Search Results

Search found 19018 results on 761 pages for 'basic disk'.

Page 156/761 | < Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >

• Install Ubuntu side by side with Windows

  - by Igal

  I'm trying to setup both Windows 7 and Ubuntu 14.04 Desktop on the same machine. I've partitioned the disk into 3 parts, so that I can have Windows Ubuntu Shared Partition for Files I've installed Windows 7 on the first partition (which created a small partition of 100MB for boot), so now I have 4 partitions on the disk which is all it can take. Now I am installing Ubuntu, and it's asking me whether I want to: Install Ubuntu inside Windows 7 Replace Windows 7 with Ubuntu (No!) Something else I want the Ubuntu installation to go into the partition that I prepared for it. Should I choose "Something else"? If I do so -- will I be able to choose which OS to load at boot? Can anyone explain how "Ubuntu inside Windows" work? it says that it will allow me to choose which OS to load at boot, which is desired. UPDATE: When choosing "Something else" I see also an option for Device for Boot Loader Installation: /dev/sda -- the ssd disk itself /dev/sda1 -- the Windows 7 loader (100MB partition) /dev/sda4 -- which is one of the other partitions Which one should I choose there? TIA!

  Read the article

• Can't start system due to mdadm failing

  - by user101212

  I used to have a 5-disk RAID5 partition, all working very well. I have then decided to add 3 more disks on it, totaling 8 equal disks. I've opened Webmin and just asked to add the disks. Then I've realized the three disks had NTFS partitions, wich mdadm didn't complain, so I tried to stop the growing to remove the Windows partitions. I've tried to remove a disk using the same Webmin, but (as you might guess and call me fool...), the system became unstable. By restarting the system, I've started receiving these messages: "udev[126]: timeout: killing '/sbin/mdadm --incremental /dev/sdh1' [311]" "udev[124]: timeout: killing '/sbin/mdadm --detail --export /dev/md0' [316]" I've formated the system disk, hoping to get a system up and running. I did that with all RAID disks disconected, so everything was fine. I then reconnected the disks, wich was also ok. And finally installed mdadm using apt-get. By reboot, the system has found the mdadm intention of growing the system, so the same messages appear again. I other words: I can't even reach a command prompt to do something. Any ideas of what to do? I believe I could turn off the system, disconnect the disks and look for the mdadm.conf file. Would that be a good idead? I'm no Linux expert, so I'm really lost here.

  Read the article

• How do I add a boot from cd option to yaboot?

  - by Sergiu

  So I'm dual-booting Ubuntu 12.04.1 on my iMac G5 powepc alongside Mac OS X and I want to add a boot cd option to yaboot because I'm trying to boot a scratched Mac OS X installation DVD that takes a while to read and the frst bootstrap moves on too fast. How do I edit the timeout for the first bootstrap anyways? So, my main question is, how do I add a cd booting option to yaboot and then, how doI boot it? The devalias from OpenFrmware tells me that 1 have 2 cd-rom instaled, on is /ht/pci@3/ata-6/disk@0 and the other on ends with a 1 instead of a zero. These are the contents of my yaboot.conf file: yaboot.conf generated by the Ubuntu installer run: "man yaboot.conf" for details. Do not make changes until you have!! see also: /usr/share/doc/yaboot/examples for example configurations. For a dual-boot menu, add one or more of: bsd=/dev/hdaX, macos=/dev/hdaY, macosx=/dev/hdaZ boot="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part2" device=/ht@0,f2000000/pci@3/k2-sata-root@c/@0/@0 partition=4 root="UUID=798a048f-ee48-49e0-bba3-111aed8dee04" timeout=12000 install=/usr/lib/yaboot/yaboot magicboot=/usr/lib/yaboot/ofboot enablecdboot macosx="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part3" image=/boot/vmlinux label=Linux read-only initrd=/boot/initrd.img append="quiet splash" What do I add here so that yaboot will boot from my cd in like 3 minutes after startup? Thanks!

  Read the article

• Can anyone point me to some open source directX rendering engines or frameworks? [on hold]

  - by Jim

  I'm completely new to graphics API programmming, but not at all new to the theory and principle operation of game engines and rendering engines. That being said, I want to do some experiments of rendering very dense geometry scenes in a basic rendering engine or game engine. I don't need a lot of bells and whistles. What I need is enough control that I can implement my own scene graph algorithms and control the rendering pipeline very specifically. My ideal candidate engine would be either a rendering engine or game engine with a modular design that might be ready to go out of the box but would be simple enough in case I need to rip out some of the guts in the rendering management and implement my own. It's a tough call because I'm right at the level where it's almost better to go from scratch, but there's no sense in having to build every single basic thing such as heirarchical transforms, etc. I just want to work with rendering optimization to push dense geometry for maximum FPS. Does anyone have a suggestion for an engine or basic framework to use? I requested DirectX in my title because I figured it would likely be better supported and less likely for me to run into some obscure less-documented problem. But OpenGL might be acceptable if the recommended framework was definitely better than my other options. EDIT: I should add that I really want GPU tessellation support (part of adding to the density of geometry detail).

  Read the article

• Will Ubuntu Live CD move MFT to resize NTFS volumes?

  - by irwazr

  I have a feeling some will consider this a duplicate, but please hear me out. I've been reading tons of questions and threads around this but have never really found an answer for this specifically. I want to shrink my NTFS partition to make room for a Ubuntu install, so I can dual boot them. However when shrinking the NTFS volume in Windows disk management, it will only go so far as the MFT is sitting near the end of the volume. I've read plenty of posts about why it does this, and how difficult/dangerous it is to move the MFT etc. I've also read that Perfect Disk can apparently do it under it's trial period, but I remain cautious to try this method. I was wondering however if the disk partitioning utility included in the Ubuntu install wizard handles the moving of the MFT when dragging the partition boundaries. It all seems too simple that you simply tell it the new size you want it to be. Would it tell me if it couldn't resize by the amount you requested if the MFT was an issue, or move it for you if it were able. I'm concerned it might corrupt the MFT and the volume, even though I doubt the install wizard would be so daft. So what exactly is the deal with the partition resizing tool in the Ubuntu install wizard? Will it safely resize my NTFS volume despite the location of my MFT? Thanks in advance.

  Read the article

• Ubuntu cannot see Windows 7 partitions on install

  - by Nash0

  I've been trying to install Ubuntu 10.10 as a dual boot with Windows 7 on my Dell latitude e6510. It is currently running Windows 7 and I have used the MS disk tools to shrink the Win 7 NTFS partition to make room for Linux. The issue I'm having is that when I run Ubuntus installer by booting from CD it sees the entire hard drive as unallocated space. I have also tried Kbuntu 10.10, Fedora 14, booting a Gparted 0.8.0 usb drive, and Ubuntu "install in Windows" with wubi they all have problems. EDIT: When I run the "try Ubuntu" option on booting from cd it can mount my Windows partition and I can view the files. The output of sudo parted -l when running in try Ubuntu mode: Warning: /dev/sda contains GPT signatures, indicating that it has a GPT table. However, it does not have a valid fake msdos partition table, as it should. Perhaps it was corrupted -- possibly by a program that doesn't understand GPT partition tables. Or perhaps you deleted the GPT table, and are now using an msdos partition table. Is this a GPT partition table? Yes/No? yes Model: ATA ST9500420AS (scsi) Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• Grub2 cannot detect Windows 8

  - by MetaChrome

  At installation it did not detect Windows. I mounted the Windows partition and have run os-prober with no results returning. I am able to boot Windows or Ubuntu by specifying the partition in UEFI boot order. The bios does not appear to allow booting with legacy. SecureBoot is on. This is with Ubuntu 12.04 LTS on a Inspiron 15. Here is the gdisk: 1 2048 1026047 500.0 MiB EF00 EFI system partition 2 1026048 1107967 40.0 MiB FFFF Basic data partition 3 1107968 1370111 128.0 MiB 0C01 Microsoft reserved part 4 1370112 2394111 500.0 MiB 2700 Basic data partition 5 2394112 544743423 258.6 GiB 0700 Basic data partition 6 606183424 625140399 9.0 GiB 2700 Microsoft recovery part 7 544743424 545230847 238.0 MiB 0700 (/boot) 8 545230848 556949503 5.6 GiB 8200 (swap) 9 556949504 606181375 23.5 GiB 0700 (/) When installing ubuntu, I believe I specified that the bootloader be installed on /dev/sda. I added the following to /etc/grub.d/40_custom but booting ubuntu did not offer a grub menu: menuentry "Windows 8" { set root = "(hd0,4)" chainloader +1 } When booting I think I see "EFI Disk error" flash very quickly before Ubuntu starts booting.

  Read the article

• Thunderbird: "Could not initialize the application's security component" [closed]

  - by user unknown

  In Thunderbird, on startup, I get the error message: "Could not initialize the application's security component" The message continues to check permissions of the profile, and free disk space. df -h shows, that I have 19G free disk space. find . -not -perm -644 -not -perm -600 -ls shows: No file without rw-permissions for me. Before the error occured, thunderbird worked well. But I changed my main mail-account. I had two, let's call them A and B, and used mainly A, but now I wanted to deaktivate it, and receive and send automatically via the second. I Had problems moving the filters from inbox A to inbox B (missing copy-functionality). In the web, I found (mollazine) hints, to move key3.db, cert8.db and secmode.db out of the way, but it didn't work for me. Another hint was to uninstall Quickcam(?. sic!), but I don't have Quickcam. A third to recreate the profile, but I have subdirectories, filters, addressbook, groups - mails back to the year 2003. I don't want to risk the loss of data. The whole errormessage is: Could not initialize the application's security component. The most likely cause is problems with files in your application's profile directory. Please check that this directory has no read/write restrictions and your hard disk is not full or close to full. It is recommended that you exit the application and fix the problem. If you continue to use this session, you might see incorrect application behaviour when accessing security features. When I open the error-console, it is empty.

  Read the article

• How do I get my internal HDD to mount at startup?

  - by el_gallo_azul

  It's either not intuitive or not working in Ubuntu 14.04. I want to mount my internal HDD at at startup (I boot from an SSD). I attempt to set this, following this procedure: Open Disks utility Select the disk Below the disk's Volumes, click on the More actions button Select Edit Mount Options... Select Automatic Mount Options "Off" Under Mount Options, ensure that Mount at startup is selected Click OK Enter password into Authenticate dialog box Restart but this procedure doesn't work. Upon rebooting, and after Grub attempts to start Ubuntu, I receive the error message "An error occurred while mounting /mnt/4f721fc0-8072-453f-b48f-ca686bd89549. Press S to skip mounting or M for manual recovery". That identifier "4f721fc0-8072-453f-b48f-ca686bd89549" was automatically assigned by Ubuntu. I press S and the boot process continues OK. If I try to mount the disk immediately after booting, I receive the error message "Unable to access "Storage"" (I named the volume Storage). So then I start the Disks utility and set it to Automatic Mount Options "On" and reboot. To me, it seems like this should work, but it doesn't. Here are a number of photos of the process (Alt+PrtScn doesn't work after selecting More actions).

  Read the article

• How should a non-IT manager secure the long-term maintenance and development of essential legacy software?

  - by user105977

  I've been hunting for a place to ask this question for quite a while; maybe this is the place, although I'm afraid it's not the kind of "question with an answer" this site would prefer. We are a small, very specialized, benefits administration firm with an extremely useful, robust collection of software, some written in COBOL but most in BASIC. Two full-time consultants have ably maintained and improved this system over more than 30 years. Needless to say they will soon retire. (One of them has been desperate to retire for several years but is loyal to a fault and so hangs on despite her husband's insistence that golf should take priority.) We started down the path of converting to a system developed by one of only three firms in the country that offer the type of software we use. We now feel that although this this firm is theoretically capable of completing the conversion process, they don't have the resources to do so timely, and we have come to believe that they will be unable to offer the kind of service we need to run our business. (There's nothing like being able to set one's own priorities and having the authority to allocate one's resources as one sees fit.) Hardware is not a problem--we are able to emulate very effectively on modern servers. If COBOL and BASIC were modern languages, we'd be willing to take the risk that we could find replacements for our current consultants going forward. It seems like there ought to be a business model for an IT support firm that concentrates on legacy platforms like this and provides the programming and software development talent to support a system like ours, removing from our backs the risks of finding the right programming talent and the job of convincing younger programmers that they can have a productive, rewarding career, in part in an old, non-sexy language like BASIC. Where do I find such firms?

  Read the article

• Putting update logic in your migrations

  - by Daniel Abrahamsson

  A couple of times I've been in the situation where I've wanted to refactor the design of some model and have ended up putting update logic in migrations. However, as far as I've understood, this is not good practice (especially since you are encouraged to use your schema file for deployment, and not your migrations). How do you deal with these kind of problems? To clearify what I mean, say I have a User model. Since I thought there would only be two kinds of users, namely a "normal" user and an administrator, I chose to use a simple boolean field telling whether the user was an adminstrator or not. However, after I while I figured I needed some third kind of user, perhaps a moderator or something similar. In this case I add a UserType model (and the corresponding migration), and a second migration for removing the "admin" flag from the user table. And here comes the problem. In the "add_user_type_to_users" migration I have to map the admin flag value to a user type. Additionally, in order to do this, the user types have to exist, meaning I can not use the seeds file, but rather create the user types in the migration (also considered bad practice). Here comes some fictional code representing the situation: class CreateUserTypes < ActiveRecord::Migration def self.up create_table :user_types do |t| t.string :name, :nil => false, :unique => true end #Create basic types (can not put in seed, because of future migration dependency) UserType.create!(:name => "BASIC") UserType.create!(:name => "MODERATOR") UserType.create!(:name => "ADMINISTRATOR") end def self.down drop_table :user_types end end class AddTypeIdToUsers < ActiveRecord::Migration def self.up add_column :users, :type_id, :integer #Determine type via the admin flag basic = UserType.find_by_name("BASIC") admin = UserType.find_by_name("ADMINISTRATOR") User.all.each {|u| u.update_attribute(:type_id, (u.admin?) ? admin.id : basic.id)} #Remove the admin flag remove_column :users, :admin #Add foreign key execute "alter table users add constraint fk_user_type_id foreign key (type_id) references user_types (id)" end def self.down #Re-add the admin flag add_column :users, :admin, :boolean, :default => false #Reset the admin flag (this is the problematic update code) admin = UserType.find_by_name("ADMINISTRATOR") execute "update users set admin=true where type_id=#{admin.id}" #Remove foreign key constraint execute "alter table users drop foreign key fk_user_type_id" #Drop the type_id column remove_column :users, :type_id end end As you can see there are two problematic parts. First the row creation part in the first model, which is necessary if I would like to run all migrations in a row, then the "update" part in the second migration that maps the "admin" column to the "type_id" column. Any advice?

  Read the article

• Should I use Python or Assembly for a super fast copy program

  - by PyNEwbie

  As a maintenance issue I need to routinely (3-5 times per year) copy a repository that is now has over 20 million files and exceeds 1.5 terabytes in total disk space. I am currently using RICHCOPY, but have tried others. RICHCOPY seems the fastest but I do not believe I am getting close to the limits of the capabilities of my XP machine. I am toying around with using what I have read in The Art of Assembly Language to write a program to copy my files. My other thought is to start learning how to multi-thread in Python to do the copies. I am toying around with the idea of doing this in Assembly because it seems interesting, but while my time is not incredibly precious it is precious enough that I am trying to get a sense of whether or not I will see significant enough gains in copy speed. I am assuming that I would but I only started really learning to program 18 months and it is still more or less a hobby. Thus I may be missing some fundamental concept of what happens with interpreted languages. Any observations or experiences would be appreciated. Note, I am not looking for any code. I have already written a basic copy program in Python 2.6 that is no slower than RICHCOPY. I am looking for some observations on which will give me more speed. Right now it takes me over 50 hours to make a copy from a disk to a Drobo and then back from the Drobo to a disk. I have a LogicCube for when I am simply duplicating a disk but sometimes I need to go from a disk to Drobo or the reverse. I am thinking that given that I can sector copy a 3/4 full 2 terabyte drive using the LogicCube in under seven hours I should be able to get close to that using Assembly, but I don't know enough to know if this is valid. (Yes, sometimes ignorance is bliss) The reason I need to speed it up is I have had two or three cycles where something has happened during copy (fifty hours is a long time to expect the world to hold still) that has caused me to have to trash the copy and start over. For example, last week the water main broke under our building and shorted out the power.

  Read the article

• How can I limit the cache used by copying so there is still memory available for other cache?

  - by Peter

  Basic situation: I am copying some NTFS disks in openSuSE. Each one is 2TB. When I do this, the system runs slow. My guesses: I believe it is likely due to caching. Linux decides to discard useful cache (eg. kde4 bloat, virtual machine disks, LibreOffice binaries, Thunderbird binaries, etc.) and instead fill all available memory (24 GB total) with stuff from the copying disks, which will be read only once, then written and never used again. So then any time I use these apps (or kde4), the disk needs to be read again, and reading the bloat off the disk again makes things freeze/hiccup. Due to the cache being gone and the fact that these bloated applications need lots of cache, this makes the system horribly slow. Since it is USB,the disk and disk controller are not the bottleneck, so using ionice does not make it faster. I believe it is the cache rather than just the motherboard going too slow, because if I stop everything copying, it still runs choppy for a while until it recaches everything. And if I restart the copying, it takes a minute before it is choppy again. But also, I can limit it to around 40 MB/s, and it runs faster again (not because it has the right things cached, but because the motherboard busses have lots of extra bandwidth for the system disks). I can fully accept a performance loss from my motherboard's IO capability being completely consumed (which is 100% used, meaning 0% wasted power which makes me happy), but I can't accept that this caching mechanism performs so terribly in this specific use case. # free total used free shared buffers cached Mem: 24731556 24531876 199680 0 8834056 12998916 -/+ buffers/cache: 2698904 22032652 Swap: 4194300 24764 4169536 I also tried the same thing on Ubuntu, which causes a total system hang instead. ;) And to clarify, I am not asking how to leave memory free for the "system", but for "cache". I know that cache memory is automatically given back to the system when needed, but my problem is that it is not reserved for caching of specific things. Question: Is there some way to tell these copy operations to limit memory usage so some important things remain cached, and therefore any slowdowns are a result of normal disk usage and not rereading the same commonly used files? For example, is there a setting of max memory per process/user/file system allowed to be used as cache/buffers?

  Read the article

• Rails. Putting update logic in your migrations

  - by Daniel Abrahamsson

  A couple of times I've been in the situation where I've wanted to refactor the design of some model and have ended up putting update logic in migrations. However, as far as I've understood, this is not good practice (especially since you are encouraged to use your schema file for deployment, and not your migrations). How do you deal with these kind of problems? To clearify what I mean, say I have a User model. Since I thought there would only be two kinds of users, namely a "normal" user and an administrator, I chose to use a simple boolean field telling whether the user was an adminstrator or not. However, after I while I figured I needed some third kind of user, perhaps a moderator or something similar. In this case I add a UserType model (and the corresponding migration), and a second migration for removing the "admin" flag from the user table. And here comes the problem. In the "add_user_type_to_users" migration I have to map the admin flag value to a user type. Additionally, in order to do this, the user types have to exist, meaning I can not use the seeds file, but rather create the user types in the migration (also considered bad practice). Here comes some fictional code representing the situation: class CreateUserTypes < ActiveRecord::Migration def self.up create_table :user_types do |t| t.string :name, :nil => false, :unique => true end #Create basic types (can not put in seed, because of future migration dependency) UserType.create!(:name => "BASIC") UserType.create!(:name => "MODERATOR") UserType.create!(:name => "ADMINISTRATOR") end def self.down drop_table :user_types end end class AddTypeIdToUsers < ActiveRecord::Migration def self.up add_column :users, :type_id, :integer #Determine type via the admin flag basic = UserType.find_by_name("BASIC") admin = UserType.find_by_name("ADMINISTRATOR") User.all.each {|u| u.update_attribute(:type_id, (u.admin?) ? admin.id : basic.id)} #Remove the admin flag remove_column :users, :admin #Add foreign key execute "alter table users add constraint fk_user_type_id foreign key (type_id) references user_types (id)" end def self.down #Re-add the admin flag add_column :users, :admin, :boolean, :default => false #Reset the admin flag (this is the problematic update code) admin = UserType.find_by_name("ADMINISTRATOR") execute "update users set admin=true where type_id=#{admin.id}" #Remove foreign key constraint execute "alter table users drop foreign key fk_user_type_id" #Drop the type_id column remove_column :users, :type_id end end As you can see there are two problematic parts. First the row creation part in the first model, which is necessary if I would like to run all migrations in a row, then the "update" part in the second migration that maps the "admin" column to the "type_id" column. Any advice?

  Read the article

• How do I use a custom #theme function to a fieldset in a drupal module?

  - by Rob Crowell

  I have a module that builds a form that includes a fieldset. Instead of using the <legend> element to render the fieldset title, I want to place this content in a <div> element instead. But I want to change the behavior only for the form returned by my module, so I don't want to place any new functionality into my theme's template.php file. In mymod.module I have defined: // custom rendering function for fieldset elements function theme_mymod_fieldset($element) { return 'test'; } // implement hook_theme function mymod_theme() { return array( 'mymod_fieldset' => array('arguments' => array('element' => NULL)), 'mymod_form' => array('arguments' => array()) ); } // return a form that is based on the 'Basic Account Info' category of the user profile function mymod_form() { // load the user's profile global $user; $account = user_load($user->uid); // load the profile form, and then edit it $form_state = array(); $form = drupal_retrieve_form('user_profile_form', $form_state, $account, 'Basic Account Info'); // set the custom #theme function for this fieldset $form['Basic Account Info']['#theme'] = 'mymod_fieldset'; // more form manipulations // ... return $form; } When my page gets rendered, I expected to see the fieldset representing 'Basic Account Info' to be wholly replaced by my test message 'test'. Instead what happens is that the <fieldset> and <legend> elements are rendered as normal, but with the body of the fieldset replaced by the test message instead, like this: <fieldset> <legend>Basic Account Info</legend> test </fieldset> Why doesn't my #theme function have the chance to replace the entire <fieldset> element? If I wrap a textfield in this function instead, I am able to completely replace the <input> element along with its label. Furthermore, if I provide an override in my site's template.php for theme_fieldset, it works as expected and I am able to completely replace the <fieldset>, so I know it is possible. What's different about providing #theme functions to fieldsets inside a module?

  Read the article

• "domain crashed" when creating new Xen instance

  - by user47650

  I have downloaded a Xen virtual machine image from the appscale project, and I am trying to start it up. However once I run the command; xm create -c -f xen.conf The instance immediately crashes and provides no console output. however it produces logs that I have posted below. but this is the error; [2011-03-01 12:34:03 xend.XendDomainInfo 3580] WARNING (XendDomainInfo:1178) Domain has crashed: name=appscale-1.4b id=10. I have managed to mount the root.img file locally and verify that it is actually an ext3 file system. I am running Xen 3.0.3 that is a stock RPM from the CentOS 5 repos; # rpm -qa | grep -i xen xen-libs-3.0.3-105.el5_5.5 xen-3.0.3-105.el5_5.5 xen-libs-3.0.3-105.el5_5.5 kernel-xen-2.6.18-194.32.1.el5 any suggestions on how to proceed with troubleshooting? (i am a newbie to Xen) so far I have enabled console logging, but the log file is empty. ==> domain-builder-ng.log <== xc_dom_allocate: cmdline=" ip=:1.2.3.4::::eth0:dhcp root=/dev/sda1 ro xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console", features="" xc_dom_kernel_file: filename="/boot/vmlinuz-2.6.27-7-server" xc_dom_malloc_filemap : 2284 kB xc_dom_ramdisk_file: filename="/boot/initrd.img-2.6.27-7-server" xc_dom_malloc_filemap : 9005 kB xc_dom_boot_xen_init: ver 3.1, caps xen-3.0-x86_64 xen-3.0-x86_32p xc_dom_parse_image: called xc_dom_find_loader: trying ELF-generic loader ... failed xc_dom_find_loader: trying Linux bzImage loader ... xc_dom_malloc : 9875 kB xc_dom_do_gunzip: unzip ok, 0x234bb2 -> 0x9a4de0 OK elf_parse_binary: phdr: paddr=0x200000 memsz=0x447000 elf_parse_binary: phdr: paddr=0x647000 memsz=0xab888 elf_parse_binary: phdr: paddr=0x6f3000 memsz=0x908 elf_parse_binary: phdr: paddr=0x6f4000 memsz=0x1c2f9c elf_parse_binary: memory: 0x200000 -> 0x8b6f9c elf_xen_parse_note: GUEST_OS = "linux" elf_xen_parse_note: GUEST_VERSION = "2.6" elf_xen_parse_note: XEN_VERSION = "xen-3.0" elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 elf_xen_parse_note: ENTRY = 0xffffffff8071e200 elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80209000 elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" elf_xen_parse_note: PAE_MODE = "yes" elf_xen_parse_note: LOADER = "generic" elf_xen_parse_note: unknown xen elf note (0xd) elf_xen_parse_note: SUSPEND_CANCEL = 0x1 elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 elf_xen_parse_note: PADDR_OFFSET = 0x0 elf_xen_addr_calc_check: addresses: virt_base = 0xffffffff80000000 elf_paddr_offset = 0x0 virt_offset = 0xffffffff80000000 virt_kstart = 0xffffffff80200000 virt_kend = 0xffffffff808b6f9c virt_entry = 0xffffffff8071e200 xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff80200000 -> 0xffffffff808b6f9c xc_dom_mem_init: mem 1024 MB, pages 0x40000 pages, 4k each xc_dom_mem_init: 0x40000 pages xc_dom_boot_mem_init: called x86_compat: guest xen-3.0-x86_64, address size 64 xc_dom_malloc : 2048 kB ==> xend.log <== [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:01 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:02 xend.XendDomainInfo 3580] INFO (XendDomainInfo:957) Dev 0 still active, looping... [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2114) UUID Created: True [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2115) Devices to release: [], domid = 9 [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2127) Releasing PVFB backend devices ... [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:207) XendDomainInfo.create(['domain', ['domid', 9], ['uuid', 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0'], ['vcpus', 1], ['vcpu_avail', 1], ['cpu_cap', 0], ['cpu_weight', 256], ['memory', 1024], ['shadow_memory', 0], ['maxmem', 1024], ['features', ''], ['name', 'appscale-1.4b'], ['on_poweroff', 'destroy'], ['on_reboot', 'restart'], ['on_crash', 'restart'], ['image', ['linux', ['kernel', '/boot/vmlinuz-2.6.27-7-server'], ['ramdisk', '/boot/initrd.img-2.6.27-7-server'], ['ip', ':1.2.3.4::::eth0:dhcp'], ['root', '/dev/sda1 ro'], ['args', 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console']]], ['cpus', []], ['device', ['vif', ['backend', 0], ['script', 'vif-bridge'], ['mac', '00:16:3B:72:10:E4']]], ['device', ['vbd', ['backend', 0], ['dev', 'sda1:disk'], ['uname', 'file:/local/xen/domains/appscale1.4/root.img'], ['mode', 'w']]], ['state', '----c-'], ['shutdown_reason', 'crash'], ['cpu_time', 0.000339131], ['online_vcpus', 1], ['up_time', '0.952092885971'], ['start_time', '1299011639.92'], ['store_mfn', 1169289], ['console_mfn', 1169288]]) [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:329) parseConfig: config is ['domain', ['domid', 9], ['uuid', 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0'], ['vcpus', 1], ['vcpu_avail', 1], ['cpu_cap', 0], ['cpu_weight', 256], ['memory', 1024], ['shadow_memory', 0], ['maxmem', 1024], ['features', ''], ['name', 'appscale-1.4b'], ['on_poweroff', 'destroy'], ['on_reboot', 'restart'], ['on_crash', 'restart'], ['image', ['linux', ['kernel', '/boot/vmlinuz-2.6.27-7-server'], ['ramdisk', '/boot/initrd.img-2.6.27-7-server'], ['ip', ':1.2.3.4::::eth0:dhcp'], ['root', '/dev/sda1 ro'], ['args', 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console']]], ['cpus', []], ['device', ['vif', ['backend', 0], ['script', 'vif-bridge'], ['mac', '00:16:3B:72:10:E4']]], ['device', ['vbd', ['backend', 0], ['dev', 'sda1:disk'], ['uname', 'file:/local/xen/domains/appscale1.4/root.img'], ['mode', 'w']]], ['state', '----c-'], ['shutdown_reason', 'crash'], ['cpu_time', 0.000339131], ['online_vcpus', 1], ['up_time', '0.952092885971'], ['start_time', '1299011639.92'], ['store_mfn', 1169289], ['console_mfn', 1169288]] [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:446) parseConfig: result is {'features': '', 'image': ['linux', ['kernel', '/boot/vmlinuz-2.6.27-7-server'], ['ramdisk', '/boot/initrd.img-2.6.27-7-server'], ['ip', ':1.2.3.4::::eth0:dhcp'], ['root', '/dev/sda1 ro'], ['args', 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console']], 'cpus': [], 'vcpu_avail': 1, 'backend': [], 'uuid': 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0', 'on_reboot': 'restart', 'cpu_weight': 256.0, 'memory': 1024, 'cpu_cap': 0, 'localtime': None, 'timer_mode': None, 'start_time': 1299011639.9200001, 'on_poweroff': 'destroy', 'on_crash': 'restart', 'device': [('vif', ['vif', ['backend', 0], ['script', 'vif-bridge'], ['mac', '00:16:3B:72:10:E4']]), ('vbd', ['vbd', ['backend', 0], ['dev', 'sda1:disk'], ['uname', 'file:/local/xen/domains/appscale1.4/root.img'], ['mode', 'w']])], 'bootloader': None, 'maxmem': 1024, 'shadow_memory': 0, 'name': 'appscale-1.4b', 'bootloader_args': None, 'vcpus': 1, 'cpu': None} [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1784) XendDomainInfo.construct: None [2011-03-01 12:34:02 xend 3580] DEBUG (balloon:145) Balloon: 3034420 KiB free; need 4096; done. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1953) XendDomainInfo.initDomain: 10 256.0 [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1994) _initDomain:shadow_memory=0x0, maxmem=0x400, memory=0x400. [2011-03-01 12:34:02 xend 3580] DEBUG (balloon:145) Balloon: 3034412 KiB free; need 1048576; done. [2011-03-01 12:34:02 xend 3580] INFO (image:139) buildDomain os=linux dom=10 vcpus=1 [2011-03-01 12:34:02 xend 3580] DEBUG (image:208) domid = 10 [2011-03-01 12:34:02 xend 3580] DEBUG (image:209) memsize = 1024 [2011-03-01 12:34:02 xend 3580] DEBUG (image:210) image = /boot/vmlinuz-2.6.27-7-server [2011-03-01 12:34:02 xend 3580] DEBUG (image:211) store_evtchn = 1 [2011-03-01 12:34:02 xend 3580] DEBUG (image:212) console_evtchn = 2 [2011-03-01 12:34:02 xend 3580] DEBUG (image:213) cmdline = ip=:1.2.3.4::::eth0:dhcp root=/dev/sda1 ro xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console [2011-03-01 12:34:02 xend 3580] DEBUG (image:214) ramdisk = /boot/initrd.img-2.6.27-7-server [2011-03-01 12:34:02 xend 3580] DEBUG (image:215) vcpus = 1 [2011-03-01 12:34:02 xend 3580] DEBUG (image:216) features = ==> domain-builder-ng.log <== xc_dom_build_image: called xc_dom_alloc_segment: kernel : 0xffffffff80200000 -> 0xffffffff808b7000 (pfn 0x200 + 0x6b7 pages) xc_dom_pfn_to_ptr: domU mapping: pfn 0x200+0x6b7 at 0x2aaaab5f6000 elf_load_binary: phdr 0 at 0x0x2aaaab5f6000 -> 0x0x2aaaaba3d000 elf_load_binary: phdr 1 at 0x0x2aaaaba3d000 -> 0x0x2aaaabae8888 elf_load_binary: phdr 2 at 0x0x2aaaabae9000 -> 0x0x2aaaabae9908 elf_load_binary: phdr 3 at 0x0x2aaaabaea000 -> 0x0x2aaaabb9a004 xc_dom_alloc_segment: ramdisk : 0xffffffff808b7000 -> 0xffffffff82382000 (pfn 0x8b7 + 0x1acb pages) xc_dom_malloc : 160 kB xc_dom_pfn_to_ptr: domU mapping: pfn 0x8b7+0x1acb at 0x2aaab0000000 xc_dom_do_gunzip: unzip ok, 0x8cb5e7 -> 0x1aca210 xc_dom_alloc_segment: phys2mach : 0xffffffff82382000 -> 0xffffffff82582000 (pfn 0x2382 + 0x200 pages) xc_dom_pfn_to_ptr: domU mapping: pfn 0x2382+0x200 at 0x2aaab1acb000 xc_dom_alloc_page : start info : 0xffffffff82582000 (pfn 0x2582) xc_dom_alloc_page : xenstore : 0xffffffff82583000 (pfn 0x2583) xc_dom_alloc_page : console : 0xffffffff82584000 (pfn 0x2584) nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) xc_dom_alloc_segment: page tables : 0xffffffff82585000 -> 0xffffffff8259c000 (pfn 0x2585 + 0x17 pages) xc_dom_pfn_to_ptr: domU mapping: pfn 0x2585+0x17 at 0x2aaab1ccb000 xc_dom_alloc_page : boot stack : 0xffffffff8259c000 (pfn 0x259c) xc_dom_build_image : virt_alloc_end : 0xffffffff8259d000 xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 xc_dom_boot_image: called arch_setup_bootearly: doing nothing xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches xc_dom_compat_check: supported guest type: xen-3.0-x86_32p xc_dom_update_guest_p2m: dst 64bit, pages 0x40000 clear_page: pfn 0x2584, mfn 0x11d788 clear_page: pfn 0x2583, mfn 0x11d789 xc_dom_pfn_to_ptr: domU mapping: pfn 0x2582+0x1 at 0x2aaab1ce2000 start_info_x86_64: called setup_hypercall_page: vaddr=0xffffffff80209000 pfn=0x209 domain builder memory footprint allocated malloc : 12139 kB anon mmap : 0 bytes mapped file mmap : 11289 kB domU mmap : 35 MB arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xd6fe1 shared_info_x86_64: called vcpu_x86_64: called vcpu_x86_64: cr3: pfn 0x2585 mfn 0x11d787 launch_vm: called, ctxt=0x97b21f8 xc_dom_release: called ==> xend.log <== [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:114) DevController: writing {'mac': '00:16:3B:72:10:E4', 'handle': '0', 'protocol': 'x86_64-abi', 'backend-id': '0', 'state': '1', 'backend': '/local/domain/0/backend/vif/10/0'} to /local/domain/10/device/vif/0. [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:116) DevController: writing {'domain': 'appscale-1.4b', 'handle': '0', 'script': '/etc/xen/scripts/vif-bridge', 'state': '1', 'frontend': '/local/domain/10/device/vif/0', 'mac': '00:16:3B:72:10:E4', 'online': '1', 'frontend-id': '10'} to /local/domain/0/backend/vif/10/0. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:634) Checking for duplicate for uname: /local/xen/domains/appscale1.4/root.img [file:/local/xen/domains/appscale1.4/root.img], dev: sda1:disk, mode: w [2011-03-01 12:34:02 xend 3580] DEBUG (blkif:27) exception looking up device number for sda1:disk: [Errno 2] No such file or directory: '/dev/sda1:disk' [2011-03-01 12:34:02 xend 3580] DEBUG (blkif:27) exception looking up device number for sda1: [Errno 2] No such file or directory: '/dev/sda1' [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:114) DevController: writing {'virtual-device': '2049', 'device-type': 'disk', 'protocol': 'x86_64-abi', 'backend-id': '0', 'state': '1', 'backend': '/local/domain/0/backend/vbd/10/2049'} to /local/domain/10/device/vbd/2049. [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:116) DevController: writing {'domain': 'appscale-1.4b', 'frontend': '/local/domain/10/device/vbd/2049', 'format': 'raw', 'dev': 'sda1', 'state': '1', 'params': '/local/xen/domains/appscale1.4/root.img', 'mode': 'w', 'online': '1', 'frontend-id': '10', 'type': 'file'} to /local/domain/0/backend/vbd/10/2049. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:993) Storing VM details: {'shadow_memory': '0', 'uuid': 'd5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0', 'on_reboot': 'restart', 'start_time': '1299011642.74', 'on_poweroff': 'destroy', 'name': 'appscale-1.4b', 'xend/restart_count': '0', 'vcpus': '1', 'vcpu_avail': '1', 'memory': '1024', 'on_crash': 'restart', 'image': "(linux (kernel /boot/vmlinuz-2.6.27-7-server) (ramdisk /boot/initrd.img-2.6.27-7-server) (ip :1.2.3.4::::eth0:dhcp) (root '/dev/sda1 ro') (args 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console'))", 'maxmem': '1024'} [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1028) Storing domain details: {'console/ring-ref': '1169288', 'console/port': '2', 'name': 'appscale-1.4b', 'console/limit': '1048576', 'vm': '/vm/d5f22dd4-8dc2-f51f-84e9-eea7d71ea1d0', 'domid': '10', 'cpu/0/availability': 'online', 'memory/target': '1048576', 'store/ring-ref': '1169289', 'store/port': '1'} [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:158) Waiting for devices vif. [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:164) Waiting for 0. [2011-03-01 12:34:02 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:1250) XendDomainInfo.handleShutdownWatch [2011-03-01 12:34:02 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vif/10/0/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vif/10/0/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:523) hotplugStatusCallback 1. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices usb. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vbd. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:164) Waiting for 2049. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vbd/10/2049/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:509) hotplugStatusCallback /local/domain/0/backend/vbd/10/2049/hotplug-status. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:523) hotplugStatusCallback 1. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices irq. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vkbd. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vfb. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices pci. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices ioports. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices tap. [2011-03-01 12:34:03 xend 3580] DEBUG (DevController:158) Waiting for devices vtpm. [2011-03-01 12:34:03 xend.XendDomainInfo 3580] WARNING (XendDomainInfo:1178) Domain has crashed: name=appscale-1.4b id=10. [2011-03-01 12:34:03 xend.XendDomainInfo 3580] ERROR (XendDomainInfo:2654) VM appscale-1.4b restarting too fast (2.275545 seconds since the last restart). Refusing to restart to avoid loops. [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2189) XendDomainInfo.destroy: domid=10 ==> xen-hotplug.log <== Nothing to flush. ==> xend.log <== [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] INFO (XendDomainInfo:2330) Dev 2049 still active, looping... [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2114) UUID Created: True [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2115) Devices to release: [], domid = 10 [2011-03-01 12:34:03 xend.XendDomainInfo 3580] DEBUG (XendDomainInfo:2127) Releasing PVFB backend devices ... And this is the xen.conf file that I am using; # cat xen.conf # Configuration file for the Xen instance AppScale, created # bn VMBuilder kernel = '/boot/vmlinuz-2.6.27-7-server' ramdisk = '/boot/initrd.img-2.6.27-7-server' memory = 1024 vcpus = 1 root = '/dev/sda1 ro' disk = [ 'file:/local/xen/domains/appscale1.4/root.img,sda1,w', ] name = 'appscale-1.4b' dhcp = 'dhcp' vif = [ 'mac=00:16:3B:72:10:E4' ] on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' extra = 'xencons=tty console=tty1 console=hvc0 debugger=y debug=y sync_console'

  Read the article

• Squid + Dans Guardian (simple configuration)

  - by The Digital Ninja

  I just built a new proxy server and compiled the latest versions of squid and dansguardian. We use basic authentication to select what users are allowed outside of our network. It seems squid is working just fine and accepts my username and password and lets me out. But if i connect to dans guardian, it prompts for username and password and then displays a message saying my username is not allowed to access the internet. Its pulling my username for the error message so i know it knows who i am. The part i get confused on is i thought that part was handled all by squid, and squid is working flawlessly. Can someone please double check my config files and tell me if i'm missing something or there is some new option i must set to get this to work. dansguardian.conf # Web Access Denied Reporting (does not affect logging) # # -1 = log, but do not block - Stealth mode # 0 = just say 'Access Denied' # 1 = report why but not what denied phrase # 2 = report fully # 3 = use HTML template file (accessdeniedaddress ignored) - recommended # reportinglevel = 3 # Language dir where languages are stored for internationalisation. # The HTML template within this dir is only used when reportinglevel # is set to 3. When used, DansGuardian will display the HTML file instead of # using the perl cgi script. This option is faster, cleaner # and easier to customise the access denied page. # The language file is used no matter what setting however. # languagedir = '/etc/dansguardian/languages' # language to use from languagedir. language = 'ukenglish' # Logging Settings # # 0 = none 1 = just denied 2 = all text based 3 = all requests loglevel = 3 # Log Exception Hits # Log if an exception (user, ip, URL, phrase) is matched and so # the page gets let through. Can be useful for diagnosing # why a site gets through the filter. on | off logexceptionhits = on # Log File Format # 1 = DansGuardian format 2 = CSV-style format # 3 = Squid Log File Format 4 = Tab delimited logfileformat = 1 # Log file location # # Defines the log directory and filename. #loglocation = '/var/log/dansguardian/access.log' # Network Settings # # the IP that DansGuardian listens on. If left blank DansGuardian will # listen on all IPs. That would include all NICs, loopback, modem, etc. # Normally you would have your firewall protecting this, but if you want # you can limit it to only 1 IP. Yes only one. filterip = # the port that DansGuardian listens to. filterport = 8080 # the ip of the proxy (default is the loopback - i.e. this server) proxyip = 127.0.0.1 # the port DansGuardian connects to proxy on proxyport = 3128 # accessdeniedaddress is the address of your web server to which the cgi # dansguardian reporting script was copied # Do NOT change from the default if you are not using the cgi. # accessdeniedaddress = 'http://YOURSERVER.YOURDOMAIN/cgi-bin/dansguardian.pl' # Non standard delimiter (only used with accessdeniedaddress) # Default is enabled but to go back to the original standard mode dissable it. nonstandarddelimiter = on # Banned image replacement # Images that are banned due to domain/url/etc reasons including those # in the adverts blacklists can be replaced by an image. This will, # for example, hide images from advert sites and remove broken image # icons from banned domains. # 0 = off # 1 = on (default) usecustombannedimage = 1 custombannedimagefile = '/etc/dansguardian/transparent1x1.gif' # Filter groups options # filtergroups sets the number of filter groups. A filter group is a set of content # filtering options you can apply to a group of users. The value must be 1 or more. # DansGuardian will automatically look for dansguardianfN.conf where N is the filter # group. To assign users to groups use the filtergroupslist option. All users default # to filter group 1. You must have some sort of authentication to be able to map users # to a group. The more filter groups the more copies of the lists will be in RAM so # use as few as possible. filtergroups = 1 filtergroupslist = '/etc/dansguardian/filtergroupslist' # Authentication files location bannediplist = '/etc/dansguardian/bannediplist' exceptioniplist = '/etc/dansguardian/exceptioniplist' banneduserlist = '/etc/dansguardian/banneduserlist' exceptionuserlist = '/etc/dansguardian/exceptionuserlist' # Show weighted phrases found # If enabled then the phrases found that made up the total which excedes # the naughtyness limit will be logged and, if the reporting level is # high enough, reported. on | off showweightedfound = on # Weighted phrase mode # There are 3 possible modes of operation: # 0 = off = do not use the weighted phrase feature. # 1 = on, normal = normal weighted phrase operation. # 2 = on, singular = each weighted phrase found only counts once on a page. # weightedphrasemode = 2 # Positive result caching for text URLs # Caches good pages so they don't need to be scanned again # 0 = off (recommended for ISPs with users with disimilar browsing) # 1000 = recommended for most users # 5000 = suggested max upper limit urlcachenumber = # # Age before they are stale and should be ignored in seconds # 0 = never # 900 = recommended = 15 mins urlcacheage = # Smart and Raw phrase content filtering options # Smart is where the multiple spaces and HTML are removed before phrase filtering # Raw is where the raw HTML including meta tags are phrase filtered # CPU usage can be effectively halved by using setting 0 or 1 # 0 = raw only # 1 = smart only # 2 = both (default) phrasefiltermode = 2 # Lower casing options # When a document is scanned the uppercase letters are converted to lower case # in order to compare them with the phrases. However this can break Big5 and # other 16-bit texts. If needed preserve the case. As of version 2.7.0 accented # characters are supported. # 0 = force lower case (default) # 1 = do not change case preservecase = 0 # Hex decoding options # When a document is scanned it can optionally convert %XX to chars. # If you find documents are getting past the phrase filtering due to encoding # then enable. However this can break Big5 and other 16-bit texts. # 0 = disabled (default) # 1 = enabled hexdecodecontent = 0 # Force Quick Search rather than DFA search algorithm # The current DFA implementation is not totally 16-bit character compatible # but is used by default as it handles large phrase lists much faster. # If you wish to use a large number of 16-bit character phrases then # enable this option. # 0 = off (default) # 1 = on (Big5 compatible) forcequicksearch = 0 # Reverse lookups for banned site and URLs. # If set to on, DansGuardian will look up the forward DNS for an IP URL # address and search for both in the banned site and URL lists. This would # prevent a user from simply entering the IP for a banned address. # It will reduce searching speed somewhat so unless you have a local caching # DNS server, leave it off and use the Blanket IP Block option in the # bannedsitelist file instead. reverseaddresslookups = off # Reverse lookups for banned and exception IP lists. # If set to on, DansGuardian will look up the forward DNS for the IP # of the connecting computer. This means you can put in hostnames in # the exceptioniplist and bannediplist. # It will reduce searching speed somewhat so unless you have a local DNS server, # leave it off. reverseclientiplookups = off # Build bannedsitelist and bannedurllist cache files. # This will compare the date stamp of the list file with the date stamp of # the cache file and will recreate as needed. # If a bsl or bul .processed file exists, then that will be used instead. # It will increase process start speed by 300%. On slow computers this will # be significant. Fast computers do not need this option. on | off createlistcachefiles = on # POST protection (web upload and forms) # does not block forms without any file upload, i.e. this is just for # blocking or limiting uploads # measured in kibibytes after MIME encoding and header bumph # use 0 for a complete block # use higher (e.g. 512 = 512Kbytes) for limiting # use -1 for no blocking #maxuploadsize = 512 #maxuploadsize = 0 maxuploadsize = -1 # Max content filter page size # Sometimes web servers label binary files as text which can be very # large which causes a huge drain on memory and cpu resources. # To counter this, you can limit the size of the document to be # filtered and get it to just pass it straight through. # This setting also applies to content regular expression modification. # The size is in Kibibytes - eg 2048 = 2Mb # use 0 for no limit maxcontentfiltersize = # Username identification methods (used in logging) # You can have as many methods as you want and not just one. The first one # will be used then if no username is found, the next will be used. # * proxyauth is for when basic proxy authentication is used (no good for # transparent proxying). # * ntlm is for when the proxy supports the MS NTLM authentication # protocol. (Only works with IE5.5 sp1 and later). **NOT IMPLEMENTED** # * ident is for when the others don't work. It will contact the computer # that the connection came from and try to connect to an identd server # and query it for the user owner of the connection. usernameidmethodproxyauth = on usernameidmethodntlm = off # **NOT IMPLEMENTED** usernameidmethodident = off # Preemptive banning - this means that if you have proxy auth enabled and a user accesses # a site banned by URL for example they will be denied straight away without a request # for their user and pass. This has the effect of requiring the user to visit a clean # site first before it knows who they are and thus maybe an admin user. # This is how DansGuardian has always worked but in some situations it is less than # ideal. So you can optionally disable it. Default is on. # As a side effect disabling this makes AD image replacement work better as the mime # type is know. preemptivebanning = on # Misc settings # if on it adds an X-Forwarded-For: <clientip> to the HTTP request # header. This may help solve some problem sites that need to know the # source ip. on | off forwardedfor = on # if on it uses the X-Forwarded-For: <clientip> to determine the client # IP. This is for when you have squid between the clients and DansGuardian. # Warning - headers are easily spoofed. on | off usexforwardedfor = off # if on it logs some debug info regarding fork()ing and accept()ing which # can usually be ignored. These are logged by syslog. It is safe to leave # it on or off logconnectionhandlingerrors = on # Fork pool options # sets the maximum number of processes to sporn to handle the incomming # connections. Max value usually 250 depending on OS. # On large sites you might want to try 180. maxchildren = 180 # sets the minimum number of processes to sporn to handle the incomming connections. # On large sites you might want to try 32. minchildren = 32 # sets the minimum number of processes to be kept ready to handle connections. # On large sites you might want to try 8. minsparechildren = 8 # sets the minimum number of processes to sporn when it runs out # On large sites you might want to try 10. preforkchildren = 10 # sets the maximum number of processes to have doing nothing. # When this many are spare it will cull some of them. # On large sites you might want to try 64. maxsparechildren = 64 # sets the maximum age of a child process before it croaks it. # This is the number of connections they handle before exiting. # On large sites you might want to try 10000. maxagechildren = 5000 # Process options # (Change these only if you really know what you are doing). # These options allow you to run multiple instances of DansGuardian on a single machine. # Remember to edit the log file path above also if that is your intention. # IPC filename # # Defines IPC server directory and filename used to communicate with the log process. ipcfilename = '/tmp/.dguardianipc' # URL list IPC filename # # Defines URL list IPC server directory and filename used to communicate with the URL # cache process. urlipcfilename = '/tmp/.dguardianurlipc' # PID filename # # Defines process id directory and filename. #pidfilename = '/var/run/dansguardian.pid' # Disable daemoning # If enabled the process will not fork into the background. # It is not usually advantageous to do this. # on|off ( defaults to off ) nodaemon = off # Disable logging process # on|off ( defaults to off ) nologger = off # Daemon runas user and group # This is the user that DansGuardian runs as. Normally the user/group nobody. # Uncomment to use. Defaults to the user set at compile time. # daemonuser = 'nobody' # daemongroup = 'nobody' # Soft restart # When on this disables the forced killing off all processes in the process group. # This is not to be confused with the -g run time option - they are not related. # on|off ( defaults to off ) softrestart = off maxcontentramcachescansize = 2000 maxcontentfilecachescansize = 20000 downloadmanager = '/etc/dansguardian/downloadmanagers/default.conf' authplugin = '/etc/dansguardian/authplugins/proxy-basic.conf' Squid.conf http_port 3128 hierarchy_stoplist cgi-bin ? acl QUERY urlpath_regex cgi-bin \? cache deny QUERY acl apache rep_header Server ^Apache #broken_vary_encoding allow apache access_log /squid/var/logs/access.log squid hosts_file /etc/hosts auth_param basic program /squid/libexec/ncsa_auth /squid/etc/userbasic.auth auth_param basic children 5 auth_param basic realm proxy auth_param basic credentialsttl 2 hours auth_param basic casesensitive off refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern . 0 20% 4320 acl NoAuthNec src <HIDDEN FOR SECURITY> acl BrkRm src <HIDDEN FOR SECURITY> acl Dials src <HIDDEN FOR SECURITY> acl Comps src <HIDDEN FOR SECURITY> acl whsws dstdom_regex -i .opensuse.org .novell.com .suse.com mirror.mcs.an1.gov mirrors.kernerl.org www.suse.de suse.mirrors.tds.net mirrros.usc.edu ftp.ale.org suse.cs.utah.edu mirrors.usc.edu mirror.usc.an1.gov linux.nssl.noaa.gov noaa.gov .kernel.org ftp.ale.org ftp.gwdg.de .medibuntu.org mirrors.xmission.com .canonical.com .ubuntu. acl opensites dstdom_regex -i .mbsbooks.com .bowker.com .usps.com .usps.gov .ups.com .fedex.com go.microsoft.com .microsoft.com .apple.com toolbar.msn.com .contacts.msn.com update.services.openoffice.org fms2.pointroll.speedera.net services.wmdrm.windowsmedia.com windowsupdate.com .adobe.com .symantec.com .vitalbook.com vxn1.datawire.net vxn.datawire.net download.lavasoft.de .download.lavasoft.com .lavasoft.com updates.ls-servers.com .canadapost. .myyellow.com minirick symantecliveupdate.com wm.overdrive.com www.overdrive.com productactivation.one.microsoft.com www.update.microsoft.com testdrive.whoson.com www.columbia.k12.mo.us banners.wunderground.com .kofax.com .gotomeeting.com tools.google.com .dl.google.com .cache.googlevideo.com .gpdl.google.com .clients.google.com cache.pack.google.com kh.google.com maps.google.com auth.keyhole.com .contacts.msn.com .hrblock.com .taxcut.com .merchantadvantage.com .jtv.com .malwarebytes.org www.google-analytics.com dcs.support.xerox.com .dhl.com .webtrendslive.com javadl-esd.sun.com javadl-alt.sun.com .excelsior.edu .dhlglobalmail.com .nessus.org .foxitsoftware.com foxit.vo.llnwd.net installshield.com .mindjet.com .mediascouter.com media.us.elsevierhealth.com .xplana.com .govtrack.us sa.tulsacc.edu .omniture.com fpdownload.macromedia.com webservices.amazon.com acl password proxy_auth REQUIRED acl all src all acl manager proto cache_object acl localhost src 127.0.0.1/255.255.255.255 acl to_localhost dst 127.0.0.0/8 acl SSL_ports port 443 563 631 2001 2005 8731 9001 9080 10000 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port # https, snews 443 563 acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port # unregistered ports 1936-65535 acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 10000 acl Safe_ports port 631 acl Safe_ports port 901 # SWAT acl purge method PURGE acl CONNECT method CONNECT acl UTubeUsers proxy_auth "/squid/etc/utubeusers.list" acl RestrictUTube dstdom_regex -i youtube.com acl RestrictFacebook dstdom_regex -i facebook.com acl FacebookUsers proxy_auth "/squid/etc/facebookusers.list" acl BuemerKEC src 10.10.128.0/24 acl MBSsortnet src 10.10.128.0/26 acl MSNExplorer browser -i MSN acl Printers src <HIDDEN FOR SECURITY> acl SpecialFolks src <HIDDEN FOR SECURITY> # streaming download acl fails rep_mime_type ^.*mms.* acl fails rep_mime_type ^.*ms-hdr.* acl fails rep_mime_type ^.*x-fcs.* acl fails rep_mime_type ^.*x-ms-asf.* acl fails2 urlpath_regex dvrplayer mediastream mms:// acl fails2 urlpath_regex \.asf$ \.afx$ \.flv$ \.swf$ acl deny_rep_mime_flashvideo rep_mime_type -i video/flv acl deny_rep_mime_shockwave rep_mime_type -i ^application/x-shockwave-flash$ acl x-type req_mime_type -i ^application/octet-stream$ acl x-type req_mime_type -i application/octet-stream acl x-type req_mime_type -i ^application/x-mplayer2$ acl x-type req_mime_type -i application/x-mplayer2 acl x-type req_mime_type -i ^application/x-oleobject$ acl x-type req_mime_type -i application/x-oleobject acl x-type req_mime_type -i application/x-pncmd acl x-type req_mime_type -i ^video/x-ms-asf$ acl x-type2 rep_mime_type -i ^application/octet-stream$ acl x-type2 rep_mime_type -i application/octet-stream acl x-type2 rep_mime_type -i ^application/x-mplayer2$ acl x-type2 rep_mime_type -i application/x-mplayer2 acl x-type2 rep_mime_type -i ^application/x-oleobject$ acl x-type2 rep_mime_type -i application/x-oleobject acl x-type2 rep_mime_type -i application/x-pncmd acl x-type2 rep_mime_type -i ^video/x-ms-asf$ acl RestrictHulu dstdom_regex -i hulu.com acl broken dstdomain cms.montgomerycollege.edu events.columbiamochamber.com members.columbiamochamber.com public.genexusserver.com acl RestrictVimeo dstdom_regex -i vimeo.com acl http_port port 80 #http_reply_access deny deny_rep_mime_flashvideo #http_reply_access deny deny_rep_mime_shockwave #streaming files #http_access deny fails #http_reply_access deny fails #http_access deny fails2 #http_reply_access deny fails2 #http_access deny x-type #http_reply_access deny x-type #http_access deny x-type2 #http_reply_access deny x-type2 follow_x_forwarded_for allow localhost acl_uses_indirect_client on log_uses_indirect_client on http_access allow manager localhost http_access deny manager http_access allow purge localhost http_access deny purge http_access allow SpecialFolks http_access deny CONNECT !SSL_ports http_access allow whsws http_access allow opensites http_access deny BuemerKEC !MBSsortnet http_access deny BrkRm RestrictUTube RestrictFacebook RestrictVimeo http_access allow RestrictUTube UTubeUsers http_access deny RestrictUTube http_access allow RestrictFacebook FacebookUsers http_access deny RestrictFacebook http_access deny RestrictHulu http_access allow NoAuthNec http_access allow BrkRm http_access allow FacebookUsers RestrictVimeo http_access deny RestrictVimeo http_access allow Comps http_access allow Dials http_access allow Printers http_access allow password http_access deny !Safe_ports http_access deny SSL_ports !CONNECT http_access allow http_port http_access deny all http_reply_access allow all icp_access allow all access_log /squid/var/logs/access.log squid visible_hostname proxy.site.com forwarded_for off coredump_dir /squid/cache/ #header_access Accept-Encoding deny broken #acl snmppublic snmp_community mysecretcommunity #snmp_port 3401 #snmp_access allow snmppublic all cache_mem 3 GB #acl snmppublic snmp_community mbssquid #snmp_port 3401 #snmp_access allow snmppublic all

  Read the article

• Useful Command-line Commands on Windows

  - by Sung Meister

  The aim for this Wiki is to promote using a command to open up commonly used applications without having to go through many mouse clicks - thus saving time on monitoring and troubleshooting Windows machines. Answer entries need to specify Application name Commands Screenshot (Optional) Shortcut to commands && - Command Chaining %SYSTEMROOT%\System32\rcimlby.exe -LaunchRA - Remote Assistance (Windows XP) appwiz.cpl - Programs and Features (Formerly Known as "Add or Remove Programs") appwiz.cpl @,2 - Turn Windows Features On and Off (Add/Remove Windows Components pane) arp - Displays and modifies the IP-to-Physical address translation tables used by address resolution protocol (ARP) at - Schedule tasks either locally or remotely without using Scheduled Tasks bootsect.exe - Updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR cacls - Change Access Control List (ACL) permissions on a directory, its subcontents, or files calc - Calculator chkdsk - Check/Fix the disk surface for physical errors or bad sectors cipher - Displays or alters the encryption of directories [files] on NTFS partitions cleanmgr.exe - Disk Cleanup clip - Redirects output of command line tools to the Windows clipboard cls - clear the command line screen cmd /k - Run command with command extensions enabled color - Sets the default console foreground and background colors in console command.com - Default Operating System Shell compmgmt.msc - Computer Management control.exe /name Microsoft.NetworkAndSharingCenter - Network and Sharing Center control keyboard - Keyboard Properties control mouse(or main.cpl) - Mouse Properties control sysdm.cpl,@0,3 - Advanced Tab of the System Properties dialog control userpasswords2 - Opens the classic User Accounts dialog desk.cpl - opens the display properties devmgmt.msc - Device Manager diskmgmt.msc - Disk Management diskpart - Disk management from the command line dsa.msc - Opens active directory users and computers dsquery - Finds any objects in the directory according to criteria dxdiag - DirectX Diagnostic Tool eventvwr - Windows Event Log (Event Viewer) explorer . - Open explorer with the current folder selected. explorer /e, . - Open explorer, with folder tree, with current folder selected. F7 - View command history find - Searches for a text string in a file or files findstr - Find a string in a file firewall.cpl - Opens the Windows Firewall settings fsmgmt.msc - Shared Folders fsutil - Perform tasks related to FAT and NTFS file systems ftp - Transfers files to and from a computer running an FTP server service getmac - Shows the mac address(es) of your network adapter(s) gpedit.msc - Group Policy Editor gpresult - Displays the Resultant Set of Policy (RSoP) information for a target user and computer httpcfg.exe - HTTP Configuration Utility iisreset - To restart IIS InetMgr.exe - Internet Information Services (IIS) Manager 7 InetMgr6.exe - Internet Information Services (IIS) Manager 6 intl.cpl - Regional and Language Options ipconfig - Internet protocol configuration lusrmgr.msc - Local Users and Groups Administrator msconfig - System Configuration notepad - Notepad? ;) mmsys.cpl - Sound/Recording/Playback properties mode - Configure system devices more - Displays one screen of output at a time mrt - Microsoft Windows Malicious Software Removal Tool mstsc.exe - Remote Desktop Connection nbstat - displays protocol statistics and current TCP/IP connections using NBT ncpa.cpl - Network Connections netsh - Display or modify the network configuration of a computer that is currently running netstat - Network Statistics net statistics - Check computer up time net stop - Stops a running service. net use - Connects a computer to or disconnects a computer from a shared resource, or displays information about computer connections odbcad32.exe - ODBC Data Source Administrator pathping - A traceroute that collects detailed packet loss stats perfmon - Opens Reliability and Performance Monitor ping - Determine whether a remote computer is accessible over the network powercfg.cpl - Power management control panel applet quser - Display information about user sessions on a terminal server qwinsta - See disconnected remote desktop sessions reg.exe - Console Registry Tool for Windows regedit - Registry Editor rasdial - Connects to a VPN or a dialup network robocopy - Backup/Restore/Copy large amounts of files reliably rsop.msc - Resultant Set of Policy (shows the combined effect of all group policies active on the current system/login) runas - Run specific tools and programs with different permissions than the user's current logon provides sc - Manage anything you want to do with services. schtasks - Enables an administrator to create, delete, query, change, run and end scheduled tasks on a local or remote system. secpol.msc - Local Security Settings services.msc - Services control panel set - Displays, sets, or removes cmd.exe environment variables. set DIRCMD - Preset dir parameter in cmd.exe start - Starts a separate window to run a specified program or command start. - opens the current directory in the Windows Explorer. shutdown.exe - Shutdown or Reboot a local/remote machine subst.exe - Associates a path with a drive letter, including local drives systeminfo -Displays a comprehensive information about the system taskkill - terminate tasks by process id (PID) or image name tasklist.exe - List Processes on local or a remote machine taskmgr.exe - Task Manager telephon.cpl - Telephone and Modem properties timedate.cpl - Date and Time title - Change the title of the CMD window you have open tracert - Trace route wmic - Windows Management Instrumentation Command-line winver.exe - Find Windows Version wscui.cpl - Windows Security Center wuauclt.exe - Windows Update AutoUpdate Client

  Read the article

• ubuntu 10.04; kvm bridged networking not working with public ip addresses

  - by senorsmile

  I have a dedicated hosted server box with ubuntu 10.04 64 bit installed. I would like to run kvm with ubuntu 8.04 installed for some php 5.2 compatible apps(they don't work right with php 5.3, the default in ubuntu 10.04). I installed KVM as instructed at https://help.ubuntu.com/community/KVM/Installation . I installed the vm using virt-manager. I never could figure out how use virt-install or any of those automated installers. I just installed it using the disc. I set up bridged networking as per https://help.ubuntu.com/community/KVM/Networking . However, the bridged connection doesn't work. Here's my /etc/network/interfaces on the host, running ubuntu 10.04. (with specific public ip blanked) auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address xx.xx.xx.xx netmask 255.255.255.248 gateway xx.xx.xx.xa bridge_ports eth0 bridge_stp on bridge_fd 0 bridge_maxwait 10 ` Here's my /etc/network/interfaces on the guest, running ubuntu 8.04. auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xy netmask 255.255.255.248 gateway xx.xx.xx.xa The two vm's can communicate to each other. But, the guest vm can't access anyone in the real world. Here's my /etc/libvirt/qemu/store_804.xml <domain type='kvm'> <name>store_804</name> <uuid>27acfb75-4f90-a34c-9a0b-70a6927ae84c</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/store_804.img'/> <target dev='hda' bus='ide'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> </disk> <interface type='bridge'> <mac address='52:54:00:26:0b:c6'/> <source bridge='br0'/> <model type='virtio'/> </interface> <console type='pty'> <target port='0'/> </console> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='es1370'/> <video> <model type='cirrus' vram='9216' heads='1'/> </video> </devices> </domain> Any idea where I've gone wrong?

  Read the article

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• What *exactly* gets screwed when I kill -9 or pull the power?

  - by Mike

  Set-Up I've been a programmer for quite some time now but I'm still a bit fuzzy on deep, internal stuff. Now. I am well aware that it's not a good idea to either: kill -9 a process (bad) spontaneously pull the power plug on a running computer or server (worse) However, sometimes you just plain have to. Sometimes a process just won't respond no matter what you do, and sometimes a computer just won't respond, no matter what you do. Let's assume a system running Apache 2, MySQL 5, PHP 5, and Python 2.6.5 through mod_wsgi. Note: I'm most interested about Mac OS X here, but an answer that pertains to any UNIX system would help me out. My Concern Each time I have to do either one of these, especially the second, I'm very worried for a period of time that something has been broken. Some file somewhere could be corrupt -- who knows which file? There are over 1,000,000 files on the computer. I'm often using OS X, so I'll run a "Verify Disk" operation through the Disk Utility. It will report no problems, but I'm still concerned about this. What if some configuration file somewhere got screwed up. Or even worse, what if a binary file somewhere is corrupt. Or a script file somewhere is corrupt now. What if some hardware is damaged? What if I don't find out about it until next month, in a critical scenario, when the corruption or damage causes a catastrophe? Or, what if valuable data is already lost? My Hope My hope is that these concerns and worries are unfounded. After all, after doing this many times before, nothing truly bad has happened yet. The worst is I've had to repair some MySQL tables, but I don't seem to have lost any data. But, if my worries are not unfounded, and real damage could happen in either situation 1 or 2, then my hope is that there is a way to detect it and prevent against it. My Question(s) Could this be because modern operating systems are designed to ensure that nothing is lost in these scenarios? Could this be because modern software is designed to ensure that nothing lost? What about modern hardware design? What measures are in place when you pull the power plug? My question is, for both of these scenarios, what exactly can go wrong, and what steps should be taken to fix it? I'm under the impression that one thing that can go wrong is some programs might not have flushed their data to the disk, so any highly recent data that was supposed to be written to the disk (say, a few seconds before the power pull) might be lost. But what about beyond that? And can this very issue of 5-second data loss screw up a system? What about corruption of random files hiding somewhere in the huge forest of files on my hard drives? What about hardware damage? What Would Help Me Most Detailed descriptions about what goes on internally when you either kill -9 a process or pull the power on the whole system. (it seems instant, but can someone slow it down for me?) Explanations of all things that could go wrong in these scenarios, along with (rough of course) probabilities (i.e., this is very unlikely, but this is likely)... Descriptions of measures in place in modern hardware, operating systems, and software, to prevent damage or corruption when these scenarios occur. (to comfort me) Instructions for what to do after a kill -9 or a power pull, beyond "verifying the disk", in order to truly make sure nothing is corrupt or damaged somewhere on the drive. Measures that can be taken to fortify a computer setup so that if something has to be killed or the power has to be pulled, any potential damage is mitigated. Thanks so much!

  Read the article

• Required Skill Sets Of A Software Architect

  The question has been asked as to what is the required skill sets of a software architect. The answer to this is that it truly depends. When I state that it depend, it depends on the organization, industry, and skill sets available on the open market and internally within a company. With open ended skill sets even Napoleon Dynamite could be an architect. Napoleon Dynamite’s Skills Pedro: Have you asked anybody yet? Napoleon Dynamite: No, but who would? I don't even have any good skills. Pedro: What do you mean? Napoleon Dynamite: You know, like nunchuck skills, bow hunting skills, computer hacking skills... Girls only want boyfriends who have great skills. Pedro: Aren't you pretty good at drawing, like animals and warriors and stuff? This example might be a little off base but it does illustrate a point. What are the real required skills of a software architect? In my opinion, an architect needs to demonstrate the knowledge of the following three main skill set categories so that they are successful. General Skill Sets of an Architect Basic Engineering Skills Organizational  Skills Interpersonal Skills Basic Engineering Skills are a very large part of what a software architect deal with on a daily bases when designing or updating systems. Think about it, how good would a lead mechanic be if they did not know how to fix or repair cars? They would not be, and that is my point that architects need to have at least some basic skills regarding engineering. The skills listed below are generic in nature because they change from job to job, so in this discussion I am trying to focus more on generalities so that anyone can apply this information to their individual situation. Common Basic Engineering Skills Data Modeling Code Creation Configuration Testing Deployment/Publishing System and Environment Knowledge Organizational Skills If an Architect works for or with an origination then they will need strong organization skills to survive. An architect is no use to a project if the project is missed managed. Additionally, budgets and timelines can really affect a company and their products when established deadlines are repeated not meet. By not meeting these timelines a company is forced to cancel the project and waste all the money and time spent or spend more money until it is completed, if it is ever completed. Common Organizational Skills Project Management Estimation (Cost and Time) Creation and Maintenance of Accepted Standards Interpersonal Skills For me personally Interpersonal skill ranks above the other types of skill sets because an architect can quickly pick up the other two skill sets by communicating with other team/project members so that they are quickly up to speed on a project. Additionally, in order for an architect to manage a project or even derive rough estimates they will more than likely have to consult with others actually working on the code (Programmers/Software Engineers) to get there estimates since they will be the ones actually working on the changes to be implemented. Common Interpersonal Skills Good Communicator Focus on projects success over personal Honors roles within a team Reference: Taylor, R. N., Medvidovic, N., & Dashofy, E. M. (2009). Software architecture: Foundations, theory, and practice Hoboken, NJ: John Wiley & Sons

  Read the article

• Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

  - by Ryan Rosario

  I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

  Read the article

• Converting an Oracle VM VirtualBox VM into an Oracle VM Server image

  - by wim.coekaerts

  As we are working on tighter seemless moving of VM's between the 2 products, here are a few simple steps to convert an existing Oracle VM VirtualBox image over. Steps involved to make it easy/straightforward : (1) When creating a VM in Virtualbox, using Oracle Linux as an example, make sure that /etc/fstab only uses labels. Do not use hardcoded device names. instead of an entry /dev/sda1 /u01 ext3 defaults 1 1 use LABEL=foo /u01 ext3 defaults 1 1 for more info on labels : man e2label or use a logical volume /dev/VolGroup00/LVfoo /u01 ext3 defaults 1 1 Doing so will make it easier to have an OS boot up on a different hypervisor with potentially different device names. For instance, the VirtualBox VM might expose a scsi driver while in Oracle VM Server you might end up with an ide disk, this then changes /dev/sda to /dev/hda. (2) If you have a VM created that you want to convert, then shut down the VM in VirtualBox and convert the image files : go the the directory that contains your HardDisk image files (.VirtualBox/HardDisks/* as an example) for each of the virtual disks run the following command : VBoxManage clonehd virtualdiskfilename.vdi system.img --format raw where virtualdiskfilename.vdi is the original VBox VM file (this can also be a vmdk file) and system.img is the name of the virtualdisk for Oracle VM. this can be any filename as well, I typically use system.img to specify the boot disk (as is common for Oracle VM template creation) (3) create a vm.cfg To run a VM converted from VirtualBox, you have to create a vm.cfg for Oracle VM server that creates an HVM guest. The easiest is to use a simple hvm vm.cfg and change it for your vm. I have an example here : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' disk = ['file:system.img,hda,w', 'file:oracle.img,hdb,w',',hdc:cdrom,r',] kernel = '/usr/lib/xen/boot/hvmloader' memory = '1024' name = 'vmname' on_crash = 'restart' on_reboot = 'restart' pae = 1 serial = 'pty' timer_mode = '0' usbdevice = 'tablet' vcpus = 1 vif = ['bridge=xenbr0,type=ioemu'] vif_other_config = [] vnc = 1 vncconsole = 1 vnclisten = '0.0.0.0' vncpasswd = '' vncunused = 1 If you take the above vm.cfg, all you need to do - modify disk = (add your virtual disks in there) - modify memory = (amount of memory your VM needs) - modify name = (enter a name for your VM here) - modify vif = (might want to replace bridge=xenbr0 to the bridge you want to use) if you want more than 1 vcpu or other changes of course you have to make those as well. (4) copy this set of files onto your Oracle VM server or onto a webserver in a subdirectory and import the template through Oracle VM Manager. You can also just start the vm using xm create vm.cfg if you like. And that's it. As I said, we are working on automation around all this but it is relatively trivial to convert VM's over as long as you take the basic issues into account. Primarily the set up of the filesystems and the use of labels in /etc/fstab. There are other potential things to look at, such as network config. If you want to make that part clean then prior to shutting down the VM change /etc/modprobe.conf and/or add the mac address of the VM into the vm.cfg in the vifs line. The good thing, at least with Linux, is that even tho the virtual hardware changes, Linux will deal with it just fine (e1000 vs 8139 realtek, ide vs scsi etc). hope this helps.

  Read the article

• F# WPF Form &ndash; the basics

  - by MarkPearl

  I was listening to Dot Net Rocks show #560 about F# and during the podcast Richard Campbell brought up a good point with regards to F# and a GUI. In essence what I understood his point to be was that until one could write an end to end application in F#, it would be a hard sell to developers to take it on. In part I agree with him, while I am beginning to really enjoy learning F#, I can’t but help feel that I would be a lot further into the language if I could do my Windows Forms like I do in C# or VB.NET for the simple reason that in “playing” applications I spend the majority of the time in the UI layer… So I have been keeping my eye out for some examples of creating a WPF form in a F# project and came across Tim’s F# Twitter Stream Sample, which had exactly this…. of course he actually had a bit more than a basic form… but it was enough for me to scrap the insides and glean what I needed. So today I am going to make just the very basic WPF form with all the goodness of a XAML window. Getting Started First thing we need to do is create a new solution with a blank F# application project – I have made mine called FSharpWPF. Once you have the project created you will need to change the project type from a Console Application to a Windows Application. You do this by right clicking on the project file and going to its properties… Once that is done you will need to add the appropriate references. You do this by right clicking on the References in the Solution Explorer and clicking “Add Reference'”. You should add the appropriate .Net references below for WPF & XAMl to work. Once these references are added you then need to add your XAML file to the project. You can do this by adding a new item to the project of type xml and simply changing the file extension from xml to xaml. Once the xaml file has been added to the project you will need to add valid window XAML. Example of a very basic xaml file is shown below… <Window xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="F# WPF WPF Form" Height="350" Width="525"> <Grid> </Grid> </Window> Once your xaml file is done… you need to set the build action of the xaml file from “None” to “Resource” as depicted in the picture below. If you do not set this you will get an IOException error when running the completed project with a message along the lines of “Cannot locate resource ‘window.xaml’ You then need to tie everything up by putting the correct F# code in the Program.fs to load the xaml window. In the Program.fs put the following code… module Program open System open System.Collections.ObjectModel open System.IO open System.Windows open System.Windows.Controls open System.Windows.Markup [<STAThread>] [<EntryPoint>] let main(_) = let w = Application.LoadComponent(new System.Uri("/FSharpWPF;component/Window.xaml", System.UriKind.Relative)) :?> Window (new Application()).Run(w) Once all this is done you should be able to build and run your project. What you have done is created a WPF based window inside a FSharp project. It should look something like below…   Nothing to exciting, but sufficient to illustrate the very basic WPF form in F#. Hopefully in future posts I will build on this to expose button events etc.

  Read the article

< Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >