Search Results

Search found 19908 results on 797 pages for 'bit ly'.

Page 178/797 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• Can I clone my hard drive to an external and boot from the clone?

  - by willbuntu

  First thing: I am not asking what software I'm supposed to use. I already know the answer: Ghost (proprietary), Clonezilla, and dd (if I'm careful). What I really want to know is if it is possible to (essentially) bit-for-bit clone my entire installation (OS, installed software, activation(s), etc.) to an external USB hard-drive, and then boot off of that (if I need to, I know how to edit BIOS settings and use Plop boot manager), and work with it day-to-day as if there was virtually no difference from using my internal HDD now. Again, I'm not asking how to install Windows to an external (because I know I'd need to do some special workaround), I'm asking if I can clone everything and boot off of it. In case you're wondering why I'm going to this trouble: I'm using a Lenovo Essentials laptop that has an unmodifiable partition table (due to recovery crap), and has all 4 of its partitions spoken for (3 primary, one extended, cannot change the extended). Anyway, my thought is that if I can clone everything and boot off of it when I need to, and just have a Linux distro on the internal HDD, then that could work.

  Read the article

• Developer hardware autonomy in a managed desktop environment [closed]

  - by Troy Hunt

  I’m looking for some feedback on how developer PCs are managed within environments that have a strict managed desktop policy (normally large corporations). For example, many corporate environments control the installation of software and the deployment of patches and virus updates through a centralised channel. This usually means also dictating the OS version and architecture (32 bit versus 64 bit) which will likely also mean standardised hardware configurations. I’m particularly interested in feedback from developers who work in this sort of environment but have a high degree of autonomy over their machines. This might mean choosing your own hardware vendor, OS type and version and perhaps how the machines are built and maintained. I have several specific questions: How do you satisfy the needs of security, governance etc whilst maintaining your autonomy? For example, how do you address concerns about keeping virus definitions and OS patches up to date? Do you have a process for gaining exemption from standard desktop builds and if so, what do you need to demonstrate in order to get this? How have you justified this need to the decision makers? Essentially, what is the benefit to your role as a developer by having this degree of autonomy? Thanks very much everyone. Update: There's a great post from Jean-Paul Boodhoo which addresses the developer tool component of the quesiton here: http://blog.jpboodhoo.com/TheFallacyOfTheStandardizedDeveloperMachineimage.aspx

  Read the article

• named responding recursive on norecurse queries

  - by Keks

  I have a server on which named is running. It is intercepted with another named server which it is not aware of. Querying the first named server results in timeouts. The server tries to resolve the query recursively. During that the firewall redirects the DNS Request from the first named server to the second one (the query from the first one is addressed to a e.g. a root server and has its "Recursion desired" bit set to 0). Despite that the second named responds to this request with a entirely or at least 1 level more resolved response than the first named server expects. So it ends up with a timeout even though it got a correct name server or even the full IP for the queried domain. In the first case the first name server tries to follow the authority domain ignoring the coresponding glue record and ends up in a loop it aborts: queried: google.com -> got from named#2: ns1.google.com -> ignore glue record and query: ns1.google.com -> got authority from named#2: google.com In the second case it ignores the answer section with the correct IP and instead tries to follow the name servers from the authority section, which ends up in the same dead end as case 1. So how can it be that the second named responds with recursive results even though the bit was explicitly set to 0 in the request from the first named?

  Read the article

• How to distribute multiple executions of an app across many machines

  - by Salec

  I've got a simulation app (64-bit windows) that runs without any user interaction. This app gathers information and pushes it to a remote MS SQL Server. What I'd like to do is execute this simulation as many times as I can on multiple machines after our nightly build has finished and it has passed the test suite. If possible I'd love to have the ability to configure it to stop after x total runs or if the entire batch has taken over y hours. I've tried using Visual Studio's built in test framework since we already have a test lab set up with multiple agents. I created a single unit test that simply runs the simulation then I created an ordered test and added that single test multiple times (from what I gather, this is the only way to execute the same unit test more than once). I found that ordered tests are only run on a single agent and not distributed which is very limiting. We use TeamCity to perform our nightly builds and I suspect it's possible to implement this on top of that, but I'm fairly new to TeamCity. We also have Jenkins and Bamboo available and I'm open to any other software that would get the job done presuming it runs on a 64-bit Windows OS. Any suggestions?

  Read the article

• Get Matrox Millenium video card working in Ubuntu 9.10

  - by wcoenen

  I have installed Ubuntu 9.10 on an old PC and it is mostly working, except for some heavy drawing defects that show up whenever I start dragging a window or scrolling inside a window or menu. It looks like the video driver copies the rectangle being moved to the wrong location. I have taken a look in /var/log/Xorg.0.log and the following line shows the detected video card: (--) PCI:*(0:0:8:0) 102b:0519:0000:0000 Matrox Graphics, Inc. MGA 2064W [Millennium] rev 1, Mem@ 0xf9800000/16384, 0xfb000000/8388608, BIOS @0x????????/65536 (==) Using default built-in configuration (30 lines) (==) --- Start of built-in configuration --- Section "Device" Identifier "Builtin Default mga Device 0" Driver "mga" EndSection How do I fix the drawing defects? It turned out that the 24 bit color depth (automatically selected by ubuntu 9.10) was the problem; apparantly the mga driver doesn't handle this well for cards with little memory. I took the following steps to resolve the issue (you can skip the first three steps if you already have a semi-working xorg.conf file): Reboot ubuntu in recovery mode, to get a root console without X running. Run Xorg -configure to generate a xorg.conf.new file Copy the file to /etc/X11/xorg.conf with cp xorg.conf.new /etc/X11/xorg.conf (assuming it didn't exist yet; that's why I generated it) Open the new config file with sudo nano /etc/X11/xorg.conf and make sure the screen section is configured for 16 bit color depth like this: Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection EndSection I can't guarantee those were the only important changes I made - I tried a few things in my attempts to create a valid xorg.conf file. But I'm pretty sure that the screen section was the important part.

  Read the article

• Can't detect hard drive on Macbook Pro

  - by MartinMoizard

  I changed a few month ago the config of my Macbook Pro with the following: I bought a SSD hard drive I removed the hard drive of my Mac book Pro and installed there my brand new SSD Then I removed my DVD drive and installed my hold hard drive instead with a caddy Everything was working great until today when I couldn't access anymore to my old hard drive because it is not detected anymore. Sometimes Mac OSX is mounting it but it takes like 15 min to browse a simple folder. I opened my laptop to have a look at the problem. It seemed like the optical drive connector was not plugged correctly to the motherboard (that connector: http://cl.ly/2T0X2e1j0J1g47061d1t). So I plugged it correctly and reboot. It didn't fix my problem. Then I tried to put my SSD in the caddy and to boot: no hard drive was detected. So I guess there is something wrong either with the caddy, either with the optical drive connector, or either with the plug that is on the motherboard. So my question is, how can I know where the problem comes from?

  Read the article

• USB-to-Serial showing gibberish at 115200 Baud

  - by Mose

  I've got a serious problem which drives me crazy because I tried everything I could think of. First of all, I made a video: http://youtu.be/boghkuq7L_s but please read the following text for more information, not only view the video! When using a USB-to-Serial interface everything works as long as I don't go beyond 57600 Baud. At higher rates I only get giberish like this: év.­b0JNLYÆÿ¿iëd0U²(kßÞb! ú]/xscB!ï¯!BoXûÿ1ïâÖCÿ6ÌAnè*íÌC)º¿BíÞØ.C.@ÆÃwHJÂs "YE:ñ.èFðÌCÊ÷ÞÄ !x H w6@BtbHJ ̪ Ì6ì H¾a¿bH.">îvy®;f<ßBÌ p­L¨fæH­E ­þ¼MBÞI What makes the problem so strange is, I exchanged every component and the problem still presists. I tried differtent OSes (Ubuntu, WinXP, Win7, OSX 10.7) with 32 and 64 Bit. I tried USB-to-Serial interface from FTDI and Prolific. I tried reading the output from my Raspberry PI and from an Asterisk Appliance. I changed the cables and the wiring. Nothing helped. In the video I made a example with a old Notebook with native COM and put the USB-to-Serial to the same connection as "sniffer" (only Rx and GND connected) to make sure the output and everything is ok as one can see on the native port. The voltage is ok. Settings for both are 115200 Baud, 8 Bit with 1 Stop and no flow control. Native is ok. USB is messed up. I used the newest drivers and double checked all connections. I have no idea what is wrong here. As I couldn't find anyone describing problems like this I question my long experiance in computer science and think I'm doing some completly wrong... Please help :-/

  Read the article

• VLC Crash when playing MKV files in Windows 7

  - by Phelios

  I'm not sure if the mkv file is corrupted, but when it is opened with VLC player, VLC loads up and displays nothing. Can't even close VLC after that. And also, VLC is running with 50% of the CPU. I have to use End Process to kill it. How do I know if the file is corrupted? How do I solve this? info from mediainfo Format : Matroska File size : 69.4 MiB Duration : 21mn 48s Overall bit rate : 445 Kbps Encoded date : UTC 2009-11-20 18:33:49 Writing application : mkvmerge v2.9.7 ('Tenderness') built on Jul 1 2009 18:43:35 Writing library : libebml v0.7.7 + libmatroska v0.8.1 Video ID : 1 Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Format settings, CABAC : Yes Format settings, ReFrames : 2 frames Format settings, GOP : N=1 Codec ID : V_MPEG4/ISO/AVC Duration : 21mn 48s Width : 640 pixels Height : 352 pixels Display aspect ratio : 16:9 Frame rate : 23.976 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Audio ID : 2 Format : AAC Format/Info : Advanced Audio Codec Format profile : HE-AAC / LC Codec ID : A_AAC Duration : 21mn 48s Channel(s) : 2 channels Channel positions : Front: L R Sampling rate : 48.0 KHz / 24.0 KHz Compression mode : Lossy

  Read the article

• empty file from tomcat https redirect?

  - by amertune

  I am using tomcat 6.0.20, with jdk 1.6.0_18 on 64 bit linux (tomcat downloaded from tomcat.apache.org, not installed from repositories). I have iptables redirects from port 80 - 8080 and 443 - 8443. In server.xml, the connector for port 8080 redirects to 443, and the 8443 connector has proxyPort="443". In conf/web.xml, I have added this bit at the end of the file (but still inside the <web-app</webapp tags). <security-constraint> <web-resource-collection> <web-resource-name>Protected Context</web-resource-name> <url-pattern>/*</url-pattern> </web-resource-collection> <user-data-constraint> <transport-guarantee>CONFIDENTIAL</transport-guarantee> </user-data-constraint> </security-constraint> I also have two contexts, ROOT and mywebapp. If I go to http://myurl.com, then I get redirected to https://myurl.com. If I go to http://myurl.com/mywebapp/, then I get redirected to https://myurl.com/mywebapp/. The problem I'm having is when I go to http://myurl.com/mywebapp (no trailing slash). When I do this I get a prompt to download an empty file that has an empty name. Going to https://myurl.com/mywebapp works. I would think that a user typing myurl.com/mywebapp is far from rare. Is there something I'm missing?

  Read the article

• Will a SQL Server client alias survive a sysprep?

  - by shufler

  I want to sysprep a Windows Server 2008 R2 SP1 machine that has SQL Server 2008 R2 SP1 installed (for reference, SQL Server 2008 R2 has a new sysprep feature that allows the instance to be sysprepped). On the server is a SQL Server client alias that points to the default SQL Server database engine instance. For reference, the alias is called Alias-SQLServer and has been configured in both 32-bit and 64-bit cliconfig versions (that is, both registry keys exist) The alias points to the local instance as the image will be used to create development VMs and the installation script for the application that is being developed will use the SQL Server client alias in order to generalize the installation scripts. I can't seem to find information about whether the sysprep tool will update the SQL Server client alias's registry keys with the server's new name once it's unsealed. My guess is that it is not; how is sysprep to know that the server name the alias points to will be different for each image? Right? Perhaps if the alias points to localhost instead of the server name this will work?

  Read the article

• VM load and ping problems after replacing server motherboard

  - by Andre

  Recently, we had to replace the motherboard of one of our servers. The procedure was done by IBM as it had guarantee. The server runs ESXi 5.1, with several virtual machines, including our main mail server (Domino) and a file server. After the replacing the motherboard and staring the VMs, ESXi asked us if we had moved it or copied (different motherboard is like a different computer). We clicked the latter. We started each machine and after some basic reconfiguration, all of them were up. However, we have been having problems with the mail server, it has been acting really slow at times (this could be when it syncs with the secondary mail server) and we have been checking with Centreon (a Nagios frontend) that its CPU load has been a bit high at times and ping response too. There was a moment this morning in which I tried connecting via SSH console and it was really slow to show login and basic commands like ifconfig and top. This particular mail server is a CentOS 4.4.7 64-bit. The little configuring we had to do after restarting it was to configure the network connection as it was resolving through DHCP. Our mail software is Lotus Notes server 9. Do you know of any way in which this replacement may be causing these difficulties, and how to fix it? Thanks.

  Read the article

• Migrating ODBC information through a batch file

  - by DeskSide

  I am a desktop support technician currently working on a large scale migration project across multiple sites. I am looking at a way to transfer ODBC entries from Windows XP to Windows 7. If anyone knows of a program or anything prebuilt that already does this, please redirect me. I've already looked but haven't found anything, so I'm trying to build my own. I know enough basic programming to read the work of others and monkey around with something that already exists, but not much else. I have come across a custom batch file written at one site that (among other things) exports ODBC information from the old computer and stores it on a server (labelled as y: through net use at the beginning of the file), then later transfers it from the server to a new computer. The pre-existing code is for Windows XP to XP migrations. Here are the pertinate bits of code: echo Exporting ODBC Information start /wait regedit.exe /e "y:\%username%\odbc.reg" HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI (and later on) echo Importing ODBC start /wait regedit /s "y:\%username%\odbc.reg" We are now migrating from Windows XP to 7, and this part of the batch file still seems to work for this particular site, where Oracle 8i and 10g are used. I'm looking to use my cut down version of this code at multiple sites, and I'm wondering if the same lines of code will still work for anything other than Oracle. Also, my research on this issue has shown that there are different locations in 64 bit operating systems for 32/64 bit entries, and I'm wondering what effect that would have on the code. Could I copy the same data to both parts of the registry, in hopes of catching everything? Any assistance would be appreciated. Thank you for your time.

  Read the article

• Screen randomly goes blue/black/white

  - by FubsyGamer

  Problem Randomly, while using my computer, the monitor goes dark grey/almost black, or it goes white with faint grey vertical lines, or it goes blue with black vertical lines. It's as if the computer powers off. People tell me I sign out of Skype, Spotify stops playing when it happens, etc. When I look at the tower, it doesn't seem like it's off at all. Nothing changes, fans are spinning, lights are on, etc. If you were only looking at the tower, you'd never know there was a problem The only way I can get it to come back up is to push and hold the power button and turn it off, then back on This never happens while I'm playing video games. I've done 5-6 hour sessions of League of Legends, and it doesn't do anything When I'm just browsing the web, reading email, checking Reddit, etc, it happens all the time. It can happen multiple times in a session, it usually takes only about 5 minutes from the time I start browsing to when the computer crashes This started happening after I moved to a new apartment (this has to be relevant somehow, it was not happening where I lived before) There is nothing in the crash logs or event logs System Specs i5 2500k CPU AMD Radeon 6800 GPU Gigabyte z68a-d3h-b3 motherboard WD VelociRaptor 1 TB HDD Screenshots Device manager About screen Things I have tried I was getting a WMI Error in my event logs, but I fixed it using Microsoft's fix, KB 2545227 I was using Windows 8. I wiped the HDD and downgraded to Windows 7 64 bit I took out the video card and used a can of air to totally clean out the video card, all fans, and the inside of the computer in general. I made sure all of the video card pins were fine, then reconnected it I tried to update my motherboard BIOS, but anything I downloaded from Gigabyte was only for 32 bit machines, not 64. I don't even know how to tell what my motherboard BIOS is at right now I am using a power strip, and anything else connected to it works just fine If I re-seat the monitor cable while this is happening, nothing changes Please, help me. I've been battling this for several weeks now, and it's so frustrating it makes me not even want to use the computer.

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• linux networking: how to redirect incoming connections from old server to new server?

  - by aliz

  hi I'm in the process of moving my old server to a new server, but i will keep the old server running for database replication and load balancing, etc. each server has a separate internet connection with a static ip, and they are connected through a local Ethernet connection. I've got Ubuntu 8.04 32-bit running on old server and Debian 6.0 64-bit on new one. shorewall firewall is installed on both servers. there are some outdoor devices which are periodically sending data to port 43597 for old server IP address. I can run multiple instances of the network service which is responsible for receiving data from devices on a server but on different ports. here's the question: how can I run the service on new server and have connections coming to old server redirected to it, and new devices can still connect to new server's IP address preferably on the same port and same service? until all devices get updated to send to new server. I've tried a shorewall DNAT rule, but seems like new server's default route should be changed to ethernet connection, which breaks other things. I also found about redir utility, but still haven't tried it. is there any best practice or simple solution for such a scenario, i'm not aware of? thanks in advance.

  Read the article

• Updating ASUS BIOS on Windows 7 64bit

  - by joesavage

  I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

  Read the article

• Why is my new PC so slow at startup?

  - by rumtscho

  Bought a new PC this weekend, and it works really good. Only I have one big problem: startup time. Its BIOS needs 62 sec to load, then from Grub start to pw entering screen it's another 26 sec. I think this is a lot, because my old PC needs 34 sec for BIOS and another 8 sec to pw screen. After I enter the pw, the desktop is usable with practically no delay on both. The new PC is a core i7-930, running a Lucid Lynx 64 bit from a Intel Postville SSD (no internal HDs). The old PC is a Pentium 4 celeron (forgot the clock speed) running a Lucid Lynx 32 bit from an ATA 100 hard drive. Neither PC is overclocked. The new one has boot sequence 1.DVD ROM, 2.SSD (connected over SATA in AHCI mode), 3. removable drive. The old one boots from 1. DVD ROM, 2. HDD, 3. Floppy. Neither has a second OS installed. The new one has less software installed than the old one (I think), but the boot time difference was noticeable even before I made any installs. As far as I know, just the SSD should be enough to make a noticeable difference in boot time. I thought that having a good mainboard on the new PC as opposed to the basic office model on the old one would also mean a faster loading BIOS. If these assumptions are right, I guess I must have misconfigured something in the BIOS of the new PC. How should I configure it for a fast boot? It has an ASUS P6X58D board with an AMI BIOS, if you need the BIOS revision number I could post that too.

  Read the article

• Windows 8 install from USB freezes

  - by Rafael Almeida

  I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

  Read the article

• 2 routers at home- how to connect with VNC?

  - by Charles Leviton

  I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

  Read the article

• Why just splitting an Ethernet cable does not work?

  - by Sin Jeong-hun

  I thought the Ethernet is logically one-line communication bus (for argument's sake, I am excluding hubs). All machines attached in the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why splitting one Ethernet line from my home router into two and connecting two computers would not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room and I had put a computer in another room (also my room, though). Since wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

  Read the article

• windows 2008 r2 iis worker proccess memory usage increase

  - by nLL

  I have this web site written in c#. around 400-500 users online at any time. it was on windows 2008 32 bit machine before and never ever locked/slowed down due to increased memory consumption up until i upgraded it's server to win 2008 r2 64 bit. Old server had only 4 gig ram and quad core cpu at 2ghz. site was working just fine. since i've upgraded the server i noticed (2 times with in 10 days) it started to eat ram. last night it went up to 4 gb ram. with ram increase response slows down quite a lot. recycling app pool doesn't help. I have to restart it's worker process to recover. i've noticed this usually happens if there are continuous errors. as i didn't change anything in the code am i safe to assume it is not related to memory leak in the code? did anyone came across something like that? same thing happens if i create continuous errors with classic asp. thanks

  Read the article

• File corruption (bad checksums) in large files copied to VMware guest

  - by AllanA

  In setting up a development lab, I've got a desktop system running ESXi 4.1.0 (free license) on SATA RAID 0 (already purchased and configured when I started this job; I'm open to hardware input as it pertains to my problem.) Its guests so far include two Win2008 Server R2 64-bit VMs and on Ubuntu 10.04 64-bit VM. I'm installing onto the Windows servers. We've been copying off some fairly large files (over a gigabyte) for an installation, hoping to install more quickly from a (virtual) hard drive than from the network for from BD-ROM. The problem is that they keep coming up with different checksums from the originals. The file sizes are the same, but md5sum reports different numbers (and so does the installer, as it refuses to continue when the checksums don't match.) I've tried copying directly from the BD-ROM (attaching the OS drive to the host system's physical drive). I've tried copying the large files onto a co-worker's Windows machine from his Blu-Ray drive; when I do that, the checksums match. But when I copy from his machine to the VM guest over a network share, the checksums no longer match. Thinking this meant a corrupt destination drive, I deleted it in vSphere and added another freshly created drive. The problem persists. I'm not sure what to try next.

  Read the article

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• Are there any benchmarks showing difference between hardware virtualisation enabled/disabled?

  - by Wil

  I have a 13" sub-laptop/large-netbook, it has an AMD Athlon Neo X2 L335, and I chose this one because it supports hardware virtualisation. In the end, I hardly do any virtualisation on it, however, when I do... it is fast. To my shock, I went in to the BIOS and saw that virtualisation was disabled! I turned this on and, I see no speed difference.... or at least none that I can tell. I do not have time to do a full set of benchmarks - and I run quite a bit of software on the host, so it wouldn't be scientific. I have searched quite a few places and I just can not find any benchmarks showing the difference of virtualisation bit enabled/disabled on the same hardware. Does anyone have any benchmarks they have seen that they can share? In addition, I know there was an uproar a while ago as Sony disable the hardware virtualisation on some models and only offer it in their higher models as a premium feature, however, apart from forcing an up-sell, are there any benefits to having it disabled e.g. battery/heat? I just can't find any information and can't work out why it would be disabled by default. Edit--- To add, The only thing I can find is that without it, you can not perform x64 virtualisation as fast. This is the only down side I can find. However, if this is the only difference, then I am still interested in the second part of the question - why offer the option to disable it?

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >