Search Results

Search found 46833 results on 1874 pages for 'distributed system'.

Page 1790/1874 | < Previous Page | 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797  | Next Page >

  • My computer freezes irregurarly

    - by Manhim
    My computer started to freeze at irregular times for 3 weeks now. What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 50-60. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) My current to-try list Change the thermal paste on my CPU. Change my graphic card with a temporary one and stress the computer. Change my power supply. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

    Read the article

  • Apache sends plain-text response when accessing SSL-enabled site without HTTPS

    - by animuson
    I've never encountered something such as this before. I was attempting to simply redirect the page to the HTTPS version if it determined that HTTPS was off, but instead it's displaying an HTML page rather than actually redirecting; and even odder, it's displaying it as text/plain! The VirtualHost Declaration (Sort of): ServerAdmin [email protected] DocumentRoot "/path/to/files" ServerName example.com SSLEngine On SSLCertificateFile /etc/ssh/certify/example.com.crt SSLCertificateKeyFile /etc/ssh/certify/example.com.key SSLCertificateChainFile /etc/ssh/certify/sub.class1.server.ca.pem <Directory "/path/to/files/"> AllowOverride All Options +FollowSymLinks DirectoryIndex index.php Order allow,deny Allow from all </Directory> RewriteEngine On RewriteCond %{HTTPS} off RewriteRule .* https://example.com:6161 [R=301] The Page Output: <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>301 Moved Permanently</title> </head><body> <h1>Moved Permanently</h1> <p>The document has moved <a href="https://example.com:6161">here</a>.</p> <hr> <address>Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/1.0.0e DAV/2 Server at example.com Port 443</address> </body></html> I've tried moving the Rewrite stuff up above the SSL stuff hoping it'd do something and nothing happens. If I view the page with via HTTPS, it displays fine like it should. It's obviously detecting that I'm trying to rewrite the path, but it's not acting. The Apache error log does not indicate anything to me that might have gone wrong. When I remove the RewriteRules: <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>400 Bad Request</title> </head><body> <h1>Bad Request</h1> <p>Your browser sent a request that this server could not understand.<br /> Reason: You're speaking plain HTTP to an SSL-enabled server port.<br /> Instead use the HTTPS scheme to access this URL, please.<br /> <blockquote>Hint: <a href="https://example.com/"><b>https://example.com/</b></a></blockquote></p> <p>Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.</p> <hr> <address>Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/1.0.0e DAV/2 Server at example.com Port 443</address> </body></html> I get the standard "you can't do this because you're not using SSL" response, which is also provided in text/plain rather than being rendered as HTML. This would make sense, it should only work for HTTPS-enabled connections, but I still want to redirect them to the HTTPS connection when it determines that it is not enabled. Thinking I could circumvent the system: I tried adding a ErrorDocument 400 https://example.com:6161 to the config file instead of using RewriteRules, and that just gave me a new message, still no cheese. <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>302 Found</title> </head><body> <h1>Found</h1> <p>The document has moved <a href="https://example.com:6161">here</a>.</p> <hr> <address>Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/1.0.0e DAV/2 Server at example.com Port 443</address> </body></html> How can I force Apache to actually redirect rather than displaying a "301" page that shows HTML in plain-text format?

    Read the article

  • What is the best server or Ip address to use for prolonged testing?

    - by eldorel
    I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

    Read the article

  • NPM not installing dependencies?

    - by neezer
    Having trouble getting NPM to install dependencies with npm install -d in my project directory with a defined package.json file. Here's my package.json: https://gist.github.com/3068312 And after wiping my project root's node modules folder (rm -rf node_modules), I run npm install -d in my project root and am greeted with this: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm http GET https://registry.npmjs.org/sinon npm http GET https://registry.npmjs.org/underscore npm http GET https://registry.npmjs.org/mocha npm http GET https://registry.npmjs.org/request npm http 304 https://registry.npmjs.org/sinon npm http 304 https://registry.npmjs.org/underscore npm http 304 https://registry.npmjs.org/mocha npm http 304 https://registry.npmjs.org/request npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info unbuild /vagrant/node_modules/underscore npm info unbuild /vagrant/node_modules/mocha npm info unbuild /vagrant/node_modules/sinon npm info unbuild /vagrant/node_modules/request npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/underscore npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/underscore' npm ERR! Error: ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! You may report this log at: npm ERR! <http://bugs.debian.org/npm> npm ERR! or use npm ERR! reportbug --attach /vagrant/npm-debug.log npm npm ERR! npm ERR! System Linux 3.2.0-23-generic npm ERR! command "node" "/usr/bin/npm" "install" "-d" npm ERR! cwd /vagrant npm ERR! node -v v0.6.12 npm ERR! npm -v 1.1.4 npm ERR! path /vagrant/node_modules/underscore/package.json npm ERR! code ENOENT npm ERR! message ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! errno {} npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/request npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/request' npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /vagrant/npm-debug.log npm not ok If I rerun npm install -d, the error changes to whatever the next package is... if I keep running it it over and over again, it eventually doesn't complain anymore and outputs: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm info build /vagrant npm info linkStuff [email protected] npm info install [email protected] npm info postinstall [email protected] npm info ok However, none of the dependencies for any of these packages get installed. For instance, cheerio has a few dependencies, so when I try running my test suite, I'm greeted with: (ssh) /vagrant git:master ? mocha --compilers coffee:coffee-script --watch spec/* node.js:201 throw e; // process.nextTick error, or 'error' event on first tick ^ Error: Cannot find module 'cheerio-select' at Function._resolveFilename (module.js:332:11) at Function._load (module.js:279:25) at Module.require (module.js:354:17) What gives? I'm on Ubuntu Precise64 in a Vagrant virtual box.

    Read the article

  • How to use Public IP in case of two ISP when two differs from each other

    - by user1471995
    Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

    Read the article

  • Outlook Web Access, reverse proxy and browser

    - by M'vy
    Hi SF'ers! We recently moved an exchange server behind a reverse proxy due to the loss of a public IP. I've managed to configure the reverse proxy (httpd proxy_http). But there is a problem for the SSL configuration. When accessing the OWA interface with Firefox, all is ok and working. When accessing with MSIE or Chrome, they do not retrieve the good SSL Certificate. I think this is due to the multiples virtual host for httpd. Is there a workaround to make sure MSIE/Chrome request the certificate for the good domain name like FF does? Already tested with the SSL virtual host : SetEnvIf User-Agent ".*MSIE.*" value BrowserMSIE Header unset WWW-Authenticate Header add WWW-Authenticate "Basic realm=exchange.domain.com" A: ProxyPreserveHost On also: BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 Or: SetEnvIf User-Agent ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 And lots of ProxyPassand ProxyReversePath on /exchweb /exchange /public etc... And it still don't seem to work. Any clue? Thanks. Edit 1: Precision of versions # openssl version OpenSSL 0.9.8k-fips 25 Mar 2009 /usr/sbin/httpd -v Server version: Apache/2.2.11 (Unix) Server built: Mar 17 2009 09:15:10 Browser versions : MSIE : 8.0.6001 Opera: Version 11.01 Revision 1190 Firefox: 3.6.15 Chrome: 10.0.648.151 Operating System: Windows Vista 32bits. They are all SNI compliant, I've tested them this afternoon https://sni.velox.ch/ You're right Shane Madden, I have multiple sites on the same public IP (and same port as well). The server itself is just a reverse proxy, that rewrite addresses to internal servers. The default host is a dev site, configure with the certificate that does not match the OWA (of course... would have been to easy) <VirtualHost *:443> ServerName dev2.domain.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/error-%y%m%d.log 86400" LogLevel warn RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes SSLEngine on SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/domain.com.crt SSLCertificateKeyFile /etc/httpd/ssl/domain.com.key RewriteCond %{HTTP_HOST} dev2\.domain\.com RewriteRule ^/(.*)$ http://dev2.domain.com/$1 [L,P] </VirtualHost> The certificate of domain is a *.domain.com The second vHost is : <VirtualHost *:443> ServerName exchange.domain2.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/error-%y%m%d.log 86400" LogLevel warn SSLEngine on SSLProxyEngine On SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/exchange.pem SSLCertificateKeyFile /etc/httpd/ssl/exchange.key RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes RewriteCond %{HTTP_HOST} exchange\.domain2\.com RewriteRule ^/(.*)$ https://exchange.domain2.com/$1 [L,P] </VirtualHost> and it's certificate is exchange.domain2.com only. I presume the SNI is somewhere not activated on my server. The versions of openssl and apache seams to be ok for the SNI support. The only thing I do not know is if httpd has been compile with the good options. (I assume it's a fedora packet).

    Read the article

  • Why don't mails show up in the recipient's mailspool?

    - by Jason
    I have postfix dovecot running with local email system on thunderbird. I have two users on by ubuntu, mailuser 1 and mailuser 2 whom i added to thunderbird. Everything went fine, except the users dont have anything on their inbox on thunderbird and sent mails dont get through. Im using maildir as well. Checking /var/log/mail.log reveals this This what is happining: Restarting postfix and dovecot and then sending mail from one user to another user... I believe this line is the problem May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] Why is it not connecting ? What could be wrong ? /var/log/mail.log May 30 18:30:21 dovecot: imap: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: imap: Server shutting down. in=467 out=475 May 30 18:30:21 dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Dovecot v2.2.9 starting up (core dumps disabled) May 30 18:30:54 dovecot: imap-login: Login: user=<mailuser2>, method=PLAIN, rip=::1, lip=::1, mpid=12638, TLS, session=<xUfQkaD66gAAAAAAAAAAAAAAAAAAAAAB> May 30 18:31:04 postfix/master[12245]: terminating on signal 15 May 30 18:31:04 postfix/master[12795]: daemon started -- version 2.11.0, configuration /etc/postfix May 30 18:31:55 postfix/postscreen[12803]: CONNECT from [127.0.0.1]:33668 to [127.0.0.1]:25 May 30 18:31:55 postfix/postscreen[12803]: WHITELISTED [127.0.0.1]:33668 May 30 18:31:55 postfix/smtpd[12804]: connect from localhost[127.0.0.1] May 30 18:31:55 postfix/smtpd[12804]: 1ED7120EB9: client=localhost[127.0.0.1] May 30 18:31:55 postfix/cleanup[12809]: 1ED7120EB9: message-id=<[email protected]> May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: from=<[email protected]>, size=546, nrcpt=1 (queue active) May 30 18:31:55 postfix/local[12810]: 1ED7120EB9: to=<mailuser2@mysitecom>, relay=local, delay=0.03, delays=0.02/0.01/0/0, dsn=2.0.0, status=sent (delivered to maildir) May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: removed May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] May 30 18:31:55 dovecot: imap-login: Login: user=<mailuser1>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=12814, TLS, session=<sD9plaD6PgB/AAAB> This is my postfix main.cf See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination myhostname = server mydomain = mysite.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $mydomain mydestination = mysite.com #relayhost = smtp.192.168.10.1.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.10.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all home_mailbox = Maildir / mailbox_command= All ports are listening tcp 0 0 *:imaps *:* LISTEN tcp 0 0 *:submission *:* LISTEN tcp 0 0 *:imap2 *:* LISTEN tcp 0 0 s148134.s148134.:domain *:* LISTEN tcp 0 0 192.168.56.101:domain *:* LISTEN tcp 0 0 10.0.2.15:domain *:* LISTEN tcp 0 0 localhost:domain *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 localhost:953 *:* LISTEN tcp6 0 0 [::]:imaps [::]:* LISTEN tcp6 0 0 [::]:submission [::]:* LISTEN tcp6 0 0 [::]:imap2 [::]:* LISTEN tcp6 0 0 [::]:domain [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 [::]:smtp [::]:* LISTEN tcp6 0 0 localhost:953 [::]:* LISTEN

    Read the article

  • Tomcat and ASP site under IIS6 with SSL

    - by Rafe
    I've been working on migrating our companies' website from it's original server to a new one and am having two different but possibly related problems. The box this is sitting on is a Windows 2003 server x64 running IIS 6. The Tomcat version is 5.5.x as it was the version the original deployment was built on. There are two other sites on the server one in plain HTML, another in PHP and the one I am trying to migrate is a combination of Java and ASP (the introductory/sign in pages being Java as well as many reports used for our clients and the administration pages being in ASP) First of all I can only access the site if I enter the ip followed by :8080 (xxx.xxx.xxx.xxx:8080). The original setup had an index.html file in the root of the site with a bit of javascript in the header that pointed the site to 'www.mysite.com/app/public' but if I try going directly to the site without the 8080 I get a 'page not found error' and the javascript redirector causes the same problem because it doesn't add the 8080 into the URL even though on the original site the 8080 wasn't present so I don't understand why it would need it now. The js redirect looks like this: <script language="JavaScript"> <!-- location.href = "/app/public/" location.replace("/app/public/"); //--> </script> When setting the site up I used the command line to unbind IIS from all of the ip's on the system (there are 12 ip's on this box) because I was led to believe Tomcat wanted to use localhost which wasn't accessible. I'm not sure if this was the right thing to do but I'm throwing it in for the sake of completeness. And actually, at this point trying to go to localhost from the server itself throws up a 'could not connect to localhost' error. If I go to localhost:8080 I get the tomcat welcome page. If I do localhost:8080/app/public I get the intro page to our website. So I'm not sure what I'm even looking at in this case, that is what the proper behavior should be. The second part of the problem is that if I do go to either the ip or localhost such as above (localhost:8080/app/public) and click on our login link it is supposed to transfer me to our login page yet instead I receive a 'could not connect' error and the url has changed to localhost:8443/app/secure. From my research I see that port 8443 is Tomcats SSL port and the server.xml alludes to it as follows: <Connector port="8080" maxHttpHeaderSize="8192" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" /> I have an SSL certificate assigned to the site via IIS and was under the impression that by default Tomcat allowed IIS to handle secure connections but apparently something is munged because it's not working. There is another section in the server.xml that reads like this: <Connector port="8009" enableLookups="false" redirectPort="443" protocol="AJP/1.3" /> Which I'm not sure what it is for although port 443 is the SSL port that IIS uses so I'm confused as to what this is supposed to be doing. Another question I have is when does the isap_redirector actually come into play? How does it know when to try and serve pages through Tomcat and when not to? I've hunted around the 'net for an answer and have yet to find a clear dialogue on the subject. Anyone have any pointers as to where to look for a solution to all of this?

    Read the article

  • Drupal & nginx : a sound "general purpose" configuration?

    - by sbrattla
    After a bit back and forth with configuring Drupal and nginx to work together, I've come up with the below configuration for a site. It works well, both with private and public file systems. However, as I am fairly new to nginx I'd like to hear if there is something with this configuration that I should change (for Please note! I'm aiming towards getting feedback on a general purpose Drupal configuration. That is, a configuration which others who are trying out Drupal + nginx can "copy paste" to get up and running. server { listen 80; server_name www.example.* example.*; access_log /home/example/www/logs/access.log; error_log /home/example/www/logs/error.log; root /home/example/www/public_html; # Site Icon location = /favicon.ico { log_not_found off; access_log off; } # Search Engines location = /robots.txt { allow all; log_not_found off; access_log off; } # Drush location = /backup { deny all; } # Very rarely should these ever be accessed from outside # the local network. location ~* \.(txt|log)$ { allow 10.0.0.0/8; allow 172.16.0.0/12; allow 192.168.0.0/16; deny all; } location ~ \..*/.*\.php$ { return 403; } # Default location location / { try_files $uri @rewrite; } # Files managed by Drupal will be served via PHP. location ~* /system/files/ { access_log off; try_files $uri @rewrite; } ## Images and static content is treated different location ~* \.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; expires 30d; } # Some Drupal modules enforce no slash (/) at the end # of the URL. location @rewrite { rewrite_log on; rewrite ^/(.*)$ /index.php?q=$1; } # PHP5-FPM is used to handle PHP. location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(.*)$; fastcgi_pass unix:/var/run/example.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_intercept_errors on; fastcgi_ignore_client_abort off; fastcgi_connect_timeout 60; fastcgi_send_timeout 180; fastcgi_read_timeout 180; fastcgi_buffer_size 128k; fastcgi_buffers 4 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; } ## Disable viewing .htaccess & .htpassword location ~ /\.ht { deny all; } }

    Read the article

  • Connect to VPN from Mac on Time Capsule network

    - by Lou Franco
    I have a few clients on my network that can connect to my work VPN (Windows PPTP) when they are not on my home network. On my home network (Cable Modem with Time Capsule providing Wifi), it fails very early -- looks like it can't even establish a connection. Logs just say that it failed -- even verbose logs don't have much: I redacted the host and IP from this log, but I can ping it. Wed Feb 2 14:32:41 2011 : PPTP connecting to server 'XXX.XXX.com' (XXX.XX.XX.XX)... Wed Feb 2 14:32:41 2011 : PPTP connection established. Wed Feb 2 14:32:41 2011 : using link 0 Wed Feb 2 14:32:41 2011 : Using interface ppp0 Wed Feb 2 14:32:41 2011 : Connect: ppp0 <--> socket[34:17] Wed Feb 2 14:32:41 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:44 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:47 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:50 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:53 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:56 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:59 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:02 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:05 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:08 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:11 2011 : LCP: timeout sending Config-Requests Wed Feb 2 14:33:11 2011 : Connection terminated. Wed Feb 2 14:33:11 2011 : PPTP disconnecting... Wed Feb 2 14:33:11 2011 : PPTP disconnected Others can get to the VPN and I can too, but not on my network. The only clue I have seen in other forums is to set the NAT default host on the Time Capsule -- I set this to the IP that my mac got over DHCP. I made sure that my Mac gets a different range of IP addresses that it would get if it connected to the VPN (192.168.1.x vs. 10.0.0.x). Not using any VPN client -- just Network System Preferences. It has worked in the past -- but it was a while ago, so I can't pinpoint a change. My sysadmin doesn't even see incoming connections to the VPN (nothing logged about me when I connect). Looking for any diagnostic advice at all

    Read the article

  • Reconstructing the disk order in RAID 6 with 7 disks

    - by rkotulla
    a little background to this question first: I am running a RAID-6 within a QNAP TS869L external RAID/NAS system. I started with 5 disks of 3 TB each back in the day, and later added another 2 disks of 3TB to the RAID. The QNAP internals handled the growing and re-syncing etc, and everything seemd to be perfectly fine. About 2 weeks ago, I had one of the disks (disk #5, disk #2 has gone bad in the mean time) fail, and somehow (I have no idea why), also disks 1 and 2 got kicked out of the array. I replaced disk #5, but the RAID didn't start working again. After some calls to QNAP technical support, they re-created the array (using mdadm --create --force --assume-clean ...), but the resulting array couldn't find a filesystem, and I was kindly referred to contact a data recovery company that I can't afford. After some digging through old log files, resetting the disk to factory default, etc, I found a few errors that were made during this re-create - I wish I still had some of the original metadata, but unfortunately i don't (I definitely learned that lesson). I'm currently at the point where I know the correct chunk-size (64K), metadata-version (1.0; factory default was 0.9, but from what I read 0.9 doesn't handle disks over 2 TB, mine are 3 TB), and I now find the ext4 filesystem that should be on the disks. Only variable left to determine is the right disk order! I started using the description found in answer #4 of "Recover RAID 5 data after created new array instead of re-using" but am a little confused on what the order should be for a proper RAID-6. RAID-5 is pretty well documented in a number of places, but RAID-6 much less so. Also, does the layout, i.e. distribution of parity and data chunks across the disks, change after the growing of the array from 5 to 7 disks, or does the re-sync re-organize them in such a way a native 7-disk RAID-6 would have been? Thanks some more mdadm output that might be helpful: mdadm version: [~] # mdadm --version mdadm - v2.6.3 - 20th August 2007 mdadm details from one of the disks in the array: [~] # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 1.0 Feature Map : 0x0 Array UUID : 1c1614a5:e3be2fbb:4af01271:947fe3aa Name : 0 Creation Time : Tue Jun 10 10:27:58 2014 Raid Level : raid6 Raid Devices : 7 Used Dev Size : 5857395112 (2793.02 GiB 2998.99 GB) Array Size : 29286975360 (13965.12 GiB 14994.93 GB) Used Size : 5857395072 (2793.02 GiB 2998.99 GB) Super Offset : 5857395368 sectors State : clean Device UUID : 7c572d8f:20c12727:7e88c888:c2c357af Update Time : Tue Jun 10 13:01:06 2014 Checksum : d275c82d - correct Events : 7036 Chunk Size : 64K Array Slot : 0 (0, 1, failed, 3, failed, 5, 6) Array State : Uu_u_uu 2 failed mdadm details for the array in the current disk-order (based on my best guess reconstructed from old log-files) [~] # mdadm --detail /dev/md0 /dev/md0: Version : 01.00.03 Creation Time : Tue Jun 10 10:27:58 2014 Raid Level : raid6 Array Size : 14643487680 (13965.12 GiB 14994.93 GB) Used Dev Size : 2928697536 (2793.02 GiB 2998.99 GB) Raid Devices : 7 Total Devices : 5 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Jun 10 13:01:06 2014 State : clean, degraded Active Devices : 5 Working Devices : 5 Failed Devices : 0 Spare Devices : 0 Chunk Size : 64K Name : 0 UUID : 1c1614a5:e3be2fbb:4af01271:947fe3aa Events : 7036 Number Major Minor RaidDevice State 0 8 3 0 active sync /dev/sda3 1 8 19 1 active sync /dev/sdb3 2 0 0 2 removed 3 8 51 3 active sync /dev/sdd3 4 0 0 4 removed 5 8 99 5 active sync /dev/sdg3 6 8 83 6 active sync /dev/sdf3 output from /proc/mdstat (md8, md9, and md13 are internally used RAIDs holding swap, etc; the one I'm after is md0) [~] # more /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md0 : active raid6 sdf3[6] sdg3[5] sdd3[3] sdb3[1] sda3[0] 14643487680 blocks super 1.0 level 6, 64k chunk, algorithm 2 [7/5] [UU_U_UU] md8 : active raid1 sdg2[2](S) sdf2[3](S) sdd2[4](S) sdc2[5](S) sdb2[6](S) sda2[1] sde2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdg4[3] sdf4[4] sde4[5] sdd4[6] sdc4[2] sdb4[1] sda4[0] 458880 blocks [8/7] [UUUUUUU_] bitmap: 21/57 pages [84KB], 4KB chunk md9 : active raid1 sdg1[6] sdf1[5] sde1[4] sdd1[3] sdc1[2] sda1[0] sdb1[1] 530048 blocks [8/7] [UUUUUUU_] bitmap: 37/65 pages [148KB], 4KB chunk unused devices: <none>

    Read the article

  • How can I check if PHP was compiled with the UNICODE version of the Win32 API?

    - by Wesley Murch
    This is related to this Stack Overflow post: glob() can't find file names with multibyte characters on Windows? I'm having issues with PHP and files that have multibyte characters on Windows. Here's my test case: print_r(scandir('./uploads/')); print_r(glob('./uploads/*')); Correct Output on remote UNIX server: Array ( [0] => . [1] => .. [2] => filename-äöü.jpg [3] => filename.jpg [4] => test?test.jpg [5] => ??? ?????.jpg [6] => ?????????.jpg [7] => ???.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg [2] => ./uploads/test?test.jpg [3] => ./uploads/??? ?????.jpg [4] => ./uploads/?????????.jpg [5] => ./uploads/???.jpg ) Incorrect Output locally on Windows: Array ( [0] => . [1] => .. [2] => ??? ?????.jpg [3] => ???.jpg [4] => ?????????.jpg [5] => filename-äöü.jpg [6] => filename.jpg [7] => test?test.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg ) Here's a relevant excerpt from the answer I chose to accept (which actually is a quote from an article that was posted online over 2 years ago): From the comments on this article: http://www.rooftopsolutions.nl/blog/filesystem-encoding-and-php The output from your PHP installation on Windows is easy to explain : you installed the wrong version of PHP, and used a version not compiled to use the Unicode version of the Win32 API. For this reason, the filesystem calls used by PHP will use the legacy "ANSI" API and so the C/C++ libraries linked with this version of PHP will first try to convert yout UTF-8-encoded PHP string into the local "ANSI" codepage selected in the running environment (see the CHCP command before starting PHP from a command line window) Your version of Windows is MOST PROBABLY NOT responsible of this weird thing. Actually, this is YOUR version of PHP which is not compiled correctly, and that uses the legacy ANSI version of the Win32 API (for compatibility with the legacy 16-bit versions of Windows 95/98 whose filesystem support in the kernel actually had no direct support for Unicode, but used an internal conversion layer to convert Unicode to the local ANSI codepage before using the actual ANSI version of the API). Recompile PHP using the compiler option to use the UNICODE version of the Win32 API (which should be the default today, and anyway always the default for PHP installed on a server that will NEVER be Windows 95 or Windows 98...) I can't confirm whether this is my problem or not. I used phpinfo() and did not find anything interesting, but I wasn't sure what to look for. I've been using XAMPP for easy installations, so I'm really not sure exactly how it was installed. I'm using Windows 7, 64 bit - so forgive my ignorance, but I'm not even sure if "Win32" is relevant here. How can I check if my current version of PHP was compiled with the configuration mentioned above? PHP Version: 5.3.8 System: Windows NT WES-PC 6.1 build 7601 (Windows 7 Home Premium Edition Service Pack 1) i586 Build Date: Aug 23 2011 11:47:20 Compiler: MSVC9 (Visual C++ 2008) Architecture: x86 Configure Command: cscript /nologo configure.js "--enable-snapshot-build" "--disable-isapi" "--enable-debug-pack" "--disable-isapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=D:\php-sdk\oracle\instantclient11\sdk,shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze"

    Read the article

  • Squid - Logging to MySQL without empty rows/skipped records?

    - by Lee Ward
    I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

    Read the article

  • Pushing DNSSEC updates with offline keys

    - by eggyal
    In a non-professional capacity, I look after the DNS of some 18 domains: mostly personal/vanity domains for immediate family. I outsource the whole shebang to an inexpensive managed hosting provider with a web interface through which I manage the zones; since the provider also offers DNSSEC, I have successfully deployed that too. These domains are so unimportant that an attack targetted against them seems much less likely than a general compromise of my provider's systems, at which point the records of all their customers might be changed to misdirect traffic (perhaps with extremely long TTLs). DNSSEC could protect against such an attack, but only if the zone's private keys are not held by the hosting provider. So, I wonder: how can one keep DNSSEC private keys offline yet still transfer signed zones to an outsourced DNS host? The most obvious answer (to me, at least) is to run one's own shadow/hidden master (from which the provider can slave) and then copy offline-signed zonefiles to the master as required. The problem is that the only machine I (want to*) control is my personal laptop, which usually connects from a typical home ADSL (behind NAT over a dynamically-assigned IP address). Having them slave from that (e.g. with a very long Expiry time on the zone for periods when my laptop is offline/unavailable) would not only require a Dynamic DNS record from which they can slave (if indeed they can slave from a named host rather than a static IP address), but would also involve me running a DNS server on my laptop and opening both it and my home network up to the incoming zone transfer requests: not ideal. I would prefer a much more push-oriented design, whereby my laptop initiates transfer of offline-signed zonefiles/updates to the provider's servers. I looked into whether nsupdate could fit the bill: documentation is a little sketchy, but my testing (with BIND 9.7) suggests it can indeed update DNSSEC zones, but only where the server holds the keys to perform the zone signing; I have not found a way to have it take an update including the relevant RRSIG/NSEC/etc. records and have the server accept them. Is this a supported use-case? If not, I suspect the only solutions which could fit the bill will involve non-DNS-based transfer of the zone updates and would welcome recommendations that are supported by (hopefully inexpensive) hosting providers: SFTP/SCP? rsync? RDBMS replication? Proprietary API? Finally, what would be the practical implications of such a setup? Key rotation is jumping out at me as being an obvious difficulty, especially if my laptop is offline for extended periods. But the zones are extremely stable, so perhaps I could get away with long-lived ZSKs**...? * Whilst I could run a shadow/hidden master on e.g. an outsourced VPS, I dislike the overhead of having to secure / manage / monitor / maintain yet another system; not to mention the additional financial costs of so doing. ** Okay, this would enable a concerted attacker to replay outdated records—but the risk and impact of such are both tolerable in the case of these domains.

    Read the article

  • Vista 64-bit, DISK BOOT FAILURE

    - by weka
    So I have this Acer Aspire AX3200-U3600A with Windows Vista (64-bit). Every night I turn it off and turn it back on in the morning. Around three weeks ago, I did a fresh factory reimage. Good as new. Then around two days ago, when I turned it on, I noticed it was running extremly slow. As in, it would often freeze up while I had multiple applications open when it usually never froze up. So I decided to restart my computer. Big mistake. My computer froze right after I clicked shut-down. I waited a while. Nothing. Waited some minutes. Nope. I decided to shut it down by pressing the power button. Here is where the problems begin. When I turned it back on, I saw the Windows logo and loading bar and then it loaded to black. I turned it off again forcefully by power button and then once more... then I got: AMD Data Change... Update New Data to DMI! then later the screen clears and I get: AHCI Option ROM BIOS Revision: 01.05.92 Date: 02-19-2008 Copyright (c) 2006-2008 Phoenix Technologies, LTD Port 01: Reset Port Error!! Port 02: then the screen clears again but this time, this loads from the bottom: Nvidia Boot Agent 249.0542 (copyright stuff... blah blah) PXE-E61: Media test failure, check cable. PXE-M0F: Exiting Nvidia Boot Agent DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER. So I try to go into Safe Mode. Well, first of all it doesn't load as fast. After it loads disk.sys from windows/drivers, it will wait a while (2-3 mins) THEN load. However it loads the Acer eRecovery Management Tool. I have three options: Reset computer to factory default, Restore computer from user's backup, or Exit. However, the top two options are gray and disabled where as the Exit is in blue and definitely clickable. So obviously safe mode is not there... A strong thing to note: In the beginning when all of this started, I did a Boot Windows Normal from pressing f8 and I got to my desktop! It logged me in. I could see the icons on my files. However my desktop was extremely slow as in when I clicked on the Start menu, it would wait a while, then load up the menu with JUST the gradient, no text or icons... so as you can see... it saw my HDD? Also, before anyone says, I have NO USB plugged in. My mouse and keyboard are not USB inputs, I assure you. And this came without a recovery CD AND when I went in BIOS, to change the BOOT ORDER, I did NOT see a CD-ROM option. And when I tried pressing ALT+F10 to get into Acer eRecovery Management, the top two options were disabled as well. But sometimes on start-up, I get: Windows has encountered a problem communicating with a device connected to your computer. This error can be caused by unplugging a removable storage device such as an external USB drive while the device is in use, or by faulty hardware such as a hard drive or CD-ROM drive that is failing. Make sure any removeable storage is properly connected and then restart your computer. If you continue to receive this error message, contact the hardware manufacturer. Status: 0xc00000e9 Info: An unexpected I/O error has occured. Then I tried Last Known Good Configuration Settings, that gives me a BSOD. What should I do/

    Read the article

  • linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

    - by devicerandom
    We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

    Read the article

  • x11vnc working in Ubuntu 10.10

    - by pablorc
    I'm trying to start x11vnc in a Ubuntu 10.10 (my server is in Amazon EC2), but I have the next error $ sudo x11vnc -forever -usepw -httpdir /usr/share/vnc-java/ -httpport 5900 -auth /usr/sbin/gdm 25/11/2010 13:29:51 passing arg to libvncserver: -httpport 25/11/2010 13:29:51 passing arg to libvncserver: 5900 25/11/2010 13:29:51 -usepw: found /home/ubuntu/.vnc/passwd 25/11/2010 13:29:51 x11vnc version: 0.9.10 lastmod: 2010-04-28 pid: 3504 25/11/2010 13:29:51 XOpenDisplay(":0.0") failed. 25/11/2010 13:29:51 Trying again with XAUTHLOCALHOSTNAME=localhost ... 25/11/2010 13:29:51 *************************************** 25/11/2010 13:29:51 *** XOpenDisplay failed (:0.0) *** x11vnc was unable to open the X DISPLAY: ":0.0", it cannot continue. *** There may be "Xlib:" error messages above with details about the failure. Some tips and guidelines: ** An X server (the one you wish to view) must be running before x11vnc is started: x11vnc does not start the X server. (however, see the -create option if that is what you really want). ** You must use -display <disp>, -OR- set and export your $DISPLAY environment variable to refer to the display of the desired X server. - Usually the display is simply ":0" (in fact x11vnc uses this if you forget to specify it), but in some multi-user situations it could be ":1", ":2", or even ":137". Ask your administrator or a guru if you are having difficulty determining what your X DISPLAY is. ** Next, you need to have sufficient permissions (Xauthority) to connect to the X DISPLAY. Here are some Tips: - Often, you just need to run x11vnc as the user logged into the X session. So make sure to be that user when you type x11vnc. - Being root is usually not enough because the incorrect MIT-MAGIC-COOKIE file may be accessed. The cookie file contains the secret key that allows x11vnc to connect to the desired X DISPLAY. - You can explicitly indicate which MIT-MAGIC-COOKIE file should be used by the -auth option, e.g.: x11vnc -auth /home/someuser/.Xauthority -display :0 x11vnc -auth /tmp/.gdmzndVlR -display :0 you must have read permission for the auth file. See also '-auth guess' and '-findauth' discussed below. ** If NO ONE is logged into an X session yet, but there is a greeter login program like "gdm", "kdm", "xdm", or "dtlogin" running, you will need to find and use the raw display manager MIT-MAGIC-COOKIE file. Some examples for various display managers: gdm: -auth /var/gdm/:0.Xauth -auth /var/lib/gdm/:0.Xauth kdm: -auth /var/lib/kdm/A:0-crWk72 -auth /var/run/xauth/A:0-crWk72 xdm: -auth /var/lib/xdm/authdir/authfiles/A:0-XQvaJk dtlogin: -auth /var/dt/A:0-UgaaXa Sometimes the command "ps wwwwaux | grep auth" can reveal the file location. Starting with x11vnc 0.9.9 you can have it try to guess by using: -auth guess (see also the x11vnc -findauth option.) Only root will have read permission for the file, and so x11vnc must be run as root (or copy it). The random characters in the filenames will of course change and the directory the cookie file resides in is system dependent. See also: http://www.karlrunge.com/x11vnc/faq.html I've already tried with some -auth options but the error persist. I have gdm running. Thank you in advance

    Read the article

  • VPS 512 MB RAM with WordPressMU comes to consumes lots of memory

    - by CAPitalZ
    I have googled for days and gathered all optimization suggestions and tried. My sites are not getting any high hits. May be like 100 hits per day [all my sites combined]. Here are my specs I have 512 MB RAM VPS with burstable 1024 MB. Centos 5 32-bit & cPanel/WHM Apache 2.2 MySQL 5.0 PHP 5.3.2 Here is my Configs I have 2 WordPressMU production sites, and 1 test site my.cnf # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/lib/mysql/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/lib/mysql/mysql.sock skip-locking skip-bdb skip-innodb key_buffer = 16M max_allowed_packet = 1M table_cache = 64 sort_buffer_size = 512K net_buffer_length = 8K read_buffer_size = 256K read_rnd_buffer_size = 512K myisam_sort_buffer_size = 8M #CAPitalZ thread_cache_size=8 thread_concurrency=4 #query_cache_type=1 #query_cache_limit=1M query_cache_size=16M concurrent_insert=2 low_priority_updates=1 max_connections=50 tmp_table_size=16M max_heap_table_size=16M join_buffer_size=1M interactive_timeout=25 wait_timeout=1000 #connect_timout=10 not able to restart mysql max_connect_errors=10 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # skip-networking # Disable Federated by default skip-federated # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 [mysqld_safe] open_files_limit=8192 [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [myisamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [mysqlhotcopy] interactive-timeout httpd.conf I have unselected many modules and recompiled using EasyApache in WHM. Only have the following modules built Deflate Expires Fileprotect Imagemap MPM Prefork Version [default] EAccelerator for PHP Bcmath Calendar CurlSSL [I'm using Curl. But I don't have any https sites] Expat GD [for image cropping] Gettext Imap Mbregex [default] Mbstring [need both Mbregex and Mbstring for utf-8] Mysql of the system MySQL "Improved" extension. Sockets TTF (FreeType) [I'm using custom font] Zlib Under Global Configuration I only have FollowSymLinks enabled I Have TraceEnable, ServerSignature, FileETag OFF ServerTokens ProductOnly DirectoryIndex Priority has index.php as the first one I have removed Clamd [Clam Anti-virus] SpamAssasin is Off Under Tweak Settings Default catch-all/default address behavior for new accounts. This is set to "fail" All stats programs turned off I have eAccelerator installed and checked in phpinfo and its working [Pre VirtualHost Include under WHM] Timeout 20 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 3 MinSpareServers 1 MaxSpareServers 3 StartServers 1 ServerLimit 50 MaxClients 50 MaxRequestsPerChild 4000 ExtendedStatus Off #ServerType standalone this throws error HostnameLookups Off <Directory "/"> AllowOverride None </Directory> My sites will take ages to load and WHM/CPanel will not even load. adadaa.com/ http://adadaa.net/ kadais.ca/ My average memory consumption is like 1000 MB! [yes always bursting] The process that consumes most CPU and also most memory is mysql But I also get like 15 httpd processes [when its bursting] I already got warning from cpuwatchcheck saying "While processing, the cpu has been maxed out for more than a 6 hour period. The current load/uptime line on the server at the time of this email is 07:00:37 up 11:30, 0 users, load average: 14.64, 16.79, 20.07" I don't know, I have tried switching these config values many different times, but nothing seems to work. Please show some light... Thanks

    Read the article

  • RedHat 5.5 server does not show per processor memory utilization

    - by Mike S
    I have been searching all over internet but not finding any leads. I have a system with a memory leak that I am trying to troubleshoot. Unfortunately I am not able to see per processor memory utilization. Here are the outputs of TOP and PS commands. Linux SERVER_NAME 2.6.18-194.8.1.el5 #1 SMP Wed Jun 23 10:52:51 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux top - 09:17:13 up 18:43, 3 users, load average: 0.00, 0.00, 0.00 Tasks: 375 total, 1 running, 373 sleeping, 0 stopped, 1 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32922828k total, 32776712k used, 146116k free, 267128k buffers Swap: 5245212k total, 0k used, 5245212k free, 32141044k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 10348 744 620 S 0.0 0.0 0:05.65 init 2 root RT -5 0 0 0 S 0.0 0.0 0:00.05 migration/0 3 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/0 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 5 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/1 6 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/1 7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 8 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/2 9 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/2 10 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/2 11 root RT -5 0 0 0 S 0.0 0.0 0:00.01 migration/3 12 root 34 19 0 0 0 S 0.0 0.0 0:00.01 ksoftirqd/3 13 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/3 14 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/4 15 root 34 19 0 0 0 S 0.0 0.0 0:00.01 ksoftirqd/4 16 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/4 17 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/5 18 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/5 19 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/5 20 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/6 % ps -auxf | sort -nr -k 4 | head -10 Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ xfs 6205 0.0 0.0 23316 3892 ? Ss Aug19 0:00 xfs -droppriv -daemon uuidd 6101 0.0 0.0 60976 224 ? Ss Aug19 0:00 /usr/sbin/uuidd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND smmsp 6130 0.0 0.0 57900 1784 ? Ss Aug19 0:00 sendmail: Queue runner@01:00:00 for /var/spool/clientmqueue rpc 5126 0.0 0.0 8052 632 ? Ss Aug19 0:00 portmap root 99 0.0 0.0 0 0 ? S< Aug19 0:00 [events/1] root 98 0.0 0.0 0 0 ? S< Aug19 0:00 [events/0] root 97 0.0 0.0 0 0 ? S< Aug19 0:00 [watchdog/31] root 96 0.0 0.0 0 0 ? SN Aug19 0:00 [ksoftirqd/31] root 95 0.0 0.0 0 0 ? S< Aug19 0:00 [migration/31] Any help with this is appretiate.

    Read the article

  • volume group disappeared after xfs_check run

    - by John P
    EDIT** I have a volume group consisting of 5 RAID1 devices grouped together into a lvm and formatted with xfs. The 5th RAID device lost its RAID config (cat /proc/mdstat does not show anything). The two drives are still present (sdj and sdk), but they have no partitions. The LVM appeared to be happily using sdj up until recently. (doing a pvscan showed the first 4 RAID1 devices + /dev/sdj) I removed the LVM from the fstab, rebooted, then ran xfs_check on the LV. It ran for about half an hour, then stopped with an error. I tried rebooting again, and this time when it came up, the logical volume was no longer there. It is now looking for /dev/md5, which is gone (though it had been using /dev/sdj earlier). /dev/sdj was having read errors, but after replacing the SATA cable, those went away, so the drive appears to be fine for now. Can I modify the /etc/lvm/backup/dedvol, change the device to /dev/sdj and do a vgcfgrestore? I could try doing a pvcreate --uuid KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ /dev/sdj to make it recognize it, but I'm afraid that would erase the data on the drive UPDATE: just changing the pv to point to /dev/sdj did not work vgcfgrestore --file /etc/lvm/backup/dedvol dedvol Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Cannot restore Volume Group dedvol with 1 PVs marked as missing. Restore failed. pvscan /dev/sdj: read failed after 0 of 4096 at 0: Input/output error Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. PV /dev/sdd2 VG VolGroup00 lvm2 [74.41 GB / 0 free] PV /dev/md2 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md3 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md0 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md4 VG dedvol lvm2 [931.51 GB / 0 free] PV unknown device VG dedvol lvm2 [1.82 TB / 63.05 GB free] Total: 6 [5.53 TB] / in use: 6 [5.53 TB] / in no VG: 0 [0 ] vgscan Reading all physical volumes. This may take a while... /dev/sdj: read failed after 0 of 4096 at 0: Input/output error /dev/sdj: read failed after 0 of 4096 at 2000398843904: Input/output error Found volume group "VolGroup00" using metadata type lvm2 Found volume group "dedvol" using metadata type lvm2 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 5 Metadata Sequence No 10 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 5 Act PV 5 VG Size 5.46 TB PE Size 4.00 MB Total PE 1430796 Alloc PE / Size 1414656 / 5.40 TB Free PE / Size 16140 / 63.05 GB VG UUID o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246 dedvol { id = "o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246" seqno = 10 status = ["RESIZEABLE", "READ", "WRITE"] flags = [] extent_size = 8192 # 4 Megabytes max_lv = 0 max_pv = 0 physical_volumes { pv0 { id = "Msiee7-Zovu-VSJ3-Y2hR-uBVd-6PaT-Ho9v95" device = "/dev/md2" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv1 { id = "ZittCN-0x6L-cOsW-v1v4-atVN-fEWF-e3lqUe" device = "/dev/md3" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv2 { id = "NRNo0w-kgGr-dUxA-mWnl-bU5v-Wld0-XeKVLD" device = "/dev/md0" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv3 { id = "2EfLFr-JcRe-MusW-mfAs-WCct-u4iV-W0pmG3" device = "/dev/md4" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv4 { id = "KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ" device = "/dev/md5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 3907028992 # 1.81935 Terabytes pe_start = 384 pe_count = 476932 # 1.81935 Terabytes } }

    Read the article

  • How do I allow mysqld to use more than 24.9% of my cpu?

    - by Joseph Yancey
    I have a Web server running on RHEL that is running Apache and MySQL. It has a Quad core 3.2Ghz Xeon CPU and 8 Gigs of RAM Most of the time, we don't have any issues at all. Our web application is very database intensive. When our usage gets pretty heavy MySQL will peg out at using 24.9% of the cpu. Most of the time, it hangs around below 5%. I have speculated that it is only using one core of the CPU and it is pegging out that core but TOP shows me in the cpu column that mysqld changes cores even while the usage stays at 24.9%. When it does this MySQL gets painfully slow as it is queuing up queries Is there some magic configuration that will tell mysql to use more cpu when it needs to? Also, any other advice on my configuration would be helpful. We run two applications on this server. One that runs Innodb but doesn't get much usage (it has been replaced by the other app), and one that runs MyIsam and gets lots of use. Overall, our whole mysql data directory is something like 13Gigs if that matters at all. Here is my config: [root@ProductionLinux root]# cat /etc/my.cnf [mysqld] server-id = 71 log-bin = /var/log/mysql/mysql-bin.log binlog-do-db = oldapplication binlog-do-db = newapplication binlog-do-db = support thread_cache_size = 30 key_buffer_size = 256M table_cache = 256 sort_buffer_size = 4M read_buffer_size = 1M skip-name-resolve innodb_data_home_dir = /usr/local/mysql/data/ innodb_data_file_path = InnoDB:100M:autoextend set-variable = innodb_buffer_pool_size=70M set-variable = innodb_additional_mem_pool_size=10M set-variable = max_connections=500 innodb_log_group_home_dir = /usr/local/mysql/data innodb_log_arch_dir = /usr/local/mysql/data set-variable = innodb_log_file_size=20M set-variable = innodb_log_buffer_size=8M innodb_flush_log_at_trx_commit = 1 log-queries-not-using-indexes log-error = /var/log/mysql/mysql-error.log mysql show variables; +---------------------------------+-----------------------------------------------------------------------------+ | Variable_name | Value | +---------------------------------+-----------------------------------------------------------------------------+ | auto_increment_increment | 1 | | auto_increment_offset | 1 | | automatic_sp_privileges | ON | | back_log | 50 | | basedir | /usr/local/mysql-standard-5.0.18-linux-x86_64-glibc23/ | | binlog_cache_size | 32768 | | bulk_insert_buffer_size | 8388608 | | character_set_client | latin1 | | character_set_connection | latin1 | | character_set_database | latin1 | | character_set_results | latin1 | | character_set_server | latin1 | | character_set_system | utf8 | | character_sets_dir | /usr/local/mysql-standard-5.0.18-linux-x86_64-glibc23/share/mysql/charsets/ | | collation_connection | latin1_swedish_ci | | collation_database | latin1_swedish_ci | | collation_server | latin1_swedish_ci | | completion_type | 0 | | concurrent_insert | 1 | | connect_timeout | 5 | | datadir | /usr/local/mysql/data/ | | date_format | %Y-%m-%d | | datetime_format | %Y-%m-%d %H:%i:%s | | default_week_format | 0 | | delay_key_write | ON | | delayed_insert_limit | 100 | | delayed_insert_timeout | 300 | | delayed_queue_size | 1000 | | div_precision_increment | 4 | | engine_condition_pushdown | OFF | | expire_logs_days | 0 | | flush | OFF | | flush_time | 0 | | | ft_max_word_len | 84 | | ft_min_word_len | 4 | | ft_query_expansion_limit | 20 | | ft_stopword_file | (built-in) | | group_concat_max_len | 1024 | | have_archive | YES | | have_bdb | NO | | have_blackhole_engine | NO | | have_compress | YES | | have_crypt | YES | | have_csv | NO | | have_example_engine | NO | | have_federated_engine | NO | | have_geometry | YES | | have_innodb | YES | | have_isam | NO | | have_ndbcluster | NO | | have_openssl | NO | | have_query_cache | YES | | have_raid | NO | | have_rtree_keys | YES | | have_symlink | YES | | init_connect | | | init_file | | | init_slave | | | innodb_additional_mem_pool_size | 10485760 | | innodb_autoextend_increment | 8 | | innodb_buffer_pool_awe_mem_mb | 0 | | innodb_buffer_pool_size | 73400320 | | innodb_checksums | ON | | innodb_commit_concurrency | 0 | | innodb_concurrency_tickets | 500 | | innodb_data_file_path | InnoDB:100M:autoextend | | innodb_data_home_dir | /usr/local/mysql/data/ | | innodb_doublewrite | ON | | innodb_fast_shutdown | 1 | | innodb_file_io_threads | 4 | | innodb_file_per_table | OFF | | innodb_flush_log_at_trx_commit | 1 | | innodb_flush_method | | | innodb_force_recovery | 0 | | innodb_lock_wait_timeout | 50 | | innodb_locks_unsafe_for_binlog | OFF | | innodb_log_arch_dir | /usr/local/mysql/data | | innodb_log_archive | OFF | | innodb_log_buffer_size | 8388608 | | innodb_log_file_size | 20971520 | | innodb_log_files_in_group | 2 | | innodb_log_group_home_dir | /usr/local/mysql/data | | innodb_max_dirty_pages_pct | 90 | | innodb_max_purge_lag | 0 | | innodb_mirrored_log_groups | 1 | | innodb_open_files | 300 | | innodb_support_xa | ON | | innodb_sync_spin_loops | 20 | | innodb_table_locks | ON | | innodb_thread_concurrency | 20 | | innodb_thread_sleep_delay | 10000 | | interactive_timeout | 28800 | | join_buffer_size | 131072 | | key_buffer_size | 268435456 | | key_cache_age_threshold | 300 | | key_cache_block_size | 1024 | | key_cache_division_limit | 100 | | language | /usr/local/mysql-standard-5.0.18-linux-x86_64-glibc23/share/mysql/english/ | | large_files_support | ON | | large_page_size | 0 | | large_pages | OFF | | license | GPL | | local_infile | ON | | locked_in_memory | OFF | | log | OFF | | log_bin | ON | | log_bin_trust_function_creators | OFF | | log_error | /var/log/mysql/mysql-error.log | | log_slave_updates | OFF | | log_slow_queries | OFF | | log_warnings | 1 | | long_query_time | 10 | | low_priority_updates | OFF | | lower_case_file_system | OFF | | lower_case_table_names | 0 | | max_allowed_packet | 1048576 | | max_binlog_cache_size | 18446744073709551615 | | max_binlog_size | 1073741824 | | max_connect_errors | 10 | | max_connections | 500 | | max_delayed_threads | 20 | | max_error_count | 64 | | max_heap_table_size | 16777216 | | max_insert_delayed_threads | 20 | | max_join_size | 18446744073709551615 | | max_length_for_sort_data | 1024 | | max_relay_log_size | 0 | | max_seeks_for_key | 18446744073709551615 | | max_sort_length | 1024 | | max_sp_recursion_depth | 0 | | max_tmp_tables | 32 | | max_user_connections | 0 | | max_write_lock_count | 18446744073709551615 | | multi_range_count | 256 | | myisam_data_pointer_size | 6 | | myisam_max_sort_file_size | 9223372036854775807 | | myisam_recover_options | OFF | | myisam_repair_threads | 1 | | myisam_sort_buffer_size | 8388608 | | myisam_stats_method | nulls_unequal | | net_buffer_length | 16384 | | net_read_timeout | 30 | | net_retry_count | 10 | | net_write_timeout | 60 | | new | OFF | | old_passwords | OFF | | open_files_limit | 2510 | | optimizer_prune_level | 1 | | optimizer_search_depth | 62 | | pid_file | /usr/local/mysql/data/ProductionLinux.pid | | port | 3306 | | preload_buffer_size | 32768 | | protocol_version | 10 | | query_alloc_block_size | 8192 | | query_cache_limit | 1048576 | | query_cache_min_res_unit | 4096 | | query_cache_size | 0 | | query_cache_type | ON | | query_cache_wlock_invalidate | OFF | | query_prealloc_size | 8192 | | range_alloc_block_size | 2048 | | read_buffer_size | 1044480 | | read_only | OFF | | read_rnd_buffer_size | 262144 | | relay_log_purge | ON | | relay_log_space_limit | 0 | | rpl_recovery_rank | 0 | | secure_auth | OFF | | server_id | 71 | | skip_external_locking | ON | | skip_networking | OFF | | skip_show_database | OFF | | slave_compressed_protocol | OFF | | slave_load_tmpdir | /tmp/ | | slave_net_timeout | 3600 | | slave_skip_errors | OFF | | slave_transaction_retries | 10 | | slow_launch_time | 2 | | socket | /tmp/mysql.sock | | sort_buffer_size | 4194296 | | sql_mode | | | sql_notes | ON | | sql_warnings | ON | | storage_engine | MyISAM | | sync_binlog | 0 | | sync_frm | ON | | sync_replication | 0 | | sync_replication_slave_id | 0 | | sync_replication_timeout | 10 | | system_time_zone | CST | | table_cache | 256 | | table_lock_wait_timeout | 50 | | table_type | MyISAM | | thread_cache_size | 30 | | thread_stack | 262144 | | time_format | %H:%i:%s | | time_zone | SYSTEM | | timed_mutexes | OFF | | tmp_table_size | 33554432 | | tmpdir | | | transaction_alloc_block_size | 8192 | | transaction_prealloc_size | 4096 | | tx_isolation | REPEATABLE-READ | | updatable_views_with_limit | YES | | version | 5.0.18-standard-log | | version_comment | MySQL Community Edition - Standard (GPL) | | version_compile_machine | x86_64 | | version_compile_os | unknown-linux-gnu | | wait_timeout | 28800 | +---------------------------------+-----------------------------------------------------------------------------+ 210 rows in set (0.00 sec)

    Read the article

  • My PC suddenly doesn't detect the primary drive (SSD)

    - by smoth190
    My computer has been working fine for months, and it worked today, but tonight I went to start it up to find that my OCZ Vertex 2 isn't being found. When I turn on my computer, the loading screen gets stuck at "Detecting IDE drives...". After a while, it keeps going and lists the drives it finds. The first one in the list should be my Vertex 2, but it just says "None". The computer proceeds to get stuck on "Loading operating system...", which is understandable because the drive with the OS is "gone". My first thought was drive failure, but every time drives have crashed on me, they're still detected--they just don't work. This drive is an SSD, it's pretty new, and I had no problems beforehand. I find it hard to believe it failed. I'm sure it's possible, but I hope this isn't the case. There has been nothing strange going on at all with my PC, it's been running perfect until now. I was just about to do my monthly dskchk and defrag today. I popped in my Windows 7 Home Premium disk and booted from it. When I launched the repair tool, it didn't list any operating systems (because the drive is 100% missing...). When I've had disks crash before, it still listed the OS, you just couldn't do anything with it. I tried to restore from an image, but I don't have any of those, either. I opened the command console and listed the drivers with wmic logicaldisk get name. Only C: and D: came up. C: was my 1TB storage driver (luckily, all my stuff is here--only the OS is on the SSD!) and D: was the disk driver. So I still had an MIA drive... The SSD didn't come with any driver disks, so I can't install drivers. If there's a way to do this from a CD I can burn with my other PC, please let me know. What the heck do I do? Although only the OS is on my SSD, a new SSD is expensive. I'll probably also have to buy a new copy of Windows (an upgrade would be nice, though...) because I've found it eats my registration key when my PC crashes (and my thousands of dollars of Adobe programs, I'll be on the phone with tech support for a week to get those keys back). And I'll lose my registry, all my settings, all sorts of other stuff that I'll spend weeks restoring. My computer is a pain in the butt to take out and open up, so if I can't fix it, I'll try fiddling with the plug or putting it into a new computer, but not right now. Any help is greatly appreciated! The day when they make crash-less drives will be the day I live without worry.

    Read the article

  • Gaming blew fuse and causes funny smell: how to overcome?

    - by George Tomlinson
    I've been gaming for a while now. When playing certain games this PC goes into overdrive. The fan/fans start/s to sound like a jet engine it/they get/s so busy. Also I have smelt burning when this has happened. The fuse blew on the 4 socket adapter I was using recently. On the following thread someone said this could be due to the PSU not being strong enough to handle the load, in what it seems could be a related issue someone had, although the person who posted this question did say that blowing a fan on their PC stopped it crashing in that case: http://www.tomshardware.co.uk/answers/id-2047543/gtx-650-overheating-issue.html. This is exactly what they said: Your GPU isn't overheating. 70+ before it would shutdown and cause a restart. Make sure your PSU is strong enough to handle your new system at load and possibly run Memtest to check your RAM (although not BSOD'ing and just shutting down points to the PSU). This (the PSU part) makes more sense to me than it being to do with dust etc, since it seems a more plausible explanation of why the fuse blew. The PC has no problems except when playing certain games: i.e. TERA Rising and WoW with add-ons (I think WoW is ok as long as I don't have more than 1 add-on (Healers Have To Die)). I'm just wondering if anyone knows or can suggest what I might be able to do to be able to play these games without this problem occurring. The PC's spec is this: Display: NVIDIA GeForce GTX 650 8GB RAM (6 available) Processor: AMD FX (tm) - 8120 Eight-Core Processor - 3.1 GHz, 4 Cores, 8 Logical Processors I have read on another post that forcing vsync in the Nvidia Control Panel helped with what seems could be a similar problem, so I plan to see if that solves it, God permitting. EDIT: I tried the Vsync thing, and it seems the situation may have improved, although this may be due to something else: i.e. maybe the PC was working harder yesterday, due to just having downloaded a few things or lots of things running. I'm still noticing the funny smell when playing TERA. It's not so much burning: it's more like glue. The smell might have had a burning element to it in the past, but I think it's always had a glue element. EDIT 2: the PSU is an 'ATX Switching Power Supply', Model E-500ATX. Other info it gives on the PSU is 230V, Current 10A and Frequency 50-60Hz. It also has some other info which I can supply if necessary. Putting the PC plug in the wall socket instead of the power strip seems like it might have reduced the load on the PC quite a bit: I think it sounds less stressed. it has been off for a while whilst I took the side panel off though, so I'll wait to see what happens before getting too excited. EDIT 3: hmm. So here's the latest: just playing TERA. The fan's running quite fast again. Hard to tell whether switching to the wall socket has made a difference in terms of strain on the PC: I don't know if one would expect it to. Still seems like it might have helped though. Oh and there didn't seem to be much dust in the PC, although I didn't disconnect any components. I'm still getting the glue type smell. ASIDE: reminds me of someone on a PC near me at the library once who was actually sniffing glue right there in front of everyone while on the PC and he started talking about how he was sniffing glue. lol. That's no joke. EDIT 4: So the questions now are: Question 1: Is the smell something I should sort out? (If so, how might I do this?) Question 2: is it necessary to take any steps to prevent blowing another fuse (and if so which step/s?).

    Read the article

  • need assistance with my.cnf - 1500% CPU usage

    - by Alan Long
    I'm running into a few issues with our new database server. It is a HP G8 with 2 INTEL XEON E5-2650 processors and 32GB of ram. This server is dedicated as a MySQL server (5.1.69) for our intranet portal. I have been having issues with this server staying alive - I notice high CPU usage during certain times of day (8% ~ 1500%+) and see very low memory usage (7 ~ 15%) based on using the 'top' command. When the CPU usage passes 1000%, that is when the app usually dies. I'm trying to see what I'm doing wrong with the config file, hopefully one of the experts can chime in and let me know what they think. See below for my.cnf file: [mysqld] default-storage-engine=InnoDB datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock #user=mysql large-pages # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 max_connections=275 tmp_table_size=1G key_buffer_size=384M key_buffer=384M thread_cache_size=1024 long_query_time=5 low_priority_updates=1 max_heap_table_size=1G myisam_sort_buffer_size=8M concurrent_insert=2 table_cache=1024 sort_buffer_size=8M read_buffer_size=5M read_rnd_buffer_size=6M join_buffer_size=16M table_definition_cache=6k open_files_limit=8k slow_query_log #skip-name-resolve # Innodb Settings innodb_buffer_pool_size=18G innodb_thread_concurrency=0 innodb_log_file_size=1G innodb_log_buffer_size=16M innodb_flush_log_at_trx_commit=2 innodb_lock_wait_timeout=50 innodb_file_per_table #innodb_buffer_pool_instances=4 #eliminating double buffering innodb_flush_method = O_DIRECT flush_time=86400 innodb_additional_mem_pool_size=40M #innodb_io_capacity = 5000 #innodb_read_io_threads = 64 #innodb_write_io_threads = 64 # increase until threads_created doesnt grow anymore thread_cache=1024 query_cache_type=1 query_cache_limit=4M query_cache_size=256M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 0 wait_timeout = 1800 connect_timeout = 10 interactive_timeout = 60 [mysqldump] max_allowed_packet=32M [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid log-slow-queries=/var/log/mysql/slow-queries.log long_query_time = 1 log-queries-not-using-indexes we connect to one database with 75 tables, the largest table has 1,150,000 entries and the second largest has 128,036 entries. I have also verified that our PHP queries are optimized as best as possible. Reference - MySQLtuner: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.69-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 420M (Tables: 75) [!!] Total fragmented tables: 75 -------- Security Recommendations ------------------------------------------- [!!] User '[email protected]' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 1h 14m 50s (8M q [1K qps], 705 conn, TX: 6B, RX: 892M) [--] Reads / Writes: 68% / 32% [--] Total buffers: 19.7G global + 35.2M per thread (275 max threads) [!!] Maximum possible memory usage: 29.1G (93% of installed RAM) [OK] Slow queries: 0% (472/8M) [OK] Highest usage of available connections: 66% (183/275) [OK] Key buffer size / total MyISAM indexes: 384.0M/91.0K [OK] Key buffer hit rate: 100.0% (173 cached / 0 reads) [OK] Query cache efficiency: 96.2% (7M cached / 7M selects) [!!] Query cache prunes per day: 553614 [OK] Sorts requiring temporary tables: 0% (3 temp sorts / 1K sorts) [!!] Temporary tables created on disk: 49% (3K on disk / 7K total) [OK] Thread cache hit rate: 74% (183 created / 705 connections) [OK] Table cache hit rate: 97% (231 open / 238 opened) [OK] Open file limit used: 0% (17/8K) [OK] Table locks acquired immediately: 100% (432K immediate / 432K locks) [OK] InnoDB data size / buffer pool: 420.9M/18.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Temporary table size is already large - reduce result set size Reduce your SELECT DISTINCT queries without LIMIT clauses Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 256M) [see warning above] Thanks in advanced for your help!

    Read the article

< Previous Page | 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797  | Next Page >