Search Results

Search found 4572 results on 183 pages for 'dual monitors'.

Page 163/183 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

• Privacy, VPN and routers

  - by user123189

  Ever since this ACTA push-up the things are starting to heat up around torrents and privacy. I am using Tribler now, but this is not secure enough for me. Not enough privacy. I've been using in the past a swedish VPN PPTP connection. What I observed is that, when the VPN connection was down, Internet traffic wasn't cut off, rather the downloads were continuing, this time with my real IP, wearing off my protection. 1st : How to enforce a VPN connection that will cut all traffic when down? That is, the moment the connection is down, all internet traffic should cease as if I'd pull the network plug out. 2nd: Is PPTP good enough or should I ask for SSTP or IKEV2 ? 3rd: Should I disable IPv6 ? Is VPN no longer private if I keep IPv6 active? I 'heard some stuff' about dual vpn routers to be able to improve privacy; but nothing more about how to configure one for such a task. 4th: Is there any kind of "black box" hardware equipment that can be used in hiding IP, encrypting traffic and so on ?

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• How can I remotely display images on my computer?

  - by Jakob

  What I Have: A laptop booted with Ubuntu and a stationary computer dual-booted with Ubuntu and Vista, both connected through a wireless ad-hoc network. What I Want: I want a way to display images in fullscreen on my stationary, using my laptop as a "remote control". I want to be able to choose another picture at any time and have my stationary computer remain in fullscreen mode at all times. Preferably, I should also be able to display just an empty (black) screen. How can I arrange for this? What I Have Tried: I have tried simply SSH:ing into my stationary computer and opening the image files using an image viewer, but all of the ones that I have tried (Eye of Gnome, Mirage, Gwenview, and others) open a new window for every new image. I don't know how to force them into using a single instance. I have tried using the VLC remote control command line interface, but apart from seeming somewhat unreliable (exiting with segmentation faults at one point), it also displays some images with a green border and forces me to pause playback in order for the image to remain on screen. Bonus Question: In my final setup, I also need to play music through my stationary computer's speaker and have the ability to switch to another track at any point, like with the images. Preferably, I would like to control the images and the audio through the same interface. How can I best achieve this?

  Read the article

• Home Server: storage virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on storage management. (I have another question related to the VM/compute instance management). Here my environement and wishes. Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) with 1 250GB system disk and up to 4 HDD (2 TB) for "data" OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine The 4 HDD is going to be a software RAID array, probably RAID 5. storage should be "virtualised/cloudified": easy to extend: if I add a NAS on the network, I can include the NAS space capacity within this storage space as one virtual disk. This can be a NAS, an external HDD or another server. cluster FS or S3 style space or OpenStack block storage? Whatever is easier to manage/maintain and easy to integrate/plug to VM/compute instance. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. Note: the VMs I intend to run on top of this server are one dedicated to backup, one for a "owncloud/dropbox"-like service and perhaps one for media server (hosting video and photos). I'm not sure if traditional VMs or compute instance are the most suitable for this.

  Read the article

• Proxmox drbd configuration split brain [on hold]

  - by AudioDan

  I am planning a proxmox HA configuration with two Dell R710 machines (dual 6 core processors in each) with enterprise level drive raid arrays. I would be using DRBD with a quorum disk on a third machine. I would dedicate two 1GB nics on each server to the DRBD communications. We would have approximately 12 to 14 Virtual Machines running on this pair of servers. The proxmox manual recommends creating two DRBD resources - one for the Virtual Machines that normally run on ServerA and one for the Virtual Machines that normally run on ServerB. This is because of the Primary/Primary state in which this configuration runs. If both servers have VMs talking to the same DRBD resource and a split brain situation occurs, there is potential for data corruption that must be resolved. While I understand it would take more effort to create new virtual machines, can anybody foresee any potential problems with running a separate DRBD resource for each VM instead? Does anyone have experience running a setup that way and has it worked well? It seems to me that would allow more flexibility in moving machines back and forth.

  Read the article

• Ubuntu network card problem.

  - by Steve Greene

  Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

  Read the article

• Ubuntu 12.10, Unity, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL detection of multiple gpus

  - by junkie

  I'm using Ubuntu 12.10, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL. I have three amd radeon 7990s plugged in each of which are a dual 7970 so I have six gpus altogether. I plan to go up to eight in a few days. Windows couldn't use even 4 but linux works fine with 6 so far. The strange thing is that the six gpus are only detected by OpenCL in unity (the ubuntu default window manager). If I switch to e17, blackbox or fluxbox or anything else for that matter OpenCL only detects one. I'm using a simple OpenCL program to list all devices to check. I've also checked the output of aticonfig --list-adapters, fglxinfo and clinfo. The first two always show six in all window managers wheras clinfo shows 6 in unity but 1 gpu in all other WMs. I'm also using an X config generated by aticonfig --initial -f --adapter=all. I'm also only using one monitor. I've also checked using lsmod that the fglrx module is loaded in all WMs. So I have two questions. Why does OpenCL see six gpus only in unity? How can I enable six gpus on other lightweight WMs? Basically I'm getting at what determines how many gpus the OpenCL runtime sees? Thanks.

  Read the article

• How to verify power provided to processors is clean

  - by GregC

  Once in a blue moon, I am seeing a blue screen of death on a shiny new Dell R7610 with a single 1100 Watt Dell-provided power supply on a beefy UPS. BCode is 101 (A clock interrupt was not received...), which some say is caused by under-volting a CPU. Naturally, I would have to contact Dell support, and their natural reaction would be to replace a motherboard, a power supply, or CPU, or a mixture of the above components. In synthetic benchmarks, system memory and CPU, as well as graphics memory and CPU perform admirably, staying up for hours and days. My questions are: Is power supply good enough for the application? Does it provide clean enough power to VRMs on the motherboard? Are VRMs good enough for dual Xeon E5-2665? Does C-states logic work correctly? Is there sufficient current provided to PCIe peripherals, such as disk controllers? P.S. Recently, I've gone through the ordeal with HP. They were nice and professional about it, but root cause was not established, and the HP machine still is less than 100%, giving me a blue screen of death once in a couple of months. Here's what quick web-searching turns up: http://www.sevenforums.com/bsod-help-support/35427-win-7-clock-interrupt-bsod-101-error.html#post356791 It appears Dell has addressed the above issue by clocking PCIe bus down to 5GT/sec in A03 BIOS. My disk controllers support PCIe 3.0, meaning that I would have to re-validate stability. Early testing shows improvements. Further testing shows significant decrease in performance on each of the x16 slots with Dell R7610 with A03 BIOS. But now it's running stable. HP machine has received a microcode update in September 2013 SUM (July BIOS) that makes it stable.

  Read the article

• Any dangers in using DDR memory with a higher frequency than the FSB?

  - by raw_noob

  I'm looking to upgrade memory in an older motherboard. The processor is an AMD Sempron 2500+ with a maximum speed of 333/166MHz. The motherboard is an MSI MS-7061 (KV3M-V), which accepts up to 2Gb of DDR memory maximum PC2700 in 2 slots and has a maximum FSB of 333MHz. The board does not have dual-channel support. Existing memory includes a stick of 512Mb PC3200, which seems to be running OK (presumably at PC2700) but is rated 200MHz, which is below the FSB speed. The other stick is 256Mb PC2100/133MHz, again below the FSB speed. (All figures from CPU-Z.) I have a chance to acquire a single used stick of PC3200/400MHz memory very cheaply. Crucial's system scanner seems to suggest that this will be OK with my system, but other sites have suggested that running memory with a higher frequency than the FSB can cause instability. Is this true? Would I be better waiting until I can buy the correct PC2700/333MHz stick? I'm assuming that the mixed memory I have at present is running as 768Mb at 133MHz. Is this a reasonable assumption? If so, would you expect the performance differences between 768Mb/133MHz and 1Gb/333MHz to be very noticeable? If I install the new 1Gb/400 or 333MHz stick in slot 1, am I right in thinking that adding back the existing 512Mb/200MHz stick in slot 2 would pull the whole 1.5Gb system memory speed down to 200MHz? If so, which would be better - 1.5Gb/200MHz, or the single 1Gb stick at the full 333MHz that the FSB permits? Is more headroom more important than extra speed? Any help - or even opinions - gratefully received. I can't find reliable information, and I can't afford to make expensive mistakes.

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• Advice on Computer Specs for overall development/general use machine

  - by Ender

  At the moment I am restricted to a laptop with 512MB of RAM, a 120GB HDD and a 1.5GHz Intel processor for all my development and general browsing needs, and as you can probably tell using it for anything modern is a painful experience. As a result I've decided to buy myself a new desktop computer, one that will stand the test of time and one that can be upgraded easily. Rather than build the machine myself I've decided to go through Dell as I've had good experiences with them when purchasing computers for my family. I've had my eye on this as it's got a good amount of RAM, has a decent-rated processor and isn't priced too badly. http://www1.euro.dell.com/uk/en/home/Desktops/inspiron-580/pd.aspx?refid=inspiron-580&s=dhs&cs=ukepp1&~oid=uk~en~20211~inspiron-580_d005827~~ Intel® Core™ i5 Processor 750 (2.66GHz, 8MB) Genuine Windows® 7 Home Premium 64bit - English Display Not Included ATI Radeon™ HD 5450 1GB DDR3 graphics 6144MB Dual Channel DDR3 [3x2048] Memory 1TB (7200rpm) SATA Hard Drive DVD +/- RW Drive (read/write CD & DVD) with DVD Burn software 1 year of coverage included with your PC McAfee® Security Centre - 15 Month Protection - English After the pain of using a slow laptop for all this time the main thing I want is speed. I may look to play a couple of basic games on it, nothing too powerful. Obviously I'll be doing some development on it too so it'll have to be able to handle the latest IDE's and Database tools like SQL Server pretty quickly. Finally, should I ever need to improve it I'd like to be able to add more RAM and change some of the parts. I wouldn't have thought this would be a problem but a few people I've spoken to have said that the amount of RAM the motherboard can handle isn't that great. Is this true? How long can I expect to be using this computer before it's too slow? Thanks in advance for the help.

  Read the article

• Windows 8 Fails to install with corrupted graphics

  - by Andy

  I am trying to install Windows 8 Pro Upgrade via the download method on an older PC (07-08). It is a Dell Dimension E521 but it has been upgraded with a 3.0 Ghz Dual Core AMD Processor, 120 GB SSD, and 4 GB of RAM. The Windows 8 upgrade assistant did not detect any issues or concerns with upgrading other than I don't have DVD software installed. The system install Windows 8 but on the first boot, corrupt graphics are present. Eventually, the monitor will go into sleep mode and then roll back to Windows 7 Pro X64 which runs fine. I wouldn't be upset over not being able to install Windows 8, but I already paid for the software since I thought there would be no issues upgrading. The Graphics card in the system is the Geforce 7300LE and it has the latest NVidia drivers for Windows 7 loaded. I saw this solution which is similar to my problem: Corrupt graphics during Windows 8 installation However, I have downloaded Windows 8 and I am not sure how to go about modifying the install that resides somewhere on the hard drive. Thanks in advance for any assistance.

  Read the article

• Linux Live CD only works when Windows is in Legacy mode?

  - by Vee

  I have asked a similar question before and no one was able to help me but I think it was because I wasn't phrasing it properly. This is a better restatement of the question. I have Windows 8 and Linux Mint dual booted on my pc. When I tried to boot the Linux from a CD ROM only, it would give me the following error: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... The Linux Mint works fine but otherwise, but it gives this error when I try to boot from CD. The boot Linux from CD only worked when I changed the Windows to Legacy mode in the BIOS settings. When I changed it back to UEFI, it would give the same error. Why is this? How can I fix it? I am somewhat new so is there anything else I should know about all of this? NOTE: I changed the Linux into UEFI mode using boot-repair but that still did not solve the problem when I tried to boot from CD ROM.

  Read the article

• How to migrate WinXP from failing old HD to new one

  - by Péter Török

  Following this issue, we have all our important data backed up now. I also bought and installed a new replacement hard disk (WD 160GB PATA) as secondary (slave) drive. I created two primary NTFS partitions on it: a 40 GB system partition, and a 110GB data partition. In theory I could start reinstalling WinXP from scratch on the new system partition, then copying over all user data from the old drive to the new data partition. Once this is done, I could even throw away the old drive, or keep it just to see what happens. (Note: I don't want to clone the whole drive as it contains a dual boot setup with an old Linux installation which I don't need anymore, and anyway, a fresh reinstall would do WinXP good to get rid of many years' clutter.) However, I am lazy :-) The old HD is still functioning, the problem has not manifested again since. So I feel there is no need to hurry with a complete OS reinstall. What I don't know though is whether I will be able to install WinXP on the new system partition at a later stage without affecting the contents of the data partition on the same drive. If this is possible, I can just move over all our data to the new data partition to have it safe, then continue running WinXP from the old drive as long as it works. Does anyone see any problems/risks with this plan?

  Read the article

• How can I setup a Proxy I can sniff traffic from using an ESX vswitch in promiscuous mode?

  - by sandroid

  I have a pretty specific requirement, detailed below. Here's what I'm not looking for help for, to keep things tidy and on topic: How to configure a standard proxy Any ESX setup required to facilitate traffic sniffing How to sniff traffic Any changes in design (my scope limits me) I need to setup a test environment for a network-sniffing based HTTP app monitoring tool, and I need to troubleshoot a client issue but he only has a prod network, so making changes to the config on client's system "just to try" is costly. The goal here is to create a similar system in my lab, and hit the client's webapp and redirect my traffic - using a proxy - into the lab environment. The reason I want to use a proxy is so that only this specific traffic is redirected for all to see, and not all my web traffic (like my visits to serverfault :P). Everything will run inside an ESX 4.1 machine. In there, there is a traffic collection vswitch in promiscuous mode that is not on the local network for security reasons. The VM containing our listening agent is connected to this vswitch. On the same ESX host, I will setup a basic linux server and install a proxy (either apache + mod_proxy or squid, doesn't matter). I'm looking for ideas on how to deploy this for my needs so I can then figure out how to set it up accordingly. Some ideas I've had were to setup two proxies, and have them talk to eachother through this vswitch in promiscuous mode, but it seems like alot of work. Another idea is a dual-homed proxy, but I've never seen/done that before so I'm not sure how doable it is for what I'd like. I am OK with setting up a second vswitch in promiscuous mode to facilitate this if need be, but I cannot put the vswitch on the lan (which is used so my browser would communicate with the proxy) in promiscuous mode. Any ideas are welcome.

  Read the article

• Fedora installed in Legacy mode, how to make it work in UEFI?

  - by TryntaLearn

  I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• Ubuntu and Windows and Separate HDs, oh my!

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. Here's a pic of the error I get when I try to boot to Windows: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu. (Someone suggested just reinstalling windows from installation CD. Agree?)

  Read the article

• Connect two networks

  - by Meek Barrios

  Connecting two different offices with a wireless link and linux boxes. Hardware: 2 CISCO RV42, 2 Dual Homed Linux Boxes running debian, 2 2Wire and 2 AirMax 5 Configuration is: Office A LAN A (10.1.1.0/24) -> RV42 A (WAN1 - 10.1.1.254) -> 2Wire A (Internet) LINUX A ( ETH0 (LAN) 10.1.1.253, ETH1 (LINK) (10.1.3.3) Wireless Link --- AirMax A <-> AirMax B connected as Wireless Bridge Office B LAN B (10.1.2.0/24) -> RV42 B (WAN1 - 10.1.2.254) -> 2Wire B (Internet) LINUX B ( ETH0 (LAN) 10.1.2.253 -> ETH1 (LINK) (10.1.3.4) Network configuration is: LAN A - Default Gateway 10.1.1.254 RV42 A - Static Route 10.1.3.0/24 on 10.1.1.253 Static Route 10.1.2.0/24 on 10.1.1.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux A - ETH0 10.1.1.253 netmask 255.255.255.0 gw 10.1.1.254 ETH1 10.1.3.3 netmask 255.255.255.0 gw 10.1.3.1 AIRMAX A - 10.1.3.1 netmask 255.255.255.0 gw 10.1.3.1 LAN B - Default Gateway 10.1.2.254 RV42 B - Static Route 10.1.3.0/24 on 10.1.2.253 Static Route 10.1.1.0/24 on 10.1.2.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux B - ETH0 10.1.2.253 netmask 255.255.255.0 gw 10.1.2.254 ETH1 10.1.3.4 netmask 255.255.255.0 gw 10.1.3.2 AIRMAX B - 10.1.3.2 netmask 255.255.255.0 gw 10.1.3.2 Both linux have ip_forward set to 1 and the following on the iptables: iptables -F iptables -X iptables -P FORWARD ACCEPT iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT I can ping from Linux B any ip on 10.1.1.0/24 segment and on linux A any ip on 10.1.2.0/24 segment however I cannot connect to HTTP or FTP on those machines. From LAN A I cannot see any other network. I'm looking for some advice for this configuration or a better solution. Regards

  Read the article

• Building vs buying a server for an academic lab [closed]

  - by Roy

  I'm looking for advice on the classic build vs buy question. We need a new linux server to run Matlab computation on in our lab (academic). Matlab parallel computing toolbox licence allows up to 12 local workers so we are aiming at a 12 core server with 4GB memory per core (total of 48gb). The system will have an SSD for the OS and a raid-5 (4x2tb) for data. I looked around and found a (relatively) cheap vendor, Silicon Mechanics, that offers a system to our liking (specs below) for $6732. However, buying the components from newegg cost only $4464! The difference is $2268 which is 50% of the base cost. If buying from a company can be thought of as a sort of insurance, basically my premiums are of 50% of the base cost which to me sounds like a lot. Of course any downtime is bad, but the work is not "mission critical", i.e. if it takes a few days to fix it when it breaks its no the end of the world. If it takes weeks to months then its a problem. If it breaks 2-3 times in 3 years, not too bad. If it breaks every month not good. In term of build experience, I set up a linux cluster in grad school (from existing computers) and I build my home pcs but I never built a server before. The server components I'm thinking about: 1 x SUPERMICRO SYS-7046T-6F 4U Tower Server Barebone Dual LGA 1366 Intel 5520 DDR3 1333/1066/800 ($1,050) 12 x Kingston 4GB 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) ECC Unbuffered Server Memory ($420) 2 x Intel Xeon E5645 Westmere-EP 2.4GHz LGA 1366 80W Six-Core ($1,116) 4 x Seagate Constellation ES 2TB 7200 RPM SATA 6.0Gb/s 3.5" ($1,040) 1 x SAMSUNG Internal DVD Writer Black SATA ($20) 1 x Intel 520 Series 2.5" 180GB SATA III MLC SSD $300 1 x LSI LSI00281 PCI-Express 2.0 x8 MD2 Low profile SATA / SAS MegaRAID SAS 9260CV-4i Controller Card, $695

  Read the article

• Installing Ubuntu guest crashes Hyper-V host

  - by Grant

  I have a weird problem that I don't even know where to begin diagnosing. Trying to install Ubuntu to a VM locks up the host system! My setup is: Dell R715 server, dual 16 core AMD opteron processors, 96GB RAM Dell MD3600f SAN Server 2008 R2 Datacenter System Center VMM 2012 There are 5 windows virtual machines running that have had no problems. This is the first linux VM I've tried to create. I setup a VM through virtual machine manager, set the CD drive to a Ubuntu 12.04 server x64 iso, and started it up. It boots up the normal ubuntu install menu, but the second I hit enter on "Install Ubuntu Server", I get disconnected. The HOST machine stops responding to pings. So do all virtual machines on it. It locks up entirely - keyboard on the host won't work, mouse won't move, numlock light won't change. There's no blue screen - the host is sitting at the login screen completely unresponsive. I can't find any relevant logs in event viewer after rebooting. What could cause the host machine to freeze like that? It's not a one time occurrence - it happens every time at the exact same point. Thank god this server isn't in production yet!

  Read the article

• Load is 0, yet site crawls (sometimes). What gives?

  - by Yegor

  I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

  Read the article

• Windows shutting down, CPU maxing out in Windows-7 32-bit? [closed]

  - by Vivek Sharma

  I have no idea, what is happening to my laptop. For last 5-6 times it has automatically shutdown while running, without doing anything serious. And I even do get the message during boot which says - Start windows normal - Start in safe mode It just boots up normal. Few days ago, my screen blinked and it the PC shutdown immediately. After that I was not able to get it started. I got it repaired, the guy said he has replaced the display chip (nVidia-nvs-140), but i seriously doubt that. Now it started working, but would shutdown every 20 mins or so. I have a dual boot, ubuntu-11.10 works just fine. Virus scan on windows shows nothing. I am pasting my perfmon output. My CPU for reason is maxing out to 100% continously, for windows internal processes. Please have a look at the attached file. Strangly now for last 2 hours it is working fine, but i am just writing emails and reading excels. ThinkPad T61 | t9300 | 3gb | nVidia 140 nvs-quadro (latest driver 296.10) What do you suggest?

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• Turn computer into DAS (Direct Attached Storage)

  - by Damon

  Can we build a direct attached storage by taking a computer/server, adding an HBA, and installing some appropriate software? We would use Debian as a host OS for both the DAS and the server. If so, what software do we use? And do we simply need a HBA for the DAS and the Server? Or do we need more hardware? The goal is to use an older server that does not have enough room for drives but does have ECC memory, server processors, redundant power supplies, dual nics, etc. Then find any boxes, server or not, the key being having enough room for 8-12 drives, fans, etc. and turning them into a DAS; build two of these DAS's and have them connected to the server. Eventually we want to have two servers using DRBD and associated services like heartbeat and pace maker to create an HA setup for our server(s) but that will take a long time to configure since I have no experience with anything related to DRBD (yet) and have a learning curve I have to get past, not to mention the additional cost of more hardware (two servers vs one).

  Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >