Search Results

Search found 5367 results on 215 pages for 'devices'.

Page 173/215 | < Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >

  • Can't mount FAT32 drive under Ubuntu Linux

    - by Josh
    I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

    Read the article

  • Improving IO with FlashCache

    - by Devator
    I have a server with 2 HDD's (2x 1 TB), running in RAID 1 (SW-RAID). I want to improve IO performance by using flashcache. There are running KVM virtual machines on it, using LVM. Regarding this, I have the following questions: Will this even work? flashcache works for block devices, however these are all virtual machines with their own setup. How much would I expect to increase performance? Most virtual machines run websites and some host games. How big does the SSD needs to be? Would having a bigger SSD increase performance since it's able to cache more files? What happens if the SSD dies? Would flashcache retrieve files from the traditional HDD and I could simply replace the SSD? How much faster would writeback be in comparison with writethrough and writearound? I have no access to a test system unfortunately, so could I install flashcache on a live server without unmounting the the disks? I found a great tutorial here which I would be using.

    Read the article

  • ATI HDMI Audio disappears in Windows 7 when a TV is connected

    - by jsalonen
    So far I have unsuccessfully googled for HOURS with no luck fixing this very annoying problem. The settings is the following: I have PC running Windows 7 RC (64-bit) Video card is a ATI Radeon 4850 series card (Sapphire HD 4850 512MB to be exact) The video card has HDMI out with built-in audio chip I have an HDMI cable connecting the PC to a TV (Sony Bravia series) The problem is that when I connect the HDMI cable to the TV, the ATI HDMI Sound output device disappears completely from the list of playback devices in Windows. As a workaround I can restore the audio by re-installing the HDMI audio driver. However, when I disconnect the TV the driver disappears again. So basically, every time I want to watch stuff on my TV, I have to reinstall audio driver, which of course is VERY annoying. EDIT: I have figured out that I do not need to re-istall the HDMI audio driver to restore sound; I only need to reboot my computer with the HDMI cable plugged in to restore the audio driver. This suggests that the problem has something to do with information passed from TV to computer, which makes my HDMI Audio driver disappear. Are there any other, more elegant workarounds for this problem? All help is much appreciated!

    Read the article

  • Trying to understand Wireless N vs Wireless AC

    - by EGHDK
    Whenever a new wireless standard gets approved you expect faster speeds and longer range. From everything that I've read about it, it seems that AC will only transfer over the 5GHz band and up to 3Gbps. Studying the new AC routers on the market, it seems that they will transfer over 5GHz and 2.4GHz. And 5GHz will only transfer at 1.3Gbps. Which isn't what AC is supposed to be. I know there is a difference between what the standard actually says, and what products will actually do, but is there any reason for this? Is there any other main differences between AC and N? I've heard people discussing AC and saying that it's finally "fixing" what N was supposed to fix... what do they mean by that? Any security benefits? I have seen this image online: Will AC really do that? Will that require an AC network card in my laptop for that to actually happen? Lastly, will the router only be able to communicate with AC devices if I have beamforming technology on? I know it's a ton of questions, but most articles online seem to be outdated, and don't provide too much reliability.

    Read the article

  • UAC being turned off once a day on Windows 7

    - by Mehper C. Palavuzlar
    I have strange problem on my HP laptop. This began to happen recently. Whenever I start my machine, Windows 7 Action Center displays the following warning: You need to restart your computer for UAC to be turned off. Actually, this does not happen if it happened once on a specific day. For example, when I start the machine in the morning, it shows up; but it never shows up in the subsequent restarts within that day. On the next day, the same thing happens again. I never disable UAC, but obviously some rootkit or virus causes this. As soon as I get this warning, I head for the UAC settings, and re-enable UAC to dismiss this warning. This is a bothersome situation as I can't fix it. First, I have run a full scan on the computer for any probable virus and malware/rootkit activity, but TrendMicro OfficeScan said that no viruses have been found. I went to an old Restore Point using Windows System Restore, but the problem was not solved. What I have tried so far (which couldn't find the rootkit): TrendMicro OfficeScan Antivirus AVAST Malwarebytes' Anti-malware Ad-Aware Vipre Antivirus GMER TDSSKiller (Kaspersky Labs) HiJackThis RegRuns UnHackMe SuperAntiSpyware Portable Tizer Rootkit Razor (*) Sophos Anti-Rootkit SpyHunter 4 There are no other strange activities on the machine. Everything works fine except this bizarre incident. What could be the name of this annoying rootkit? How can I detect and remove it? EDIT: Below is the log file generated by HijackThis: Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 13:07:04, on 17.01.2011 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16700) Boot mode: Normal Running processes: C:\Windows\system32\taskhost.exe C:\Windows\system32\Dwm.exe C:\Windows\Explorer.EXE C:\Program Files\CheckPoint\SecuRemote\bin\SR_GUI.Exe C:\Windows\System32\igfxtray.exe C:\Windows\System32\hkcmd.exe C:\Windows\system32\igfxsrvc.exe C:\Windows\System32\igfxpers.exe C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe C:\Program Files\Synaptics\SynTP\SynTPEnh.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QLBCTRL.exe C:\Program Files\Analog Devices\Core\smax4pnp.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\VolCtrl.exe C:\Program Files\LightningFAX\LFclient\lfsndmng.exe C:\Program Files\Common Files\Java\Java Update\jusched.exe C:\Program Files\Microsoft Office Communicator\communicator.exe C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe C:\Program Files\Trend Micro\OfficeScan Client\PccNTMon.exe C:\Program Files\Microsoft LifeCam\LifeExp.exe C:\Program Files\Hewlett-Packard\Shared\HpqToaster.exe C:\Program Files\Windows Sidebar\sidebar.exe C:\Program Files\mimio\mimio Studio\system\aps_tablet\atwtusb.exe C:\Program Files\Microsoft Office\Office12\OUTLOOK.EXE C:\Program Files\Babylon\Babylon-Pro\Babylon.exe C:\Program Files\Mozilla Firefox\firefox.exe C:\Users\userx\Desktop\HijackThis.exe R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page = about:blank R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://go.microsoft.com/fwlink/?LinkId=54896 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R0 - HKLM\Software\Microsoft\Internet Explorer\Search,SearchAssistant = R0 - HKLM\Software\Microsoft\Internet Explorer\Search,CustomizeSearch = R1 - HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings,AutoConfigURL = http://www.yaysat.com.tr/proxy/proxy.pac R0 - HKCU\Software\Microsoft\Internet Explorer\Toolbar,LinksFolderName = O2 - BHO: AcroIEHelperStub - {18DF081C-E8AD-4283-A596-FA578C2EBDC3} - C:\Program Files\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll O2 - BHO: Babylon IE plugin - {9CFACCB6-2F3F-4177-94EA-0D2B72D384C1} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [IgfxTray] C:\Windows\system32\igfxtray.exe O4 - HKLM\..\Run: [HotKeysCmds] C:\Windows\system32\hkcmd.exe O4 - HKLM\..\Run: [Persistence] C:\Windows\system32\igfxpers.exe O4 - HKLM\..\Run: [hpWirelessAssistant] C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe O4 - HKLM\..\Run: [SynTPEnh] C:\Program Files\Synaptics\SynTP\SynTPEnh.exe O4 - HKLM\..\Run: [QlbCtrl.exe] C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QlbCtrl.exe /Start O4 - HKLM\..\Run: [SoundMAXPnP] C:\Program Files\Analog Devices\Core\smax4pnp.exe O4 - HKLM\..\Run: [Adobe Reader Speed Launcher] "C:\Program Files\Adobe\Reader 9.0\Reader\Reader_sl.exe" O4 - HKLM\..\Run: [Adobe ARM] "C:\Program Files\Common Files\Adobe\ARM\1.0\AdobeARM.exe" O4 - HKLM\..\Run: [lfsndmng] C:\Program Files\LightningFAX\LFclient\LFSNDMNG.EXE O4 - HKLM\..\Run: [SunJavaUpdateSched] "C:\Program Files\Common Files\Java\Java Update\jusched.exe" O4 - HKLM\..\Run: [Communicator] "C:\Program Files\Microsoft Office Communicator\communicator.exe" /fromrunkey O4 - HKLM\..\Run: [AgentUiRunKey] "C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe" -ni -sss -e http://localhost:16386/ O4 - HKLM\..\Run: [OfficeScanNT Monitor] "C:\Program Files\Trend Micro\OfficeScan Client\pccntmon.exe" -HideWindow O4 - HKLM\..\Run: [Babylon Client] C:\Program Files\Babylon\Babylon-Pro\Babylon.exe -AutoStart O4 - HKLM\..\Run: [LifeCam] "C:\Program Files\Microsoft LifeCam\LifeExp.exe" O4 - HKCU\..\Run: [Sidebar] C:\Program Files\Windows Sidebar\sidebar.exe /autoRun O4 - Global Startup: mimio Studio.lnk = C:\Program Files\mimio\mimio Studio\mimiosys.exe O8 - Extra context menu item: Microsoft Excel'e &Ver - res://C:\PROGRA~1\MICROS~1\Office12\EXCEL.EXE/3000 O8 - Extra context menu item: Translate this web page with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/ActionTU.htm O8 - Extra context menu item: Translate with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/Action.htm O9 - Extra button: Research - {92780B25-18CC-41C8-B9BE-3C9C571A8263} - C:\PROGRA~1\MICROS~1\Office12\REFIEBAR.DLL O9 - Extra button: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O9 - Extra 'Tools' menuitem: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O16 - DPF: {00134F72-5284-44F7-95A8-52A619F70751} (ObjWinNTCheck Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/WinNTChk.cab O16 - DPF: {08D75BC1-D2B5-11D1-88FC-0080C859833B} (OfficeScan Corp Edition Web-Deployment SetupCtrl Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/setup.cab O17 - HKLM\System\CCS\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\Software\..\Telephony: DomainName = yaysat.com O17 - HKLM\System\CS1\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\System\CS2\Services\Tcpip\Parameters: Domain = yaysat.com O18 - Protocol: qcom - {B8DBD265-42C3-43E6-B439-E968C71984C6} - C:\Program Files\Common Files\Quest Shared\CodeXpert\qcom.dll O22 - SharedTaskScheduler: FencesShellExt - {1984DD45-52CF-49cd-AB77-18F378FEA264} - C:\Program Files\Stardock\Fences\FencesMenu.dll O23 - Service: Andrea ADI Filters Service (AEADIFilters) - Andrea Electronics Corporation - C:\Windows\system32\AEADISRV.EXE O23 - Service: AgentService - Iron Mountain Incorporated - C:\Program Files\Iron Mountain\Connected BackupPC\AgentService.exe O23 - Service: Agere Modem Call Progress Audio (AgereModemAudio) - LSI Corporation - C:\Program Files\LSI SoftModem\agrsmsvc.exe O23 - Service: BMFMySQL - Unknown owner - C:\Program Files\Quest Software\Benchmark Factory for Databases\Repository\MySQL\bin\mysqld-max-nt.exe O23 - Service: Com4QLBEx - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\Com4QLBEx.exe O23 - Service: hpqwmiex - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\Shared\hpqwmiex.exe O23 - Service: OfficeScanNT RealTime Scan (ntrtscan) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\ntrtscan.exe O23 - Service: SMS Task Sequence Agent (smstsmgr) - Unknown owner - C:\Windows\system32\CCM\TSManager.exe O23 - Service: Check Point VPN-1 Securemote service (SR_Service) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Service.exe O23 - Service: Check Point VPN-1 Securemote watchdog (SR_Watchdog) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Watchdog.exe O23 - Service: Trend Micro Unauthorized Change Prevention Service (TMBMServer) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\..\BM\TMBMSRV.exe O23 - Service: OfficeScan NT Listener (tmlisten) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\tmlisten.exe O23 - Service: OfficeScan NT Proxy Service (TmProxy) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\TmProxy.exe O23 - Service: VNC Server Version 4 (WinVNC4) - RealVNC Ltd. - C:\Program Files\RealVNC\VNC4\WinVNC4.exe -- End of file - 8204 bytes As suggested in this very similar question, I have run full scans (+boot time scans) with RegRun and UnHackMe, but they also did not find anything. I have carefully examined all entries in the Event Viewer, but there's nothing wrong. Now I know that there is a hidden trojan (rootkit) on my machine which seems to disguise itself quite successfully. Note that I don't have the chance to remove the HDD, or reinstall the OS as this is a work machine subjected to certain IT policies on a company domain. Despite all my attempts, the problem still remains. I strictly need a to-the-point method or a pukka rootkit remover to remove whatever it is. I don't want to monkey with the system settings, i.e. disabling auto runs one by one, messing the registry, etc. EDIT 2: I have found an article which is closely related to my trouble: Malware can turn off UAC in Windows 7; “By design” says Microsoft. Special thanks(!) to Microsoft. In the article, a VBScript code is given to disable UAC automatically: '// 1337H4x Written by _____________ '// (12 year old) Set WshShell = WScript.CreateObject("WScript.Shell") '// Toggle Start menu WshShell.SendKeys("^{ESC}") WScript.Sleep(500) '// Search for UAC applet WshShell.SendKeys("change uac") WScript.Sleep(2000) '// Open the applet (assuming second result) WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{ENTER}") WScript.Sleep(2000) '// Set UAC level to lowest (assuming out-of-box Default setting) WshShell.SendKeys("{TAB}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") '// Save our changes WshShell.SendKeys("{TAB}") WshShell.SendKeys("{ENTER}") '// TODO: Add code to handle installation of rebound '// process to continue exploitation, i.e. place something '// evil in Startup folder '// Reboot the system '// WshShell.Run "shutdown /r /f" Unfortunately, that doesn't tell me how I can get rid of this malicious code running on my system. EDIT 3: Last night, I left the laptop open because of a running SQL task. When I came in the morning, I saw that UAC was turned off. So, I suspect that the problem is not related to startup. It is happening once a day for sure no matter if the machine is rebooted.

    Read the article

  • Cisco Pix 515 ip addressing

    - by Rickard
    I have just gotten my hands on a Cisco Pix 515 (not 515E) with 3 interfaces, and are just about to start some labs. In my lab, I am using a real life scenario from an actual setup at work. As I have no access to the device at work, I am simply trying to replicate the scenario by trial and error. At work, we are given two IP addresses from the provider, which is 1-to-1 nated addresses. The addresses we are allowed to use are: 10.131.35.4-5/29 Now, we have 3 servers on a DMZ, 192.168.2.2-4/24 and 17 client computers on 192.168.1.100-117/24 aswell as some static addressed devices on 192.168.1.8-18/27 My question is, how would I best set up so that the machines on the DMZ get's translated to 10.131.35.4 and the machines on 192.168.1.* will be translated to 10.131.35.5 I don't expect or want anyone to give me a fully functional config, I may learn from it, but I'd prefer to just have some advices or maybe a guide on how to set it up. I hope someone can shed some light over my situation, have been looking through google but I guess I don't the searchwords I'm using isn't too good as I can't find any good clues. THank you very much! PS. Maybe I should add, I am not unfamiliar with the Cisco CLI, as I prefer using that before any gui's. So not really looking for any solutions for the ASDM. DS.

    Read the article

  • Selective Pointer device remapping in linux

    - by user6368
    I just got an HP 2710p (hp tablet, with digitizer), and I've played around with linux for a while now, and thought I would go ahead and install it. Everything works fine, excepting normal tablet functions, which is to be expected. I'm working on the screen rotation, and there are on-screen keyboards, etc, but I'm having issues with the stylus. I can tap and left click with the stylus as normal, but the side button (which in windows functions as a right mouse button) appears as a 'button 2' to xev (a middle/scroll wheel button). I can switch 'button 2' and 'button 3' universally using xmodmap, but I'd like to do so exclusively for stylus so I don't screw up regular pointing devices. Altering xorg.conf (which is surprisingly bare) with the recommended sections (adding sections for each of the stylus buttons) does nothing. I'm running crunchbang, which is an ubuntu/debian varient with openbox as the windows manager. Thanks Also, as a seperate note, does anybody know how to detect when I rotate and/or latch the lid shut? I was thinking maybe I could run a script to switch the buttons when I close it, but I can't find any information.

    Read the article

  • Running a VM off a USB 2.0 Flash Drive - Mac/Parallels/XP

    - by geerlingguy
    I use a MacBook Air as my primary machine, and the 128GB SSD means space is precious. To save about 10 GB, I've been running Parallels with a Windows XP VM off an external USB hard drive, which performs as well in everyday use as running the VM off the internal SSD. So, I bought a tiny 32GB USB 2.0 flash drive, plugged it into the MacBook Air, formatted it first as ExFAT (which was slow), then as Mac OS Extended (Journaled) (which was also slow), and copied over my VM file, and ran Parallels off it. My full experience is documented here: http://www.midwesternmac.com/blogs/jeff-geerling/running-windows-xp-vm Straight file copies are really fast — 30 MB/sec read (solid the whole time), and 10-11 MB/sec write (solid the whole time). But I noticed that once XP started running, the disk access rates were in the low KB ranges. Are USB flash drives really that poor at random access, or could I possibly be missing something (the format of the flash drive, etc.?)? Of note, I've tried the following, to no great effect: Formatting the drive as either ExFAT or Mac OS Extended (Journaled) Unplugging all other USB devices and turning off Bluetooth (which runs on the right-side-port USB bus). Plugging in the flash drive either direct in the right side port, or the left side port, or into a USB 2.0 hub

    Read the article

  • Wireless Activity Monitoring for PCI DSS Compliance

    - by dkusleika
    In an effort to be PCI DSS compliant, I took a trustkeeper.net questionnaire. I failed the question that asks Is the presence of wireless access points tested for by using a wireless analyzer at least quarterly or by deploying a wireless IDS/IPS to identify all wireless devices in use? (SAQ #11.1) My only wireless access point is outside my firewall, so even if you cracked my wireless you couldn't get inside my domain (unless you crack that too). My firewall doesn't have IPS and I couldn't tell if it had IDS. I looked around for a wireless analyzer, but what I found was $500, which is a little pricey for my size business. And even if I got it, I'm not sure I would understand what it tells me. Surely there are smaller/less sophisticated businesses that take credit cards and have solved this. My questions are: What are the risks if someone were to crack my wireless? (Could they read all internet traffic? Just wireless traffic? Just use my internet connection?) And what is the best/cheapest way to test my connection point quarterly? Should I buy the $500 analyzer? Domain is Windows Server 2000. Firewall is Sonicwall Pro 2040. Router is 8 port D-link.

    Read the article

  • Toshiba External Hard Drive freezes computer

    - by Ephraim
    I bought a Toshiba Canvio Basics E05A032BAU2XK Portable External 320GB 2.5 Hard Drive: My computer has two Os's on it Win7 and Win XP. I need both. The main one I use is XP. When booting my computer in any OS the computer and hard drive work fine. The same holds true for plugging in the hard drive while running Win7. However, when running WinXP, if the hard drive gets plugged in the computer freezes(my main point is that the HD is portable so it is essential that it does not do this, as I said I usually run XP). After reading some online forums I was informed that there is a compatibility issue with the newest version of Eset Smart Security(I still don't understand this because it works fine in Win7 or when connected on boot...). I disabled the AV and plugged in the HD... Walla! The comnputer did not freeze. However the disk is not recognized in explorer or disk management. In device manager I removed the device and did a scan and installation of device failed. It pretty much sounds like a driver issue but I cannot find any drivers for this HD. In fact, Toshiba claims that there are no downloadable drivers for it and that XP should take care of the drivers itself. What to do? As far as I can tell, all other USB devices work just fine on both OS. Please Help!

    Read the article

  • Can I setup NAT for the same service, two public IPs on different routers to the same private IP?

    - by James
    This might be needlessly complex, but here goes. I've got two Firebox x550e devices. The first has a local IP of 10.0.0.1, public IP 64.x.x.x. The second has a local IP of 10.0.0.10, public IP 70.x.x.x. There is an FTP server on our LAN with a private IP of 10.0.0.55. I've set up NAT rules in each of the Fireboxes, on the first firebox it is 64.x.x.x-10.0.0.55 tcp 21, on the second 70.x.x.x-10.0.0.55 tcp 21. The first rule works fine. I can ftp to 64.x.x.x and everything's good. The second rule doesn't work. ftp to 70.x.x.x results in a connection timeout. The second firebox logs say the connection is being allowed through. The default gateway on the FTP server is 10.0.0.1 (the first firebox) If I change the default gateway on the server to 10.0.0.10, the rule on the second firebox starts working, but the rule from the first firebox stops. Is there some way to make this work for both rules?

    Read the article

  • network policy + WPA enterprise (tkip) Windows 2008 R2

    - by Aceth
    hi I've attempted the following guide and in a bit of a pickle. http://techblog.mirabito.net.au/?p=87 My main goal is to have a username / password based wireless authentication with active directory integration. I keep getting the error Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\rhysbeta Account Name: rhysbeta Account Domain: domain Fully Qualified Account Name: domain\rhysbeta Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 00-12-BF-00-71-3C:wirelessname Calling Station Identifier: 00-23-76-5D-1E-31 NAS: NAS IPv4 Address: 0.0.0.0 NAS IPv6 Address: - NAS Identifier: - NAS Port-Type: Wireless - IEEE 802.11 NAS Port: 2 RADIUS Client: Client Friendly Name: Belkin54g Client IP Address: x.x.x.10 Authentication Details: Connection Request Policy Name: Secure Wireless Connections Network Policy Name: Secure Wireless Connections Authentication Provider: Windows Authentication Server: srvr.example.com Authentication Type: EAP EAP Type: - Account Session Identifier: - Logging Results: Accounting information was written to the local log file. Reason Code: 22 Reason: The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server. ` I would love to have it so that non domain devices

    Read the article

  • Microsoft Arc Mouse OS X

    - by meepz
    I recently bought a new Mac Book Pro with Mountain Lion 10.8 on it. The only portable mouse I have is my Microsoft Arc Mouse. I wanted to use it with the laptop so I installed the IntelliPoint 8.2 for Mac from Microsofts website. According to their website, this driver is for OS X 10.4-10.7. Now I thought that wouldnt be too much of an issue but unfortunately for me, the driver installs fine and the mouse is detected but I get no movement and when I click the buttons nothing happens. I took the mouse with me on a business trip to EU and before I left I checked if the mouse worked with my desktop which is running Windows 7 and it worked without any hiccups. I'm not too sure where the OS differs from 10.7 to 10.8. I found an article online but it doesn't pertain to my mouse, although it could be of assistance. I have tried my version of their adjustment but I am not too knowledgable on low level hardware/software modifications so I may have done it wrong. heres the link: http://refluxions.wordpress.com/2008/08/18/mac-os-x-mouse-madnessfixed/ I get the following details when I check mouse info in the IntelliPoint preferences pane: The following Microsoft mouse devices are currently connected to your Macintosh driven by the Intellipoint software. Arc Mouse Vendor name: Microsoft Product name: Microsoft AE 2.4GHz Transceiver 5.0 Vendor ID: 045E Product ID: 074F Device version: 0140 if anyone has any suggestions on how to fix this it would be greatly appreciated! I love the mouse and im here in EU for another two weeks. Thanks

    Read the article

  • How to backup iTunes on Windows to folder/share, i.e. without "Back Up to Disc"? No DVD writer avail

    - by Chris W. Rea
    (Surprised I didn't already find an answer here to this!) I've got a computer on which I'd like to back up the iTunes library – music, movies, apps, everything. We're talking multiple gigabytes. Unfortunately, it seems that iTunes' own built-in "Back Up to Disc" feature (the only backup feature I can find in iTunes) only functions with a CD or DVD writer/burner. The computer in question does not have a DVD burner. While it has a CD burner, attempting to back up to CDs would require dozens of discs plus more time than I'm willing to spend swapping them. So: What is the recommended way to back up an entire iTunes library on a Windows computer, to a non-CD/DVD location such as an external hard drive or a network shared folder? Then, once such a backup has been performed, what is the process for restoring the library – e.g. after the computer has been repaved with a new version of Windows – so that iTunes is resurrected whole and recognizes devices it syncs with? Thank you!

    Read the article

  • Sharing files between 2 different routers

    - by Chris
    I realize this has been asked before and I have read as much as I could find on the topic but I still need help with this because there are so many different approaches and the ones I am trying aren't working. So I have 2 routers, lets call them A and B. Both have a wireless feature and are active. A is in the basement and receives the internet. There is a TV on the ground floor that is connected to A through an ethernet wire. B is upstairs and gets the internet from A through an ethernet wire. Connected to B, is a desktop running Plex Media Server. What I want to do is make sure devices connected to both routes can access the Plex Media Server. So what I have read is that I should plug in the ethernet wire connecting B to a into a LAN port instead of the WAN port. After that I should turn off DHCP. I have tried this and B stops receiving internet. What am I doing wrong? Another thing I have read is to use Router B in bridge mode but Router B is running openwrt and I have QoS on it so gaming/VoIP/browsing is unaffected by heavy downloading/uploading. I would prefer to keep this active. I realize it might be ineffective if a device in Router A is doing some hardcore downloading but all that stuff is done on Router B anyway so it doesn't matter. Router A can't get openwrt because it is a shitty one provided by Bell. So, how do I proceed with this?

    Read the article

  • No LPT port in Windows 7 virtual machines

    - by KeyboardMonkey
    Windows 7 has MS virtual PC integrated, the VM settings don't give a parallel LPT port mapping to the physical machine. Where did it go? Has anyone else noticed this, and found a solution? Update: After much digging, I found the one and only reference to this issue, on the VPC Blog: "Parallel port devices are not supported, as they are relatively rare today." -More details- It's a XP VM I've been using since VPC 2007 days, which did have this functionality. This is to configure barcode printers via the LPT port. Since the (new) MS VM can't map to my physical LPT port, I'm having a hard time configuring printers. My physical ports are enabled in the BIOS. It has worked the past 3 years, before switching to Win 7. Any help is appreciated. This screen shot of the VM settings shows COM ports, but LPT is no more In contrast, here is a screen shot of VPC 2007 (before it got integrated into Win 7). Notice how it has LPT support

    Read the article

  • CentOS - mdadm raid1 drive won't mount to default location

    - by danny
    I'm running CentOS 5.5, the system, boot, swap, etc. is all on /dev/sda and I have two identical single-partition drives /dev/sdb1 /dev/sdc1 that are configured in RAID1 (using mdadm). It was working fine (configured to mount to /mnt/data in the fstab file) and I recently let yum install a couple of automatic updates without paying attention to what they were, and now it doesn't work. Raid is working fine (dmesg shows it gets loaded correctly). mdstat shows: # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdc1[1] sdb1[0] XXXX blocks [2/2] [UU] unused devices: <none> Additionally, I can mount it anywhere other than its default directory (i.e. the following works, and I can read data off the drives). # mount /dev/md0 /mnt/data2 EXT3-fs warning: mounting fs with errors, running e2fsck is recommended But when I run the following I get: # mount -a mount: /dev/sdb1 already mounted or /mnt/data busy It says nothing is mounted when I try to umount /dev/sdb1 or umount /mnt/data, so I assume it's the second of those errors. However, lsof | grep mnt shows nothing. The weird thing is that I can save files in /mnt/data. So something is obviously mounted there, but when I try to umount it I get the error that nothing is mounted. /etc/mtab doesn't mention any of the partitions or files I am trying to work with, and fstab just has that one line I mentioned above that is supposed to mount my raid partition. Again, it was all working fine until I On Google I've found a few things about dmraid interfering with mdadm after an update, but I yum remove'd dmraid and rebooted and it didn't help. I'm really confused and need to get this working to get on with my work!

    Read the article

  • Why do I get a DegradedArray event with mdadm

    - by azera
    Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

    Read the article

  • SATA Blu-Ray drive not detected via USB adapter

    - by LTR
    I'm using an SATA blu-ray drive (Lite-On IHOS104), connected via a USB adapter to my Windows 7 (32-bit) notebook. The first time I plugged the adapter in, it worked perfectly. The drive appeared in Explorer, and my player software was able to play an encrypted Blu-Ray disc just fine. After the first reboot, it never worked again. Now it shows up as "removable media" with a size of 0 bytes, irregardless of whether a disk is inserted or not. The drive does not show up under the green "eject USB device" icon in the taskbar. The adapter is powered using a separate power adapter. I have tried: disconnecting all other USB devices testing with a DVD instead of a Blu-Ray disc letting Windows search for updated drivers for the drive - there are none using the same drive and adapter on another Win7 (but x64) computer. They work perfectly. using other USB ports on the same notebook - tried them all. using a different SATA/USB-adapter What else can I do to diagnose this problem?

    Read the article

  • OpenVPN, install a TAP adapter

    - by GolezTrol
    When I try to connect to my work VPN using OpenVPN, the connection fails with the message: All TAP-Win32 adapters on this system are currently in use. Many sources suggest to look in Control Panel\Network and Internet\Network Connections an enable the TAP adapter, but when I look there, there is none. Now I've run addtap.bat which is provided with OpenVPN, but I still don't get to see any TAP adapter, and logging in in VPN still fails. The output of addtap.bat is C:\Windows\system32>"C:\Program Files (x86)\OpenVPN\bin\tapinstall.exe" install "C:\Program Files (x86)\OpenVPN\driver\OemWin2k.inf" tap0801 Device node created. Install is complete when drivers are updated... Updating drivers for tap0801 from C:\Program Files (x86)\OpenVPN\driver\OemWin2k .inf. Drivers updated successfully. I've Run As Administrator both the setup of OpenVPN and addtap.bat. I've run deltapall.bat to remove any (maybe hidden) adapters. It said it removed three of them, after which I ran addtap.bat again to try to create another one. I also run OpenVPN itself as administrator. What's wrong? Running Windows 7 Home Premium on a HP Pavilion dv7 4050ed. It has worked before, but I recently had to reinstall my laptop, for which I used the restore disks I created when I just got it. Everything else seems to work fine. == UPDATE == The TAP adapter is found in Device Manager, but apparently it is disabled because it is incompatible with Windows 7 64bit. I've deïnstalled OpenVPNGui, downloaded a version that should be 64bit compatible, and installed that. Still no cigar. Then I found a tip to install OpenVPN (version 9) after installing OpenVPNGui, because that installs OpenVPN version 8. Now I got a v9 TAP driver in Device Manager, but it still doesn't work and shows up in device manager with an exclamation mark, and not at all in my network devices.

    Read the article

  • Abysmal transfer speeds on gigabit network

    - by Vegard Larsen
    I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

    Read the article

  • I can't connect to my network, except in safe mode

    - by eidylon
    My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

    Read the article

  • APC Smart UPS network shutdown issue

    - by Rob Clarke
    Here is a bit about our setup: We have 2x Smart-UPS RT 6000 XL units with network management cards We are running Powerchute from a network server Powerchute is connected to the management cards of both UPSs UPSs are set to do a graceful shutdown via Powerchute when the battery duration is under 20 minutes We also have a command file that runs with Powerchute Although our setup is redundant we do not have an equal load on each server due to APC switches for single power devices The problem is that as we do not have an equal load on each server the batteries drain at different rates. This means that the UPSs both get to the specified low battery duration at completely different times. The problem here is that UPS 1 may have run down to 5 minutes and is in desperate need of initiating a Powerchute shutdown - UPS 2 still has 25 minutes of runtime so no shutdown is initiated. Consequently UPS 1 goes down and takes all the servers with and then shuts down UPS 2 as well! What we need to happen are 1 of either 2 things: Powerchute initiates the shutdown as soon as either UPS reaches the 20 minutes low battery duration setting - and doesnt wait for both The UPS with the heavier load expends its entire battery but does not shutdown both UPSs and lets the load be switched across to the UPS that still has runtime remaining. That way when the UPS that still has runtime reaches its low battery duration it can proceed with the graceful shutdown via Powerchute. Hope that makes sense, any help is greatly appreciated!

    Read the article

  • Windows 7 fails to install

    - by Brian Ortiz
    I'm upgrading from Vista SP1 (which was actually upgraded from XP over a year ago) to Windows 7 RTM (64-bit Ultimate to 64-bit Ultimate). After 4 hours or so, the install fails with the message "This version of Windows could not be installed, Your previous version of Windows has been restored, and you can continue to use it." This error is back at my Vista desktop, there's no error that I could see during install, I just a message indicating that it was reverting everything. I tracked down the error logs and here's the log at I uploaded the error log (from C:\$WINDOWS.~BT\Sources\Panther) and uploaded onto Pastebin. Here is an excerpt: 2009-08-09 02:54:57, Error Number of Enumerated Devices = 21[gle=0x00000103] 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x[gle=0x80092004] 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x[gle=0x80092004] It was suggested that I upgrade to SP2 before upgrading to Vista, but this made no difference. I since uninstalled SP2 since it was creating some problems with a piece of hardware. I know a fresh install is best, but I'm hoping to avoid that because I'd need a new hard drive. Per Reuben's instruction, I found the install's dump and uploaded it here. (266 KB)

    Read the article

  • Microsoft Windows DHCP: Steering IPv4 clients into specific scopes based on MAC

    - by Easter Sunshine
    We have visitors on our campus who bring their own laptops and devices and use our wireless and wired networks. When we receive a copyright infringement notice (typically BitTorrenting), we are required to quarantine that MAC address so that it no longer has Internet access. No matter what website it tries to visit, it is sent to a web page explaining to the user that the device has been quarantined. We have thus far implemented this in ISC DHCP on Linux. We have multiple VLANs with one or more public-IP subnets and one RFC1918 quarantine subnet each. All clients are leased IPs in the public-IP subnet(s) unless you're in a list of known bad MACs. Then, you are sent to the quarantine subnet so that your traffic is unroutable on the Internet (you are isolated by subnet only, not by VLAN). We would like to move to Windows DHCP in light of the IPAM role but I cannot figure out how to replicate this in Windows DHCP 2012 (Assign DHCP IPs for specific MAC prefixes on Windows Server 2008 R2 suggests it was not possible in 2008 R2), even while using policies. So here's what I'd like: The administrator/help desk provides and maintains a list of MAC addresses that are to be quarantined. The DHCP server places those MACs into the quarantine subnet on the respective VLAN, no matter which VLAN the client is in. I don't think reservations would work: We currently have about 300 registered bad MACs and about 12 VLANs. I don't want to make 300 x 12 reservations nor have to add 12 reservations per new MAC address. Not to mention all of the quarantine subnets are /24s. We do not have NPS/NAC. You do not have to register your MAC address get network access. We use Cisco routers/switches. Thanks.

    Read the article

< Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >