Search Results

Search found 4440 results on 178 pages for 'intel atom'.

Page 159/178 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• Hearing a clicking noise from soundcard all the time

  - by Mehrdad

  I have installed Fedora 17 on my laptop. A few days ago I updated my fedora (but not upgraded). I shut down my computer and since the next time I turned it on I am hearing a clicking noise all the time from speakers. Even when I plug my headphones in I hear the noise through the headphone. I surfed over the internet and found the following shell commands: su -c 'echo "options snd_hda_intel power_save=0" /etc/modprobe.d/snd_hda_intel.conf' su -c 'echo 0 /sys/module/snd_hda_intel/parameters/power_save' I tried them but they didn't work. Here is the part of "lspci" command related to my sound-card: 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) I have to add that my sound-card is working and I can play some audio file, I mean I can hear the voice and noise simultaneously. But everything is OK in windows xp which is also installed on my laptop. Could it be related to the sound-card driver? If so, how can I revert it to the previous version?

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• (Win7) Gets stuck with ~1% CPU. Especially with multithreading

  - by meow

  Windows 7 32 bit, up to date, Intel i7 860. (For some reason the company runs 32bit Windows everywhere.) I tried to update all motherboard drivers etc. as far as possible. I have a performance issue with a machine which appears in connection with multithreading (or so I think). As an example (and where I most often see it, but it appears on other programs as well): ProteoWizard is a file conversion tool for mass spectrometry files. I can add a list of files and it will attempt to process up to 8 files in parallel (quadcore x 2 threads/core). If I choose 1 to 6 files, I start the process and it goes straight through. If I have =7 files in the queue, conversion goes to ~20%, then gets stuck for 15 seconds, then continues again, always in "chunks" of a few % before getting stuck again. During the time the process is stuck, CPU is at 1%. RAM is not limiting, it is maybe at 70% or so and not going up. I don't get the same problem on other, even slower machines. The computer gets also stuck at 1% CPU doing nothing on other occasions, but for multithreading it is most frequent. Where should I look for the problem?

  Read the article

• How should I configure backup of my server?

  - by ed209

  I have just rented a dedicated server. If it helps this is the config I have: CPU1 Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz (Cores 8) RAM 15975 MB Disk /dev/sda doesn't contain a valid partition table (=> /dev/sda doesn't) Disk /dev/sdc doesn't contain a valid partition table (=> /dev/sdc doesn't) Disk /dev/sdb doesn't contain a valid partition table (=> /dev/sdb doesn't) Disk /dev/sda: 120.0 GB (=> 114 GIB) Disk /dev/sdc: 3000.6 GB (=> 2861 GIB) Disk /dev/sdb: 3000.6 GB (=> 2861 GIB) /dev/sda is a 120GB SSD. This is where I have Ubuntu/lamp installed. It's the drive that will run my site. With the account I got two other drives of 3000GB each which I really don't need but they came with the account. I figured I could use these to back up my main 120gb drive. So a couple of things I wondered were: Should I use these for backups? How should I back up. The data I want to back up is a user uploads directory full of images and the database. Everything else is either in a code repo or backed up some other way. For example, it would be nice to know there is a disk image of the 120gb drive somewhere that I can copy over should there be any problems but equally I don't mind doing a fresh install of all the software and copying over just the images and database dump. Thanks for your advice! (also, happy to not use the two other drives and backup elsewhere if it's more sensible)

  Read the article

• What's throttling the database?

  - by Troels Arvin

  Hardware: Intel x86_64 with 192GB of RAM. OS: CentOS 5.4 x86_64. DBMS: DB2 v. 9.7.1 64 bit. During certain special workloads (e.g. parallel REORGs/RUNSTATs), I've seen the server transporting 450MB/s with 25000IO/s (yes, there is probably some storage system caching happening here) while all CPU cores were happily working in an even mix of usermode/wait. And disk benchmark tools can also bring some very satisfying bandwith and IO/s numbers to the table. On the other hand, we also have another scenario: A single rather complex query with at least one large table scan. db2's "list applications" reports that the query is Executing (not locked). IO: At most 10MB/s, 500 IO/s; CPU: two cores in 99.9% wait state, all other cores 100% idle. The tables which the query reads from have been altered to have LOCKSIZE=TABLE, so I would think that lock list work is zero. What's going on in such a situation? What tools/snapshots/... can I use to gain better insight in such a case?

  Read the article

• Windows won't boot after moving house. How do I solve this?

  - by James

  Ive just moved house and tried to set up my desktop after packing it away and now when I power it on, the BIOS boots up and no errors are found but when my computer tires to boot into Windows 7 a continuous fast beeping sound is made and a black screen is displayed. What I've done so far: Reset to UEFI defauts Played about with RAM, I had 4*4 GB sticks, I took all of them out to test for a mobo error which I have and now im only using 1 stick of 4 GB. Changed my GPU, I tok my gtx580 out and now im using the onboard Intel 3000 graphics driver, the BIOS and uefi are correctly displaying so I no longer think its a GPU based error. Ive check all of the connections and nothing seems to be loose. My HDD setup is: 2 128 GB SSD's in Raid 0 as my main C drive (possibly cause of error?) 1 1 TB Games drive 1 2 TB Data Drive Ive also got a blueray drive connected. After searching the internet im pretty much out of suggestions but im currently downloading a live CD to see if it will boot and if I can access some files on my HDD.

  Read the article

• How to improve Samba performance on VirtualBox machine?

  - by ColinM

  I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

  Read the article

• Adjust output Brightness/Gamma/Colors in Gnome

  - by Mikee

  We have a desktop system running Ubuntu 8.04.4, and it is connected to a standard desktop LCD monitor. Unfortunately, in 8.04.4, the brightness of the image is cranked way up. It appears to be a graphics driver issue. Unfortunately, installing a newer GPU driver for this Intel GPU is very difficult to do. So, I am looking for a software (or config file?) solution to achieve this. Note: Ubuntu 9.10 and higher do not exhibit this issue, so this is not a hardware problem. Note: VNC-ing to this machine from another does not exhibit this issue either. Also, I installed "DisplayCalibrator.app", and it does not work very well (the app comes up, but the contents of the window are blank). Is there anything that I can add to the xorg.conf file to correct this issue? Also, this solution: http://superuser.com/questions/96539/adjust-contrast-and-brightness-in-ubuntu did not resove my issue. Thank you all for the help!

  Read the article

• My new SSD is causing issues. How can I solve them?

  - by Allan

  Computer specs 1 TB harddisc 120 GB 520intel SSD 8 GB DDR3 RAM Athlon Phenom II x64 955 3. 2ghz DK DFI Lanparty FX7900 M3H3 motherboard ASUS ATI RADEON HD6970 2 GB I have bought a new SSD (Intel 520, 120 GB), and wanted to use this as my system disc. I removed the other harddisc, and installed the SSD with the newest firmware. And then Windows 7 I updated Windows 7 with no problems and then put back my old harddrive. I formatted that old harddrive just to clean up at the same time... So at this stage everything was perfect. My new SSD was set as Master 0 Primary it boots on it and I have 1 TB emptyu harddrive I can use for whatever I want. So far no errors at all Now here is the problem, I installed a few games and everytime I tried to play the computer would say Windows must restart because DCOM server process launcher service terminated, or it says Windows must now restart because the Plug and Play service terminated unexpectedly Most commonly this error is caused by a rootkit virus, well I have tried formatting my entire computer, and running every antivirus I could find, so that shouldn't be it. I've also read somewhere it might happen when there are hardware issues. That on the otherhand would make sense, as I just put in a new SSD. I don't expect you to know this error. I haven't found anyone who knew it yet. maybe you can me guide through what might have gone wrong when I placed in the SSD? What have I checked regarding the SSD? It displays the right name when the computer starts up It has the newest firmware Did a 'sfc /scannow' which told me everything was fine I don't know what to do from here. Everything seems to work great with the drive. when I start playing games my computer crashes.

  Read the article

• SQL Server 2005 SE SP3 on Windows Server 2008 R2 x64 premature query disconnections

  - by southernpost

  New Dell PowerEdge R910, 4x8 Intel X7560, 192GB RAM, hardware NUMA, local RAID, Broadcom NetExtreme II multiport NIC, unteamed, TCP Offload disabled, RSS disabled, NetDMA disabled, Hyperthreading disabled. SQL Server 2005 SE x64 SP3 on Windows Server 2008 R2 EE x64. No other apps on server. Max Mem = 180GB, Max DOP = 4. Existing Windows Server 2003 R2 EE x64 app server connecting to Dell via firewall using SQL Authenticated logins. Symptoms: Intermittent errors at the app server: A transport-level error has occurred when sending the request to the server. (provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) Findings: Running queries from SSMS located on another machine within the same domain as the SQL Server run without error. SQLIO showed good performance. Windows and SQL logs show no related messages. Microsoft reveiwed PssDiag trace and stated that "We are not seeing timeouts from SQL Side. The queries bring run against the database are timing out within 9secs. This is a database connectivity error." "we can also see from the AttnSeq column that we are also not seeing any Attentions from the SQL Side.". Dell has confirmed that we are using the latest Broadcom drivers.

  Read the article

• Path Environmental Variable errors

  - by roymustang86

  So, I am trying to learn java. I installed the JDK and proceeded to write a few programs. Each time, I have to give the path to javac.exe to compile the .java file. SO, I decided to tweak the %PATH% variable. And no matter what I change it to, it doesn't work. when I do an echo %PATH%, I get 'Program' is not recognized as an internal or external command, operable program or batch file. This is my Path variable contents : C:\app\product\11.1.0\client_1\bin;%CommonProgramFiles%\Microsoft Shared\Windows Live;%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;"C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\";"C:\Program Files\Broadcom\Broadcom 802.11";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\12.0\DLLShared\";"C:\Program Files (x86)\Roxio\OEM\AudioCore\";"C:\Program Files (x86)\Intel\Services\IPT\" How do I work around this? the double quotes were not there before, I added it thinking the space was the problem.

  Read the article

• Hyper-V and attaching physical disks

  - by Mike Christiansen

  So, I'm looking at rebuilding my home server. My current setup is the following Windows 7 Ultimate 1TB Boot Drive (my smallest drive) Windows Dynamic Spanned volume, continaing 1x 1TB drive, 2x 2TB drives, totalling 5TB. I am upgrading to a hardware RAID controller, and I would like to run Hyper-V server core. However, I want to retain the ability to join my "file server" to a homegroup, so I must use Windows 7. I know VHDs can only be like 127GB or something, so I obviously need to directly connect disks to my Windows 7 machine. Here is my plan: Server Core 2008 R2 (Hyper-V) 1TB Boot Drive (storing VHDs for boot drives of VMs) - possibly in a RAID 1 with my other 1TB drive 5x 2TB drives (1x 2TB drive hot spare), totalling 10TB, directly attached to a Windows 7 VM, for use of homegroup for this array. In the past, I directly attached the windows dynamic volume to a Windows 7 VM, and performance was abysmal. The question is, with hardware RAID, will it really make that much of a difference? Server specs: Intel Core 2 Quad Q9550 2.83GHz Asus Maximus II Formula (PCI-E x16) 8GB DDR2 RAM PC2-6400 (Yes, I know its a bit out of date)

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• Windows 7 BSOD on boot after windows update

  - by Razor Storm

  After Windows updates today, I restarted my desktop (for the first time in a couple weeks), and on boot up ran into a BSOD: STOP: 0x0000007E (0xFFFFFFFFC0000005, 0xFFFFF8000355AB5A, 0xFFFFF880031CB3A8, 0xFFFFF880031CAC10) I tried system restore, but there was only 1 restore point which was from all the way back in January. I tried it anyway but after 10 minutes of running it said system restore could not be completed. Additional info: I checked my BIOS and it is detecting my rams. CPU is Intel Sandy Bridge i5-2500k overclocked to 4.3GHz. I reclocked it back to stock speeds (3.3 GHz) in case it was causing the issue (I highly doubt that it is). But the problem persists. Running Windows 7. 12 GB of RAM at 1333 MHz OS on 64gb SSD. What is causing this? How should I fix it? Also, if it is caused by windows update, is there a way to undo the update with command prompt? I tried safemode, and the blue screen comes up as well, but I am able to access command prompt.

  Read the article

• Installed Bunch of New Fonts on Windows 7 - Now None Show Up and System Lags

  - by Josh Stodola

  So I went to install about 5,000 fonts on my Windows 7 64-bit machine. It was slow to install them, and I had to leave. I came back and my PC was shut down, and I had to go through the Windows recovery BS when I powered it on. Now my computer runs EXTREMELY slow and any program that has a font menu locks up my whole machine (nothing in Microsoft Office works). When I go to "Fonts" in the control panel, it says 0 items. I went through all of the font settings trying to get them to appear. Nothing helps. I tried to bring up the Character Map and that froze up my machine too. How can I fix this? If I do not get this issue resolved soon, I am wiping this drive and going back to XP (and probably never purchasing another version of Windows again). I never had any issues with XP and have had nothing but performance problems when switching to Windows 7. My quad-core intel extreme with 8GB of RAM should never flinch with the kind of work that I do, and something simple like playing a song off an external HD takes up to five seconds on Windows 7. Unbelievable that I had to pay for this crap!

  Read the article

• AA doesn't work due to monitor?

  - by MikeQ

  I have a monitor (with TV tuner - Philips 221T1SB), native resolution of 1920x1080, but there is an Overscan in Catalyst. It says from left to right '10%' and '0%', if i set it (all the way to the left) on 10%, i get screen with black borders (you know what i mean), but if i set it to 0%, i get a filled monitor. It does make sense, but why the hell is there such an option? I never had any AA issues before, but now, with this monitor, here they go. I can't find any solution, i have only one lead = overscan, or pretty much anything with the CCC settings. Yes, i almost forgot. After a bit of trying to configure the monitor with remote, i found there is a PC channel option, few other channels, and then a HDMI option. I have monitor through HDMI, but why i get black screen when i select the PC channel? That might be another problem. I tried almost everything. Please guys, give me a hand. I don't want jaggies! CPU: Intel I5-750 @4,0GHz RAM: Corsair Vengeance 8GB 1600MHz GPU: AMD Gigabyte HD 7950 Windforce @1100/1400, 1,174V Motherboard: ASUS P7P55D-E EVO

  Read the article

• CPU usage always below 10% in windows server 2008 r2 x64

  - by ???

  I am using a server with windows server 2008 r2 running on it to run my program. The CPU of the server is Intel xeon x5570 2.93GHz with 2 processors, 8 cores per processer. However, I found that the cpu usage is almost always below 10% even I use 32 threads in my program. And I also found that sometimes the cpu usage could reach as high as 93% through the task manager when running my program and at that moment my program has processed over 1000 files per second while normally, it only processed over 50 files per second. However, this does not happen often. I use tools downloaded from the internet to make sure no core sleeps when the server is on, nothing changed. Also, I edited the windows register to make sure that I, as an administer, have no cpu usage limit. But it changed nothing. Is there anyway that I can make full use of my cpu? That is to say that each core runs a thread of my program and the total cpu usage could reach over 50% when I use a reasonable number of threads in my program. Did this happen to anyone of you? And could you help me with this ? Thank you!

  Read the article

• Blue screen of Death on Install

  - by Toby Allen

  I have a machine with Windows Vista Installed. It has an Intel X25 SSD as the System Drive I want to reinstall (I plan to format and overwrite Vista) with XP. When I boot up using the Dell XP CD it loads the initial drivers then i get a Blue Screen. This is quite concerning. The installed OS works ok, but its giving problems so I want to remove it. Should I just format the SSD and try again? Will this make any difference? Can I do something to avoid hitting the Blue Screen? Its possible I had corrupt sectors on one of the other disks, will a new XP install use the System drive or drive 0? Can I force the install to use a specific drive when installing? Error: *** STOP: 0x0000007B (0xF78D2524,0x0000034,0x00000000,0x00000000) I never did find the answer, however I removed the SSD and tried to install on other disk - CRASH I disconnected the other disk and tried to install with only SSD plugged in - CRASH I removed 1 block of RAM - CRASH I used a windows 7 CD - NO CRASH

  Read the article

• No sound out of headphone port

  - by Thanatos

  I cannot get sound out of the headphone port. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller

  Read the article

• Second CPU missing of Dual Core

  - by Zardoz

  My Lenovo T61 has a dual core CPU. I just noticed that under Ubuntu 10.10 only one CPU is recognized. I know that once both CPUs worked. Not sure since when the second CPU is missing. Maybe since the last kernel update. Currently I am using linux-image-2.6.35-23-generic (for x86_64). What can I do to enable the second CPU again? Here the ouput of /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping : 6 cpu MHz : 800.000 cache size : 3072 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 4189.99 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: Any help is welcome. I really need that CPU power for my work here.

  Read the article

• after building in more ram, bios/debian does nothing [closed]

  - by derty

  My private server has 2x1gb Ram working with a 64bit Debian and an Q6600 Intel. This runs 2 virtual mashines on it each one recives 512mb RAM. Which you can immagine is a bit tight for the hole system. Now i got 2x2gb ram from a friend. I'm not sure if thery are clocking at the same speed, but i'm sure my power adaptor is not on his limit and can handle that. So there are 2 ram sockets left at the mainboard. I shuted down the system and build in the 4 gigs and looked what happen. After pressing the start button, everything gets noisy as known BUT the screen shows nothing, not even the bios stuff it usally does. Why isn't the system booting? I can immagine that it does not direkt link between booting debian and the bios not showing a thing. Or is it Grub? I mounted the system disk, and i can see it, switch folders write stuff with "vim" it does not seems like there is a problem.

  Read the article

• USB 3.0 ports backwards compatibility problems with 2.0 devices?

  - by AaronLS

  I see some info on the net that suggest that I should be able to get my USB 2.0 devices to work in 3.0 ports. I only have two 2.0 ports on my new computer, and six 3.0 ports. I have installed drives. There's two different drivers, I guess some of the ports are supported by the intel board and some supported by some other chipset on the motherboard. I however have yet to get any of the 3.0 ports to work, and my brother had had the same issue with his devices not working in 3.0 ports on his computer. So I am beginning to wonder if the backwards compatibility isn't reliable for some reason. Maybe manufacturers opting not to implement 2.0 support on the 3.0 ports. I understand that physically the wiring is there, but that is only half the story. Beyond my brother's and my own computers (different motherboards/everything), I have yet to see a 2.0 device work in a 3.0 port. Is there any reason for this apparent device incompatibility? I.e. looking for responses that would indicate what areas to explore for issues or if there is any known cases of manufacturers deviating from spec in hardware or drivers. I am aware it's "supposed" to work :) Update: Does this have any relation to "USB Legacy Support" options in the BIOS? There several options combinations of options with "USB Legacy Support" and "USB 3.0 Legacy Support" and the description for these is a bit confusing, sounds like a bad translation.

  Read the article

• Windows 7 not booting after failed SRT (SSD caching) install

  - by david

  This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

  Read the article

• Disk operations in windows 7 are slow

  - by Skadlig

  My computer started lagging last Sunday. I tried to reboot it and it failed. Trying to boot into failsafe mode takes around two hours. It mainly freezes on two files: scsiport.sys and classpnp.sys When it finally has started all disc operations are really slow. When it has run for a while it goes faster, probably due to data moved into RAM instead. It froze on an other file before that was associated with Avast but uninstalling it didn't really help. A critical windows update was installed on Sunday but rolling back the update didn't help. I had a guess about the sound card but disabling the sound card drivers also didn’t help. I have an inkling of an idea that it might be Intel rapid storage technology that might be acting up but it doesn't allow me to reinstall it from failsafe mode and I haven't been able to log into normal mode for a while. I would appreciate suggestions regarding how to get into normal mode again and/or what can be the root cause.

  Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >