Search Results

Search found 17771 results on 711 pages for 'dhcp option'.

Page 168/711 | < Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• Teamed network cards on a Proliant Server

  - by Matt

  We have 4 network cards in a Proliant server with Server 2008R2 running Exchange 2010, with 1 card set to a static IP address and the other 3 set to DHCP. I just need some clarification as I have not teamed network cards. Do all the network cards need to have a static IP when I set as a team. The connection that has the static IP is the IP that I need to use for the Server. Is it possible to set the teamed cards to the same static IP or do I have to change the static IP to another IP then use it for the teamed IP? I will be using HP Network Configuration Utility to set this up.

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the DD-WRT firmware. Is it possible to use this router as an ordinary computer, running only a DNS server, disabling all other features such as DHCP, WLAN, etc? Connecting it to my other router, should I simply run a cable into the WAN-port of the Linksys router?

  Read the article

• new SBS 2011 Standard problems

  - by Damon

  Brand new SBS 2011 install. I went to remove the DHCP server role. It went into a "Preparing to configure Windows. Do not turn off your computer." Been there for hours. Finally, decided to power off and restart. After boot up, the same window and message appear and it just sits there spinning. "Preparing to configure Windows. Do not turn off your computer." I'd love to get this installed before the end of the day but it doesn't look like that's possible. Any ideas on how to get passed this?

  Read the article

• Internet connection very slow after Linksys configuration

  - by NLV

  Hello We have this network setup Server1 - DHCP server, Domain Controller, AD Lease line for Internet connection From lease line to Linksys router (we dont use wireless though) From linksys to Netgear (24 port Switch) and vonage (VoIP) Netgear to all our machines We configured Linsys with the static IP and DNS server addresses our ISP gave and we have routed it correctly. All our work machines are configured with Get IP automatically DNS server addresses our ISP gave The problem is that none of the sites are getting opened promptly. It is taking around 5 minutes to load google.com. But we are able to ping all the sites. What could be the problem?

  Read the article

• What is blocking incoming packets to port 67?

  - by Peter Robertson

  I have a DSP connected to a Windows 7 laptop by Ethernet. The laptop has all firewalls disabled (I've even tried stopping the Windows firewall service and DHCP). The DSP is sending well-formed BOOTP broadcast packets every 3 seconds to port 67. Wireshark running on the laptop sees these BOOTP packets coming in. I have a program running on the laptop with a socket successfully bound to port 67. I can see this using CurrPorts.exe. Nothing else is shown as accessing port 67. The program never sees any packets coming in. If I run a program in the DSP that sends ordinary UDP packets to port 67, Wireshark sees them coming in and reports that they are corrupt BOOTP packets, but now, my program gets them. Any idea what's going on here?

  Read the article

• Windows 7 - Virtualbox host only adapter doesn't get an IP

  - by Craig

  When I create a new host only network adapter, it will not set the IP address I assign to it. After I save the IP address & netmask it looks like it works (I see the Windows 7 User Account Control verification box), but the IP address doesn't get stored on the adapter. I have tried adding/removing the adapter from within virtualbox and settings the values manually in the Windows aapter settings dialogue. I am using a Windows 7 host. Does anyone know why the settings don't get saved, or how to get more information? C:\Program Files\Oracle\VirtualBox>VBoxManage list hostonlyifs Name: VirtualBox Host-Only Ethernet Adapter GUID: 1721835e-e2c8-4f52-90fe-df7227ebe037 DHCP: Disabled IPAddress: 0.0.0.0 NetworkMask: 0.0.0.0 IPV6Address: IPV6NetworkMaskPrefixLength: 0 HardwareAddress: 00:00:00:00:00:00 MediumType: Unknown Status: Unknown VBoxNetworkName: HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter

  Read the article

• Strange DNS problem [seems to be IPv6 issue]

  - by Homer J. Simpson

  Hi, I'm experiencing strange problems with my Kubuntu 9.10 when doing DNS requests from various applications. The requests are extremely slow, so loading any pages in Firefox or Konqueror, doing package installations in Kpackagemanager and other apps is really painful, while for example Opera doesnt have any problems, and ping is normally fast as well for DNS pings. I checked the proxy settings of both the used applications as well as of the general system and there are none, so to me it doesn't seem as there was something inbetween.. Does anybody have an idea on what to check for possible problem sources or how to solve this ? I'm behind a DSL home router which does the DHCP (and works well with my other computer). Any kind of advice would be really helpful. Edit: It seems to be some kind of IPv6 problem, as I could get it to work by disabling IPv6 explicitly in Firefox. Is there a general solution to this ?

  Read the article

• How to give virtual machine access to the Internet, but block from LAN?

  - by Pekka

  I am setting up a virtual machine using Microsoft Virtual PC in Windows 7. The VM will run a Windows XP. I want to set up a public-facing server in it for web pages, subversion and other things, and instruct the router to port forward any requests to that Virtual Machine. I managed to do that - I assigned the VM to the network adapter, and it is now acting as just another DHCP client - but to increase security I would like to block the VM from the rest of the LAN, so it accepts only incoming connections from the Internet. For this to be effective in case of a compromise, it would have to happen on VM level as far as I can see. Can this be done?

  Read the article

• How can I solve Windows PPTP VPN issues?

  - by Robin M

  I'm having persistent problems with Windows PPTP VPN connections. The VPN appears up whilst the tunnel won't transfer traffic (ping to a remote IP within the VPN works for a while, and then fails). The client receives routing information via DHCP. When the connection fails, the routing table is still correct so I don't think it's a routing problem. My internet connection is via an ADSL2 line. There's software to deal with PPTP problems, like TunnelRat, but I don't want to install v1.1 of the .NET framework and I'd rather get to the bottom of the problem (I have multiple VPN connections and some are more unreliable than others). What can I do to get to the bottom of this? Alternatively, what can I do to keep the connection alive?

  Read the article

• Why is this static routing not working ?

  - by geeko

  Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

  Read the article

• Weird behaviour with OpenVPN: can not connect to a few websites

  - by Gaby Solis

  My OpenVPN server is Ubuntu 10.04.4 LTS and openvpn version is 2.x My client is on Win 7. He can access most sites but not Youtube, Facebook, Twitter, groups.google.com, etc My server.conf is: local x.x.x.x port 1194 proto udp dev tun ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key dh /etc/openvpn/keys/dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status /etc/openvpn/keys/openvpn-status.log verb 4 I can access Youtube etc using SSH Tunnel + SOCKS Proxy, and the Ubuntu server can access all sites. so nothing is wrong with the Ubuntu server. With little information I can provide, I am not looking for a quck solution. How can I debug?

  Read the article

• Trusted Root certificates regularly disappear on Windows 7

  - by Evgeny

  I've installed several self-signed certificates on my Windows 7 Ultimate x64 machine for development purposes. One was installed into Trusted Root CAs and 2 were installed into My Certificates and Trusted People. Every day or two the certificate installed into Trusted Root CAs disappears and I have to re-install it! This is annoying the hell out of me. Why is it happening and how do I stop it? The other certificates (installed into other stores) do not disappear. My first thought was some kind of Group Policy, but my machine is not part of a domain - though it does obtains its IP address from a corporate DHCP server, so I'm not sure if they can somehow still manage to apply Group Policy to me.

  Read the article

• cannot access my own computer through My Network Places

  - by vgv8

  My home Windows XP Pro SP3 machine is DHCP client receiving configurations from ISP. Trying to access in WindowsExplorer -My Network Places - Microsoft Windows Network shows Workgroup with a delay of 3 min and then popups messagebox: Microsoft Windows Network Workgroup is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.The list of servers for this workgroup is not currently available OK I am logged-in as local machine Administrator. The internet is accessible (I am writing this post through it) The Firewall is disabled The "Computer Bowser" and all networking services, I could find, are running Control Panel -- Network Connections -- Properties (of connection) --- Internet Protocol (TCP/IP), btn Properties --- --- tab General, btn "Advanced..." -- tab WINS-- rbtn "Enable NetBIOS over TCP/IP" checked Why cannot I access my own PC (and shares on it) through My Network Places What is the possible problem? How to daignose the problem?

  Read the article

• How to configure 2nd network card for use in VMWare Workstation?

  - by Timo

  Hi all, I am using VMWare Workstation 6.5, connected to my network with a bridged adapter so that the virtual machine OS (Windows XP) has its own IP adress. This just worked out of the box. Now my host machine (Windows Vista) has an additional network card that is directly connected to another computer using a crossover cable (and fixed IP adress 10.1.1.4, while the "main" network connection is using DHCP with IP in the 192.68.0.* range). How can I use that network connection as well in the virtual machine? Do I need to bridge my 2nd network adapter to some VMnetX adapter? Do I need to add a host virtual adapter? I do not know much about networks, and the VMWare network settings really confuse me :-) Thanks, Timo

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the DD-WRT firmware. Is it possible to use this router as an ordinary computer, running only a DNS server, disabling all other features such as DHCP, WLAN, etc? Connecting it to my other router, should I simply run a cable into the WAN-port of the Linksys router?

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• gigabit network with adsl modem

  - by user51006

  Hi, i would like to build a gigabit network to connect the different computers at my home. I already have an 100Mb adsl router/modem but i have an hard time to find a 1000Mb one, so i came up with the idea of using a normal 1000Mb router or switch to put between the adsl modem and the computers. So i only use the adsl modem to connect to the internet and the gigabit router as dhcp to connect the different computers. But to get to the question. Will the 100Mb adsl router slow down my network? Will data travel like pc gigabit router computer or pc gigabit router adsl router gigabit router pc. My gut says it will go like in the first option but i have seen network hardware do some weird stuff. What do you think?

  Read the article

• Remote connection to dynamic public ip & private ip addresses

  - by user53864

  Many times I connected to windows computer which has static public ip address via remote desktop over wan links. I'm wondering how could I connect to the remote computer that has dynamic public ip address & private ip addresses assigned. I've 2 systems at home: xp system-------connected to internet(dynamic public ip) & allowed other users to connected to the internet on the interface. windows vista system--------enabled dhcp on the interface to access internet from xp. How could I remotely connect from my office to the 'vista system'?. If I've a router/modem at my home it may be possible to allow the ports for the system but I don't. Any tips?

  Read the article

• Cannot assign port 4 to WAN on TP-Link WR740N by DD-WRT wiki

  - by Victor Sergienko

  I'm following the DD-WRT instruction to get TP-Link WR740N v3's Port 4 on a different VLAN, but this doesn't happen. First, I have no "Setup VLANs" settinngs tab in DD-WRT v24-sp2 (07/20/12) std r19519. I can get Internet on Wi-Fi if assigning eth1 to "WAN Port", but then all Ethernet ports get on the same VLAN and any wired connection grabs the DHCP address and Internet connection from router. When following the "old" instruction, if I run, say, nvram set vlan2ports="2 5*", should there appear a new interface, vlan2, in ifconfig, after ifconfig vlan2 up? It doesn't - does it mean there is no support for different VLANs in my software/hardware? What am I missing? Is it impossible to create more VLANs on TP-Link740?

  Read the article

• Connect to wired and wireless networks at same time, Ubuntu

  - by Gary Chambers

  Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

  Read the article

• design a large scale network for an organization

  - by Essam

  i want to design a large scale network for an organization with HQ and two branches. i want to use a class A subnet. if i am using the network address 30.0.0.0 for the whole organization how can it be different from another organization company or whatever which is using the same address in another country? now i have the three locations for this organization,so i need 5 subnets [one for the HQ,two for branch A and branch B , one for connecting A to HQ and one for connecting branch B with HQ since i will use central DHCP server at the HQ,is that (number of subnetting) right? is it advisable to use class A or class B for this organization it term of address that will be wasted (let's say it is a university with two branches in two different states)?!

  Read the article

• Netboot Intel Macs without BSDP

  - by notpeter

  I have a netboot setup with DeployStudio that works great in my lab, but doesn't work on our main network. After some digging, I believe it's because our network admins are filtering BSDP (Boot Service Discovery Protocol) on our subnet at the switch level. Is it possible to hard code which server my clients (early 2007 iMac Core2Duos) should boot from without relying on BSDP? Perhaps relevant details: I do not have control over switch configs or DHCP settings. Client and server are running 10.6 Snow Leopard. The clients see the netboot server advertising itself in the 'Startup Disk' system preferences pane, but when I go to netboot it just leaves me with a flashing globe.

  Read the article

• Virus blocking incoming connections ?

  - by Benoît

  Hello, on my windows 2003 server, all incoming connections are dropped. I can see them getting in using Wireshark, but even a single ping from another computer fails. All locally initiated connection work fine (i'm asking from the server). This server is the DC/DHCP/DNS/File server, so computer clients are in the dark. I've run varius antivirus and removal tools without any luck. The Windows Firewall is disabled. I'm wild-guessing at some virus/worm. How can i check why these incoming ICMP/TCP SYN/etc are dropped ? Anyone has any knowledge about such situations ? Thanks.

  Read the article

• Virtualization deployment for datacenter

  - by bogha

  Hi, my company is going to deploy an IT Infrastructure on a virtual platform, can you please help me with the following: 1- which one do you recommend, Cisco Unified computing system ( cisco + emc + vmware )or HP Blades( virtualization solution + HP Storage )? 2- i Need to install a DNS Server, Web server, cpanel for managing hosting packages and Microsoft layer of product for usingg in the corporate infrastructur ( active directory, Local DNS, Exchange server, DHCP, Global catalog ) what is the minimum requirments for these servers ( in terms of CPU and Memory ) . 3- what is the best way to implement a redundant solution in a virtual environment. thank you

  Read the article

< Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >