Search Results

Search found 46013 results on 1841 pages for 'super chicken'.

Page 178/1841 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• iptables openvpn forward selectively from eth to tun

  - by Bryan Hunt

  Simple for those who know, indecipherable for those who don't... I'm running openVPN on (hypothetical) 66.66.66.66, I want to FORWARD incoming traffic, arriving on interface eth0 to interface tun0. It would also be nice to filter - based on destination IP address. I'm doing the NAT later on, but like to lock down early wherever possible. So onto the main course... This works: #Enable forwarding from eth0 to tun0 iptables -A FORWARD -i eth0 -o tun+ -j ACCEPT But this doesn't pass any packets whatsoever: #Stricter version iptables -A FORWARD -i eth0 -o tun+ --dst 66.66.66.66 -j ACCEPT Am I being unacceptably foolish?

  Read the article

• How do you sync tabs between computers with Mozilla Firefox Sync?

  - by 1.21 gigawatts

  Mozilla says that with Firefox Sync if you are working on one computer with 5 tabs open you can then switch to another computer or device and Sync can or will update the second computer with those tabs. How do I do this? BACKGROUND I have setup Firefox Sync on both devices and they have been synced. How do you sync them again? Is it automatically syncing them in the background? How often? How do you sync the tabs? Are the passwords synced? Documentation The documentation below describes how to add another device or computer to Sync. It says that when you add the device it syncs it. But it doesn't describe how and when it keeps it in sync or how to sync the tabs. [1] http://support.mozilla.org/en-US/kb/what-firefox-sync

  Read the article

• pfSense 2.1 OpenVPN client not using tunnelled interface

  - by Brian M. Hunt

  I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

  Read the article

• Cursor lag when mouse cursor changes?

  - by Mathias Lykkegaard Lorenzen

  Cursor lag issue Introduction I'm experiencing a newly arrived problem lately that frustrates me a lot. The computer I bought is a Clevo 150ERM. Two of my friends bought the same machine, and are experiencing the same issue. The computer came with Windows 7. There, I had no issues. Then, when we all switched to Windows 8, they had the mouse problem and I didn't. That is until after 4 or 5 months when I decided to install the RTM driver of my Intel graphics chip, and the latest Nvidia driver. I also installed the latest version of Skype that just released (Skype 6 and Skype for Metro). This basically leads me to conclude that the issue is not hardware-prone, and is not based on the operating system itself, rather the drivers or components that follow with it. Description of the issue The issue itself (lag with the mouse) happens whenever the cursor icon changes. For instance, if I keep hovering from and to a textfield (and the cursor changes into a caret and then back to a mouse), it stops for 200 milliseconds while it changes the icon. An example is if I follow the mouse in the pattern shown by the arrows below. When crossing the window border, the cursor changes into a "resize window" cursor for a short while, making the cursor lag. This doesn't sound like much, but it happens every time the cursor changes (even if it's to just move the mouse somewhere else, and accidentally make it cross a window border from where the resize cursor shows etc). What do you suggest I try?

  Read the article

• How to run Windows 7 Explorer shell with Administrator Privileges by default

  - by Barry Kelly

  The Windows 7 shell (Explorer) can be made to run with Administrator privileges by this manual process: Kill Explorer shell by holding down Shift+Ctrl, right-clicking the Shut down button in the Start Menu, and selecting Exit Explorer Start Task Manager with Ctrl+Shift+Esc Elevate Task Manager privileges by going to Processes tab and selecting Show processes from all users Then start up a new instance of the shell by File | Run in Task Manager, typing in explorer, and selecting the Create this task with administrative privileges. After following the above process, the Windows shell will be running with administrative privileges, and any programs it launches will also have administrative privileges. This makes performing tasks that require the privilege far easier, particularly for command-line applications, which usually fail silently or with an Access denied. message rather than giving an opportunity to use UAC to elevate the process's privileges. What I'm interested in, though, is creating an account which uses a privileged shell by default, rather than having to follow this laborious process every time. How can it be done?

  Read the article

• Play audio over network with Windows 7?

  - by Josh

  I have a unique situation where I'd like to stream audio (ALL audio, not just mp3s, etc) from my laptop to another computer over the network. I live in a studio apartment and my laptop is my main computer but I'd like it's audio to play on my htpc with a nice stereo system. Since it's a studio, both computers are in the same room so I don't want 2 sets of speakers. I want my computer to directly play back through the stereo. I used to do this with pulseaudio but my job now requires that I run Windows full time. I'm aware of Shoutcast and other similar streaming solutions but I don't want any transcoding done. It's a waste of CPU and not to mention my laptop fans, and I don't mind the network bandwidth that uncompressed audio requires. Is there a way to run Shoutcast without encoding? Also, I know that Windows Remote Desktop can play audio over the network pretty easily. Is this part of .Net that I could just code a simple app that streams the audio without RD'ing in? I also don't want to run it over a physical wire. :)

  Read the article

• How to protect comments in Microsoft Word

  - by TestSubject528491

  I have inserted personal comments into a Word document, which I am distributing to other authors. How do I send them the file without them being able to see my comments? I can "hide" comments by going to the Review ribbon and deselecting Comments under Show Markup, but then when I close and reopen the file, the comment reappears. The same thing happens when I choose Final instead of Final Showing Markup. Is there a way to make comments only visible to the author by whom they were written?

  Read the article

• WD My Passport Essential SmartWare External Hard Drive

  - by Acer

  Hi Ive been gifted a My Passport SmartWare External Hard Drive(500gb). I used it and it works fine and installed WDSmartWare The Second time i used it,still fine,but I took it out without using the "Safely Remove Hardware" So the third time I used it,there's a bubble come out that says: USB Device Not Recognized One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it.For assistance in solving the problem, click this message. I tried connecting it to other USB Ports but it didn't work I tried Uninstalling WDSmarWare and connect it but it didn't work Please help me I like this hard drive so much and I spoilt it easily XD P.S I think about 13% has been used up in the Hard Drive P.S.S Other USBs can work fine in the computer P.S.S.S I tried connecting it to other computer and works fine OMG

  Read the article

• Are these computer parts compatible?

  - by Jcubed

  so I'm building a computer and i want to know if all these parts are compatible. case: http://www.amazon.com/Xion-Gaming-Steel-Tower-Computer/dp/B002139YSS/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270923001&sr=8-1 power supply: http://www.amazon.com/Thermaltake-W0121RU-PurePower-Version-PCI-Express/dp/B0015MCMRG/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924656&sr=1-1 motherboard: http://www.amazon.com/GIGABYTE-GA-EP45-UD3P-LGA-Intel-Motherboard/dp/tech-data/B001HH2WE2/ref=de_a_smtd processor: http://www.amazon.com/Intel-Processor-1333MHz-LGA775-BX80570E8400/dp/B00116SLYY/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924524&sr=1-1 hard drive: http://www.amazon.com/Western-Digital-Caviar-Black-WD1001FALS/dp/B001C271MA/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924586&sr=8-1 DVD/Blu Ray Dive: http://www.amazon.com/LITE-Blu-ray-Internal-Optical-iHOS104/dp/tech-data/B002EE996Q/ref=de_a_smtd Graphics Card: http://www.amazon.com/Sapphire-Radeon-100252HDMI-PCI-Express-Graphics/dp/B001SJLLTQ/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924798&sr=1-1-spell Sound Card: http://www.amazon.com/Creative-Labs-SB0570L4-Blaster-Audigy/dp/B000LP0R3E/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924850&sr=1-1 Memory: http://www.amazon.com/Corsair-TWIN2X4096-8500C5DF-Dominator-PC2-8500-1066MHz/dp/B0014Z0Q04/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924896&sr=1-1-spell OS: Ubuntu 64-bit

  Read the article

• Synchronize pasteboard between remote tmux session and local Mac OS pasteboard

  - by bhargav

  Setup: I use iTerm2 on MacOS to connect to a remote server. The remote server runs tmux, in which I open files and edit in vim sessions. Problem: I can't copy/paste between the remote tmux session and the local iTerm client. I can use iTerm 2's alt/option + mouse selection to select text, but this copies over multiple vim panes/tmux panes - bad. Is there any elegant solution to make selections in tmux panes synchronize between the remote pasteboard and the local (MacOS pasteboard)? I've seen reattach-to-user-namespace, but I'm pretty certain it doesn't do what I want.

  Read the article

• Why Does Wireless Gear Degrade Over Time?

  - by bahamat

  I saw this originally posted on slashdot, but their comment format is not conducive to actually getting a correct answer. Having directly experienced this phenomenon myself, I'm now asking here where I think I can actually get an educated answer. Here's the original question verbatim: Lately I have replaced several home wireless routers because the signal strength has been found to be degraded. These devices, when new (2+ years ago) would cover an entire house. Over the years, the strength seems to decrease to a point where it might only cover one or two rooms. Of the three that I have replaced for friends, I have not found a common brand, age, etc. It just seems that after time, the signal strength decreases. I know that routers are cheap and easy to replace but I'm curious what actually causes this. I would have assumed that the components would either work or not work; we would either have a full signal or have no signal. I am not an electrical engineer and I can't find the answer online so I'm reaching out to you. Can someone explain how a transmitter can slowly go bad? Common (incorrect, but repeated) answers from slashdot include: Back then your neighbors didn't have wifi, now they do. They drowning you out. I don't think this is likely because replacing the access point with a new one and using the same frequencies solves the problem. Older devices had low transmit power. Crank that baby. As mentioned by a FreeBSD wireless developer this violates regulations and can physically damage the equipment. It was also mentioned that higher power in one direction is not necessarily reciprocated. This shows higher bars, but not necessarily a better connection. Manufacturers make cheap crap designed to wear out. This one actually may be legitimate although it is overly broad. What specifically causes damage over time? Heat? Excessive power? So can anyone provide an informed answer on this? Is there any way to fix these older access points?

  Read the article

• Disable Windows Media Player "media server" network locations

  - by Moses

  I'm running Windows 8 and in the Computer menu, I see a huge list of "media server" network locations of many of the PCs in my network (most running Windows 7). Is there a way to either locally disable this so I don't see this list every time, or disable this sharing feature on the other computers? I've tried disabling "Media Streaming options" from the Network and Sharing Center (on my PC), but that had no effect. Another thing I tried was enabling Media Streaming, but then selecting all the found clients and clicking Blocked in the list of found clients. That had no effect in removing the list either. I've also attempted disabling the Windows Media Player Network Sharing Service, but alas, the list remains. I'm starting to believe there's a magic registry key to unbury and flip to a "1", but all the searching I've done has come up empty.

  Read the article

• Acer Aspire ASE700-UQ660A will not respond to power button

  - by Tim R.

  This is something of a continuation of this question. I am now completely unable to boot this computer. The last time I used it, I used hibernation mode. When I needed to use it again, it would not respond at all to the power button, keyboard, or mouse. I tried: Holding down the power button for 15 seconds pressing the power button Unplugging the power cord for 30 seconds, plugging it back in, and trying again Removing the motherboard battery for over a minute and reinstalling it Before removing the motherboard battery, none of the lights on the front of the computer lit up. After reinstalling the battery and plugging the power cord back in, the light behind the power button is constantly illuminated (without even pressing the power button), but there is still no response to the power button, no fans turned on, nothing else that would indicate that it is running. System: Acer Aspire ASE700-UQ660A (Specs should be all factory defaults except:) 4 GB RAM Nvidia GeForce 8600 GT with driver version 197.45 Windows 7 Professional 64 bit

  Read the article

• Word 2007 files on emacs?

  - by Paul Nathan

  Is there a word-2007 mode for emacs?

  Read the article

• How can I determine what codec is being used?

  - by jldugger

  This forum comment and this superuser answer suggest that the audio compression contributes to loss of quality. I've noticed that music played over my BT setup sometimes pitch bends in ways I don't remember the original doing, and I'm wondering if SBC has something to do with it. I'm using Ubuntu 10.10 on a Mac Pro, connecting to a pair of Sony DR-BT50's. Is there a way to inspect which Bluetooth codec pulseaudio is using, what codecs both ends of the bluetooth link support?

  Read the article

• How can I remove UNC password from a file

  - by freddoo

  Hi we have an mp4 file on our web server in a virtual directory When we try to access the file we get prompted for a username/password. When I tried to change the path of the virtual directory I got the message 'The following child nodes also define the value of the "UNCPassword" property, which overrides the value you have just set ...' which included the mp4 file that we try to access. How can I remove the UNC Password securing the file? The file is not on a shared drive its on the same drive as the web site root. The funny thing is the path of the virtual directory is not a UNC path it's a full path on the same server d:.....

  Read the article

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Clean up infected computer from viruses

  - by ripper234

  I have a computer which had AVG Free installed from day one. After several months of operation, it starts detecting viruses and trojans all the time. Besides running a full scan, what should I do to clean the computer? Should I install another anti-virus or anti-malware tool (can it help?), or once viruses infect a system the only real solution is a clean format? (Lately I've heard of viruses that burn themselves in the BIOS, so a clean format might not always work ... how common is this technique? Should I burn a fresh BIOS as well?)

  Read the article

• Setting MacBook timezone to UTC

  - by Andy A

  To run my web app, I need to set my timezone to UTC on my MacBook. I can do this temporarily by opening a Konsole and entering sudo ln -sf /usr/share/zoneinfo/UTC /etc/localtime However, my timezone returns to normal when I restart my machine! Any advice? Edit : The response to this question by 'Celada' implies that I can just make my Server UTC. I am using Apache Tomcat 7. Adding to Celada's response, how can I make it UTC?

  Read the article

• Checking detailed memory information on Linux

  - by user35153

  I know that I can check CPU info via cat /proc/cpuinfo and memory info via cat /proc/meminfo. But cat /proc/meminfo yields results like the following: MemTotal: 66098352 kB MemFree: 329152 kB Buffers: 632432 kB Cached: 62619692 kB SwapCached: 0 kB Active: 6425444 kB Inactive: 58717276 kB SwapTotal: 1951888 kB SwapFree: 1951796 kB Dirty: 38416 kB Writeback: 0 kB AnonPages: 1890268 kB Mapped: 12624 kB Slab: 464580 kB SReclaimable: 275812 kB SUnreclaim: 188768 kB PageTables: 7524 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 35001064 kB Committed_AS: 3860248 kB VmallocTotal: 34359738367 kB VmallocUsed: 125636 kB VmallocChunk: 34359612527 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB I want to learn more about the clock speed of the memory (in Mhz?). How do I get that information?

  Read the article

• Linux Mint something wrong with my .bashrc

  - by user2309862

  The path of my .basrc file is /home/vamsi/.bashrc It is weird that my file has nothing but the path I set. I think I am using a file at the wrong location or that I have lost my .bashrc file as none of the environment variables set here seem to work. #ANDROID_DEV ANDROID_HOME=/opt/android-sdk-linux export ANDROID_HOME PATH= $PATH:$ANDROID_SDK_HOME/tools export PATH PATH=$PATH:$ANDROID_HOME/platform-tools export PATH PATH=$PATH:$ANDROID_HOME/build-tools export PATH #MAVEN-PATH M2_HOME=/opt/apache-maven-3.1.0 export M2_HOME M2=$PATH:$M2_HOME/bin export M2 I was prompted to install maven2 in order to use mvn, but the android command cannot be found. Could you please help me find a solution to this issue. EDIT: Meanwhile,I tried this: export PATH=${PATH}:/opt/android-sdk-linux/platform-tools export PATH=${PATH}:/opt/android-sdk-linux/tools Now,the output of $PATH echoes: bash: /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/opt/android-sdk-linux/platform-tools:/opt/android-sdk-linux/build-tools: No such file or directory

  Read the article

• Mouse button and keypress counter for Windows XP

  - by Yuval F

  I am trying to kick the habit of using a mouse where I could use keyboard shortcuts, for ergonomic reasons. I believe that if I see some statistics of my use of both input devices, I could reduce my use of mouse clicks. Do you know of any free software I can install on my Windows XP machine that counts keypresses and mouse button presses and displays an hourly/daily report? No fancy GUI is needed - just two summary lines.

  Read the article

• Scheduled task to map a network drive runs, but doesn't map the drive

  - by bikefixxer

  I have a task set up to run whenever the computer is logged onto that deletes all network folders and maps a network drive. Here is what is in the batch file: @echo off net use * /delete /y net use b: \\Server\Share /user:DOMAIN\Username password exit When the computer is restarted or logged off and back on, the task runs fine (according to the scheduled tasks window saying when it ran last) but the mapped drive doesn't show up. I'll open the command prompt and type "net use" and it simply says "There are no entries in the list". If I then right click on the task and run it, it works and the mapped drive shows up. I've checked the log and nothing shows up. I've tried adding a timer in the batch file so it waits 10 seconds (ping 1.1.1.1 -n 1 -w 10000nul) thinking that maybe the network wasn't connected, but that didn't work. What else can I try? Thanks!

  Read the article

• Mount canon sd 780 in Mac OS Snow Leopard as drive to get card contents?

  - by ayrad

  Hello, Is there any way to browse the contents of an SD card inside my canon digital camera using my macbook pro? I am trying to move the contents of the SD card to =a new SD card (with larger capacity). I do not have a card reader, only the usb cable that comes with the camera. Any ideas?

  Read the article

• Blank white desktop icons on new Windows 7 install

  - by SiegeX

  I just did a fresh install of Windows 7 professional on my father's Toshiba Satellite laptop and everything went smoothly except for the fact that certain desktop shortcuts appear as a blank white page. I've tried: going in and changing the icon to many different things reloading the icon cache by deleting the IconCache.db file uninstalling his Free AVG as he heard the virus scanner might be preventing it (it wasn't and he put it back.) The one thing these icons have in common is that they are shortcuts to some very old DOS executables. One of them is Word Star 2000 to give you an idea. Does anybody have any other suggestions besides what we've tried?

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >