Search Results

Search found 25585 results on 1024 pages for 'multiple variables'.

Page 167/1024 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

• Perforce Restore From Multiple Checkpoint Files?

  - by AJ

  Hi all, I am working with a very large (~11GB) checkpoint file and trying to do a -jr (journal restore) operation. About half way through the file, I'm hitting an entry which causes an error to occur. I'm unable to come up with a conventional way to print, edit, and save changes to the offending line. So right now I'm splitting the checkpoint into files of 500k lines each...up to 47 files and counting. My question is, once I have these separate files: Can I run journal restore on each one separately to check for errors? Once fixed, is it necessary to merge them back together again to do my full journal restore? Any other ideas on how to tackle this problem would be appreciated. Thanks in advance, -aj

  Read the article

• Multiple vlans access to shared pbx system

  - by Matt

  I'm new to networking and was looking for some assistance. First off I'm using packet tracer to diagram my scenario as I will be receiving my equipment next week to deploy. Hardware to be used: 2 catalyst 3560 switches all connect to a sonic wall router I have two companies that work in the same office space. I need to keep these companies separate on their own vlan. They will however need to share the phone system. (Packet tracer file uploaded to give those who have the time to see what I put together.) http://dl.dropbox.com/u/86234623/network%20build.pkt Here is my current test scenario: on switch 0 I have: company A on vlan 2 computers 172.16.1.100 and 101 255.255.0.0 FA0/10 FA0/11 company B on vlan 3 computers 172.16.2.102, 255.255.0.0 FA0/12 PBX on a trunk port 172.16.0.5, 255.255.0.0 FA0/5 trunk port on FA0/1 to connect the switches on switch 1 I have: company A on vlan 2 computers 172.16.1.102, 255.255.0.0 company B on vlan 3 computers 172.16.2.100 and 101, 255.255.0.0 trunk port on FA0/1 to connect the switches I can ping the respective computers on the same vlan but cant ping company A to B which is what I want. However neither company can talk (ping) the PBX. Here are the commands I used to configure what I have: switch 0 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 2 int fa0/11 switchport mode access switchport access vlan 2 int fa0/12 switchport mode access switchport access vlan 3 int fa0/5 switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 Switch 1 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 3 int fa0/11 switchport mode access switchport access vlan 3 int fa0/12 switchport mode access switchport access vlan 2 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3

  Read the article

• Network cabling with multiple patch panels?

  - by dannymcc

  I am in the very early stages of planning a network cabling upgrade in our office, mainly to upgrade the old cables from Cat5 to either 5e or 6. I am also planning on upgrading all of our 10/100 switches to 10/100/1000 switches. I would like to have three small wall mounted cabinets spread around the building, each with a patch panel and switch. These would all lead back to our server room. The question is; should I have two patch panels in each wall cabinet, one with 24 or 48 ports that are connected to a matching patch panel in the server room. The second patch panel would then link to each device in that cabinets area. Then I wouldn't put a switch in the small cabinets. All switching would be done in the server room. Or, should I have one main cable from the server room to each of the cabinets - plugged straight into the switch and the patch panel is for devices in the cabinets area? I hope that makes sense!

  Read the article

• Use multiple WSGI mount points in Apache with an Nginx reverse proxy

  - by Thomas

  I am trying to set up multiple virtual hosts on the same server with Nginx and Apache and have run into a curious configuration issue. I have nginx is configured with a generic upstream to apache. upstream backend { server 1.1.1.1:8080; } I'm trying to set up multiple subdomains in nginx that hit different mountpoints in apache. Each would act like the following examples. server { listen 80; server_name foo.yoursite.com; location / { proxy_pass http://backend/bar/; include /etc/nginx/proxy.conf; } ... } server { listen 80; server_name delta.yoursite.com; location / { proxy_pass http://backend/gamma/; include /etc/nginx/proxy.conf; } ... } These mountpoints are pointed at django projects, however each of the url entries are coming back prepended with the apache mountpoint path. So, if I called the django url entry for foo.yoursite.com/wiki/biz/, django appears to be returning foo.yoursite.com/bar/wiki/biz/. Similarly, if I call for the url entry for delta.yoursite.com/wiki/biz/, I get delta.yoursite.com/gamma/wiki/biz/. Is there any way get rid of the prefix being returned on the url entries by django and apache?

  Read the article

• Split Excel worksheet into multiple worksheets based on a column with VBA (Redux)

  - by Ceeder

  I'm rather new to VBA and I've been working with the code generously displayed and explained by Nixda: Split Excel Worksheet... My only challenge is I've been trying desperately to find a way to include the top 3 rows as a title bu it seems to only allow for one. Here's the code have: Dim Titlesheet As Worksheet iCol = 23 '### Define your criteria column strOutputFolder = (Sheets("Operations").Range("D4")) '### <--Define your path of output folder Set ws = ThisWorkbook.ActiveSheet Set rngLast = Columns(iCol).Find("*", Cells(3, iCol), , , xlByColumns, xlPrevious) Set Titlesheet = Sheets("Input") ws.Columns(iCol).AdvancedFilter Action:=xlFilterInPlace, Unique:=True Set rngUnique = Range(Cells(4, iCol), rngLast).SpecialCells(xlCellTypeVisible) If Dir(strOutputFolder, vbDirectory) = vbNullString Then MkDir strOutputFolder For Each strItem In rngUnique If strItem < "" Then Sheets("Input").Select Range("A1:V3").Select Selection.Copy ws.UsedRange.AutoFilter Field:=iCol, Criteria1:=strItem.Value Workbooks.Add Sheets("Sheet1").Select ActiveSheet.PasteSpecial ws.UsedRange.SpecialCells(xlCellTypeVisible).Copy Destination:=[A4] strFilename = strOutputFolder & "\" & strItem ActiveWorkbook.SaveAs Filename:=strFilename, FileFormat:=xlWorkbookNormal ActiveWorkbook.Close savechanges:=False End If Next ws.ShowAllData Is there something I can change to include these lines? Thanks so much, this code provided by Nixda has taught me a great deal!

  Read the article

• script to run sox to combine multiple mono tracks to stereo

  - by Ze'ev

  I have a folder full of .wav audio files. Some are stereo, most are mono splits. The mono split pairs are all named foo bar track.L.wav and foo bar track.R.wav I can use the command line tool sox to combine a mono pair into 1 stereo track like this: sox -M track1.L.wav track1.R.wav track1.Stereo.wav where the first 2 files are the mono pairs, and the third is the output stereo file. This is great, but I'd like to have a script that will automatically find all the mono pairs and combine them into stereo files. I.e., I need it to find all files which have the same name except for the .L. and .R. before the extension, and run sox on them, outputting to a new file with the same name without the L/R suffix. For example, if my folder contains these files: track1.L.wav track2.L.wav track3.L.wav track4.L.wav track1.R.wav track2.R.wav track3.R.wav track4.R.wav track6.wav track7.wav I need to run these commands: sox -M track1.L.wav track1.R.wav track1.Stereo.wav sox -M track2.L.wav track2.R.wav track2.Stereo.wav sox -M track3.L.wav track3.R.wav track3.Stereo.wav sox -M track4.L.wav track4.R.wav track4.Stereo.wav Here's where I am so far: for file in ./*.L.wav; do file2=`echo $file | sed 's_\(.*\).L.wav_\1.R.wav_'`; out=`echo $file | sed 's_\(.*\).L.wav_\1.STEREO.wav_'`; echo $file - $file2 - $out; done That works, but when I replace the echo line with sox -M $file $file2 $out; it doesn't work; spaces in the filenames cause it to fail.

  Read the article

• Why does rsync spawn multiple processes for me?

  - by Yoga

  I am using the following cron statement to backup from one folder to another folder in the same machine: 19 21 * * * root rsync -ac --delete /source/folder /dest/folder When I use pstree, I see the cron forked three processes +-cron---cron---rsync---rsync---rsync And ps 9972 ? Ds 1:00 rsync -ac --delete /source/folder /dest/folder 9973 ? S 0:29 rsync -ac --delete /source/folder /dest/folder 9974 ? S 0:09 rsync -ac --delete /source/folder /dest/folder Why are three processes? Can I limit to only one?

  Read the article

• Multiple public IPs through DD-WRT without 1-to-1 NAT

  - by Stephen Touset

  I've done a search here and wasn't able to find anything relevant to my situation. I apologize in advance if I've missed an existing post on the topic. Our ISP has provided us with 6 static IP addresses. We are currently using two of them (plus one for the Comcast-provided router). One of the static addresses routes to our internal network, and the other goes to our VOIP phone system. Unfortunately, the Comcast machine doesn't support QoS, so our VOIP calls have been choppy. We plan to put the Comcast-provided router into bridge mode and replace it with an ASUS RT-N16 running DD-WRT. However, I'm unsure how to set up DD-WRT to function similarly to our existing Comcast router. The Comcast router's WAN IP is the first of our static IP addresses. We did not need to provide an internal LAN IP address — simply connecting machines that use our other public addresses to the LAN ports on the Comcast router is enough for it to route between the connected machines and our internet connection. Is there a way to do a similar setup through the DD-WRT? Thanks in advance.

  Read the article

• Assigning multiple IPv6 addresses on a Server

  - by andrewk

  Let me uncover my intent. My host provides hundreds of IPV6 addresses free, but charge for an IPV4 address. I have several sites under one server and I was wondering if I can give each site/domain it's own ipv6 address. Is that even possible? If so how? I've read quite a bit about ipv6 but I do not understand it as clear as I'd like. My main goal is, for each domain/site to have it's own unique IP, so someone can't do a reverse ip look up and see what sites I have on that server. Thanks in advance for the patience.

  Read the article

• multiple php compiler on single apache installation

  - by getmizanur

  elloo, i have some old php scripts which runs on php-5.2.x and the current server has php-5.3.x. to get around this problem,i have got two options one is to downgrade php-5.3.x or install php-5.2.x and php-5.3.x at the same time where php-5.2.x serve cgi script. i have decided go for the second option i have followed this tutorial and i can get most of it working however except execution of shell script which selects php-cgi version. i cannot get apache to execute this script. how do i get apache to execute #!/bin/sh # you can change the PHP version here. version="5.2.6" # php.ini file location, */php-5.2.6/lib equals */php-5.2.6/lib/php.ini. PHPRC=/etc/php/phpfarm/inst/php-${version}/lib/php.ini export PHPRC PHP_FCGI_CHILDREN=3 export PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=5000 export PHP_FCGI_MAX_REQUESTS # which php-cgi binary to execute exec /etc/php/phpfarm/inst/php-${version}/bin/php-cgi my apache vhost.conf <VirtualHost *:80> ServerName 526.localhost DocumentRoot /home/getmizanur/public_html/www <Directory "/home/getmizanur/public_html/www"> AddHandler php-cgi .php Action php-cgi /php-fcgi/php-cgi-5.2.6 </Directory> </VirtualHost> can some one tell me what am i doing wrong? thanks in advance. solution: if i did a2dismod php5 then the above configuration worked. when a2enmod php5 had been activated, apache was executing php5.3 instead of php5.2 even after telling apache to execute php5.2 shell script. to solve my problem, i had to change my virtualhost configuration <VirtualHost *:80> ServerName 526.localhost DocumentRoot /home/getmizanur/public_html/www DirectoryIndex index.php <Directory "/home/getmizanur/public_html/www"> AddHandler php-cgi .php Action php-cgi /php-fcgi/php-cgi-5.2.6 <FilesMatch "\.php"> SetHandler php-cgi </FilesMatch> </Directory> </VirtualHost> presto, it started working.

  Read the article

• HP Procurve Issue Passing Multiple VLANs over a link

  - by MichaelRwat

  Just to start off with I am a Cisco guy that got placed into an HP project. Basic topology overview from outside in: ASA 5505 with two Ethernet connections to a 2910-24 port switch. This switch is then (Cisco Trunking) to a 2626 switch passing vlan (1 untagged and 100 tagged)between them. I created SVI's on each of the switches for both VLAN's for testing purposes. I can not get vlan 100 to pass across this link. I also have trunks configured to AP's off of the switch and can not ping the vlan 100 BVI on the AP's but can reach the vlan 1 BVI. Port 25 on Access layer (2626) connects (trunks) with port A1 of 2610. STP is not running at all on any switch (this is not my network I can't change this nor did I design this) Distribution Sw: MP1-0# show run ip default-gateway 10.100.100.100 vlan 1 name "DATA" untagged 1-22,24-A1,B1 ip address 10.100.100.6 255.255.255.0 no untagged 23 exit vlan 100 name "GUEST" untagged 23 tagged 24-A1 ip address 10.100.102.6 255.255.255.0 exit Access Sw: ip default-gateway 10.100.100.100 vlan 1 name "DEFAULT_VLAN" untagged 1-26 ip address 10.100.100.5 255.255.255.0 exit vlan 100 name "GUEST" ip address 10.100.102.5 255.255.255.0 tagged 15,25 exitt From the ASA I can ping the vlan 100 address of the 2610 but not the 2626 (10.100.102.6)[Not passing the "trunk"] If I plug into an access port vlan 100 of the 2626 I can ping the SVI for vlan 100 as intended. I can not ping across the "trunk" over vlan 100 but I can across vlan 1. There may be something obvious I'm missing but please review my configuration and thank you for the assistance.

  Read the article

• How to push configurations to multiple Cisco Switches

  - by nixda

  Assume I have around 50 Cisco IE2000 Switches connected together and I want to reconfigure some settings, the same settings for every switch. Normally I would open a command line session via Putty and paste the commands. But as the number of switches is growing, even this method takes its time. I am aware of Kiwi CatTools. Unfortunately it's not free so I'm wondering if there are other efficient ways to configure a large number of Cisco switches.

  Read the article

• How to host multiple mail domains with courier?

  - by Dave Vogt

  I had my server set up with generic aliases in /etc/courier/aliases/users, which worked fine. But today I wanted to host some new domains, where addresses overlap. What I need is that [email protected] goes to account "dv", but [email protected] goes to account "d2". So I set up a new file containing fully qualified addresses ([email protected]: dv) instead of the previous dave: dv. But somehow, courier-smtpd doesn't accept mail to these addresses anymore. makealiases -dump prints all the aliases the way they should be.. so i'm a bit stuck.

  Read the article

• Sonicwall with failover, multiple subnets, and preferred WAN interface per subnet

  - by Dan

  I am trying to set up my Sonicwall TZ-210 as follows: Two WAN interfaces (different ISPs), set up in failover mode. Two LAN interfaces with different subnets Each LAN subnet will have a preferred outbound WAN interface, but would failover when necessary. In this way, each ISP is being used for a separate subnet of my network, but both subnets could failover to the other ISP if their primary went down. I know how to do 1 and 2, but I don't know how to do 3. I could set up a route for each subnet to go through a specific interface, but what would happen in the event of a failover? Would it automatically update those routes? Thanks!

  Read the article

• Duplicate IP address detection with multiple NICs

  - by sfink

  I am using arping -D to detect duplicate IP addresses within a network when setting up servers. (The network is controlled by someone else, and we have had many issues with IP allocation in the past.) It works fine as long as my host has a single NIC on a given VLAN, but when my host has more than one (I have one with 9 NICs on one VLAN and 1 on the other), arping -D always returns false collisions. The problem is that all 9 of my NICs respond to an ARP request for any of the IPs on those NICs. (These are real physical NICs, not aliases or anything.) I send out one ARP request packet, and get 9 ARP is-at ARP replies, one for each MAC address. I could implement my own solution by sniffing packets and checking for any replies with a MAC address other than the local NICs', but it seems like there ought to be an easier way.

  Read the article

• Daisy-chaining network switches with multiple cables

  - by user72153

  This might just be the dumbest question you'll ever read, but I digress. Say I have two 100Mbps Ethernet switches with 2 computers on each, connected together by a single cable. This way, the two PCs on each switch share the 100Mbps bandwidth with the others. If I added another cable between the 2 switches, would there be 200Mbps throughput available between the switches? Or am I completely off my rocker? Thanks for the help.

  Read the article

• Windows file locks allowing multiple users to write to open file over network

  - by JPbuntu

  I have 6 windows computers (xp,vista,7) that need to access a samba share (Ubuntu 12.04). I am trying to make it so only one client can open a file at a given time. I thought this was pretty standard behavior of file locks, but I can't get it to work. The way it is right now a file can be open by two users, and changed and saved by either one of them. The last file saved overwrites what ever changes the other user made. At first I thought this was a Samba configuration problem, but I get this behavior even between two windows machines. So far I have only tested: Windows Xp Windows Vista Windows XP Samba << Windows Vista and both give the same behavior. When I tested the Samba configuration, I had set strict locking = yes and get errors logged like this: close_remove_share_mode: Could not get share mode lock for file _prod/part_number_list_COPY.xlsx Eventually all of the files are going to be moved onto the Samba share, so that is the configuration I am most concerned about fixing. Any ideas? Thanks in advance. EDIT: I tested an excel file again, and it is now working properly in both above mentioned cases, I am also no longer getting the above mentioned error. I don't know what happened, perhaps a restart fixed it? (also works with strict locking = no) Although I still need to find a solution for the CAD/CAM files we use, the software is Vector and it does not seem to be using file locks. Is there any software that I can use to manage these files, so two people can't open/edit them at a time? Maybe a windows application that forces file locks? Or a dirt simple version control system? (the only ones I have seen at are too complicated for our needs).

  Read the article

• Is this normal? Multiple httpd process

  - by ilcreatore

  I'm testing a new Server. This isnt really a peak time for my server (2pm), but still its running a bit slow, I was checking the ESTABLISHED connections using the following command: # netstat -ntu | grep :80 | awk '{print $5}' | cut -d: -f1 | sort | uniq -c | sort -n http://i.stack.imgur.com/cZuvP.jpg My MaxClients are set to 50. So as you can see on the picture, only 10 people are eating most of my ram. I got a server with 4GB Ram (2.7GB free for apache) but each apache process is eating 53MB each, wich mean im only allowed to accept 50 process. The KeepAlive = Off, but I notice those connections arent closing fast enough, is that normal?

  Read the article

• How can I add GET variables to the end of the current page url using a form with php?

  - by zeckdude

  I have some database information that is being shown on a page. I am using a pagination class that uses the $_GET['page'] variable in the url. When you click on a different pagination anchor tag, it changes $_GET['page'] to a new number in the url and shows the corresponding results. I have sort and search features which uses the $_GET['searchby'] and $_GET['search_input'] variables. The user enters their search or sort criteria on a form that is using GET. The variables are then put into the url allowing for the correct results to be shown. The problem I am having is that whenever I click on a pagination link, it adds that to end of the url and erases the search or sort GET variables. The same thing happens when I submit the search/sort form. How can I add GET variables to the end of the current page url using the anchor tag and search/sort form?

  Read the article

• windows server 2008r2 with terminal services in multiple networks with different users

  - by phhe

  is there a way to let terminal services make some kind of 'abstraction' over the physical network interfaces of the server so they can be managed via gpo to grant or prohibit access for different users? the basic idea is to have 2 network interfaces (user and server/management) and not letting users within terminal sessions access the server/management network. or is this just impossible ? what would be a better way to do this ?

  Read the article

• multiple wildcard entries

  - by Murali

  my client has around 300,000 domains and they just have a wildcard for all of them * A 12.12.12.12 Now they want to create a sub domain that points to a different IP and still have the flexibility of wildcard, something like ww1.* A 24.24.24.24 * A 12.12.12.12 Looks like in BIND, the lower "*" is catch-all and taking over every query and hence ww1 is not working. One of solutions offered by IT folks was to create seperate 300K zones for just "ww1" and leave the "*" wildcard. Are there any other DNS software's that can achieve this task easily? Any other ways to deal?

  Read the article

• Running multiple services on Port 443, Tunnel SSH over HTTPS

  - by lajuette

  Situation: I want to tunnel SSH sessions through HTTPS. I have a very restrictive firewall/proxy which only allows HTTP, FTP and HTTPS traffic. What works: Setting up a tunnel through the proxy to a remote linux box that has a sshd listening at port 443 The problem: I have to have a web server (lighty) running at port 443. HTTPS traffic to other ports is forbidden by the proxy. Ideas so far: Set up a virtual host and proxy all incoming requests to localhost: (e.g. 22) $HTTP["host"] == "tunnel.mylinux.box" { proxy.server = ( "" => (("host" => "127.0.0.1", "port" => 22)) ) } Unfortunately this won't work. Am i doing something wrong, or is there a reason, that this won't work?

  Read the article

• Cisco ASA 5505 site to site IPSEC VPN won't route from multiple LANs

  - by franklundy

  Hi I've set up a standard site to site VPN between 2 ASA 5505s (using the wizard in ASDM) and have the VPN working fine for traffic between Site A and Site B on the directly connected LANs. But this VPN is actually to be used for data originating on LAN subnets that are one hop away from the directly connected LANs. So actually there is another router connected to each ASA (LAN side) that then route to two completely different LAN ranges, where the clients and servers reside. At the moment, any traffic that gets to the ASA that has not originated from the directly connected LAN gets sent straight to the default gateway, and not through the VPN. I've tried adding the additional subnets to the "Protected Networks" on the VPN, but that has no effect. I have also tried adding a static route to each ASA trying to point the traffic to the other side, but again this hasn't worked. Here is the config for one of the sites. This works for traffic to/from the 192.168.144.x subnets perfectly. What I need is to be able to route traffic from 10.1.0.0/24 to 10.2.0.0/24 for example. ASA Version 8.0(3) ! hostname Site1 enable password ** encrypted names name 192.168.144.4 Site2 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.144.2 255.255.255.252 ! interface Vlan2 nameif outside security-level 0 ip address 10.78.254.70 255.255.255.252 (this is a private WAN circuit) ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passwd ** encrypted ftp mode passive access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_1_cryptomap extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 access-list inside_nat0_outbound extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-603.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 access-group inside_access_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 10.78.254.69 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy aaa authentication ssh console LOCAL http server enable http 0.0.0.0 0.0.0.0 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer 10.78.254.66 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal telnet timeout 5 ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside threat-detection basic-threat threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list group-policy DfltGrpPolicy attributes vpn-idle-timeout none username enadmin password * encrypted privilege 15 tunnel-group 10.78.254.66 type ipsec-l2l tunnel-group 10.78.254.66 ipsec-attributes pre-shared-key * ! ! prompt hostname context

  Read the article

• Running multiple services on different servers with IPv6 and a FQDN

  - by Mark Henderson

  One of the things NAT has permitted us to do in the past decade is split physical services onto different servers whilst hiding behind a single interface. For example, I have example.com behind a NAT on 192.0.2.10. I port-forward :80 and :443 to my web server. I'm also port forward :25 to my mail server, and :3389 to a terminal server and :8080 to the web interface of my computer that downloads torrents, and the story goes on. So I have 5 port forwardings going to 4 different computers on example.com. Then, I go and get me some neat IPv6. I assign example.com an IPv6 address of 2001:db8:88:200::10. That's great for my websites, but I want to go to example.com:8080 to get to my torrents, or example:3389 to log on to my terminal server. How can I do this with IPv6, as there is no NAT. Sure, I could create a bunch of new DNS entries for each new service, but then I have to update all my clients who are used to just typing example.com to get to either the website or the terminal server. My users are dumber than two bricks so they won't remember to connect to rdp.example.com. What options do I have for keeping NAT-style functionality with IPv6? In case you haven't figured it out, the above scenario is not a real scenario for me, or perhaps anyone yet, but it's bound to happen eventually. You know, with devops and all.

  Read the article

• DHCP server with multiple interfaces on ubuntu, destroys default gateway

  - by Henrik Kjus Alstad

  I use Ubuntu, and I have many interfaces. eth0, which is my internet connection, and it gets its info from a DHCP-server totally outisde of my control. I then have eth1,eth2,eth3 and eth4 which I have created a DHCP-server for.(ISC DHCP-Server) It seems to work, and I even get an IP-address from the foreign DHCP-server on the internet facing interface. However, for some reason it seems my gateway for eth0 became screwed after I installed my local DHCP-server for eth1-eth4. (I think so because I got an IP for eth0, and I can ping other stuff on the local network, but I cannot get access to the internet). My eth0-specific info in /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.0.1.1 netmask 255.255.255.0 network 10.0.1.0 broadcast 10.0.1.255 gateway 10.0.1.1 mtu 8192 auto eth2 iface eth2 inet static address 10.0.2.1 netmask 255.255.255.0 network 10.0.2.0 broadcast 10.0.2.255 gateway 10.0.2.1 mtu 8192 My /etc/default/isc-dhcp-server: INTERFACES="eth1 eth2 eth3 eth4" So why does my local DHCP-server fuck up the gateway for eth0, when I tell it not to listen to eth0? Anyone see the problem or what I can do to fix it? The problem seems indeed to be the gateways. "netstat -nr" gives: 0.0.0.0 --- 10.X.X.X ---- 0.0.0.0 --- UG 0 0 0 eth3 It should have been 0.0.0.0 129.2XX.X.X 0.0.0.0 UG 0 0 0 eth0 So for some reason, my local DHCP-server overrides the gateway I get from the network DHCP. Edit: dhcp.conf looks like this(I included info only for eth1 subnet): ddns-update-style none; not authoritative; subnet 10.0.1.0 netmask 255.255.255.0 { interface eth1; option domain-name "example.org"; option domain-name-servers ns1.example.org, ns2.example.org; default-lease-time 600; max-lease-time 7200; range 10.0.1.10 10.0.1.100; host camera1_1 { hardware ethernet 00:30:53:11:24:6E; fixed-address 10.0.1.10; } host camera2_1 { hardware ethernet 00:30:53:10:16:70; fixed-address 10.0.1.11; } } Also, it seems that the gateway is correctly set if I run "/etc/init.d/networking restart" in a terminal, but that's not helpful for me, I need the correct gateway to be set during startup, and i'd rather find the source of the problem

  Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >