Search Results

Search found 7856 results on 315 pages for 'bluechip solutions'.

Page 173/315 | < Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >

  • wireless blocked after installing ubuntu 12.04

    - by Cornelia Frank
    I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

    Read the article

  • The right way to add images to Monogame/Windows

    - by ashes999
    I'm starting out with MonoGame. For now, I'm only targeting Windows (desktop -- not Windows 8 specifically). I've used a couple of XNA products in the past (raw XNA, FlatRedBall, SilverSprite), so I may have a misunderstanding about how I should add images to my content. How do I add images to my project? Currently, I created a new Monogame project, added a folder called "Content," and added images under there; the only caveat is that I need to set the Copy to Output Directory action to one of the Copy ones. It seems strange, because my "raw" XNA project just last week had a Content project in it (XNA Framework Content Pipeline, according to VS2010), which compiled my images to XNB (I think). It seems like Monogame doesn't use the same content pipeline, but I'm not sure. Edit: My question is not about "how do I get the XNA content pipeline to work with Monogame." My question is "why would I want to use the XNA content pipeline in Monogame?" Because there are (at least) two solutions (that I see today): Add the images to the Monogame project and set the Copy to Output Directory options to copy. Add a XNA content pipeline project and add my images to that instead; reference it from my MOnogame project. Which solution should I use, and why? I currently have a working version with the first option.

    Read the article

  • Some hint to program a webservice "by subscription"

    - by Eagle
    I have some web sites programmed, I know to do it with python and PHP basically. Normally they are simple web sites, but now I want to provide REST web services but only for allowed users (allowed by me). I saw that a lot of services uses the "KEY" and "SECRET_KEY" concepts, which seems to be what I need (if I understand it right). My suppositions are: If I only do a GET service to retrieve, e.g., all my clients, without anymore, anyone can retrieve my clients without limitations. I will need some KEY generator to provide keys for my allowed users, so they can use my webservices. Only with a KEY is not enough: someone can steal a KEY and supplant my user (and this is the reason because exists a SECRET_KEY, right?). If all this is right, how can I make/use a system like that in my web services? Some open source example? Or maybe there are another easy solutions I'm not considering? My objective is to allow some users to use my web services.

    Read the article

  • How do I rescue files from the encrypted home folder via live USB stick?

    - by Alexia
    I know, this has been asked and answered all over the internet already. However, I start feeling stupid, since the informations there are not helping me. Just this morning, I wanted to install the newest update to 13.10. After the download, when it came to the actual installing, the install program froze and didn't do anything for hours. At that time, I was still logged in. The computer was working and everything was accessable to me. However, I made the mistake and didn't immediately make safety copies of everything. Instead, I just rebooted. Long story short: My computer even fails to reset to a previous version via Grub. But I am able to boot from a USB stick and, after starting Nautilus, I see my home folder on the HD. I would now like to copy its contents onto an external harddisk. Problem 1: I have no rights to access the folder like that. Problem 2: It is encrypted. Problem 3: I don't know how to give myself the rights to access the folder nor do I know how to encrypt it. I assume that it might help that I still know these things: - my old login name - my old login phrase - a 32 characters long string of hexadecimal numbers that I copied to my list of passwords as "Ubuntu Encryption Code". I copied it digitally right after installing Ubuntu the first time and encrypting the home folder, so there won't be any typos. I am sure of that. The solutions that I saw so far, tell me that I need the "encryption phrase". But when I follow the instructions and use this phrase that I have in my list, I only get messages of denial. Can anyone help me through this special problem, please?

    Read the article

  • Live Webcast: Make Better, Faster Decisions using Visualization - December 18th

    - by Melissa Centurio Lopes
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Register today for Oracle’s Primavera upcoming Live Webcast: Make Better, Faster Decisions using Visualization, December 18th at 12pm ET. Join this webcast and discover how Oracle’s AutoVue enhances Primavera solutions with visualization of project documents, enabling users to view and digitally collaborate, improving decision making and project execution. Don’t miss this live webcast: register today and learn how you can increase visibility, improve productivity and leverage existing infrastructures with Primavera and AutoVue.

    Read the article

  • Strategy for hosting 700+ domains names, each with a static HTML site

    - by jonschlinkert
    I have a portfolio of more than 700 domain names, and ideally I'd like to put up a single-page HTML/CSS/JavaScript webpage for each domain. Is there a system/strategy/workflow that will allow me to: Automate the deployment of new websites, quickly and easily without having to manually initiate each new website in an admin panel. For instance, I've seen dropbox-based solutions that claim to make it simple to setup new websites on your dropbox account, but you still have to set each one up in an admin interface first. It would be so much easier to have a folder naming convention that allowed the user to easily clone/copy/duplicate sites inside their Dropbox App folder (https://www.dropbox.com/developers/blog/23) to create new ones. Sounds interesting, however... It's easy to manage CNAMEs on the registrar-side, but is there a way to quickly associate CNAMEs with new websites (on the hosting side), maybe using the method offered by gh-pages-style (https://help.github.com/articles/setting-up-a-custom-domain-with-pages)? With GitHub's gh-pages, all you have to do is drop a file called CNAME into your repo, with the domain name you want associated with the repo inside the file. gh-pages isn't a good solution for what I'm doing though unfortunately. I'm also a front-end developer, specializing in rapid web development and "front-end build systems", so I building and maintaining static assets for hundreds of sites is no problem. It's the hosting-side that I really struggle with. Any suggestions?

    Read the article

  • Issue with image lightbox and enlargement / Jquery Mobile

    - by Matt
    I'm working on a redesign of my weather website using Jquery Mobile. I have it set up so that you drill down through a series of content containers to get to the weather info (each group of info opens in a dialog display). Everything's worked well, but I've run into an issue with my images. I have them sized so that they fit a mobile device's screen nicely, but because of that, when you look at them in a desktop browser, you can't really make out what the image is. I've tried several image lightbox / enlargement solutions, but for some reason, none of them have worked. Either nothing happens or the images open in a new window. I thought that this might be caused by Jquery Mobile somehow overwriting the scripts and css of the lightbox / enlargements I've tried. I'm not completely sure though that this is the case, and if it is, how I can get around it to be able to enlarge the images to their original size, preferably onclick. Here is a working (for the most part - still some kinks to work out) example. If you look under the "Tropical" section at the "Satellite-Derived Products", you'll see what I mean. http://www.suncoaststormwatch.com/Beta/Index.html

    Read the article

  • Oracle OpenWorld 2012 Hands-on Lab: “Leading Your Everyday Application Integration Projects with Enterprise SOA”

    - by Lionel Dubreuil
    Sharpen your Oracle skill sets and master Oracle technology in Oracle OpenWorld Hands-on Labs.In self-paced, practical learning sessions covering everything from business applications to middleware, database, storage, and enterprise management solutions, you'll discover new ways to derive maximum benefits from your Oracle hardware and software solutionsOracle experts will be available in person to answer questions and guide you through each lab.Hands-on Labs fill up early, and seats are limited, so don’t be late.This  HOL10093 - Leading Your Everyday Application Integration Projects with Enterprise SOA is scheduled for: Date: Monday, Oct 1 Time: 10:45 AM - 11:45 AM Location: Marriott Marquis - Salon 5/6 In this Hands-on Lab, Experience firsthand how Oracle Enterprise Repository, Oracle Application Integration Architecture (AIA) Foundation Pack, and Oracle SOA Suite work together to help you drive your enterprisewide integration projects.From asset management, discovery, and management in Oracle Enterprise Repository to integration of content in Oracle AIA Foundation Pack operating on the Oracle SOA Suite platform, discover how you can develop integrations to support business agility.Take advantage of Oracle-delivered integration assets and validate your services for compliance, within Oracle JDeveloper. You will get your hands on the tools and talk with Oracle experts in this hands-on lab.Objectives for this session are to: Use Oracle Enterprise Repository to manage application interfaces, composite applications, and business processes See how Oracle Enterprise Repository can benefit every service-based application integration project Learn how to govern services through the software lifecycle and validate your services for compliance

    Read the article

  • Oracle OpenWorld 2012 Hands-on Lab: “Leading Your Everyday Application Integration Projects with Enterprise SOA”

    - by Lionel Dubreuil
    Sharpen your Oracle skill sets and master Oracle technology in Oracle OpenWorld Hands-on Labs.In self-paced, practical learning sessions covering everything from business applications to middleware, database, storage, and enterprise management solutions, you'll discover new ways to derive maximum benefits from your Oracle hardware and software solutionsOracle experts will be available in person to answer questions and guide you through each lab.Hands-on Labs fill up early, and seats are limited, so don’t be late.This  HOL10093 - Leading Your Everyday Application Integration Projects with Enterprise SOA is scheduled for: Date: Monday, Oct 1 Time: 10:45 AM - 11:45 AM Location: Marriott Marquis - Salon 5/6 In this Hands-on Lab, Experience firsthand how Oracle Enterprise Repository, Oracle Application Integration Architecture (AIA) Foundation Pack, and Oracle SOA Suite work together to help you drive your enterprisewide integration projects.From asset management, discovery, and management in Oracle Enterprise Repository to integration of content in Oracle AIA Foundation Pack operating on the Oracle SOA Suite platform, discover how you can develop integrations to support business agility.Take advantage of Oracle-delivered integration assets and validate your services for compliance, within Oracle JDeveloper. You will get your hands on the tools and talk with Oracle experts in this hands-on lab.Objectives for this session are to: Use Oracle Enterprise Repository to manage application interfaces, composite applications, and business processes See how Oracle Enterprise Repository can benefit every service-based application integration project Learn how to govern services through the software lifecycle and validate your services for compliance

    Read the article

  • Network print to brother MFC-7420

    - by trampster
    I am trying to pint to a Brother MFC-7420 from my ubuntu 10.04 machine. The brother is attached to a windows XP machine and is shared. This is what I have tried: System-Administration-Printing, Add, Expand Network Printer, Windows Printer via SAMBA, Browse (I can find the printer no problems here), Foward, Choose Driver Dialog, Brother, My printer is not in this list So the next thing I tried was to download the printer driver from here http://welcome.solutions.brother.com/bsc/public_s/id/linux/en/download_prn.html The driver installed fine but my printer still does not appear in the list. I also tried installing the cups wrapper but that gave the following error. Restarting Common Unix Printing System: cupsd [ OK ] cp: cannot stat `/usr/share/cups/model/MFC7420.ppd': No such file or directory dpkg: error processing cupswrappermfc7420 (--install): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: cupswrappermfc7420 I tried connecting the printer directly but even though I have installed the driver, when I go to printers and click on the printer (it shows up fine as a USB printer) then it say searching for drivers and then gives me a list, this is the same list as before which doesn't have my printer. It really shouldn't be this hard. on window you don't have to installing anything it just works and the same is true for my brothers Mac. How do I print to my printer?

    Read the article

  • The Boston Globe Delivers Higher Satisfaction and Efficiency with Omni-Channel Support

    - by Tony Berk
    Unify customer interactions. Improve customer satisfaction. Increase agent efficiency. Better informed business decisions. These sound like a good set of goals for any business. Actually implementing processes to affect all of these is not necessarily easy for every business. On top of the normal challenges, throw in a rapidly changing industry and the challenge sounds daunting. But that's exactly what The Boston Globe took on, and customers are benefiting from a much improved experience. “We feel like we hit the bull’s eye with finding the right solution to support the growing digital environment,” said Robert Saurer, The Boston Globe's director of customer care and marketing.Oracle's RightNow CX solutions helped The Boston Globe to manage approximately 60,000 calls each month and respond to 5,000 monthly e-mails. More importantly, Web self-service rates are exploding and the online subscriber's most preferred support channel is chat. And what about social? The Boston Globe customer support team offers the same great level of support on their Facebook page and is monitoring Twitter and YouTube too! Read the full Customer Experience success story on The Boston Globe here.

    Read the article

  • Daten-Fluthelfer

    - by A&C Redaktion
    „Schneller entscheiden als der Wettbewerb", so heißt der neue Sales Guide zum Thema Business Intelligence für Oracle Partner. Unter diesem Motto gibt die Broschüre auf nur zwölf Seiten einen soliden Überblick, wie man die ungeheuren Datenmengen, mit denen Unternehmen tagtäglich zu kämpfen haben, effizient analysieren und nutzen kann. Alles fängt bekanntlich ganz harmlos an: Langsam und fast unbemerkt steigen die Datenmengen, bis sie plötzlich zum schier unlösbaren Problem werden - und das auf mehreren Ebenen: Die Endanwender sind unzufrieden über lange Ladeprozesse, die Datenqualität und die Abfrageperformance Die Betriebskosten steigen mit dem erhöhten Administrations- und Wartungsaufwand Die Entwicklungsproduktivität ist gering, denn der manuelle Aufwand für Datenbereinigung und -strukturierung ist hoch und die Anbindung neuer Datenquellen zunehmend kompliziert Irgendwann ist es an der Zeit für eine Gesamt-Architektur, die die Zentralisierung von BI- und Warehouse-Komponenten ermöglicht. Der Sales Guide zeigt Lösungen auf, für die sich verschiedene große Unternehmen entschieden haben, darunter ein internationaler Finanzdienstleister und eine der größten Online-Auktionsplattformen. Der Sales Guide behandelt nicht nur die Probleme rund um das Datawarehousing, sondern bietet wie immer auch eine Handreichung zur Ermittlung des Kundebedarfs und zum vertrieblichen Vorgehen. Hier geht's zum Download (nur mit OPN-Passwort): Sales Guide BI und Datawarehouse Mit dem Dauerthema Business Intelligence setzen sich auch die Oracle Solutions Partner Communities auseinander.

    Read the article

  • How to Effectively Create Bullet Patterns

    - by SoulBeaver
    I'm currently creating a top-down shooter like Touhou. The most important factor of the game is that there are many diverse patterns and ways at which bullets are generated and shot at the player, see this video: http://www.youtube.com/watch?v=4Nb5Ohbt1Sg#start=0:60;end=9:53; At the moment, I'm using a class "Pattern" which has a series of steps on moving and shooting. However, I feel this method is quite laborous as I have to create a new Pattern for each attack and perhaps new Bullet classes that will implement a certain behavior. This question received a comment suggesting I should look into BulletML for easy creation and storage of bullets with a specific pattern. It looks decent, but it led me to wonder, what other solutions do you have that I should take into consideration? Update My current design is as follows: An example of an implemented pattern: My GigasPattern first executes a teleport which moves Alice to a certain point (X, Y) on the screen. After this is completed, the pattern starts using the Mover to move the sprite around (whereas teleporting has separate effects and animation). These are of no concern, really, as they are quite simple. The Shooter also creates various Attacks, which are classes again that the Shooter can use to create various patterns of bullets, much like the one in the question I posted. Once the Mover has reached it's destination, both it and the shooter stop and return to an inactive state. The pattern completes, is removed by the AI and a new one gets chosen.

    Read the article

  • AME : How to Diagnose Issues With the Default Approver List in Purchasing When Using Approvals Management

    - by Oracle_EBS
    Do you need help in understanding the concepts or how to setup the Approval Management Engine (AME) for requisition approvals? See the new diagnostic Note 1437183.1 'AME : How to Diagnose Issues With the Default Approver List in Purchasing When Using Approvals Management'. AME is designed to generate the approval list according to the conditions and rules you define in the setup. This troubleshooting guide will help you understand how AME builds the default approval list for Purchasing and help users find solutions for scenarios where the approval list fails to be generated. Follow along with the logical steps for troubleshooting.  The note first reviews how to generate the AME Setup report.   For example in the note we see a fragment of the setup report. Notice it has different sections for each one of the setup categories including attributes, conditions, rules, action types, approval groups etc.  How the default approval list is built in AME is then reviewed, followed by the logical steps for diagnosing issues.  The diagnostic steps include how to run the Test Workbench, as well as how to obtain valuable debug and exception information.  Then follow along using the steps to build a simple test case to sharpen your understanding.

    Read the article

  • Hosting files with support for file tagging / keywords

    - by Zev Chonoles
    I have a large (approx. 25GB) collection of files I would like to host online for people to view or download. I have a spare computer I can use as a dedicated server for these files. I'm looking for a method of, or piece of software for, hosting my files where I can assign tags or keywords to the files, and people viewing my files online can search the collection via the tags. By way of approximate solutions I've found so far, I see that there is software such as Collectorz.com or Readerware for creating databases of one's books / music / movies, and these databases can be searched by tags or keywords, and the databases can be made available and searchable online; this would suit my purposes except that my files are not necessarily books, music, or movies, and I want the files themselves accessible online, not a database describing my files. A commercially-available solution like the ones above would be acceptable, but I'd prefer to have the whole setup under my control (i.e. I'd like to either implement it by hand, or use commercial software that doesn't rely on using the company's servers, paying them a continued fee, etc.). The current extent of my internet experience is designing a few Google Sites, so I know there's a fair chance I won't understand the answers I receive, but I'm always happy to have a summer project :)

    Read the article

  • FREE three days of online SharePoint 2010 development training for UK software houses Feb 9th to 11th

    - by Eric Nelson
    I have been working to get a SharePoint development course delivered online in February and March – online means lots of opportunities to ask questions. The first dates are now in place. The training is being delivered as a benefit for companies signed up to Microsoft Platform Ready. It is intended for UK based companies who develop software products* Agenda: Day 1 (Live Meeting 3 hours) 1:30 - 4:30 •         Getting Started with SharePoint: Understand why and how to start developing for SharePoint 2010 •         SharePoint 2010 Developer Roadmap:  Explore the new capabilities and features •         UI Enhancements: How to take advantage of the many UI enhancements including the fluent UI ribbon and  extensible dialog system. Day 2 (Live Meeting 3 hours) 1:30 - 4:30 •         Visual Studio 2010 Tools for SharePoint 2010: Overview of the project and item templates and a walkthrough of the designers •         Sandboxed Solutions: The new deployment model can help mitigate the risk of deploying custom code   •         LINQ to SharePoint:  SharePoint now fully supports LINQ for querying lists Day 3 (Live Meeting 3 hours) 1:30 - 4:30 •         Client Object Model: The Client OM can be accessed via web services, via a client (JavaScript) API, and via REST •         Accessing External Data: Business Connectivity Services (BCS) enables integration with back end systems •         Workflow: A powerful mechanism to create functionality using Windows Workflow Foundation Register for FREE (and tell your colleagues – we have a pretty decent capacity) To take advantage of this you need to: Sign your company up to Microsoft Platform Ready and record your SharePoint interest against one of your companies products Read about Microsoft Platform Ready Navigate to the “Get Technical Benefits” tab for SharePoint and click on Register Today You will then ultimately get an email with details of the Live Meeting to join on the 9th. But you should also favourite the team blog for any last minute details * Such companies are often referred to as an Independent Software Vendors. My team is focused on companies that create products used by many other companies or individuals. That could be a packaged product you can buy "off the shelf" or a Web Site offering a service - the definition is actually pretty wide these days :-) What it does not include is a company building software which will only be used by its own people.

    Read the article

  • Plan for your OpenWorld experience

    - by jeffrey.waterman
    Here is a partial list of the events which will take place at Oracle OpenWorld 2012, please take time out of your conference activities to get to these important, and informative, events: Attend the Sessions: General Session: Public Sector Wednesday, 3 October 10:15 a.m. – 11:15 a.m. Westin San Francisco Market Street – Metropolitan III Oracle Exadata, Oracle Exalogic, Oracle Exalytics, and Big Data Solutions in the Public Sector Wednesday, 3 October 11:45 a.m. – 12:45 p.m. Westin San Francisco Market Street – City Room Best Practices in the Use of Middleware for Information Sharing Across Agencies Wednesday, 3 October 1:15 p.m. – 2:15 p.m. Westin San Francisco Market Street – City Room Upgrading PeopleSoft Applications in the Public Sector Wednesday, 3 October 1:15 p.m. – 2:15 p.m. Westin San Francisco Market Street – Franciscan I Shared Services in Public Sector Organizations Wednesday, 3 October 3:30 p.m. – 4:30 p.m. Westin San Francisco Market Street – City Room Achieving Agility Through Closed-Loop Oracle Policy Automation Wednesday, 3 October 5:00 p.m. – 6:00 p.m. Westin San Francisco Market Street – Franciscan I The Value of Oracle E-Business Suite in the Public Sector Wednesday, 3 October 5:00 p.m. – 6:00 p.m. Westin San Francisco Market Street – City Ballroom Public Sector Reception Monday, 1 October 6:30pm – 9:30 pm Jillian’s, 101 Fourth Street

    Read the article

  • JAVA - multirow array

    - by user51447
    Here is my situation: a company has x number of employees and x number of machines. When someone is sick, the program have to give the best possible solution of people on the machines. But the employees can't work on every machine. I need a code for making little groups of possible solutions. this is a static example private int[][] arrayCompetenties={{0,0,1,0,1},{1,0,1,0,1},{1,1,0,0,1},{1,1,1,1,1},{0,0,0,0,1}}; = row is for the people and columns are for machines m1 m2 m3 m4 m5 m6 m7 p1 1 1 p2 1 1 1 1 p3 1 1 1 p4 1 1 1 p5 1 1 1 1 p6 1 1 1 1 p7 1 1 1 1 1 1 my question = with what code do i connect all the people to machine in groups (all the posibilities) like: p1 - m1 , p2-m2 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m3 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m4 , p3 - m5 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m5 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m2 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 .... i need a loop buth how? =D thanks!

    Read the article

  • You are invited! Quarterly Partner Sales Update Roadshow

    - by Giuseppe Facchetti
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Starting July this year, Oracle’s A&C, Partner Enablement and Hardware Teams will be organizing quarterly face-to-face sales training events to keep you up to date with Hardware sales news, latest products and solutions announcements, competitive positioning, sales tools -- all of this with an Oracle-on-Oracle approach.  We are pleased to invite you to attend the first Oracle EMEA Hardware Quarterly Partner Sales Update Roadshow running in 10 different cities across EMEA. The 3 hour, free of charge sales session will run in the afternoon in various locations.  Learn to Articulate the Oracle Hardware Business value proposition to your customers. Explain Oracle Hardware positioning versus the competition. Understand Oracle Hardware as best platform to run the complete Oracle-on-Oracle stack from Application to Disk Find all the details and register here! /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

    Read the article

  • Integrated Reporting Is Getting Closer

    - by Evelyn Neumayr
    By John O’Rourke, Vice President, Product Marketing, Oracle Oracle recently sponsored a webcast on CFO.com titled:  The CFO Playbook on Integrated Reporting: Integrating Sustainability into Financial Disclosures which focused on why top companies in the U.S. and overseas are incorporating sustainability content into their annual reports and other financial disclosures.  The webcast speakers, James Margolis, partner with Environmental Resources Management (ERM), a global provider of environmental, health, safety, risk and sustainability consulting services (EHSS) and Mike Wallace, Director of the Global Reporting Initiative's Focal Point USA, discussed the benefits of integrating sustainability reporting with traditional financial reporting. They noted how investors, corporate directors, lenders and most recently, the Securities and Exchange Commission, use this information to better understand, benchmark and value companies. They also talked about the November 2012 release of an Integrated Reporting Framework by the International Integrated Reporting Council (IIRC).  Read the press release and link to the framework here.  The shift towards integrated financial and sustainability reporting is gaining momentum with a number of global stock exchanges endorsing this approach in 2012.  Visit these links to listen to the webcast and download the slides. You can also view a demonstration of Oracle's solution for integrated financial and sustainability reporting. If you’re interested in learning more about this and Oracle’s other sustainability reporting solutions, click here. If you have any questions or need additional information, please feel free to contact me at [email protected].

    Read the article

  • Partner Webcast - Oracle Data Integration Competency Center (DICC): A Niche Market for services

    - by Thanos Terentes Printzios
    Market success now depends on data integration speed. This is why we collected all best practices from the most advanced IT leaders, simply to prove that a Data Integration competency center should be the primary new IT team you should establish. This is a niche market with unlimited potential for partners becoming, the much needed, data integration services provider trusted by customers. We would like to elaborate with OPN Partners on the Business Value Assessment and Total Economic Impact of the Data Integration Platform for End Users, while justifying re-organizing your IT services teams. We are happy to share our research on: The Economical impact of data integration platform/competency center. Justifying strongest reasons and differentiators, using numeric analysis and best-practice in customer case studies from specific industries Utilizing diagnostics and health-check analysis in building a business case for your customers What exactly is so special in the technology of Oracle Data Integration Impact of growing data volume and amount of data sources Analysis of usual solutions that are being implemented so far, addressing key challenges and mistakes During this partner webcast we will balance business case centric content with extensive numerical ROI analysis. Join us to find out how to build a unified approach to moving/sharing/integrating data across the enterprise and why this is an important new services opportunity for partners. Agenda: Data Integration Competency Center Oracle Data Integration Solution Overview Services Niche Market For OPN Summary Q&A Delivery Format This FREE online LIVE eSeminar will be delivered over the Web. Registrations received less than 24hours prior to start time may not receive confirmation to attend. Presenter: Milomir Vojvodic, EMEA Senior Business Development Manager for Oracle Data Integration Product Group Date: Thursday, September 4th, 10pm CEST (8am UTC/11am EEST)Duration: 1 hour Register Today For any questions please contact us at [email protected]

    Read the article

  • Triple-display setup using AMD drivers

    - by Halik
    I am currently running a dual display setup with nVidia 8800GTS video card, on a Ubuntu 12.10 box. The current setup uses nVidia TwinView to render the image on a 1920x1200 display and 1600x1200 one. I'm planning to add a third, 1280x1024 display to the setup. The change will require me to upgrade my GFX card to one supporting triple displays. I'll probably go with Sapphire Radeon 7770 (FLEX edition, to avoid additional active DP-DVI adapters). Before I invest in new GFX I wanted to ask - how well the AMD drivers will support such a setup. It does not matter whether it's fglrx or the OSS ones. If I remember correctly, when running Fedora on a Radeon x800, I had 'void' areas above and below the working area on my second display. The desktop was rendered in 1920+1280 width and 1200 height (which left 176px of vertical space accessible for my cursor and windows but not displayed on the screen - I'd prefer to avoid that). It may have very well been my misconfiguration back then. Generally, are there any solutions from AMD on par with TwinView? Or is it a non-issue at all? Also, I'm wondering about the usual stuff - hardware h264 decoding support, glitch-free flash support, any issues with Compiz/Unity?

    Read the article

  • How can I configure the embedded wireless card in a Toshiba Satellite Pro 4600 to work under Lubuntu 10.10?

    - by MoLE
    I'm struggling to get the embedded wireless card in this laptop to work. In 7.10 (gutsy) it worked fine. Now I'm trying to get 10.10 (maverick) working on it, and am using the Lubuntu flavour due to the low resources of this laptop. The hardware: Appears to be an embedded pcmcia card. pccardctl ident gives: Socket 0: product info: "TOSHIBA", "Wireless LAN Card", "Version 01.01", "" manfid: 0x0156, 0x0002 function: 6 (network) The default kernel recognises the card and loads the orinoco_cs driver. orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0001:0006:000e orinoco_cs 0.0: Firmware determined as Lucent/Agere 6.14 Then for some reason, the driver isn't happy with this and gives: orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0002:0009:0030 orinoco_cs 0.0: Firmware determined as Lucent/Agere 9.48 All seems ok until I try to associate with my access point using Network Manager. eth1: Lucent/Agere firmware doesn't support manual roaming repeated about 10 times then NM gives up. According to the linuxwireless.org wiki page on this driver, this is a known issue, and I quote: Known issues Roaming and WPA_supplicant Lucent/Agere firmware doesn't support manual roaming On the Agere cards, roaming is controlled by the firmware instead of userspace. You will get the above message if userspace attempts to associate with a specific AP rather than by SSID. If you are using wpa_supplicant use ap_scan=2 mode. NetworkManager uses wpa_supplicant, so the above also applies. At this point my google-fu has failed me, and I can't find how to configure network manager to use the mystical "ap_scan=2" mode via wpa_supplicant. I have tried the following suggested solutions (from launchpad or the forums) deleting the agere* files from /lib/firmware using wicd instead of network manager combining both blacklisting the orinoco_cs driver in an attempt to force use of the hostap_cs driver instead (in case it is a prism2 card). Obviously none of them have worked for me. Any hints on how to perform the suggested workaround above? Edit: I have also confirmed working on 8.10 (intrepid) live CD.

    Read the article

  • Endeca Information Discovery 3-Day Hands-on Training Boot-Camp

    - by Mike.Hallett(at)Oracle-BI&EPM
    For Oracle Partners, on October 15-17, 2012 in Paris, France: Register here. The Oracle Endeca Information Discovery (OEID) Boot-Camp is designed to give partners an understanding of OEID’s features, and how it complements the existing Oracle Business Intelligence suite. Participants will learn how to develop & implement solutions using a Data Discovery method.  Training is in English. What will be covered? The Oracle Endeca Information Discovery (OEID) Boot Camp is a three-day class with a combination of lecture and hands-on exercises, tailored to make participants aware of the Oracle Endeca Information Discovery platform, and to gain valuable skills for the implementation of projects.   Prerequisites You must bring a laptop with you for the Hands-on labs: Attendees should have experience and familiarity with the basic concepts of business intelligence and be OPN Partners with Gold or above membership.  This training is free to OPN Partners. Click here for more information. Where and When ? Monday, October 15th until Wednesday, October 17th included  9:00 - 18:00 Oracle France 15, boulevard Charles de Gaulle 92715 Colombes: Access Venue Map Register here  : NOTE there is a Limited number of seats, you will get confirmation within 2 weeks.

    Read the article

  • Good design for class with similar constructors

    - by RustyTheBoyRobot
    I was reading this question and thought that good points were made, but most of the solutions involved renaming one of the methods. I am refactoring some poorly written code and I've run into this situation: public class Entity { public Entity(String uniqueIdentifier, boolean isSerialNumber) { if (isSerialNumber) { this.serialNumber = uniqueIdentifier; //Lookup other data } else { this.primaryKey = uniqueIdentifier; // Lookup other data with different query } } } The obvious design flaw is that someone needed two different ways to create the object, but couldn't overload the constructor since both identifiers were of the same type (String). Thus they added a flag to differentiate. So, my question is this: when this situation arises, what are good designs for differentiating between these two ways of instantiating an object? My First Thoughts You could create two different static methods to create your object. The method names could be different. This is weak because static methods don't get inherited. You could create different objects to force the types to be different (i.e., make a PrimaryKey class and a SerialNumber class). I like this because it seems to be a better design, but it also is a pain to refactor if serialNumber is a String everywhere else.

    Read the article

< Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >