Search Results

Search found 410 results on 17 pages for 'voip'.

Page 15/17 | < Previous Page | 11 12 13 14 15 16 17  | Next Page >

• Handling multiple accounts in Android app

  - by bebeTech

  I would like to build an application that caters for multiple accounts (eg. home, work) and account types (e.g. ISP, VoIP, Mobile). Essentially, I would like to get the user to create the accounts they want and then have all the accounts listed on the start page grouped by type. For example: ISP: - Home - Work Mobile: - Mum - Dad When you click on the account, it would take you to another screen where I do a bunch of calcs and display the results. I currently do this via multiple apps but am looking at consolidating into the one app. I am just not sure where to start or how I go about achieving this? The way the Contacts app works is a good example of what I am wanting to do.

  Read the article

• router gets disconnected once I terminate my SIP application

  - by TacB0sS

  Hey, Here is an interesting one, I have a SIP VoIP application which is able to register to the PBX server, and I can invite and see the user call on the callee end receiving an Invite, and on the caller end I see the Ringing response... now here is interesting part, if I close my application with out any notification to the server my router disconnects and restart, after a short while (30 - 150 sec). I could fix that if I would complete the ACK BYE process, but I'm just wondering why does my router hangs up? any ideas?

  Read the article

• How to add an audio filter to AudioRecord (on Android)?

  - by Jim

  I would like to write a "daemon" application that will add a special audio filter (e.g. audio enhancement) to AudioRecord. The result should be as follows: Whenever any VoIP application (e.g. Skype,...) will create an AudioRecord, the captured audio will be first filtered using my daemon application before it reaches Skype. Is this doable ? For example can I use an AudioSessionID=0 to attach my filter to all the input channels ?

  Read the article

• Customizing Sipdroid

  - by Seshu Vinay

  I have a Voip based app. So i thought of customizing SipDroid open source project. As the starting phase i have changed all the package names, Class names etc. It perfectly works on my Samsung Galaxy Y. But i tried with many other mobiles, Voice is not audible. Call is being initialized but could not hear voice. In Samsung galaxy young, voice is clearly audible for both incoming and outgoing calls. But in all the other phones i have tested i can hear only beep sounds. What could be the problem? I tried calling the other mobile(that has Sip Droid) with my Samsung Galaxy Young(customized app) I could hear voice in my app but could not hear in Sipdroid. But when i tried calling Sipdroid to Sipdroid, it works fine in all the mobiles.

  Read the article

• gstreamer pulseaudio echo cancellation

  - by user3618055

  I'm implementing a voip application using gstreamer, i use the example of the rtp in the plugin-good! i want to implement echo cancellation, i couldn't use the speex echo canceller with gstreamer because the input and the output are not in the same process. So, i want to use pulse audio to make echo cancellation? can any one help me how to deal with? the sender voice is pipeline = gst_pipeline_new (NULL); g_assert (pipeline); /* the audio capture and format conversion */ audiosrc = gst_element_factory_make (pulsesrc, "audiosrc"); g_assert (audiosrc); audioconv = gst_element_factory_make ("audioconvert", "audioconv"); g_assert (audioconv); audiores = gst_element_factory_make ("audioresample", "audiores"); g_assert (audiores); /* the encoding and payloading */ audioenc = gst_element_factory_make (AUDIO_ENC, "audioenc"); g_assert (audioenc); audiopay = gst_element_factory_make (AUDIO_PAY, "audiopay"); g_assert (audiopay); /* add capture and payloading to the pipeline and link */ gst_bin_add_many (GST_BIN (pipeline), audiosrc, audioconv, audiores, audioenc, audiopay, NULL); if (!gst_element_link_many (audiosrc, audioconv, audiores, audioenc, audiopay, NULL)) { g_error ("Failed to link audiosrc, audioconv, audioresample, " "audio encoder and audio payloader"); } and the receiver is : gst_bin_add_many (GST_BIN (pipeline), rtpsrc, rtcpsrc, rtcpsink, NULL); /* the depayloading and decoding */ audiodepay = gst_element_factory_make (AUDIO_DEPAY, "audiodepay"); g_assert (audiodepay); audiodec = gst_element_factory_make (AUDIO_DEC, "audiodec"); g_assert (audiodec); /* the audio playback and format conversion */ audioconv = gst_element_factory_make ("audioconvert", "audioconv"); g_assert (audioconv); audiores = gst_element_factory_make ("audioresample", "audiores"); g_assert (audiores); audiosink = gst_element_factory_make (pulsesink, "audiosink"); g_assert (audiosink); /* add depayloading and playback to the pipeline and link */ gst_bin_add_many (GST_BIN (pipeline), audiodepay, audiodec, audioconv, audiores, audiosink, NULL); res = gst_element_link_many (audiodepay, audiodec, audioconv, audiores, audiosink, NULL); g_assert (res == TRUE); i tried to change gstreamer proprietes to pulseaudio server in input and output and i used "pactl load-module module-echo-cancel aec_method=adrian" but i still listen to echo!! any one could help please thanks!!

  Read the article

• WebCenter Customer Spotlight: Global Village Telecom Ltda

  - by me

  Author: Peter Reiser - Social Business Evangelist, Oracle WebCenter  Solution SummaryGlobal Village Telecom Ltda. (GVT)  is a leading Brazilian telecommunications company, developing solutions and providing services for corporate and end users. GVT is located in Curitiba, Brazil, employs 6,000 people and has an annual revenue of around US$1 billion.  GVT business objectives were to improve corporate communications, accelerate internal information flow, provide continuous access to the all business files and  enable the company’s leadership to provide information to all departments in real time. GVT implemented Oracle WebCenter Content to centralize the company's content and they built  a portal to share and find content in real-time. Oracle WebCenter Content enabled GVT to quickly and efficiently integrate communication among all company employees—ensuring that GVT maintain a competitive edge in the market. Human Resources reduced the time required for issuing internal statements to all staff from three weeks to one day. Company OverviewGlobal Village Telecom Ltda. (GVT)  is a leading telecommunications company, developing solutions and providing services for corporate and end users. The company offers diverse innovative products and advanced solutions in conventional fixed telephone communications, data transmission, high speed broadband internet services, and voice over IP (VoIP) services for all market segment. GVT is located in Curitiba, Brazil, employs 6,000 people and have an  annual revenue of around US$1 billion.   Business ChallengesGVT business objectives were to improve corporate communications, accelerate internal information flow, provide continuous access to the all business files and enable the company’s leadership to provide information to all departments in real time. Solution DeployedGVT worked with the Oracle Partner IT7 to deploy Oracle WebCenter Content to securely centralize the company's content such as growth indicators, spreadsheets, and corporate and descriptive project schedules. The solution enabled real-time information sharing through the development of Click GVT, a portal that currently receives 100,000 monthly impressions from employee searches. Business ResultsGVT gained a competitive edge in the communications market by accelerating internal information flow, streamlining the content standardizing information and enabled real-time information sharing and discovery. Human Resources  reduced the time required for issuing  internal statements to all staff from three weeks to one day. “The competitive nature of telecommunication industry demands rapid information in the internal flow of the company. Oracle WebCenter Content enabled us to quickly and efficiently integrate communication among all company employees—ensuring that we maintain a competitive edge in the market.” Marcel Mendes Filho, Systems Manager, Global Village Telecom Ltda. Additional Information Global Viallage Telecom Ltda Customer Snapshot Oracle WebCenter Content

  Read the article

• RTS Game Style Application [closed]

  - by Daniel Wynand van Wyk

  My question may seem somewhat odd, but I hope that my specifications will clarify EXACTLY what it is that I am after. I need some help choosing the right tooling for a particular endeavour. My background is in desktop application development and large back-end systems. I have worked primarily on the Microsoft stack using C# and the .Net framework. My goal is to develop a 2D, RTS style, interactive office simulation. The simulation will model various office spaces, office equipment, employees and their interactions with one another. The idea is to abstract the concept of an office completely. Under the hood the application will do many things that are nothing like a game. This includes P2P networking, VPN tunnelling, streaming video, instant messaging, document collaboration, remote screen sharing, file-sharing, virus scanning, VOIP, document scanning, faxing, emailing, distributed computing, content management and much more! A somewhat similar thing has been attempted by IBM, where they created a virtual office in second life. If their attempt was a game, the game-play would be notably horrible, to say the least! The users/players will drive and control my application through the various objects modelled in the simulation. A single application capable of performing all of these various tasks would be a nightmare to navigate for even the most expert user. Using the concept of a game, I can easily separate functionality by assigning them to objects that relate 1-1 with their real world counter-parts. This can greatly simplify computing for novice users, with many added benefits in terms of visibility, transparency of process and centralized configuration. My hope is to make complex computing tasks accessible to all kinds of users and to greatly reduce the cognitive load associated with using the many different utilities and applications inside office settings. The complexity is therefore limited to the complexity of the space in which you find yourself. I want the application to target as many platforms as possible and run on computers that have no accelerated graphics capabilities. The simulation won't contain any of the fancy eye-candy you find in modern games, to the contrary, my "game" will purposefully be clean and simple. The closest thing I could imagine would be an old game like "Theme Hospital" or the first instalment of "The Sims". All the content will be pre-created and not user-generated like Second Life. New functionality will be added via a plugin system. Given my background and nature of my "game", I would like to spend most of my time writing code that does not have to do with the simulated office, as the "game" is really just a glorified application menu. I have done much reading about existing engines, frameworks and tools. I need the help of an experienced game developer who has tried and tested various products over the years who can guide me in the right direction given my very particular needs. I would appreciate any help I can get!

  Read the article

• What You Said: Staying Productive While Working from home

  - by Jason Fitzpatrick

  Earlier this week we asked you to share your telecommuting/work-from-home productivity tips. Now we’re back with a tips and tricks roundup; read on to see how your fellow readers stay focused at home. By far and away the most common technique deployed as carefully isolating work from home life. Carol writes: I love working from home and have done so for 6 years now. I have a routine just as if I was going to an office, except my commute is 12 steps. I get ready for work, grab my purse and smart phone and go to up the steps to my office. I maintain a separate phone line and voice mail for work that I cannot answer from anywhere but my work desk. I use call forwarding when I travel so only my office phone number is published. I have VOIP phone service so I can forward calls from the internet if I forget, or need to change where the phone is forwarded. I do have a wired and wireless head set so I can go get a cold drink if on one of those long boring conference calls. I plan my ‘get off from work’ time and try to stick to it, as with any job some days I am late getting off, but it all works out. I make sure my office is for work only, any other computer play time is in a different part of the house on different computer. My office has laptop, dock, couple of monitors, multipurpose printer, fax, scanner, file cabinets – just like the office at a company. I just also happen to have a couple of golden retrievers that come to work with me and usually lay quietly until 5, and yes they know it is 5pm sometimes before I do. For me, one of the biggest concerns when working from home is not being unproductive, but the danger of never stopping work. You could keep going and going because let’s face it – the company will let you do it, so I set myself up to prevent that and maintain a separateness. HTG Explains: Does Your Android Phone Need an Antivirus? How To Use USB Drives With the Nexus 7 and Other Android Devices Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder?

  Read the article

• Creating a Yes/No MessageBox in a NuGet install/uninstall script

  - by ParadigmShift

  Sometimes getting a little feedback during the install/uninstall process of a NuGet package could be really useful. Instead of accounting for all possible ways to install your NuGet package for every user, you can simplify the installation by clarifying with the user what they want. This example shows how to generate a windows yes/no message box to get input from the user in the PowerShell install or uninstall script. We’ll use the prompt on the uninstall to confirm if the user wants to delete a custom setting that the initial install placed in their configuration.  Obviously you could use the prompt in any way you want. The objects of the message box are generated similar to the controls in the code behind of a WinForm. At the beginning of your script enter this: param($installPath, $toolsPath, $package, $project)   # Set up path variables $solutionDir = Get-SolutionDir $projectName = (Get-Project).ProjectName $projectPath = Join-Path $solutionDir $projectName   ################################################################################################ # WinForm generation for prompt ################################################################################################ function Ask-Delete-Custom-Settings { [void][reflection.assembly]::loadwithpartialname("System.Windows.Forms") [Void][reflection.assembly]::loadwithpartialname("System.Drawing")   $title = "Package Uninstall" $message = "Delete the customized settings?" #Create form and controls $form1 = New-Object System.Windows.Forms.Form $label1 = New-Object System.Windows.Forms.Label $btnYes = New-Object System.Windows.Forms.Button $btnNo = New-Object System.Windows.Forms.Button   #Set properties of controls and form ############ # label1 # ############ $label1.Location = New-Object System.Drawing.Point(12,9) $label1.Name = "label1" $label1.Size = New-Object System.Drawing.Size(254,17) $label1.TabIndex = 0 $label1.Text = $message   ############# # btnYes # ############# $btnYes.Location = New-Object System.Drawing.Point(156,45) $btnYes.Name = "btnYes" $btnYes.Size = New-Object System.Drawing.Size(48,25) $btnYes.TabIndex = 1 $btnYes.Text = "Yes"   ########### # btnNo # ########### $btnNo.Location = New-Object System.Drawing.Point(210,45) $btnNo.Name = "btnNo" $btnNo.Size = New-Object System.Drawing.Size(48,25) $btnNo.TabIndex = 2 $btnNo.Text = "No"   ########### # form1 # ########### $form1.ClientSize = New-Object System.Drawing.Size(281,86) $form1.Controls.Add($label1) $form1.Controls.Add($btnYes) $form1.Controls.Add($btnNo) $form1.Name = "Form1" $form1.Text = $title #Event Handler $btnYes.add_Click({btnYes_Click}) $btnNo.add_Click({btnNo_Click}) return $form1.ShowDialog() } function btnYes_Click { #6 = Yes $form1.DialogResult = 6 } function btnNo_Click { #7 = No $form1.DialogResult = 7 } ################################################################################################ This has also wired up the click events to the form.  This is all it takes to create the message box. Now we have to actually use the message box and get the user’s response or this is all pointless.  We’ll then delete the section of the application/web configuration called <Custom.Settings> [xml] $configXmlContent = Get-Content $configFile   Write-Host "Please respond to the question in the Dialog Box." $dialogResult = Ask-Delete-Custom-Settings #6 = Yes #7 = No Write-Host "dialogResult = $dialogResult" if ($dialogResult.ToString() -eq "Yes") { Write-Host "Deleting customized settings" $customSettingsNode = $configXmlContent.configuration.Item("Custom.Settings") $configXmlContent.configuration.RemoveChild($customSettingsNode) $configXmlContent.Save($configFile) } if ($dialogResult.ToString() -eq "No") { Write-Host "Do not delete customized settings" } The part where I check if ($dialog.Result.ToString() –eq “Yes”) could just as easily check the value for either 6 or 7 (Yes or No).  I just personally decided I liked this way better.   Shahzad Qureshi is a Software Engineer and Consultant in Salt Lake City, Utah, USA His certifications include: Microsoft Certified System Engineer 3CX Certified Partner Global Information Assurance Certification – Secure Software Programmer – .NET He is the owner of Utah VoIP Store at http://www.utahvoipstore.com/ and SWS Development at http://www.swsdev.com/ and publishes windows apps under the name Blue Voice.

  Read the article

• pfSense Firewall or Linsys/Cisco router for small offices

  - by Tim Meers

  I'm about to start switching some networks around for multiple small offices. Each office has about 10 to 15 users and 10 to 15 computers. Each office has a spread of generic routers and access points. The routers vary from being used as routers, to just being an access point for wireless. Nothing formal has really ever beem implemented for each of the 10 offices. What I'm wanting is to set up a pfSense box for each office to configure things like: traffic shaping (for VoIP QOS) URL Filtering DHCP static routing multiple VLANs I'll then use some of the existing hardware for wireless. Maybe even integrate the wireless right into the firewall depending on the office layout. So my question, would this be better to do a full blown firewall box, or but a new business class or high end consumer class Linksys router to do the URL filtering, QOS and DHPC? Each option could allow for remote access and VPN for remote maintnance and each would only cost a nominal about of money for something decent, i.e. under $250.

  Read the article

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• WRTU54G-TM router with 3rd party firmware; Can custom firmware include stock binary portions?

  - by dlamblin

  I've been doing a lot of reading online about the Linksys WRTU54G-TM router model that I now own. It seems getting a custom firmware onto it is not a problem. But no one is talking about retaining the Voip features (yet). So far they're all disappointed that it's not a SIP machine and used GSM over IPSec. Personally I don't care about using it with non-t-mobile. If I take the original firmware, shouldn't I be able to extract it, and it's SquashFS image, and then move all of the t-mobile specific binaries for enabling the calling features over to a custom firmware installation (maybe OpenWRT)? You might ask why, and the reason is, that if I do this I could retain my calling features, which I do want, and ssh to the router and use it to run additional software, as any OpenWRT router could do. Does anyone know if this can be done, and how the firmware's binaries could be gotten at and installed correctly? Update I have found someone working on 3rd party WRTU54G-TM firmware. I am still interested in my second part of the questions, that is can't the stock firmware images be pulled apart and have the close-source, if any, binary kernel modules moved into another more flexible custom firmware?

  Read the article

• What's the best way to telnet from a remote Windows PC without using RDP?

  - by Rob D.

  Three Networks: 10.1.1.0 - Mine 172.1.1.0 - My Branch Office 172.2.2.0 - My Branch Office's VOIP VLAN. My PC is on 10.1.1.0. I need to telnet into a Cisco router on 172.2.2.0. The 10.1.1.0 network has no routes to 172.2.2.0, but a VPN connects 10.1.1.0 to 172.1.1.0. Traffic on 172.1.1.0 can route to 172.2.2.0. All PCs on 172.1.1.0 are running Windows XP. Without disrupting anyone using those PCs, I want to open a telnet session from one of those PCs to the router on 172.2.2.0. I've tried the following: psexec.exe \\branchpc telnet 172.2.2.1 psexec.exe \\branchpc cmd.exe telnet 172.2.2.1 psexec.exe \\branchpc -c plink -telnet 172.2.2.1 Methods 1 and 2 both failed because telnet.exe is not usable over psexec. Method 3 actually succeeded in creating the connection, but I cannot login because the session registers my carriage return twice. My password is always blank because at the "Username:" prompt I'm effectively typing: Routeruser[ENTER][ENTER] It's probably time to deploy WinRM... Does anyone know of any other alternatives? Does anyone know how I can fix plink.exe so it only receives one carriage return when I use it over psexec?

  Read the article

• Terminal server performance over high latency links

  - by holz

  Our datacenter and head office is currently in Brisbane, Australia, and we have a branch office in the UK. We have a private WAN with a 768k link to our UK office and the latency is at about 350ms. The terminal server performance is reeeeealy bad. Applications that don't have too much animation or any images seem to be okay. But as soon as they do, the session is almost unusable. Powerpoint and internet explorer are good examples of apps that make it run slow. And if there is an image in your email signature, outlook will hang for about 10 seconds each time a new line is inserted, while the image gets moved down a few pixels. We are currently running server 2003. I have tried Server 2008 R2 RDS, and also a third party solution called Blaze by a company called Ericom, but it is still not too much better. We currently have a 5 levels dynamic class of service with the priority in the following order. VoIP Video Terminal Services Printing Everything else When testing the terminal server performance, the link monitored using net-flows, and have plenty we of bandwidth available, so I believe that it is a latency issue rather than bandwidth. Is there anything that can be done to improve performance. Would citrix help at all?

  Read the article

• Domino to Exchange 2007 (or 2010) Design Concerns?

  - by NickToyota

  Today we got the executive green light to proceed with changing from a Domino platform to Exchange. The business prefers Exchange for a messaging platform. (even though IMO IBM Domino is fine - if it aint broke, don't fix it but it was not my call). I have been put in charge of Domino to Exchange process goes smoothly as possible. I have also been told to put together costs for this project. I have some questions and concerns re: network design, licensing, costs: The current setup is as follows. 1 HQ office (100 users), 1 secondary office (50 users), 5 branch offices (under 10 users). 5 different email domains Windows Server 2003 functional level with a few 2008 R2 Servers Lotus Domino Notes Servers (one in each office) Ironmail Appliance Public Domino Web Mail server Majority G5+ Proliant Servers Domino Blackberry Enterprise license and server No VoIP phones What are the basic hardware requirements for Exchange 2007 or 2010? Can I simply purchase a single physical server? Will each office require an Exchange server or possibly additional servers (roles)? How is email routed to the smaller branch offices? Standard or Enterprise licenses? The business has been running Domino (messaging and application services) for over 10 years and also want Exchange to support email services, Blackberry, Outlook Web Access, possibly support for iPhone devices. Thank you Serverfault universe.

  Read the article

• WRTU54G-TM router with 3rd party firmware; Can custom firmware include stock binary portions?

  - by dlamblin

  I've been doing a lot of reading online about the Linksys WRTU54G-TM router model that I now own. It seems getting a custom firmware onto it is not a problem. But no one is talking about retaining the Voip features (yet). So far they're all disappointed that it's not a SIP machine and used GSM over IPSec. Personally I don't care about using it with non-t-mobile. If I take the original firmware, shouldn't I be able to extract it, and it's SquashFS image, and then move all of the t-mobile specific binaries for enabling the calling features over to a custom firmware installation (maybe OpenWRT)? You might ask why, and the reason is, that if I do this I could retain my calling features, which I do want, and ssh to the router and use it to run additional software, as any OpenWRT router could do. Does anyone know if this can be done, and how the firmware's binaries could be gotten at and installed correctly? Update I have found someone working on 3rd party WRTU54G-TM firmware. I am still interested in my second part of the questions, that is can't the stock firmware images be pulled apart and have the close-source, if any, binary kernel modules moved into another more flexible custom firmware?

  Read the article

• Cisco QoS Guidance

  - by Kyle Brandt

  I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future. I do have VOIP at one location connected to this one over the Internet that goes through a VPN tunnel. Everything else that is between this location and other offices is on a separate MPLS network.

  Read the article

• Campus VLAN Segmentation - By OS?

  - by Moduspwnens

  We've been thinking through re-arranging our network and VLAN configuration. Here's the situation. We already have our servers, VoIP phones, and printers on their own VLANs, but our problem lies with end user devices. There are just too many to lump on the same VLAN without being hammered with broadcasts! Our current segmentation strategy has them split into VLANs like this: Student iPads Staff iPads Student Macbooks Staff Macbooks Gaming devices Staff (Other) Student (Other) *Note that our network has many more iPads and MacBooks than most. Since the primary reason we're splitting them is just to put them in smaller groups, this has been working for us (for the most part). However, this required our staff to maintain access control lists (MAC addresses) of all devices belonging in these groups. It also has the unfortunate side effect of illogically grouping broadcast traffic. For example, using this setup, students on opposite ends of campus using iPads will share broadcasts, but two devices belonging to the same user (in the same room) will likely be on completely separate VLANs. I feel like there must be a better way of doing this. I've done a lot of research and I'm having trouble finding instances of this kind of segmentation being recommended. The feedback on the most relevant SO question seems to point toward VLAN segmentation by building/physical location. I feel like that makes sense because logically, at least among miscellaneous end users, broadcasts will typically be intended for nearby devices. Are there other campuses/large-scale networks out there segmenting VLANs based on end-system OS? Is this a typical configuration? Would VLAN segmentation based on physical location (or some other criteria) be more effective? EDIT: I've been told that we will soon be able to dynamically determine device OS without maintaining access lists, although I'm not sure how much that affects the answers to the questions.

  Read the article

• Sharing files between 2 different routers

  - by Chris

  I realize this has been asked before and I have read as much as I could find on the topic but I still need help with this because there are so many different approaches and the ones I am trying aren't working. So I have 2 routers, lets call them A and B. Both have a wireless feature and are active. A is in the basement and receives the internet. There is a TV on the ground floor that is connected to A through an ethernet wire. B is upstairs and gets the internet from A through an ethernet wire. Connected to B, is a desktop running Plex Media Server. What I want to do is make sure devices connected to both routes can access the Plex Media Server. So what I have read is that I should plug in the ethernet wire connecting B to a into a LAN port instead of the WAN port. After that I should turn off DHCP. I have tried this and B stops receiving internet. What am I doing wrong? Another thing I have read is to use Router B in bridge mode but Router B is running openwrt and I have QoS on it so gaming/VoIP/browsing is unaffected by heavy downloading/uploading. I would prefer to keep this active. I realize it might be ineffective if a device in Router A is doing some hardcore downloading but all that stuff is done on Router B anyway so it doesn't matter. Router A can't get openwrt because it is a shitty one provided by Bell. So, how do I proceed with this?

  Read the article

• Using modem for sending voice recording

  - by ircmaxell

  I've got an interesting one for you. I've been going over my server monitoring and notification systems (Nagios based), and realized that if our internet connection goes down, there's no way for it to notify me. I already have a modem listening (Via CentOS 5) on a spare POTS line so that I can dial-in in case our internet goes down. I was wondering if I could come up with a script (Shell, Python, etc) that can dial out and play a recorded message (wave file I'm guessing) when it's picked up. I know Windows supports voice calls over a voice modem, I was wondering if a solution existed for Linux... I know asterisk can probably do it, but isn't that overkill (A full blown VOIP system just for a notification mechanism that will hopefully never be used)? And wouldn't it interfere with the modem's primary function as a backup network interface (PPP spawned via mgetty)? I've done some searching, and haven't really come up with much. I know how to dial out from the command line, but only as a modem (not as voice). Worst case, I could set it up to dial out as a modem, and then just realize that if I get a call with modem sounds from that number that it's the notification... Any insight would be appreciated...

  Read the article

• How do I setup routing for 2 companies with different Internet connections on the same LAN?

  - by Clint Miller

  Here's the setup: 2 companies (A & B) share office space and a LAN. A 2nd ISP is brought in and company A wants it's own Internet connection (ISP A) and company B wants it's own Internet connection (ISP B). VLANs are deployed internally to separate the 2 company's networks (company A: VLAN 1, company B: VLAN 2, shared VOIP: VLAN 3). With separate VLANs it's simple enough to use separate DHCP servers (or separate scopes on the same server) to assign the default gateway to each company's gateway for their Internet connection. Static routes can be created on each gateway to point traffic destined for the other company's VLAN or the voice VLAN so that all nodes are reachable as expected. However, I think this is a form of asymmetrical routing, right? (The path from node A1 to node B1 is not the same as the path back from node B1 to node A1). Can I setup policy-based routing to correct this? In that case, can I assign the same default gateway to every device on all VLANs and create a routing policy on a L3 switch to look at the source address and forward traffic to the appropriate next hop? In that case, I want the routing logic to go like this: If the destination address is known, forward the traffic (traffic destined for a different VLAN). If the destination address is unknown, forward the traffic to ISP A's gateway if the source address is on VLAN A; or forward the traffic to ISP B's gateway if the source address is VLAN B. Am I thinking about this problem in the correct way? Is there another way to solve this problem that I am overlooking?

  Read the article

• Using a Level 2 switch as a core switch

  - by imtech

  I have a small user base of about 20 people on at a time and spiking up to about 80 people during peak times. Most people (80+%) are connected over our Aruba managed wireless system. We have a Windows Domain. We have 3 24-Port switches all connecting back to a central 48-port switch where additional access ports, firewall, servers, and wireless controller all centrally connect back to. It's a flat network with dumb switches. I'm in the process of upgrading our infrastructure. Cisco pricing for switches is pretty high for us so I've been looking at HP Procurves which seem to be within our budget range. I want to eventually make use of 802.1x, SNMP, QoS for possible VOIP upgrades, VLAN to separate guest VLAN from authenticated users, and other more advanced features. PoE would be nice but that's probably too expensive for us. I was thinking of having our core switch be a Procurve 2610 and the rest of our switches that centrally connect to it be Procurve 2510s. A true and full blown level 3 switch is way out of our price range but a 2610 seems to be good enough for us. The 2610 does static routing which ought to be good enough for us but I'm in unfamiliar territory so I'm looking for any gotchas. Also, should all the switches be 2610s or just the core switch? Do I even need the 2610, can I just go with all 2510s? I'm new to VLANs as well so I'm not sure what it is I need but I would like an affordable infrastructure that won't need replacing 2-3 years down the line because I choose a product that was lacking.

  Read the article

• Router not connecting to the internet

  - by Peter

  I had a weird problem this morning with my router - it's an Alice Gate VoIP 2 Plus WI-FI - not connecting to the internet after more or less 1 hour online (I'm always connected with the ethernet cable). The led status lights for Power, WI-FI, ADSL, Internet, Service should be on in order to be connected and navigate online. The problem was that the leds ADSL, Internet were off and I did not know why because it never happened before. I looked at the stats in the settings and the numbers for Bytes/Packages for both Sent/Received were there and increasing but I couldn't connect to the internet. I called tech support, they checked and told me to keep the router on for 48 hours because they were checking it. I've reset it twice before and after I called tech support and it still did not work so after about 2 hours of waiting I tried connecting using WI-FI and the leds 'magically' turned on, first the ADSL and Internet(Internet led always turns on last). At this point I'm curious what could of caused this and I'm doubting that the tech-support guys did something. What could of been the problem with the ethernet cable not connecting in the first place? It always works. What do the tech support guys normally do when they tell me to keep the router on so they can 'check it'? PS: I'm using ubuntu 32 bit

  Read the article

• What's the best way to telnet from a remote Windows PC without using RDP?

  - by Rob D.

  Three Networks: 10.1.1.0 - Mine 172.1.1.0 - My Branch Office 172.2.2.0 - My Branch Office's VOIP VLAN. My PC is on 10.1.1.0. I need to telnet into a Cisco router on 172.2.2.0. The 10.1.1.0 network has no routes to 172.2.2.0, but a VPN connects 10.1.1.0 to 172.1.1.0. Traffic on 172.1.1.0 can route to 172.2.2.0. All PCs on 172.1.1.0 are running Windows XP. Without disrupting anyone using those PCs, I want to open a telnet session from one of those PCs to the router on 172.2.2.0. I've tried the following: psexec.exe \\branchpc telnet 172.2.2.1 psexec.exe \\branchpc cmd.exe telnet 172.2.2.1 psexec.exe \\branchpc -c plink -telnet 172.2.2.1 Methods 1 and 2 both failed because telnet.exe is not usable over psexec. Method 3 actually succeeded in creating the connection, but I cannot login because the session registers my carriage return twice. My password is always blank because at the "Username:" prompt I'm effectively typing: Routeruser[ENTER][ENTER] It's probably time to deploy WinRM... Does anyone know of any other alternatives? Does anyone know how I can fix plink.exe so it only receives one carriage return when I use it over psexec?

  Read the article

• DD-WRT Acces Point as a Router

  - by Dzh

  Following suggestion to this question asked on Network Engineering, I am asking the question here. this is an extension to my previous question (I think it was deleted), where I was claiming that DDWRT was disabling it's DHCP server once connected to the network. I was wrong, as it now seems that it is bridging itself with another parallel connected wireless router. I have two Draytek 2820 and one Netgear WG602v3 with latest DDWRT. Lets call one wired-Draytek and it has wireless disabled. The other one, let's call it wireless-Draytek, is connected to wired-Draytek and has wireless with MAC filtering enabled. Once I connect Netgear to the wired-Draytek, the client that connects to Netgear, will be assigned with IP address from the wireless-Draytek. If the MAC address is not on the wireles-Draytek, the client is unable to obtain IP address and has no connectivity at all, even with manually assigned static IP configuration. To illustrate further, this is how network is set up: wired-Draytek ---------- wireless-Draytek \_________ Netgear What I wish to have, is that Netgear issues IP addresses from it's own IP pool and ignores the MAC filtering rules from wireless-Draytek. This is kind of puzzling how this they are bridging (if they are) themselves automatically. Thanks. UPDATE: It's not a home network. I gave you a bit simplified set-up. If there is a better site on Stack Exchange to ask this, please let me know. The Drayteks are running stock firmware, it's only Netgear that I've flashed to get more stability. In addition to these routers, I have also three 3COM Baseline switch 2824, and another Draytek router with Prosafe FS752TP PoE switch dedicated for VoIP phones. Wired-Draytek has IP 10.0.0.1, DHCP disabled as there is AD DC which is issuing IP addresses. Wireless-Draytek has IP 1.1.1.1 and DHCP enabled. Netgear has default - 192.168.1.1. As per suggestion, the specific question is - how do I isolate these two wireless routers?

  Read the article

< Previous Page | 11 12 13 14 15 16 17  | Next Page >