Search Results

Search found 5572 results on 223 pages for 'cpu'.

Page 186/223 | < Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >

  • mod_fcgi in virtualmin: graceful kill fail, sending SIGKILL?

    - by mgjk
    Yesterday around 1am, our server ground to a crawl. This doesn't happen often, but I'm trying to get to the bottom of it. There is no unusual traffic volume, no unusual processes running, just all of the sudden the server started killing fcgid processes. [Thu Aug 02 01:17:32 2012] [warn] mod_fcgid: process 26460 graceful kill fail, sending SIGKILL ... for as many fcgid processes as we have... CPU idle fell to 0% and I/O seemed to take up most of the load. The issue lasted about 5 minutes. I suspect there was some swap activity, although I'm not sure if it was due to killed processes being swapped in to die, or if it was because some process ramped up memory usage faster than my process watching scripts can see them. The oom-killer wasn't triggered (at least it's not logged), so I think this was Apache for some reason restarting the processes. This is not regular, and nothing obvious appears in cron. Is there a normal Apache process which might cause this? We run dozens of different sites, and it was late at night, so volume was very, very low. (maybe 200 requests in a 10 minute period).

    Read the article

  • Any dangers in using DDR memory with a higher frequency than the FSB?

    - by raw_noob
    I'm looking to upgrade memory in an older motherboard. The processor is an AMD Sempron 2500+ with a maximum speed of 333/166MHz. The motherboard is an MSI MS-7061 (KV3M-V), which accepts up to 2Gb of DDR memory maximum PC2700 in 2 slots and has a maximum FSB of 333MHz. The board does not have dual-channel support. Existing memory includes a stick of 512Mb PC3200, which seems to be running OK (presumably at PC2700) but is rated 200MHz, which is below the FSB speed. The other stick is 256Mb PC2100/133MHz, again below the FSB speed. (All figures from CPU-Z.) I have a chance to acquire a single used stick of PC3200/400MHz memory very cheaply. Crucial's system scanner seems to suggest that this will be OK with my system, but other sites have suggested that running memory with a higher frequency than the FSB can cause instability. Is this true? Would I be better waiting until I can buy the correct PC2700/333MHz stick? I'm assuming that the mixed memory I have at present is running as 768Mb at 133MHz. Is this a reasonable assumption? If so, would you expect the performance differences between 768Mb/133MHz and 1Gb/333MHz to be very noticeable? If I install the new 1Gb/400 or 333MHz stick in slot 1, am I right in thinking that adding back the existing 512Mb/200MHz stick in slot 2 would pull the whole 1.5Gb system memory speed down to 200MHz? If so, which would be better - 1.5Gb/200MHz, or the single 1Gb stick at the full 333MHz that the FSB permits? Is more headroom more important than extra speed? Any help - or even opinions - gratefully received. I can't find reliable information, and I can't afford to make expensive mistakes.

    Read the article

  • MRTG Monitoring of Disk

    - by Antitribu
    I am trying to monitor Disk usage over SNMP using MRTG on CentOS5.2. I'm open to any suggestions as to the best way to achieve this (I would also like to do other metrics like CPU). Please don't assume I know anything about MRTG. I am using the following config: LoadMIBs: /usr/share/snmp/mibs/UCD-SNMP-MIB.txt,/usr/share/snmp/mibs/TCP-MIB.txt workdir: /var/www/html/mrtg/temp/ # # Disk Usage Monitoring # Target[servername.]: dskPercent.0&dskPercent.0:[email protected] Title[servername.]: / on servername routers.cgi*Desc[servername.]: / on servername routers.cgi*ShortDesc[servername.]: / MaxBytes[servername.]: 100 AbsMax[servername.]: 100 Options[servername.]: growright,nopercent,gauge YLegend[servername.]: used disk space ShortLegend[servername.]: % used Legend1[servername.]: usage Legend2[servername.]: usage Legend3[servername.]: peak usage Legend4[servername.]: peak usage LegendI[servername.]: usage LegendO[servername.]: usage routers.cgi*Icon[servername.]: disk-sm.gif routers.cgi*Options[servername.]: noo,nomax,noabsmax Unscaled[servername.]: dwmy I receive the errors: Unknown SNMP var dskPercent.0 at /usr/bin/mrtg line 2035 Unknown SNMP var dskPercent.0 at /usr/bin/mrtg line 2035 From forum surfing etc the suggestion is to use the fully qualified OIDs, I'd like to avoid this (for readability). So essentially I'm wondering where can I find a mib file compatible with mrtg for it's reference or a working config file.

    Read the article

  • Load is 0, yet site crawls (sometimes). What gives?

    - by Yegor
    I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

    Read the article

  • Graphics Artifacts/ Texture Flickering

    - by Cerin
    Hey I been having some problems with artifacts in games. Sometimes textures flicker. Artifacts of various shapes and sizes show up usually after a couple games of dota 2. I built my computer almost exactly one month ago and it has been doing this pretty much from the start except before the artifacts I believe just flashed on screen fast enough to where I couldn't tell what it was but I still noticed. In dota I've seen green triangular artifacts among other things. I've tried running Furmark for a while but even though it pushes the gpu much harder than dota 2, there are still no artifacts. It maxes in furmark at about 60C and running every game I've tried on it at 40C. CPU and system temp don't usually get higher than 40C either. These are my system specs: Gigabyte Z68 Intel Motherboard 16 GB Gskill Ripjaws SDRAM DDR3 Sapphire Radeon HD 7770 GHz edition Intel Core i5-2500k (with built in gpu) Corsair 750 Watt PSU windows 7-64 bit I have the latest drivers for everything. What should I do about this? Try to RMA my graphics card? Are there other things that could be causing this?

    Read the article

  • Windows/IIS Hosting :: How much is too much?

    - by bsisupport
    I have 4 Windows 2003 servers running IIS 6. These servers host a bunch of unique web sites (in that they are all different in build/architecture/etc). The code behind these sites range from straight HTML, classic ASP, and 1.1/2.0/3.x flavors of .NET. Some (most) of the sites use a SQL backend, which is hosted on one or two different servers – not the IIS servers themselves. No virtualization on these servers and no load balancing for these particular sites. The problem I’m running into is coming up with some baseline metrics to determine, or basically come up with a “baseline score” to know when a web server has reached its hosting limit. Today, some basic information about each server is used: how much bandwidth does the server pump out, hard drive space availability, and basic (very basic) RAM & CPU utilization (what it looks like at peak traffic times.) I would be grateful if those of you that are 1000x smarter than I am could indulge me with your methods of managing IIS environments. Whether performance monitoring specifics, “score” determination as I’m trying to determine, or the obvious combination of both. Thanks in advance.

    Read the article

  • Multiple servers vs 1 big server performace

    - by pistacchio
    Hi to all! My team of developers has suggested a server structure for an upcoming project we are developing. Our structure is "logical", meaning that the various logical components of the application (it is a distributed one) relies on different servers. Some components are more critical than others and will be subjected to more load. Our proposal was to have 1 server per component but the hardware guys suggested to replace the various machines with a single, bigger one with virtual servers. They're gonna use Blade Servers. Now, I'm not an expert at all, but my question to the guys was: so if we need, for example, 3 2GHz CPU / 2GB RAM machines and you give me 1 machine with 3 2GHz CPUs and 6 GB of RAM it is the same? They told me it is. Is this accurate? What are the advantages or disadvantages of both the solutions? What are the generally accepted best practices? Could you point out some URL reference dealing with the problem? Thank you in advance! EDIT: Some more info. The (internet / intranet) application is already layered. We have some servers on the DMZ that will expose pages to the internet and the databases are on their own machines. What we want to split (and they want to join) are some webservers that mainly expose webservices. One is a DAL that communicates with the database layer, one is our Single Sign On / User Profile application that gets called once per page and one is a clone of what seen on the Internet to be used on our lan.

    Read the article

  • Hadoop streaming job on EC2 stays in "pending" state

    - by liamf
    Trying to experiment with Hadoop and Streaming using cloudera distribution CDH3 on Ubuntu. Have valid data in hdfs:// ready for processing. Wrote little streaming mapper in python. When I launch a mapper only job using: hadoop jar /usr/lib/hadoop/contrib/streaming/hadoop-streaming*.jar -file /usr/src/mystuff/mapper.py -mapper /usr/src/mystuff/mapper.py -input /incoming/STBFlow/* -output testOP hadoop duly decides it will use 66 mappers on the cluster to process the data. The testOP directory is created on HDFS. A job_conf.xml file is created. But the job tracker UI at port 50030 never shows the job moving out of "pending" state and nothing else happens. CPU usage stays at zero. (the job is created though) If I give it a single file (instead of the entire directory) as input, same result (except Hadoop decides it needs 2 mappers instead of 66). I also tried using the "dumbo" Python utility and launching jobs using that: same result: permanently pending. So I am missing something basic: could someone help me out with what I should look for? The cluster is on Amazon EC2. Firewall issues maybe: ports are enabled explicitly, case by case, in the cluster security group.

    Read the article

  • Wake for Network Access Apache servr in OS X 10.8, followup

    - by Gary
    Sorry, I can't seem to post this response within the same thread. Thank you both (Zoredache and Gordon) for your answer. But the fix seems temporary. I entered the command you suggested, and it seemed to work: ...smith$ Registering Service ApacheNoDoz._http._tcp.local port 80 DATE: ---Fri 14 Sep 2012--- 12:04:15.813 ...STARTING... 12:04:16.566 Got a reply for service ApacheNoDoz._http._tcp.local.: Name now registered and active So, I checked for it on my G5: Browsing for _http._tcp Timestamp.....A/R Flags if Domain......Service Type...Instance Name (lots of Bonjour printers omitted)... 12:07:38.370..Add.....2..4 local.......... _http._tcp.........ApacheNoDoz 12:07:45.921..Rmv.....0..4 local..........._http._tcp.........ApacheNoDoz So, it was running at 12:07:38, at which time the host was asleep. But, shortly after, the activity seems to have been removed. I don't know why. Does this mean that I can never let the cpu sleep, or is there something else I have to set? Thanks, again.

    Read the article

  • Apache2: Limit simultaneous requests & throttle bandwidth per IP/client?

    - by xentek
    I want to limit simultaneous requests & throttle bandwidth per IP/Client on a single apache vhost. In other words, I want to ensure that this site, which hosts large media files, doesn't get hammered by someone trying to download everything all at once (just happened the other night). I'd like to limit the outgoing transfer speed overall for this site, as well as limit the number of connections a single IP can make to the server to a sane default (i.e. within normal browser limits for multiple requests so page loads aren't effected too much). Bonus points if I can actually scope it to file types (i.e. leave web files alone, but apply these rules to just the media files). We're running Ubuntu 9.04 on all the servers, and have two apache/php servers being load balanced via Round Robin by a squid proxy server. MySQL is running on its own box as well. We've got plenty of bandwidth to give them, so I don't really want overall caps, but just want to throttle the amount of memory/CPU it takes to serve this site. There other sites on these servers that we don't want to apply these rules too, just want to keep this one from hogging all the resources. Let me know if you need more info! Thanks in advance for your suggestions!

    Read the article

  • How can I install iTunes in such a way that it can't put any "hooks" or helper programs on my computer?

    - by Joshua Carmody
    I'm buying a new iPad, which means I must once again install iTunes. I've not used iTunes in more than 6 months, since I bought a new computer. I don't like iTunes, but I can live with using it to buy/manage media and sync my Apple devices when the program is open. What I would like to do though, is find a way to install iTunes in such a way that it has absolutely no effect on my system when it is closed. iTunes normally installs several helper programs such as iTunesHelper.exe, and the Bonjour service. These programs run in the background when iTunes is closed. You can force-close them, or remove them from your setup files, but iTunes will often put them right back when you run it. I know these programs are mostly harmless, but they have at times caused issues such as iTunes spending system resources trying to catalog media files or drives connected to VPN, or other issues. At best they're just one more small background process eating up a small piece of my CPU time and RAM. How can I run iTunes without letting it get it's "hooks" into my system? One thought I had is that I could create a Windows user account just for iTunes, and deny it admin privileges. Then if I installed iTunes using that account maybe anything it installed wouldn't affect the "main" account on my PC? But I'm not sure if that would work.... Failing that, maybe some kind of virtualization software or sandbox I could install it in? I'm open to any suggestions. My system is an Intel-based PC running Windows 7 Professional 64-bit. Thanks!

    Read the article

  • kde dropping keyboard

    - by shabbychef
    I am having problems with KDE 'dropping' my keyboard. It happens periodically when using my gentoo box directly, but has become much worse when accessing via NX (from a Mac laptop). Some possibly irrelevant clues: it appears to happen more often when the system is under higher CPU load the mouse continues to work, but no windows will accept any kind of keyboard focus. kwin will not accept tabbing between windows. when working on the machine directly, I can ctrl-alt-F1 to get to a shell (obviously this does nothing over NX). so I think it is KDE and not xorg. am running kwin-4.3.5-r1, and KDE-4.3.5 generally. this problem definitely appeared after upgrading to kde-4.x, but I do not remember if it appeared in kde-4.2. sometimes the keyboard will reappear, but sometimes I have to kill my kde session. playing with accessibility options or window-focus-stealing options in system-settings under kde will often make the keyboard responsive again, only to drop it perhaps minutes later. I had read online this might be an evdev problem under X (again, I think this is KDE, not X, but will try anything). as a result, I have fiddled with my xorg.conf endlessly. I even deleted it entirely and let nvidia-xconfig have a stab at it, with no luck I am tearing my hair out over this. I have done emerge -e xorg-server and am right now doing emerge -e kwin, to rebuild all packages that might be relevant. no luck with the xorg-server rebuild. any help appreciated. thanks,

    Read the article

  • Installing 64-bit Ubuntu Server 12.04 LTS, on a VM with VMWare Player, on a 64-bit Windows 7 PC

    - by WannaBeAGeek
    I'm trying to create a VM, using VMWare Player, with an ISO image of Ubuntu Server 12.04 (LTS). The machine I'm doing the installation on has an Intel(R) Core(TM) i5 CPU, and runs 64-bit Windows 7 I managed to create the VM (gave username, password, configured network etc), but I can't install Ubuntu Server. First I get this alert : Binary translation is incompatible with long mode on this platform. Disabling long mode. Without long mode support, the virtual machine will not be able to run 64-bit code. For more details see http://vmware.com/info?id=152. When I click OK, I get another alert : This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host supports Intel VT-x, but Intel VT-x is disabled. Intel VT-x might be disabled if it has been disabled in the BIOS/firmware settings or the host has not been power-cycled since changing this setting. (1) Verify that the BIOS/firmware settings enable Intel VT-x and disable 'trusted execution.' (2) Power-cycle the host if either of these BIOS/firmware settings have been changed. (3) Power-cycle the host if you have not done so since installing VMware Player. (4) Update the host's BIOS/firmware to the latest version. For more detailed information, see http://vmware.com/info?id=152. Then, when I click OK, my VM exists, and I get back to the VMWare Player home screen. I don't know much about hardware and virtualisation, so there might be some necessary info I'm not giving. Please don't hesitate to let me know what is missing in my post, for finding solutions. Thanks :)

    Read the article

  • Performance decrease in every game and application

    - by Márk Vincze
    When I start a game, initially it runs smoothly, but after a couple of minutes, the performance gradually decreases to the point of being unplayable (1-2 FPS). The sound also starts to lag at this point. This does not happen every time I start my PC, usually exiting the game, rebooting, then starting the game again solves the problem, and I can play with perfect FPS for as long as I want. I could not find any deterministic reason when this happens and when doesn't. It happens in every game I tried (SWTOR, Diablo 3, Skyrim), and not even games, but simple applications like a browser or the Control Panel can get unusably slow. This is a brand new PC I bought three months ago, and this problem occurs since the first day I've been using it. Could you provide any advice how to further diagnose the problem? I tried to reinstall Windows, and tried different video card drivers, but it did not help. It would be important to know whether this is a hardware or software problem, because I can use the warranty if it is a hardware issue. (I did not want to return the PC yet, because I can't reproduce the issue deterministically.) Spec of the pc: Motherboard: ASROCK H61M-HVS CPU: INTEL Core i3-2120 3.30GHz 1155 BOX Memory: KINGMAX 4096MB DDR3 1333MHz KIT Video card: GIGABYTE GV-R685OC-1GD HD6850 1GB GDDR5 PCIE HDD: SEAGATE 500GB Barracuda 7200rpm 16MB SATA3 ST500DM002 I am using Windows 7 64 bit. Thanks a lot in advance!

    Read the article

  • Spreadsheet application that can handle big data OS X

    - by Peter
    I've been working with Excel for quite a while for some statistical analysis that I do regularly. The size of the data that I'm working with has gotten much larger as of late, however. The layout of the databases in question is quite simple, usually just three rows which includes a UNIX timestamp, and EST value, a proprietary numeric value and finally an average of the rows that have a timestamp +/- 1000 that row's timestamp (little AVERAGEIFS() formula). That formula and the EST conversion are the only formulas in the sheet. I'm beginning to work with files with 500,000+ rows. Running the average formula down the entire row takes forever. The end result is the production of print-worthy graphs. I'm looking for either a UNIX CL utility or separate spreadsheet/database application that can handle this amount of data without melting my CPU or making me wait an hour. Is there anything out there? TL;DR: Simple excel sheet with over half a million rows is getting too slow to work with. OS X alternatives?

    Read the article

  • VMWare Workstation 8 Disk I/O & Hard Faults

    - by Scott
    I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

    Read the article

  • High fan speed with no reason

    - by Klaus
    For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

    Read the article

  • Windows 7 Blank Screen on Boot / Login

    - by Greg
    I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

    Read the article

  • CentOS Installation on a Cisco MCS 7800

    - by William
    Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

    Read the article

  • Automatic o/s reset on a dedicated internet browsing Windows 7 pc.

    - by camelCase
    I have just purchased a new Acer Revo nettop PC for dedicated internet browsing. It will be the only pc on a home network. My original plan was to install one virtual PC for family browsing, another for remote web based server administration and ban browser use from the host Windows 7 o/s. The idea was that I could recover to a fresh VHD image once a week to eliminate any build up of malware inside the browser VMs. However now I am looking for alternative solutions since the Intel Atom cpu does not have hardware VT support which Windows Virtual PC requires. Would it be possible to engineer some type of routine overnight host o/s wipe and recovery? I guess cyber cafes do something like this? The only user data that would need to be retained across a recovery would be browser bookmarks but these could be exported to remote service. Edit 1: I am thinking the o/s reset could be done via some disk image recovery process. Edit 2: Just had a brainwave. Routine browsing could be done via the new Google Chrome O/S. I have just seen a video of the Google Chrome o/s booting off a usb pen drive in seconds.

    Read the article

  • Win/Bios showing wrong RAM in Gateway Netbook?

    - by Ael
    I've seen similar problems, but this seems slightly unique, maybe... I have a Gateway LT21 netbook, Win7. I've upgraded RAM from 1gb to 2gb. It didn't work. So I updated to the latest Bios 1.25, then it worked. 2gb was recognized in the Bios and in Windows. Every was fine. Now today it seemed slow and, to my surprise, both the Bios and Win show only 1gb. :/ I've run memory diagnostic, no error. I entered bios and hit Exit and Save. Still 1gb. I took out the ram, put it back. Still 1gb. :/ CPU-Z shows 2048mb/2gb of RAM. Further testing: if i put in the old 1gb ram, turn on, then put in the new 2gb ram again, the Bios and Win show 2gb of ram. BUT, once restarted at all (even from Bios) it seems to go back to showing incorrect 1gb ram again. :// (There are very few options in the bios, none appear memory-related.) Any ideas?

    Read the article

  • What is best configuration settings for Wordpress and MySQL on Win2008 + IIS7 stack?

    - by holiveira
    I currently have four blogs that uses Wordpress running on a shared hosting company. This blogs have a considerable amount of visits and I'm constantly receiving warnings from the hosting company saying that I'm consuming too much server CPU. Considering the fact that I have a dedicated server in another company with plenty of idle resources (it has a quad core Xeon 2.5GHz and 8GB of Ram and run on Win2008) I'm planning to move the blogs to this server in order to have some more freedom. I'm currently using this server to host some web applications using ASP.Net and SQL Express. I've installed a blog to test and it worked fine, but some issues appeared and raised some questions in my mind: How to properly set the permissions in the folders used by wordpress plugins, I mean, what permissions should I set for the IIS_User in some folders so that the plugins works correctly? What's the best caching plugin to use considering this is a Window Server? In the previous hosting company I used the WPSuperCache, but it was a Linux Stack. Or should I ignore the caching plugins and use the Dynamic Caching Feature of IIS7? How can I optmize the MySQL server running in this server (specially the settings regarding memory and caching) How can I protect the admin folders against hacker attacks? I know some people will advice me not to run Wordpress in a Windows stack, but that's my only choice. I don't even know were to start managing and LAMP stack, don't have the time to do so nor the money to rent another server.

    Read the article

  • Doesn't VirtualBox 4.0 support drag-drop file copy yet?

    - by Benjamin
    Version 4.0.0 will be new major release. The following major new features were added: -New settings/disk file layout for VM portability; see the manual for more information. -Open Virtualization Format Archive (OVA) support; see the manual for more information. -VMM: support more than 1.5/2 GB guest RAM on 32-bit hosts -Language bindings: uniform Java bindings for both local (COM/XPCOM) and remote (SOAP) -invocation APIs -Chipset: added support for the Intel ICH9 chipset with 3 PCI buses, PCI express and -Message Signaled Interrupts (MSI) -Audio: Intel HD Audio is now available as guest hardware, for better support with modern -guest operating systems (e.g. 64-bit Windows; bug #2785). -GUI: redesigned user interface with guest window preview -GUI: new display mode with downscaled guest display -Resource control: added support for limiting a VM's CPU time and IO bandwidth. -Storage: support asynchronous I/O for iSCSI, VMDK, VHD and Parallels images -Storage: support for resizing VDI and VHD images -Windows Additions: support for automatically updating the Guest Additions (requires -installed Windows Guest Additions 4.0 or later) -Guest Additions: support for copying files into the guest file system What does the last line mean? I thought this is a drag-drop file copy feature like VMWare. I tried that. But I couldn't copy by drag-drop, ctrl-c ctrl-v either. Edit: I mean VBox 4.0 beta, not 3.x The release note is here. Download link is here.

    Read the article

  • Connections to SSH and Samba suffer from heavy delay

    - by Till Helge Helwig
    There are a lot of questions about SSH connections being delayed, which usually can be fixed by disabling the DNS lookups. Unfortunately this doesn't seem to be my problem. Our development server is accessed via SSH and Samba. When opening a connection to the server (either SSH or Samba) it takes a very long time. Accessing a Samba share via Windows is basically impossible because there is a timeout. Using smbclient works, but takes ages. When opening a SSH connection I get immediately prompted for the password and after hitting Enter the terminal instantly shows the MOTD. Afterwards it takes about a minute for the prompt to appear. I watched the load of the server while connecting via SSH and Samba and could not find anything out of order. There is nothing out of the ordinary running and hogging up memory and CPU or something. I have no clue where this delay might come from. I already tried UseDNS no in sshd_config and proxy_dns = no in smb.conf, but to no avail. Any idea about what might cause this would be greatly appreciated!

    Read the article

  • sysbench memory test on ec2 small instance

    - by caribio
    I'm seeing a problem with sysbench memory test (the default version that's compiled in). This is on Ubuntu Maverick, sysbench installed via apt-get install sysbench. Running the same thing on Ubuntu @ Rackspace worked just as expected. While the CPU and I/O tests worked fine on EC2 servers, the memory test just runs without doing anything (notice the 0M in the test results). The instance used was the publicly available 'stock' Ubuntu image with no changes to it: ./ec2-run-instances ami-ccf405a5 --instance-type m1.small --region us-east-1 --key mykey Supplying more arguments (such as: --memory-block-size=1K --memory-total-size=102400M) didn't help. What am I doing wrong? Thanks. sysbench --num-threads=4 --test=memory run sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 4 Doing memory operations speed test Memory block size: 1K Memory transfer size: 0M Memory operations type: write Memory scope type: global Threads started! Done. Operations performed: 0 ( 0.00 ops/sec) 0.00 MB transferred (0.00 MB/sec) Test execution summary: total time: 0.0003s total number of events: 0 total time taken by event execution: 0.0000 per-request statistics: min: 18446744073709.55ms avg: 0.00ms max: 0.00ms Threads fairness: events (avg/stddev): 0.0000/0.00 execution time (avg/stddev): 0.0000/0.00

    Read the article

< Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >