Search Results

Search found 8897 results on 356 pages for 'hit detect'.

Page 180/356 | < Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >

• New power supply, now computer doesn't recognise hard drive?

  - by Mike

  Ok, I bought a new power supply, because my old one was too damn loud. I hooked it up to my PC, turned it on, everything is looking fine, start up detects my DVD drive, 2 hard disks.. then I get the message "BOOT FAILURE INSERT SYSTEM DISK". Now I've seen some other people talk about going into BIOS and changing the start up to the HDD and not the CD.. well I've done that and it doesn't help. If I let windows load up and it asks me to which partition I wish to install windows, no partition is present. It's as if after the initial start up the drives arn't being found. I plugged my old (but loud) PSU back in, connected up all the cables, and it works perfectly. Why does the new PSU not detect my HDD's after the first BIOS screen start up? Any ideas? :)

  Read the article

• Windows 7, how to get unlock (Press Ctrl+Alt+del) prompt on all monitors?

  - by Zugwalt

  I have a laptop that I keep shut in a docking station as I have two screens connected to the laptop and it cannot display to both of those AND its own screen. However, when my computer locks by itself (Not when I lock it using Ctrl+Alt+Del) the login prompt is ONLY on it screen (at least its there when I open it up) and my primary external monitor is off and my other one is all black. This means to log in I have to hit Ctrl+Alt+Del and blindly enter my password--which I don't mind too much, but would prefer if I could actually see the unlock/login prompt instead of typing on a black screen. Any way to have it show the login prompt on all monitors?

  Read the article

• Remote access and local access same hostname

  - by cpf

  Hi serverfault, I have a server in a clients network, seperated from theirs with a router/firewall, the intention is to have this server available through one hostname (example.com) My idea is to have (at least) a DNS server in the outside, to have outside (out of the clients' network) access the internal server. The problem would at that point be the internal client (PC A) My question: What would I have to do to make something like this work? Is it even possible or already done? The goal is to not have to change anything on either PC A or PC B, while both should access the same "internal server" while surfing to "example.com" Perhaps adding logic to the DNS server would work (Detect the external IP of internal client [PC A] is the same as the IP for example.com - Give the local IP as reply?) Anyhow: Thanks for helping me think on this!

  Read the article

• Run Dialog: Tab Key dont complete commands

  - by Gilney

  I like to use the Tab key to complete/skip commands/links in Shells/Browsers when typing. But when I hit the tab key in "Run Dialog" causes focus leave Text box, so i'm forced to leave home keys to use arrow keys. Is there a way change this behavior? Edit: I found here a flag that enables autocomplete in Run Dialog. This doesn't solve the question, but it helps when the command you want is the first option listed, because you just press enter instead of moving to arrow key and select the command. In my case this solves about 80% of cases.

  Read the article

• Route global shortcuts to pages opened in Firefox

  - by zamza

  I like listening to music online on sites like stereomood.com. There is a major problem, however. I can not control the player with my keyboard. And even with a mouse - when I want to play/pause I must activate firefox window, select the tab where music plays and hit play/pause button manually - this is a pain, especially when you play a fullscreen game that can not minimize itself. Thus said, global keyboard shortcuts would be a perfect solution. I understand that different online media players have different controls and each site must be configured individually (like, select button with id 'play' and press it), but I believe that can be done in principle. I also guess that such tricks are impossible without some third-party native app which captures shortcuts and routes them to Firefox window. So, any solutions? Maybe some AutoHotkey hacks or similar.

  Read the article

• Mavericks: Safari does not login in into web services

  - by Roberto

  Since when I upgraded ML to Mavericks Safari is no longer able to log me into Facebook. When I go to the login page it suggests me the correct credentials, I hit the Login button, the page refreshes but nothing happens, like if the credentials where empty. Firefox works perfectly, I even logged out and back in to make sure the credentials are the same that Safari suggests, and so they are. Needless to say for a different user on the same Mavericks Safari logs in correctly. The same happens with most web pages that need a login, web mails for instances, I have tow accounts on different webmail providers and none of them works. Of course using the same mail services with POP3 works fine. Even on this very site I cannot post a thing with Safari, I'm going to switch to Firefox to be able to post this question. Again, Firefox or a different user are OK. Do you have any idea/suggestion?

  Read the article

• Linux mdadm software RAID 6 - does it support bit corruption recovery?

  - by user101203

  Wikipedia says "RAID 2 is the only standard RAID level, other than some implementations of RAID 6, which can automatically recover accurate data from single-bit corruption in data." Does anyone know if the RAID 6 mdadm implementation in Linux is one such implementation that can automatically detect and recover from single-bit data corruption. This pertains to CentOS / Red Hat 6 if those are different from other versions. I tried searching online but didn't have much luck. With SATA error rates being 1 in 1E14 bits, and a 2TB SATA disk containing 1.6E13 bits, this is especially relevant to preventing data corruption. Thanks!

  Read the article

• iptables: How to create a rule for a single website that does not apply to other websites?

  - by Kris

  Virtual Dedicated Server hosts 10 websites. 1 firewall made with iptables If one of those 10 websites gets hit by too many ping requests coming from one IP address, how do I limit or drop it without dropping it for the other 9 websites? Do I create a firewall for every website ? If so, how? Or is it better to change my rules? If so, how? Thank you. Original question was posted here iptables: what's best practice when there're several websites but you want to use a rule for a single website? but it was too vague. Let me know if more info is needed.

  Read the article

• VM VirtualBox, Ubuntu 9.10: USB memory stick and SD card not detected...

  - by vikramtheone

  Hello Guys, I have installed Ubuntu9.10 on VM VirtualBox, on my HP laptop. My laptop has several USB ports and also a SD card port. Unfortunately, I'm unable to access both, my pen-drive on the USB port and my 8GB SD card inserted in the SD Card port. Can anyone suggest me what I should do for my Ubuntu to detect both of them? I have installed all latest updates on Ubuntu. I'm able to use my USB mouse. Thank you Vikram

  Read the article

• ESXI with non standard hardware HDD issues

  - by Hurricanepkt

  I have 3 very underutilized servers that I am condensing to one of those shuttle PC's with VMWare ESXi The HDD seems to be the bottle neck right now (the light is almost always pure solid) right now I have a single 1TB Seagate 7200.11 connected by SATA. VMWare ESXi cannot detect it when running in AHCI mode, but does when running in IDE mode. I have read that IDE mode can give a 5% performance hit which might give me enough breathing room. However, I am open to setting up an external eSATA or some sort of raid to give me more than just the 5%. I am just weary of sinking some money into a bit of hardware without knowledge of whether it will work. Does anyone know of resources or procedures of how to get this working.

  Read the article

• How to block this URL pattern in Varnish VCL?

  - by iTech

  My website is getting badly hit by spambots and scrappers, I am using Cloudflare but the problem still remains there. The problem is spambots accessing non-existing urls causing a lot of load to my drupal backend which goes all the way and bootstraps db just to serve a 404 error doc. I cant simply dish out non-drupal 404's for all page not found errors, as I need to have drupal catch them. Since, varnish is in front it can check if the bot is acting nice and asking for valid url - if not it servers them a 404 or 403. These bots are causing errors using this pattern : http://www.megaleecher.net/http:/www.megaleecher.net/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_Storage Now, pls. suggest a regex varnbisg VCL directive which catches this URL pattern and serves a 404 error from varnish, preventing it from reaching apache/drupal ?

  Read the article

• Empty AAAA DNS Record with long TTL?

  - by Joel K

  I pay for a DNS service based on queries per second. We are not using IPv6, but a large number of queries (that I pay for) are coming in for AAAA records. I understand that most DNS stacks will now ask for A and AAAAs at the same time, and that I can't change that. What I /would/ like to do is put something in the AAAA records with a long TTL. (decreasing my hit rate) Is there anything I can put? Null? The equivalent IPv4 Address? Any guidance would be appreciated.

  Read the article

• howt setup remote access into computer behind 2 routers?

  - by Steve Wasiura

  I can setup remote access to a pc behind a single router/firewall by using NAT and Port Forwarding, simples! But there is a customer that shares an internet connection with another office, and they are behind a second router firewall. I drawed a picture with my crayons but I can't attach it because I'm a new account on SF. see it here: http://i.imgur.com/b3FDx.png So how would I setup remote access to the pc that is beind the second firewall? It must be something about static routes, i.e. if I hit the wan ip on port 4905 I want it to forward it to 10.0.0.30 by going through 192.168.1.10 so a route statement like for all requests to 10.0.0.30, use 192.168.1.10 ? and ass u me router 2 has a static gateway ip of 192.168.1.10 and need a standard NAT on router 2 to point port 4905 to 10.0.0.30 is this the right way, any tips? both routers are netgear consumer equipment. thanks

  Read the article

• How to monitor Windows Server events with Centreon Nagios

  - by Miss M

  I want to monitor events on a Windows Exchange Server (Windows 2008 R2) and have installed NSclient ++ so I can use Centreon Nagios to monitor it. I did a bit of research and came across this question that I found somewhat helpful: How to monitor Windows host with Nagios? Nick Kavadias gave a good answer but it did not provide an explanation on how to configure the Nagios config file in such a way that it would monitor a specific service on the server. So, how do I set up a service in Nagios in such a way that it will detect when a windows event occurs on a server?

  Read the article

• Duplication of Windows 7 Backup

  - by Steven Pickles

  I use the built in backup utility for Windows 7 because it's automated and flexible enough to allow me to schedule a daily shadow copy backup of particular files and folders directly to a separate internal RAID 0 array (2 x 1TB). It's also lightweight and stays out of the way. For off-site backup purposes, each week I copy the contents of the internal backup from the RAID 0 array to an external 1 TB drive. I then store move this drive to a different building. The copy from the internal backup to the external backup typically works like this: mount and erase contents of external drive highlight "file" on internal drive, hit CTRL+C CTRL+V on root directory of external drive Is there a better way to synchronize? Microsoft's SyncToy application does a pitiful job, and often leaves the folders not truly synchronized... which completely defeats the ability to use the backup's restore feature.

  Read the article

• Remove Legal Notice IN Registry

  - by Jerry

  I have a very slow laptop that I need to reboot 3 times a day. It is connected to a Windows domain. I have managed to get it to auto-logon, but I still get prompted to hit ok after reading a legal notice. I have cleaned out [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System] and exported it. I import it every 10 minutes via a script. How can I permanently remove the legal notice. A new laptop is not an option right now.

  Read the article

• Running php and java in parallel on the same server

  - by manni

  I have got a java server from Rackspace. and I am already running a java application on the server. Now I want to run a php application on the same server. What should I do? When I asked Rackspace people, they said, apache is already installed on the server so I can run the php on it. I have also tried installing php on the server and then copied my php files in var/www/xxx but when I hit the url it is saying giving the page not found error. They have given me the ssh server root username and password. Thanks in advance.

  Read the article

• Vlan Tagging at Access Port in Switch

  - by singh

  I'm Confused from the fact that Vlan tagging is done at access port and trunk port always gets tagged packets (until its case of native vlan).But I still believe in other fact which says tagging happen only when a frame hit the trunk port which means trunk port gets untagged frame and tagging is not possible at access port. Would like to know where actually this tagging happens ? and also which command we can use to encapsulate 802.1q protocol to access port ? The way we do at trunk port is switchport trunk encapsulation dot1q Is the above command applicable for access mode also?

  Read the article

• Motherboard or Processor Problem

  - by bradlis7

  My computer is broken, but I'm having trouble narrowing down the issue. I replaced the power supply, because I assumed that was the issue, but it has the same problem. The issue started with my computer starting the fans and running, but it didn't get to the BIOS screen for about 10 seconds. Now it refuses to do anything when the power button is pressed, except when I turn off the machine and take the processor out for 10-20 seconds, then put it back in, I came hit the power button immediately, and the fans start for 1/2 second, and quit. Does this sound like a is a processor or motherboard issue? I removed all components, so I know that the issue is with one of these two things.

  Read the article

• Slot load DVD burner options for standard desktop case

  - by Michael Kohne

  I need a new DVD burner (internal) for my father-in-law's computer. He's apparently broken the current one - he forgot to push the tray back in after doing something and hit it with his chair. Given this, I'd like to get him a slot-loading DVD burner, so as to avoid the problem entirely. I need an internal device, and I'll be mounting in a 5 1/4" bay. He doesn't need any super-spec device - as long as it can read/write all the standard formats, it's good. I see a few options at newegg.com, but they all have mixed reviews. Are there any out there that are generally seen as reliable? How does one go about mounting slimline devices in a standard 5 1/4" bay? Is there a standard faceplate kit for that?

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook.

  Read the article

• Wierd Windows File Share Behavior

  - by CT

  Scratching my head awhile on this. I'm on a Vista client trying to access a file share running on a Windows Server 2008 R2 box. Windows Active Directory Domain. The shares I am trying to access: \\Server1\FileShare1\Folder1\foo and \\Server1\FileShare1\Folder1\bar The client does not have any permissions at Folder1. The client has read permissions at folders foo and bar. In this example I can access \Server1\FileShare1\Folder1\foo but I get the following error when I try to access \Server1\FileShare1\Folder1\bar: "Network Error: Windows cannot access \Server1\FileShare1\Folder1\bar. Check the spelling of the name. Otherwise, there might be a problem with your network. To try to identify and resolve network problems, click Diagnose" I hit Diagnose. It returns with "Windows checked the path and '\Server1\FileShare1' is correct but 'Folder1' could not be found." What is going on? It finds Folder1 fine when going to \Server1\FileShare1\Folder1\foo.

  Read the article

• Shut down by pressing the power button twice

  - by iHarry

  I have set my laptop's power button to shut down the computer when it is pressed (Windows 7 x86). But I often hit the button accidentally, and it's a rare case that I'm able to actually prevent it from shutting down. I don't want to disable it though. Is there a way so that I get a confirmation whether I really want to shut down the computer (just like in Mac OS X Lion, where a confirmation appears when the power button is pressed)?. Is there some way to bring the same to Windows 7 (and 8)?

  Read the article

• Send request body data when running siege

  - by qui

  I am trying to use the command line utility Siege to load test a service. The service recieves json in the request body via a POST. I have a file called example-data.json with the json inside. I will eventually turn this into a tiny service which creates random json for testing, but this should do for now I have another file called hit-qa.siege with http://www.qa-url.com POST < example-data.json and i try and run siege -c10 -d1 -r1 -f ops/perf/hammer-dev.siege When I check the logs of the service, it is not recieving anything in the request body. My googles have been fruitless, does anyone know how to accomplish this?

  Read the article

• Removing 'bundled' software to make a slow laptop faster?

  - by spdegabrielle

  My brother-in-law has a cheap HP laptop used by his kids for schoolwork. It had got into a bit of a state and was running slowly with some dubious software. I removed a bunch of stuff that had been installed, that was obviously not required (three different driver scanners!), had been downloaded in error or looked like malware. I also disabled as many 'start on login' apps as I could and removed AVG replacing it with MSE. (AVG is uninstalled and replaced with MSE after failing to detect malware) What remains is a significant quantity of bundled HP and 'nero backup' software, including a HP restore utility (apparently something like the osx hidden partition restore), the trackpad driver. is there anything else I can do to breath a little more life into the old 'celeron' laptop? Should I bit the bullet and just put win8 on it? Will the trackpad still work?

  Read the article

< Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >