Search Results

Search found 60556 results on 2423 pages for 'access list'.

Page 175/2423 | < Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >

• File server share access intermittent/slow/machine unstable: win2kr2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• I need to order a list that is dependant on another list. how to change both lists?

  - by Ben Fossen

  I have a Matlab program that generates a list x = 6.1692 8.1863 5.8092 8.2754 6.0891 the program also outputs another list aspl = 680 637 669 599 693. The two lists are on equal length and the first element in list x is related to the first element in list aspl. I need to graph the two lists but want list aspl to be in order from smallest to largest. How would I go about doing this? If I need to move the first element in aspl to position 4 in the list, then the first element of list x also needs to be moved to position 4 in list x. The numbers above are not important they are just examples, the actual program generates hundereds of numbers. for example x = 6.1692 8.1863 5.8092 8.2754 initially aspl = 680 637 669 599 693 after changing aspl to ascending order this is how x should look. x = 5.8092 8.1863 5.8092 6.1692 8.2754 aspl = 599 637 669 680 693

  Read the article

• how to make css submenu stay put when subpage has been selected.

  - by Ronedog

  I have a css horizontal menu with a menu / submenu display working on the hover, but I would also like to make the submenu options stay put when I've selected that page. The code below shows the submenu on hover, but goes away on mouse out. I'm having some difficulty figuring out how to make my code work to keep the submenu items staying put? How can I do this? Thanks for your help. Here's the HTML: <ul id="menu_nav"> <li> <a href="#" class="button">Home</a> <span> <a href="#">Home Link1</a> <a href="#">Home Link2</a> <a href="#">Home Link3</a> </span> </li> <li> <a href="#" class="button">About Us</a> <span> <a href="#">About Link1</a> <a href="#">About Link2</a> <a href="#">About Link3</a> </span> </li> </ul> Here's the CSS ul#menu_nav { position:relative; float:left; width:790px; padding:0; margin:0; list-style-type:none; background-color:#000099; } ul#menu_nav li {float: left; margin: 0; padding: 0; border-right: 1px solid #555;} ul#menu_nav li a.button { float:left; text-decoration:none; color:white; background-color:#000099; padding:0.2em 0.6em; border-right:1px solid #CCCCCC; font-family: Tahoma; font-size: 11px; font-style: normal; font-weight: bold; position: relative; height: 21px; line-height:1.85em; } ul#menu_nav li a:hover { background-color:#F7F7F7; color:#000099; border-top:1px solid #CCCCCC; } ul#menu_nav li span{ float: left; padding: 15px 0; position: absolute; left: 0; top:25px; display: none; /*--Hide by default--*/ width: 790px; background: #F7F7F7; color: #fff; } ul#menu_nav li:hover span { display: block; } /*--Show subnav on hover--*/ ul#menu_nav li span a { display: inline; } /*--Since we declared a link style on the parent list link, we will correct it back to its original state--*/ ul#menu_nav li span a:hover {text-decoration: underline;} Heres the jquery: $("ul#menu_nav li").hover(function() { //Hover over event on list item $(this).css({ 'background' : '#1376c9'}); //Add background color and image on hovered list item $(this).find("span").show(); //Show the subnav } , function() { //on hover out... $(this).css({ 'background' : 'none'}); //Ditch the background $(this).find("span").hide(); //Hide the subnav });

  Read the article

• Why can't I copy .zip files from a server to a server in a different domain?

  - by Kyralessa

  At work, we're using a Windows Server 2008 R2 VM as our build server. At the end of the build process for any of our projects, we copy the packaged deployment files to a folder on the server where they'll be deployed. (This is done in a batch command by a service account.) For most of our projects, which deploy to a Windows Server 2008 R2 VM, this step goes swimmingly. But for one project, which deploys to a Windows Server 2003 R2 VM which resides in a different domain on our network, the .zip files return "Access is denied" and don't copy, though all of the other files copy correctly. Our sysadmins say they haven't prevented this in group policy or by other means. If I'm logged in the build server as myself and run the copy in the command window, I can't copy the .zip files over either, so it's not just a matter of the service account's permissions. If I log into the 2003 server and then copy from the build server to the 2003 server, using the command window, it works, whether I run as myself or as our service account. Only .zip files cause the "Access is denied" problem. Even a (fake) .exe file copies correctly. All of our other projects have .zip files, and they copy to their 2008 R2 server correctly. Is there a way I can get the Windows Server 2003 R2 VM to accept .zip files copied from our build server?

  Read the article

• Wireless Activity Monitoring for PCI DSS Compliance

  - by dkusleika

  In an effort to be PCI DSS compliant, I took a trustkeeper.net questionnaire. I failed the question that asks Is the presence of wireless access points tested for by using a wireless analyzer at least quarterly or by deploying a wireless IDS/IPS to identify all wireless devices in use? (SAQ #11.1) My only wireless access point is outside my firewall, so even if you cracked my wireless you couldn't get inside my domain (unless you crack that too). My firewall doesn't have IPS and I couldn't tell if it had IDS. I looked around for a wireless analyzer, but what I found was $500, which is a little pricey for my size business. And even if I got it, I'm not sure I would understand what it tells me. Surely there are smaller/less sophisticated businesses that take credit cards and have solved this. My questions are: What are the risks if someone were to crack my wireless? (Could they read all internet traffic? Just wireless traffic? Just use my internet connection?) And what is the best/cheapest way to test my connection point quarterly? Should I buy the $500 analyzer? Domain is Windows Server 2000. Firewall is Sonicwall Pro 2040. Router is 8 port D-link.

  Read the article

• Proxy Settings per Machine not working on windows server 2008 R2 SP1

  - by Anirudh Goel

  i have a very interesting problem and would appreciate any help for it. In my scenario i have scripts which bring up a VM inside a domain. Now i want to enable internet access for all the VM's and they go through a proxy. I interact with the VM's using remote sessions and use the credentials of a user which belogs to the domain administrator group. Now problem is that, i create VM's on the fly and destroy them as well,and the scripts i run during their lifetime require internet access on them.So i cannot statically set the proxy settings thus i used the option of Active Directory Group Policy Management. I initially used the "User Configuration" option and set the proxy, which worked like a charm when ever i log inside the machine. However it doesn't work if i use to remote login to the machine with an account which has not yet logged in to the machine. So i used this link to configure it to work on Per Machine, the group policy has worked fine and it reflects in the browser too. But i am not able to resolve any dns name like http://www.google.com or any internet based site. Any idea what i can do?

  Read the article

• Getting Apache to serve same directory with different authentication over SSL?

  - by Lasse V. Karlsen

  I have set up VisualSVN server, a Subversion server that internally uses Apache, to serve my subversion repositories. I've managed to integrate WebSVN into it as well, and just now was able to get it to serve my repositories through WebSVN without having to authenticate, ie. no username or password prompt comes up. This is good. However, with this set up there is apparently no way for me to authenticate to WebSVN at all, which means all my private repositories are now invisible as far as WebSVN goes. I noticed there is a "Listen 81" directive in the .conf file, since I'm running the server on port 81 instead of 80, so I was wondering if I could set up a https:// connection to a different port, that did require authentication? The reason I need access to my private repositories is that I have linked my bug tracking system to the subversion repositories, so if I click a link in the bug tracking system, it will take me to diffs for the relevant files in WebSVN, and some products are in private repositories. Here's my Location section for WebSVN: <Location /websvn/> Options FollowSymLinks SVNListParentPath on SVNParentPath "C:/Repositories/" SVNPathAuthz on AuthName "Subversion Repository" AuthType Basic AuthBasicProvider file AuthUserFile "C:/Repositories/htpasswd" AuthzSVNAccessFile "C:/Repositories/authz" Satisfy Any Require valid-user </Location> Is there any way I can set up a separate section for a different port, say 8100, that does not have the Satisfy Any directive there, which is what enable anonymous access. Note that a different sub-directory on the server is acceptable as well, so /websvn_secure/, if I can make a location section for that and effectively serve the same content only without the Satisfy Any directive, that'd be good too.

  Read the article

• Find the IP of the router between me and main router/gateway?

  - by Crash893

  I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

  Read the article

• How to Install OS without DVD and USB boot

  - by Timothy James Reed

  I just purchased a used Dell F1D 1U rack mount server and would like to install Ubuntu or ESXi with Virtual Disks or anything for that matter. I'v read that Dell's have built in DRAC so you can access it remotely. There are 3 ethernet plugs in the back but I dont know which one to use. In the BIOS it says I can configure Remote access on [com1] or [com2] not sure if that is ethernet 1 & 2. I also set it up so to use a static IP adress. Thats as far as I have gone. Not sure what to do next. I'v Tried to do a PXE server with TFTP but get stuck at Error "cant locate file" or something like that. Not even sure I want to go that route anymore because of all the hassel of editing files. All my computers are OSX or Linux and the only Windows I have is via VMWare. What steps to i do now?

  Read the article

• There are currently no logon servers available

  - by Ian Robinson

  I am running a Windows 7 laptop that is joined to my company's domain. When I installed Windows 7, I created an account for myself, joined to the domain, and it had been working quite well even though I'm physically remote most of the time, and not actually on the network. However, today I created a new local user account (non-admin) for my little brother. While he was using it, he decided he wanted to install a program, because his account is not an admin, he was prompted to enter Administrator credentials to allow the program to make changes to his computer. I entered my credentials, and this is the first time I ran into the error message: There are currently no logon servers available to service the logon request. I tried logging off and loggin back in, rebooting, etc etc, and no matter what, every time I try to authenticate as my "normal" domain account - I get that message. I can no longer access my computer as an administrator. I no longer know how to log in to my machine using any other account aside from my little brother's non-admin account. I don't have any other local accounts created, and the default local admin account was never enabled. I'd appreciate any ideas on how I can recover access to my account. Let me know if I can provide any more information. FYI - This is a similar question but not sure any of the answers help me in my case. http://serverfault.com/questions/71632/there-are-currently-no-logon-servers-available-to-service-the-logon-request

  Read the article

• Reading log files from web application

  - by Egorinsk

  I want to write a small PHP application for monitoring logs on a Debian server, including syslog logs and Apache/PHP messages. The problem here is that Apache user (www-data) has no access to /var/log directory. What would be the best way to grant an access to logs for PHP application? Let's assume that log files can be really large, like hundreds of megabytes. I have some ideas: Write a shell script that would be run via sudo and tail last 512 Kb of log into a separate file that can be read by application - that's ineffective, because of forking a new process and having to read data twice Add www-data to adm group (that can read logs) - that's insecure Start a PHP process via cron every minute to read logs — that's not very good, because it doesn't allow real-time monitoring. Also, this script will be started even when I don't read logs, and consume CPU time (server is in the cloud, and I'll have to pay for it) Create a hardlink for all log files with lowered permissions - I guess, that won't work because logrotate could recreate log files and they'll change inode number. Start a separate nginx/Apache server under privileged user that may read logs. Maybe anyone got a better solution?

  Read the article

• Erratic WiFi 2.4 GHz channel spikes, what gives?

  - by Francis W. Usher

  Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

  Read the article

• What are these isolated resource requests in Apache's access_log?

  - by Greg

  I was looking at my Apache access log and came across some strange requests. A single IP address will access several resources (mostly css style sheets and images), but no actual pages. Sometimes they are requesting a resource that no longer exists on the server, or one that is still under the web root but no longer used (e.g. a resource in an old WordPress theme). Also: The requests list no referrer I get no useful information on the IP address by looking it up There doesn't seem to be any pattern among the IP addresses that are making these requests (e.g. different countries) Are these just links from a stale cache somewhere? Could it be a sign of an attack of some sort? Here is a typical example: GET /wp-content/themes/my-theme/images/old-image.gif HTTP/1.1" 500 809 "-" "Mozilla/4.0 (compatible;)" This was one of about 10 similar requests, some for existing resources, some for older resources. There is no other sign of this IP address in access_log. Note the internal server error, which is a topic for a different thread. What I'm asking here is where would isolated requests like this come from?

  Read the article

• Exchange 2010 OWA- Open Other User Mailbox

  - by Benjamin Jones

  I just started working for this small firm (30 people) a little bit ago, replacing their System Admin. First thing I noticed was Exchange Server 2010 was WAY out of date. Believe it or not they did not have SP1 installed. So after I installed and configured Exchange 2010 SP3 and redirected OWA I noticed something in OWA. I could add ANYONE's User Mailbox WITHOUT giving mailbox premission. I created a couple test users, same thing. I even had another employee provide me access to their OWA and they could open anyone's Inbox without granting permission. I don't want to play the blame game, but I was SHOCKED that this was going on. Luckly being such a small company I'll be able to cover this mistake that I did not create, BUT HOW? My guess is that I need to find out where the past System Admin went wrong in providing Full Access Permission? Or could this be a Auto-Mapping issue? I found this article: http://technet.microsoft.com/en-us/library/hh529943.aspx This might work $FixAutoMapping = Get-MailboxPermission sharedmailbox |where {$_.AccessRights -eq "FullAccess" -and $_.IsInherited -eq $false} $FixAutoMapping | Remove-MailboxPermission $FixAutoMapping | ForEach {Add-MailboxPermission -Identity $_.Identity -User $_.User -AccessRights:FullAccess -AutoMapping $false} However how do I insert the above code into Powershell? Again I was thrown into this mess and I'm just trying to iron out this tangled mess.

  Read the article

• Reading log files from web application

  - by Egorinsk

  Hi! I want to write a small PHP application for monitoring logs on a Debian server, including syslog logs and Apache/PHP messages. The problem here is that Apache user (www-data) has no access to /var/log directory. What would be the best way to grant an access to logs for PHP application? Let's assume that log files can be really large, like hundreds of megabytes. I have some ideas: Write a shell script that would be run via sudo and tail last 512 Kb of log into a separate file that can be read by application - that's ineffective, because of forking a new process and having to read data twice Add www-data to adm group (that can read logs) - that's insecure Start a PHP process via cron every minute to read logs — that's not very good, because it doesn't allow real-time monitoring. Also, this script will be started even when I don't read logs, and consume CPU time (server is in the cloud, and I'll have to pay for it) Create a hardlink for all log files with lowered permissions - I guess, that won't work because logrotate could recreate log files and they'll change inode number. Start a separate nginx/Apache server under privileged user that may read logs. Maybe anyone got a better solution?

  Read the article

• Using a second Wifi Router (in order to use a LAN port)

  - by Sledge81

  Problem: Connecting a TV decoder via Internet. It doesn't have inbuilt wifi so wired LAN is the only option. I bought a second Wifi Router so I could use its LAN port to create a wired internet connection to my decoder. What I want to achieve: The second Wifi Router should basically pick up the signal from the main wifi router. I would then use the LAN port to connect (with a wire) to the TV decoder. In other words have my secondary Wifi Router act as an access point, which will enable me to use a wired LAN connection to the decoder. What i've done so far: Connected the second Wifi Router to my laptop via the LAN ports. Access 192.168.1.1 and went into my second router. 1) SSID set to the same one as the main Wifi Router 2) Tried disabling DHCP and enabling DHCP (with the DNS and default gateway configured the same as the main router). When I check my network connections, I see the LAN connection too but it says 'Not connected to the internet' while the Wifi (main router) shows connected. Can someone please advise on how to use my second Wifi Router to connect to the main Wifi Router (and thus the Internet). Thanks. main wifi router: Zyxel secondary wifi router: TP Link

  Read the article

• jquery nested sortable list

  - by Y.G.J

  i have this code $(document).ready(function() { $("#test-list").sortable({ items: "> li", handle : '.handle', axis: 'y', opacity: 0.6, update : function () { var order = $('#test-list').sortable('serialize'); $("#info").load("process-sortable.asp?"+order+"&id=catid&order=orderid&table=tblCats"); } }); $("#test-sub").sortable({ containment: "ul", items: "li", handle : '.handle', axis: 'y', opacity: 0.6, update : function () { var order = $('#test-list').sortable('serialize'); $("#info").load("process-sortable.asp?"+order+"&id=catid&order=orderid&table=tblCats"); } }); }); for this kind of UL <ul id="test-list"> <li></li> <li> <ul id="test-sub"> <li></li> <li></li> <li></li> <li></li> <li></li> <li></li> </ul> </li> <li></li> <li></li> <li></li> <li></li> </ul> but it can be changed dynamiclly... when i drag and drop the main li it is working when i do it with the childs it will drag the main one what is wrong?

  Read the article

• Access variables between nested JSP tags

  - by user308053

  I would like to exchange information between two nested JSP tagx artifacts. To give an example: list.jspx <myNs:table data="${myTableData}"> <myNs:column property="firstName" label="First Name"/> <myNs:column property="lastName" label="Last Name"/> </myNs:table> Now, the table.tagx is supposed to display the data columns as defined in the nested column tags. The question is how do I get access to the values of the property and label attributes of the nested column tags from the table tag. I tried jsp:directive.variable but that seems only to work to exchange information between a jsp and a tag, but not between nested tags. Note, I would like to avoid using java backing objects for both the table and the column tags at all. I would also like to know how I can access an attribute defined by a parent tag (in this example I would like to access the contents of the data attribute in table.tagx from column.tagx). So it boils down to how can I access variables between nested JSP tags which are purely implemented through the tag definitions themselves (no Java TagHandler implementation desired)?

  Read the article

• asp.net Impersonate User for network resource access

  - by lonelycoder

  code: System.Security.Principal.WindowsImpersonationContext impersonationContext; impersonationContext = ((System.Security.Principal.WindowsIdentity)User.Identity).Impersonate(); //access network resources. impersonationContext.Undo(); web.config: <authentication mode="Windows"> </authentication> <identity impersonate="true" userName="user" password="password"></identity> As clear from web.config file, the app runs in an impersonated mode. I need to impersonate temporarily on top of that to access a network resource. I do that as shown above. This works fine on server if I browse to the website on the local IE installed on the server but when I access the app from my PC or any other PC, I get a access denied. Btw, this is all within an enterprise domain environment. so IE in both cases is passing a valid authenticated token. Any ideas what is going on. thanks.

  Read the article

• why does Integrated Windows Authentication fail when clients access off the network

  - by Bryan

  My background is not with web applications so this problem is hard for me to explain easily. First I'll try to describe the setup. Client setup:-Only browser that is effected is IE 6-8 (Firefox, chrome, opera, and safari all work fine) -A user will try to access our web application from a company laptop that is not connected to our network. -This machine will be a member of our workgroup and have the company DNS listed as a trusted intranet site. (to which the application in question would be a member) -The security logon mode is set to Automatic Logon only in intranet zone only, and IWA authentication is enabled on the clients browser.Server setup:-Windows server 2003 fp2-The application will first redirect to an Authorization asp page which has anonymous access disabled and IWA enabled in IIS.what should happen is that, since the client is not currently on the network, when this page is called it should prompt the user for network credentials. But with IE, instead of prompting, the user gets a page cannot be displayed error because the IIS manager is denying access to the asp page. If the company DNS is removed from the trusted intranet site list then it prompts correctly but disables single sign on the next time that computer is connected to the network or vpn. My assumption is that since IE uses IWA and the site is listed as an internal site, when no network is found IE just sends nulls to the server attempting to authenticate which is swiftly punted back. Other browsers do not have security zones so when network credentials are not present the server prompts for them. Is there a way to get around this so that our clients can keep the company DNS in the intranet zone but still have the server prompt for credentials when not on the network? Any attempt to allow for anonymous access on the asp page, as far as I know, will cause AUTH_USER to return null and again break SSO. I realize this is slightly rambling so I will do my best to clarify and questions you guys might have. Thanks in advance.

  Read the article

• Android: ListActivity design - changing the content of the List Adapter

  - by Rob

  Hi, I would like to write a rather simple content application which displays a list of textual items (along with a small pic). I have a standard menu in which each menu item represents a different category of textual items (news, sports, leisure etc.). Pressing a menu item will display a list of textual items of this category. Now, having a separate ListActivity for each category seems like an overkill (or does it?..) Naturally, it makes much more sense to use one ListActivity and replace the data of its adapter when each category is loaded. My concern is when "back" is pressed. The adapter is loaded with items of the current category and now I need to display list of the previous category (and enable clicking on list items too...). Since I have only one activity - I thought of backup and load mechanism in onPause() and onResume() functions as well as making some distinction whether these function are invoked as a result of a "new" event (menu item selected) or by a "back" press. This seems very cumbersome for such a trivial usage... Am I missing something here? Thanks, Rob

  Read the article

• Scrollable list items in jQuery

  - by Giles B

  Hi Guys, I have a list of 4 items and the ul has a background image that makes the second item look as though it has an arrow behind it. I want to be able to scroll the items up or down when they are clicked to the second items position so for example when I click the fourth item the whole list scrolls up so the fourth item is then postioned over the top of the background image and all the other items will be sitting in the same order above it. I have tried using jQuery Tools with the circular option selected but it clones the first an last item and i end up with a gap when i get to the bottom and I also cant make each item selectable to scroll the list up or down. Here is the code for the list <div id="priceGuide"> <ul id="priceRegion"> <li><a href="#">North & Midlands</a></li> <li><a href="#">London, north of the river</a></li> <li><a href="#">London, south of the river</a></li> <li><a href="#">South & South East</a></li> </ul><!-- /priceRegion --> </div><!-- /priceGuide --> Any help is most appreciated. Thanks Giles

  Read the article

• Using a profile property of type List in .NET Membership

  - by hancock

  Hi, I'm working on a C# Webservice that needs to provide authentication as well as roles and profile management. I need each profile to have a property of type List. The profile section in the web.config looks like this: <profile defaultProvider="MyProfileProvider" enabled="true"> <providers> <remove name="MyProfileProvider"/> <add connectionStringName="MySqlServer" applicationName="MyApp" name="MyProfileProvider" type="System.Web.Profile.SqlProfileProvider" /> </providers> <properties> <add name="Websites" type="System.Collections.Generic.List&lt;String&gt;" serializeAs="Binary"/> </properties> </profile> However, when I start the webservice and try to access that property it returns the following error: System.Configuration.ConfigurationErrorsException: Attempting to load this property's type resulted in the following error: Could not load type 'System.Collections.Generic.List<String>'. (C:\Projects\MyProject\web.config line 58) --- System.Web.HttpException: Could not load type 'System.Collections.Generic.List<String>'. Is there a way to use a generic collection for this purpose?

  Read the article

• MySQL Access denied error

  - by dancingbush

  I am trying to install mySQL on a Mac OS 10.8 and set up a user account. NOTE I am a abs beginner when it comes to using the command line in Terminal window. I used these instructions to install: http://www.macminivault.com/mysql-mountain-lion/ I set my own password for all users here: GRANT ALL ON *.* TO 'root'@'localhost' IDENTIFIED BY 'mypass' WITH GRANT OPTION; quit Every time i try to execute mySQL as a root user on the command line i get this: Ciarans-MacBook-Pro:~ callanmooneys$ mysql -u root ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: NO) I read around on the net and tried various things including tried this to change password: mysqladmin -u root -pyourcurrentmysqlrootpassword password yournewmysqlrootpassword, it returns -> -> USE mysql -> If i simply type 'mysql' and launch the mySQL monitor then try to crete a user account: mysql> USE mysql ERROR 1044 (42000): Access denied for user ''@'localhost' to database 'mysql' mysql> Also tried answers on forum: access is denied for user 'root'@localhost mysql error 1045 returned '[email protected] command not found And MySQL - ERROR 1045 - Access denied: Ciarans-MacBook-Pro:~ callanmooneys$ mysqld_safe --skip-grant-tables 131105 21:44:41 mysqld_safe Logging to '/usr/local/mysql/data/Ciarans-MacBook-Pro.local.err'. 131105 21:44:41 mysqld_safe Starting mysqld daemon with databases from /usr/local/mysql/data /usr/local/mysql/bin/mysqld_safe: line 129: /usr/local/mysql/data/Ciarans-MacBook-Pro.local.err: Permission denied /usr/local/mysql/bin/mysqld_safe: line 166: /usr/local/mysql/data/Ciarans-MacBook-Pro.local.err: Permission denied 131105 21:44:41 mysqld_safe mysqld from pid file /usr/local/mysql/data/Ciarans-MacBook-Pro.local.pid ended /usr/local/mysql/bin/mysqld_safe: line 129: /usr/local/mysql/data/Ciarans-MacBook-Pro.local.err: Permission denied Ciarans-MacBook-Pro:~ callanmooneys$ mysql -u root ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/tmp/mysql.sock' (2) Ciarans-MacBook-Pro:~ callanmooneys$ Feedback appreciated.

  Read the article

• python-xmpp and looping through list of recipients to receive and IM message

  - by David

  I can't figure out the problem and want some input as to whether my Python code is incorrect, or if this is an issue or design limitation of Python XMPP library. I'm new to Python by the way. Here's snippets of code in question below. What I'd like to do is read in a text file of IM recipients, one recipient per line, in XMPP/Jabber ID format. This is read into a Python list variable. I then instantiate an XMPP client session and loop through the list of recipients and send a message to each recipient. Then sleep some time and repeat test. This is for load testing the IM client of recipients as well as IM server. There is code to alternately handle case of taking only one recipient from command line input instead of from file. What ends up happening is that Python does iterate/loop through the list but only last recipient in list receives message. Switch order of recipients to verify. Kind of looks like Python XMPP library is not sending it out right, or I'm missing a step with the library calls, because the debug print statements during runtime indicate the looping works correctly. recipient = "" delay = 60 useFile = False recList = [] ... elif (sys.argv[i] == '-t'): recipient = sys.argv[i+1] useFile = False elif (sys.argv[i] == '-tf'): fil = open(sys.argv[i+1], 'r') recList = fil.readlines() fil.close() useFile = True ... # disable debug msgs cnx = xmpp.Client(svr,debug=[]) cnx.connect(server=(svr,5223)) cnx.auth(user,pwd,'imbot') cnx.sendInitPresence() while (True): if useFile: for listUser in recList: cnx.send(xmpp.Message(listUser,msg+str(msgCounter))) print "sending to "+listUser+" msg = "+msg+str(msgCounter) else: cnx.send(xmpp.Message(recipient,msg+str(msgCounter))) msgCounter += 1 time.sleep(delay)

  Read the article

< Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >