Search Results

Search found 6339 results on 254 pages for 'josh 24 2'.

Page 184/254 | < Previous Page | 180 181 182 183 184 185 186 187 188 189 190 191  | Next Page >

• OpenVPN access to a private network

  - by Gior312

  There are many similar topics about my issue, however I cannot figure out a solution for myself. There are three hosts. A without a routable address but with an Internet access. Server S with a routable Internet address and host B behind NAT in a private network. What I've managed to do is a OpenVPN connection between A and B via S. Everything works fine so far according to this manual VPN Setup What I want to do is to connect A to Bs private network 10.A.B.x I tried this manual but had no luck. So A has a vpn address 10.9.0.10, B's vpn address is 10.9.0.6 and B's private network is 10.20.20.0/24. When at the Server I try to make a route to Bs private network like this sudo route add 10.20.20.0 netmask 255.255.255.0 gw 10.9.0.6 dev tun0 it says "route: netmask 000000ff doesn't make sense with host route" but I don't know how to tell Server to look for a private network in a different way. Do you know how can I make it right ?

  Read the article

• Configure linux machine as bridge/switch and end device

  - by leemes

  At my home, I have two desktop PCs in two rooms. The router / DSL modem is in one of these rooms. Now I want to configure a home server (having 2 LAN ports, running 24/7) in the corridor between the two rooms, using only one LAN cable at each door. This gives me the following physical configuration: (door) (door) .----/-/----. .-----/-/----------._ FritzBox | | | .----´´ DSL Router PC1 Server | PC2 As just said, the server has 2 network interfaces and is running Ubuntu. What I need now is a network configuration which enables both the server and PC1 to connect to the router. I think the server needs to serve as a bridge or switch. Currently, all computers are configured having static IP addresses. If I'm understanding it correctly, a bridge / switch doesn't have its own IP address, but as the server needs to be configured as an own end device, it needs to have one. My first question is, do I have to configure both interfaces separately, giving both the same static IP address? My next question is, how do I bridge the two physical networks into one? I have basic understanding (but am always confused again and again) of bridges and switches, but I don't know how to configure it in software. I only know that it's possible to do so :) The third question is: Is it possible to configure this in a way that network packets from/to PC1 to/from the router only go through hardware or only consume low CPU in the server? Can you help me? Thanks in advance!

  Read the article

• Have servers behind OpenVPN subnet reach connecting clients

  - by imaginative

  I am trying to find some relevant documentation or what directives I need in either the OpenVPN server configuration or client configuration to accommodate for this use case. I have an OpenVPN server that clients connect to. The OpenVPN server can communicate directly with any of the clients already, this is not an issue. The client is able to reach any machine on the private subnet where OpenVPN resides, this is also not an issue. My issue is that the reverse is currently not possible - I have servers on the same subnet as the OpenVPN box that cannot reach any of the connecting clients. I'd like to be able to SSH to them and more, the same way the client can reach the servers behind the OpenVPN subnet. What do I need to do to make this possible? I already have masquerading rules set on the OpenVPN box: iptables -t nat -A POSTROUTING -s 192.168.50.0/24 -o eth0 -j MASQUERADE IP Forwarding is enabled: echo 1 >/proc/sys/net/ipv4/ip_forward I added a route on the server behind the private subnet to be aware of the route: 192.168.50.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 What am I missing?

  Read the article

• I have a perl script that is supposed to run indefinitely. It's being killed... how do I determine who or what kills it?

  - by John O

  I run the perl script in screen (I can log in and check debug output). Nothing in the logic of the script should be capable of killing it quite this dead. I'm one of only two people with access to the server, and the other guy swears that it isn't him (and we both have quite a bit of money riding on it continuing to run without a hitch). I have no reason to believe that some hacker has managed to get a shell or anything like that. I have very little reason to suspect the admins of the host operation (bandwidth/cpu-wise, this script is pretty lightweight). Screen continues to run, but at the end of the output of the perl script I see "Killed" and it has dropped back to a prompt. How do I go about testing what is whacking the damn thing? I've checked crontab, nothing in there that would kill random/non-random processes. Nothing in any of the log files gives any hint. It will run from 2 to 8 hours, it would seem (and on my mac at home, it will run well over 24 hours without a problem). The server is running Ubuntu version something or other, I can look that up if it matters.

  Read the article

• Nginx + Apache + Wordpress redirects to localhost/127.0.0.1

  - by jcrcj

  Anyone know how to fix an issue with Nginx + Apache + Wordpress redirecting to localhost/127.0.0.1? I've tried a lot of different fixes, but none have worked for me. I can go to http://domain.com/wp-admin just fine and use everything there normally. But if I try to go to http://domain.com it redirects to 127.0.0.1. Everything also works fine if I just run through Apache. Here are the relevant portions of my nginx.conf: server { listen 80; server_name domain.com; root /var/www/html/wordpress; location / { try_files $uri $uri/ /index.php; } location ~ \.php$ { proxy_pass http://127.0.0.1:8080; } } Here are the relevant portions of my httpd.conf: Listen *:8080 ServerName <ip> <VirtualHost *:8080> ServerAdmin test@test DocumentRoot /var/www/html/wordpress ServerName domain.com </VirtualHost> This is what my nginx log loks like: <ip> - - [19/Jun/2012:22:35:35 +0400] "GET / HTTP/1.1" 301 0 "-" "Mozilla/5.0 This is what my httpd log looks like: 127.0.0.1 - - [19/Jun/2012:22:24:46 +0400] "GET /index.php HTTP/1.0" 301 - "-" -- WordPress Address (URL) and Site Address (URL) both have same http://domain.com

  Read the article

• Basic IPTables setup for OpenVPN/HTTP/HTTPS server

  - by Afronautica

  I'm trying to get a basic IPTables setup on my server which will allow HTTP/SSH access, as well as enable the use of the server as an OpenVPN tunnel. The following is my current rule setup - the problem is OpenVPN queries (port 1194) seemed to be getting dropped as a result of this ruleset. Pinging a website while logged into the VPN results in teh response: Request timeout for icmp_seq 1 92 bytes from 10.8.0.1: Destination Port Unreachable When I clear the IPTable rules pinging from the VPN works fine. Any ideas? iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A FORWARD -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT iptables -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT iptables -A INPUT -j REJECT iptables -A FORWARD -j REJECT

  Read the article

• Fresh install CentOS 6.4 64b with directadmin slowly consumes all memory and crashes

  - by Coen Ponsen

  Dear server fault community, This is my first question on server fault, i'm new to server (mis)configuration so please forgive me for asking something stupid :) I'm running Directadmin on a CentOS 6.4 64b with 4GB memory and over 10000Gh virtual machine. I migrated my websites because my former vps couldn't keep up anymore. Only half of the websites from this 1GB machine were migrated jet. So the migration is still in progress and already my server crashes every day. The server performance up until that moment is perfect. The directadmin log files show nothing out of the ordinary. Yesterday only the mysql server crashed but it also crashed the entire machine before. The memory usage in DA seems to be normal: directadmin directadmin (pid 3923 22158 22159 22160 22161 22162 )8.75 MB dovecot dovecot (pid 3851 ) 47.8 MB exim exim (pid 1350 ) 1.29 MB httpd (pid 21525 21528 21529 21530 21531 21532 21546 21571 21742 21743 21744 )490.4 MB mysqld mysqld (pid 1299 ) 287.8 MB named named (pid 3807 ) 16.3 MB proftpd proftpd (pid 1481 ) 1.91 MB sshd sshd (pid 1173 21494 ) 5.16 MB Restarting services immediately frees up memory, but slowly over time the memory usage increases(about 24 hours to crash). The commands: # sync # echo 3 > /proc/sys/vm/drop_caches Will free al memory correct. I could just create a cronjob but it seems the wrong way around to me. I can't seem to pinpoint the cause. Any advices, references or tips are highly appreciated! Greetings, Coen edit: free -m : after drop_caches: total used free shared buffers cached Mem: 3830 735 3095 0 0 21 -/+ buffers/cache: 712 3117 Swap: 991 0 991 I'll post another one this evening.

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• does leaving the laptop cord in break the cord?

  - by firedrake

  i recently got a new cord for my laptop because the cord i had before broke.im not sure how it got messed up, but one moment it charged my laptop and the next moment it didn't. i then got a new cord. the new cord worked perfectly fine until now, and it has only been a month. the cord wont work unless i am pressing it into the socket, which i am currently doing. the only thing i can find in common with the cords is that i leave them plugged in 24/7. my brother says that is the problem, but i do not think it is.any tips or hints? im going to use duct tape to keep the pressure on the cord till i can find a better solution(im also thinking it could be the hole i plug it into on the back of my computer, but im focusing on the other idea for now.if i wiggle the plug part in the socket of my computer it will stop charging unless im pressing it in or to the side) any help or ideas are appreciated. not sure if this will help but i use a gateway with windows vista. thanks

  Read the article

• How to remotely connect using perfmon?

  - by user36914

  Suprised there is not a ton of information on google when i search for this but there is not. Lot of people asking the question but i none of them have any good answers. I have a remote computer running hyper-v (server) running a Windows 7 x64 guest (guest). Occasionally i won't be able to remote desktop to guest. I will then remote to server and see that the guest instance is constantly using about 25% of the cpu. WHen i try to connect directly from server i will get the login screen but as soon as i type the password in it will just stay at the windows 7 login screen but the account names will disappear and it will not log in. It responds to pings though. I don't know how else to diagnose other than trying to run perfmon remotely. It only happens like every 3 weeks and i run it 24/7. So i'm trying to run remote desktop remotely. I tested this out on a local vm i have running under vmware. When i try to connect using perfmon to my local vm i get this error: "when attempting to connect to the remote computer the4 following system error occurred: the network path was not found" I found in another past to start the remote registry service and when i start the service i get this error: "No such interface supported" Anyways, how do i remotely connect to another machine with perfmon or if anyone has a better idea how i can diagnose the problem above then let me know.

  Read the article

• finding files that match a precise size: a multiple of 4096 bytes

  - by doub1ejack

  I have several drupal sites running on my local machine with WAMP installed (apache 2.2.17, php 5.3.4, and mysql 5.1.53). Whenever I try to visit the administrative page, the php process seems to die. From apache_error.log: [Fri Nov 09 10:43:26 2012] [notice] Parent: child process exited with status 255 -- Restarting. [Fri Nov 09 10:43:26 2012] [notice] Apache/2.2.17 (Win32) PHP/5.3.4 configured -- resuming normal operations [Fri Nov 09 10:43:26 2012] [notice] Server built: Oct 24 2010 13:33:15 [Fri Nov 09 10:43:26 2012] [notice] Parent: Created child process 9924 [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Child process is running [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Acquired the start mutex. [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Starting 64 worker threads. [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Starting thread to listen on port 80. Some research has led me to a php bug report on the '4096 byte bug'. I would like to see if I have any files whose filesize is a multiple of 4096 bytes, but I don't know how to do that. I have gitBash installed and can use most of the typical linux tools through that (find, grep, etc), but I'm not familiar enough with linux to figure it out on my own. Little help?

  Read the article

• Get Matrox Millenium video card working in Ubuntu 9.10

  - by wcoenen

  I have installed Ubuntu 9.10 on an old PC and it is mostly working, except for some heavy drawing defects that show up whenever I start dragging a window or scrolling inside a window or menu. It looks like the video driver copies the rectangle being moved to the wrong location. I have taken a look in /var/log/Xorg.0.log and the following line shows the detected video card: (--) PCI:*(0:0:8:0) 102b:0519:0000:0000 Matrox Graphics, Inc. MGA 2064W [Millennium] rev 1, Mem@ 0xf9800000/16384, 0xfb000000/8388608, BIOS @0x????????/65536 (==) Using default built-in configuration (30 lines) (==) --- Start of built-in configuration --- Section "Device" Identifier "Builtin Default mga Device 0" Driver "mga" EndSection How do I fix the drawing defects? It turned out that the 24 bit color depth (automatically selected by ubuntu 9.10) was the problem; apparantly the mga driver doesn't handle this well for cards with little memory. I took the following steps to resolve the issue (you can skip the first three steps if you already have a semi-working xorg.conf file): Reboot ubuntu in recovery mode, to get a root console without X running. Run Xorg -configure to generate a xorg.conf.new file Copy the file to /etc/X11/xorg.conf with cp xorg.conf.new /etc/X11/xorg.conf (assuming it didn't exist yet; that's why I generated it) Open the new config file with sudo nano /etc/X11/xorg.conf and make sure the screen section is configured for 16 bit color depth like this: Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection EndSection I can't guarantee those were the only important changes I made - I tried a few things in my attempts to create a valid xorg.conf file. But I'm pretty sure that the screen section was the important part.

  Read the article

• 150 TB and growing, but how to grow?

  - by seandavi

  My group currently has two largish storage servers, both NAS running debian linux. The first is an all-in-one 24-disk (SATA) server that is several years old. We have two hardware RAIDS set up on it with LVM over those. The second server is 64 disks divided over 4 enclosures, each a hardware RAID 6, connected via external SAS. We use XFS with LVM over that to create 100TB useable storage. All of this works pretty well, but we are outgrowing these systems. Having build two such servers and still growing, we want to build something that allows us more flexibility in terms of future growth, backup options, that behaves better under disk failure (checking the larger filesystem can take a day or more), and can stand up in a heavily concurrent environment (think small computer cluster). We do not have system administration support, so we administer all of this ourselves (we are a genomics lab). So, what we seek is a relatively low-cost, acceptable performance storage solution that will allow future growth and flexible configuration (think ZFS with different pools having different operating characteristics). We are probably outside the realm of a single NAS. We have been thinking about a combination of ZFS (on openindiana, for example) or btrfs per server with glusterfs running on top of that if we do it ourselves. What we are weighing that against is simply biting the bullet and investing in Isilon or 3Par storage solutions. Any suggestions or experiences are appreciated.

  Read the article

• NAT via iptables and virtual interface

  - by Alex

  I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

  Read the article

• Router intermittently failing

  - by nomen

  My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

  Read the article

• MysqlTunner and query_cache_size dilemma

  - by wbad

  On a busy mysql server MySQLTuner 1.2.0 always recommends to add query_cache_size no matter how I increase the value (I tried up to 512MB). On the other hand it warns that : Increasing the query_cache size over 128M may reduce performance Here are the last results: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.25-1~dotdeb.0-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 6G (Tables: 195) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 51 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 19h 17m 8s (254M q [1K qps], 5M conn, TX: 139B, RX: 32B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 24.2G global + 92.2M per thread (1200 max threads) [!!] Maximum possible memory usage: 132.2G (139% of installed RAM) [OK] Slow queries: 0% (2K/254M) [OK] Highest usage of available connections: 32% (391/1200) [OK] Key buffer size / total MyISAM indexes: 128.0M/92.0K [OK] Key buffer hit rate: 100.0% (8B cached / 0 reads) [OK] Query cache efficiency: 79.9% (181M cached / 226M selects) [!!] Query cache prunes per day: 1033203 [OK] Sorts requiring temporary tables: 0% (341 temp sorts / 4M sorts) [OK] Temporary tables created on disk: 14% (760K on disk / 5M total) [OK] Thread cache hit rate: 99% (676 created / 5M connections) [OK] Table cache hit rate: 22% (1K open / 8K opened) [OK] Open file limit used: 0% (49/13K) [OK] Table locks acquired immediately: 99% (64M immediate / 64M locks) [OK] InnoDB data size / buffer pool: 6.1G/19.5G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 192M) [see warning above] The server has 76GB ram and dual E5-2650. The load is usually below 2. I appreciate your hints to interpret the recommendation and optimize the database configs.

  Read the article

• Tuning up a MySQL server

  - by NinjaCat

  I inherited a mysql server, and so I've started with running the MySQLTuner.pl script. I am not a MySQL expert but I can see that there is definitely a mess here. I'm not looking to go after every single thing that needs fixing and tuning, but I do want to grab the major, low hanging fruit. Total Memory on the system is: 512MB. Yes, I know it's low, but it's what we have for the time being. Here's what the script had to say: General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries When making adjustments, make tmp_table_size/max_heap_table_size equal Reduce your SELECT DISTINCT queries without LIMIT clauses Increase table_cache gradually to avoid file descriptor limits Your applications are not closing MySQL connections properly Variables to adjust: query_cache_limit (> 1M, or use smaller result sets) tmp_table_size (> 16M) max_heap_table_size (> 16M) table_cache (> 64) innodb_buffer_pool_size (>= 326M) For the variables that it recommends that I adjust, I don't even see most of them in the mysql.cnf file. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_buffer_pool_size = 220M innodb_flush_log_at_trx_commit = 2 innodb_file_per_table = 1 innodb_thread_concurrency = 32 skip-locking big-tables max_connections = 50 innodb_lock_wait_timeout = 600 slave_transaction_retries = 10 innodb_table_locks = 0 innodb_additional_mem_pool_size = 20M user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking bind-address = localhost key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 4 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M log_error = /var/log/mysql/error.log expire_logs_days = 10 max_binlog_size = 100M skip-locking innodb_file_per_table = 1 big-tables [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M !includedir /etc/mysql/conf.d/

  Read the article

• Pull network or power? (for contianing a rooted server)

  - by Aleksandr Levchuk

  When a server gets rooted (e.g. a situation like this), one of the first things that you may decide to do is containment. Some security specialists advise not to enter remediation immediately and to keep the server online until forensics are completed. Those advises are usually for APT. It's different if you have occasional Script kiddie breaches. However, you may decide to remediate (fix things) early and one of the steps in remediation is containment of the server. Quoting from Robert Moir's Answer - "disconnect the victim from its muggers". A server can be contained by pulling the network cable or the power cable. Which method is better? Taking into consideration the need for: Protecting victims from further damage Executing successful forensics (Possibly) Protecting valuable data on the server Edit: 5 assumptions Assuming: You detected early: 24 hours. You want to recover early: 3 days of 1 systems admin on the job (forensics and recovery). The server is not a Virtual Machine or a Container able to take a snapshot capturing the contents of the servers memory. You decide not to attempt prosecuting. You suspect that the attacker may be using some form of software (possibly sophisticated) and this software is still running on the server.

  Read the article

• Could 0x800CCC0E in Outlook be caused by bad wireless connection?

  - by AndrejaKo

  I have a computer connected to a WiFi access point/router/modem. Sometimes, I get page not found errors and similar when opening a browser window, sometimes pings fail and it looks like the router's signal isn't very good. On the other hand, I get around 4 bars of signal strength in windows and graph looks good in Inssider. I also never get dropped connection to the router. My main problem is that I often get errors (such as 0x800CCC0E) in Outlook 2010 that after some searching appear to be connected to bad server connection. I'm using GMail over IMAP and all settings are correct. I didn't have similar errors on my previous router, but I'm not 100% sure that they appeared after switching to current one. It may have worked for some time without errors. There are also around 3000 messages on the server and the size of mailbox is around 12 GiB, which may contribute to the problems. On the other hand, there are at least 24 other networks in the 2.4 GHz range which I'm using and the number may have increased since I switched routers. Should I try solving this by getting a router with stronger signal?

  Read the article

• Random “Lost connection to MySQL server at 'reading initial communication packet', system error: 0”

  - by user1606545

  Sometimes I get the error from MYSQL server: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 I cannot find the cause, since most of the time it works, but every week for some hours I get this error. I googled, but there seem to be only users which have this error permanently. But in this case, it only occurs sometimes. I checked hosts.allow and hosts.deny, but the host is allowed and not denied. Also sometimes I get the error: File './database/table.MYD' not found (Errcode: 24) It occurs very rarely. But it occurs for some hours once a week, sometimes on multiple days, but suddenly the problem disappears again. I have checked the open files limit. It's 2048 and should be absolutely enough. I also tried to increase the number of open files nevertheless, but no effect. I thought, perhaps the process does not close some tables. But this is impossible, because after a while everythings o.k. again and the process opens maximum 100 tables at once. I also checked the MySQL-runtime-environment, and there were 930 opened files. I cannot explain that. After a while it's 129. I am running a MySQL-Server on a SUSE-Linux machine. I connect to the MySQL-Server from another host by the command line tool "mysql" and by MySQL-C-connector. The MySQL-Server is version 5.0.67.

  Read the article

• ATI Radeon 5670 Won't Show Resolutions over 1400x900

  - by Phil Sandler

  Just got my new Dell computer with Windows 7 and an ATI Radeon 5670. I attached it to my current monitor, which is a Samsung 24" (2443bwt). Windows 7 does not allow me to display in resolutions greater than 1400 x 900. The setup through a VGA cable into the VGA port of the card. The card also has a DVI port, but I need to use the VGA port because a KVM that supports VGA only. My old PC (which is Windows XP, GeForce 8600 video) can display in 1900 x 1200 on the same monitor (which is what I want) and even higher. It does this through a vga cable also connected to the KVM (through the DVI port but using an adapter). I have tried the same setup (DVI = VGA adapter) on the new PC and nothing changed. I have tried: Updating the drivers via Windows "Update Driver" (says they are current) Installing the updated version of the drivers from ATI (made no difference) Installing Powerstrip (all the options I would need for a custom resolution are greyed out) Installing the drivers/software from ATI caused the ATI Catalyst Control Center software to stop functioning, so I can no longer even start it. I have found some references to other people having this problem and instructions on cleaning the software off and reinstalling it (as uninstalling normally doesn't solve it). I will try this tonight. In any case, I didn't see any options in CCC that would allow me to override the settings for max resolution. However I didn't tinker with it too much before I tried updating the drivers, so I may have missed a setting. I contacted Samsung via online chat and they say it's a problem with the video card/driver (of course--what else would they say?). Any thoughts on what else I could try?

  Read the article

• Remote Desktop leaves host unresponsive

  - by Jeff Dalley

  I have my desktop PC at home set up to accept remote connections, and I often connect to it from work on my laptop via mstsc.exe. However, every time I remote to it, I find when I go home that despite the monitor being on - it's not receiving an image and it looks as though the computer is hibernating/asleep. I basically have to restart it whenever I get home and I know there's an answer for why its doing this. More details: When exiting the remote session, I have tried both logging off the account, and closing the RDP window without logging off; both give the same result. When I get home to the desktop I of course try moving the mouse, ctrl+alt+del to see if its responsive to restart, multiple key-press to see if I can get any audio out of it; It seems pretty obvious its sleeping/hibernating in some way: Nothing happens in any of these cases and a physical restart is necessary. Both desktop and laptop are running Windows 7 Ultimate. I'm thinking it really is sleeping/hibernating it, and I'm not sure why because left alone my desktop's power options are set to never turn off the HDD or change its state - I leave it on 24/7. This could be a stupid error on my part but I just can't see it! Thanks.

  Read the article

• how to get ip address of a PPP(Point-to-Point Protocol) network interface?

  - by Xsmael

  I have a Linux machine with two network interfaces, and I'd like to get the IP address of the PPP interface w1g1 but it doesn't show up in ifconfig. There is a public IP on the PPP interface, but there is no internet connection, I'm trying to troubleshoot but I need to get the IP address of the interface and I can't. ifconfig : eth0 Link encap:Ethernet HWaddr 00:30:48:8D:F0:2C inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe8d:f02c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9970 errors:0 dropped:567 overruns:0 frame:0 TX packets:4338 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1441024 (1.3 MiB) TX bytes:915814 (894.3 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:675 errors:0 dropped:0 overruns:0 frame:0 TX packets:675 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50659 (49.4 KiB) TX bytes:50659 (49.4 KiB) w1g1 Link encap:Point-to-Point Protocol UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1 RX packets:748994 errors:0 dropped:0 overruns:0 frame:0 TX packets:748992 errors:0 dropped:0 overruns:0 carrier:3 collisions:0 txqueuelen:100 RX bytes:179758560 (171.4 MiB) TX bytes:179758080 (171.4 MiB) Interrupt:177 Memory:f881c400-f881e3ff w1g1 is connected to a modem by an RJ45<-Serial cable and the modem is connected to the phone line. The modem is a NOKIA DNT2Mi you can see it here Routing table : 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 169.254.0.0/16 dev eth0 scope link default via 192.168.2.180 dev eth0

  Read the article

• 64-bit Windows 7 gets stuck on logo screen on bootup

  - by Richard B

  I've had a PC running Windows 7 in my office which I'm not using at the moment (cause I'm working elsewhere as a consultant atm), I'm only accessing the PC using Team Viewer (http://www.teamviewer.com/) which means the PC has been running for quite some time now. I've restarted it maybe twice a week though. A few days ago I couldn't access it using Team Viewer and when I got to the office the screen was black with only the mouse pointer showing. The PC has four hard disks, three of them (all 1Tb) is using RAID 5. This is what I've done so far: I reboot and everything seems to load correctly. I get to a screen that gives me two choices - boot Windows normally or perform a startup repair. Choosing to boot Windows only gets me to the Windows 7 logo screen which only animates over and over again. Choosing to repair gets me to the repair screen that "checks for problems" and then it gets stuck on the "Attempting repairs..."-screen (I let it run for about 24 hours before giving up). What is the next step to take? I don't have any backups and no system restore points saved. I can access files and folders through a terminal window using a Windows 7 DVD so I guess nothing is lost yet... Please help me, thanks!

  Read the article

• ActiveMQ Configuration with KahaDB

  - by xeraa

  We are using ActiveMQ 5.6.0 with KahaDB. It has produced quite some log files, which is to be expected with our infrastructure, looking like this: $ ll -h /opt/activemq/data/kahadb/ total 969M drwxr-xr-x 2 root root 4.0K Nov 3 12:47 ./ drwxr-xr-x 3 activemq activemq 4.0K Sep 24 12:12 ../ -rw-r--r-- 1 root root 39M Oct 16 07:57 db-202.log -rw-r--r-- 1 root root 38M Oct 16 07:57 db-203.log -rw-r--r-- 1 root root 33M Oct 17 08:12 db-238.log ... No more messages were processed, when we ran into the 1GB temp usage limit. Or that's what we are assuming, is that correct? The configuration looks like this: <systemUsage> <systemUsage> <memoryUsage> <memoryUsage limit="512mb"/> </memoryUsage> <storeUsage> <storeUsage limit="3 gb"/> </storeUsage> <tempUsage> <tempUsage limit="1 gb"/> </tempUsage> </systemUsage> </systemUsage> After cleaning up the log files and being way below the limits, still no messages were consumed by AMQ. Only when we manually purged a route, messages were starting to be delivered again. So we need to ensure, that the KahaDB log size always stays below the temp usage, right? And that delivery was not picked up after fixing that is a bug or are there any other steps to be taken?

  Read the article

< Previous Page | 180 181 182 183 184 185 186 187 188 189 190 191  | Next Page >