Search Results

Search found 12751 results on 511 pages for 'interface'.

Page 173/511 | < Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >

• How do I get wireless working on a Dell Inspiron 510m?

  - by user17449

  Why WiFi don't work in my Dell Inspiron 510m with Ubuntu 10.04? Is that usefull? inspiron@Inspiron:~$ rfkill list all inspiron@Inspiron:~$ sudo lshw -C network [sudo] password for inspiron: *-network:0 DISABLED description: Wireless interface product: PRO/Wireless LAN 2100 3B Mini PCI Adapter vendor: Intel Corporation physical id: 3 bus info: pci@0000:01:03.0 logical name: eth1 version: 04 serial: 00:0c:f1:5b:5d:40 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ipw2100 driverversion=git-1.2.2 firmware=712.0.3:3:00000001 latency=32 link=no maxlatency=34 mingnt=2 multicast=yes wireless=unassociated resources: irq:5 memory:fcffe000-fcffefff *-network:1 description: Ethernet interface product: 82801DB PRO/100 VE (MOB) Ethernet Controller vendor: Intel Corporation physical id: 8 bus info: pci@0000:01:08.0 logical name: eth0 version: 81 serial: 00:11:43:41:d8:b8 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half firmware=N/A ip=192.168.0.2 latency=32 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10MB/s resources: irq:11 memory:fcffd000-fcffdfff ioport:ecc0(size=64) inspiron@Inspiron:~$ iwconfig wlan0 wlan0 No such device inspiron@Inspiron:~$ ifconfig -a eth0 Link encap:Ethernet Endereço de HW 00:11:43:41:d8:b8 inet end.: 192.168.0.2 Bcast:192.168.0.255 Masc:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet Endereço de HW 00:0c:f1:5b:5d:40 BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) IRQ:5 Endereço de E/S:0xe000 Memória:fcffe000-fcffefff lo Link encap:Loopback Local inet end.: 127.0.0.1 Masc:255.0.0.0 endereço inet6: ::1/128 Escopo:Máquina UP LOOPBACK RUNNING MTU:16436 Métrica:1 pacotes RX:628 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:628 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:0 RX bytes:50104 (50.1 KB) TX bytes:50104 (50.1 KB) inspiron@Inspiron:~$ nm-tool NetworkManager Tool State: connected - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: ipw2100 State: unavailable Default: no HW Address: 00:0C:F1:5B:5D:40 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: e100 State: unmanaged Default: no HW Address: 00:11:43:41:D8:B8 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: off inspiron@Inspiron:~$

  Read the article

• Wireless Broadcom 4313 not working on Ubuntu 12.04

  - by user88568

  It seems a lot of people are having this problem, but none of the posted solutions have worked for me so far. My driver is installed and activated, I have tried removing and re-adding the network, and various other fixes. No networks were picked up on my first boot, the next day wireless worked fine, and since then it does not detect networks, and when I manually try to connect, it repeatedly asks for the password and does not connect. Here's my info: 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f0500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-a1-ff-ff-f3-70-f1 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac root@michelle-laptop:/home/michelle# ifconfig eth0 Link encap:Ethernet HWaddr 70:f1:a1:f3:ba:ab inet6 addr: fe80::72f1:a1ff:fef3:baab/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:29 TX packets:0 errors:30 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 eth1 Link encap:Ethernet HWaddr f0:4d:a2:53:83:7a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:104 errors:0 dropped:0 overruns:0 frame:0 TX packets:104 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8000 (8.0 KB) TX bytes:8000 (8.0 KB) root@michelle-laptop:/home/michelle# lsmod Module Size Used by dm_crypt 22528 0 snd_hda_codec_hdmi 31775 1 snd_hda_codec_realtek 174313 1 snd_hda_intel 32765 5 snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80845 4 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 lib80211_crypt_tkip 17275 0 bnep 17830 2 rfcomm 38139 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq joydev 17393 0 wl 2646601 0 snd 62064 19 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd btusb 17912 0 bluetooth 158438 11 bnep,rfcomm,btusb uvcvideo 67203 0 videodev 86588 1 uvcvideo snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lib80211 14040 2 lib80211_crypt_tkip,wl intel_ips 17822 0 psmouse 72919 0 serio_raw 13027 0 mei 36570 0 dell_laptop 17767 0 dell_wmi 12601 0 dcdbas 14098 1 dell_laptop sparse_keymap 13658 1 dell_wmi mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid wmi 18744 1 dell_wmi i915 414817 3 atl1c 36718 0 drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 root@michelle-laptop:/home/michelle# iwlist scan lo Interface doesn't support scanning. eth1 Interface doesn't support scanning. eth0 No scan results root@michelle-laptop:/home/michelle# rfkill list 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no Obviously I don't know what I'm doing. I'd appreciate any help! Thanks!

  Read the article

• Send raw data to USB parallel port after upgrading to 11.10

  - by zaphod

  I have a laser cutter connected via a generic USB to parallel adapter. The laser cutter speaks HPGL, as it happens, but since this is a laser cutter and not a plotter, I usually want to generate the HPGL myself, since I care about the ordering, speed, and direction of cuts and so on. In previous versions of Ubuntu, I was able to print to the cutter by copying an HPGL file directly to the corresponding USB "lp" device. For example: cp foo.plt /dev/usblp1 Well, I just upgraded to Ubuntu 11.10 oneiric, and I can't find any "lp" devices in /dev anymore. D'oh! What's the preferred way to send raw data to a parallel port in Ubuntu? I've tried System Settings Printing + Add, hoping that I might be able to associate my device with some kind of "raw printer" driver and print to it with a command like lp -d LaserCutter foo.plt But my USB to parallel adapter doesn't seem to show up in the list. What I do see are my HP Color LaserJet, two USB-to-serial adapters, "Enter URI", and "Network Printer". Meanwhile, over in /dev, I do see /dev/ttyUSB0 and /dev/ttyUSB1 devices for the 2 USB-to-serial adapters. I don't see anything obvious corresponding to the HP printer (which was /dev/usblp0 prior to the upgrade), except for generic USB stuff. For example, sudo find /dev | grep lp produces no output. I do seem to be able to print to the HP printer just fine, though. The printer setup GUI gives it a device URI starting with "hp:" which isn't much help for the parallel adapter. The CUPS administrator's guide makes it sound like I might need to feed it a device URI of the form parallel:/dev/SOMETHING, but of course if I had a /dev/SOMETHING I'd probably just go on writing to it directly. Here's what dmesg says after I disconnect and reconnect the device from the USB port: [ 924.722906] usb 1-1.1.4: USB disconnect, device number 7 [ 959.993002] usb 1-1.1.4: new full speed USB device number 8 using ehci_hcd And here's how it shows up in lsusb -v: Bus 001 Device 008: ID 1a86:7584 QinHeng Electronics CH340S Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x1a86 QinHeng Electronics idProduct 0x7584 CH340S bcdDevice 2.52 iManufacturer 0 iProduct 2 USB2.0-Print iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 96mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Device Status: 0x0000 (Bus Powered)

  Read the article

• C#/.NET Little Wonders: Comparer&lt;T&gt;.Default

  - by James Michael Hare

  I’ve been working with a wonderful team on a major release where I work, which has had the side-effect of occupying most of my spare time preparing, testing, and monitoring.  However, I do have this Little Wonder tidbit to offer today. Introduction The IComparable<T> interface is great for implementing a natural order for a data type.  It’s a very simple interface with a single method: 1: public interface IComparer<in T> 2: { 3: // Compare two instances of same type. 4: int Compare(T x, T y); 5: }  So what do we expect for the integer return value?  It’s a pseudo-relative measure of the ordering of x and y, which returns an integer value in much the same way C++ returns an integer result from the strcmp() c-style string comparison function: If x == y, returns 0. If x > y, returns > 0 (often +1, but not guaranteed) If x < y, returns < 0 (often –1, but not guaranteed) Notice that the comparison operator used to evaluate against zero should be the same comparison operator you’d use as the comparison operator between x and y.  That is, if you want to see if x > y you’d see if the result > 0. The Problem: Comparing With null Can Be Messy This gets tricky though when you have null arguments.  According to the MSDN, a null value should be considered equal to a null value, and a null value should be less than a non-null value.  So taking this into account we’d expect this instead: If x == y (or both null), return 0. If x > y (or y only is null), return > 0. If x < y (or x only is null), return < 0. But here’s the problem – if x is null, what happens when we attempt to call CompareTo() off of x? 1: // what happens if x is null? 2: x.CompareTo(y); It’s pretty obvious we’ll get a NullReferenceException here.  Now, we could guard against this before calling CompareTo(): 1: int result; 2:  3: // first check to see if lhs is null. 4: if (x == null) 5: { 6: // if lhs null, check rhs to decide on return value. 7: if (y == null) 8: { 9: result = 0; 10: } 11: else 12: { 13: result = -1; 14: } 15: } 16: else 17: { 18: // CompareTo() should handle a null y correctly and return > 0 if so. 19: result = x.CompareTo(y); 20: } Of course, we could shorten this with the ternary operator (?:), but even then it’s ugly repetitive code: 1: int result = (x == null) 2: ? ((y == null) ? 0 : -1) 3: : x.CompareTo(y); Fortunately, the null issues can be cleaned up by drafting in an external Comparer.  The Soltuion: Comparer<T>.Default You can always develop your own instance of IComparer<T> for the job of comparing two items of the same type.  The nice thing about a IComparer is its is independent of the things you are comparing, so this makes it great for comparing in an alternative order to the natural order of items, or when one or both of the items may be null. 1: public class NullableIntComparer : IComparer<int?> 2: { 3: public int Compare(int? x, int? y) 4: { 5: return (x == null) 6: ? ((y == null) ? 0 : -1) 7: : x.Value.CompareTo(y); 8: } 9: }  Now, if you want a custom sort -- especially on large-grained objects with different possible sort fields -- this is the best option you have.  But if you just want to take advantage of the natural ordering of the type, there is an easier way.  If the type you want to compare already implements IComparable<T> or if the type is System.Nullable<T> where T implements IComparable, there is a class in the System.Collections.Generic namespace called Comparer<T> which exposes a property called Default that will create a singleton that represents the default comparer for items of that type.  For example: 1: // compares integers 2: var intComparer = Comparer<int>.Default; 3:  4: // compares DateTime values 5: var dateTimeComparer = Comparer<DateTime>.Default; 6:  7: // compares nullable doubles using the null rules! 8: var nullableDoubleComparer = Comparer<double?>.Default;  This helps you avoid having to remember the messy null logic and makes it to compare objects where you don’t know if one or more of the values is null. This works especially well when creating say an IComparer<T> implementation for a large-grained class that may or may not contain a field.  For example, let’s say you want to create a sorting comparer for a stock open price, but if the market the stock is trading in hasn’t opened yet, the open price will be null.  We could handle this (assuming a reasonable Quote definition) like: 1: public class Quote 2: { 3: // the opening price of the symbol quoted 4: public double? Open { get; set; } 5:  6: // ticker symbol 7: public string Symbol { get; set; } 8:  9: // etc. 10: } 11:  12: public class OpenPriceQuoteComparer : IComparer<Quote> 13: { 14: // Compares two quotes by opening price 15: public int Compare(Quote x, Quote y) 16: { 17: return Comparer<double?>.Default.Compare(x.Open, y.Open); 18: } 19: } Summary Defining a custom comparer is often needed for non-natural ordering or defining alternative orderings, but when you just want to compare two items that are IComparable<T> and account for null behavior, you can use the Comparer<T>.Default comparer generator and you’ll never have to worry about correct null value sorting again.     Technorati Tags: C#,.NET,Little Wonders,BlackRabbitCoder,IComparable,Comparer

  Read the article

• Building an Infrastructure Cloud with Oracle VM for x86 + Enterprise Manager 12c

  - by Richard Rotter

  Cloud Computing? Everyone is talking about Cloud these days. Everyone is explaining how the cloud will help you to bring your service up and running very fast, secure and with little effort. You can find these kinds of presentations at almost every event around the globe. But what is really behind all this stuff? Is it really so simple? And the answer is: Yes it is! With the Oracle SW Stack it is! In this post, I will try to bring this down to earth, demonstrating how easy it could be to build a cloud infrastructure with Oracle's solution for cloud computing.But let me cover some basics first: How fast can you build a cloud?How elastic is your cloud so you can provide new services on demand? How much effort does it take to monitor and operate your Cloud Infrastructure in order to meet your SLAs?How easy is it to chargeback for your services provided? These are the critical success factors of Cloud Computing. And Oracle has an answer to all those questions. By using Oracle VM for X86 in combination with Enterprise Manager 12c you can build and control your cloud environment very fast and easy. What are the fundamental building blocks for your cloud? Oracle Cloud Building Blocks #1 Hardware Surprise, surprise. Even the cloud needs to run somewhere, hence you will need hardware. This HW normally consists of servers, storage and networking. But Oracles goes beyond that. There are Optimized Solutions available for your cloud infrastructure. This is a cookbook to build your HW cloud platform. For example, building your cloud infrastructure with blades and our network infrastructure will reduce complexity in your datacenter (Blades with switch network modules, splitter cables to reduce the amount of cables, TOR (Top Of the Rack) switches which are building the interface to your infrastructure environment. Reducing complexity even in the cabling will help you to manage your environment more efficient and with less risk. Of course, our engineered systems fit into the cloud perfectly too. Although they are considered as a PaaS themselves, having the database SW (for Exadata) and the application development environment (for Exalogic) already deployed on them, in general they are ideal systems to enable you building your own cloud and PaaS infrastructure. #2 Virtualization The next missing link in the cloud setup is virtualization. For me personally, it's one of the most hidden "secret", that oracle can provide you with a complete virtualization stack in terms of a hypervisor on both architectures: X86 and Sparc CPUs. There is Oracle VM for X86 and Oracle VM for Sparc available at no additional  license costs if your are running this virtualization stack on top of Oracle HW (and with Oracle Premier Support for HW). This completes the virtualization portfolio together with Solaris Zones introduced already with Solaris 10 a few years ago. Let me explain how Oracle VM for X86 works: Oracle VM for x86 consists of two main parts: - The Oracle VM Server: Oracle VM Server is installed on bare metal and it is the hypervisor which is able to run virtual machines. It has a very small footprint. The ISO-Image of Oracle VM Server is only 200MB large. It is very small but efficient. You can install a OVM-Server in less than 5 mins by booting the Server with the ISO-Image assigned and providing the necessary configuration parameters (like installing an Linux distribution). After the installation, the OVM-Server is ready to use. That's all. - The Oracle VM-Manager: OVM-Manager is the central management tool where you can control your OVM-Servers. OVM-Manager provides the graphical user interface, which is an Application Development Framework (ADF) application, with a familiar web-browser based interface, to manage Oracle VM Servers, virtual machines, and resources. The Oracle VM Manager has the following capabilities: Create virtual machines Create server pools Power on and off virtual machines Manage networks and storage Import virtual machines, ISO files, and templates Manage high availability of Oracle VM Servers, server pools, and virtual machines Perform live migration of virtual machines I want to highlight one of the goodies which you can use if you are running Oracle VM for X86: Preconfigured, downloadable Virtual Machine Templates form edelivery With these templates, you can download completely preconfigured Virtual Machines in your environment, boot them up, configure them at first time boot and use it. There are templates for almost all Oracle SW and Applications (like Fusion Middleware, Database, Siebel, etc.) available. #3) Cloud Management The management of your cloud infrastructure is key. This is a day-to-day job. Acquiring HW, installing a virtualization layer on top of it is done just at the beginning and if you want to expand your infrastructure. But managing your cloud, keeping it up and running, deploying new services, changing your chargeback model, etc, these are the daily jobs. These jobs must be simple, secure and easy to manage. The Enterprise Manager 12c Cloud provides this functionality from one management cockpit. Enterprise Manager 12c uses Oracle VM Manager to control OVM Serverpools. Once you registered your OVM-Managers in Enterprise Manager, then you are able to setup your cloud infrastructure and manage everything from Enterprise Manager. What you need to do in EM12c is: ">Register your OVM Manager in Enterprise ManagerAfter Registering your OVM Manager, all the functionality of Oracle VM for X86 is also available in Enterprise Manager. Enterprise Manager works as a "Manger" of the Manager. You can register as many OVM-Managers you want and control your complete virtualization environment Create Roles and Users for your Self Service Portal in Enterprise ManagerWith this step you allow users to logon on the Enterprise Manager Self Service Portal. Users can request Virtual Machines in this portal. Setup the Cloud InfrastructureSetup the Quotas for your self service users. How many VMs can they request? How much of your resources ( cpu, memory, storage, network, etc. etc.)? Which SW components (templates, assemblys) can your self service users request? In this step, you basically set up the complete cloud infrastructure. Setup ChargebackOnce your cloud is set up, you need to configure your chargeback mechanism. The Enterprise Manager collects the resources metrics, which are used in a very deep level. Almost all collected Metrics could be used in the chargeback module. You can define chargeback plans based on configurations (charge for the amount of cpu, memory, storage is assigned to a machine, or for a specific OS which is installed) or chargeback on resource consumption (% of cpu used, storage used, etc). Or you can also define a combination of configuration and consumption chargeback plans. The chargeback module is very flexible. Here is a overview of the workflow how to handle infrastructure cloud in EM: Summary As you can see, setting up an Infrastructure Cloud Service with Oracle VM for X86 and Enterprise Manager 12c is really simple. I personally configured a complete cloud environment with three X86 servers and a small JBOD san box in less than 3 hours. There is no magic in it, it is all straightforward. Of course, you have to have some experience with Oracle VM and Enterprise Manager. Experience in setting up Linux environments helps as well. I plan to publish a technical cookbook in the next few weeks. I hope you found this post useful and will see you again here on our blog. Any hints, comments are welcome!

  Read the article

• Thread travailleur avec Qt en utilisant les signaux et les slots, un article de Christophe Dumez traduit par Thibaut Cuvelier

  Qt fournit des classes de threads indépendantes de la plateforme, une manière thread-safe de poster des événements et des connexions entre signaux et slots entre les threads. La programmation multithreadée s'avantage des machines à plusieurs processeurs et est aussi utile pour effectuer les opérations chronophages sans geler l'interface utilisateur d'une application. Sans multithreading, tout est fait dans le thread principal.

  Read the article

• How to sync audio files with Logitech media server in MAC OS?

  - by Abhishek

  I want to customize the Logitech Media Server (web interface on localhost) so that N number of DIFFERENT audio files will start to play at the same time on N number of wifi receivers, each file on a different receiver. Currently, the server will sync only 1 track to N number(amount) of receivers. Is it possible with Logitech media server is open source. How can I able to do this? can you explain me sample code?

  Read the article

• Suggestions for connecting .NET WPF GUI with Java SE Server aoo

  - by Sam Goldberg

  BACKGROUND We are building a Java (SE) trading application which will be monitoring market data and sending trade messages based on the market data, and also on user defined configuration parameters. We are planning to provide the user with a thin client, built in .NET (WPF) for managing the parameters, controlling the server behavior, and viewing the current state of the trading. The client doesn't need real-time updates; it will instead update the view once every few seconds (or whatever interval is configured by the user). The client has about 6 different operations it needs to perform with the server, for example: CRUD with configuration parameters query subset of the data receive updates of current positions from server It is possible that most of the different operations (except for receiving data) are just different flavors of managing the configuration parameters, but it's too early in our analysis for us to be sure. To connect the client with the server, we have been considering using: SOAP Web Service RESTful service building a custom TCP/IP based API (text or xml) (least preferred - but we use this approach with other applications we have) As best as I understand, pros and cons of the different web service flavors are: SOAP pro: totally automated in .NET (and Java), modifying server side interface require no code changes in communication layer, just running refresh on Web Service reference to regenerate the classes. con: more overhead in the communication layer sending more text, etc. We're not using J2EE container so maybe doesn't work so well with J2SE REST pro: lighter weight, less data. Has good .NET and Java support. (I don't have any real experience with this, so don't know what other benefits it has.) con: client will not be automatically aware if there are any new operations or properties added (?), so communication layer needs to be updated by developer if server interface changes. con: (both approaches) Server cannot really push updates to the client at regular intervals (?) (However, we won't mind if client polls the server to get updates.) QUESTION What are your opinions on the above options or suggestions for other ways to connect the 2 parts? (Ideally, we don't want to put much work into the communication layer, because it's not the significant part of the application so the more off-the-shelf and automated the better.)

  Read the article

• Ubuntu 14.04 : Lost my sound randomly tried a few commands and I think I failed

  - by Marc-Antoine Théberge

  I lost my sound the other day and I tried to delete pulseaudio then reinstall, then I tried to delete it and install alsa, It did not work and I had to reinstall everything; overall bad idea... now I can't have any sound. Should I do a fresh install? I don't know how to boot an usb drive with GRUB... Here's my sysinfo System information report, generated by Sysinfo: 2014-05-28 05:45:58 http://sourceforge.net/projects/gsysinfo SYSTEM INFORMATION Running Ubuntu Linux, the Ubuntu 14.04 (trusty) release. GNOME: 3.8.4 (Ubuntu 2014-03-17) Kernel version: 3.13.0-27-generic (#50-Ubuntu SMP Thu May 15 18:08:16 UTC 2014) GCC: 4.8 (i686-linux-gnu) Xorg: 1.15.1 (16 April 2014 01:40:08PM) (16 April 2014 01:40:08PM) Hostname: mark-laptop Uptime: 0 days 11 h 43 min CPU INFORMATION GenuineIntel, Intel(R) Atom(TM) CPU N270 @ 1.60GHz Number of CPUs: 2 CPU clock currently at 1333.000 MHz with 512 KB cache Numbering: family(6) model(28) stepping(2) Bogomips: 3192.13 Flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 xtpr pdcm movbe lahf_lm dtherm MEMORY INFORMATION Total memory: 2007 MB Total swap: 1953 MB STORAGE INFORMATION SCSI device - scsi0 Vendor: ATA Model: ST9160310AS HARDWARE INFORMATION MOTHERBOARD Host bridge Intel Corporation Mobile 945GSE Express Memory Controller Hub (rev 03) Subsystem: ASUSTeK Computer Inc. Device 8340 PCI bridge(s) Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode]) ISA bridge Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) Subsystem: ASUSTeK Computer Inc. Device 830f IDE interface Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 02) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 830f GRAPHIC CARD VGA controller Intel Corporation Mobile 945GSE Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 8340 SOUND CARD Multimedia controller Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) Subsystem: ASUSTeK Computer Inc. Device 831a NETWORK Ethernet controller Qualcomm Atheros AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: ASUSTeK Computer Inc. Device 8324

  Read the article

• Display Driver Issue on an hp TX2-1160ea Notebook

  - by Sam

  I'm new to Linux and recently switched to Ubuntu 11.04 due to my project requirement. My laptop has been freezing and going to black screen of death when I run anything related to display (Share desktop, stream video, etc). Today I went through the Ubuntu forum to install the appropriate graphic driver and, after doing it, I rebooted my PC. It gave an error before login saying "select the recovery mode" and after clicking OK, it didn't give the same error on reboot but I've lost the 11.04 graphical interface and all I see is the interface of Ubuntu v10 with slow visuals (even scrolling up/down on browser is really slow). For the reference, here's a desktop screenshot so that you can understand the situation. Also the laptop is overheating. How can I fix this problem? How can i get the Ubuntu 11.04 view back? I also tried Google, but couldn't find any issue like this. Some general Information: Laptop: HP TouchSmart TX2-1160ea Processor: AMD Turion TX2 Memory: 4GB OS: Ubuntu 11.04 Some debugging information:: $ report-hw | grep controller lspci -knn: 00:11.0 SATA controller [0106]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] lspci -knn: 00:14.3 ISA bridge [0601]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] lspci -knn: 01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS780M/RS780MN [Radeon HD 3200 Graphics] [1002:9612] lspci -knn: 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) lspci -knn: 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02) And: $ dpkg -l '*fglrx*' Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-==============-==============-============================================ ii fglrx 2:8.840-0ubunt Video driver for the ATI graphics accelerato ii fglrx-amdcccle 2:8.840-0ubunt Catalyst Control Center for the ATI graphics un fglrx-control <none> (no description available) un fglrx-control- <none> (no description available) ii fglrx-dev 2:8.840-0ubunt Video driver for the ATI graphics accelerato un fglrx-driver <none> (no description available) un fglrx-driver-d <none> (no description available) un fglrx-kernel-s <none> (no description available) un fglrx-modalias <none> (no description available) un xfree86-driver <none> (no description available) un xfree86-driver <none> (no description available) un xorg-driver-fg <none> (no description available) un xorg-driver-fg <none> (no description available) If you need any more information that could help, just ask.

  Read the article

• Enhance your Queries with Stored Functions

  HeidiSQL 4's Stored Routine Editor offers a user-friendly alternative to using a command-line interface to create and manage your stored procedures and functions. Today, we'll be learning how to take advantage of some useful native MySQL functions as well as use the editor to create our own custom functions.

  Read the article

• Translating Your Customizations

  - by Richard Bingham

  This blog post explains the basics of translating the customizations you can make to Fusion Applications products, with the inclusion of information for both composer-based customizations and the generic design-time customizations done via JDeveloper. Introduction Like most Oracle Applications, Fusion Applications installs on-premise with a US-English base language that is, in Release 7, supported by the option to add up to a total of 22 additional language packs (In Oracle Cloud production environments languages are pre-installed already). As such many organizations offer their users the option of working with their local language, and logically that should also apply for any customizations as well. Composer-based UI Customizations Customizations made in Page Composer take into consideration the session LOCALE, as set in the user preferences screen, during all customization work, and stores the customization in the MDS repository accordingly. As such the actual new or changed values used will only apply for the same language under which the customization was made, and text for any other languages requires a separate upload. See the Resource Bundles section below, which incidentally also applies to custom UI changes done in JDeveloper. You may have noticed this when you select the “Select Text Resource” menu option when editing the text on a page. Using this ensures that the resource bundles are used, whereas if you define a static value in Expression Builder it will never be available for translation. Notice in the screenshot below the “What’s New” custom value I have already defined using the ‘Select Text Resource’ feature is internally using the adfBundle groovy function to pull the custom value for my key (RT_S_1) from the ComposerOverrideBundle. Figure 1 – Page Composer showing the override bundle being used. Business Objects Customizing the Business Objects available in the Applications Composer tool for the CRM products, such as adding additional fields, also operates using the session language. Translating these additional values for these fields into other installed languages requires loading additional resource bundles, again as described below. Reports and Analytics Most customizations to Reports and BI Analytics are just essentially reorganizations and visualizations of existing number and text data from the system, and as such will use the appropriate values based on the users session language. Where a translated value or string exists for that session language, it will be used without the need for additional work. Extending through the addition of brand new reports and analytics requires another method of loading the translated strings, as part of what is known as ‘Localizing’ the BI Catalog and Metadata. This time it is via an export/import of XML data through the BI Administrators console, and is described in the OBIEE Admin Guide. Fusion Applications reports based on BI Publisher are already defined in template-per-locale, and in addition provide an extra process for getting the data for translation and reloading. This again uses the standard resource bundle format. Loading a custom report is illustrated in this video from our YouTube channel which shows the screen for both setting the template local and running an export for translation. Fusion Applications Menus Whilst the seeded Navigator and Global Menu values are fully translated when the additional language is installed, if they are customized then the change or new menu item will apply universally, not currently per language. This is set to change in a future release with the new UI Text Editor feature described below. More on Resource Bundles As mentioned above, to provide translations for most of your customizations you need to add values to a resource bundle. This is an industry open standard (OASIS) format XML file with the extension .xliff, and store translated values for the strings used by ADF at run-time. The general process is that these values are exported from the MDS repository, manually edited, and then imported back in again.This needs to be done by an administrator, via either WLST commands or through Enterprise Manager as per the screenshot below. This is detailed out in the Fusion Applications Extensibility Guide. For SaaS environments the Cloud Operations team can assist. Figure 2 – Enterprise Manager’s MDS export used getting resource bundles for manual translation and re-imported on the same screen. All customized strings are stored in an override bundle (xliff file) for each locale, suffixed with the language initials, with English ones being saved to the default. As such each language bundle can be easily identified and updated. Similarly if you used JDeveloper to create your own applications as extensions to Fusion Applications you would use the native support for resource bundles, and add them into the faces-config.xml file for inclusion in your application. An example is this ADF customization video from our YouTube channel. JDeveloper also supports automatic synchronization between your underlying resource bundles and any translatable strings you add – very handy. For more information see chapters on “Using Automatic Resource Bundle Integration in JDeveloper” and “Manually Defining Resource Bundles and Locales” in the Oracle Fusion Middleware Web User Interface Developer’s Guide for Oracle Application Development Framework. FND Messages and Look-ups FND Messages, as defined here, are not used for UI labels (they are known as ‘strings’), but are the responses back to users as a result of an action, such as from a page submit. Each ‘message’ is defined and stored in the related database table (FND_MESSAGES_B), with another (FND_MESSAGES_TL) holding any language-specific values. These come seeded with the additional language installs, however if you customize the messages via the “Manage Messages” task in Functional Setup Manager, or add new ones, then currently (in Release 7) you’ll need to repeat it for each language. Figure 3 – An FND Message defined in an English user session. Similarly Look-ups are stored in a translation table (FND_LOOKUP_VALUES_TL) where appropriate, and can be customized by setting the users session language and making the change  in the Setup and Maintenance task entitled “Manage [Standard|Common] Look-ups”. Online Help Yes, in fact all the seeded help is applied as part of each language pack install as part of the post-install provisioning process. If you are editing or adding custom online help then the Create Help screen provides a drop-down of which language your help customization will apply to. This is shown in the video below from our YouTube channel, and obviously you’ll need to it for each language in use. What is Coming for Translations? Currently planned for Release 8 is something called the User Interface (UI) Text Editor. This tool will allow the editing of all the text shown on the pages and forms of Fusion Application. This will provide a search based on a particular term or word, say “Worker”, and will allow it to be adjusted, say to “Employee”, which then updates all the Resource Bundles that contain it. In the case of multi-language environments, it will use the users session language (locale) to know which Resource Bundles to apply the change to. This capability will also support customization sandboxes, to help ensure changes can be tested and approved.  It is also interesting to note that the design currently allows any page-specific customizations done using Page Composer or Application Composer to over-write the global changes done via the UI Text Editor, allowing for special context-sensitive values to still be used. Further Reading and Resources The following short list provides the mains resources for digging into more detail on translation support for both Composer and JDeveloper customization projects. There is a dedicated chapter entitled “Translating Custom Text” in the Fusion Applications Extensibility Guide. This has good examples and steps for many tasks, especially administering resource bundles. Using localization formatting (numbers, dates etc) for design-time changes is well documented in the Fusion Applications Developer Guide. For more guidelines on general design-time globalization, see either the ‘Internationalizing and Localizing Pages’ chapter in the Oracle Fusion Middleware Web User Interface Developer’s Guide for Oracle Application Development Framework (Oracle Fusion Applications Edition) or the general Oracle Database Globalization Support Guide. The Oracle Architecture ‘A-Team’ provided a recent post on customizing the user session timeout popup, using design-time changes to resource bundles. It has detailed step-by-step examples which can be a useful illustration.

  Read the article

• How dependecy injection increases coupling?

  - by B?????

  Reading wiki page on Dependency injection, the disadvantages section tells this : Dependency injection increases coupling by requiring the user of a subsystem to provide for the needs of that subsystem. with a link to an article against DI. What DI does is that it makes a class use the interface instead of the concrete implementation. That should be decreased coupling, no? So, what am I missing? How is dependency injection increasing coupling between classes?

  Read the article

• Wireless not working on Dell Inspirion 1501 after upgrading to Ubuntu 12.04 tried steps in other threads

  - by mark burton

  I updated to Ubuntu 12.04 and now my wireless is not working. No icon for it. Tried some of the troubleshooting in other threads but can't get it to work. Would really appreciate any help Thanks! " *-network description: Network controller product: BCM4311 802.11a/b/g vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:c0200000-c0203fff *-network description: Ethernet interface product: BCM4401-B0 100Base-TX vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 02 serial: 00:19:b9:5c:d1:52 size: 100Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=10.0.0.6 latency=64 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:21 memory:c0300000-c0301fff " lsub results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c526 Logitech, Inc. Nano Receiver $ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:05.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:06.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS482 [Radeon Xpress 200M] 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01) 08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 08:01.0 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 08:01.1 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01) rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• What are these errors when I try to "make" the driver of my wireless adapter?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• Library to fake intermittent failures according to tester-defined policy?

  - by crosstalk

  I'm looking for a library that I can use to help mock a program component that works only intermittently - usually, it works fine, but sometimes it fails. For example, suppose I need to read data from a file, and my program has to avoid crashing or hanging when a read fails due to a disk head crash. I'd like to model that by having a mock data reader function that returns mock data 90% of the time, but hangs or returns garbage otherwise. Or, if I'm stress-testing my full program, I could turn on debugging code in my real data reader module to make it return real data 90% of the time and hang otherwise. Now, obviously, in this particular example I could just code up my mock manually to test against a random() routine. However, I was looking for a system that allows implementing any failure policy I want, including: Fail randomly 10% of the time Succeed 10 times, fail 4 times, repeat Fail semi-randomly, such that one failure tends to be followed by a burst of more failures Any policy the tester wants to define Furthermore, I'd like to be able to change the failure policy at runtime, using either code internal to the program under test, or external knobs or switches (though the latter can be implemented with the former). In pig-Java, I'd envision a FailureFaker interface like so: interface FailureFaker { /** Return true if and only if the mocked operation succeeded. Implementors should override this method with versions consistent with their failure policy. */ public boolean attempt(); } And each failure policy would be a class implementing FailureFaker; for example there would be a PatternFailureFaker that would succeed N times, then fail M times, then repeat, and a AlwaysFailFailureFaker that I'd use temporarily when I need to simulate, say, someone removing the external hard drive my data was on. The policy could then be used (and changed) in my mock object code like so: class MyMockComponent { FailureFaker faker; public void doSomething() { if (faker.attempt()) { // ... } else { throw new RuntimeException(); } } void setFailurePolicy (FailureFaker policy) { this.faker = policy; } } Now, this seems like something that would be part of a mocking library, so I wouldn't be surprised if it's been done before. (In fact, I got the idea from Steve Maguire's Writing Solid Code, where he discusses this exact idea on pages 228-231, saying that such facilities were common in Microsoft code of that early-90's era.) However, I'm only familiar with EasyMock and jMockit for Java, and neither AFAIK have this function, or something similar with different syntax. Hence, the question: Do such libraries as I've described above exist? If they do, where have you found them useful? If you haven't found them useful, why not?

  Read the article

• Ubuntu Server Cannot Route to the Internet

  - by ejes

  I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

  Read the article

• wifi connection in lubuntu 11.10

  - by made_in_india

  I am facing the wifi network connection problem, which was previously working absolutely fine. I have checked /etc/network/interfaces file auto wlan0 iface wlan0 inet dhcp wireless-mode managed wireless-essid my_network_name I have also tried the following command on terminal but were no use sudo ifup wlan0 fail to bring up wlan0 sudo ifdown wlan0 ifdown: interface wlan0 not configured output of $ sudo lspci |grep -i network has produce the below results 06:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Software Architecture and MEF composition location

  - by Leonardo

  Introduction My software (a bunch of webapi's) consist of 4 projects: Core, FrontWebApi, Library and Administration. Library is a code library project that consists of only interfaces and enumerators. All my classes in other projects inherit from at least one interface, and this interface is in the library. Generally speaking, my interfaces define either Entities, Repositories or Controllers. This project references no other project or any special dlls... just the regular .Net stuff... Core is a class-library project where concrete implementation of Entities and Repositories. In some cases i have more than 1 implementation for a Repository (ex: one for azure table storage and one for regular Sql). This project handles the intelligence (business rules mostly) and persistence, and it references only the Library. FrontWebApi is a ASP.NET MVC 4 WebApi project that implements the controllers interfaces to handle web-requests (from a mobile native app)... It references the Core and the Library. Administration is a code-library project that represents a "optional-module", meaning: if it is present, it provides extra-features (such as Access Control Lists) to the application, but if its not, no problem. Administration is also only referencing the Library and implementing concrete classes of a few interfaces such as "IAccessControlEntry"... I intend to make this available with a "setup" that will create any required database table or anything like that. But it is important to notice that the Core has no reference to this project... Development Now, in order to have a decoupled code I decide to use IoC and because this is a small project, I decided to do it using MEF, specially because of its advertised "composition" capabilities. I arranged all the imports/exports and constructors and everything, but something is quite not perfect in my "mental-visualisation": Main Question Where should I "Compose" the objects? I mean: Technically, the only place where real implementation access is required is in the Repositories, because in order to retrieve data from wherever, entities instances will be necessary, and in all other places. The repositories could also provide a public "GetCleanInstanceOf()" right? Then all other places will be just fine working with the interfaces instead of concrete classes... Secondary Question Should "Administration" implement the concrete object for "IAccessControlGeneralRepository" or the Core should?

  Read the article

• VirtualBox Error

  - by Moein7tl

  I wanna install OS on VirtualBox,but when I wanna to install it,it will return errors: Failed to open a session for the virtual machine Arch. Failed to load VMMR0.r0 (VERR_SUPLIB_WORLD_WRITABLE). Unknown error creating VM (VERR_SUPLIB_WORLD_WRITABLE). Details: Result Code: NS_ERROR_FAILURE (0x80004005) Component: Console Interface: IConsole {515e8e8d-f932-4d8e-9f32-79a52aead882} I'm using ubuntu 11.04. How should I solve it?

  Read the article

• Is there a comprehensive list of mupdf keyboard shortcuts?

  - by Dune

  I like mupdf's speed, but I am exasperated by the lack of documentation and its (unnecessarily) hyper-minimal interface with not a menu bar or context menu in sight. Does there exist a list of keyboard shortcuts for this application? The link to the manual on the official site is dead. I only know of the following shortcuts: fit to width: Shift + w fit to height: Shift + h Please respond with the shortcuts you know.

  Read the article

• How do I show a log analysis in Splunk?

  - by Vinod K

  I have made my ubuntu server a centralized log server...I have splunk installed in the /opt directory of the ubuntu server. I have one of the another machines sending logs to this ubuntu server..In the splunk interface i have added in the network ports as UDP port 514...and also have added in the "file and directory" /var/log. The client has also been configured properly...How do I show analysis of the logs??

  Read the article

• Why does fusion icon not work in Ubuntu 12.04

  - by Peter Bauer

  When I start the compiz fusion icon Application from the shell I get the following output but no icon and no GUI: $ fusion-icon --no-start * Detected Session: gnome * Searching for installed applications... Checking if settings need to be migrated ...no Checking if internal files need to be migrated ...no Backend : gconf Integration : true Profile : default Initializing decor options...done * NVIDIA on Xorg detected, exporting: __GL_YIELD=NOTHING * Using the GTK Interface

  Read the article

• Getting in to smart card programming

  - by Scott Chamberlain

  I have a Compaq nw8440 with a smart card reader that is: Compatible with ISO 7816 compliant Smart Cards. PC/SC interface support I have been interested in smart cards and wanted to start playing around with them. If I wanted to get in to programming smart cards where can I find resources on how to do it, and would I need any additional hardware other than what my laptop provides (besides the cards to program)?

  Read the article

• Screen Tweaker Swaps Windows 7 Logon Screen

  - by Jason Fitzpatrick

  Windows: Free application Screen Tweaker makes it simple to swap out your logon screen wallpaper (as well as tweak other elements of the Windows logon screen). In addition to swapping out the wallpaper you can add and remove buttons, add text, and otherwise tweak the interface. Hit up the link below to grab a free copy. Windows 7 Logon Screen Tweaker [via Freeware Genius] How To Properly Scan a Photograph (And Get An Even Better Image) The HTG Guide to Hiding Your Data in a TrueCrypt Hidden Volume Make Your Own Windows 8 Start Button with Zero Memory Usage

  Read the article

< Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >