Search Results

Search found 8336 results on 334 pages for 'today'.

Page 161/334 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

• How many virtual processors or cores should I assign to my Guest OS?

  - by reidLinden

  I've just received an upgraded Host machine, and am looking to push some of those advances to my workstations Guest OS(s). In particular, I used to have a single processor, with 2 cores, so my Guest OS only had 1/1. Now, I've got a single processor with 8 cores, so I'm curious about what would be recommended for my Guest OS now? 1 processor/4 cores? 2 processors/2 cores? 4 processors/1 core? My instinct says to stick with the number of physical processors (or less), but, is that based on reality? I spent a good while looking for an answer to this, but perhaps my google-karma isn't in my favor today.

  Read the article

• Could a too low voltage during long periods damage my computer fan?

  - by Sopalajo de Arrierez

  Computer fans use to run at 12Volt, but most as for today they allow 9Volt or even less to slow down the fan speed (RPM, Revolutions Per Minute). In cases of too low voltage, the fan stops, but I can see it "trying to start again". For example: my Tacens 9dB fan stops at about 10 Volts, but to start it again, 10.5Volt is not enough, and the engine tries to move the fan (I can see a small movement as an "attempt" to move) each 1-5 seconds, but it does not succees, so the fan keeps at 0 RPM. Maybe that "attempt" to move could damage the internal engine of the fan when it last for hours or days?

  Read the article

• Upgrading Windows 8 Consumer Preview to Release Preview

  - by user1407016

  I currently have my main hard drive split into two partitions. One being Windows 7 with about 600 GB of memory, the other Windows 8 Consumer Preview with about 50 GB. As you can guess it is set up for a dual boot. Today while looking up how to get the C# Facebook SDK for Metro apps I learned about the Release Preview being released. I was wondering: How do I go about getting rid of Windows 8 Consumer Preview and replacing it with the Release Preview? I know i can't just wipe it off my second partition because the dual boot uses Windows 8 to choose the operating system to boot.

  Read the article

• What program is making this sound and how can I make it stop

  - by DrFredEdison

  Some program is intermittently making this weird "chook ... chick" sound, no more than every 5 minutes, but sometimes hours or days between making it. There seems to be no pattern as to when it happens, but the sound is definitely coming from the speakers, and is always the same, so I'm pretty confident some piece of software I'm running is playing the sound. Today, I managed to record it, and I've posted it here: http://tristanhavelick.com/chook-chick.mp3 Short of closing my programs one by one, and seeing if the sound continues, are there any tricks for tracking down a problem like this? Is there any software that can trace what sounds come from what programs (something like tcpview with waveforms)? I am running windows xp.

  Read the article

• Couldn't dual boot Vista and Centos 5.4

  - by jack sparrow

  Hi all, Today I have installed Centos 5.4 with dual boot with Vista. Everything was fine, but after testing Centos 5.4, when I tried to load Vista, it did not load. After selecting vista from grub menu, it shows the following message: rootnoverify (hd0, 1) chainloader +1 No bootmgr found I googled and try to fix the boot but failed, Then I restart my machine, boot with vista cd and in rescue option, restore my bootmgr by typing bootrec /fixmbr What happened after that, I can load at vista now, but no grub menu shows :P It seems the Centos went totally invisible. I am using dual booting Ubuntu 9.10 and vista in my laptop and its working fine and with no error from the beginning. But installed Centos for one of my project needs and I need it running asap. So I am feeling very helpless. Please help me anyone out there. I know there are many people knows how to fix it. Please help me.. Thanks in advance.

  Read the article

• odd system name showing up in terminal

  - by sam

  Ive been working on some command line stuff with an external developer through team viewer for work, to interact with th CL i use terminal on OSX, when working with the developer i was always watching what they were doing and i also have all the bash history. Usually upon opening terminal i get something like this Last login: Tue Sep 17 21:33:02 on ttys001 You have mail. unknown-5c:00:00:00:00:00:~ sam$ (note ive replaced some characters in the last line with 00) But today when i opened up terminal and i get this Last login: Mon Oct 21 16:49:35 on ttys000 You have mail. richies-ipad:~ sam$ Note it now says richies-ipad - any idea why this is ? I dont know any one called richie let alone let them have access to my machine. Is this something to be worried about - the fact that someone has enough access to change that ? Also what does the ttys001 part on the first line mean ?

  Read the article

• Firefox 3.5 Doesn't Load CSS From a Specific Site

  - by chmurli

  Firefox 3.5 doesn't load the CSS from only 1 site (www.makeuseof.com). Everything else works OK (graphics, etc.). I tried safemode but no luck. In other browsers same site works properly. What did I do wrong? Edit (2009 Aug. 19): problem solved but I don't know how. Today I just discovered that site loads CSS and it works. I didn't make any changes (think so). Love Firefox :).

  Read the article

• Web-based (intranet / non-hosted) timesheet / project tracking tools

  - by warren

  I realize some similar questions have been asked along these lines before, but from reading-through them today, it appears they don't match my use case. I am looking for a web-based, non-hosted time and project tracking tool. I've downloaded Collabtive and Achievo so far, but am looking for other suggestions, too. My list of requirements: runs on standard LAMP stack non-hosted (ie, there is an option to download and run it on a local server) not a desktop/single-user application easy-to-use - my audience is a mix of technical and non-technical folks easy to maintain - when time for upgrading comes, I'd really like to not have to rebuild the app (a la ./configure ; make ; make install) needs to support multiple users free-form project additions: we don't have a central project management authority (users should be able to add whatever they're working on, not merely from a drop-down) Does anyone here have experience with such tools? It doesn't have to be free.. but free is always nice :)

  Read the article

• Diagnose Slow Video Playback during Editing [closed]

  - by chadejah Hunter

  Possible Duplicate: I Want To Start Editing Videos But My Computer Moves Slowly I am using Windows 7 Home Premium on a PC with AMD 64bit Athlon Processor 2850e @ 1.80GHz, 2GB RAM, and a NVIDIA GeForce 6150SE nForce 430 graphics card I am using Pinnacle Studio 15 HD Ultimate. While editing videos the program moves normally but the playback is slow. When I press play the sound is normal but the picture is really slow and choppy. When the sound ends the picture continues to play and it speeds up. I updated the video card today, restarting the PC but get the same behaviour. Does anyone have any suggestions what I can do to get video working smoothly while editing?

  Read the article

• Why are my files in /var/lock and where did they just go?!

  - by Nicky Hajal

  I am hosting a website on Debian 5.0 & Apache2. Today one of my websites was down, Apache said it couldn't find the directory. I located the files and the whole site once in /var/www/site was now /var/lock/site. All the files were present. I was confused, but figured I'd just move it back. mv /var/lock/site /var/www All looked fine... Except that only the directories moved and the files appear to be lost! I am working on restoring from backups but I would really love to know what happened and where my files went (the backups are a few days old). Thanks for your help!

  Read the article

• Can't add printer on Windows XP

  - by SuperFurryToad

  I've added a HP 4250 printer to about half a dozen Windows XP PCs in our office without any problems whatsoever, but for some reason I haven't been able to add it to one particular PC today. I go through the Add Printer wizard to add a local printer attached to the PC, enter the new port number as a Standard TCP/IP Port, install the driver. At the end of the wizard I get the following error message: Full error message: "windows cannot connect to the printer. either the printer name was typed incorrectly, or the specified printer has lost its connection to the server." This doesn't make any sense as I am able to ping the printer from the PC. The print spooler is running, and any firewall software on the local PC is switched off.

  Read the article

• Windows server 2008 r2 console stuck at "waiting for user profile service"

  - by support

  Hi, I have a windows 2008 R2 server, running on dell poweredge t300. Using hyper-v to run a windows 2008 R2 server also. Suddenly, today, my virtual console (on the virtual copy of windows 2008 server r2) will not let me login as administrator. It starts to login but then sticks at the message: Please wait for the User profile Service and is unresponsive to keypresses (incl ctrl-alt-del). The only way out is a crash. It starts up in safe mode without networking ok but not in safe mode with networking. Any suggestions on how to fix this would be appreciated Thanks

  Read the article

• What does "Endcode #816" stand for in Canon iR-ADV C5035 printer logs?

  - by Odin Kroeger

  We are using the Canon iR-ADV C5035. Today a worker has reported that some Word documents cannot be printed via that device (others do). I could confirm that and found that the Canon iR-ADV C5035 logs showed an "Endcode" "#816" for every print job that was not printed (whereas other print jobs show an "Encode" "OK"). Unfortunately, neither the manual that came with the Canon copy machine nor the web seems to know what this "Endcode" means. Canon support has been informed, but I'm still waiting for them to call me back. Does anyone know how I could find out what this "Endcode" stands for? Or, preferably, where I can look up the meaning of such Canon "Endcodes" in the future? Thanks in advance for any hints.

  Read the article

• Why does restarting the modem fix latency?

  - by Giovanni Galbo

  In the last few days I've noticed poor internet performance. Today I ran a speed test and the results were abysmal... 10mb down and 0.18mb up (which really hurt, because I was trying to RDC from another location). I pay for 30mb down and 5mb up. Latency was at 128ms. Before calling my ISP to give them a verbal lashing, I unplugged the modem and plugged it back in. I pretty much got top speed after doing that (with a latency of 7ms). I'm the type of guy that likes to know what goes on under the hood. So what's the deal? What mysterious powers does restarting give to my modem?

  Read the article

• Excel 2007 Constantly Creating Custom Cell Styles

  - by Nick

  Hello, I've been using Office 2007 for a few months now and have noticed that it was creating duplicate custom cell styles on its own, like Normal 2, Normal 3, etc. It didn't really bother me at first, but now Excel will lag when I open the cell styles menu as it gathers well over a hundred of these duplicates (I have seen Normal 54 and Normal 5 2 2 so I'm unsure as to how many there actually are). I have also just checked a fresh Excel sheet, and it only has the defaults, but one I created earlier today from scratch has the Normal 54 listed. My questions are: Why is this happening? Can I delete a temp or custom settings file somewhere to clear this? Any help on this is appreciated.

  Read the article

• samba shares dissapear everynight

  - by Crash893

  I have ubuntu 8.04lts and recently a weird problem has been cropping up. every night something happens and in the morning my coworkers cant see the shares. If i try to remote into the machine via ssh i don't get a prompt . when i rebooted the machine i would get a "video cannot be displayed in this mode" screen and no other activity on the box. I booted from grub into recovery and tried doing a package repair (keeping my smb.conf) and that didn't seem to do anything after a few other reboots I was able to get it to come up (im not sure what i did) yesterday it did teh same thing i booted to recovery then did a repair xserver and it came right up so i thought that resovled the issue but then today same thing anyone have any idea on what i can look for (im very new to linux in general) worst case sennerio can i just reinstall ubuntu over again with out blowing out the data?

  Read the article

• Can't change user security on folder - Business Objects XI 3.1

  - by Chris W

  I've got a single folder within the list of All Folders that I can't change any user permissions on. I'm logged in as an admin and when I view security for the folder it says I have full rights to the folder yet i can't change anything on it or it's sub folders even though it clearly shows me as having rights to "Modify the rights users have to objects". As a test I added a new sub-folder called Test which created ok but I'm not able to then delete the sub folder or change it's permissions either. Interestingly we changed permissions on one sub-folder last week without issue but when I check that folder today I now can't update it. Any ideas anyone?

  Read the article

• Will Vimperator always be this awesome?

  - by Martín Fixman

  About a week ago I started using Vim, and fell completely in love with it. However, today I installed the Vimperator extension on Firefox, and through there are some problems (all of which will be solved after using it until I get used to it), I found it great. However, I'm still in the "Holy fuck this is totally awesome" phase of software testing, and in some time will go back to the "I have this thing" phase. Just to be sure, will it be a good idea to use it regularly? I want to hear experiences about users and ex-users.

  Read the article

• Installing Sharepoint 2007 on Windows Server 2008 R2

  - by ronischuetz

  we are using in our lab a clean installation of Windows Server 2008 R2 which is running as Hyper-V instance. Today we wanted to install a clean installation of Sharepoint 2007 with SP1 on this machine and we explorer an error that we are not able to install it. The setup is comes up with an error which is described here: http://support.microsoft.com/kb/962935 but this is not our szenario. A printscreen of this message can be found here: http://www.ronischuetz.com/images/SP_2007SP1_Inst_Error.png @Microsoft, my personal point of view is that it cannot be that we need to install first 2008, then Sharepoint 2007 with SP1, then SP2 and upgrade to 2008 R2. Nobody is going be happy with this solution and I hope we find a fast way how customers can install Sharepoint direclty on 2008 R2. Anyway, thanks in advance for any further information how we should go on with this issue. The issue is listed here: http://social.msdn.microsoft.com/Forums/en-US/sharepointadmin/thread/91a6be50-9009-43c8-a37c-66cfb83d738f

  Read the article

• How do I recover tab cycling in Terminal.app?

  - by Grzegorz Adam Hankiewicz

  Today I've noticed that Cmd+} has stopped working for me in Snow Leopard's Terminal.app as a shortcut to cycle to the next tab. Cmd+{ still works. I've gone to the Preferences-keyboard shortcuts and when I try to create a new shortcut pressing Cmd+} I get Cmd+alt+Ç in the window. I get Cmd+alt+´ when pressing Cmd+{ (I'm on a Spanish macbook pro). I've also noticed that I cannot create a custom shortcut for Terminal.app, because it is not in the list of applications I can create shortcuts for, and neither can I add it to the list. How can I debug what is "eating" the cycle right tab shortcut key? I've got sizzling keys plugin, keyboard remapper (for the esc/capslock key) but I've tried disabling them and still didn't recover the terminal shortcut.

  Read the article

• What happens to running processes when I lose a remote connection to a *nix box?

  - by David Marble

  I occasionally lose my remote SSH connection to my VPS. I use screen for long-running processes, but am wondering what happens to the processes I had running aside from those run within a screen session if I lose the connection to the box. When I re-establish a connection to the box, what happened to the bash and sshd processes that were running when I lost the connection? Today I lost connection repeatedly and noticed many more bash and sshd processes than usual. If there are processes hanging around, do I need to kill them? How could I determine which processes were abandoned from my previous session? Thanks for any replies!

  Read the article

• What are the effects of the L root server now publishing DURZ?

  - by brent

  I'm curious what the actual effects of the L root server publishing DURZ today will be. On the nanog mailing list, someone said it's important to evaluate the systemic effects of root name servers publishing signed zones, even when not using DNSSEC. Meanwhile, RIPE's own published information on their changes to the K root server say there's no issue if your resolvers don't use DNSSEC. Can someone please clear this up? DNSSEC seems to be a messy, tangled web. If not enabling DNSSEC on my resolvers, do I have anything to worry about with the upcoming changes to the root servers?

  Read the article

• Computer cannot detect hard disk

  - by Nrew

  Details: BIOS: AMI Bios, set primary master to Auto OS: Windows XP Sp2 Memory: 384 Mb Processor: Pentium 3 yeah this one is really very old. And some of the capacitors in the motherboard are already bulging. It detected the hdd yesterday when were trying to fix it and install xp. But today it cannot boot and said: Boot failure. What can you suggest that I would do to revive this old machine. What would be the problem, is it the hdd, the ide cable or the motherboard.

  Read the article

• Citrix Access Gateway not redirecting to login URL

  - by Dave

  We have an older setup for XenApp - users log in through Citrix Secure Gateway running on a windows box. (We hope to start using a NetScaler soon.) Earlier today, connections to https://citrix.company.com/ starting throwing up a 503 error page, instead of redirecting to https://citrix.company.com/Citrix/XenApp/ If you go directly to the /Citrix/Xenapp/ URL, the user is properly directed to the login page, and can launch apps. We've restarted the service, and rebooted the server. We haven't yet tried uninstalling and reinstalling the software. Before we do this, I'm looking for ideas as to how we can get the redirect working again without a fairly major outage window. To make things more interesting, many of our users have Citrix Receiver installed, also pointed at https://citrix.company.com/. Receiver makes itself the default launcher for ICA files, and gives a connection error when it tries to load apps - probably because of the same non-functional rediect?

  Read the article

• Debian date jumping, causing complete lockup

  - by artfulrobot

  I have a Debian Squeeze VM that has suddenly chosen to jump it's date forwards just over a month, which seems to confuse it no end and cause it to require a hard reset (yikes!). There is nothing unusual in the logs, except that the datestamp suddenly jumps (today back to 2005). It's happened three times, so I don't think it's to do with the leap second issue as the last one of those was in July. When it happened once I spent ages checking stuff but could not find anything, decided to forget it. But three times is becoming an issue on a production server. Edits providing information requested in comments (thanks!): I do not have control over the hypervisor, it is a hired VM. # cat /sys/devices/system/clocksource/clocksource0/current_clocksource kvm-clock # ntpq -p remote refid st t when poll reach delay offset jitter ============================================================================== +grendel.exizten 130.149.17.8 2 u 29 64 77 14.811 1.778 1.744 *panoramix.linoc 193.67.79.202 2 u 32 64 77 19.729 -0.419 1.691 +robert.elnounch 213.251.128.249 2 u 27 64 77 17.762 0.600 1.722 -janetzki.eu 83.169.43.165 3 u 31 64 77 27.214 3.575 1.638

  Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >