Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 169/343 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

  • Network latency and speed of light

    - by James
    This was kinda of covered by the following Is minimum latency fixed by the speed of light? , but i would like to add the follow up a bit. The scenario is as follows; we have two opposing sites one on the West Coast of the US and one in Ireland. The customer is in central Europe, and has requested a latency test. Ireland gives responses of ~65-70ms. However the West Coast guys claim to be faster with a response of 60ms. Now a quick check says that light in fiber would take about 42ms to make the trip to the States and 8.5ms to Ireland. So obviously this is a single hop and does not include routers, switches, firewalls, protocol overhead etc. Would I be right to call BS on their figures? As a final note I tested a ping to Google IP address that was allegedly on the west coast from a site that covered a similar distance and was amazed to get a response time of 20ms. Suggesting ICMP packets that travel twice the speed of light. So A) what am I missing B) Am I right to suspect shenanigans? UPDATE: Guys thanks so far for your help and I have been reading various previous questions on this. About 5 years I had an issue where the hop from the UK to Ireland added 10ms of latency no matter what we did. In the end I moved the servers; So imagine my surprise when I have guys that claim they are 5ms faster with a transatlantic trip. So again should I call BS? Oh and assume both sites are normal mortals that don't have access to Google magical routing, warp dives or flux capacitors. :)

    Read the article

  • How can I restrict SSH access when the source IP is dynamic

    - by Supratik
    Hi I want to protect SSH access to our live web server from all IP's except our office static IP. There are some employees who connects to this live server from their dynamic IP's. So, it is not always possible for me to change in the iptables rule in live server whenever the dynamic IP of the employee changes. I tried to put them in office VPN and allowed only SSH access from office IP but the office connection is slow in compared to our employee's private internet connection, moreover it adds an extra overhead to our office network. Is there any way I can solve this problem ?

    Read the article

  • Do all the network cards use the same frequency to send signals to wire?

    - by smwikipedia
    I am comparing my cable TV wire to my network wire. In a TV cable wire, different frequencies are used by different TV channels. And since a certain channel use a fixed frequency, I think the only left way to represent different signal is with the carrier wave's amplitude. But what about the network wire? For all the network cards with the same type, do they also use different frequencies to send signals just like TV cable? I vaguely remember that they use frequency adjustment to represent signals. So the frequency should not be a fixed one. So how did all the network cards that sharing the same medium differentiate their own signal from others?

    Read the article

  • Should I Upgrade My Old Wireless Router?

    - by lyngbym
    I have an old wireless router, and I mean stone age old (5 years). There is nothing wrong technically with the router, it serves my wireless needs at home but it is really darn old. A search on Belkin's site for F5D7230-4 actually turns up a different old model so I scrounged up this old review for you to get a sense of what I'm running: http://www.pcmag.com/article2/0,2817,1572451,00.asp. Is there a valid security reason to replace this router in 2009? Google searches have turned up a few security threats to it and Belkin hasn't released new firmeware in years for it. I am starting to think I should replace it mainly because its NAT is about the only thing protecting me from the outside world. Buying a new wireless router is a boring way to spend money since it just sits on a shelf doing its job. Thoughts?

    Read the article

  • Servers behind load balancer

    - by Tom
    We have a CISCO hardware load balancer with two web servers behind it. We'd like to force some URLs to only be served by one of the machines. Firstly, is the job of the load balancer? or would a better approach be create a subdomain such as http://assets.example.com which would be automatically be routed to one of the servers?

    Read the article

  • Setting Up My Home Network

    - by Skizz
    I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

    Read the article

  • Web browsing is fast, but downloads are slow

    - by Ricket
    I work for a company on my university's campus, helping with general IT problems and some web development. But lately there has been a problem that has me and my boss completely stumped. We, plus one contractor, make up the entire IT department, so I'm reaching out to you for help. All around the office, we have wall jacks. These collect in a closet down the hall and all plug into a switch. This switch, along with our individual server jacks, plugs into another switch, and that switch plugs into our firewall hardware. Then the firewall is connected out to our campus network. Our campus internet is, well, very fast. I don't know exactly the terms, tiers, etc., but we have thousands of students and downloads can run as fast as 10 MB/s at night; uploads are sometimes even faster. I think we're practically ISP level. In short, I have a lot of faith that it is not the campus side of things that is causing a problem, combined with other evidence I'll mention in a moment. So our symptoms: web browsing is fast. Web pages, images, etc. load instantly. No problems there. But then when I go to download something, the download starts fast but very quickly (a matter of seconds) drops to nearly 0. Often it will actually drop to 0 and time out. This happens with even very small files, 1 MB or less. It smells to me like a QoS sort of thing. I'm not entirely sure, and I wanted to get your opinions first. My boss is hesitant to touch our firewall, much less let me touch it, and it was set up and is managed by a consultant remotely. These problems don't seem tied to a time of the day. I've tried downloads after 5:00 and still the same thing happens. From my desk, I can turn on my wireless adapter and pick up the campus wireless access point. If I unplug ethernet and connect to it, downloads are fast. This adds to my suspicion that it's limited to our company network. Also, a number of weeks ago the consultant upgraded our firewall firmware. Suddenly everything was very fast. I tested with downloads from Sun and speedtest.net and things were blazing fast, as they should be with our campus internet! It was wonderful, and I figured the slow speeds were an old firmware bug. In a matter of days, things steadily declined until they were back to the old symptoms. Oh, and we have antivirus installed on every computer, and we keep it up to date. Though I suppose the possibility is still there that someone could have spyware which is bogging down our internet, in which case what is the easiest/best way to find this out? (maybe this should go in a separate question) Thank you for your patience in reading all of this. Do you have any ideas as to what I can try? Is this something that you've experienced before? What sort of tools or methods can I use to try and diagnose the problem? P.S. everything here is Windows. Windows Server 2003 and 2008 on our servers, and Windows XP on employees' machines. Update: We are submitting a ticket to the university to just take a look and see if they see anything unusual and/or can suggestion methods for us to try and pinpoint our problem. Hopefully they'll be helpful! I'll update this to let you know what goes on. Update again: We found a hub (yes, a HUB) right between our campus connection and our firewall. It had only those two ethernet cables plugged into it, nothing else. After removing the hub, our speeds have jumped up to several mbps. However in talking with the campus, we got them to run a gigabit line to our firewall in place of the 100mbps line. As of friday, we are at about 65 mbps up and down (according to speedtest.net at 8am)!! Go NC State!!

    Read the article

  • Facebook doesn't work on computer, but work on mobile device, both use the same router

    - by sasa
    I have a very strange problem and I'm thinking that can be problem with dns or something similar, but not sure and don't know how to solve. My computer is connected to router and every site works fine except facebook (Chrome and Firefox). Chrome shows "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." But, on mobile device witch is connected to the same router facebook works fine (Fb application and Delphin browser). Pinging facebook works fine. Clearing cookies and cache didn't help. Also, I performed antivirus and antimalware scan and there is nothing. What can be a problem? Update: I'm also connect notebook on that wifi router, and on it works fine. nslookup facebook.com Server: UnKnown Address: 192.168.1.1 Non-authoritative answer: Name: facebook.com Addresses: 2a03:2880:2110:3f01:face:b00c:: 2a03:2880:10:1f02:face:b00c:0:25 2a03:2880:10:8f01:face:b00c:0:25 69.171.224.37 69.171.229.11 69.171.242.11 66.220.149.11 66.220.158.11

    Read the article

  • Unexpected network traffic?

    - by robwalker
    My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

    Read the article

  • PTR Record for host in VLSM subnet

    - by paradroid
    I understand that this is the way a PTR record would be made on a Class A subnet (10.100.250.100 255.0.0.0) dnscmd /RecordAdd 10.in-addr.arpa. 100.250.100 PTR host.domain.tld To clarify the syntax, this is what it should be for a Class C subnet (192.168.1.100 255.255.255.0) dnscmd /RecordAdd 1.168.192.in-addr.arpa. 100 PTR host.domain.tld Is that right? Now how do I do this for a host with the IP address 172.31.111.210 on a 172.31.111.192/26 network? I'm not sure how to do this with a classless subnet mask.

    Read the article

  • In TCP/IP terms, how does a download speed limiter in an office work?

    - by TessellatingHeckler
    Assume an office of people, they want to limit HTTP downloads to a max of 40% bandwidth of their internet connection speed so that it doesn't block other traffic. We say "it's not supported in your firewall", and they say the inevitable line "we used to be able to do it with our Netgear/DLink/DrayTek". Thinking about it, a download is like this: HTTP GET request Server sends file data as TCP packets Client acknowledges receipt of TCP packets Repeat until download finished. The speed is determined by how fast the server sends data to you, and how fast you acknowledge it. So, to limit download speed, you have two choices: 1) Instruct the server to send data to you more slowly - and I don't think there's any protocol feature to request that in TCP or HTTP. 2) Acknowledge packets more slowly by limiting your upload speed, and also ruin your upload speed. How do devices do this limiting? Is there a standard way?

    Read the article

  • Why does 1GBit card have output limited to 80 MiB ?

    - by Gallus
    I'm trying to utilize maximal bandwidth provided by my 1GiB network card, but it's always limited to 80MiB (real megabytes). What can be the reason? Card description (lshw output): description: Ethernet interface product: DGE-530T Gigabit Ethernet Adapter (rev 11) vendor: D-Link System Inc physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 11 serial: 00:22:b0:68:70:41 size: 1GB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation The card is placed in following PCI slot: *-pci:2 description: PCI bridge product: 82801 PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: 92 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list The PCI isn't any PCI Express right? It's a legacy PCI slot? So maybe this is the reason? OS is a linux.

    Read the article

  • Troubleshooting wireless client-bridged networks between two DD-WRT routers?

    - by KronoS
    I recently purchased a Buffalo N600 wireless router which came with DD-WRT pre-installed. I want to take my old wireless router a Linksys WRT54GL, also with DD-WRT pre-installed, and use it as a wireless bridge for my HTPC and Blu-Ray Player in the other room. I other words, I'm trying to connect to WIRED networks via the wireless on the routers. I followed eactly the instruction from DD-WRT's manual for 'Client Bridged' however I'm still not able to connect to two routers correctly, when the encryption is enabled (WPA2-Personal Mixed) however I am able to connect the two routers when there is NO encryption. I've checked, double checked, and triple checked that EVERYTHING is the same on BOTH routers: Routers 1 & 2 Encryption: WPA2-Personal Mixed Wireless Mode: G-Only Wireless Channel: 6 Subnet Mask: 255.255.255.0 Subnet: 192.168.1.0/254 SSID: Krono$ Primary Router #1 (Buffalo N600) IP Address: 192.168.1.1 Firewall: Enables w/ defaults DCHP: Enabled as DHCP Server Secondary Router #2 (Linksys WRT54GL) IP Address: 192.168.1.2 Firewall: Disabled as per DD-WRT instructions I'm looking for any configurations that I may have missed, or settings that may need to happen in order for this work.

    Read the article

  • Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

    - by Linux Guy
    I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

    Read the article

  • pfsense CARP - wan failure on firewall

    - by eldblz
    I have recently configured 2 firewall (on 2 DELL PowerEdge R210II with ESXI 5.1) with pfsense. We have several LANs and 2 WANs. Everything is running fine but i have a strange behavior: i can access internet from alla LANs but not from the firewall (itself). For example the firewall cannot retrive package information or if i setup a gatway monitor ip (like google 8.8.8.8 ) this fails. These are the screenshots of firewall configuration: http://imgur.com/a/LNuMz#0 ATM i kept firewall rules to minimum to avoid problem or conflicts. Any ideas how to solve the problem? Thank you in advance.

    Read the article

  • Translating debian network configuration to gentoo

    - by thpetrus
    I just got rid off Debian on my VPS (OpenVZ) and installed Gentoo on it, however it is a plain Gentoo image without further configuration, i.e. no working network. I'm not familiar with Debian and coulnd't figure out how to get the network set up, these are the debian network files /etc/network/interfaces: auto venet0 iface venet0 inet manual up ifconfig venet0 up up ifconfig venet0 127.0.0.2 up route add default dev venet0 down route del default dev venet0 down ifconfig venet0 down iface venet0 inet6 manual up ifconfig venet0 add ipv6addr/128 down ifconfig venet0 del ipv6addr/128 up route -A inet6 add default dev venet0 down route -A inet6 del default dev venet0 auto venet0:0 iface venet0:0 inet static address external_ip netmask 255.255.255.255 auto venet0:1 iface venet0:1 inet static address internal_ip netmask 255.255.255.255 Please note that external_ip, internal_ip and ipv6addr are placeholders. I copied the /etc/resolv.conf, know the gateway_ip and also have another ouput of ifconfig, if necessary. This is what I came up with, /etc/conf.d/net: config_venet0="127.0.0.2 netmask 255.255.255.255 brd 0.0.0.0" config_venet0:0="external_ip netmask 255.255.255.255 brd 0.0.0.0" route_venet0:0="default via gateway_ip" config_venet0:1="internal_ip netmask 255.255.255.255 brd 0.0.0.0" Broadcast IP is taken from ifconfig debian output - however it doesn't work. A symbolic link net.venet0:0 -> net.lo in /etc/init.d/ was created and I added net.venet0:0 to the boot runlevel.

    Read the article

  • Generate a limited amount of random network traffic between 2 hosts

    - by Andrew S
    I'm trying to find a utility that will allow me to generate a constant flow of random network traffic at a specified rate between 2 hosts. The utility needs to run on Windows and OSX. I've tried iperf but it seems to be more oriented toward short-term testing/statistics and it really taxes the CPU even at slower rates. I want something that will generate traffic for a few weeks at say 10Mbps while I use other tools to monitor the impact of that level of traffic on the network.

    Read the article

  • Need help using a super scope

    - by Vdub
    I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

    Read the article

  • Sharing a wifi connection between different user profiles on Windows XP

    - by crowne
    I've set-up two separate user profiles on an old laptop running Windows-XP, and noted the following strange behaviour. When the wireless network is setup using WEP both user profiles can connect to the internet and I can switch between user profiles, without network connectivity issues. However when I changed the wireless security to WPA2, the first user to connect gets access to the internet, when switching to the second profile the connection fails. The behaviour is the same regardless of which of the two profiles logs on first. I also tried this with one user with admin rights and one without, and got the same result. I'm not too concerned about a fix for this other than forcing the users to log-off when sharing the laptop, but I'd be interested to know if anyone can corroborate my findings. The network config was done using Intel® PROSet/Wireless.

    Read the article

  • Configure TCP/IP to use DHCP and a Static IP Address at the Same Time

    - by Tiago
    My computer is configured to obtain a IP address automatically using DHCP. It only has one network adapter. How to configure an additional static IP address? I found a tutorial for Windows XP, but the procedure didn't work for Windows 7. Is it possible to configure two IP addresses on Windows 7, one being static e another being dynamic? How? The dynamic address I got now is 10.17.11.162. The static IP is 10.17.30.19. The network mask is the same: 255.255.224.0. Both work independently, but I don't know how to use both at the same time.

    Read the article

  • Can't connect to YouTube from specific network

    - by Tyilo
    Using my current network, I am unable to connect to http://www.youtube.com/. It doesn't matter what browser I use or if I use a cli-command (wget, curl). Error in Google Chrome: Oops! Google Chrome could not connect to www.youtube.com Error using curl: curl: (7) couldn't connect to host If I use nslookup to get the IP-address of YouTube, I get 173.194.32.32. If I go to http://173.194.32.32/ in my browser it can connect, but as Google is probably checking the Host HTTP-header, it shows Google's frontpage instead. There is no blocked websites on the router and other devices on the network seems to work. My computer only has this problem on this specific network. I am using Mac OS X 10.8.2 on a MacBook (mid 2009).

    Read the article

  • Disable dhcp client over one interface

    - by Lopoc
    Hi to all I'm encountering a problem on a sever with two ethernet interfaces(etho and eth1), it runs linux-ubuntu-server. I need eth1 not make any dhcp request, becouse I need it to be only a listening interface, obviusly I need eth0 running normally. So how can i disable any dhcpclient ation over eth1? thank in advance.

    Read the article

  • Managing two internet connections in Windows XP, with different applications using different connections

    - by user932867535
    I have two internet connections, one has limited data but is fast, the other has unlimited data but is slow. What am trying to do is assign the unlimited data connection to the application which is downloading a large file, while surfing the net (using Firefox) with the other, faster connection. I tried connecting both connections, but every time I do that, all the applications just jump from the slower connection to the faster one. Is there any way in which I could achieve what I am looking for?

    Read the article

  • how to create a 802.11n wireless network between laptops and asus n-13 wireless adapter ?

    - by xpugur
    I have a asus usb n-13 wireless adapter and 3 laptops in a home we try to create a network witn 802.11n standards but failed each time laptops have intel 5100 agn. We try to create network with wpa-2 personal encryption that also fails(couldn't connect) but with wep encryption connects but with 802.11g standard... so do you know how to create a 802.11N based network? ... thank you...

    Read the article

  • Network card/driver stops under heavy load

    - by Uwe Keim
    Since about approx. 2 month, I do have the following issue with my approx. 1 year old development machine (Windows 7, 64 bit): When doing network intensive operations, like e.g. executing some SQL script on a remote SQL server to select or update 1000 of records, the network card stops working. I.e. suddenly, No network connection is present anymore. No internet, no local connection, simply nothing. The only resolution so far I found is to disable my network card and then simply enable it back, like in the following screenshots: 1.) Click "Deactivate" 2.) Click "Activate" (German screenshots only, sorry) Now this is an acceptable solution to work around this issue, but I would love to have this fixed, since it suddenly stops me from working when I'm connected remotely via VPN/RDP on my machine (Win7 64bit). So my question is: Could you imagine a possible cause for this issue and give some hints how to hunt/resolve it? I could imagine that this is a driver issue, a hardware issue or even some kind of background software issue like a software firewall or a virus scanner.

    Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >