Search Results

Search found 5769 results on 231 pages for 'wcf routing'.

Page 15/231 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

  • Windows server 2008R2 routing with single NIC

    - by Fabian
    I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

    Read the article

  • Windows server 2008R2 routing with single NIC

    - by Fabian
    I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

    Read the article

  • IPv6 Routing / Subnetting

    - by nappo
    Recently I have installed Citrix Xen Server 6.2 on a machine. My Provider (Hetzner) gave me the IPv6 Subnet 2a01:4f8:200:xxxx::/64. Followed an article in the providers wiki (1) i got it working and can assign IPs to my guests (CentOS). However i can't assign a second IP to a single guest - it will result in a timeout. I'm not very familiar with IPv6 routing / subnetting - any help or tips for further troubleshooting is welcome! My Setup: XenServer 6.2 IPv6: 2a01:4f8:200:xxxx::2/112 ip -6 route: 2a01:4f8:200:xxxx::/112 dev xenbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 default via fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 Guest 1 IPv6: 2a01:4f8:200:xxxx::3/64 IPv6: 2a01:4f8:200:xxxx::4/64 ip -6 route: 2a01:4f8:200:xxxx::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::1 dev eth0 metric 1 mtu 1500 advmss 1440 hoplimit 4294967295 Guest 2 IPv6: 2a01:4f8:200:xxxx::5/64 Guest 1 IPv6 is working fine, Guest 2 too. As suggested by the wiki article (1) i split my /64 network into a /112. Is it right to set the host /112 and the guests /64? Why is that?

    Read the article

  • Problem routing between directly connected Subnets w/ ASA-5510

    - by Zephyr Pellerin
    This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

    Read the article

  • Help with routing table

    - by user68752
    I have tried to find the answer to my question but not really found a clean and easy solution. I have a box (Ubuntu headless 10.04.1 server, with one Ethernet port) on LAN behind a router (running m0n0wall), that I have successfully installed a PPTP device (ppp0) on, this is working flawlessly (following this link) The thing is I want this box to route all it's internet traffic through the VPN tunnel (ppp0 device) but also being able to access the local LAN on 192.168.1.* subnet. I've succeeded a bit with this, but my problem right now is that I have port forwards (e.g. SSH) done in the m0n0wall pointing to this specific box which forces me to do "add routes" to all boxes that want to access this machine through this specific port. For instance a machine with ip xyz.xyz.xyz.xyz needs to have a static route setup in the routing table on the box to be able to access the box. This is the result of route -n xxx.xxx.137.2 192.168.1.1 255.255.255.255 UGH 0 0 0 eth0 xxx.xxx.137.2 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 yyy.yyy.0.0 192.168.1.1 255.255.0.0 UG 0 0 0 eth0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 Where xxx is the IPs provided from VPN server. yyy.yyy.0.0 is a net that i want to have access to the box, without this I can't access the box from outside the LAN (via port-forwards done in router software, m0n0wall) is there away round this ugly solution?

    Read the article

  • Different subnets routing with just one layer 3 switch

    - by GustavoFSx
    Our current network looks like this: Location 1: 2 Layer 2 switches | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | Firewall for our VPN Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN We just got a direct fiber connection between location 1 and 2, we also got a new HP V1910 24G layer 3 switch. I tried to follow the instructions on this site, but I can't get it to work. I think our network should look like this: Location 1: HP Switch FIBER to L2 | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | FIBER to L1 Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN So, how can I get routing working on our location 2? It's old gateway was a firewall device on ip 192.168.3.1. I'm thinking on creating a VLAN Interface on 192.168.3.1 on the switch for the Location 2. But how will I handle that on the HP switch that has a direct fiber connection with that switch? Please help, I'm not very good with networking.

    Read the article

  • Does WCF always use SOAP to send information over your binding?

    - by SLC
    I understand you can choose from a range of bindings, such as TCP, HTTP, HTTPS etc. Am I correct in thinking it always uses SOAP to send data over this connection? I am watching a guide to WCF and it is talking about how exceptions are serialized into SOAP and sent to the client. I would have thought that not all bindings would use SOAP to send data, so I am a bit confused about how it works. Although I understand the fundamentals of WCF, how to set up services and use a proxy on the client, it doesn't seem to have explained exactly how the data is packaged up to send. Perhaps the answer is obvious, that it just uses XML / SOAP, but I would love to know for sure!

    Read the article

  • Mikrotik and NAT/Routing issue

    - by arul
    I have basic NAT/Routing problem with Mikrotik RB750 that I've been unable to solve over the past days. From our ISP we have 26 IP addresses: 10.10.10.192/27, with 10.10.10.193 being the gateway and 10.10.10.194 the first available IP. What I need is that everything connected to ether2 gets a public IP from the DHCP server, and everything connected to ether3 gets a local IP from another DHCP (192.168.100.0/24). All clients should have internet access (I'll figure out bandwidth throttling later) and optimally just 'see' each other (all boxes are Win7, I guess this can ultimately be handled with VPN). Here is my setup: ether1 (10.10.10.194) is connected directly to ISP. 20 clients connected to ether2(10.10.10.195), and another 20 to ether3(10.10.10.196) (both through same 24 port switches). This is my setup, which doesn't work, all 20 clients from ether2 can access the internet, though all comm. seems to come from 10.10.10.194 (is this due to the masquerade on ether1?), and ether3 can't access the internet at all. I think that I need to masquerade ether3, and SNAT/DNAT or NETMAP ether2, but that doesn't work either, I guess that I need to somehow 'wire' both ether2+3 to ether1. Address list: # ADDRESS NETWORK INTERFACE 0 ;;; public 10.10.10.194/32 10.10.10.192 ether1-gateway 1 ;;; inner DHCP 192.168.100.0/24 192.168.100.0 ether3-private 2 ;;; public 10.10.10.195/32 10.10.10.192 ether2-pub 3 ;;; public 10.10.10.196/32 10.10.10.192 ether3-private NAT 0 ;;; ether3 nat chain=srcnat action=src-nat to-addresses=10.10.10.196 src-address=192.168.100.0/24 out-interface=ether3-private 1 ;;; ether3 nat chain=dstnat action=dst-nat to-addresses=192.168.100.0/24 in-interface=ether3-private 2 ;;; ether1 masquerade chain=srcnat action=masquerade to-addresses=10.10.10.194 out-interface=ether1-gateway Routes: # DST-ADDRESS PREF-SRC GATEWAY DISTANCE 0 A S 0.0.0.0/0 ether1-gateway 1 2 A S 10.10.10.192/27 10.10.10.195 ether2-pub 1 3 ADC 10.10.10.192/32 10.10.10.195 ether2-pub 0 ether1-gateway ether3-private 4 ADC 192.168.100.0/24 192.168.100.0 ether3-private 0 IP Pools: # NAME RANGES 0 public-pool 10.10.10.201-10.10.10.220 1 private-pool 192.168.100.2-192.168.100.254 DHCP configs: # NAME INTERFACE RELAY ADDRESS-POOL LEASE-TIME ADD-ARP 0 public-dhcp ether2-pub public-pool 3d 1 private-dhcp ether3-private private-pool 3d Thanks!

    Read the article

  • Routing a PPTP client and VMware Server instance running on the same box

    - by servermanfail
    I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

    Read the article

  • Routing RFC1918 addresses through dd-wrt via a switch

    - by espenfjo
    I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

    Read the article

  • Virtualbox - routing subnet to bridge adapters

    - by user42384
    Hello, I have set up a Debian Lenny box with 3 vbox Lenny machines running eth0 of the host in bridged mode (on virtualbox 3.1.6). When testing in my local LAN, this all worked perfectly well and traffic flowed to and from the IPs of the virtual machines as it should. However, now that it's in its co-lo home, the networking setup is a bit different, and I'm unable to get traffic to flow to the vboxes properly. Specifically, the host has its own Primary IP, and I have a separate subnet of 8 (6 usable) IPs routed to the box for use by the vboxes. So, eth0 on host is: Machine IP: 2x.x.x.137 Gateway IP: 2x.x.x.138 Subnet Msk: 255.255.255.252 Subnet for vboxes is Subnet: 2x.x.x.240/29 Netmask: 255.255.255.248 vbox1 is configured to 2x.x.x.241 on eth0 as follows: auto eth0 iface eth0 inet static address 2x.x.x.241 netmask 255.255.255.248 Setting up a virtual interface (eth0:0) on the host with one of these subnet IPs allows me to ping to that address only from vbox1, and it allows me to ping vbox1 from the host. I can also ping that virtual interface perfectly well from outside, so the IPs are definitely landing at my machine. It seems I'm missing some sort of routing instruction either on the host or vbox1 to get traffic moving between the subnet and the default gateway, but I can't seem to figure out what it should be, or what glaringly obvious thing i'm missing. Most of my obvious attempts (the gw of eth0, the ip of eth0) were rejected by route command with SIOCADDRT: No such device (eg - i can't find it). I tried setting vbox1 to bridge on eth0:0, but this was not an acceptable device name and VBoxHeadless refused to start. The physical machine does have an unused physical NIC at eth1 that can be used if necessary for something or other. Host machine is running iptables configured by ferm, have experimented with it allowing forwarding for that subnet, but I wouldn't have thought this was necessary given the nature of the virtualbox devices (nor did it actually work). Clearing out all of these rules for a blank iptables set does not resolve the issue. (you can see ferm generated iptables at http://codedumper.com/ojaze) Thanks for any help you can give... Patrick

    Read the article

  • routing specific IP to ppp0 tunnel

    - by gompertz
    Hi All, I feel I've struggled with this long enough and need some help. I have a pptp tunnel and am trying to route destination traffic from 208.85.40.20 to the pptp tunnel (ppp0). (Keen observers may recognize the ip as being that of pandora.com). I am doing all this configuration on a router... and I know it's not working successfully as traceroute yields nothing but astericks. I've pasted relevant outputs below: (with some "security" editing to the addresses) root@OpenWrt:~# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28185 errors:0 dropped:0 overruns:0 frame:0 TX packets:24936 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4894242 (4.6 MiB) TX bytes:5941902 (5.6 MiB) eth0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:51829 errors:0 dropped:0 overruns:0 frame:0 TX packets:56824 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11490288 (10.9 MiB) TX bytes:11857913 (11.3 MiB) Interrupt:4 eth2 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:15426 TX packets:9529 errors:21 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:423 (423.0 B) TX bytes:596036 (582.0 KiB) Interrupt:2 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:30 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2300 (2.2 KiB) TX bytes:2300 (2.2 KiB) ppp0 Link encap:Point-Point Protocol inet addr:68.68.39.250 P-t-P:172.16.20.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:165 errors:2 dropped:0 overruns:0 frame:0 TX packets:68 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:7006 (6.8 KiB) TX bytes:3462 (3.3 KiB) vlan0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:28182 errors:0 dropped:0 overruns:0 frame:0 TX packets:33813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5006544 (4.7 MiB) TX bytes:6609774 (6.3 MiB) vlan1 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:173.183.111.3 Bcast:173.183.111.255 Mask:255.255.224.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23653 errors:0 dropped:0 overruns:0 frame:0 TX packets:23012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5522012 (5.2 MiB) TX bytes:4982944 (4.7 MiB) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@OpenWrt:~# cat /etc/ppp/ip-up iptables -A FORWARD -t filter -i br0 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -t filter -i ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -s 192.168.1.1/24 -d 0/0 -j MASQUERADE iptables -A forwarding_rule -o ppp0 -j ACCEPT iptables -A forwarding_rule -i ppp0 -j ACCEPT iptables -t nat -A postrouting_rule -o ppp0 -j MASQUERADE root@OpenWrt:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.20.1 * 255.255.255.255 UH 0 0 0 ppp0 208.85.40.20 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 173.183.192.0 * 255.255.224.0 U 0 0 0 vlan1 default d173-183-192-1. 0.0.0.0 UG 0 0 0 vlan1 default 192.168.1.1 0.0.0.0 UG 0 0 0 br0 Any advice is greatly appreciated, I'm not too great with network but am pretty astute at learning ;-)

    Read the article

  • Linux IPTables / routing issue

    - by Jon
    Hi all, EDIT 1/3/10 22:00 GMT - rewrote some of it after further investigation It has been a while since I looked at IPtables and I seem to be worse than before as I can not seem to get my webserver online. Below is my firewall rules on the gateway server that is running the dhcp server accessing the net. The webserver is inside my network on a static IP (192.168.0.98, default port). When I use Nmap or GRC.com I see that port 80 is open on the gateway server but when I browse to it, (via public URL. http://www.houseofhawkins.com) it always fails with a connection error, (nmap cannot connect and figure out what the web server is either). I can nmap the webserver and browse to it just fine via same IP inside my network. I believe it is my IPTable rules that are not letting it through. Internally I can route all my requests. Each machine can browse to the website and traffic works just fine. I can MSTSC / ssh to all the webservers internally and they inturn can connect to the web. IPTABLE: *EDIT - Added new firewall rules 2/3/10 * #!/bin/sh iptables="/sbin/iptables" modprobe="/sbin/modprobe" depmod="/sbin/depmod" EXTIF="eth2" INTIF="eth1" load () { $depmod -a $modprobe ip_tables $modprobe ip_conntrack $modprobe ip_conntrack_ftp $modprobe ip_conntrack_irc $modprobe iptable_nat $modprobe ip_nat_ftp echo "enable forwarding.." echo "1" > /proc/sys/net/ipv4/ip_forward echo "enable dynamic addr" echo "1" > /proc/sys/net/ipv4/ip_dynaddr # start firewall # default policies $iptables -P INPUT DROP $iptables -F INPUT $iptables -P OUTPUT DROP $iptables -F OUTPUT $iptables -P FORWARD DROP $iptables -F FORWARD $iptables -t nat -F #echo " Opening loopback interface for socket based services." $iptables -A INPUT -i lo -j ACCEPT $iptables -A OUTPUT -o lo -j ACCEPT #echo " Allow all connections OUT and only existing and related ones IN" $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A OUTPUT -o $EXTIF -j ACCEPT $iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $EXTIF -o $INTIF -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $INTIF -o $EXTIF -j ACCEPT $iptables -A FORWARD -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A INPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A OUTPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " #echo " Enabling SNAT (MASQUERADE) functionality on $EXTIF" $iptables -t nat -A POSTROUTING -o $EXTIF -j MASQUERADE $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A OUTPUT -o $INTIF -j ACCEPT #echo " Allowing packets with ICMP data (i.e. ping)." $iptables -A INPUT -p icmp -j ACCEPT $iptables -A OUTPUT -p icmp -j ACCEPT $iptables -A INPUT -p udp -i $INTIF --dport 67 -m state --state NEW -j ACCEPT #echo " Port 137 is for NetBIOS." $iptables -A INPUT -i $INTIF -p udp --dport 137 -j ACCEPT $iptables -A OUTPUT -o $INTIF -p udp --dport 137 -j ACCEPT #echo " Opening port 53 for DNS queries." $iptables -A INPUT -p udp -i $EXTIF --sport 53 -j ACCEPT #echo " opening Apache webserver" $iptables -A PREROUTING -t nat -i $EXTIF -p tcp --dport 80 -j DNAT --to 192.168.0.96:80 $iptables -A FORWARD -p tcp -m state --state NEW -d 192.168.0.96 --dport 80 -j ACCEPT } flush () { echo "flushing rules..." $iptables -P FORWARD ACCEPT $iptables -F INPUT $iptables -P INPUT ACCEPT echo "rules flushed" } case "$1" in start|restart) flush load ;; stop) flush ;; *) echo "usage: start|stop|restart." ;; esac exit 0 route info: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 5e0412a6.bb.sky * 255.255.255.255 UH 0 0 0 eth2 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 default 5e0412a6.bb.sky 0.0.0.0 UG 100 0 0 eth2 ifconfig: eth1 Link encap:Ethernet HWaddr 00:22:b0:cf:4a:1c inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:b0ff:fecf:4a1c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:79023 errors:0 dropped:0 overruns:0 frame:0 TX packets:57786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11580918 (11.5 MB) TX bytes:22872030 (22.8 MB) Interrupt:17 Base address:0x2b00 eth2 Link encap:Ethernet HWaddr 00:0c:f1:7c:45:5b inet addr:94.4.18.166 Bcast:94.4.18.166 Mask:255.255.255.255 inet6 addr: fe80::20c:f1ff:fe7c:455b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57038 errors:0 dropped:0 overruns:0 frame:0 TX packets:34532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21631721 (21.6 MB) TX bytes:7685444 (7.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1517 (1.5 KB) TX bytes:1517 (1.5 KB) EDIT OK so as requested I will try and expand on my infrastructure: I previously had it setup with a Sky broadband modem router that did the DHCP and I used its web interface to port forward the web across to the web server. The network looked something like this: I have now replaced the sky modem with a dlink modem which gives the IP to the gateway server that now does the DHCP. It looks like: The internet connection is a standard broadband connection with a dynamic IP, (use zoneedit.com to keep it updated). I have tried it on each of the webservers(one Ubuntu Apache server and one WS2008 IIS7). I think there must also be an issue with my IPTable rules as it can route to my win7 box which has the default IIS7 page and that would not display when I forwarded all port 80 to it. I would be really grateful for any and all help with this. Thanks Jon

    Read the article

  • Linq to SQl over WCF Timesout after several calls

    - by Redeemed1
    I have a L2S Repository class which instantiates the L2S DataContext in its constructor. The repository is instantiated at run time (using Unity) in a service hosted in IIS with WCF. When I run up the client MVC applicaton the calls to the backend WCF service work for a while and then timeout. I suspected perhaps a database issue as I was depending on IIS garbage collection to dispose of unused DataContext instances in the IIS host but when I checked the characteristics of the problem I notice the following: The client makes the call to WCF but the WCF service does not respond. Next, the client times out Some time later (several minutes) the service actually executes the request by instantiating the repository and servicing the call. I have checked both client and server traces logs and only the client shows WCF errors (the timeout error). Where should I look? Is it something in WCF or is L2S possibly blocking with unfreed conenctions, resources etc.? Many thanks Brian

    Read the article

  • WCF - Compact Framework - Pull data from mobile client

    - by jagse
    Hello guys, I want to communicate xml serialized objects from the server to the client and the other way arround. Now it is (probably) easy to invoke methods from a mobile client (compact framework) using WCF, but is there a way so that the server can invoke methods on the client side or some other way to pull data from the client? I know that callback contracts are not available in the compact framework as you can see here: http://blogs.msdn.com/andrewarnottms/archive/2007/09/13/calling-wcf-services-from-netcf-3-5-using-compact-wcf-and-netcfsvcutil-exe.aspx Originally I thought of socket programming and of developing this by myself, then someone here mentioned WCF. But it seems like WCF only would work in a non mobile environment as I need callbacks. Anyone can help me with this? Is it possible to develop a two way communication with a desktop server and multiple mobile clients using WCF, or will I have to do socket programming? Thanks for any advice or any kind of help!

    Read the article

  • WCF port routing

    - by C james
    I have NAT which received incoming WCF requests and changes port number before it hands off to the host however, this is causing problem is there anyway to turn this off or fix? ex) wcf.service.com:80 - NAT - wcf.service.2522 !error Thank you.

    Read the article

  • Using IIS Application Request Routing (ARR) for ASP.NET MVC

    - by Malcolm Frexner
    I use a simple ASP.NET MVC web (the template you use when you create a new site) and the web works as expected in my live environment. I now try to use IIS Application Request Routing version 2. I have a rule that send all reuqests to a different server that match a rule. The settings are a bit like this: http://blogs.iis.net/wonyoo/archive/2008/07/09/application-request-routing-arr-as-a-reverse-proxy.aspx My rule is just a bit different it is /shop(.*). Only requests that contain shop are send to a different server. I have to use rewrite, not redirect (The same as in the Picture) This works as long as the web the original requests go to is no ASP.NET MVC web. I tried to use a plain htm file in the webfolder and it worked. If put a compiled ASP.NET application into the webfolder it worked. But as soon as I put an ASP.NET MVC web into the folder, request arr served by this application. My understanding is that the ARR should kick in before the web application gets the chance to handle the request. Did anybody use ARR sucessfully as a reverse proxy for a ASP.NET MVC web? EDIT Here is the resulting web config when the rewrite roule is entered. With this rule I get a 404 that indicates that the rule is not used. <?xml version="1.0" encoding="UTF-8"?> <configuration> <configSections> <sectionGroup name="system.web.extensions" type="System.Web.Configuration.SystemWebExtensionsSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <sectionGroup name="scripting" type="System.Web.Configuration.ScriptingSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <sectionGroup name="webServices" type="System.Web.Configuration.ScriptingWebServicesSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="Everywhere" /> <section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="roleService" type="System.Web.Configuration.ScriptingRoleServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> </sectionGroup> </sectionGroup> </sectionGroup> </configSections> <appSettings /> <connectionStrings> <add name="ApplicationServices" connectionString="data source=.\SQLEXPRESS;Integrated Security=SSPI;AttachDBFilename=|DataDirectory|aspnetdb.mdf;User Instance=true" providerName="System.Data.SqlClient" /> </connectionStrings> <system.web> <!-- Set compilation debug="true" to insert debugging symbols into the compiled page. Because this affects performance, set this value to true only during development. --> <compilation debug="false"> <assemblies> <add assembly="System.Core, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Web.Abstractions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Web.Routing, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Data.DataSetExtensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Xml.Linq, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Data.Linq, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> </assemblies> </compilation> <!-- The <authentication> section enables configuration of the security authentication mode used by ASP.NET to identify an incoming user. --> <authentication mode="Forms"> <forms loginUrl="~/Account/LogOn" timeout="2880" /> </authentication> <membership> <providers> <clear /> <add name="AspNetSqlMembershipProvider" type="System.Web.Security.SqlMembershipProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" connectionStringName="ApplicationServices" enablePasswordRetrieval="false" enablePasswordReset="true" requiresQuestionAndAnswer="false" requiresUniqueEmail="false" passwordFormat="Hashed" maxInvalidPasswordAttempts="5" minRequiredPasswordLength="6" minRequiredNonalphanumericCharacters="0" passwordAttemptWindow="10" passwordStrengthRegularExpression="" applicationName="/" /> </providers> </membership> <profile> <providers> <clear /> <add name="AspNetSqlProfileProvider" type="System.Web.Profile.SqlProfileProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" connectionStringName="ApplicationServices" applicationName="/" /> </providers> </profile> <roleManager enabled="false"> <providers> <clear /> <add connectionStringName="ApplicationServices" applicationName="/" name="AspNetSqlRoleProvider" type="System.Web.Security.SqlRoleProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> <add applicationName="/" name="AspNetWindowsTokenRoleProvider" type="System.Web.Security.WindowsTokenRoleProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> </providers> </roleManager> <!-- The <customErrors> section enables configuration of what to do if/when an unhandled error occurs during the execution of a request. Specifically, it enables developers to configure html error pages to be displayed in place of a error stack trace. <customErrors mode="RemoteOnly" defaultRedirect="GenericErrorPage.htm"> <error statusCode="403" redirect="NoAccess.htm" /> <error statusCode="404" redirect="FileNotFound.htm" /> </customErrors> --> <pages> <controls> <add tagPrefix="asp" namespace="System.Web.UI" assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add tagPrefix="asp" namespace="System.Web.UI.WebControls" assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </controls> <namespaces> <add namespace="System.Web.Mvc" /> <add namespace="System.Web.Mvc.Ajax" /> <add namespace="System.Web.Mvc.Html" /> <add namespace="System.Web.Routing" /> <add namespace="System.Linq" /> <add namespace="System.Collections.Generic" /> </namespaces> </pages> <httpHandlers> <remove verb="*" path="*.asmx" /> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="*" path="*_AppService.axd" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" validate="false" /> <add verb="*" path="*.mvc" validate="false" type="System.Web.Mvc.MvcHttpHandler, System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </httpHandlers> <httpModules> <add name="ScriptModule" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="UrlRoutingModule" type="System.Web.Routing.UrlRoutingModule, System.Web.Routing, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </httpModules> </system.web> <system.codedom> <compilers> <compiler language="c#;cs;csharp" extension=".cs" warningLevel="4" type="Microsoft.CSharp.CSharpCodeProvider, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"> <providerOption name="CompilerVersion" value="v3.5" /> <providerOption name="WarnAsError" value="false" /> </compiler> <compiler language="vb;vbs;visualbasic;vbscript" extension=".vb" warningLevel="4" type="Microsoft.VisualBasic.VBCodeProvider, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"> <providerOption name="CompilerVersion" value="v3.5" /> <providerOption name="OptionInfer" value="true" /> <providerOption name="WarnAsError" value="false" /> </compiler> </compilers> </system.codedom> <system.web.extensions /> <!-- The system.webServer section is required for running ASP.NET AJAX under Internet Information Services 7.0. It is not necessary for previous version of IIS. --> <system.webServer> <rewrite> <rules> <rule name="shop" stopProcessing="true"> <match url="^shop/([_0-9a-z-.]+)" /> <action type="Rewrite" url="article.aspx?title={R:1}" logRewrittenUrl="true" /> </rule> </rules> </rewrite> <validation validateIntegratedModeConfiguration="false" /> <modules runAllManagedModulesForAllRequests="true"> <remove name="ScriptModule" /> <remove name="UrlRoutingModule" /> <add name="ScriptModule" preCondition="managedHandler" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="UrlRoutingModule" type="System.Web.Routing.UrlRoutingModule, System.Web.Routing, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </modules> <handlers> <remove name="WebServiceHandlerFactory-Integrated" /> <remove name="ScriptHandlerFactory" /> <remove name="ScriptHandlerFactoryAppServices" /> <remove name="ScriptResource" /> <remove name="MvcHttpHandler" /> <remove name="UrlRoutingHandler" /> <add name="ScriptHandlerFactory" verb="*" path="*.asmx" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptHandlerFactoryAppServices" verb="*" path="*_AppService.axd" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptResource" preCondition="integratedMode" verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="MvcHttpHandler" preCondition="integratedMode" verb="*" path="*.mvc" type="System.Web.Mvc.MvcHttpHandler, System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="UrlRoutingHandler" preCondition="integratedMode" verb="*" path="UrlRouting.axd" type="System.Web.HttpForbiddenHandler, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> </handlers> </system.webServer> </configuration>

    Read the article

  • Allowing Access to HttpContext in WCF REST Services

    - by Rick Strahl
    If you’re building WCF REST Services you may find that WCF’s OperationContext, which provides some amount of access to Http headers on inbound and outbound messages, is pretty limited in that it doesn’t provide access to everything and sometimes in a not so convenient manner. For example accessing query string parameters explicitly is pretty painful: [OperationContract] [WebGet] public string HelloWorld() { var properties = OperationContext.Current.IncomingMessageProperties; var property = properties[HttpRequestMessageProperty.Name] as HttpRequestMessageProperty; string queryString = property.QueryString; var name = StringUtils.GetUrlEncodedKey(queryString,"Name"); return "Hello World " + name; } And that doesn’t account for the logic in GetUrlEncodedKey to retrieve the querystring value. It’s a heck of a lot easier to just do this: [OperationContract] [WebGet] public string HelloWorld() { var name = HttpContext.Current.Request.QueryString["Name"] ?? string.Empty; return "Hello World " + name; } Ok, so if you follow the REST guidelines for WCF REST you shouldn’t have to rely on reading query string parameters manually but instead rely on routing logic, but you know what: WCF REST is a PITA anyway and anything to make things a little easier is welcome. To enable the second scenario there are a couple of steps that you have to take on your service implementation and the configuration file. Add aspNetCompatibiltyEnabled in web.config Fist you need to configure the hosting environment to support ASP.NET when running WCF Service requests. This ensures that the ASP.NET pipeline is fired up and configured for every incoming request. <system.serviceModel>     <serviceHostingEnvironment aspNetCompatibilityEnabled="true" multipleSiteBindingsEnabled="true" /> </system.serviceModel> Markup your Service Implementation with AspNetCompatibilityRequirements Attribute Next you have to mark up the Service Implementation – not the contract if you’re using a separate interface!!! – with the AspNetCompatibilityRequirements attribute: [ServiceContract(Namespace = "RateTestService")] [AspNetCompatibilityRequirements(RequirementsMode = AspNetCompatibilityRequirementsMode.Allowed)] public class RestRateTestProxyService Typically you’ll want to use Allowed as the preferred option. The other options are NotAllowed and Required. Allowed will let the service run if the web.config attribute is not set. Required has to have it set. All these settings determine whether an ASP.NET host AppDomain is used for requests. Once Allowed or Required has been set on the implemented class you can make use of the ASP.NET HttpContext object. When I allow for ASP.NET compatibility in my WCF services I typically add a property that exposes the Context and Request objects a little more conveniently: public HttpContext Context { get { return HttpContext.Current; } } public HttpRequest Request { get { return HttpContext.Current.Request; } } While you can also access the Response object and write raw data to it and manipulate headers THAT is probably not such a good idea as both your code and WCF will end up writing into the output stream. However it might be useful in some situations where you need to take over output generation completely and return something completely custom. Remember though that WCF REST DOES actually support that as well with Stream responses that essentially allow you to return any kind of data to the client so using Response should really never be necessary. Should you or shouldn’t you? WCF purists will tell you never to muck with the platform specific features or the underlying protocol, and if you can avoid it you definitely should avoid it. Querystring management in particular can be handled largely with Url Routing, but there are exceptions of course. Try to use what WCF natively provides – if possible as it makes the code more portable. For example, if you do enable ASP.NET Compatibility you won’t be able to self host a WCF REST service. At the same time realize that especially in WCF REST there are number of big holes or access to some features are a royal pain and so it’s not unreasonable to access the HttpContext directly especially if it’s only for read-only access. Since everything in REST works of URLS and the HTTP protocol more control and easier access to HTTP features is a key requirement to building flexible services. It looks like vNext of the WCF REST stuff will feature many improvements along these lines with much deeper native HTTP support that is often so useful in REST applications along with much more extensibility that allows for customization of the inputs and outputs as data goes through the request pipeline. I’m looking forward to this stuff as WCF REST as it exists today still is a royal pain (in fact I’m struggling with a mysterious version conflict/crashing error on my machine that I have not been able to resolve – grrrr…).© Rick Strahl, West Wind Technologies, 2005-2011Posted in ASP.NET  AJAX  WCF  

    Read the article

  • Is it possible to force the WCF test client to accept a self-signed certificate?

    - by Lawrence Johnston
    I have a WCF web service running in IIS 7 using a self-signed certificate (it's a proof of concept to make sure this is the route I want to go). It's required to use SSL. Is it possible to use the WCF Test Client to debug this service without needing a non-self-signed certificate? When I try I get this error: Error: Cannot obtain Metadata from https:///Service1.svc If this is a Windows (R) Communication Foundation service to which you have access, please check that you have enabled metadata publishing at the specified address. For help enabling metadata publishing, please refer to the MSDN documentation at http://go.microsoft.com/fwlink/?LinkId=65455.WS-Metadata Exchange Error URI: https:///Service1.svc Metadata contains a reference that cannot be resolved: 'https:///Service1.svc'. Could not establish trust relationship for the SSL/TLS secure channel with authority ''. The underlying connection was closed: Could not establish trust relationship for the SSL/TLS secure channel. The remote certificate is invalid according to the validation procedure.HTTP GET Error URI: https:///Service1.svc There was an error downloading 'https:///Service1.svc'. The underlying connection was closed: Could not establish trust relationship for the SSL/TLS secure channel. The remote certificate is invalid according to the validation procedure.

    Read the article

  • Can a WCF Service provide publish/subscribe activity to a Linux-based C++ client application?

    - by Jeremy Roddingham
    I have a WCF service written to provide certain functionality to intranet-based clients. This is easy when a client is running Windows. I want to implement the same functionality for my Windows clients that is available to my linux clients. My questions are? How can I communicate to a linux c++ based client (supporting callback operations for a publish subscribe) type situation? I am aware of using SOAP over the HTTPBinding but is that the only way (does not support callbacks I believe)? Would the same apply if I were using TCPBinding on the service-side? Currently, the service is set up using TCP but what are my options for the linux client communcation? I read somewhere that messages can also be sent (via webservices I believe) in XML rather than SOAP? Which would be a better approach or how to determine which is a better approach? I am trying to understand the options I would have for a WCF data service if I wanted to communicate with it from a linux client. I appreciate all your help. Thank You, Jeremy

    Read the article

  • Selecting which IP address to use for outgoing requests from behind a NAT

    - by iamrohitbanga
    Our organization has several external IP addresses. I am behind 2 layers of NAT and the servers choose which IP address to route my traffic to. Can I specify which IP address to use when finally leaving the organizations network. I know that source routing can be done in IPv4 by adding some options in the header. But can I configure my PC to add these options automatically. I have both a Windows and a Linux Machine.

    Read the article

  • Asp.Net 3.5 Routing to Asmx Webservice?

    - by Maushu
    I was looking for a way to route http://www.example.com/WebService.asmx to http://www.example.com/service/ using only the ASP.NET 3.5 Routing framework without needing to configure the IIS server. Until now I have done what most tutorials told me, added a reference to the routing assembly, configured stuff in the web.config, added this to the Global.asax: protected void Application_Start(object sender, EventArgs e) { RouteCollection routes = RouteTable.Routes; routes.Add( "WebService", new Route("service/{*Action}", new WebServiceRouteHandler()) ); } ...created this class: public class WebServiceRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { // What now? } } ...and the problem is right there, I don't know what to do. The tutorials and guides I've read use routing for pages, not webservices. Is this even possible? Ps: The route handler is working, I can visit /service/ and it throws the NotImplementedException I left in the GetHttpHandler method.

    Read the article

  • ASP.NET 3.5 Routing?

    - by Maushu
    I was looking for a way to route http://www.example.com/WebService.asmx to http://www.example.com/service/ using only the ASP.NET 3.5 Routing framework without needing to configure the IIS server. Until now I have done what most tutorials told me, added a reference to the routing assembly, configured stuff in the web.config, added this to the Global.asax: protected void Application_Start(object sender, EventArgs e) { RouteCollection routes = RouteTable.Routes; routes.Add( "WebService", new Route("service/{*Action}", new WebServiceRouteHandler()) ); } ...created this class: public class WebServiceRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { // What now? } } ...and the problem is right there, I don't know what to do. The tutorials and guides I've read use routing for pages, not webservices. Is this even possible? Ps: The route handler is working, I can visit /service/ and it throws the NotImplementedException I left in the GetHttpHandler method.

    Read the article

  • WCF Service in Windows Services

    - by sivakumar
    I create WCF service library and i test that working fine on WCF Test client(default). when i host the WCF service in winodws service that time i got the error. I am using windows XP sp3, .Net 3.5 and Visual Studio 2008. i got error. Error opening host : HTTP could not register URL "http://+:8731/WCFServerDLL/Service1/." Your process does not have access rights to this namespace (see "http://go.microsoft.com/fwlink/?LinkId=70353" for details). the above link for microsoft i implement the httpcfg. Here i run the "httpcfg.exe set urlacl /u http://localhost:8731/WCFServerDLL/Service1/ /a" i get the result HttpSetServiceConfiguration completed with 0. what is the problem i got same error. can you give me a suggation.

    Read the article

  • Asp.Net 3.5 Routing to Webservice?

    - by Maushu
    I was looking for a way to route http://www.example.com/WebService.asmx to http://www.example.com/service/ using only the ASP.NET 3.5 Routing framework without needing to configure the IIS server. Until now I have done what most tutorials told me, added a reference to the routing assembly, configured stuff in the web.config, added this to the Global.asax: protected void Application_Start(object sender, EventArgs e) { RouteCollection routes = RouteTable.Routes; routes.Add( "WebService", new Route("service/{*Action}", new WebServiceRouteHandler()) ); } ...created this class: public class WebServiceRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { // What now? } } ...and the problem is right there, I don't know what to do. The tutorials and guides I've read use routing for pages, not webservices. Is this even possible? Ps: The route handler is working, I can visit /service/ and it throws the NotImplementedException I left in the GetHttpHandler method.

    Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >