Search Results

Search found 5057 results on 203 pages for 'force'.

Page 153/203 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• Dual Boot Installing Ubuntu 12.04 with Windows 7 (64) on a non UEFI system fails

  - by Randnum

  I cannot seem to install the correct boot loader for a non-UEFI firmware system. I'm trying to install Ubuntu 12.04 and Windows 7 (64) which are technically compatible with GPT but for windows only if the firmware is UEFI enabled. My system uses the old BIOS system and does not support UEFI. Therefore, whenever I finish my Ubuntu install and try to install Windows I get a "cannot install to GPT partition type" error. Even if I use Gparted to format a special NTFS file format for windows it can't handle the GPT partition style because it doesn't have UEFI. But my ubuntu install always forces GPT during installation and never asks if I want to install the old BIOS style MBR instead. How do I resolve this? Both OS's will install fine on their own the problem is when I try to install the second OS it doesn't recognize any of the other's partitions and tries to rewrite it's own on top of the other. I've tried both OS's first and always run into the same problem. Since there is no way to make Windows recognize GPT without upgrading my Motherboard how do I tell Ubuntu to use the old BIOS MBR on install? Do I have to download a special Ubuntu with a specific grub version? or should I manaually configure my partition somehow to force it not to use GPT? Thank you,

  Read the article

• How To Boot with "mem=1024m" Argument using GRUB - Ubuntu 10.04

  - by nicorellius

  I am still working on this question. This new one is a different question so I thought it would be good to post a new question. Is this the proper protocol or should I have just edited the other question? I'm running Ubuntu 10.04 with the kernel 2.6.32-22-generic on a Toshiba Satellite laptop. When I enter the GRUB menu (I have Ubuntu 9.10 installed as well), I can choose which kernel to boot. I use scroll down to the one I want and press "e" and I expect to be able to enter mem=1024m and force the kernel to use this much memory. But when I run cat /proc/meminfo or look in the process manager after booting wth this argument I still see all the RAM: ~2 GB. Am I using this boot argument incorrectly? The boot configuration (before I add anything) looks like this: insmod ext2 set root=(hd0,1) search --no-floppy --fs-uuid --set 10270f21-1c42-494b-bd3f-813c23f6d\ 518 linux /boot/vmlinuz-2.6.32-22-generic root=UUID=10270f21-1c42-494b-b\ d3f-813c23f6d518 ro quiet splash initrd /boot/initrd.img-2.6.32-22-generic The way I did this was that I added the mem=1024m after the last line and pressed Ctrl+x (Emacs save and boot the kernel) and the system booted. I tried adding mem=1024m to the end and the beginning of this list and it appeared to not change the RAM allocation.

  Read the article

• FTP account ownership on vhost directory makes Apache not run website correctly

  - by CodeShining

  I've purchased a virtual server, where I'm given of a non-root sudo-enabled user. Actually I do need to create an FTP account that's not that sudo-able account, so I created a no-login account just for that purpose. I've set up VSFTPd correctly, also enabling the "userlist" feature, to specify which user are permitted to use FTP. Then I created an empty directory under my sudo-able account, and I gave ownership permissions to the second account, so to make it more easy to understand, let's say the main account (the one I do use to manage my VPS) is called ubuntu and the FTP-user is named ftpuser, I created a directory /home/ubuntu/mywebsite giving the ownership to ftpuser:ftpuser. Then I uploaded a worpdress website, whose default permissions are 755 and 644. The issue is that Apache is not given of any privilege to run the website. How can I make the website run properly, and which is the most secure? Should I run that virtualhost with another user (if it's possible)? Should I force the FTP user to use the www-data group (if that's possible) and run with permissions like 775 and 664? How can I solve this issue? Any help is appreciated, I'd like to run it using the default permissions, so any update won't break up anything (because of permissions reset).

  Read the article

• Redirect from folder containing website

  - by Sam

  I have a website reached from this url: http://www.mysite.com/cms/index.php being served from this directory: public_html/cms/index.php In public_html I have this .htaccess RewriteRule (.*) cms/$1 [L] Which lets me get to the site like this: http://www.mysite.com/index.php But now if I reference the 'old' address, I'd like to redirect to the rewritten address with a permanent redirect code. for example: http://www.mysite.com/cms/?q=node/1 is redirected to... http://www.mysite.com/?q=node/1 How can I make this happen? EDIT: Also in the .htaccess file supplied with Drupal(cms), this is written. I've tried enabling it, but it doesn't seem to have any effect. # Modify the RewriteBase if you are using Drupal in a subdirectory or in a # VirtualDocumentRoot and the rewrite rules are not working properly. # For example if your site is at http://example.com/drupal uncomment and # modify the following line: # RewriteBase /drupal EDIT: Including more of my .htaccess file - seems relevant. # Block access to "hidden" directories whose names begin with a period. RewriteRule "(^|/)\." - [F] #Strip cms folder from url RewriteRule (.*) cms/$1 RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !=/favicon.ico RewriteRule ^ index.php [L] # Rules to correctly serve gzip compressed CSS and JS files. # Requires both mod_rewrite and mod_headers to be enabled. <IfModule mod_headers.c> # Serve gzip compressed CSS files if they exist and the client accepts gzip. RewriteCond %{HTTP:Accept-encoding} gzip RewriteCond %{REQUEST_FILENAME}\.gz -s RewriteRule ^(.*)\.css $1\.css\.gz [QSA] # Serve gzip compressed JS files if they exist and the client accepts gzip. RewriteCond %{HTTP:Accept-encoding} gzip RewriteCond %{REQUEST_FILENAME}\.gz -s RewriteRule ^(.*)\.js $1\.js\.gz [QSA] # Serve correct content types, and prevent mod_deflate double gzip. RewriteRule \.css\.gz$ - [T=text/css,E=no-gzip:1] RewriteRule \.js\.gz$ - [T=text/javascript,E=no-gzip:1] <FilesMatch "(\.js\.gz|\.css\.gz)$"> # Serve correct encoding type. Header append Content-Encoding gzip # Force proxies to cache gzipped & non-gzipped css/js files separately. Header append Vary Accept-Encoding </FilesMatch>

  Read the article

• Apache Redirect is redirecting all HTTP instead of just one subdomain

  - by David Kaczynski

  All HTTP requests, such as http://example.com, are getting redirected to https://redmine.example.com, but I only want http://redmine.example.com to be redirected. For example, requests for I have the following in my 000-default configuration: <VirtualHost *:80> ServerName redmine.example.com DocumentRoot /usr/share/redmine/public Redirect permanent / https://redmine.example.com </VirtualHost> <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> . . . </VirtualHost> Here is my default-ssl configuration: <VirtualHost *:443> ServerName redmine.example.com DocumentRoot /usr/share/redmine/public SSLEngine on SSLCertificateFile /etc/ssl/certs/ssl-cert-snakeoil.pem SSLCertificateKeyFile /etc/ssl/private/ssl-cert-snakeoil.key BrowserMatch "MSIE [2-6]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 BrowserMatch "MSIE [17-9]" ssl-unclean-shutdown <Directory /usr/share/redmine/public> Options FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> LogLevel info ErrorLog /var/log/apache2/redmine-error.log CustomLog /var/log/apache2/redmine-access.log combined </VirtualHost> <VirtualHost *:443> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> . . . </VirtualHost> Is there anything here that is cause all HTTP requests to be redirected to https://redmine.example.com?

  Read the article

• Windows 7 explorer crashing trying to read external hard disk

  - by Mario De Schaepmeester

  I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

  Read the article

• Apache: getting proxy, rewrite, and SSL to play nice

  - by Rich M

  Hi, I'm having loads of trouble trying to integrate proxy, rewrite, and SSL altogether in Apache 2. A brief history, my application runs on port 8080 and before adding SSL, I used proxy to strip the 8080 from the url's to and from the server. So instead of www.example.com:8080/myapp, the client app accessed everything via www.example.com/myapp Here was the conf the accomplished this: ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> ProxyPass /myapp http://www.example.com:8080/myapp ProxyPassReverse /myapp http://www.example.com:8080/myapp What I'm trying to do now is force all requests to myapp to be HTTPS, and then have those SSL requests follow the same proxy rules that strip out the port number as my application used to. Simply changing the ports 8080 to 8443 in the ProxyPass lines does not accomplish this. Unfortunately I'm not an expert in Apache, and my skills of trial and error are already reaching the end of the line. RewriteEngine On RewriteCond %{HTTPS} off RewriteRule myapp/* https://%{HTTP_HOST}%{REQUEST_URI} ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> SSLProxyEngine on ProxyPass /myapp https://www.example.com:8443/mloyalty ProxyPassReverse /myapp https://www.example.com:8433/mloyalty As this stands, a request to anything on the server other than /myapp load fine with http. If I make a browser http request to /mypp it then redirects to https:// www.example.com:8443/myapp , which is not the desired behavior. Links within the application then resolve to https:// www.example.com/myapp/linkedPage , which is desirable. Browser requests (http and https) to anything one level beyond just /myapp ie. /myapp/mycontext resolve to https:// www.example.com/myapp/mycontext without the port. I'm not sure what other information there is for me to give, but I think my goals should be clear.

  Read the article

• Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

  - by William

  I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

  Read the article

• Mass-migrating from POP3 to Exchange 2010, how do I copy mailboxes?

  - by Erik P. Skaalerud

  I'm in the process of planning our migration from an internal hosted POP3-server (dovecot) to Exchange 2010. We're using Outlook 2003 for the moment, but will soon upgrade to Outlook 2010. The big problem is that we have about 50 computers here in our HQ, plus ~30 clients in branch offices (wich will get their Exchange migration later sometime). I'm the only IT personel, and having to go around and manually set up Outlook and copy over their PST contents is not a option I'm looking for. Some users have set outlook to keep messages for X number of days on the POP3 server, others have not. Using a POP3 connector to transfer over the mails is not a viable option. Here is what I've done so far: Created a transform for the Office 2003 administrative installation point Created a .PRF file to modify any existing e-mail account to switch over to Exchange (including the RPC-encrypt hotfix described in MSKB 2006508) Tested both transform and PRF, both works Created a test-OU and GPO containing the Office 2003 installation with transform applied, also works My big question is: How can I force Outlook to import any existing .PST into the new Exchange mailbox when the user starts up Outlook for the first time after the MST/PRF have been applied? Is this possible?

  Read the article

• Strategy for Incremental Datasource fetchings in Excel

  - by user1352530

  I am in an scenario with a table that is refresh by a third app every week. I need to keep accumulating all data in Excel, using an ODBC connection to the database. I am wondering Approach 1: Is there a way to force Excel to append results for every update (this update would be triggered according to a parameter that indicates week)? I tried to define the table for which the connection loads using a dynamic reference but once is anchored first time, table position is never redefined Approach 2: Use an ETL to accumulate all weekly results into a staging table and then connect Excel to it in real time. But, I would need a mechanism for caching old data, as I cannot grow exponentially the time Excel opens. Imagine after 10 years, Excel would need to update at opening 10 years fo data before showing it. Is there a way to store already fetched data and increment it at real time (when book is opened) by selecting new data (with a query/filter of something) Thanks EDIT: Maybe it's better to ask it that way: What is the optimal strategy for a table that keeps growing and needs to be read in real time by Excel? I just don't want to fetch absolutely all data after some months...

  Read the article

• USB drive was bootable, but no longer boots

  - by i-g

  I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? I think it lost some pixie dust when I formatted it with the standard Windows formatting tool (it was quicker than deleting files), but I have no idea what it was or how to get it back. The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

  Read the article

• Blue screen of Death on Install

  - by Toby Allen

  I have a machine with Windows Vista Installed. It has an Intel X25 SSD as the System Drive I want to reinstall (I plan to format and overwrite Vista) with XP. When I boot up using the Dell XP CD it loads the initial drivers then i get a Blue Screen. This is quite concerning. The installed OS works ok, but its giving problems so I want to remove it. Should I just format the SSD and try again? Will this make any difference? Can I do something to avoid hitting the Blue Screen? Its possible I had corrupt sectors on one of the other disks, will a new XP install use the System drive or drive 0? Can I force the install to use a specific drive when installing? Error: *** STOP: 0x0000007B (0xF78D2524,0x0000034,0x00000000,0x00000000) I never did find the answer, however I removed the SSD and tried to install on other disk - CRASH I disconnected the other disk and tried to install with only SSD plugged in - CRASH I removed 1 block of RAM - CRASH I used a windows 7 CD - NO CRASH

  Read the article

• How does one debug Windows network share authentication?

  - by ajs410

  I have machine0 with 32-bit Vista, logged in as a domain user, running a VMWare image of 32-bit Vista, logged in as a local user, with the VM set to bridge the network. From an administrator account (called admin) within the VM, I try to access the hidden C$ share on machine0 (i.e. start - run - "\\machine0\C$\"). I get no prompts for credentials. Worse, machine0 has an admin account (different password), and machine0\admin gets locked out when VM\admin tries to access the network share. I get a message several seconds later, which feels like a cached credential failure leading to the lockout. I have checked several places for cached credentials; net use, Stored Usernames and Passwords, mapped shares. I rebooted (both machine0 and VM) to make sure the session was clear of any cached credentials. I can force net use to use my domain credentials when accessing machine0, and then I can see the share. I can also see shares that do not require credentials. I decided to try another machine on the network (machine1), 64-bit Vista, local user. This machine has no lockout policy, and after several seconds (feels like failed cached credentials again) it prompts me for credentials. After I enter them, it re-prompts me, saying "logon unsuccessful" (tried my domain credentials, and also machine1\admin's). Which is bogus, because I proceed to log on with remote desktop using the machine1\admin credentials. I have tried this on another machine (machine2, 64-bit Vista), running a copy of the same 32-bit VM, and I don't remember having this problem. machine0 has a fingerprint reader...could that try storing passwords and interfere? Are there any places I'm missing where there could be cached credentials? Is there a way to see what credentials are flying around when I try to connect?

  Read the article

• USB drive was bootable, but no longer isn't

  - by i-g

  I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

  Read the article

• RAID5 issue after replacing motherboard and upgrading firmware

  - by 8steve8

  ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with Windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. This screenshot should show that the SNs match, which raises the question why the software doesn't realize the drive is a member of the array. I'd like to know if anyone has experienced anything similar, and what should I do, can I force the drive to be recognized as a member (without wiping data)?

  Read the article

• troubleshooting postifx -> exchange connection issues

  - by Systemspoet

  I have three linux-based mail routers that run postfix and relay mail to our on-premise exchange server as well as to outlook.com, splitting the mail based on ldap atttributes. What I've observed sporadically since upgrading this spring from Exchange 2007 to 2010 is that all three of the mail relays will, for about 20 minutes, fail to connect to exchange. Postfix logs it as "lost connection with exchange.contosso.edu" ; this problem almost always occurs to all three mail relays at the same time, and lasts for slightly under 20 minutes. If I can catch it while it's occuring, and I manually do "telnet exchange.contosso.edu 25" from one mail relay and force a message through (helo, mail from, rcpt to, data, etc), then it clears that relay up. The exchange "server" is actually two machines with the HT role on them, load balanced via windows NLB. I've worked pretty hard to figure out what's happening from the postfix side and I can't see any evidence of any misbehavior. My question is, how do I attack the problem from the exchange side? Is there a connection log, or a debug setting, or something I can do to log all of the inbound connections and tell me what's causing exchange to drop them?

  Read the article

• Separated virtual networks with same subnet range with 2 interface

  - by Coolpet

  I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

  Read the article

• Allow outgoing connections for DNS

  - by Jimmy

  I'm new to IPtables, but I am trying to setup a secure server to host a website and allow SSH. This is what I have so far: #!/bin/sh i=/sbin/iptables # Flush all rules $i -F $i -X # Setup default filter policy $i -P INPUT DROP $i -P OUTPUT DROP $i -P FORWARD DROP # Respond to ping requests $i -A INPUT -p icmp --icmp-type any -j ACCEPT # Force SYN checks $i -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # Drop all fragments $i -A INPUT -f -j DROP # Drop XMAS packets $i -A INPUT -p tcp --tcp-flags ALL ALL -j DROP # Drop NULL packets $i -A INPUT -p tcp --tcp-flags ALL NONE -j DROP # Stateful inspection $i -A INPUT -m state --state NEW -p tcp --dport 22 -j ACCEPT # Allow established connections $i -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow unlimited traffic on loopback $i -A INPUT -i lo -j ACCEPT $i -A OUTPUT -o lo -j ACCEPT # Open nginx $i -A INPUT -p tcp --dport 443 -j ACCEPT $i -A INPUT -p tcp --dport 80 -j ACCEPT # Open SSH $i -A INPUT -p tcp --dport 22 -j ACCEPT However I've locked down my outgoing connections and it means I can't resolve any DNS. How do I allow that? Also, any other feedback is appreciated. James

  Read the article

• VPN: Disable class based route addition for Windows XP/Vista

  - by brgsousa

  Paraphrasing this SuperUser link: When you set up a VPN, the Windows default is to enable "Use default gateway on remote network." A new default route is added to the routing table pointing to the remote network's gateway, and the existing default route has its metric increased to force all Internet traffic to traverse the tunnel and use the remote network's gateway. All traffic uses the VPN, and traffic destined for the outside world is directed to the remote gateway. When the VPN drops, the route to the remote gateway is removed and the original default route is set back to the original metric. Unchecking "use default gateway on remote network" means that new default route isn't added, so Internet traffic goes out the local gateway, but a new classful route is added to the routing table, using the local adapter's IP, pointing down the VPN. Only traffic destined for the classful network of the local adapter goes down the VPN. This may not be what you want. Checking "Disable class based route addition" means that classful route isn't added to your machine when the VPN starts up, and you'll need to add the appropriate routes for networks that should be routed through the tunnel. But, the option "Disable class based route addition" is available ONLY for Windows 7. How can I do something like that for Windows XP or Vista since they don't have that option? I have searched about for that but, no solution yet.

  Read the article

• How can I rapidly switch hosts?

  - by EAMann

  I'm in the process of migrating a forum setup from one version of the software on one machine (older shared Windows host) to a new VPS (Windows Server 2008). To install the software, I used my hosts file to temporarily point the domain at the new IP address. To see the old site, I obviously re-edit the hosts file to remove the reference. But this leaves me constantly adding/removing a # from my hosts file just so I can switch back and forth between the two servers. Is there a way to do this more rapidly? I've found a handful of toggling batch scripts, but all they do is automate the addition/removal of the # character ... so there's still a noticeable lag where I have to repeatedly hit F5 to force my system to detect the new settings. Ideally, I could view both servers at the same time on the same machine. Maybe one through a regular browser session and one through some kind of a proxy. Unfortunately, I don't have the first idea how to set that up. Ideas?

  Read the article

• Expand a volume residing on one X-RAID disk installed on a Netgear ReadyNas Duo v2

  - by Sid

  I've got a Netgear ReadyNas Duo v2 (2 disk slots). System is configured with X-RAID which does not provide flexibility but automatically expands based on a sort of RAID-5 logic. I had 2 500 GB hard disk installed, redundant, so I had 500 GB of volume size. I wanted to upgrade the whole system to 3 GB * 2 hard disk maintaining both the data already on the NAS and the data on one of the two 3 TB hard disks. So I did this: Unplugged one disk from the ReadyNas. Now the readynas has 1*500 GB non redundant. Plugged one empty 3 TB hard disk. Now the readynas has 1*500 GB + 1*3 TB, redundant. I waited for the resync. I then unplugged the 500 GB hard disk, so that I have only the 3 TB hard disk with the previous data. Now what I want is to copy the data on my other 3 TB hard disk in the NAS, so that I can plug this other disk in the NAS and use it for redundancy. The problem is that: the NAS has the (single) 3 TB hard disk in X-RAID, but the volume does not expand to 3 TB, it remains fixed to 500 GB. Is there a way to tell the ReadyNas to force expanding the volume to the whole disk without plugging in another hard disk of the same size?

  Read the article

• Scripted redirection for Outlook 2003

  - by John Gardeniers

  We have a staff member in sales who has gone onto a 4 day week (getting ready for retirement), so each Thursday afternoon her email needs to be forwarded to another user and each Friday afternoon it needs to be set back. I'm using the VBS script below to do this, run via the Task Scheduler. Although the script appears to do it's job, based on what I see when I view the user's Exchange settings, Exchange doesn't always recognise that the setting has changed. e.g. Last Thursday the forwarding was a enabled and worked correctly. On Friday the script did it's thing to clear the forwarding but Exchange continued to forward messages all weekend. I found that I can force Exchange to honour the changed setting be merely opening and closing the user's properties in ADUC. Of course I don't want to have to do that. Is there a non-manual way I can have Exchange read and honour the setting? The script (VBS): ' Call this script with the following parameters: ' ' SrcUser - The logon ID of the suer who's account is to be modified ' DstUser - The logon account of the person to who mail is to be forwarded ' Use "reset" to clear the email forwarding SrcUser = WScript.Arguments.Item(0) DstUser = WScript.Arguments.Item(1) SourceUser = SearchDistinguishedName(SrcUser) 'The user login name Set objUser = GetObject("LDAP://" & SourceUser) If DstUser = "reset" then objUser.PutEx 1, "altRecipient", "" Else ForwardTo = SearchDistinguishedName(DstUser)' The contact common name objUser.Put "AltRecipient", ForwardTo End If objUser.SetInfo Public Function SearchDistinguishedName(ByVal vSAN) Dim oRootDSE, oConnection, oCommand, oRecordSet Set oRootDSE = GetObject("LDAP://rootDSE") Set oConnection = CreateObject("ADODB.Connection") oConnection.Open "Provider=ADsDSOObject;" Set oCommand = CreateObject("ADODB.Command") oCommand.ActiveConnection = oConnection oCommand.CommandText = "<LDAP://" & oRootDSE.get("defaultNamingContext") & ">;(&(objectCategory=User)(samAccountName=" & vSAN & "));distinguishedName;subtree" Set oRecordSet = oCommand.Execute On Error Resume Next SearchDistinguishedName = oRecordSet.Fields("DistinguishedName") On Error GoTo 0 oConnection.Close Set oRecordSet = Nothing Set oCommand = Nothing Set oConnection = Nothing Set oRootDSE = Nothing End Function

  Read the article

• What are possible results/side effects if replication between DC's in a Windows domain is unable to occur?

  - by hydroparadise

  There's plenty of administration literature out there how to properly manage Windows servers. But in dealing with real life, things don't always occur like you want them to. In Microsoft's Windows Server 2003 Administrator's Companion, out of 1400+ pages, theres only one page that I could find when it comes up setting up additional domain controlers. They make it sound seemless and don't reveal a whole lot on what happens if "peer" DC's are unable to replicate. Down to the specific issue at hand, we had a DC go down about a month ago due to a bad RAID controller. There was nothing critical that waranted imediate attention, so bringing it back up got put on the back burner. A month later, we get the DC back up and running and everyting seemed ok. The next day, nobody is able to logon complaining that the "user does not exist" or "unable to establish a trust relationship". Knowing that I had just put the downed DC back on the network, I immediately took it back off the network and had everybody restart the workstations. After that, exchange was fine, shares became available, and everybody was able to log in. After doing some event log swimming, it would appear that everything started due to replication issues on the SYSVOL. I've read where you can force replication, but that would mean putting it back on the network. I am afraid to put the DC back on the network in fear that something else could go wrong. So, what other issues could one expect to run into where two DC's are unreplicated for over a month?

  Read the article

• How to stop my wireless adapter from received dhcp from router (windows)

  - by baobeiii

  Hi, I have a windows 7 computer which is connected via vpn to an OpenVpn server which happens to be in another country. I have all internet traffic being routed from my computer through the vpn to the server. However dns queries are not going through the vpn, but are instead going directly to my isp's dns via a route outside of the vpn tunnel. This is happening because my wireless adapter is configured to obtain DNS server address automatically. The router that stands between my computer and the internet happens to have a DCHP server running on it that is assinging my computer with the DNS addresses of the isp. The issue is, i haven't been able to stop my wireless adapter on my computer from receiving the dns settings from the router. I've tried selecting 'use the following dns server addresses' and then just leaving them blank, but ipconfig /all shows me that this hasn't worked and i'm still getting dns form the router. So is there any way to completely stop my windows wireless adapter from receiving these settings from the router? I have the OpenVpn server pushing to my computer's tun adapter the dns that it should be using. I'd rather solve this in a way that doesn't involve disabling the dhcp server on the router or fiddling with the router. The reason is i'm on a laptop and i want my vpn to not leak dns even when i'm out, for example in wireless hotspots. I know if i could just force the wireless adapter to ignore the router's dhcp server then my dns queries would go through the tunnel to the dns address pushed by the OpenVpn server. Sorry, i know thats long winded, if you have any idea's please do tell me. Thanks and merry xmas.

  Read the article

• How to make my Ubuntu an internet gateway for my Android phone

  - by yacine

  I want to use the internet of my school on my Android, the problem is they have a Squid proxy, and many applications on my phone don't use the proxy at all. The obvious solution is to install a transparent proxy on my Android to force all applications to connect through it. The problem is that I need to root the phone to make it work, and I don't want to do it because it's not really my phone and rooting is a little risky- Another solution, which is safer, is to make my computer run as a gateway, so I put my Ubuntu IP in the gateway parameter of the phone. I'm running a small proxy on my ubuntu (cntlm), so I redirect the Android traffic to it. I did it with "iptables" as follows: iptables -t nat -A PREROUTING -s 10.0.1.118 -p tcp -j REDIRECT --to-ports 8888 iptables -t nat -A PREROUTING -s 10.0.1.118 -p udp -j REDIRECT --to-ports 8888 10.0.1.118 is the IP of the phone, 8888 is the port of cntlm (proxy on my PC). Now, on the phone: When I enter www.google.com on the navigator I get nothing (web site not found, error message of Firefox). But, when I enter http://74.125.143.101 (IP of Google) I get an error message from the school proxy (so it worked in some way – my PC redirected the traffic of the phone to the Squid proxy). The error message is : The requested URL could not be retrieved while trying to process the request get / http/1.1 host 74.125.143.101 user-Agent ... ... I think the problem is in the "GET" header,it should be GET 74.125.143.101 HTTP/1.1. But I don't understand what's happening, and I'm a certified CCNA.

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >