long time and haven't found an answer. Documentation states that no switch changes are necessary when using mode 6 of the Linux interface bonding (balance-alb). Is this behavior occurring because Host B doesn't send any further packets out of eth5, whereas in normal circumstances it's expected that it would? One solution is to setup a cron job which pings Host B to keep the bridge table entries from timing out, but that seems like a dirty hack.

    Read the article

  • Problems with XP, Office, and PC in general - any ideas?

    - by molecule
    Hi all This may not make a whole lot of sense so pls bear with me... I am about to perform a routine check on one of my user's PC. Some background - the PC has a Xeon processor and 4Gb of RAM and running XP SP3 He has 2xHDD and pagefile is hosted on the secondary HDD (D:) and min/max values are set to 4096. NO pagefile on C: This user has 6 monitors so he has an NVIDIA Quadro NVS440 hosting 4xmonitors and an NVIDIA Quadro NVS290 hosting 2xmonitors. There is a video card driver from NVIDIA which is compatible with both NVS440 and NVS290 and he is on the latest version of that driver. (Note: Make of video cards are different - one is from leadtek and the other from Nvidia) He is a heavy Bloomberg, Outlook, Word, and Excel user and runs two Citrix applications. Other apps are FoxIt PDF and IE. Problems - Outlook and Excel frequently crashes - I am going to perform an Outlook and Excel repair and also check/remove unnecessary addins - will he lose any customizations if I repaired and chose "Restore my shortcuts while repairing" and do not select "Discard my customized settings and restore default settings". Does repair really repair anything? FYI - It stopped crashing ever since i moved a large spreadsheet he has open to his local HDD instead of over the network. This spreadsheet "refreshes" constantly as it is pulling live data to update cells and I suspect it was auto-saving so frequently that it caused crashes if saving over the network. At times, his right click completely fails to respond. His left click works fine but he can't right click on anything in any Window and even on the desktop. Sometimes, he needs to start to close certain applications such as Adobe and the right click will start functioning again. I removed Adobe and installed FoxIt as I figured it was a resource issue but I do not think so as he does have sufficient resources when the problem is happening. Sometimes he can't bring task manager up until he kills certain apps. Definitely sounds like a resource issue but I am not confident that is the root cause. Also not sure if this is related to one of the apps installed but his Start bar flickers (does not completely disappear) intermittently from time to time. The taskbar icons which are hidden appear and then get hidden again as if it was having "fits". I have performed reg scans, malware scans etc but problems do not go away. I am planning to perform sfc /scannow and office repair but would like to know if anyone has any other suggestions. What about setting a "small" pagefile on C:. I have heard that this is recommended and may be the reason why a minidmp file was not generated when he encountered a blue screen. Also, any feedback on his video cards? Do you think different models would cause problems? The drivers seem to work but he only has 2.5Gb out of 4Gb available RAM as I believe the video card chomped up a portion of this. I have recommended creating a new profile for him but due to the amount of customisations he has and the amount of time and effort it will take to get him up and running again, he prefers to bear with the problem than to go down that path. However, at least once a week, his PC acts up and I can't think of any other tools or techniques to rectify his problems. I guess we are at a stage where we just want to "stabilize" things so he won't encounter issues that frequently. Any feedback is very much appreciated.

    Read the article

  • Biztalk 2009 install help

    - by _pemex99_
    Hi, I try to install Biztalk2009, with SQL 2008R2CTPNov, on Win Server 2008. I'm blocked at the configuration step "groups" : [19:22:18 Info Configuration Framework]Configuring feature: WMI [19:22:18 Info BtsCfg] Entering function: CBtsCfg::ConfigureFeature [19:22:18 Info BtsCfg] Configuring feature: WMI [19:22:18 Info BtsCfg] Entering function: CBtsCfg::IsSelectedAnswer [19:22:18 Info BtsCfg] Leaving function: CBtsCfg::IsSelectedAnswer [19:22:18 Info BtsCfg] Entering function: CWMI::Connect [19:22:18 Info BtsCfg] WMI is already connected [19:22:18 Info BtsCfg] Leaving function: CWMI::Connect [19:22:18 Info ConfigHelper] NT group BizTalk Server Operators was not created because it already exists [19:22:18 Info ConfigHelper NetAPI Info: ] Le groupe local spécifié existe déjà. [19:22:18 Info ConfigHelper] NT group BizTalk Server Administrators was not created because it already exists [19:22:18 Info ConfigHelper NetAPI Info: ] Le groupe local spécifié existe déjà. [19:22:18 Info BtsCfg] Entering function: CWMI::CreateGroup 2010-01-14 19:22:18:0527 [INFO] WMI CWMIInstProv::PutInstance() try to acquire lock 2010-01-14 19:22:18:0539 [INFO] WMI CWMIInstProv::PutInstance() lock acquired successfully 2010-01-14 19:22:18:0546 [INFO] WMI CWMIInstProv::VerifyMgmtDbCompatibility(CInstance) started 2010-01-14 19:22:18:0553 [INFO] WMI CWMIInstProv::VerifyMgmtDbCompatibility(CInstance) finished successfully 2010-01-14 19:22:18:0564 [INFO] WMI CWMIInstProv::PutInstance(MSBTS_GroupSetting.MgmtDbName="BizTalkMgmtDb",MgmtDbServerName="ECTXEVLBZTK") started 2010-01-14 19:22:18:0572 [INFO] WMI CAdapter::ConvertWMI2Admin() started 2010-01-14 19:22:18:0581 [INFO] WMI CDataContainer::SetWCHAR() - Possible problem: item value is overwritten 2010-01-14 19:22:18:0591 [INFO] WMI CAdapter::ConvertWMI2Admin() finished with HR=0 2010-01-14 19:22:18:0611 [INFO] WMI QueryStringValue query regkey 'MgmtDBServer' 2010-01-14 19:22:18:0620 [INFO] WMI CAdmCoreGroupInst::TryCreateNewGroup() started 2010-01-14 19:22:18:0632 [INFO] WMI Creating Mgmt database... 2010-01-14 19:22:18:0641 [INFO] WMI Calling CDataSource.Open() against ECTXEVLBZTK\master 2010-01-14 19:22:18:0792 [INFO] WMI CDataSource.Open() returned 2010-01-14 19:22:18:0810 [WARN] AdminLib GetBTSMessage: hrErr=80040e1d; Msg=Error "0x80040E1D" occurred.; 2010-01-14 19:22:18:0824 [WARN] AdminLib GetBTSMessage: hrErr=c0c02524; Msg=Failed to create Management database "BizTalkMgmtDb" on server "ECTXEVLBZTK". Error "0x80040E1D" occurred.; 2010-01-14 19:22:18:0835 [ERR] WMI Failed in pAdmInst->Create() in CWMIInstProv::PutInstance(). HR=c0c02524 2010-01-14 19:22:18:0846 [ERR] WMI WMI error description is generated: Failed to create Management database "BizTalkMgmtDb" on server "ECTXEVLBZTK". Error "0x80040E1D" occurred. 2010-01-14 19:22:18:0860 [INFO] WMI CWMIInstProv::PutInstance() finished. HR=c0c02524 [19:22:18 Error BtsCfg] f:\bt\890\private\source\setup\prod\btssetup\btscfg\btswmi.cpp(358): FAILED hr = c0c02524 [19:22:18 Error BtsCfg] Failed to create Management database "BizTalkMgmtDb" on server "ECTXEVLBZTK". Error "0x80040E1D" occurred. It seems that the install can't create Managment database, But the SSO database is created OK... Has someone a clue ?

    Read the article

  • Pairing Bluetooth device with PIN fails

    - by Pikaro
    I'm trying to pair my old BlackBerry 8310 to my Linux desktop (up-to-date Debian Sid, 3.15-10.dmz.1-liquorix-amd64) by using blueman and its associated tools. Scanning for the device works equally well for both sides; however, I am unable to pair the two once it comes to entering the PIN. If I scan from my PC, I have two options in blueman-manager regarding my phone: Directly selecting "pair", or selecting "setup". If I select "pair", nothing happens on my desktop, but the phone asks me to enter a PIN; if I do so, it reports that pairing has failed. During that, nothing is logged to the console. Selecting "setup" opens a configuration dialog that allows for entering or generating a PIN. Regardless, I get to a screen that tells me to enter the PIN on the phone, and at the same time, the phone pops up the equivalent dialog. This would be what one would expect to work; but whatever I enter (naturally, the same on both), both devices report that pairing has failed, and blueman-manager logs init_services (/usr/lib/python2.7/dist-packages/blueman/main/Device.py:73) Loading services org.bluez.Error.AuthenticationFailed: Authentication Failed If I instead try to pair from the phone, I cannot see any kind of reaction from my desktop - all I get is the equivalent "pairing failed" message from the BlackBerry after I entered a PIN in the dialog that pops up there. hcitool scan and hciconfig -a work without complaints, but I cannot find a way to try the pairing as a whole on the console since bluez-simple-agent seems to have been discontinued and this recommendation is everywhere on Google. hcitool cc as root opens the PIN dialog on the phone, then fails with "Input/Output error" once I enter it. The user is not permitted to execute this command. I also tried creating /usr/lib/bluetooth/<MAC>/pincodes to manually define a persistent PIN, which seems to have had no effect. The same goes for running the different commands as root, though I'm really confused about the internal structure of the Bluetooth subsystem now: They usually and inconsistently failed with Python or DBUS errors or just showed the same results. The only other Bluetooth device I have around are a pair of Creative speakers. Trying "setup" asks me to enter a key on them, which is impossible. If I try "pair", I'm asked for a PIN as I should, but no pairing takes place, and no errors appear on the console. (It just repeats their name a few times.) Interestingly, I tried that before writing my question, and nothing happened in terms of PIN questions, just like with the BlackBerry, which still shows no change. I don't think I actively changed anything since then. The BlackBerry can pair with and connect to the speakers, and everything goes as one would expect, so the problem is definitely with my desktop. So thus my questions: What is that PIN window generated by, and why does it seem to appear randomly? How can I find out what, exactly, fails after trying to add the speakers, as this may give me a clue? Is there any kind of complete log that concerns itself with Bluetooth? What data can I provide to make this more solvable?

    Read the article

< Previous Page | 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492  | Next Page >