Search Results

Search found 12281 results on 492 pages for 'ip blocking'.

Page 168/492 | < Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >

  • Running SUN UDS 5213 on Windows 7

    - by Lebo
    I am getting this error when I try to install Sun ONE UDS 5213 on Windows 7: This Windows NT system does not have TCP/IP installed. Please install the TCP/IP package before installing Sun ONE UDS Please help.

    Read the article

  • how can I reconnect DSL in cisco router 877w

    - by Sulaiman
    Hi All, I've configured ADSL and added a new public LAN ips for the router. How can I reconnect DSL connection and apply the new configuration without executing the command reload this is the commands I am using for DSL configuration config terminal interface dialer 0 ppp chap hostname User ppp chap password 0 Pass exit exit wr mem and this is the commands I am using for adding IP addresses: configure t interface vlan 1 ip address xx.xx.xx.xx 255.255.255.252 Secondary exit wr mem thank you

    Read the article

  • LAN connection problem

    - by Pradi
    how to connect to different system within the lan? im getting messages back when pinged with host ip address and also for default gateway. But messages pinged to another ip address with in my lan are not comming back? please help me out.

    Read the article

  • LAN connection problem

    - by Pradi
    how to connect to different system within the lan? im getting messages back when pinged with host ip address and also for default gateway. But messages pinged to another ip address with in my lan are not comming back? please help me out.

    Read the article

  • route view for new IPs?

    - by Clear.Cache
    The route view method is not working for me telnet route-views.routeviews.org (logged in with user "rviews") route-viewsshow ip bgp 173.244.44.0 | inc 10464 route-viewsshow ip bgp 173.244.44.0 % Network not in table route-views Am I doing something wrong?

    Read the article

  • dlink arp spoofing prevention

    - by Wiploo
    someone can help me understanding arp spoofing prevention on dlink dgs-3100 (ftp://ftp2.dlink.com/PRODUCTS/DGS-3100-48P/REVA/DGS-3100-48P_MANUAL_3.60_EN.PDF). I'd like to protect my gateway MAC/IP from spoofing so I'have tryed to add a rule "IP: 192.168.1.1 MAC: aa-aa-aa-aa-aa-aa" flagging all the port of the switch as untrusted. When I apply the rule I lose connection to all pc attached to the switch. I certanly made some errors, but I can't understand what is wrong. Best Regards

    Read the article

  • Appropriate to Stateless Autoconfigure a Server?

    - by user31498
    I am setting up a network to support IPv6. Stateless Autoconfiguration seems to be the preferred way to get an IP address on an IPv6 network but is this the preferred way for a server? Other machines outside of the network are going to need to be able to talk to the server. Is it preferable to give the server a static IP address or is there something fancy that can be done with DNS to keep track of the server address?

    Read the article

  • How to know which program is using the WebClient service?

    - by sork
    Hello, I just found out by using TCPView that one of my svchost.exe had an http connection in "CLOSE_WAIT" to a strange ip address, although no other visible program was running. With the help of Process Explorer I discovered that this svchost was using the WebClient windows service. I'm wondering how I can figure out what program used WebClient to connect to this ip, in order to determine if it's malware.

    Read the article

  • Making to the DNS on two different VPNs play nice.

    - by NitroxDM
    Setup: I have two separate networks I need to connect to at the same time. VPN 1 PPTP IP : 192.168.2.0/24 DNS : 192.168.2.32; 192.168.2.34 (Windows 2003) Domain : old.com Forwarder : 192.168.2.1 (Gateway running DNS) DD-WRT VPN 2 OpenVPN using Routing -- I'm going to switch to bridging IP : 192.168.10.0/24 DNS : 192.168.10.10 (Windows 2008) Domain : xyz.dc Forwarder : 192.168.10.1 (Gateway running DNS) ClearOS When I'm connected I would like to resolve host names on both networks without fully qualifying them.

    Read the article

  • Remove key from known_hosts

    - by Adam Matan
    Hi, I have built several virtual machines during the last few weeks. The problem is, the .ssh/known_hosts gives me the Man in the middle warning. This happens because another fingerprint is associated with the virtual machine IP. In the .ssh/known_hosts file, however, I don't seem to find the record related to the IP, only two bizarre, key-like strings and "ssh-rsa". Any ideas how to remove the old key from known_hosts? Thanks, Udi

    Read the article

  • ESXi configuration

    - by Simone Falcini
    I just bought a dedicated server on online.net I have a public and a private ip. I installed esxi from their panel and I can connect successfully with my vsphere client. The problem is this: I want to create some instances and I want to give them different private ips. I also want to create some NAT rules to forward all users coming to my public ip port 80 to a specific instance. How can I do that? Thanks

    Read the article

  • Why is Windows 7 announcing itself as an IPv6 router?

    - by Paul
    I have a 6in4 ipv6 connection from a linux box to a broker. I use gogoc to establish the connection to the broker, and radvd to advertise the route to clients on the network. All this appears to work, the problem is that I have a Windows 7 machine on the same network, and it is advertising itself as a ipv6 router. Which it is not. This is output from radvdump: # # radvd configuration generated by radvdump 1.8.5 # based on Router Advertisement from [snip]:ea2 # received by interface eth0 # interface eth0 { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 0; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; AdvLinkMTU 1500; }; # End of interface definition # # radvd configuration generated by radvdump 1.8.5 # based on Router Advertisement from [snip]:1121 # received by interface eth0 # interface eth0 { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag off; AdvOtherConfigFlag off; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvLinkMTU 1280; AdvSourceLLAddress on; prefix [snip]::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition And I end up with two routes: $ ip -6 route [snip]::/64 dev eth0 proto kernel metric 256 expires 86117sec fe80::/64 dev eth0 proto kernel metric 256 default via [snip]:ea2 dev eth0 proto kernel metric 1024 expires 1492sec default via [snip]:1121 dev eth0 proto kernel metric 1024 expires 1506sec The ea2 route is to the Windows7 box. It doesn't have a router installed, and doesn't have any tun/tap interfaces. I can't see why it is doing this. I could disable ipv6 on it, but I want it to be a client, not a router. Update: The IP Helper service (Provides tunnel connectivity using IPv6 transition technologies (6to4, ISATAP, Port Proxy, and Teredo), and IP-HTTPS. If this service is stopped, the computer will not have the enhanced connectivity benefits that these technologies offer.) seems to be the culprit, as if it is stopped, I don't get the routes advertised. So my question is now more specifically "why is IP Helper announcing routes?".

    Read the article

  • Comcast SMC Port Forwarding Issue

    - by Zach Fedora
    I have a Comcast SMCD3G modem/router and I've been having issues getting the port to forward - When I check an online "open-port-checker" it says the port is forwarded/they can see the port on my IP. (1 Static IP is assigned to the modem) But when I try to access port 80 for example on a browser, it times out. Also when I try to remote desktop to the server (Windows Server 2008 R2) it doesn't work, yet canyouseeme.org says it is open. Any ideas as to what the problem could be?

    Read the article

  • Can't port forward ssh on Asus RT-NU56 wireless router

    - by Matt
    I cannot ssh in (using putty) when I use 10.0.1.31 as the address. database server - wired switch part of Asus wireless router - office LAN So basically, we want to ssh in to the database server from our computer on the wired office LAN. Asus router has an ip of 10.0.1.31 and database server has a static IP of 192.168.0.20 I set up port forwarding like this: ssh 22 192.168.0.20 22 BOTH Firewall is turned completely off. Any other settings I'm missing?

    Read the article

  • Why would an iPod Touch and PS3 respond to netdiscover as 0.0.0.0?

    - by Iszi
    Only slightly related to this question, because it was discovered in the same scan: Can someone explain how this happened? When running netdiscover on my home network, my iPod Touch (identified by DHCP-reserved IP address and MAC address) responded to both its own IP address on our 10.x.x.x subnet and to 0.0.0.0 also. Why would this have happened? EDIT: After letting netdiscover run awhile longer, it seems one of the PS3s on the network is also answering to 0.0.0.0 - why is this?

    Read the article

  • Why does localhost and 127.0.0.1 resolve to different locations on Mac OSC 10.8?

    - by Greg Wiley
    I set up a local server without MAMP, for various reasons. I used this tutorial: http://coolestguyplanettech.com/downtown/install-and-configure-apache-mysql-php-and-phpmyadmin-osx-108-mountain-lion I'm just wondering why the local IP and localhost resolve to two different locations. Right now the IP resolves to a Virtual Host I set up and the localhost resolves to the DocumentRoot established by httpd.conf

    Read the article

  • Server 2008, 2 NICs, 2 fixed IPs - big delays using internet

    - by user46055
    Hi geniuses I have an all in one Windows 2008 server, configured with AD/DHCP/DNS/RRAS - all set up with wizards and no specific tweaking. The server has 2 network adapters : one of which ("MyWAN") is plugged into our office's internet connection, the other ("MyLAN") is plugged into a local switch, which is also where all our desktops are connected. So this one server is doing everything. When first set up, MyLAN had a fixed IP of 192.168.2.1 and served the desktops with DHCP scope 192.168.2.50-99. It also told them to use 192.168.2.1 as DNS and gateway. MyWAN was setup to take its IP etc from DHCP, being handled by the building's router and ADSL modem etc. All desktops were setup to use DHCP. This all worked perfectly fine, until I recently changed MyWAN to have a static IP (I wanted to access it from home, and needed to give it a static IP to port map in the building's router). Things still work, but there is now a long delay when accessing the internet. The actual speed is as before when downloading, but there is a pause of 3-6 secs when connecting to new hosts (for example if I browse to slashdot from either a desktop or the server itself, it'll hang on connecting to slashdot.org, hang again on connecting to *.fsdn, *.google-analytics.com and all the other hosts referenced from the main page). If I ping slashdot.org from the server, I get the following : Pinging slashdot.org [216.34.181.45] with 32 bytes of data: Reply from 192.168.2.1: Destination host unreachable. Reply from 216.34.181.45: bytes=32 time=99ms TTL=239 Reply from 216.34.181.45: bytes=32 time=100ms TTL=239 Reply from 216.34.181.45: bytes=32 time=101ms TTL=239 Pinging anywhere external always seems to hit 192.168.2.1 first, which doesn't seem right. Trying tracert from the server gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 MYSERVER01.intranet [192.168.2.1] reports: Destination host unreachable Trying tracert from a desktop gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 <1 ms * <1 ms MYSERVER [192.168.2.1] 2 * * * Request timed out. 3 6 ms 6 ms 6 ms dsl-gw1.ge.mer.uk.webtapestry.net [217.151.111.17] 4 38 ms 239 ms 251 ms gw-router.ge.mer.uk.webtapestry.net [217.151.111.13] ...and then all is fine after that. I think that DNS is working fine because the domain names are getting translated to correct IPs immediately. DHCP seems to be okay? So perhaps it's something up with my RRAS setup - although I can't see any option during the setup wizard which I would have filled in differently. I've also tried changing the binding order of the two network connections, to prioritise MyWAN, but that doesn't seem to have done anything. Any idea what's up? Many thanks - Rob

    Read the article

  • Can't get DHCPd to assign IPs to unknown clients

    - by Jakobud
    I'm using Webmin to admin our DHCPd server. But I'm having a hard time getting it to assign IP addresses to unknown clients. The only way I can get it to assign an IP is to make sure a host is added to DHCPd as a host so that it gets a static-lease IP assigned to it. I thought "Allow Unknown Clients" was the key, but it still isn't assigning IPs to unknown clients. I have a pool setup so that the unknown clients should get an IP between 10.20.0.200 - 10.20.0.249. Here is the config file. What am I missing here? allow unknown-clients; # Primary DHCP server config authoritative; ddns-update-style none; failover peer "dhcp-failover" { primary; address 10.20.0.30; port 647; peer address 10.20.0.25; peer port 647; max-response-delay 60; max-unacked-updates 10; load balance max seconds 3; mclt 3600; split 128; } subnet 10.20.0.0 netmask 255.255.255.0 { allow unknown-clients; option subnet-mask 255.255.255.0; option broadcast-address 10.20.0.255; option routers 10.20.0.100; option domain-name "ourdomain.com"; option domain-name-servers 192.168.10.20; default-lease-time 86400; max-lease-time 86400; option ntp-servers 192.168.10.20; option time-offset -25200; pool { allow unknown-clients; failover peer "dhcp-failover"; max-lease-time 86400; range 10.20.0.200 10.20.0.249; deny dynamic bootp clients; } host Server-myserver { option host-name "whatever.ourdomain.com"; hardware ethernet 00:89:D4:35:4F:13; fixed-address 10.20.0.23; } }

    Read the article

  • Trunking between Juniper Ex3300 with Cisco Router

    - by danijuntak
    Hy Experts, Please tell how to create trunking with Juniper and Cisco. Cisco 2950 Juniper EX3300 Cisco 2621 I create VLAN 100,VLAN 200, VLAN 300 I have create trunk on juniper switch with : set interfaces ge-0/0/2 unit 0 family ethernet-switching vlan members root@switch# set interfaces ge-0/0/23 unit 0 family ethernet-switching port-mode trunk Now I want to telnet Juniper Switch from PC, but I don't know how to give IP address to Juniper switch and how to assign IP to vlan on Juniper switch.

    Read the article

  • What Iptables rules need I to forward a windows remote desktop connection?

    - by avastreg
    I have this situation: network mask. 255.255.255.0 router/gateway: Ubuntu server (only command line, no gui) with internal lan ip 192.168.0.2 and a dynamic dns on the external ip Windows pc on 192.168.0.1 with RDP (remote desktop connection) enabled on 3389 I want to forward the RDP service on the external address: how can i do that? What are the iptables rules I need to connect to my Windows pc from the outside world?

    Read the article

  • Do proxies really provide anonymity?

    - by Somebody still uses you MS-DOS
    Do web proxies really provide anonymity? I mean, without someone asking for logs in a web proxy server for who/when connected, is it impossible to know who was behind that IP address? I'm asking this because I heard somewhere that some technologies (like "flash") bypass personal IP information for requests or something like that. (I'm a noob in server configuration and concepts like DNS and proxies. Thanks!)

    Read the article

  • Port forwarding using a BT Home Hub 2.0 (Supplied to new BT Infinity Customers in the UK)

    - by Jasarien
    I don't usually have trouble with port forwarding, I've been able to do it successfully on a number of different routers, including Linksys, Belkin, Netgear and Apple (Time Capsule / Airport Extreme). So I'm quite confused here. I had been using my Apple Time Capsule as my router for a few years now, with several port mappings all working fine. But it died recently, so I've had to resort to using the BT Home Hub 2.0 that was supplied with my BT Infinity broadband subscription. The forwarding interface for the Home Hub is simplified for the most part, allowing you to select an application or game and assign it to a particular computer on the network which you choose from a list that the Home Hub has 'discovered'. My Mac Pro has a manually assigned static IP 192.168.1.4 and my router is static at 192.168.1. I have chosen SSH from the list of applications and assigned it to my Mac Pro (the only computer in the list currently). The Home Hub also has a feature to keep a DNS service updated, and I have set it to keep my external IP address updated on my hostname. This is how I had it setup in the past with other routers and not had trouble before. I am able to ping my hostname (and external IP) from outside the network and get a response. But when I try to connect using SSH, the connection times out. The Home Hub also has "Firewall settings". The currently selected setting is: Default: Allow all outgoing connections and block all incoming traffic. Games and application sharing is allowed. But I've tried changing it to: Disabled: All traffic is allowed to pass through your BT Home Hub to your devices. Note: you’ll still need to use the games and application sharing feature to make sure that certain applications work properly. And the connection still times out... So frustrating. The OS X firewall on my Mac is disabled, so I don't think that's in the way. I have tried setting the port forwarding manually, instead of relying on the preset "SSH" option (incase it's not using the port I expect). So I set up my own "application" (as the Home Hub calls it) and forwarded external port 22 TCP to internal port 22 TCP to 192.168.1.4 - but that just gives the same result - unable to connect. Next, with the router's firewall disabled and OS X's firewall disabled, I ran the Shields Up test (https://www.grc.com/x/ne.dll?bh0bkyd2) and the result was that all my service ports (0 - 1055) are in 'Stealth' mode. I.e. nothing even exists at my IP as far as any outsider is concerned... Strange. The only thing that seems to work is setting my Mac Pro as the DMZ - which I don't want to do for obvious reasons. Any help with this would be extremely appreciated, thanks.

    Read the article

  • Voice on 4G Technologies such as LTE and WiMAX?

    - by Vaibhav Bajpai
    I understand that LTE and WiMAX are IP-based technologies that do NOT have a voice component unlike the current 3G technologies. So is it like, voice calls in 4G would be completely driven on top of IP? Wouldn't this break backward compatibility with existing 3G technologies? Is this why 4G is taking it took long to take ubiquitous availability?

    Read the article

  • Xen Server Guest Network configuration?

    - by GeekTantra
    I am trying to install Ubuntu Server as a domU (Guest) on Citrix XenServer. Everything works fine but I am not able to access the internet from the guest. Is there any specific thing that I need to do to configure the network for the Guest. I have two NICs, 1 has an external IP and the other has an internal IP.

    Read the article

< Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >