Search Results

Search found 18677 results on 748 pages for 'current'.

Page 154/748 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

• Hard Disk Not Counting Reallocated Sectors

  - by MetaNova

  I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• SELinux - Allow multiple services access to same /home/dir

  - by Mike Purcell

  I currently have SELinux enabled and have been able to configure apache to allow access to /home/src/web with a chcon command granting the 'httpd_sys_content_t' type. But now I am trying to serve the rsyslogd.conf file from the same directory, but every time I start rsyslogd I see an entry in my audit log saying that rsyslogd was denied access. My question is, is it possible to grant two applications the ability to access the same directory, while still keeping SELinux enabled? Current perms on /home/src: drwxr-xr-x. src src unconfined_u:object_r:httpd_sys_content_t:s0 src Audit log message: type=AVC msg=audit(1349113476.272:1154): avc: denied { search } for pid=9975 comm="rsyslogd" name="/" dev=dm-2 ino=2 scontext=unconfined_u:system_r:syslogd_t:s0 tcontext=system_u:object_r:home_root_t:s0 tclass=dir type=SYSCALL msg=audit(1349113476.272:1154): arch=c000003e syscall=2 success=no exit=-13 a0=7f9ef0c027f5 a1=0 a2=1b6 a3=0 items=0 ppid=9974 pid=9975 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=30 comm="rsyslogd" exe="/sbin/rsyslogd" subj=unconfined_u:system_r:syslogd_t:s0 key=(null) -- Edit -- Came across this post, which is sort of what I am trying to accomplish. However when I viewed the list of allowed sebool params, the only relating to syslog was: syslogd_disable_trans (SELinux Service Protection), seems like I can maintain the current SELinux 'type' on the /home/src/ dir, but set the bool on syslogd_disable_trans to false. I wonder if there is a better approach?

  Read the article

• Is a Hyperthreaded CPU more powerful and more efficient than a Dual-core CPU? [closed]

  - by user1811864

  which computer to choose with Pentium processor hello they are getting rid of the old computer equipment in the office and i have to choose the computer to take home i get first choice to pick. -15 inch lcd screen 4 gb of ram core 2 duo dual Core E8400 3.00 GHz dvd writer windows vista/ linux -15 inch crt monitor with 2 gb ram and pentium 4 2 ghz single core HT technology windows xp hardisks both 250 GB my friend is telling me to choose the second one Pentium single core HT because he told me it runs faster becuase of HT technology and cooler and consumes less current electricity so it wont get overheated because it has HT technology so it's high definition for encoding and watching HD movies and HD sound and is like a gaming pc to play internet games. And also he said the dual core 8400 runs at 3 ghz compared to the 2 ghz so it heats very much because of the two extra cores so it takes more current raising electricty bills and is not good for gaming and watching HD movies and internet flash animations and games because of getting heated everytime. And he wants to choose and take the E8400 because he has air conditioning at home so it will be safe from heating. So which one computer should i take is it really faster because of the HT High definition technology and will i be able to play internet flash card games better and watch good HD movies Youtube etc and play all the music and songs.

  Read the article

• Copy all installed programs & files in a hard disk (which has 32 bit Windows 7) and clone/transfer it to another computer which has 64 bit Windows 7

  - by galacticninja

  I recently got a new PC which has a 64-bit Windows 7 installed. The current PC that I am using has a 32-bit Windows 7 installed. I would like to know if there is a software that can copy all my installed programs and files in the hard disk with the 32-bit Windows 7 PC and transfer it to the newer PC's hard disk which has a 64 bit version of Windows 7. This is essentially like "cloning" a hard disk but I would like to use a 64-bit OS in the target drive, instead of also using the 32-bit OS of the source drive. I would like to do this I can avoid reinstalling and reconfiguring my installed programs and files again on the new PC. If possible, I would like the new PC to work as it was in my previous PC, with the installed programs, configuration and files intact except that the OS is now 64-bit and the hard disk has a larger capacity. I have heard of programs that can clone a hard disk, but my concern is that the 32-bit Windows 7 OS will also be cloned to the new 64-bit PC. If it is not possible to transfer my installed programs and settings like the way I described, are there software that can make it easier to migrate my installed programs, their configurations and my files from a 32-bit Windows 7 PC to a 64-bit Windows 7 PC? Details: I have a SATA to USB connector/adapter to copy files in the current hard disk to the newer one. The two PCs are connected through LAN, so I can also transfer files through LAN. Both PCs only have one hard disk.

  Read the article

• Why can't I see all of the client certificates available when I visit my web site locally on Windows 7 IIS 7?

  - by Jay

  My team has recently moved to Windows 7 for our developer machines. We are attempting to configure IIS for application testing. Our application requires SSL and client certificates in order to authenticate. What I've done: I have configured IIS to require SSL and require (and tried accept) certificates under SSL Settings. I have created the https binding and set it to the proper server certificate. I've installed all the root and intermediate chain certificates for the soft certificates properly in current user and local machine stores. The problem When I browse to the web site, the SSL connection is established and I am prompted to choose a certificate. The issue is that the certificate is one that is created by my company that would be invalid for use in the application. I am not given the soft certificates that I have installed using MMC and IE. We are able to utilize the soft certs from our development machines to our Windows 2008 servers that host the application. What I did: I have attempted to copy the Root CA to every folder location for the Current User and Location Machine account stores that the company certificate's root is in. My questions: Could I be mishandling the certs anywhere else? Could there be a local/group policy that could be blocking the other certs from use? What (if anything) should have to be done differently on Windows 7 from 2008 in regards to IIS? Thanks for your help.

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

• How can I "filter" postfix-generated bounce messages?

  - by Flimzy

  We are using postfix 2.7 and custom SMTPD (based on qpsmtpd) in highly customized configuration for spam filtering. We have a new requirement to filter postfix-generated bounces through our custom qpsmtpd process (not so much for content filtering, but to process these bounces accordingly). Our current configuration looks (in part) like this: main.cf (only customizations shown): 2526 inet n - - - 0 cleanup pickup fifo n - - 60 1 pickup -o content_filter=smtp:127.0.0.2 Our smtpd injects messages to postfix on port 2526, by speaking directly to the cleanup daemon. And the custom pickup command instructs postfix to hand off all locally-generated mail (from cron, nagios, or other custom scripts) to our custom smtpd. The problem is that this configuration does not affect postfix generated bounce messages, since they do not go through the pickup daemon. I have tried adding the same content_filter option to the bounce daemon commands, but it does not seem to have any effect: bounce unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 defer unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 trace unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 For reference, here is my main.cf file, as well: biff = no # TLS parameters smtpd_tls_loglevel = 0 smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${queue_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${queue_directory}/smtp_scache smtp_tls_security_level = may mydestination = $myhostname alias_maps = proxy:pgsql:/etc/postfix/dc-aliases.cf transport_maps = proxy:pgsql:/etc/postfix/dc-transport.cf # This is enforced on incoming mail by QPSMTPD, so this is simply # the upper possible bound (also enforced in defaults.pl) message_size_limit = 262144000 mailbox_size_limit = 0 # We do our own message expiration, but if we set this to 0, then postfix # will try each mail delivery only once, so instead we set it to 100 days # (which is the max postfix seems to support) maximal_queue_lifetime = 100d hash_queue_depth = 1 hash_queue_names = deferred, defer, hold I also tried adding the internal_mail_filter_classes option to main.cf, but also tono affect: internal_mail_filter_classes = bounce,notify I am open to any suggestions, including handling our current content-filtering-loop in a different way. If it's not clear what I'm asking, please let me know, and I can try to clarify.

  Read the article

• How do I uninstall a ruby version installed via source?

  - by Aaron McIver

  I installed a version (1.9.3-p194) of ruby via source using make install and realized this may have been the wrong route to take. Upon doing this, I realized this was a mistake and I should be using a solution such as rvm to address my ruby versions within the OS. I looked to see if an uninstall existed to be ran in conjunction with make and it didn't. I then proceeded to install rvm and add the aforementioned version in to my list of managed rubies within rvm which is not listed as ext-ruby-1.9.3-p194. rvm rubies ext-ruby-1.9.3-p194 [ x86_64 ] =* ruby-1.9.3-p194 [ x86_64 ] # => - current # =* - current && default # * - default** When I perform an rvm remove, it simply removes it from the rubies list however it still exists within /usr/local/bin. I am not concerned with the system install ruby version residing in /usr/bin as I understand that is tied to the OS and should simply be ignored. How can I safely uninstall/remove the aforementioned version and all the places in which it was installed, short of looking at the install script?

  Read the article

• How to allow users to transfer files to other users on linux

  - by Jon Bringhurst

  We have an environment of a few thousand users running applications on about 40 clusters ranging in size from 20 compute nodes to 98,000 compute nodes. Users on these systems generate massive files (sometimes 1PB) controlled by traditional unix permissions (ACLs usually aren't available or practical due to the specialized nature of the filesystem). We currently have a program called "give", which is a suid-root program that allows a user to "give" a file to another user when group permissions are insufficient. So, a user would type something like the following to give a file to another user: > give username-to-give-to filename-to-give ... The receiving user can then use a command called "take" (part of the give program) to receive the file: > take filename-to-receive The permissions of the file are then effectively transferred over to the receiving user. This program has been around for years and we'd like to revisit things from a security and functional point of view. Our current plan of action is to remove the bit rot in our current implementation of "give" and package it up as an open source app before we redeploy it into production. Does anyone have another method they use to transfer extremely large files between users when only traditional unix permissions are available?

  Read the article

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• Salary Survey Entry Level network position [closed]

  - by will

  Hello, I started interning with a company about 5 months ago and for the past 7 months I have been a normal part time employee. This week I have a review, where I am hoping to get a raise. I started at $8 interning, and now I'm up to $13. What I am trying to figure out is how to survey what others are making in similar positions so I can take it to the review as a base number. here are my thoughts on my position right now. Review Thoughts My Qualifications: • Associates of applied Science - IT network Specialist • CompTIA A+ certification • CompTIA Server+ certification • CompTIA Network+ certification • Currently pursuing Cisco certifications • Junior status at Insert college Pursuing Bachelors in Information Technology with an emphasis in Networking. 3.4 GPA • 1 year of working at Insert Company. My contributions to Insert Company • Offering near fulltime through semester and fulltime through summer. • Ability to work after hours and on weekends • Developed and support helpdesk system • Set up and maintain Update server to keep desktop clients up to date • Deployed and maintain antivirus solution for end users • Assist with main projects such as SAN, Virtualization, and network survey. Any tips on determining an asking number would help. I was thinking $17-$18, am I way off here? • Migrating end user stations to Windows 7 (current project) • Developing imaging solution for Desktop PCs (current project)

  Read the article

• Snapshotting single disk of running Hyper-V VM

  - by modelnine

  I'm currently somewhat at a loss of how to create a snapshot of a single virtual hard-disk of a running Hyper-V VM. Generally, creating a differential disk while a server is shut down is no problem (i.e., call the new-vhd cmdlet and pass a ParentPath, then update the VHD-binding of the respective VM-device), but while the host is running, all I can find is checkpointing the VM as a whole (which creates snapshots of all attached disks), and leaves the VM-state in a form which isn't easily processable by external tools (i.e., it requires reading additional meta-data from the VM). Generally, what'd I'd like to happen for a single-disk snapshot (in my understanding) is: Pause the VM Rename current disk to some other name which specifies it as a base-snapshot Create a new VHD which has the renamed VHD as parent path and is marked as "current" Swap the VHD for the VM for the snapshotted hard-disk to the newly created differential VHD Resume the VM Is there any means to do this programatically? Update: I've seen that this is actually possible with SCSI-disks, i.e. pause the VM, remove the SCSI disk, make the snapshot, reattach the SCSI disk at the same position, resume the VM. And, the VM resumes properly. But: is something similar also possible with G1 machines for the boot disk which is always IDE?

  Read the article

• Extending ext4 partition on debian7.0 on vsphere

  - by VoidPointer

  I have allocated thin provisioning of 15GB when i found 8GB as insufficient. Now debian guest is not able to recognize the change of size. root@debian7-x64:~# lvdisplay --- Logical volume --- LV Path /dev/debian7-x64/root LV Name root VG Name debian7-x64 LV UUID EU6mg0-XTXC-ci3D-bQJi-7XN6-r8Hp-SYxcj0 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 1 LV Size 7.39 GiB Current LE 1892 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:0 --- Logical volume --- LV Path /dev/debian7-x64/swap_1 LV Name swap_1 VG Name debian7-x64 LV UUID xDNtoz-tJUq-M5D6-GGCN-gzcD-fwUv-fYYDR1 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 2 LV Size 376.00 MiB Current LE 94 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:1 root@debian7-x64:~# pvdisplay --- Physical volume --- PV Name /dev/sda5 VG Name debian7-x64 PV Size 7.76 GiB / not usable 2.00 MiB Allocatable yes (but full) PE Size 4.00 MiB Total PE 1986 Free PE 0 Allocated PE 1986 PV UUID SehkzH-Gq8Y-jI2f-27Tb-uv1Z-tR1R-5OnTxR root@debian7-x64:~# sfdisk -s /dev/sda: 15728640 /dev/mapper/debian7--x64-root: 7749632 /dev/mapper/debian7--x64-swap_1: 385024 total: 23863296 blocks Help me to extend this partition. No problem in rebooting. I dont have any live CD. Environment : debian 7, with lvm, on vsphere, ext4 partition. Can provide more details when needed.

  Read the article

• TFS 2010 Subfolder Permissions

  - by gmcalab

  I am a TFSAdmin and when I have a TFS project in which a subfolder needs specific permissions to deny some users. So, I right click on the folder in question hit Properties, and click the Security tab. There I select the Windows User or Group radio, then click Add. I put in the AD User that I want specific permissions for and hit Check Names. That resolves, so I click OK. Next, I select the permissions to Allow or Deny below in the Permissions for list. I hit OK. The permission are honored by TFS, this user no longer has PendChange permissions and I was expecting. The odd thing is, I was expecting to be able to go back into the Security tab and see that User in the list of Users and Groups and see the current state. But the list is always empty. Not sure why, but the permissions are definitely being honored, I can re-add the user with different permissions and those are also honored. Any ideas why the current users are not showing up in the Users and Groups list under the Security tab for a folder's properties? I also used the tf permission $\... to see if there were any permissions but it always returns There are no permissions set for this item (Inherit: Yes)

  Read the article

• Extending partition on linux gparted but not more space in the vm

  - by Asken

  I have a vm test installation of a linux running a build server. Unfortunately I just pressed ok when adding the disk and ended up with an 8gb drive to play with. Well into the test the builds are consuming more and more space, of course. The vm drive was resized to 21gb and using gparted I expanded the drive partitions and that all worked fine but when I go back into the console and do df there's still only 8gb available. How can I claim the other 13gb I added? fdisk -l Disk /dev/sda: 21.0 GB, 20971520000 bytes 255 heads, 63 sectors/track, 2549 cylinders, total 40960000 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0006d284 Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 40959999 20229121 5 Extended /dev/sda5 501760 40959999 20229120 8e Linux LVM vgdisplay --- Volume group --- VG Name ct System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 2 Max PV 0 Cur PV 1 Act PV 1 VG Size 19.29 GiB PE Size 4.00 MiB Total PE 4938 Alloc PE / Size 1977 / 7.72 GiB Free PE / Size 2961 / 11.57 GiB VG UUID MwiMAz-52e1-iGVf-eL4f-P5lq-FvRA-L73Sl3 lvdisplay --- Logical volume --- LV Name /dev/ct/root VG Name ct LV UUID Rfk9fh-kqdM-q7t5-ml6i-EjE8-nMtU-usBF0m LV Write Access read/write LV Status available # open 1 LV Size 5.73 GiB Current LE 1466 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:0 --- Logical volume --- LV Name /dev/ct/swap_1 VG Name ct LV UUID BLFaa6-1f5T-4MM0-5goV-1aur-nzl9-sNLXIs LV Write Access read/write LV Status available # open 2 LV Size 2.00 GiB Current LE 511 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:1

  Read the article

• Specify default group and permissions for new files in a certain directory

  - by mislav

  I have a certain directory in which there is a project shared by multiple users. These users use SSH to gain access to this directory and modify/create files. This project should only be writeable to a certain group of users: lets call it "mygroup". During an SSH session, all files/directories created by the current user should by default be owned by group "mygroup" and have group-writeable permissions. I can solve the permissions problem with umask: $ cd project $ umask 002 $ touch test.txt File "test.txt" is now group-writeable, but still belongs to my default group ("mislav", same as my username) and not to "mygroup". I can chgrp recursively to set the desired group, but I wanted to know is there a way to set some group implicitly like umask changes default permissions during a session. This specific directory is a shared git repo with a working copy and I want git checkout and git reset operations to set the correct mask and group for new files created in the working copy. The OS is Ubuntu Linux. Update: a colleague suggests I should look into getfacl/setfacl of POSIX ACL but the solution below combined with umask 002 in the current session is good enough for me and is much more simple.

  Read the article

• Serious 64-bit laptop

  - by Daniel Gehriger

  For the past couple of years, I have been using an IBM Thinkpad T60p for daily work (software development, desktop & embedded). I am extremely satisfied with this machine, due to its robustness. It also has a few features I depend on: a high resolution display: 15.0" TFT FlexView display with 1600x1200 (UXGA); excellent keyboard; decent graphics and CPU performance. Some of the software I develop benefits from larger amounts of RAM, and 3GB (Windows 7 32-bit) or 4GB (Windows 7 64-bit on T60p) are no longer sufficient. My customers run desktop computers with 20GB and more, and I need to have at least 8GB to at least be able to run reasonable test cases. So I'm shopping around for a new laptop, but I'm struggling to find anything that matches my requirements: must run Windows 7 64-bit Pro or higher; must support at least 8GB of RAM (more is better) high screen resolution! While I prefer 4:3 I can live with wide screen. But I really hope to find something with a vertical screen resolution similar to what I have now... portable, so < 16" but = 14" I realize that FlexView isn't available anymore, but I'd like to avoid a glossy screen if possible. decent (not more) graphics performance, ideally hybrid (I'm doing a lot of CAD, never games). good keyboard reasonable CPU -- but I'm still fine with my current Core 2 Duo, so that shouldn't be too complicated. The T60p fits all those requirements, except the 8GB of RAM. Can you help me find a current notebook that would match most of them? I don't mind changing brand. Thanks!

  Read the article

• Thunderbird: export email account settings

  - by zpea

  I'd like to create a new profile for Thunderbird using the same mail accounts I already configured in my old profile. As it is quite a number of accounts, it would be great to have a way to export/import them instead of writing down the settings just to fill in again in the new profile. Using web search and search here I mainly found following suggestions that do not match what I need: Copy the whole profile: Not possible for me as I don't want to copy other settings, the downloaded mail data etc. and the old profile broke when running out of space in the home folder anyway. Use mozBackup: There seem to be several programs by that name (forks?). In any case, it's Windows-only and hence no option (I am mostly on Linux and prefer platform-independent solutions anyway) Use accountex: Seems to do what I want, but it is not compatible with current Thunderbird version (supports only up to version 3.1) Posts with various tips from 4 years ago: Top results in the web search with the G. But they do not work in current versions of Thunderbird either. Did I overlook anything? After all, it doesn't sound like I was looking for something nobody ever looked for.

  Read the article

• Pulling application updates from closest server?

  - by Mike Morris

  Setup: 6 Major Sites with Server 2003/2008 DCs doing DHCP/AD Integrated DNS, each on their own subnet. All connect back to datacenter through a 3 mbps WAN ERP server running in the datacenter, accessed by clients at all sites Currently, when we update the software, I manually push a copy of the updated client/config files down to each DC. I have a script that we run on each PC to update the clients. It determines what subnet the PC is on, and pulls the software from that DC. It's messy, but it works. The client has an autoupdate feature, but it'll only pull from the application server (which is housed in the datacenter, over the 3 meg link). It takes forever, since the updates are not "patches" but a full version of the client, even for minor upgrades (bad design). After the most recent patch, you can configure the clients to pull from a different server. Unfortunately, it is the same for all clients. Is there some kind of DNS magic I can use to pull from the local server? For instance, if I tell the clients their update server is ERPUPDATE, can I have their local DNS server return a different IP for ERPUPDATE than the other sites? Example: Client 1 is at site A, client 2 is at site b. They each run the software and a version change is detected. As per the config files, the clients look to ERPUPDATE for their updated client. Client 1 queries DNS for the IP of ERPUPDATE at its current location (site A) DNS at site A returns 192.1.1.5 Client 1 pulls update from 192.1.1.5 Client 2 queries DNS for the IP of ERPUPDATE at its current location (site B) DNS at site B returns 192.1.2.5 Client 2 pulls update from 192.1.2.5 Excuse the poor explanation, I worked 61 hours over the weekend and haven't completely rebounded. I'll be happy to clarify if needed!

  Read the article

• How to safely send newsletters on VPS (SMTP) w/ non-hosted domain as "From" email?

  - by Andy M

  Greetings, I'm trying to understand the safest way to use SMTP. I'm considering purchasing a second virtual server mainly for email sending, on which I will set up PHPlist (a free open-source mailing program), so we have the freedom to send unlimited newsletters (...well, 10,000 per day at least, which requires a VPS rather than shared hosting). Here's my current setup with a paid mass-mailing software: I have a website - let's call it MyHostedDomain.org. I send newsletters with the From / Reply To address as [email protected], which isn't being hosting by me but I have access to the email account. Can I more or less safely set this up with an SMTP server on a VPS? i.e. send messages using [email protected] as the visible address, but having it all go through my VPS SMTP? I cannot authenticate it, right? Is this too risky a practice? Is my only hope to use an address with a domain on the VPS, i.e. [email protected]? I already have a Reverse DNS record for the domain hosted on my current VPS. I also see other suggestions, like SenderID and DKIM. But with all these things combined, will this still work? I don't want to get blacklisted, but the good thing is this is a somewhat private list, and users opt-in to subscribe. So it's a self-made audience. (If it makes you feel better, this is related to a non-profit activity, not some marketing scam...it's for a good cause, I assure you!)

  Read the article

• Hard Disk based storage library

  - by Ryan M.

  We have a Tandberg T24 tape device to handle all of our long term backups right now. We decided that we're not backing up nearly everything that we would like to and that we still have a lot of vulnerabilities. To get to where we want to be, we're going to have to back up a lot more servers than we're currently doing. All of our internal servers have some sort of directly attached drive (I.e. LaCie Raid box or a simple portable hard drive) doing backups, but what we want to do is get those backups off-site. The current tape drive is directly attached via SCSI to a Windows Server 2008 File Server. So to back up anything to tape, it has to be funneled through the File Server. With the current increase that we have planned, I don't think that funneling everything through the File Server is the right course of action and I'm thinking that maybe a second backup device would be more appropriate. I would like your input on a couple of ideas. 1) Doing HDD instead of tape. Tape is hard to deal with. We have a regular rotation cycle, so they don't need years and years of shelf life, so I'm wondering if something HDD-based would be better. 2) Something accessible over the network. Instead of having the device directly attached to one specific machine, have it available to all the servers over the network. Our File Server is a 12-disk raid 6 set up.. I was thinking something like that, but with no raid involved, all disks are stand alone so they can be used/installed/removed on an individual basis. Does any such thing exist? Thanks for your ideas. I'm really interested to hear about some of the solutions you guys are using..

  Read the article

• Save and restore multiple layers within a Photoshop action that flattens

  - by SuitCase

  I'm editing comic pages with layers - "background", "foreground", "lineart" and "over lineart". I have a Photoshop action that includes a Mode-Bitmap command, which requires the image to be flattened. I need this part of the action because I use the Halftone Screen method of reducing the greyscale image to bitmap on the "background" layer, creating a certain effect. I am pretty sure there is no filter or anything else that gives the same effect. After the mode is changed to bitmap, my action changes things back to greyscale for further changes. This poses a problem. I only want to do the bitmap mode change on the background layer, and after I do the change I want to restore the layer structure as it was - with the foreground, lineart and over lineart layers back above the now-halftoned background. My current method of saving these layers and restoring them is clumsy. My action is able to automatically save the "foreground" layer by selecting it, cutting it, then pasting it back in after the mode changing is over. But, for the "ink" and "over ink" layers, I have to manually cut these layers, paste them into a new document, and later re-cut and re-paste after running my action. This is so clunky! What I would like to know is if it's possible to set aside my layers in an automated way, and then bring them back in, also in an automated way. An ugly (but functional) solution would be to replicate my actions of creating new documents and pasting them temporarily there, but I don't think Photoshop allows you to do things outside of your current document with an action. It seems to me that the only way to do what I want is to use the "hack" of incorporating the clipboard into the action as a clever hack, but that leaves me stuck as I have two more layers that can't fit onto that same clipboard. Help or suggestions would be appreciated. I can keep on doing it manually, but to have a comprehensive action would save me a ton of time.

  Read the article

• Full Apache config migration

  - by Victor Rashkov

  I searched alot and didn't find an applicable answer. I have a working LAMP setup on Ubuntu machine and I have to migrate to a new server in a different country. The old server is 11.10, the new server is 12.04LTS. My problem is that I simply can not remember the steps I followed when I configured the current server which is not the basic LAMP install. It is Apache with FastCGI, SuEXEC, a GD library, worker MPM and all sitting on top of a mhddfs system. There are also other configs I've changed and I can not recall what they are. Because of the complexity of the setup, my attempts to migrate to the new server fail. I get permissions errors, cgi problems etc. Therefore my question is : Is there a sane way to simply tar a full backup of the current web server installation, including MySQL, Php amd the apache server with all configs, and then move it to the new machine? I shall be forever thankful on any advise. So far non of thise I found here gave me an answer. Thanks!

  Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >