Search Results

Search found 5123 results on 205 pages for 'gateway timeout'.

Page 166/205 | < Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >

  • Using a second Wifi Router (in order to use a LAN port)

    - by Sledge81
    Problem: Connecting a TV decoder via Internet. It doesn't have inbuilt wifi so wired LAN is the only option. I bought a second Wifi Router so I could use its LAN port to create a wired internet connection to my decoder. What I want to achieve: The second Wifi Router should basically pick up the signal from the main wifi router. I would then use the LAN port to connect (with a wire) to the TV decoder. In other words have my secondary Wifi Router act as an access point, which will enable me to use a wired LAN connection to the decoder. What i've done so far: Connected the second Wifi Router to my laptop via the LAN ports. Access 192.168.1.1 and went into my second router. 1) SSID set to the same one as the main Wifi Router 2) Tried disabling DHCP and enabling DHCP (with the DNS and default gateway configured the same as the main router). When I check my network connections, I see the LAN connection too but it says 'Not connected to the internet' while the Wifi (main router) shows connected. Can someone please advise on how to use my second Wifi Router to connect to the main Wifi Router (and thus the Internet). Thanks. main wifi router: Zyxel secondary wifi router: TP Link

    Read the article

  • Linux can dual display but windows can't?

    - by Mr_CryptoPrime
    I have two monitors, one that is hdmi-to-dvi and the other vga-to-dvi. I have an AMD HD Radeon 6900 series graphics card installed. I got Ubuntu to display dual monitors, but then I restarted for an update and then Ubuntu wouldn't even boot in recovery mode, it just kept cycling forever...displaying something about "timeout: killing [filepath] [hexadecimal]. So I tried booting into windows (7-professional) and it crashed and displayed this after rebooting: IRQL_NOT_LESS_OR_EQUAL, PAGE_FAULT-IN-NONPAGED-AREA. I went into Bios and reverted to the system defaults and ran system restore and it booted ok, but the dvi-to-dvi monitor would not display. I made sure my drivers were updated and catalyst was updated. Also through research discovered only one is for vga and the other is digital only, so I put the vga-to-dvi in the vga slot and so on. Neither windows or catalyst will detect the dvi-to-dvi montior. Any suggestions? Thanks. EDIT: Found out that booting into Ubuntu with only one monitor (using either monitor with either cable) worked perfectly fine. I could then add another monitor and it displays ok. However, it will, out of the blue, suddenly distort the display. At first I thought the computer crashed, but it is something with the video output from the GPU to the monitor because I pushed the power button and it would refresh every 5secs or so and I could see the "Ubuntu will power down in X seconds", even though it was horribly distorted. Any ideas what's causing this?

    Read the article

  • Anonymizing OpenVPN Allow SSH Access to Internal Server

    - by Lionel
    I'm using an anonymizing VPN, but want SSH access to internal computer. How do I access my internal computer through SSH? When I do ssh 98.123.45.6, the connection times out. IP address from cable provider: 98.123.45.6 Anonymous IP through VPN: 50.1.2.3 Internal computer: 192.168.1.123 When searching around, I found recommendations to either set up iptables rules, routing rules, or to add ListenAddress to sshd_config. Which of these applies to my case? Here is my route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.115.81.1 10.115.81.9 255.255.255.255 UGH 0 0 0 tun0 10.115.81.9 * 255.255.255.255 UH 0 0 0 tun0 50.1.2.3-sta ddwrt 255.255.255.255 UGH 0 0 0 eth0 192.168.1.0 * 255.255.255.0 U 202 0 0 eth0 169.254.0.0 * 255.255.0.0 U 204 0 0 vboxnet0 loopback * 255.0.0.0 U 0 0 0 lo default 10.115.81.9 128.0.0.0 UG 0 0 0 tun0 128.0.0.0 10.115.81.9 128.0.0.0 UG 0 0 0 tun0 default ddwrt 0.0.0.0 UG 202 0 0 eth0

    Read the article

  • SMTP Server setting on Windows 2008 R2

    - by user223298
    I am very very new to this and just trying to configure SMTP virtual server. I have followed a few threads to get it all running, but the mails are not being delivered. What I have done so far - 1) Install SMTP server. 2) SMTP server Properties General Tab - IP address is set to 'All Unassigned'. Access Tab - Authentication is anonymous access. Everything else is left to Default settings. Delivery Tab - Outbound security is anonymous access. In Advance section, entered the domain name in the FQDN field, and localhost in Smart host field. 3) Created an Inbound Rule for SMTP service to allow connections to Port 25. When I try to telnet, everything works up until the point the mail has to be send. Now, the sender's domain is different to the receiver's domain. Not sure if settings have to be changed to allow that? I had set the Relay restrictions on SMTP server, but because I couldn't send the mails, I thought I might as well make it work without the relay first. The error I see while sending the mail is 451 Timeout waiting for client input. I used to get some other error before when I had Relay restrictions on. Can anyone please point me in the right direction? Please let me know if you need more information. Thanks.

    Read the article

  • How to find the reason for a weekly downtime on an Ubuntu web server hosted by AWS?

    - by IceSheep
    We started monitoring our web server using Pingdom and found out that we have a downtime of a few minutes every Sunday at 0:00 UTC. The test runs every minute and checks if a successful HTTP response (code 200) is returned on port 80. The test fails due to a timeout (no response after 30 seconds). Here's what we've already checked – without success: Since we run our webserver behind a load balancer, I've set the Pingdom test on the load balancer's public DNS and the webserver's public DNS in order to find out if there's a problem with the AWS load balancer – both tests return the same result We set up Munin on our webserver. Everything looked fine even after the failure. Since the last failure lasted only 2 minutes I suppose Munin couldn't capture a potential problem (it only checks every 5 minutes) I have checked /var/log/apache2/error.log and /var/log/syslog for suspicious entries I have checked /etc/cron.weekly and /etc/crontab for suspicious entries I have searched for files created or last-modified during 0:00 and 0:15 using this method: touch -t 201209020000 start touch -t 201209020015 end find / -newer start -and ! -newer end (nothing found) Has anybody experienced a similar problem? Any proposals on how to find the reason for this behavior? It's Ubuntu 10.04 LTS running on an AWS m1.large instance. Thanks!

    Read the article

  • Local traffic through VPN, global traffic through WAN

    - by ikonoma
    I have an issue with my internet connection. I am using VPN (Aventail Client) to access the local resources. When connected to VPN the Internet traffic passes through it, not through my LAN or Wi-Fi network. I would like to change the routing table to use the Wi-Fi adapter of the PC for WAN traffic. I have routing file, which works very well and routes the traffic in this way, but only when I am physically connected to the local network through LAN. But I can't set it to work with the VPN connection, because I have no gateway when I am connected to it. Etc this in bold is missing. What to do? route change 0.0.0.0 mask 0.0.0.0 172.16.76.1 metric 200 if 12 route change 0.0.0.0 mask 0.0.0.0 10.44.2.1 metric 400 if 11 route add 150.251.0.0 mask 255.255.0.0 10.44.2.1 metric 100 if 11 route add 10.0.0.0 mask 255.0.0.0 10.44.2.1 metric 100 if 11 pause

    Read the article

  • Lenovo Thinkpad T430 not booting from HDD if there is a USB modem connected

    - by user93353
    I have a T430 Levono Thinkpad running Win7. I use a ZTE USB modem (something like this) for my internet connection. I usually keep the modem plugged into the USB drive even when the laptop is shutdown or hibernating. This worked fine on my earlier laptops. But with the Lenovo, my laptop doesn't boot if the modem is in the USB drive. It shows the initial character based screen where it gives the Thinkpad message & BIOS details and then waits. If I pull out the modem, it goes ahead. I have disabled USB as a boot option in my BIOS settings, but even then this happens sometimes (but not all the times). Likewise while resuming from hibernation. The USB modem also has drivers & ISP connection client which getting installed the first time you use it on any machine. I have used multiple laptops (HP, DELL, Acer, Gateway) but never faced this problem before. I have friends who use other Thinkpad models but haven't faced this issue. Any resolutions, workarounds for this?

    Read the article

  • One single page showing 3 requests (also printing the headers)

    - by Korcholis
    Someone in my studio designed a webpage some years ago, and now the client decided to change the server (he moved to a Linux Apache server running Gen2 SMP, 64 bits, PHP version 5.3.8, Standard MYSQL version 5). It suddenly started to do weird things. When clicking on a link that requires login, the page redirects you to the login page using header() function in PHP. Curiously, the page shows this: OK The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, [no address given] and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. HTTP/1.1 200 OK Date: Mon, 15 Oct 2012 17:27:32 GMT Server: Apache/2.2.22 (Unix) FrontPage/5.0.2.2635 X-Powered-By: PHP/5.3.8 Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Keep-Alive: timeout=5, max=399 Connection: Keep-Alive Transfer-Encoding: chunked Content-Type: text/html 232c Then the page itself, and then, another header: 0 1f4 OK The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, [no address given] and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. 0 What's most intriguing is that if you refresh the page or hit enter on the url, it loads correctly. I've been checking the logs, and it only blames of an inexisting favicon. I also checked the .htaccess, everything was correct (RewriteBase was / as intended, and the only stuff there is another rule that moves ^en/ requests to request?lang=en. Has anyone faced something like this? Edit: IE doesn't trigger these two headers. This is getting wierder.

    Read the article

  • Trying to diagnose network problem: ping 127.0.0.1 (or any address) results in error code 1

    - by Mnebuerquo
    NIC seems to be working, as windows detects the hardware and has a driver and reports success. DHCP seems to have gotten an ip address, 192.168.1.101. I released and renewed it and it seemed to work normally. I tried ping 127.0.0.1 as first step of testing network configuration. Pinging 127.0.0.1 with 32 bytes of data: PING: transmit failed, error code 1. I read somewhere that net helpmsg [error code] would give a human readable name for the error code. net helpmsg 1 says "Incorrect function" I've tried disabling the firewall and antivirus in McAfee SecurityCenter and I still get the same error. Could the firewall/antivirus be breaking it even if disabled? Broadcom Advanced Control Suite 2 is installed, and its network test passes all tests, including ping 192.168.1.1 which is the default gateway. If I try ping 192.168.1.1 from the command prompt I get the error code 1 again. So does anyone have any theories that would explain this problem? Other tests I should try? Thanks!

    Read the article

  • Xen HVM Windows 2008 network bridge

    - by JavierMartinz
    I have a problem with the Windows Server 2008 guest (hvm). I can't get a network interface running for him. I also have a Debian guest and it's working ok, but I can't do it with the Win2k8 guest. When I started the VM, the machine freezes and I can't connect by ssh to the host. /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 188.165.B.C netmask 255.255.255.0 network 188.165.B.0 broadcast 188.165.255.255 gateway 188.165.B.254 brctl show bridge name bridge id STP enabled interfaces eth0 8000.e840f20acc28 no peth0 /etc/xen/xend-config.sxp ... (vif-script vif-bridge) (network-script 'network-bridge') ... /etc/xen/win2k8.cfg # Networking # vif = [ 'ip=5.39.F.G,mac=yy:yy:yy:yy:yy:yy,type=ioemu,bridge=eth0' ] /etc/xen/debian.cfg # Networking # vif = [ 'ip=178.33.D.E,mac=xx:xx:xx:xx:xx:xx' ] As you can see, in the Debian guest I only have to specify an IP address and a MAC. But if I put that in the Win2k8 guest, the machine does not start. I am using Xen 4.0

    Read the article

  • What ports, besides 80, need to be available to send (only send) email using phpmailer to gmail over SSL?

    - by Wobblefoot
    Using phpmailer I keep getting a 110 timeout and "Unable to connect to host" when sending email from my web server. The authentication details are right and they work on another server I have (login, pwd, ports etc and gmail acct set up for SSL connections on 465), but it's failing on my new server. FIREWALL: I allow related/established, port 80 and a port for SSH on INPUT, then this on OUTPUT: 7906 474K DROP tcp -- any any anywhere anywhere tcp dpt:smtp 0 0 ACCEPT tcp -- any any localhost.localdomain yw-in-f109.1e100.net tcp dpt:submission 0 0 ACCEPT tcp -- any any localhost.localdomain gx-in-f109.1e100.net tcp dpt:ssmtp 0 0 DROP tcp -- any any anywhere anywhere tcp dpt:submission 9 540 DROP tcp -- any any anywhere anywhere tcp dpt:ssmtp This output chain works on my other server and disabling it doesn't get mail delivered either. WEB SERVER: Varnish (80) Nginx (8088) Drupal 7 PHP5-FPM APC MySQL All works beautifully, except for outgoing email. What else could it be? I understand phpmailer does NOT require a local MTA or procmail (this is sort of the point - I don't want the security or admin overhead of a full blown MTA on my web server). Am I wrong? Do I need an MTA as well? What local ports and programs are used to authenticate over SSL and route mail using phpmailer? Any ideas at all greatly appreciated - wasted a day on this nonsense already!

    Read the article

  • How to prevent response to who-has requests on virtual eth interface?

    - by user42881
    Hi, we use small embedded X86 linux servers equipped with a single physical ethernet port as a gateway for an IP video surveillance application. Each downstream IP cam is mapped to a separate virtual IP address like this: real eth0 IP address= 192.168.1.1, camera 1 (eth0:1) =192.168.1.61, camera 2 (eth0:2) =192.168.1.62, etc. etc. all on the same eth0 physical port. This approach works well, except that a specific third-party windows video recording application running on a separate PC on the same LAN, automatically pings the virtual IPs looking for unique who-has responses on system startup and, when it gets back the same eth0 MAC address for each virtual interface, freaks out and won't allow us to subsequently manually enter those addresses. The windows app doesn't mind, tho, if it receives no answer to the who-has ping. My question - how can we either (a) shut off the who-has responses just for the virtual eth0:x interfaces while keeping them for the primary physical eth0 port, or, in the alternative, spoof a valid but different MAC address for each virtual interface? Thanks!

    Read the article

  • OpenVPN / iptables restrict some access

    - by RitonLaJoie
    I want to create an openvpn service on a dedicated server I have, for some friends so that they are able to play online games faster. Is there an easy way to restrict which traffic I allow them with iptables ? It seems iptable is not very easy to maintain and we can easily get kicked out of our own server. Rebooting on a rescue mode every time I would get kicked out because of bad iptable rules would just be a pain. As far as I understand, the tun interface would be providing the access. Which kind of rule in iptables would I have to implement to restrict their access to only 1 ip ? Also, I don't want this vpn to be the default gateway for all the traffic. I guess I should go with the option of pushing a route to the clients so that they connect to the IP of the game server through the VPN and use their regular routes through their ISP for all the other traffic ? As a side not, it seems Openvpn AS is not very robust. Is there some other (commercial is ok) product that would give me the same administration options through a web interface ? Is Webmin the only other solution ? Thanks !

    Read the article

  • SSL configuration issue. SSL/IIS7 not loading all scripts/CSS on user's first visit

    - by Chris
    Hi all, Hopefully this isnt a tricky one. I've got a web app that doesn't load all javascript/css/images on the first visit. Second visit is fine. After approximately 2 minutes of inactivity the problem reoccurs. These problems only started occuring after the customer requested SSL be applied to the application. Ajax requests stop working after 2 minutes of activity despite a successful page load of all javascript elements. Application timeout is 30 minutes - like I said, everything was fine before SSL was applied. All javascript and CSS files use absolute URLS - e.g https://blablabla There appears to be no pattern as to why certain files arent loaded. The firebug Net output shows the status for the failed elements as 'Aborted'. For example, site.css and nav.css are in the same folder, are declared after each other in the head tag yet one is loaded and the other is not. Both will load fine after refreshing the page (unless roughly two minutes have passed). An Ajax request also shows as aborted after two minutes. However, if i do the request again the Ajax request will succeed. Almost as if the first request woke something up. None of these problems occur in Chrome Any ideas? FYI this is a .Net 4 C# MVC app running under IIS7 but I'm not sure its relevant since it works in Chrome. Everything worked fine before SSL was applied. Originally posted on stackoverflow but recommended to list here. Can provide additional details if necessary.

    Read the article

  • Windows 7 computer apparently connected to working wireless network but can't access router page or internet

    - by Hemmer
    I can consistently connect successfully to both the router and the internet using both my phone and two different computers which strongly suggests that the issue is at the desktop end. Only my Windows 7 desktop machine has stopped getting internet connectivity. It manages to connect to the router's network using the Windows 7 wireless dialog, but can't access either the router configuration page (192.168.1.1) or the internet in general once connected. The strange thing is the wireless network icon in the notification bar shows a full strength signal, sometimes with the yellow warning triangle. The output of ipconfig /all is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11g Network Adapter Physical Address. . . . . . . . . : 00-12-17-94-98-90 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.102(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 08 June 2011 10:32:16 Lease Expires . . . . . . . . . . : 08 June 2011 12:32:16 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 194.168.4.100 194.168.8.100 NetBIOS over Tcpip. . . . . . . . : Enabled I've tried renewing DCHP settings disabling IPv6 resetting TCP stack uninstalling and reinstalling WLAN card drivers I've not installed anything new or made any changes to my knowledge, this just happened out of the blue. The only possible change is my friend connected his macbook to the network, but that has gone now and shouldn't have any lasting effects? TCP/IPv4 is set to automatically find an IP address. Antivirus is MSE (up to date) and doesn't detect anything unusual. Any ideas where to go next? Any help is greatly appreciated. For reference, the results of ipconfig /all on one of the working computers is: Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11g Network Adapter Physical Address. . . . . . . . . : 00-16-CF-67-E5-97 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 194.168.4.100 194.168.8.100 Lease Obtained. . . . . . . . . . : 08 June 2011 10:26:38 Lease Expires . . . . . . . . . . : 08 June 2011 12:26:38 UPDATE: Still not working, but I've managed to find a temporary workaround by tethering my Android phone, effectively becoming a new wifi adapter. Will be moving to a new flat so will test if it is a network specific thing - maybe the card has got damaged somehow? Also will see if the card is working with Linux soon.

    Read the article

  • Using iptables to make a VPN router

    - by lost_in_the_sauce
    I am attempting to make a VPN connection to a third party VPN site, then forward traffic from my internal computers (ssh and ping for now) out to the VPN site using IPTables. 3rd Party <- (tun0/eth0)Linux VPN Box(eth1) <- Windows7TestBox I am running on CentOS 6.3 Linux and have two network connections eth0-public eth1-private. I am running vpnc-0.5.3-4 which is currently connecting to my destination. When I connect I am able to ping the destination IPAddresses but that is as far as I can get. ping -I tun0 10.1.33.26 success ping -I eth0 10.1.33.26 fail ping -I eth1 10.1.33.26 fail I have my private network Windows 7 test box set up to have the eth1 (private) network of my VPN Server as its gateway and can ping him fine. I need IPTables to send the Windows 7 traffic out the VPN tunnel. I have tried for a few days many different IPTables configurations from this site and others, either the other examples are too simple or overly complicated. The only thing this server is doing is connecting to the VPN and forwarding all traffic. So we can "flush" everything and start from scratch here. It is a blank slate. #!/bin/bash echo "Define variables" ipt="/sbin/iptables" echo "Zero out all counters" $ipt -Z $ipt -t nat -Z $ipt -t mangle -Z echo "Flush all active rules, delete all chains" $ipt -F $ipt -X $ipt -t nat -F $ipt -t nat -X $ipt -t mangle -F $ipt -t mangle -X $ipt -P INPUT ACCEPT $ipt -P FORWARD ACCEPT $ipt -P OUTPUT ACCEPT $ipt -t nat -A POSTROUTING -o tun0 -j MASQUERADE $ipt -A FORWARD -i eth1 -o eth0 -j ACCEPT $ipt -A FORWARD -i eth0 -o eth1 -j ACCEPT $ipt -A FORWARD -i eth0 -o tun0 -j ACCEPT $ipt -A FORWARD -i tun0 -o eth0 -j ACCEPT Again I have done many variations of the above and many other rules from other posts but haven't been able to move forward. It seems like such a simple task, and yet....

    Read the article

  • Formatting a former RAID 0 drive through USB

    - by EXC
    I'll try to be as specific as possible here: I was using two Hitachi 2.5" 500 gb HDDs in my Gateway P-7805u laptop in a RAID 0 configuration. The array was causing the laptop to run extremely hot, however, so I removed them and deleted the RAID array through Intel Matrix HDD manager. I did a clean install of Windows 7 on the original 320 gb HDD that came with the laptop. I never did format the original RAID array HDDs before taking them out of the computer. Now, I am attempting to format the Hitachi 500 gb RAID array HDDs externally through a USB external enclosure. The external HDD drivers install on my clean install OS, but when I go into 'My Computer' there is no external drive available. I cannot format in CMD Prompt because my computer will not designate a drive letter to the external HDD. The drivers install and the HDD is recognized as a Hitachi external drive, but nothing seems to show up in my computer window. I need to know if there is a way to format these drives to NTFS externally.

    Read the article

  • How to route 1 VPN through another on OS X?

    - by Eeep
    Hi everyone. Thanks a lot for your help! I've been tinkering with this for a while and have read many posts along with Googling for help, but my knowledge of TCP/IP is really weak... I have access to two different VPN servers. 1 Is set up in Network Settings and connects through PPP 2 Is set up through Tunnelblick and uses OpenVPN. I can connect to either tunnel #1 or tunnel #2, but not both one after the other... One of my major to-do's this year is study TCP/IP, but for now, would you be super-helpful and help me fix this really clearly? I have no experience with routing, DNS, gateways or any of that. If you tell me, "Set your gateway to XXX.XXX.XX.XXX" can you specify how I get that IP, off of what interface so I don't get messed up? I can figure out the terminal just fine if you let me know what to type, and I WILL read the man pages on everything you help me with. Thanks a million!

    Read the article

  • Where does Firefox store cerificates and how to delete one?

    - by majid4466
    Hi all, The root cause of my problem is not known to me, whatever it is, I experience frequent DNS failures. When it happens I cannot browse to my Gmail inbox. I use two DNS settings. One is the public DNS server offered by OpenDNS, and the other is Google's free DNS server. When this happens I switch from the active setting to the other one and the problem goes away. But there is a side effect to this. When browsing to Gmail fails to load, after switching the DNS I receive an error saying the security certificate the site uses is only valid for OpenDNS. This my wild guess at what is going on: 1. OpenDNS fails to resolve mail.google.com to its IP, 2. My ISP sends me a page showing search results for 'mail.google.com' 3. Since I have received some sort of page instead of a timeout, the browser, mistakenly, binds the certificate it has cached for 'mail.google.com' to the new domain. This search page is not served by https so not exception is thrown by the wrong binding 4. After switching the DNS, the domain is correctly resolved to Gmail server's IP and since his is on https the handshake is triggered. 5. Now, because of the wrong binding, which passed quietly as no handshake was involved, I receive the error saying the certificate used by 'mail.google.com' is only good for openDNS I don't know much about DNS, less about https and the process of establishing a secure connection. How correct is my explanation? How can I delete the wrong association and/or the certificate? Thanks for listening. P. S. The problem goes away by itself, but sometimes it takes several hours before Gmail works again.

    Read the article

  • Where does Firefox store cerificates and how to delete one?

    - by majid4466
    Hi all, The root cause of my problem is not known to me, whatever it is, I experience frequent DNS failures. When it happens I cannot browse to my Gmail inbox. I use two DNS settings. One is the public DNS server offered by OpenDNS, and the other is Google's free DNS server. When this happens I switch from the active setting to the other one and the problem goes away. But there is a side effect to this. When browsing to Gmail fails to load, after switching the DNS I receive an error saying the security certificate the site uses is only valid for OpenDNS. This my wild guess at what is going on: OpenDNS fails to resolve mail.google.com to its IP, My ISP sends me a page showing search results for 'mail.google.com' Since I have received some sort of page instead of a timeout, the browser, mistakenly, binds the certificate it has cached for 'mail.google.com' to the new domain. This search page is not served by https so not exception is thrown by the wrong binding After switching the DNS, the domain is correctly resolved to Gmail server's IP and since his is on https the handshake is triggered. Now, because of the wrong binding, which passed quietly as no handshake was involved, I receive the error saying the certificate used by 'mail.google.com' is only good for openDNS I don't know much about DNS, less about https and the process of establishing a secure connection. How correct is my explanation? How can I delete the wrong association and/or the certificate? Thanks for listening. P. S. The problem goes away by itself, but sometimes it takes several hours before Gmail works again.

    Read the article

  • Iptables state tracking

    - by complexgeek
    Hi there. I've just taken over administration of a fairly complex firewall ruleset for a firewall box running Fedora Core 12, and there's one thing about it that is puzzling me. When I run nmap on the gateway from outside the network, I see all the expected services, but also sunrpc on port 111. The INPUT chain has DEFAULT DROP set, and there is no rule allowing port 111. As best I can tell (watching the packet counters before/during/after the scan) it's being allowed by the rule: "-m state --state RELATED,ESTABLISHED -j ACCEPT" but I don't understand why a brand new TCP connection would be considered RELATED or ESTABLISHED. Any suggestions would be greatly appreciated. EDIT: Conntrack modules: nf_conntrack_netlink 14925 0 nfnetlink 3479 1 nf_conntrack_netlink nf_conntrack_irc 5206 1 nf_nat_irc nf_conntrack_proto_udplite 3138 0 nf_conntrack_h323 62110 1 nf_nat_h323 nf_conntrack_proto_dccp 6878 0 nf_conntrack_sip 16921 1 nf_nat_sip nf_conntrack_proto_sctp 11131 0 nf_conntrack_pptp 10673 1 nf_nat_pptp nf_conntrack_sane 5458 0 nf_conntrack_proto_gre 6574 1 nf_conntrack_pptp nf_conntrack_amanda 2796 1 nf_nat_amanda nf_conntrack_ftp 11741 1 nf_nat_ftp nf_conntrack_tftp 4665 1 nf_nat_tftp nf_conntrack_netbios_ns 1534 0 nf_conntrack_ipv6 18504 2 ipv6 279399 40 ip6t_REJECT,nf_conntrack_ipv6 INPUT chain on the filter table: -A INPUT -s 192.168.200.10/32 -p tcp -m tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT -A INPUT -s 127.0.0.0/8 -i lo -j ACCEPT -A INPUT -p udp -m udp --sport 67:68 --dport 67:68 -j ACCEPT -A INPUT -d 192.168.200.5/32 -i eth0 -j ACCEPT -A INPUT -d 192.168.1.2/32 -i eth0 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p tcp -m multiport --dports 22,80,443 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p tcp -m multiport --sports 22,25,80,443 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m udp --dport 1194 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m udp --sport 1194 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m multiport --sports 53,123 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p icmp -m icmp --icmp-type 8 -j ACCEPT -A INPUT -i eth0 -m state --state NEW -j ACCEPT -A INPUT -d {public_ip}/32 -m state --state NEW -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT eth0 is connected to the internal network, eth3 is connected to an ADSL modem in bridge mode, ppp0 is the WAN connection tunneled over eth3.

    Read the article

  • NoClassDefFoundError and Netty

    - by Dmytro Leonenko
    Hi. First to say I'm n00b in Java. I can understand most concepts but in my situation I want somebody to help me. I'm using JBoss Netty to handle simple http request and using MemCachedClient check existence of client ip in memcached. import org.jboss.netty.channel.ChannelHandler; import static org.jboss.netty.handler.codec.http.HttpHeaders.*; import static org.jboss.netty.handler.codec.http.HttpHeaders.Names.*; import static org.jboss.netty.handler.codec.http.HttpResponseStatus.*; import static org.jboss.netty.handler.codec.http.HttpVersion.*; import com.danga.MemCached.*; import java.util.List; import java.util.Map; import java.util.Map.Entry; import java.util.Set; import org.jboss.netty.buffer.ChannelBuffer; import org.jboss.netty.buffer.ChannelBuffers; import org.jboss.netty.channel.ChannelFuture; import org.jboss.netty.channel.ChannelFutureListener; import org.jboss.netty.channel.ChannelHandlerContext; import org.jboss.netty.channel.ExceptionEvent; import org.jboss.netty.channel.MessageEvent; import org.jboss.netty.channel.SimpleChannelUpstreamHandler; import org.jboss.netty.handler.codec.http.Cookie; import org.jboss.netty.handler.codec.http.CookieDecoder; import org.jboss.netty.handler.codec.http.CookieEncoder; import org.jboss.netty.handler.codec.http.DefaultHttpResponse; import org.jboss.netty.handler.codec.http.HttpChunk; import org.jboss.netty.handler.codec.http.HttpChunkTrailer; import org.jboss.netty.handler.codec.http.HttpRequest; import org.jboss.netty.handler.codec.http.HttpResponse; import org.jboss.netty.handler.codec.http.HttpResponseStatus; import org.jboss.netty.handler.codec.http.QueryStringDecoder; import org.jboss.netty.util.CharsetUtil; /** * @author <a href="http://www.jboss.org/netty/">The Netty Project</a> * @author Andy Taylor ([email protected]) * @author <a href="http://gleamynode.net/">Trustin Lee</a> * * @version $Rev: 2368 $, $Date: 2010-10-18 17:19:03 +0900 (Mon, 18 Oct 2010) $ */ @SuppressWarnings({"ALL"}) public class HttpRequestHandler extends SimpleChannelUpstreamHandler { private HttpRequest request; private boolean readingChunks; /** Buffer that stores the response content */ private final StringBuilder buf = new StringBuilder(); protected MemCachedClient mcc = new MemCachedClient(); private static SockIOPool poolInstance = null; static { // server list and weights String[] servers = { "lcalhost:11211" }; //Integer[] weights = { 3, 3, 2 }; Integer[] weights = {1}; // grab an instance of our connection pool SockIOPool pool = SockIOPool.getInstance(); // set the servers and the weights pool.setServers(servers); pool.setWeights(weights); // set some basic pool settings // 5 initial, 5 min, and 250 max conns // and set the max idle time for a conn // to 6 hours pool.setInitConn(5); pool.setMinConn(5); pool.setMaxConn(250); pool.setMaxIdle(21600000); //1000 * 60 * 60 * 6 // set the sleep for the maint thread // it will wake up every x seconds and // maintain the pool size pool.setMaintSleep(30); // set some TCP settings // disable nagle // set the read timeout to 3 secs // and don't set a connect timeout pool.setNagle(false); pool.setSocketTO(3000); pool.setSocketConnectTO(0); // initialize the connection pool pool.initialize(); // lets set some compression on for the client // compress anything larger than 64k //mcc.setCompressEnable(true); //mcc.setCompressThreshold(64 * 1024); } @Override public void messageReceived(ChannelHandlerContext ctx, MessageEvent e) throws Exception { HttpRequest request = this.request = (HttpRequest) e.getMessage(); if(mcc.get(request.getHeader("X-Real-Ip")) != null) { HttpResponse response = new DefaultHttpResponse(HTTP_1_1, OK); response.setHeader("X-Accel-Redirect", request.getUri()); ctx.getChannel().write(response).addListener(ChannelFutureListener.CLOSE); } else { sendError(ctx, NOT_FOUND); } } private void writeResponse(MessageEvent e) { // Decide whether to close the connection or not. boolean keepAlive = isKeepAlive(request); // Build the response object. HttpResponse response = new DefaultHttpResponse(HTTP_1_1, OK); response.setContent(ChannelBuffers.copiedBuffer(buf.toString(), CharsetUtil.UTF_8)); response.setHeader(CONTENT_TYPE, "text/plain; charset=UTF-8"); if (keepAlive) { // Add 'Content-Length' header only for a keep-alive connection. response.setHeader(CONTENT_LENGTH, response.getContent().readableBytes()); } // Encode the cookie. String cookieString = request.getHeader(COOKIE); if (cookieString != null) { CookieDecoder cookieDecoder = new CookieDecoder(); Set<Cookie> cookies = cookieDecoder.decode(cookieString); if(!cookies.isEmpty()) { // Reset the cookies if necessary. CookieEncoder cookieEncoder = new CookieEncoder(true); for (Cookie cookie : cookies) { cookieEncoder.addCookie(cookie); } response.addHeader(SET_COOKIE, cookieEncoder.encode()); } } // Write the response. ChannelFuture future = e.getChannel().write(response); // Close the non-keep-alive connection after the write operation is done. if (!keepAlive) { future.addListener(ChannelFutureListener.CLOSE); } } @Override public void exceptionCaught(ChannelHandlerContext ctx, ExceptionEvent e) throws Exception { e.getCause().printStackTrace(); e.getChannel().close(); } private void sendError(ChannelHandlerContext ctx, HttpResponseStatus status) { HttpResponse response = new DefaultHttpResponse(HTTP_1_1, status); response.setHeader(CONTENT_TYPE, "text/plain; charset=UTF-8"); response.setContent(ChannelBuffers.copiedBuffer( "Failure: " + status.toString() + "\r\n", CharsetUtil.UTF_8)); // Close the connection as soon as the error message is sent. ctx.getChannel().write(response).addListener(ChannelFutureListener.CLOSE); } } When I try to send request like http://127.0.0.1:8090/1/2/3 I'm getting java.lang.NoClassDefFoundError: com/danga/MemCached/MemCachedClient at httpClientValidator.server.HttpRequestHandler.<clinit>(HttpRequestHandler.java:66) I believe it's not related to classpath. May be it's related to context in which mcc doesn't exist. Any help appreciated EDIT: Original code http://docs.jboss.org/netty/3.2/xref/org/jboss/netty/example/http/snoop/package-summary.html I've modified some parts to fit my needs.

    Read the article

  • sage pay testing error

    - by Phil Jackson
    Hi, im trying to test my sage pay integration but to no avail. Here is my code: private function init_sagepay(){ extract( static::$post ); $settings = global_data::get_settings(); $strConnectTo = "TTEST"; $strVirtualDir = "VSPForm-Kit"; $strYourSiteFQDN = global_data::get_web_root(); $strVSPVendorName = $settings->sagepay_vendor; $strEncryptionPassword = "z5p************"; $strCurrency = static::$currency; $strVendorEMail = $settings->sagepay_email; $strTransactionType = "PAYMENT"; $strProtocol = "2.23"; if ( $strConnectTo == "LIVE" ) $strPurchaseURL = "https://live.sagepay.com/gateway/service/vspform-register.vsp"; elseif ( $strConnectTo == "TEST" ) $strPurchaseURL = "https://test.sagepay.com/gateway/service/vspform-register.vsp"; elseif( $strConnectTo == 'TTEST' ) $strPurchaseURL = 'https://test.sagepay.com/Simulator/VSPServerGateway.asp?Service=VendorRegisterTx'; else $strPurchaseURL = "https://test.sagepay.com/Simulator/VSPDirectGateway.asp"; $details = self::get_member_details(); $thisOrderDeteails = 'order details...'; $ThisVendorTxCode = 'fdsdgfd'; $ThisAmount = $total; $ThisCurrency = static::$currency; $ThisDescription = "description..."; $ThisCustomerEmail = $details->email; $ThisCustomerName = $details->first_name . " " . $details->last_name; $ThisVendorEmail = $strVendorEMail; $ThisApplyAVSCV2 = 1; $ThisApply3DSecure = 1; $ThisDeliveryAddress = $address_line_1 . ", " . $address_line_2 . ", " . $address_line_3 . ", " . $address_line_4 . ", " . $country; $ThisDeliveryPostCode = $postcode; $address_full = $ThisDeliveryAddress . ' ' . $ThisDeliveryPostCode; $ThisBillingAddress = $details->address_line_1 . ", " . $details->address_line_2 . ", " . $details->address_line_3 . ", " . $details->address_line_4 . ", " . $details->country; $ThisBillingPostCode = $details->postcode; // new 2.22 fields $ThisContactNumber = $details->home_number; $ThisContactFax = $details->fax_number; $ThisAllowGiftAid = ''; //$ThisApplyAVSCV2 = $_REQUEST[ 'ApplyAVSCV2' ]; //$ThisApply3DSecure = $_REQUEST[ 'Apply3DSecure' ]; $ShoppingBasket = array(); $x = 0; foreach( $items as $item ) { preg_match( "#^\[([^\]]+)\]\[([^\]]+)\]$#is", $item, $match ); $item = $match[1]; $price = $match[2]; $ShoppingBasket[$x][0] = $item; $ShoppingBasket[$x][1] = $price; $x++; } if ( isset( $ShoppingBasket ) ) { $ThisShoppingBasket = $ShoppingBasket; }else{ $ThisShoppingBasket = "OFF"; } //** Build the crypt string plaintext ** $stuff = "VendorTxCode=" . $ThisVendorTxCode . "&"; $stuff .= "Amount=" . $ThisAmount . "&"; $stuff .= "Currency=" . $ThisCurrency . "&"; $stuff .= "Description=" . $ThisDescription . "&"; $stuff .= "SuccessURL=" . $strYourSiteFQDN . "completed.php&"; $stuff .= "FailureURL=" . $strYourSiteFQDN . "notcompleted.php&"; if ($ThisCustomerEmail) { $stuff .= "CustomerEmail=" . $ThisCustomerEmail . "&"; } if ($ThisVendorEmail) { $stuff .= "VendorEmail=" . $ThisVendorEmail . "&"; } if ($ThisCustomerName) { $stuff .= "CustomerName=" . $ThisCustomerName . "&"; } if ($ThisDeliveryAddress) { $stuff .= "DeliveryAddress=" . $ThisDeliveryAddress . "&"; } if ($ThisDeliveryPostCode) { $stuff .= "DeliveryPostCode=" . $ThisDeliveryPostCode . "&"; } if ($ThisBillingAddress) { $stuff .= "BillingAddress=" . $ThisBillingAddress . "&"; } if ($ThisBillingPostCode) { $stuff .= "BillingPostCode=" . $ThisBillingPostCode . "&"; } // new 2.22 fields if ($ThisContactNumber) { $stuff .= "ContactNumber=" . $ThisContactNumber . "&"; } if ($ThisContactFax) { $stuff .= "ContactFax=" . $ThisContactFax . "&"; } if ($ThisAllowGiftAid) { $stuff .= "AllowGiftAid=" . $ThisAllowGiftAid . "&"; } if ($ThisApplyAVSCV2) { $stuff .= "ApplyAVSCV2=" . $ThisApplyAVSCV2 . "&"; } if ($ThisApply3DSecure) { $stuff .= "Apply3DSecure=" . $ThisApply3DSecure . "&"; } //echo $stuff; if ($ThisShoppingBasket=="ON") { $stuff .= "Basket=3:Sony SV-234 DVD Player:1:£170.20:£29.79:£199.99:£199.99:The Fast and The Furious Region 2 DVD:2:£17.01:£2.98:£19.99:£39.98:Delivery:1:£4.99:----:£4.99:£4.99&"; } $stuff .= "EMailMessage=For an update on the status of your order please email us at $ThisVendorEmail"; $crypt = self::base64Encode( self::SimpleXor( $stuff,$strEncryptionPassword ) ); $ThisDate = date('U'); ob_start(); ?> <form action="<?php echo $strPurchaseURL; ?>" method="post" id="sageForm" name="form1"> <input TYPE="hidden" name="VPSProtocol" value="<?php echo $strProtocol; ?>"> <input TYPE="hidden" name="TxType" value="<?php echo $strTransactionType; ?>"> <input TYPE="hidden" name="Vendor" value="<?php echo $strVSPVendorName; ?>"> <input TYPE="hidden" name="Crypt" value="<?php echo $crypt; ?>"> <input name="sbbutton" type="submit" value="Checkout" class="wpcf7-submit"> </form> <?php return ob_get_clean(); } when using "TEST" im getting an error: Status Detail: 5005 : The Vendor configuration is missing or invalid when using "TTEST" im getting an error: VPSProtocol=2.23 Status=INVALID StatusDetail=The VendorTxCode you supplied is an invalid length. VendorTxCodes should be between 1 to 40 characters long I cannot seem to figure this out at all. If anyone has any ideas it would be greatfuly appreciated. EDIT: $stuff echos out: VendorTxCode=fdsdgfd&Amount=45.60&Currency=GBP&Description=description...&SuccessURL=http://localhost/ecom_framework/&FailureURL=http://localhost/ecom_framework/&[email protected]&[email protected]&CustomerName=Luke Snowden&DeliveryAddress=mansfield, nottinghamshire, mansfield, nottinghamshire, United Kingdom&DeliveryPostCode=ng19 8pw&BillingAddress=mansfield, nottinghamshire, mansfield, nottinghamshire, United Kingdom&BillingPostCode=ng19 8pw&ContactNumber=0165656567&ApplyAVSCV2=1&Apply3DSecure=1&Basket=3:Blue Hat - black :2:£2£:0.00:£4.00:Blue Hat - brown :3:£3£:0.00:£9.00:Blue Hat - grey :4:£4£:0.00:£16.00:Delivery:1:£4.99EMailMessage=For an update on the status of your order please email us at [email protected]

    Read the article

  • whats wrong with the following code

    - by giri
    Hi i am trying to send sms to my mobile using java.When I run the application I am getting the the follwing error. package HelloWorld; import java.io.*; import java.util.BitSet; import javax.comm.*; import java.lang.*; public class SerialToGsm { InputStream in; OutputStream out; String lastIndexRead; String senderNum; String smsMsg; SerialToGsm(String porta) { try { // CommPortIdentifier portId = CommPortIdentifier.getPortIdentifier("serial0"); CommPortIdentifier portId = CommPortIdentifier.getPortIdentifier(porta); SerialPort sp = (SerialPort)portId.open("Sms_GSM", 0); sp.setSerialPortParams(9600, SerialPort.DATABITS_8, SerialPort.STOPBITS_1, SerialPort.PARITY_NONE); sp.setFlowControlMode(sp.FLOWCONTROL_NONE); in = sp.getInputStream(); out = sp.getOutputStream(); // modem reset sendAndRecv("+++AT", 30); // delay for 20 sec/10 sendAndRecv("AT&F", 30); sendAndRecv("ATE0", 30); // echo off sendAndRecv("AT +CMEE=1", 30); // verbose error messages sendAndRecv("AT+CMGF=0", 70); // set pdu mode // sendAndRecv("AT V1E0S0=0&D2&C1", 1000000); } catch (Exception e) { System.out.println("Exception " + e); System.exit(1); } } private String sendAndRecv(String s, int timeout) { try { // clean serial port input buffer in.skip(in.available()); System.out.println("=> " + s); s = s + "\r"; // add CR out.write(s.getBytes()); out.flush(); String strIn = new String(); for (int i = 0; i < timeout; i++){ int numChars = in.available(); if (numChars > 0) { byte[] bb = new byte[numChars]; in.read(bb,0,numChars); strIn += new String(bb); } // start exit conditions // --------------------- if (strIn.indexOf(">\r\n") != -1) { break; } if (strIn.indexOf("OK\r\n") != -1){ break; } if (strIn.indexOf("ERROR") != -1) { // if find 'error' wait for CR+LF if (strIn.indexOf("\r\n",strIn.indexOf("ERROR") + 1) != -1) { break; } } Thread.sleep(100); // delay 1/10 sec } System.out.println("<= " + strIn); if (strIn.length() == 0) { return "ERROR: len 0"; } return strIn; } catch (Exception e) { System.out.println("send e recv Exception " + e); return "ERROR: send e recv Exception"; } } public String sendSms (String numToSend, String whatToSend) { ComputSmsData sms = new ComputSmsData(); sms.setAsciiTxt(whatToSend); sms.setTelNum(numToSend); // sms.setSMSCTelNum("+393359609600"); // SC fixed String s = new String(); s = sendAndRecv("AT+CMGS=" + (sms.getCompletePduData().length() / 2) + "\r", 30); // System.out.println("==> AT+CMGS=" + (sms.getCompletePduData().length() / 2)); // System.out.println("<== " + s); if (s.indexOf(">") != -1) { // s = sendAndRecv(sms.getSMSCPduData() + sms.getCompletePduData() + "\u001A"); // usefull one day? // System.out.println("Inviero questo >>>> " + sms.getCompletePduData()); // if this sintax won't work try remove 00 prefix s = sendAndRecv("00" + sms.getCompletePduData() + "\u001A", 150); // System.out.println("<== " + s); return s; } else { return "ERROR"; } } // used to reset message data private void resetGsmObj() { lastIndexRead = null; senderNum = null; smsMsg = null; } public String checkSms (){ String str = new String(); String strGsm = new String(); strGsm = sendAndRecv("AT+CMGL=0", 30); // list unread msg and sign them as read // if answer contain ERROR then ERROR if (strGsm.indexOf("ERROR") != -1) { resetGsmObj(); return strGsm; // error } strGsm = sendAndRecv("AT+CMGL=1", 30); // list read msg // if answer contain ERROR then ERROR if (strGsm.indexOf("ERROR") != -1) { resetGsmObj(); return strGsm; // error } // evaluate message index if (strGsm.indexOf(':') <= 0) { resetGsmObj(); return ("ERROR unexpected answer"); } str = strGsm.substring(strGsm.indexOf(':') + 1,strGsm.indexOf(',')); str = str.trim(); // remove white spaces // System.out.println("Index: " + str); lastIndexRead = str; // find message string // ------------------- // look for start point (search \r, then skip \n, add and one more for right char int startPoint = strGsm.indexOf("\r",(strGsm.indexOf(":") + 1)) + 2; int endPoint = strGsm.indexOf("\r",startPoint + 1); if (endPoint == -1) { // only one message endPoint = strGsm.length(); } // extract string str = strGsm.substring(startPoint, endPoint); System.out.println("String to be decoded :" + str); ComputSmsData sms = new ComputSmsData(); sms.setRcvdPdu(str); // SMSCNum = new String(sms.getRcvdPduSMSC()); senderNum = new String(sms.getRcvdSenderNumber()); smsMsg = new String(sms.getRcvdPduTxt()); System.out.println("SMSC number: " + sms.getRcvdPduSMSC()); System.out.println("Sender number: " + sms.getRcvdSenderNumber()); System.out.println("Message: " + sms.getRcvdPduTxt()); return "OK"; } public String readSmsSender() { return senderNum; } public String readSms() { return smsMsg; } public String delSms() { if (lastIndexRead != "") { return sendAndRecv("AT+CMGD=" + lastIndexRead, 30); } return ("ERROR"); } } ERROR: Error loading SolarisSerial: java.lang.UnsatisfiedLinkError: no SolarisSerialParallel in java.library.path Caught java.lang.UnsatisfiedLinkError: com.sun.comm.SolarisDriver.readRegistrySerial(Ljava/util/Vector;Ljava/lang/String;)I while loading driver com.sun.comm.SolarisDriver Exception javax.comm.NoSuchPortException

    Read the article

  • No bean named 'springSecurityFilterChain' is defined

    - by michaeljackson4ever
    When configs are loaded, I get the error SEVERE: Exception starting filter springSecurityFilterChain org.springframework.beans.factory.NoSuchBeanDefinitionException: No bean named 'springSecurityFilterChain' is defined My sec-config: <http use-expressions="true" access-denied-page="/error/casfailed.html" entry-point-ref="headerAuthenticationEntryPoint"> <intercept-url pattern="/" access="permitAll"/> <!-- <intercept-url pattern="/index.html" access="permitAll"/> --> <intercept-url pattern="/index.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/history.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/absence.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/search.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/employees.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/employee.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/contract.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/myforms.html" access="hasAnyRole('HLO','OPISK')"/> <intercept-url pattern="/vacationmsg.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/redirect.jsp" filters="none" /> <intercept-url pattern="/error/**" filters="none" /> <intercept-url pattern="/layout/**" filters="none" /> <intercept-url pattern="/js/**" filters="none" /> <intercept-url pattern="/**" access="isAuthenticated()" /> <!-- session-management invalid-session-url="/absence.html"/ --> <!-- logout logout-success-url="/logout.html"/ --> <custom-filter ref="ssoHeaderAuthenticationFilter" before="CAS_FILTER"/> <!-- CAS_FILTER ??? --> </http> <authentication-manager alias="authenticationManager"> <authentication-provider ref="doNothingAuthenticationProvider"/> </authentication-manager> <beans:bean id="doNothingAuthenticationProvider" class="com.nixu.security.sso.web.DoNothingAuthenticationProvider"/> <beans:bean id="ssoHeaderAuthenticationFilter" class="com.nixu.security.sso.web.HeaderAuthenticationFilter"> <beans:property name="groups"> <beans:map> <beans:entry key="cn=lake,ou=confluence,dc=utu,dc=fi" value="ROLE_ADMIN"/> </beans:map> </beans:property> </beans:bean> <beans:bean id="headerAuthenticationEntryPoint" class="com.nixu.security.sso.web.HeaderAuthenticationEntryPoint"/> And web.xml <context-param> <param-name>contextConfigLocation</param-name> <param-value> /WEB-INF/applicationContext.xml /WEB-INF/sec-config.xml /WEB-INF/idm-config.xml /WEB-INF/ldap-config.xml </param-value> </context-param> <display-name>KeyCard</display-name> <context-param> <param-name>webAppRootKey</param-name> <param-value>KeyCardAppRoot</param-value> </context-param> <context-param> <param-name>log4jConfigLocation</param-name> <param-value>/WEB-INF/log4j.properties</param-value> </context-param> <!-- Reads request input using UTF-8 encoding --> <filter> <filter-name>characterEncodingFilter</filter-name> <filter-class>org.springframework.web.filter.CharacterEncodingFilter</filter-class> <init-param> <param-name>encoding</param-name> <param-value>UTF-8</param-value> </init-param> <init-param> <param-name>forceEncoding</param-name> <param-value>true</param-value> </init-param> </filter> <filter> <filter-name>springSecurityFilterChain</filter-name> <filter-class>org.springframework.web.filter.DelegatingFilterProxy</filter-class> </filter> <filter-mapping> <filter-name>characterEncodingFilter</filter-name> <url-pattern>/*</url-pattern> </filter-mapping> <filter-mapping> <filter-name>springSecurityFilterChain</filter-name> <url-pattern>/*</url-pattern> </filter-mapping> <listener> <listener-class>org.springframework.web.context.ContextLoaderListener</listener-class> </listener> <listener> <listener-class>org.springframework.web.util.Log4jConfigListener</listener-class> </listener> <listener> <!-- this is for session scoped objects --> <listener-class>org.springframework.web.context.request.RequestContextListener</listener-class> </listener> <listener> <listener-class>org.springframework.security.web.session.HttpSessionEventPublisher</listener-class> </listener> <!-- Handles all requests into the application --> <servlet> <servlet-name>KeyCard</servlet-name> <servlet-class>org.springframework.web.servlet.DispatcherServlet</servlet-class> <load-on-startup>1</load-on-startup> </servlet> <servlet> <servlet-name>tiles</servlet-name> <servlet-class>org.apache.tiles.web.startup.TilesServlet</servlet-class> <init-param> <param-name> org.apache.tiles.impl.BasicTilesContainer.DEFINITIONS_CONFIG </param-name> <param-value> /WEB-INF/tilesViewContext.xml </param-value> </init-param> <load-on-startup>2</load-on-startup> </servlet> <servlet-mapping> <servlet-name>KeyCard</servlet-name> <url-pattern>*.html</url-pattern> </servlet-mapping> <session-config> <session-timeout> 120 </session-timeout> </session-config> <welcome-file-list> <welcome-file>index.jsp</welcome-file> </welcome-file-list> <!-- error-page> <exception-type>java.lang.Exception</exception-type> <location>/WEB-INF/error/error.jsp</location> </error-page --> </web-app> What's wrong?

    Read the article

< Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >