Search Results

Search found 6030 results on 242 pages for 'exists'.

Page 167/242 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

• samba access from win98

  - by SimonSalman

  Hello, the admin installed a new file server in our institute: OpenSuse 11.1 with Samba 3.2.7-11.3.2-2154-SUSE-CODE11. They copied the smb.conf from the old machine (hosting Samba 3.0.0) to the new one. Everything works as before, but one Windows 98 machine can see but not access the file server. It prompts for user authentication, but will not accept any user-password combination. There exists a lot of discussion about the problem on the net, but none provided a clear answer to the problem. EDIT: 1. I changed Win98 registry enable plain-text passwords, and alternatively changed server's smb.conf and /etc/smbpasswd to accept encrypted passwords 2. Further I provide a profile with a user-password combination on Win98 machine similar to one of the samba users-password combinations. 3. I changed smb.conf such that the samba server is the Local Master Browser all these changes are not necessary when using the older samba server. So, I conclude that a configuration problem on the server side is likely. If you need any further information, I will post them here. Best regards, Simon

  Read the article

• HP Laptop recognizes hard drive just long enough to install windows

  - by Joe

  I have an HP laptop, DV6500 (CTO). It refused to boot one day, so I ran some diagnostics (a friend lent me "Hirens Boot Disk", "UBCD" and "PC DR 6"). Everything passed, except for the hdd. I replaced the HDD with a used drive of unknown condition. Installed windows with no problems. Installed the wireless driver, tried to reboot ... no luck. So I went to Best Buy, bought a brand new Western Digital 320gb HDD. Put it in the machine, installed windows (vista home premium). Installed the wired networking driver. Tried to reboot. No luck. Put the first hdd back in the machine, reinstalled windows. Started to install some drivers, went to reboot, and the machine won't come back to life. Put the second hdd in the machine, rinse wash and repeat. I've replaced the memory, even though it passed diagnostics. Problem exists with both brand new memory, and old memory. The BIOS recognizes the hard drive. The computer freezes directly after the bios splash screen, and there is no hard drive activity light. I've tried two linux live distros (gentoo and ubuntu). Neither would run on this laptop, but will on a different HP laptop. UBCD and Hirens Boot Disk both ran, as did PC Doctor 6 which refuses to test anything (gets stuck at "enumerating hard disks"). Is there anything else I can try?

  Read the article

• SQL Server Unattended Install through SSH

  - by Samuel

  I'm trying to install SQL Server from the command line through Cygwin open-ssh. The install works when I log onto the server as Administrator and execute the script through a Cygwin shell, but the install doesn't work when I SSH into the machine using Administrator's credentials and run the exact same command. I've already verified that the SSHD process is running as the Admistrator, and I've verified that the install script is indeed starting under Administrator. Is there something different with the terminal in SSH vs. the Cygwin terminal on the machine that would cause this problem? Specifically what's failing is Sql Server install runs for a while then hangs with a MSI error 1622. "Error opening installation log file. Verify that the specified log file location exists and is writable." If I run both installs, I've noticed that they have different authentication id's in ProcMon, but they have the exact same command line parameters. There has to be something in SSH that is causing permissions issues... Any ideas?

  Read the article

• what means parameter -mailboxcredenctial

  - by cotablise

  H3llo, I am writing regarding the Exchange powershell commands. When I want to use following cmdlets, I have to insert parameter -mailboxcredential Test-OwaConnectivity Test-OutlookWebServices Test-ImapConnectivity Test-PopConnectivity In the Microsoft official site is written: "The MailboxCredential parameter specifies the mailbox credential for a single URL test." I am not sure why this parameter is needed... I inserted incorrect credentials, however the command was finished successfully... Could you tell me reason why this parameter is needed ? Example: Wrong/incorrect credential [PS] C:\>Test-WebServicesConnectivity -ClientAccessServer EXhub1 -MailboxCredential (Get-Credential blablabla) CasServer LocalSite Scenario Result Latency(MS) Error --------- --------- -------- ------ ----------- ----- EXhub1 Default-Fi... GetFolder Failure [System.Net.WebExcept... Without parameter: [PS] C:\>Test-WebServicesConnectivity -ClientAccessServer EXhub1 WARNING: Test user 'extest_91ef41d34eef4' isn't accessible, so this cmdlet won't be able to test Client Access server connectivity. Could not find or sign in with user ********\extest_91ef41d34eef4. If this task is being run without credentials, sign in as a Domain Administrator, and then run Scripts\new-TestCasConnectivityUser.ps1 to verify that the user exists on Mailbox server EXHUB1.****** + CategoryInfo : ObjectNotFound: (:) [Test-WebServicesConnectivity], CasHealthCouldN...edInfoException + FullyQualifiedErrorId : FB9A14B6,Microsoft.Exchange.Monitoring.TestWebServicesConnectivity WARNING: No Client Access servers were tested. Thank you in advance

  Read the article

• CentOS 5.8 - Can't login to tty1 as root after updates?

  - by slashp

  I've ran a yum update on my CentOS 5.8 box and now I am unable to log into the console as root. Basically what happens is I receive the login prompt, enter the correct username and password, and am immediately spit back to the login prompt. If I enter an incorrect password, I am told the password is incorrect, therefore I know that I am using the proper credentials. The only log I can seem to find of what's going on is /var/log/secure which simply contains: 15:33:41 centosbox login: pam_unix(login:session): session opened for user root by (uid=0) 15:33:41 centosbox login: ROOT LOGIN ON tty1 15:33:42 centosbox login: pam_unix(login:session): session closed for user root The shell is never spawned. I've checked my inittab which looks like so: 1:2345:respawn:/sbin/mingetty tty1 2:2345:respawn:/sbin/mingetty tty2 3:2345:respawn:/sbin/mingetty tty3 4:2345:respawn:/sbin/mingetty tty4 5:2345:respawn:/sbin/mingetty tty5 6:2345:respawn:/sbin/mingetty tty6 And my /etc/passwd which properly has bash listed for my root user: root:x:0:0:root:/root:/bin/bash As well as permissions on /tmp (1777) & /root (750). I've attempted re-installing bash, pam, and mingetty to no avail, and confirmed /bin/login exists. Any thoughts would be greatly appreciated. Thanks!! -slashp

  Read the article

• Hung Java JVM failing to respond to kill -3

  - by Hans

  I have a Java VM that is hanging "randomly". I quote the randomly bit, because there is obviously a reason that the VM is hanging, but the hang does not occur periodically. We have the same software running in different customer environments and in those environments the JVM is not hanging. In the process of attempting to troubleshoot the hang the process exists with zero CPU utilization. I then attempt to execute kill -3 and the kill command hangs. No JVM Thread Dump is produced. I have spent time instrumenting the code to periodically log the thread stack traces hoping to catch the JVM in a state that would indicate where the issue lies, but so far this attempt has not born much fruit. Unfortunately I have not been able to reproduce this issue in my lab environment so I am limited by what can be done at the Customer site. The OS's in question are Red Hat Enterprise 5.4 and SUSE 10 running java version 1.6.0_05-b13 Has anyone had this problem? Any ideas on why kill -3 is failing to produce a Java Thread Dump? Thanks!

  Read the article

• Getting Started in SuSE as an Ubuntu User

  - by Subhamoy Sengupta

  I am not a Linux newbie, but haven't touched SuSE in a very very long time (last time I tried it, it was SuSE 7!). Finally now I felt like giving it a try, and many things seem strange or unnecessarily complex. I have a series of questions. How do I ensure that my packages are uptodate? It sounds silly, but I tried the obvious methods already. I have disabled the default repositories that show up when you do zypper lr, and added Tumbleweed and packman repositories (Essentials, Multimedia, Extra). Then I did a sudo zypper ref --force and then sudo zypper dup, and it tells me many dependencies are not met. I have already added solder.allowVendorChange=true to /etc/zypp/zypp.conf, so it should not care which repository the latest versions are in, and just upgrade to it. Even when I chose to skip the packages with unmet dependencies, and seemed like quite a bit happened in the background, I opened Firefox afterwards and the version was 7! I am guessing things did not go as expected. But of course this is not a problem with SuSE, but I am not understanding the system right. How do I do it right? When I start typing arguments of a command, for example sudo zypper install, when I type sudo zypper ins and keep hitting TAB, nothing happens! It always worked in Ubuntu and I feel very uneasy with this. Is this how SuSE is supposed to be? When I try to install something, and I start writing its name, even though the package exists and I am sure of it, hitting TAB does not autocomplete it. This is also quite inconvenient. Why is it not happening? There are many things in SuSE that are really great, and I think I will stay with it and not go back to Ubuntu once I settle these very rudimentary issues. But right now they are giving me a lot of grief! Please help!

  Read the article

• Sever 2008 R2 Powershell Script runs manually, but not as a scheduled task

  - by Aeisor

  I have a Powershell script that runs manually using the Powershell ISE; However, when run as a scheduled task using an administrator's credentials the task does not run with the expected results. The script: $request=new-object System.Net.WebClient $request.DownloadFile("...url...", "C:\path\to\file.csv") The administrator user has Full Control of both the script and the folder it is writing to. The url exists and responds in a reasonable time (<1s). If I run the task manually the status is 0x41301 ("Currently Running") until I eventually end it. I have set the task up using both of these methods: Start a Program: C:\path\to\PS.PS1 Start a Program: C:\windows\system32\WindowsPowerShell\v1.0\powershell.exe with additional options -noninteractive -command "C:\path\to\PS.PS1" Using option 1, the task history shows it has opened an instance of notepad.exe but never terminates it. Using option 2 it completes the task but doesn't download / create the file. I have used Set-ExecutionPolicy Unrestricted as this is not a signed script. Any ideas?

  Read the article

• Accessing a webpage folder with .htaccess in it via apache webdav?

  - by pingo

  I have setup webdav access in order to enable an external user to upload the content of his web page to his folder on my server that is served by apache to the web. This way he could update his web page via webdav. Now the problem is that the user requires a .htaccess file and of course .htaccess breaks webdav probably because it overrides settings. (new files cannot be uploaded anymore via webdav if below specified .htaccess exists) I am running Apache2.2.17 and this is my webdav config: Alias /folderDAV "d:/wamp/www/somewebsite/" <Location /folderDAV> Order Allow,Deny Allow from all Dav On AuthType Digest AuthName DAV-upload AuthUserFile "D:/wamp/passtore/user.passwd" AuthDigestProvider file require valid-user </Location> This config is part of my naive solution to fixing this problem. The idea was to specify an alias to the web page folder where webdav would be enabled and then set AllowOverride to none so that the .htaccess would have no effect. Of course I then found out that in <Location /> AllowOverride directive is not valid. The .htaccess file looks like this: #opencart settings Options +FollowSymlinks Options -Indexes <FilesMatch "\.(tpl|ini)"> Order deny,allow Deny from all </FilesMatch> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)\?*$ index.php?_route_=$1 [L,QSA] ErrorDocument 403 /403.html deny from 1.1.1.1/19 allow from 2.2.2.2 What would be the solution here? I would like to have the web page accessible from the web but at the same time be able to access and modify it via apache's webdav (with digest auth). How would I do that? Also if possible I would like a solution that permits the existence of the .htaccess so that the user still has the power to setup access rules for his web page.

  Read the article

• Problem running “Central Administration” website after windows update at Windows 2003 Server Standar

  - by Magdy Roshdy

  I was have WSS 2.0 and then I upgraded to WSS 3.0 and the old instalation database was SQL 2000, now I have another SQL Server instance called:server_name\MICROSOFT##SSEE . After upgrade every thing works fine and our team started to use the portal and we sent lot of documents and make lot of activities on it. The problem started after installing Windows updates the website suddenly stopped and giving me an error "Cannot connect to the configuration database" If I tried to open SharePoint Products and Technologies Configuration Wizard it is gives me a strange error says: "An exception of type Microsoft.SharePoint.PostSetupConfiguration.PostSetupConfigurationTaskException was thrown. Additional exception information: SharePoint Products and Technologies cannot be configured. The current installation mode does not support SKU to SKU upgrades because there exists an older version of Windows SharePoint Services that must be upgraded first " At this post:http://stackoverflow.com/questions/114398/iis-error-cannot-connect-to-the-configuration-database/249494#249494 the guy of the second answer have the same problem and he suggested a solution but I don't understand well. I tried as he suggested to make the identity of the app pool of the SharePoint web site as "IWAM_server_name " after that the error changed as he said and I web site give me "Server Application Unavailable " and when checked the Event Viewer at the server I found that ASP.NET 2.0 give this exception: "Could not load file or assembly 'System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' or one of its dependencies. Access is denied ." and I don't know how to solve this problem. I'm really want to make my web site working because our team really need these documents and its stuff. I hope I will find some one to help me.

  Read the article

• nginx logrotate config

  - by TomOP

  Whats the best way to rotate nginx logfiles? In my opinion, I should create a file "nginx" in /etc/logrotate.d/ and fill it with the following code and do a /etc/init.d/syslog restart after that. This would be my config (I havn't tested it yet): /usr/local/nginx/logs/*.log { #rotate the logfile(s) daily daily # adds extension like YYYYMMDD instead of simply adding a number dateext # If log file is missing, go on to next one without issuing an error msg missingok # Save logfiles for the last 49 days rotate 49 # Old versions of log files are compressed with gzip compress # Postpone compression of the previous log file to the next rotation cycle delaycompress # Do not rotate the log if it is empty notifempty # create mode owner group create 644 nginx nginx #after logfile is rotated and nginx.pid exists, send the USR1 signal postrotate [ ! -f /usr/local/nginx/logs/nginx.pid ] || kill -USR1 `cat /usr/local/nginx/logs/nginx.pid` endscript } I have both the access.log and error.log files in /usr/local/nginx/logs/ and want to rotate both daily. Can anyone please tell me if "dateext" is correct? I want the log filename to be something like "access.log-2010-12-04". One more thing: Can I do the log rotation every day on a specific time (e.g. 11 pm)? If so, how? Thanks.

  Read the article

• Correct use of SMTP "Sender" header?

  - by Eric Rath

  Our web application sends email messages to people when someone posts new content. Both sender and recipient have opted into receiving email messages from our application. When preparing such a message, we set the following SMTP headers: FROM: [email protected] TO: [email protected] SENDER: [email protected] We chose to use the author's email address in the FROM header in an attempt to provide the best experience for the recipient; when they see the message in their mail client, the author is clear. To avoid the appearance of spoofing, we added the SENDER header (with our own company email address) to make it clear that we sent the message on the author's behalf. After reading RFCs 822 and 2822, this seems to be an intended use of the sender header. Most receiving mail servers seem to handle this well; the email message is delivered normally (assuming the recipient mailbox exists, is not over quota, etc). However, when sending a message FROM an address in a domain TO an address in the same domain, some receiving domains reject the messages with a response like: 571 incorrect IP - psmtp (in reply to RCPT TO command) I think this means the receiving server only saw that the FROM header address was in its own domain, and that the message originated from a server it didn't consider authorized to send messages for that domain. In other words, the receiving server ignored the SENDER header. We have a workaround in place: the webapp keeps a list of such domains that seem to ignore the SENDER header, and when the FROM and TO headers are both in such a domain, it sets the FROM header to our own email address instead. But this list requires maintenance. Is there a better way to achieve the desired experience? We'd like to be a "good citizen" of the net, and all parties involved -- senders and recipients -- want to participate and receive these messages. One alternative is to always use our company email address in the FROM header, and prepend the author's name/address to the subject, but this seems a little clumsy.

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• How does Google geo location service work?

  - by heaosax

  I dont use google maps much, but I was using it today and I clicked the "Show my location" button for the first time, then firefox asked for permission and I clicked "share my location", google maps showed my location pretty accurate. But, how does this system really works? I mean how can google know where I live? I am connecting to the internet with a VPN, so my "public IP" is not from my country, but from sweden, also I use linux and I change the mac of my wireless device, but google still show my location. I know I can disable this feature setting firefox about:config geo.enabled to false, but I am curious about how google can know where I live even when I dont have a real mac address and my IP is not from my real country. Basically I'd like to know if this feature works only because of code that exists in chrome and firefox (which spies my system)? I am worried about anyone knowing where I live, I mean... where is my privacy? Part of the fun about the internet is remaining anonymous.

  Read the article

• Partition is missing in /dev

  - by haimg

  I'm having a strange problem since I moved from Centos5 to Centos6. I have three disks, first two are used as a RAID1, and third one is a stand-alone backup disk that is not listed in /etc/fstab (it is mounded when needed and then unmounted). My problem: After a boot, /dev/sdc exists but /dev/sdc1 does not. Also, the links in /dev/disks are also absent for the first partition of sdc. Disk itself is fine, and if I hot-remove it and plug it back in, /dev/sdc1 appears ok and everything is working. My question: What subsystem manages auto-discovery of disks, partitions, etc. during the boot process (e.g. what creates /dev/disks/by-label)? How do I configure it to scan /dev/sdc too and create all relevant files and links in /dev ? Edit: Here's the relevant part of dmesg output (the only place sdc appears). It does list sdc1, but it's not in /dev! sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdc: sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: DMAR:[DMA Read] Request device [00:1e.0] fault addr 361bc000 DMAR:[fault reason 06] PTE Read access is not set sdb1 sdb2 sdb3 sdc1 sda1 sd 1:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: [sdc] Attached SCSI disk sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk

  Read the article

• How to access original files from before a symlink gets updated, which have since been moved to another dir

  - by Luke Cousins

  We have a website and our deployment process goes somewhat like the following (with lots of irrelevant steps excluded) echo "Remove previous, if it exists, we don't need that anymore" rm -rf /home/[XXX]/php_code/previous echo "Create the current dir if it doesn't exist (just in case this is the first deploy to this server)" mkdir -p /home/[XXX]/php_code/current echo "Create the var_www dir if it doesn't exist (just in case this is the first deploy to this server)" mkdir -p /home/[XXX]/var_www echo "Copy current to previous so we can use temporarily" cp -R /home/[XXX]/php_code/current/* /home/[XXX]/php_code/previous/ echo "Atomically swap the symbolic link to use previous instead of current" ln -s /home/[XXX]/php_code/previous /home/[XXX]/var_www/live_tmp && mv -Tf /home/[XXX]/var_www/live_tmp /home/[XXX]/var_www/live # Rsync latest code into the current dir, code not shown here echo "Atomically swap the symbolic link to use current instead of previous" ln -s /home/[XXX]/php_code/current /home/[XXX]/var_www/live_tmp && mv -Tf /home/[XXX]/var_www/live_tmp /home/[XXX]/var_www/live The problem we are having and would like help with is that, the first thing any website page load does is work out the base dir of the application and define it as a constant (we use PHP). If then during that page load a deployment occurs, the system tries to include() a file using the original full path and will get the new version of that file. We need it to get the old one from the old dir which has now moved as in: System starts page load and determines SYSTEM_ROOT_PATH constant to be /home/[XXX]/var_www/live or by using PHP's realpath() it could be /home/[XXX]/php_code/current. Symlink for /home/[XXX]/var_www/live get updated to point to /home/[XXX]/php_code/previous instead of /home/[XXX]/php_code/current where it did originally. System tries to load /home/[XXX]/var_www/live/something.php and gets /home/[XXX]/php_code/current/something.php instead of /home/[XXX]/php_code/previous/something.php I'm sorry if that is not explained very well. I'd really appreciate some ideas on how to get around this problem if someone can. Thank you.

  Read the article

• mod_rewrite adds .html when redirecting

  - by user12093810293812031

  I have a redirect situation where the site is part dynamic and part generated .html files. For example, mysite.com/homepage and mysite.com/products/42 are actually static html files Whereas other URLs are dynamically generated, like mysite.com/cart Both mysite.com and www.mysite.com are pointing to the same place. However I want to redirect all of the traffic from mysite.com to www.mysite.com. I'm so close but I'm running into an issue where Apache is adding .html to the end of my URLs for anything where a static .html file exists - which I don't want. I want to redirect this: http://mysite.com/products/42 To this: http://www.mysite.com/products/42 But Apache is making it this, instead (because 42.html is an actual html file): http://www.mysite.com/products/42.html I don't want that - I want it to redirect to www.mysite.com/products/42 Here's what I started with: RewriteCond %{HTTP_HOST} ^mysite\.com$ [NC] RewriteRule ^(.*)$ http://www.mysite.com/$1 [R=301,L] I tried making the parameters and the .html optional, but the .html is still getting added on the redirect: RewriteCond %{HTTP_HOST} ^mysite\.com$ [NC] RewriteRule ^(.*)?(\.html)?$ http://www.mysite.com/$1 [R=301,L] What am I doing wrong? Really appreciate it :)

  Read the article

• How to "drag and drop" folders or multiple HTML files into a browser and have them open in multiple tabs

  - by PoorLuzer

  I save pages that I browse on the net and find interesting into a folder called C:\PageSaves Later, during the commute, I open these pages to see what they are and move them into a neatly categorized folder tree. For example, Perl related pages goto C:\Pages\Perl, MySQL related pages goto C:\Pages\MySQL and so on. I was wondering if there is any way I could open any number of HTML files on disc / inside a folder (C:\PageSaves in my case) into Mozilla/FF/K-Meleon etc For example, I would like to just "drag and drop" the folder C:\PageSaves into FireFox and have it open all the .html pages in the folder in a separate tab Right now, if I "drag and drop" multiple HTML files, it just opens the last file in the selection. Have a set of toolbar buttons, basically, a (the) plugin that should allow me to nuke the page (if I don't want to keep the page anymore) from disc or move the file (and its corresponding folder) into a predefined / new folder I am familiar with coding full blown FireFox plugins, so even if something very basic/almost similar exists, I can take it forward. Hints/clues/other methods of achieving the same result are all welcome!

  Read the article

• Application that will identify percentage of your system disk bandwidth used on a user-application by user-application basis?

  - by Warren P

  I always (subjectively) feel my computer is far too slow (however fast it is), and so I'm always looking for ways to measure and understand what my computer is actually doing, that is making it seem "slow" to me. It has been my observation that my software-developer workload is most often disk-bound (I am waiting for Disk I/O) more than CPU bound. What has made it worse, is that I am using a corporate PC that has in-memory active-scanning anti-virus software that I do not have control over, and also some IT department mandated services that seem to suck up a lot of available hard-disk bandwidth. The best tool I have seen (in Windows 7) is the Resource Monitor which I usually acess from the button in the task Manager. The disk IO page, however, seems to label Disk Activity at a very low level (for example, showing the Volume Shadow Storage, which is flushing information obviously written by something ELSE other than VSS itself, and then writes to Pagefile.sys, which are obviously due to Virtual Memory faults in some application). What I would like to know is if a utility exists that can add up all direct disk input and output by user-level process, or find the process or service that caused VM or VSS activity. In that way, I hope, you could establish a real idea of how much of your computer's precious disk subsystem bandwidth is attributable to a particular application. here's a scenario: MyApp.exe writes 100k/s and reads 100k/s directly. VSS ends up writing another 100k/s. pagefaults caused inside MyApp.exe cause another 100k/s of writes. So the total "cost" of MyApp.exe running, during a period of time (let's say 1 second) is 400k/s, whereas you can only directly observe half of that, in Resource Monitor. Is there a smarter disk-IO watching piece of software I can use?

  Read the article

• Have .cmd in startup wait for system wide startup to run.

  - by Dan

  On a computer I'm not an administrator on, there is a startup file (.cmd file in C:\Documents and Settings\All Users\Start Menu\Programs\Startup) for all users. It does several things I don't like, so I have created my own .cmd file which I have placed in C:\Documents and Settings\[user]\Start Menu\Programs\Startup. I want my code to run after the system wide, because my program first undoes the network mappings the system wide file did, and then replaces it with my own network mappings. How can I make my program wait and start as soon as the system wide one is done? (I cannot remove or edit the system wide file). Thanks EDIT: The time that the system wide file takes to runs varies and I would like my file to run right after. The "If Exists" method seems a little to contingent since the system wide script can change or a file could be moved. I am hoping to give my script to a few of my coworkers, so hoping to have it work without me having to update anything. Also, being a linux guy, I don't know cmd code, so please write out any coding suggestions.

  Read the article

• More advanced 'Apple Automator' like software?

  - by OrangeBox

  What I'm looking for is a program similar to Automator or A Better Finder Rename but more extensive / advanced. In my situation we have two files with the same name, one is a MOV the other an XML. We want to use some of the metadata within the XML to rename both files. Then we want to re-arrange the contents of the XML file so that it is compatible with another piece of software we use (I think this process is called mapping?) Essentially some software that takes a bunch of variable from existing file and performs file actions to them. I imagine this would be an easy task using apple-script, but I'm wondering if there is a OSX application similar to Automator that can do the above? Questions are: Is there software that can do the above? Could Automator achieve this? What is the technical name of this kind of process? If no such software exists, what would be the best kind of script to use? eg. Make an Apple Script, python script etc.

  Read the article

• Excel equivilant of java's String.contains(String otherString)

  - by corsiKa

  I have a cell that has a fairly archaic String. (It's the mana cost of a Magic: the Gathering spell.) Examples are 3g, 2gg, 3ur, and bg. There are 5 possible letters (g w u b r). I have 5 columns and would like to count at the bottom how many of each it contains. So my spreadsheet might look like this A B C D E F G +-------------------------------------------- 1|Name Cost G W U B R 2|Centaur Healer 1gw 1 1 0 0 0 3|Sunspire Griffin 1ww 0 1 0 0 0 // just 1, even though 1ww 4|Rakdos Shred-Freak {br}{br} 0 0 0 1 1 Basically, I want something that looks like =if(contains($A2,C$1),1,0) and I can drag it across all 5 columns and down all 270 some cards. (Those are actual data, by the way. It's not mocked :-) .) In Java I would do this: String[] colors = { "B", "G", "R", "W", "U" }; for(String color : colors) { System.out.print(cost.toUpperCase().contains(color) ? 1 : 0); System.out.print("\t"); } Is there something like this in using Excel 2010. I tried using find() and search() and they work great if the color exists. But if the color doesn't exist, it returns #value - so I get 1 1 #value #value #value instead of 1 1 0 0 0 for, example, Centaur Healer (row 2). The formula used was if(find($A2,C$1) > 0, 1, 0).

  Read the article

• Serve web application error messages from Http server

  - by licorna

  I have nginx as a http server with tomcat as a backend (using proxy_pass). It works great but I want to define my own error pages (404, 500, etc.) and that they are served by nginx and not tomcat. For example I have the following resource: https://domain.com/resource which doesn't exist. If I [GET] that URL then I get a Not Found message from Tomcat and not from nginx. What I want is that every time Tomcat responds with a 404 (or any other error message) nginx sends itself a message to the user: some html file accessible by nginx. The way I have my nginx server configured is very easy, just: location / { proxy_pass http://localhost:8080/<webapp-name>/; } And I've configured port 8080, which is tomcat, as not accessible from outside this machine. I don't think that using different location directives in nginx configuration will work, because there are some resources that depend on the URL: https://domain.com/customer/<non-existent-customer-name>/[GET] Will always return 404 (or any other error message), while: https://domain.com/customer/<existent-customer>/[GET] Will return anything different from 404 (the customer exists). Is there any way of serving Tomcat (Application Server) error messages with Nginx (http Server)? To check the message sent by the proxy_pass directive and act upon it?

  Read the article

• XP - ping changes routing table?

  - by Corelgott

  Hey Folks, I have got a real strange behaviour with one of my XP-Sp3 machines. Setup: A Server in the lan (192.168.5.0) proviedes access to all roadwarriors in 10.8.0.0 The DCHP has a static route for all clients pronouncing 192.168.5.235 as gateway for 10.8.0.0 All Clients can ping & access the vpn-machines; everything works like a charm But one Xp-Sp3 is not willing to connect to them. It gets all the same routes as any other sytem in the lan and I trippel-checked - there are no static routes on this machine When I ping any 10.8.0.0 device from this machine, the first two packaged work like a charm; but the next two (and any package after them) fail and get lost. When I look back into the routing table: There is a new route; a special one just for the device I pinged, which points to the right gateway - but which wasn't there earlier... As Long as this route exists the machine can't ping anything on 10.8.0.0. But if I remove the route by hand: The next to ping packages work fine... Has anybody got an idea about that? Anybody every seen such a behaviour? Any hint / help / tip is greatly appreachiated! thx in advance Corelgott Ps: I attach an image of the cmd to clarify things - its in german, but reading a routing table shouldn't be that hard...

  Read the article

• iptables rule on INPUT between 2 ethernet cards on the same host

  - by user1495181

  I have 2 eth cards on the same host. Both connected directly with LAN cable. I set eth0 with ip - 192.168.1.2 I set eth1 with ip - 192.168.1.1 I set this rule: iptables -A INPUT -p tcp -j NFQUEUE --queue-num 0 There are no other rules. (I ran iptables -X,-F) I send TCP syn packet ( with c++ program by using raw socket) from 192.168.1.2 to 192.168.1.1 In wireshark i see that the packet received on eth0, but the iptables rule (above) dosnt apply for this packet. when i sent the packet to remote host and apply this rule on the remote host than it work correct. So, i guess that this is due to the fact that both eth cards exists the same host. . I need to create iptables INPUT rule for local eth card (dest and src on the same machine ). I need it for simplify test. Did i guess the problem correct? is there a way to bypass this? Ps - connected them via switch didn't help. the rule wasn't applied. Run on Ubuntu. TCDUMP show the packet: 10:48:42.365002 IP 192.168.1.2.38550 > 192.168.1.1.34298: Flags [S], seq 0, win 5840, length 0 but logging of iptables like this, has nothing: iptables -A INPUT -p tcp -j LOG --log-prefix '*****************' iptables -A OUTPUT -p tcp -j LOG --log-prefix '#################'

  Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >