Search Results

Search found 5864 results on 235 pages for 'secure gateway'.

Page 171/235 | < Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >

• OpenVPN (Tunnelblick) Suddenly Dropping Constantly

  - by Jeremy Privett

  I've been using Tunnelblick on my Mac for OpenVPN for about a year now. All of a sudden, this morning, it decided that it was going to take a nasty turn for the worse with no explanation. Here are the symptoms I'm seeing: I can connect to the VPN fine, initially. After about 2 - 5 minutes of no interruption, the connection suddenly dies. I can still see the VPN route using netstat -rn, and Tunnelblick believes it's still connected. No VPN traffic can go through and I can't even ping the VPN gateway. Eventually, Tunnelblick will catch on that the connection has died (usually about 5 - 10 minutes later) and shoot itself to restart and then the cycle starts over again. I've tried everything I can think of to figure this one out. I've completely flushed my system by rebooting and removing Tunnelblick and all traces of OpenVPN from my system and re-installing from scratch. No dice, same problem. I'm at my wits end, because I desperately need to get this fixed as the VPN is required for me to be able to do my job. Any ideas you have would be greatly appreciated.

  Read the article

• OpenVPN IPV6 Tunnel Radvd

  - by Arenstar

  Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

  Read the article

• Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

  - by Kyle Brandt

  By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

  Read the article

• filter / directing URLs coming onto a network

  - by Jon

  Hi all, I an not sure if this is possible or not but what i would like to do is as follows: I have one IP address (dynamic using zoneedit.com to keep it upto date). I have one webserver running my main site which is an Ubuntu machine running Apache. I also have a windows 2008 server running another site. Just to confuse things I also run part of my Apache site on the windows server, currently using proxypassreverse to get the information from it. So it looks something like this: IP 1.2.3.4 maps to mydomain.com as well as myotherdomain.com All requests that come into port 80 are forwarded to the Apache box and I use Virtualhost settings to proxy the windows sites where needed. so mydomain.com is an Apache site mydomain.com/mywindowssection is the Apache server using proxypassreverse to get part of the site from the Windows server myotherdomain.com uses Apache and proxypassreverse to get the whole site. What I would like to be able to do is forward all http requests that come into my network to one machine that figures out who should be serving that content. so: mydomain.com would go to the Apache machine myotherdomain.com would go the windows machine. I am just in the process of setting up an Astaro gateway (never done this before so taking a while to configure) as my firewall, dns, dhcp etc, don't know if this can handle it. I have the capacity to run a VM on the network if a seperate box would be needed for this process as well. Thanks for any and all feedback. Jon

  Read the article

• management network to a network port for additional ones munin and monit

  - by paolo

  management network to a network port for additional ones munin and monit I want to build a separate Netzwek for server management. I have several network cards a linux / debian / ubuntu with computer. Set both network cards sin in the /etc/network/interfaces. # The primary network interface #allow-hotplug eth0 #iface eth0 inet dhcp auto eth0 iface eth0 inet static address 10.0.0.240 netmast 255.255.255.0 network 10.0.0.0 brodacast 10.0.0.255 gateway 10.0.0.254 auto eth1 iface eth1 inet static address 10.0.10.240 netmast 255.255.255.0 network 10.0.10.0 brodacast 10.0.10.255 post-up ip route add 10.0.0.0/24 dev eth0 src 10.0.0.240 table eth0-WAN post-up ip route add default via 10.0.0.254 table eth0-WAN post-up ip route add 10.0.10.0/24 dev eth1 src 10.0.10.240 table eth1-LAN post-up ip route add default via 10.0.10.200 table eth1-LAN post-up ip rule add from 10.0.0.240 table eth0-WAN post-up ip rule add from 10.0.10.240 table eth1-LAN still i adjusted / etc/iproute2/rt_tables and following routes set up in the /etc/network/interfaces I want to have both applications and the network interface separately as munin and monit only on eth1 and not have to eth0. it goes to the reboot but sometimes not always. # Traceroute-i eth1 10.0.10.200 not go what am I doing wrong?

  Read the article

• Which MAC address is the right one?

  - by Paul Dinh

  Result by 'getmac': C:\>getmac Physical Address Transport Name =================== ========================================================== 72-03-C6-48-59-34 \Device\Tcpip_{8AEB3263-18C4-449E-A80F-BC2541DDC2A9} 00-21-9B-D5-6F-EE \Device\Tcpip_{C2F9CE19-D68F-4105-9766-45CBE6D82331} 00-22-68-D2-9B-F7 \Device\Tcpip_{A2701130-9221-43FE-8F14-7B1114F84DC3} Result by 'ipconfig /all': C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : xps-m1530 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Mixed IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1395 WLAN Mini-Card Physical Address. . . . . . . . . : 00-22-68-D2-9B-F7 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Autoconfiguration IP Address. . . : 169.254.246.4 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8040 PCI-E Fast Eth ernet Controller Physical Address. . . . . . . . . : 00-21-9B-D5-6F-EE Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.112 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 8.8.8.8 8.8.4.4 Lease Obtained. . . . . . . . . . : 01 November 2012 9:00:36 AM Lease Expires . . . . . . . . . . : 04 November 2012 9:00:36 AM There is a MAC address on the back of my laptop, but the sticker is no longer there. So I use the 'getmac' command to get the MAC addresses. But which address shown by 'getmac' above is the one matching the MAC in the sticker on the back of my laptop? Or am I mistaken something? 00-21-... is the ethernet adapter, 00-22-... is the wireless adapter, and 72-03-... is what?

  Read the article

• Cannot connect to windows server by name over vpn connection

  - by ErocM

  I have a rented dedicated windows server on a public ip that is acting as a SQL Server and VPN server. I need to connect to this server via computer name to get replication in place. I cannot use an ip address due to this issue: So, due to this, we are going the VPN route. That is my primary issue: After I am connected to this server's vpn, I can connect to SQL Server using the ip address but I cannot connect by the computer's name as you can see below... Right now, there is no hardware firewall on it since I had it removed to test this issue. I am running Windows 2008 Enterprise Server as the VPN server. I am not sure if the route print will help any from the workstation trying to connect but here is the info: IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.0.0.0 10.0.0.1 10.0.0.2 21 10.0.0.2 255.255.255.255 On-link 10.0.0.2 276 Any other info needed? Thanks for the help! ========= CLARIFICATION ON A FEW THINGS #1 ========= This is the server's info: This is the workstation that is trying to connect: I connect to the server via "Control Panel\Network and Internet\Network and Sharing Center\Connect or Disconnect" You can see here that I am connected: ========= CLARIFICATION ON A FEW THINGS #2 ========= I've tried to connect directly to the Sql Server as I did above but with the computers name and I couldn't get to it. Here I am trying to net view it from the workstation and it couldn't find it:

  Read the article

• Bridging Wireless and Wired Interfaces in Linux

  - by The Daemons Advocate

  My network setup is something like: Wireless Router <---> Netbook <---> Ubuntu Desktop ...or, more verbosely (with interfaces): Wireless Router <--(wireless)--> (eth2) Ubuntu Netbook Ubuntu Netbook (eth0) <---(wired)----> (eth0) Ubuntu Desktop In a perfect world, I'd have the desktop wired, but weird circumstances combined with my wanting to understand more about networking in linux make me want to figure out how to bridge these two devices. A bit of googling has given me this example using bridge-utils, and here's how I'm (failing) to setup the bridge (on the netbook): sudo -i ifconfig eth0 0.0.0.0 ifconfig eth2 0.0.0.0 brctl addbr bridget brctl addif bridget eth0 brctl addif bridget eth2 ifconfig bridget up ...then, trying to make sure that the netbook can still get on the internets... route add default gateway 192.168.2.1 dhclient bridget What happens after this is that the dhclient command above (netbook) doesn't get served an IP, and the Desktop, if I run dhclient, it doesn't get served an IP. Some weird considerations might be that I'm running the Network Manager Applet that comes with Ubuntu. While I'm sure I can get a command line wireless configuration setup, it's a bit complex. Can someone give me a shout as to where I'm going wrong? I'd also like to note another related question titled 'Bridging my laptop’s wireless and wired adaptors', however the setup is different to mine.

  Read the article

• Windows 2012 RDS Temporary profile for Administrator

  - by Fabio

  I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

  Read the article

• Private staff network within public network

  - by pianohacker

  I'm the sysadmin at a small public library. Since I got here a few years ago, I've been trying to set up the network in a secure and simple way. Security is a little tricky; the staff and patron networks need to be separated, for security reasons. Even if I further isolated the public wireless, I'd still rather not trust the security of our public computers. However, the two networks also need to communicate; even if I set up enough VMs so they didn't share any servers, they need to use the same two printers at the very least. Currently, I'm solving this with some jerry-rigged commodity equipment. The patron network, linked together by switches, has a Windows server connected to it for DNS and DHCP and a DSL modem for a gateway. Also on the patron network is the WAN side of a Linksys router. This router is the "top" of the staff network, and has the same Windows server connected on a different port, providing DNS and DHCP, and another, faster DSL modem (separate connections are very useful, especially as we heavily depend on some cloud-hosted software). tl;dr: We have a public network, and a NATed staff network within it. My question is; is this really the best way to do this? The right equipment would likely make my job easier, but anything with more than four ports and even rudimentary management quickly becomes a heavy hit on our budget. (My original question was about an ungodly frustrating DHCP routing issue, but I thought I'd ask whether my network was broken rather than asking about the DHCP problem and being told my network was broken.)

  Read the article

• Need help using a super scope

  - by Vdub

  I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

  Read the article

• Issue with multiple bridging for KVM hosts

  - by Henry-Nicolas Tourneur

  I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

  Read the article

• Email flow problem in Exchange 2003

  - by Hugo Garcia

  Hello colleagues, I have a problem whit some emails that are not being delivered to the user inbox. The SMTP server on the DMZ that receives email from the internet is a Symantec Brigthmail Gateway, this server reports that the message was delivered normally to the exchange server: The DMZ server forwars the incoming mail to the exchange server that is on the LAN segment, and the message tracking on the exchange server reports the email being submited to the advanced queue: I have done severals searches on google, without any luck. have any one of you guys experienced similar problems? Any help or pointers would be very appreciated. as requested, here is a transcript of a smtp session: helo 250 mail2.XXXXXXXXXXXXXXXX.XXX.XX Hello [192.168.9.6] MAIL FROM: [email protected] RCPT TO: [email protected] DATA Subject: Mensaje de Prueba Test . 250 2.1.0 [email protected] OK 250 2.1.5 [email protected] 354 Start mail input; end with <CRLF>.<CRLF> 250 2.6.0 <'[email protected]> Queued mail for delivery

  Read the article

• OpenVPN Keeps Crashing

  - by Frank Thornton

  Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28523 [vpntest] Peer Connection Initiated with [AF_INET]<MY_IP>:28523 Oct 20 21:00:44 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 MULTI_sva: pool returned IPv4=10.8.0.6, IPv6=(Not enabled) Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1576', remote='link-mtu 1376' Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1532', remote='tun-mtu 1332' Oct 20 21:00:45 sb1 openvpn[2082]: <MY_IP>:28522 [vpntest2] Peer Connection Initiated with [AF_INET]<MY_IP>:28522 Oct 20 21:00:45 sb1 openvpn[2082]: vpntest2/<MY_IP>:28522 MULTI_sva: pool returned IPv4=10.8.0.10, IPv6=(Not enabled) Oct 20 21:00:46 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 send_push_reply(): safe_cap=940 Client File: client dev tun proto tcp remote <IP> 443 resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1410 persist-key persist-tun auth-user-pass comp-lzo SERVER: port 443 #- port proto tcp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 reneg-sec 0 #mtu-disc yes mssfix 1410 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /etc/openvpn/openvpn-auth-pam.so /etc/pam.d/login #plugin /usr/share/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Comment this line if you are using FreeRADIUS #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment this line if you are using FreeRADIUS client-to-client client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 3 30 comp-lzo persist-key persist-tun What is causing the VPN to keep dropping the connection and then reconnecting?

  Read the article

• How is it possible that I can do a host lookup but not a curl?

  - by Daniel Quinn

  Has anyone ever seen this before? Note that this happens not only with google.com, but with every domain I try. It's a wireless connection (WEP), but I'm not sure how that would be relevant: $ curl -v google.com # This takes about 60s to return * getaddrinfo(3) failed for google.com:80 * Couldn't resolve host 'google.com' * Closing connection #0 curl: (6) Couldn't resolve host 'google.com' $ host google.com google.com has address 209.85.148.106 google.com has address 209.85.148.147 google.com has address 209.85.148.99 google.com has address 209.85.148.103 google.com has address 209.85.148.104 google.com has address 209.85.148.105 google.com mail is handled by 30 alt2.aspmx.l.google.com. google.com mail is handled by 40 alt3.aspmx.l.google.com. google.com mail is handled by 50 alt4.aspmx.l.google.com. google.com mail is handled by 10 aspmx.l.google.com. google.com mail is handled by 20 alt1.aspmx.l.google.com. $ cat /etc/resolv.conf # Generated by NetworkManager nameserver 192.168.1.201 $ cat /etc/hosts 127.0.0.1 localhost ::1 localhost $ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.1.254 0.0.0.0 UG 0 0 0 wlan0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Disconnect from PHP after output generated

  - by Oli

  I have a LEMP stack. Nginx sitting in front of PHP-FPM. Because some of the sites are heavy and there's OPCode caching, PHP is set up so that there are only 5 child processes running. The aim being that each child can deal with any request in less than half-a-second and then move onto the next request. One problem I've found is that if it's a big chunk of HTML that's getting sent out, and the user has a slow connection, that PHP thread stays occupied until they've finished downloading. Because of my current setup, I have a pretty unforgiving timeout inside PHP where the script is killed after 20 seconds. This is to make sure everybody gets a turn but on a slow connection, this can mean the user gets cut off with a 504 Gateway timeout. I was wondering if there was some sort of buffer solution that I could implement within or just behind Nginx that sent the request through and then... well... buffered the content into its own cache and feed that onto the client as and when they could download it. The aim being that the underlying PHP thread can be freed up. What I'm asking for doesn't have to be PHP-specific. Anything that deals with FastCGI, or even any Nginx-upstream might have a similar issue to this.

  Read the article

• Juniper SSG 5 VPN

  - by Ethabelle

  I have a host who set up our Juniper SSG 5 VPN with Firmware version-6.2.0r5.0 I've been trying to set up VPN on it using this guide: http://kb.juniper.net/InfoCenter/index?page=content&id=KB4094 I've followed the steps and on my Mac, whenever I try to connect using L2TP over IPSec I get the following error; Summary of Steps: Create User (give them L2TP auth ability), Create Group, Place User in Group, Create VPN Gateway, Create VPN, create IP Pool, change default L2TP settings, create Untrust Trust Policy. The L2TP-VPN server did not respond. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I looked in my Firewall's logs, but I don't even see anything under Reports Logs Events. I'm.. obviously missing something, I just don't know what I'm missing at this point. I'm just starting networking and this is sort of Step 101 and I'm getting annoyed and just want to throw up OpenVPN, but I've read that has problems with Juniper Firewalls. Hooray.

  Read the article

• AWS VPC ELB vs. Custom Load Balancing

  - by CP510

  So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

  Read the article

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• LogMeIn style remote access to NAS drive

  - by Mere Development

  I've been asked to setup some remote access to a NAS drive. The NAS drive will sit on a VLAN inside a network that uses a Cisco 891 IS router as gateway. The charity have no SSL-VPN licenses for the Cisco. At present there are no open ports or services on the Cisco itself and ideally we would like to keep it that way for a while, hence the request for a LogMeIn style service that's initiated from inside. We need multiple user access, about 10 max. Using LogMeIn on a machine connected to the NAS would only provide screen sharing I believe, and no concurrent connections (could be wrong?) The end users need to be able to read and write files to the NAS from Mac's and PC's around the globe. Read-only access from Mobile devices would be a bonus but not absolutely necessary. This is for a charity, non-commercial, but they are willing to spend if necessary. Cisco config knowledge is at a minimum so if I can avoid upsetting that delicate device I'll be happy :) Anyone have any clever ideas? I can provide more information on request. Thanks, Ben

  Read the article

• How to connect a Win XP PC and Win 7 PC with a Linksys WRT54G Router to a PPPOE connection ?

  - by ChristianM

  I have two PCs and a WRT56G Router. My provider is a PPPOE connection (username and password). I can connect my Windows 7 easily. Even if I choose Auto or PPPOE on the router's configuration. Maybe because this one had the connection in the first place with the username and password set up. But I can't connect the Windows XP PC. Actually it does connect in a way, but it receives and sents just a few packages. I can actually see in My Network Places how many packages does the Gateway make and it's a big difference. And it won't open any page. How should I set up the router so I can give enough bandwith to the Windows XP PC ? I've seen another problem that I forgot to mention. The router can't connect with the pppoe settings. I don't know why, but with Auto DHCP setting and my Windows 7 connected with pppoe settings works. EDIT2: I've installed Win 7 on the other PC so I won't have any problem of compatibility betwen them. But I still can't connect the router with PPPOE settings to the internet. It looks like this: http://img641.imageshack.us/img641/9780/capturefba.png If you need any other screens or info, please tell me.

  Read the article

• Linux VLAN Bridge

  - by raspi

  I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

  Read the article

• Can I use a Windows Server 2003 Domain Controller but my home router for DNS?

  - by NetworkingWannabie

  Hi All Probably easiest to start with a description of my current setup, which works (oh, and this is a home setup not an office or anything): I have an ADSL modem with a static IP address (192.168.128.1), and its DHCP capability is disabled. I have a permanently powered up Windows Server 2003 machine with a fixed IP (192.168.128.2) which provides my domain controller, dhcp, and dns. The default gateway for everything is my ADSL modem everything is setup to use the WS2003 machine as the primary DNS with the ADSL modem as Secondary DNS just in case the server goes down (everything includes the server itself). Lastly, just in case it's relevant, I have my DHCP leases set to infinite (or whatever the right term is). Everything is pretty hunky dory. Except, that is, for the fact that my server is ALWAYS on, and it isn't always used, so I'm burning juice that I don't need to - my server burns around 120W which isn't immense but isn't irrelevant either, so I'd like to put it into a stand-by state when it isn't being used (the more standby the better) and then get the clients to wake it up. Am I correct in assuming that this won't work at the moment - A given client would need an IP address to wake the machine up, and it needs to machine to be awake to get an IP - catch 22? Assuming I'm correct, can I move to using my router (which is always on) for DHCP? What impact will this have on DC and DNS? Alternatively, does anyone have a better way for me to achieve this? Can I get the server to wake up when it sees clients look for a DHCP server, etc? Wow, that came out longer than expected! Thanks for your help.

  Read the article

• Problems configuring logstash for email output

  - by user2099762

  I'm trying to configure logstash to send email alerts and log output in elasticsearch / kibana. I have the logs successfully syncing via rsyslog, but I get the following error when I run /opt/logstash-1.4.1/bin/logstash agent -f /opt/logstash-1.4.1/logstash.conf --configtest Error: Expected one of #, {, ,, ] at line 23, column 12 (byte 387) after filter { if [program] == "nginx-access" { grok { match = [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} [%{HTTPDATE:time_local}] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded = false host = " Here is my logstash config file input { syslog { type => syslog port => 5544 } } filter { if [program] == "nginx-access" { grok { match => [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} \[% {HTTPDATE:time_local}\] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded => false host => "localhost" cluster => "cluster01" } email { from => "[email protected]" match => [ "Error 504 Gateway Timeout", "status,504", "Error 404 Not Found", "status,404" ] subject => "%{matchName}" to => "[email protected]" via => "smtp" body => "Here is the event line that occured: %{@message}" htmlbody => "<h2>%{matchName}</h2><br/><br/><h3>Full Event</h3><br/><br/><div align='center'>%{@message}</div>" } } I've checked line 23 which is referenced in the error and it looks fine....I've tried taking out the filter, and everything works...without changing that line. Please help

  Read the article

• WiFi & GbE Slow while Both Active.

  - by Mark Tomlin

  I'm having a problem with my WiFi network connection when I use my wired GbE connection concurrently on my Laptop. I'm using my WiFi for Internet access, and general web surfing and I'm using my GbE connection to connect to my PlayStation so I can stream media. The WiFi connection is via a Linksys 610N connected to my Cable Modem. Where as the GbE connection is a direct connection from my Ethernet port to the Ethernet port of the PS3 via a Cat-5 cable (no router in between this connection). As soon as I connect the cable from the PS3 to my Ethernet port on my Laptop the WiFi connection slows to a halt, but then allows for a connection to the web as normal but at much slower speeds for the things like BitTorrent that stops completely. It seems to me that Windows can't handle both connections at once. It will have both active but it can only accept and send packets on one device at one time. I can get WiFi connections to work to go to websites and the like, but once I use my GbE connection to share media between my Laptop and my PS3 the Wifi connection dies out and I no longer have access to the internet. I setup my connection on the PS3 and the Laptop following the insturctions posted here: http://forums.finalgear.com/problems/s14e01-ps3-size-problem-40642/#post1188132 And the following is the results of my ipconfig. Windows IP Configuration Host Name . . . . . . . . . . . . : dygear Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter WiFi: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Network Connection Physical Address. . . . . . . . . : 00-19-**-**-**-** Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.111 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 167.206.254.2 167.206.254.1 Lease Obtained. . . . . . . . . . : Wednesday, May 19, 2010 08:55:30 Lease Expires . . . . . . . . . . : Thursday, May 20, 2010 08:55:30 Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-16-**-**-**-** Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.1.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Any ideas?

  Read the article

< Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >