Search Results

Search found 32102 results on 1285 pages for 'local network'.

Page 180/1285 | < Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >

  • Windows VPN always disconnects after < 3 minutes, only from my network

    - by hemp
    First, this problem has existed for almost two years. Until serverfault was born, I pretty much gave up on solving it - but now, hope is reborn! I've set up a Windows 2003 server as a domain controller and VPN server at a remote office. I am able to connect to and work over the VPN from every windows client I've tried, including XP, Vista, and Windows 7 without issue, from at least five different networks (corporate and home, domain and non.) It works fine from all of them. However, whenever I connect from clients on my home network, the connection drops (silently) after 3 minutes or less. After a short while, it will eventually tell me the connection has dropped and attempt to redial/reconnect (if I've configured the client that way.) If I reconnect, the connection will re-establish and appear to work correctly, but again will silently drop, this time after a seemingly shorter time period. These are not intermittent drops. It happens every single time, in exactly the same way. The only variable is how long the connection survives. It doesn't matter what type of traffic I send. I can sit idle, send continuous pings, RDP, transfer files, all of that at once - it makes no difference. The result is always the same. Connected for a few minutes, then silent death. Since I doubt anyone has experienced this exact situation, what steps can I take to troubleshoot my evanescing VPN?

    Read the article

  • OpenVPN bridge network from routed clients

    - by gphilip
    I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

    Read the article

  • Can I share my cable internet connection through my ADSL wireless router?

    - by Roaders
    Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

    Read the article

  • Setting up home DNS with Ubuntu Server

    - by Zeophlite
    I have a webserver (with static IP 192.168.1.5), and I want to have my machines on my local network to be able to access it without modifying /etc/hosts (or equivalent for Windows/OSX). My router has Primary DNS server 192.168.1.5 Secondary DNS server 8.8.8.8 (Google's public DNS). Nginx is set up to server websites externally as *.example.com Internally, I want *.example.local to point to the server. My webserver has BIND9 installed, but I'm unsure of the settings. I've been through various contradicting tutorials, and so most of my settings have been clobbered. I've stripped out the lines which I'm confused about. The tutorials I looked at are http://tech.surveypoint.com/blog/installing-a-local-dns-server-behind-a-hardware-router/ and http://ubuntuforums.org/showthread.php?t=236093 . They mostly differ on what should be put in /etc/bind/zones/db.example.local and /etc/bind/zones/db.192, so I've left the conflicting lines out below. Can someone suggest what the correct lines are to give my above behaviour (namely *.example.local pointing to 192.168.1.5)? /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.5 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.254 /etc/hostname avalon /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN /etc/bind/named.conf.options options { directory "/var/cache/bind"; forwarders { 8.8.8.8; 8.8.4.4; }; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local zone "example.local" { type master; file "/etc/bind/zones/db.example.local"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.192"; }; /etc/bind/zones/db.example.local $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 5 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL /etc/bind/zones/db.192 $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 4 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; What do I need to add to the above files so that on a laptop on the internal network, I can type in webapp.example.local, and be served by my webserver? EDIT I made several changes to the above files on the webserver. /etc/network/interfaces (end of file) dns-nameservers 127.0.0.1 dns-search example.local /etc/bind/zones/db.example.local (end of file) @ IN NS avalon.example.local. @ IN A 192.168.1.5 avalon IN A 192.168.1.5 webapp IN A 192.168.1.5 www IN CNAME 192.168.1.5 /etc/bind/zones/db.192 (end of file) IN NS avalon.example.local. 73 IN PTR avalon.example.local. As a side note, my spare Win7 machine was able to connect directly to webapp.example.local, but for a Ubuntu 13.10 machine, I had to make the following changes as well (not on the webserver, but on a separate machine): /etc/nsswitch.conf before hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 after hosts: files dns /etc/NetworkManager/NetworkManager.conf before dns=dnsmasq after #dns=dnsmasq The issue remains that its not wildcard DNS, and so I have to add entries to /etc/bind/zones/db.example.local for webapp1, webapp2, ...

    Read the article

  • using ubuntu connect to server to mount windows share

    - by myforwik
    I have a system with Ubuntu 9.10 installed. I can connect to remote windows shares by using the "connect to server" under "places" menu. I can't figure out where these mount in the file system. Is it possible to mount it in the file system. And I can't install smbfs or anything else. I need to use only what comes on the live CD, as there is no internet connection and no way to get in packages.

    Read the article

  • Trouble getting started with the STEALTH monitoring package

    - by dlanced
    Is anyone here familiar with the Linux-based STEALTH package (for monitoring FS integrity of client systems)? I'm trying to get started with a very simple configuration, but I'm running into trouble (this is running under Ubuntu 14.04): Config line `USE BASE/root/stealth/10.0.0.79' invalid STEALTH (2.11.02) started at Fri, 30 May 2014 15:25:00 +0000 Program terminated due to non-zero exit value for -type f -exec /usr/bin/sha1sum {} \; (EOC Fri May 30 15:25:00 2014 127) Stealth is creating a binary tmp file in the Stealth server root and generating a "report" file in the start directory, but not much else. Regarding the "USE BASE...invalid" error, and just to be sure, I manually created the directories in /root, but it didn't help. And, by the way, I am running stealth with sudo. Everything seems to be configured correctly: I'm able to ssh into root@client from the stealth machine without a password Here's my "policy" file (I've removed the email directives just for simplicity): DEFINE SSHCMD /usr/bin/ssh [email protected] -T -q exec /bin/bash --noprofile DEFINE EXECSHA1 -xdev -perm +u+s,g+s ( -user root -or -group root ) \ -type f -exec /usr/bin/sha1sum {} \; USE BASE/root/stealth/10.0.0.79 USE SSH ${SSHCMD} USE DD /bin/dd USE DIFF /usr/bin/diff USE PIDFILE /var/run/stealth- USE REPORT report USE SH /bin/sh GET /usr/bin/sha1sum /root/tmp LABEL \nchecking the client's /usr/bin/find program CHECK LOG = remote/binfind /usr/bin/sha1sum /usr/bin/find LABEL \nsuid/sgid/executable files uid or gid root on the / partition CHECK LOG = remote/setuidgid /usr/bin/find / ${EXECSHA1} LABEL \nconfiguration files under /etc CHECK LOG = remote/etcfiles \ /usr/bin/find /etc -type f -not -perm /6111 \ -not -regex "/etc/(adjtime\|mtab)"\ -exec /usr/bin/sha1sum {} \; Any ideas? Thanks,

    Read the article

  • Using runit and monit to run / monitor services

    - by murtaza52
    I am configuring some services to run on Ubuntu server. I was going through the link below where they use runit to run the services and monit to monitor the services - http://rubyworks.rubyforge.org/manual/monit.html http://rubyworks.rubyforge.org/manual/runit.html 1) The services are all started through monit. 2) Monit inturn starts them using runit. What is the advantage of using the above setup, where the services are run using runit via Monit. Why use runit in the middle, instead of directly starting them with monit?

    Read the article

  • Run command before and after printing with CUPS?

    - by leto
    Hello, this is a home setup. A central printer server (Linux) manages the queue, a HP 2430DTN is attached to it via 100Mbit/sec Ethernet. The printer is hooked up to a managable power source. A shell script watches the queue on the server (lpstat -o) and turn on the printer when there is a job. If the queue is empty for 10 minutes it turns the printer off. Now this setup messes up, stops the printer etc. after a couple of weeks and is in general "not so reliable". I now know how to change the stop-printer thing, but: Is there a way to run my turn printer on script and turn printer off script directly from cups without watching the queue? That would be so cool!

    Read the article

  • Network Security Device/Software

    - by Campo
    We currently run Symantec Antivirus Corporate 10.2. The software is really easy to manage on a network but the actual virus detection isn't bad but the malware detection is crap. We recently were infected with a email bot that got us put on some block lists. This has been resolved. I cannot have that happen again. I would like to find a program as easy to manage as symantec that I can install on all the user's workstations as well as the servers. We run a windows 2003 domain. We have a couple 2008 test servers in the environment. Most of the workstations are xp though I am using windows 7 and symantect is not compatible with this OS... So we need a solution that would cover all those operating systems. If it could be installed on macs too that would be a bonus though not necessary at all. This software must detect: Viruses AND Malware I am looking for something that combines the features in anti-malware programs like malwarebytes or spybot with an antivirus program like symantec or AVG. Alternatively if there is a piece of hardware that is a firewall, router, and packet inspection for virus/spam that would be the most ideal solution. I then could supplement with a piece of software that could pickup what the hardware misses. Thank you for your suggestions.

    Read the article

  • Why does a Remote Desktop Redirected Printer Doc appear every time I connect to Windows Server 2003 SBS?

    - by Jim Dagg
    I've run into a weird, persistent issue regarding a remote desktop connection. Every time I successfully log into a server running Windows Server 2003 SBS, without taking any further action, after a few seconds a print job spontaneously appears on my machine, titled "Remote Desktop Redirected Printer Doc". The document is 4K, datatype RAW, processor "WinPrint". I've heard of people running into this issue before, but can't seem to hunt down a coherent solution. It's a minor annoyance, but I get annoyed when Windows complains about a print job that, as far as I know, came from nowhere. Any thoughts on why this would occur and how I could prevent it from happening?

    Read the article

  • hardware: delay and distinct 'click' before hard drive access

    - by matt lohkamp
    I have a windows 7 box stashed away in my closet, containing (among other things) 2 big HDDs linked together as a mirrored volume - basically a super lazy NAS / media server. I've noticed that when that drive is accessed (whether locally, on the machine itself, or remotely, from another computer, or my xbox, for example) there's a noticeable pause, and then from the computer itself, a 'click!' noise, after which the drive is accessed; e.g. open \\computername\shared\, wait 2 seconds, hear 'click!' and then see files appear in windows explorer. Any ideas? Otherwise the drive preforms normally - is it a windows thing? a HDD-about-to-die thing? Or a "yeah that always happens, you've just never noticed it before" thing?

    Read the article

  • How to monitor bandwidth use of each device on wifi network

    - by GWLlosa
    I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

    Read the article

  • Cannot access shares via \\servername but \\ip works

    - by Jeff
    To set up the scenario: One of our techs set one of the domain controllers to use Microsoft time. The time IS correct (including Time Zone) and DOES match the other domain controller's time; it was previously incorrect, however. Since the change, no users can connect via \\servername\share or \\servername.domainname.com but \\ip\share works fine. I cannot even access it from the other domain controller with which I know both have the same time. The servername DOES resolve to the correct IP address. Also, strangely enough, \\domainname.com works as well which resolves to the same server. Finally Everything that I have tried does resolve to the same, correct IP address. The error is: login failure: The target account name is incorrect. I believe it is time related but since the times are correct and match I'm not sure. Anyone know what might cause this?

    Read the article

  • Mapped network drive missing from My Computer and Explorer

    - by matt wilkie
    On a Windows XP Pro SP3 machine one network drive refuses to show up in My Computer or Explorer. The missing drive letter is G:, if that matters. Other mappings work fine. Other profiles one the same machine have no problem mapping G:. I can access the G: just fine typing it into the address bar or in CMD shell. I've used TweakUI to toggle hide/show G: with no difference. TweakUI says G: should be visible. I've logged off,on between toggles to make sure the settings are taking effect. I've looked at reg key [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer] and made sure it's zero'd. [insert ref link here] We've limped along with this broken setup for some time, just working around it, but some applications do not allow typing in a path when choosing a place to save files and it's reached the point where it's intolerable. So, anyone have any idea why XP won't show this drive letter? or how to fix it?

    Read the article

  • How to access XAMPP virtual hosts from iPad on local network?

    - by martin's
    Using XAMPP on one machine. Multiple virtual hosts defined. One per project. Format is .local For example: apple.local microsoft.local client-site.local our-own-internal-site.local All works perfectly from that one machine. I now want to have other systems within the network access the various sites. The main reason for wanting to do this is to be able to test site functionality and layout from mobile devices without having to upload partial work to public servers. I can access the main XAMPP default site by simply entering the IP address of the XAMPP machine in, say, Safari on an iPad. However, there is no way to reach .local that I can see. Would this entail setting up a DNS server within the network? We have a mixture of Windows and Mac machines. No Linux. The XAMPP machine is Vista 64. I don't want real external internet access to be affected in any way, just ".local" pointed to the XAMPP machine if that makes sense.

    Read the article

  • port forwarding/network settings preventing from game hosting

    - by Xitcod13
    I asked where to post this question on stackoverflow meta and they directed me here. Im on wireless connection and I want to host games in StarCraft: Brood War and i've been looking everywhere on how to accomplish that. My internet is amazingly fast so its not an internet problem (and when i play other peoples games dont experience lag) I found out that i need to have a static IP but I have already checked that i do (i downloaded a program to make my id static and it already was; The program asked for which router I used So i think it checked the router settings already) I found out that i need to allow Sc access through the firewall which i already did (i have zone-alarm but I allowed it everything possible except receiving emails lol) I have recently noticed that few people actually can join my games but most of them cannot. I dont know whats going on here. I really want to be able to host games overall how do I go about checking what is wrong with the network. Update: Alright I figured out what i did wrong in the first part I did not actually set up forwarding on the router -.- I have tried to fix my mistake. I went to forwarding options in my router (as this guide for my specific router suggests) but when i click ok I get a message incorrect ip address. 192.168.1.1 is my routers address. The default address that appears there is 192.168.1 (blank) I have set it to my computers current Ip4 adress which 192.168.1.23 I hope this works If so i will post it as an answer and mark it.

    Read the article

  • users connecting to remote desktop to use software

    - by Jordan
    Im an IT assistant at a CNC milling company and we use a program called made2manage. Its an ERP (enterprise resource management) software. Each license is something like 5k and instead of giving each employee there own copy of the software he has everyone that uses the program connect to a server that has a copy of m2m on it. Its slow when there are a bunch of people connected to it. But I guess they dont want to buy more licenses. Is there a better way to do something like this? How bad of a practice is this?

    Read the article

  • Sharing internet through a wireless ad-hoc in Windows 7

    - by vzait
    I'm actually requesting a workaround to share a PPoE wired Internet connection between two laptops using wireless. I've tried sharing it the usual way... New Ad-hoc = Click turn On sharing = etc. I've tried changing all the settings I could find related to the two networks on both machines. Conclusion: Sometimes it works, sometimes it doesn't. Is it really buggy, or are my hands growing from the wrong place? I'm almost sure I'm not the only one having this kind of problem. What is the easiest/correct workaround ?

    Read the article

  • How to logon to a non-domain computer from one in a domain

    - by Svish
    I've met a rather annoying problem that should be very simple, but I can't seem to figure it out. I have a work laptop that is part of a domain, so my username is foobar\bob. I also have my home computer with no domain, just the username bob. I'm trying to connect to a share on my home computer from my work computer. It's asking me for my username and password, which is bob, but when I type in bob it assumes I mean foobar\bob, which of course doesn't work. I've tried to use hostname\bob, but that doesn't seem to work either... What can I do here? Both computers are running Windows 7.

    Read the article

  • What software is available to keep track of hundreds of servers?

    - by djangofan
    What good software is available (free or not free) to help me keep track of information relating to hundreds of servers, their relationships to each other (parent/child, category, type), and information on connecting to them, as well as possibly showing a picture or grid of some kind that allows me to report these relationships and key information to my supervisor. I am trying to avoid the "spreadsheet solution" or "visio solution" because I want to share this information and make changes with other persons in my server team. In other words, the solution I am looking for is a cross between a spreadsheet solution and a visio solution, providing both graphing and configuration information WITHOUT monitoring, and in a consistent format.

    Read the article

  • Network Sharing Issues

    - by Mark Kramer
    I have two computers I want to have on a network share together (so the laptop can print through the desktop's printer). These are both connected to the same router. (One wired and one wireless) And they both have the same workgroup name. However, when I type "net view" in the command prompt, the only computer that shows up is the computer I type the command into. How do I get these computers to be shared with each other? Update: The tower is running Windows XP, the Laptop is running Windows 7. I have disabled the Firewall on both until I get this set up. Update 2: Typing the command net view on my desktop is acting very strangely. Noe sometimes it only shows itself on the list of computers, sometimes it shows itself and the laptop and sometimes it doesn't work at all and displays system error 6118. I typed net view into the command prompt on the Windows 7 laptop and both computers showed up, so I went to connect to the desktop from the laptop and it said the dekptop could not be found, even though it is showing up int he list of shared computers. Here are supporting pictures (these are coming from the laptop)

    Read the article

  • ubuntu connect to server -> permantely mount?

    - by myforwik
    I have a system with Ubuntu 9.10 installed. I can connect to remote windows shares by using the "connect to server" under "places" menu. I can't figure out where these mount in the file system. And how can I get this to mount automatically on startup? And I can't install smbfs or anything else. I need to use only what comes on the live CD, as there is no internet connection and no way to get in packages.

    Read the article

  • Common filesystem for servers behind a rackspace load balancer

    - by thanos panousis
    Our PHP application consists of a single web server that will receive files from clients and perform a CPU-intensive analysis on them. Right now, analysis of a single user upload can take 3sec to conclude and take 100% CPU. This makes our system capacity amount to 1/3 requests per second. My team's requirement is to increase capacity without a lot of code reengineering. A possible solution would be to set up a load balancer in front of multiple servers running the same app, connecting to a common DB. The problem is that the analysis outputs files on disk. A load balancer would increase capacity, but then files won't be available between servers so consequent client requests may fail. We are hosted on Rackspace, is there a way to configure some sort of "common" storage for all servers, without having to rewrite our file persistance code? Current code relies on simple fopens etc. What are our options?

    Read the article

  • windows xp command prompt remote

    - by user19810
    I was wondering if it was possible to have remote access to a command prompt on a windows xp machine, like using remote desktop services, only with the command prompt. I'm programming a java application, and having a full remote desktop service is a kind of a system hog. Also, the system I am using to access windows remotely is ubuntu. Thanks.

    Read the article

< Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >