Search Results

Search found 17129 results on 686 pages for 'wifi configuration'.

Page 188/686 | < Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• OS X mouse pointer speed varies with different mouse

  - by Stan

  OS X Snow Leopard It seems that when using different mice on OS X may have different pointer speed and scrolling speed. For example, when using my Logitech basic laser mouse, the pointer speed is like normal. But when using MX Performance or Anywhere, it's very slow, I will have to adjust the pointer speed in mouse configuration to max. Even with max, it's still a bit slow. Basically, just feel the plug and play on OS X is terrible. I need re-adapt to it every single time. This is not the case on Windows OS. Also, the mouse scrolling speed varies with different mouse too. But usually they are all very slow, usually scroll 1 line at a time. If I adjust it in mouse configuration, it turns to scroll too much lines. I have Logitech official mouse driver (LCC) installed. But either tuning in LCC or mouse configuration doesn't make things better. Has anyone have similar issue? How to resolve it? Please advise, thanks.

  Read the article

• Configuring DNS & MX records for exchange 2010

  - by Mahmoud Saleh

  i am trying to configure Exchange Server 2010 on Windows Server 2008 R2 to receive emails from the internet following the danscourses tutorials: and i followed this video for the DNS & MX records: http://www.youtube.com/watch?v=jdf_3DRssks i don't have any windows administration skills, and i am stuck with the DNS configuration. and the following are my domain configuration i got from the hosting. following are the steps i made: 1- Add new name server: add ns1.centors.com ip Exchange Server Public IP: 41.233.26.131 2- Change the A record change it to point to the public ip address Exchange Server Public IP: 41.233.26.131 3- New cname record for www and make it resolve to centors.com 4- New mx record for mail.centors.com 5- New A record for mail.centors.com: name: mail ip: Exchange Server Public IP: 41.233.26.131 6- new A record for ns1: ip: Exchange Server Public IP: 41.233.26.131 7- i made port forward in the router for SMTP and POP3 to the exchange server local ip address. ISSUE: i have a user account in the active directory, and the user is member of the domain, the user is [email protected] and when trying to login with this account in outlook 2010 on other machine using following data: account type: POP3 incoming mail server: mail.centors.com outgoing mail server: mail.centors.com i always get the error: Authorization failed, check your server settings. please advise what's wrong with the configuration, thanks in advance.

  Read the article

• Which linux distributions offer seamless support for UEFI and an LVM root out of the box?

  - by Jannik Jochem

  My new ultrabook (an Asus UX32VD) requires UEFI in order to boot from the internal harddisk. I use an LVM partition which contains my root fs and dual-boot Windows 8. I somehow managed to get this working on Sabayon Linux, however the overall process was pretty painful, and system upgrades keep breaking my configuration because everything depends on a hand-configured kernel and a hand-crafted GRUB2 configuration. This causes a lot of hassle and distractions for me, so I am considering to switch to a different distribution. However, I cannot find any concrete resources that precisely document the state of UEFI support in the popular distributions. As an example, the length of the Ubuntu wiki page on UEFI suggests that installing on UEFI systems is a non-trivial process, and this AskUbuntu thread on encrypted LVM on UEFI systems suggests that LVM might also be a problem. I know that this question seems somewhat open-ended, so I'll formulate concrete questions: Are there any Linux distributions with an installer that supports installing to an LVM root in a UEFI boot setting where Windows 8 is dual-booted? Which distributions support UEFI without having to jump through hoops in order to bootstrap into a UEFI-booted system or requiring manual configuration of the boot manager?

  Read the article

• nginx rewrite or internal redirection cycle

  - by gyre

  Im banging my head against a table trying to figure out what is causing redirection cycle in my nginx configuration when trying to access URL which does not exist Configuration goes as follows: server { listen 127.0.0.1:8080; server_name .somedomain.com; root /var/www/somedomain.com; access_log /var/log/nginx/somedomain.com-access.nginx.log; error_log /var/log/nginx/somedomain.com-error.nginx.log debug; location ~* \.php.$ { # Proxy all requests with an URI ending with .php* # (includes PHP, PHP3, PHP4, PHP5...) include /etc/nginx/fastcgi.conf; } # all other files location / { root /var/www/somedomain.com; try_files $uri $uri/ ; } error_page 404 /errors/404.html; location /errors/ { alias /var/www/errors/; } #this loads custom logging configuration which disables favicon error logging include /etc/nginx/drop.conf; } this domain is a simple STATIC HTML site just for some testing purposes. I'd expect that the error_page directive would kick in in response to PHP-FPM not being able to find given files as I have fastcgi_intercept_errors on; in http block and nave error_page set up, but I'm guessing the request fails even before that somewhere on internal redirects. Any help would be much appreciated.

  Read the article

• JBoss 5 on AIX 5.3

  - by jess

  I am a very newbie for AIX and system monitoring. Actually our application currently run production on jboss 5.1 in AIX 5.3. Please check below configuration & system settings. AIX system configuration OS Level 5.3.9.0 (oslevel -g) Physical Memory size 24GB (svmon -G) Page space 4GB (lsps -s) processors 3 cores, Processor Type: PowerPC_POWER6, Processor Clock Speed: 4704 MHz (prtconf | grep Processor) Java version JRE 1.6.0 IBM AIX build pap6460sr10fp1-20120321_01 (SR10 FP1) (java -fullversion) JBoss configuration JBoss 5.1/JBoss ESB 4.11 Hornetq messaging with consumer flow control java opts : -d64 -Xms2g -Xmx4g -XX:MaxPermSize=1024m Sometime we observe very strange behavior in the JBoss that freeze without any error logs. Also server log stop without any further trace. We also not able to get thread dump (kill -3) and its not generate at that point. (kill -3 xxxxx works in normal circumstances) Only option available for us was restart the jboss server and its seem all messages that were in queues during the freeze time process after restarting. We try tweak some of setting in JBoss hornetq, we though issue was there. Hornetq Stuck By Default. But we haven't any luck and also unable to isolate the issue in any point. We looking at tool like nmon for monitoring this but no clue is that good enough to do so. Please provide some point to investigate this issue. Thanks

  Read the article

• hadoop: port appears open locally but not remotelly

  - by miguel

  I am new to linux and hadoop and I am having the same issue as in this question. I think I understand what is causing it but I don't know how to solve it (Don't know what they mean by "Edit the Hadoop server's configuration file so that it includes its NIC's address."). The other post that they link says that the configuration files should refer to the machine's externally accessible host name. I think I got this right as every hadoop configuration file refers to "master" and the etc/hosts file lists the master by its private IP address. How can I solve this? Edit: I have 5 nodes: master, slavec, slaved, slavee and slavef all running debian. This is the hosts file in master: 127.0.0.1 master 10.0.1.201 slavec 10.0.1.202 slaved 10.0.1.203 slavee 10.0.1.204 slavef this is the hosts file in slavec (it looks similar in the other slaves): 10.0.1.200 master 127.0.0.1 slavec 10.0.1.202 slaved 10.0.1.203 slavee 10.0.1.204 slavef the masters file in master: master the slaves file in master: master slavec slaved slavee slavef the masters and slaves file in slavex has only one line: slavex

  Read the article

• I/O APIC on Virtualbox

  - by RidDeBakTiYar

  I'm trying to use the PIT to do APIC timer calibration, and I want to use the PIT through I/O APIC instead of PIC. On Bochs I get interrupts from the PIT at the asked frequency from the I/O APIC, while on Virtualbox I can't receive a single interrupt. It must be an I/O APIC configuration problem because as I unmask the first PIC entry, the IRQ fires. However that's not what I want. Can you imagine any possible condition that wouldn't make Virtualbox fire the IRQ? I'm not assuming single I/O APIC configuration (even though Virtualbox has only 1). I'm not assuming identity mappings between ISA IRQs and I/O APIC GSIs (using ACPI MADT table to get I/O APIC base address and Int override). I'm setting the Trigger Mode and Polarity bits correctly (on Virtualbox they are set as '00 - default' which means edge high right?). I'm putting the BSP APIC ID into the Destination field (using Physical destination) and vector 0x20. Being the BSP APIC ID 0 on Virtualbox, it ends up with 0x0000000000000020 written to the IOREDTBL. And, just in case I'm getting the wrong values from the Interrupt Override descriptor, I'm setting this value to all the IOREDTBL entries (I know this is very very bad, and it wont be kept as I understand what's going on). The only thing I didn't check out is Local APIC configuration. Actually I'm not writing any value to the BSP LAPIC. Just reading the APIC ID and using it to boot APs through IPIs. And obviously I'm setting bit 11 in the IA32_APIC_BASE MSR to enable the LAPIC. Any ideas? Thanks in advance.

  Read the article

• uWSGI cannot find "application" using Flask and Virtualenv

  - by skyler

  Using uWSGI to serve a simple wsgi app, (a simple "Hello, World") my configuration works, but when I try to run a Flask app, I get this in uWSGI's error logs: current working directory: /opt/python-env/coefficient/lib/python2.6/site-packages writing pidfile to /var/run/uwsgi.pid detected binary path: /opt/uwsgi/uwsgi setuid() to 497 your memory page size is 4096 bytes detected max file descriptor number: 1024 lock engine: pthread robust mutexes uwsgi socket 0 bound to TCP address 127.0.0.1:3031 fd 3 Python version: 2.6.6 (r266:84292, Jun 18 2012, 14:18:47) [GCC 4.4.6 20110731 (Red Hat 4.4.6-3)] Set PythonHome to /opt/python-env/coefficient/ *** Python threads support is disabled. You can enable it with --enable-threads *** Python main interpreter initialized at 0xbed3b0 your server socket listen backlog is limited to 100 connections *** Operational MODE: single process *** added /opt/python-env/coefficient/lib/python2.6/site-packages/ to pythonpath. unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) *** no app loaded. going in full dynamic mode *** *** uWSGI is running in multiple interpreter mode ***` Note in particular this part of the log: unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) **no app loaded. going in full dynamic mode** This is my Flask app: from flask import Flask app = Flask(__name__) @app.route("/") def hello(): return "Hello, World, from Flask!" Before I added my Virtualenv's pythonpath to my configuration file, I was getting an ImportError for Flask. I solved this though, I believe (I'm not receiving errors about it anymore) and here is my complete configuration file: uwsgi: #socket: /tmp/uwsgi.sock socket: 127.0.0.1:3031 daemonize: /var/log/uwsgi.log pidfile: /var/run/uwsgi.pid master: true vacuum: true #wsgi-file: /var/www/coefficient/coefficient.py wsgi-file: /var/www/coefficient/flask.py processes: 1 virtualenv: /opt/python-env/coefficient/ pythonpath: /opt/python-env/coefficient/lib/python2.6/site-packages This is how I start uWSGI, from an rc script: /opt/uwsgi/uwsgi --yaml /etc/uwsgi/conf.yaml --uid uwsgi And if I try to view the Flask program in a browser, I get this: **uWSGI Error** Python application not found Any help is appreciated.

  Read the article

• Apache 2.4, Ubuntu 12.04 Forbidden Errors

  - by tubaguy50035

  I just installed Apache 2.4 today, and I'm having some issues getting vhost configuration to work correctly. Below is the vhost conf <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /hosting/Client/site.com/www ServerName site.com ServerAlias www.site.com <Directory "/hosting/Client/site.com/www"> Options +Indexes +FollowSymLinks Order allow,deny Allow from all </Directory> DirectoryIndex index.html </VirtualHost> There is an index.html file in /hosting/Client/site.com/www. When I go to the site, I receive a 403 forbidden error. The www-data group is the group on the www folder, which I've already given all permissions (r/w/x). I'm really at a loss as to why this is happening. Any thoughts? If I remove the vhost and go straight to the IP address, I get the default, "It works!" page. So I know that it's working. The error log says "client denied by server configuration". apache2ctl -S dump: nick@server:~$ apache2ctl -S /usr/sbin/apache2ctl: 87: ulimit: error setting limit (Operation not permitted) VirtualHost configuration: *:80 is a NameVirtualHost default server site.com (/etc/apache2/sites-enabled/site.com.conf:1) port 80 namevhost site.com (/etc/apache2/sites-enabled/site.com.conf:1) alias www.site.com port 80 namevhost site.com (/etc/apache2/sites-enabled/site.com.conf:1) alias www.site.com ServerRoot: "/etc/apache2" Main DocumentRoot: "/var/www" Main ErrorLog: "/var/log/apache2/error.log" Mutex watchdog-callback: using_defaults Mutex default: dir="/var/lock/apache2" mechanism=fcntl Mutex mpm-accept: using_defaults PidFile: "/var/run/apache2.pid" Define: DUMP_VHOSTS Define: DUMP_RUN_CFG Define: ENALBLE_USR_LIB_CGI_BIN User: name="www-data" id=33 not_used Group: name="www-data" id=33 not_used Ouput of namei -mo /hosting/Client/site/www/index.html f: /hosting/Client/site.com/www/index.html drwxr-xr-x root root / drwxr-xr-x root root hosting drwxr-xr-x root root Client drwxr-xr-x nick www-data site.com drwxr-xr-x nick www-data www -rw-rwxr-x nick www-data index.html

  Read the article

• How do I properly configure a ZipInstaller .zic file?

  - by Iszi Rory or Isznti

  As of version 1.20, ZipInstaller is supposed to support the use of a configuration file to customize its installation options. Generally, all the options I want to use are available through the dialog so I really haven't bothered with the configuration file until now. The problem now is that certain tools, such as PsTools from Sysinternals, do not properly show their Product Name to ZipInstaller. ZipInstaller's dialog will let you customize the Start Menu folder and Program Files folder, but that still doesn't change the Product Name that it sees for the software. So, instead of having "PsTools" in my Add/Remove Programs, I get "Sysinternals Software". For some things, the situation is even more confusing. For example, the NIST SP 800-53 Reference Database Application gets installed as "FileMaker Pro Runtime". To rectify this, I've tried to use the aforementioned .zic configuration file. As I understand it, it's a basic INI file you create and put in the root of the ZIP file. ZipInstaller is supposed to read that file, and adjust its parameters accordingly. Mine looks like this: [install] ProductName=NIST_SP_800-53 ProductVersion=1.4.1 CompanyName=NIST Description=NIST_SP_800-53 InstallFolder=%zi.ProgramFiles%\%zi.ProductName% StartMenuFolder=%zi.CompanyName%\%zi.ProductName% I've named it `~zipinst~.zic and placed it in the root of the ZIP file, but when I run ZipInstaller it doesn't seem to recognize any of the information I've given it in the .zic file. What might I be doing wrong here?

  Read the article

• IIS7 error config and remote errors

  - by Kev

  Certain IIS7/7.5 500.19 configuration errors only render on a browser running on the local server. This appears to happen regardless of whether I set <httpErrors errorMode="Detailed" existingResponse="PassThrough" /> in the system.webServer section of a site's web.config file (or even globally for that matter). For example, I had a developer who reported that he was just getting the generic IIS7 500 error page: This was happening even though he had the following configured in his web.config: <configuration> <system.webServer> <httpErrors errorMode="Detailed" existingResponse="PassThrough" /> </system.webServer> </configuration> If I browse to the site on the server itself I see (some sensitive info redacted): Would the reason for this be that if the web.config has errors it therefore can't be parsed. Because it can't be parsed the local <httpErrors> setting doesn't get read and thus causes IIS to revert to default settings (i.e. DetailedLocalOnly)? Update: @LazyOne - suggested setting the above config at the server level which I already tried. This resulted in just raw 500 errors:

  Read the article

• Incorrect deployment of WSGI app to AWS using Elastic Beanstalk

  - by Dzmitry Zhaleznichenka

  cross-link to AWS forums I have developed a simple Python web service using WSGI and would like to deploy it to AWS cloud using Elastic Beanstalk. My problem is I cannot make all the options I specify in Elastic Beanstalk configuration to be correctly configured in the cloud. For deployment, I use Elastic Beanstalk CLI utility. I have run eb init command and set up the required parameters. After this, a directory named .elasticbeanstalk was created in my source tree. It has two config files that are used for deployment, namely config and optionsettings. The latter one among the other options contains the WSGI configuration that has to update /etc/httpd/conf.d/wsgi.conf at the instances. After some of my adjustments the file has the following settings: [aws:elasticbeanstalk:application:environment] DJANGO_SETTINGS_MODULE = PARAM1 = PARAM2 = PARAM4 = PARAM3 = PARAM5 = [aws:elasticbeanstalk:container:python] WSGIPath = handler.py NumProcesses = 2 StaticFiles = /static= NumThreads = 10 [aws:elasticbeanstalk:container:python:staticfiles] /static = static/ [aws:elasticbeanstalk:hostmanager] LogPublicationControl = false [aws:autoscaling:launchconfiguration] InstanceType = t1.micro EC2KeyName = zmicier-aws [aws:elasticbeanstalk:application] Application Healthcheck URL = [aws:autoscaling:asg] MaxSize = 10 MinSize = 1 Custom Availability Zones = [aws:elasticbeanstalk:monitoring] Automatically Terminate Unhealthy Instances = true [aws:elasticbeanstalk:sns:topics] Notification Endpoint = Notification Protocol = email It turns out that not all of these options are considered when I start the environment or update it. Thus, when I update NumThreads or NumProcesses, the respective parameters get changed in wsgi.conf as expected. But whatever I write to the WSGIPath and StaticFiles parameters, I'm not able to automatically change the respective values of wsgi.conf, they remain Alias /static /opt/python/current/app/ WSGIScriptAlias / /opt/python/current/app/application.py which drives me nuts. Moreover, when I deploy my application using git aws.push and having the following contents of .ebextensions/python.config file, neither of options I specify in it affects the deployment. option_settings: - namespace: aws:elasticbeanstalk:container:python option_name: WSGIPath value: mysite/wsgi.py - namespace: aws:elasticbeanstalk:container:python option_name: NumProcesses value: 5 - namespace: aws:elasticbeanstalk:container:python option_name: NumThreads value: 25 - namespace: aws:elasticbeanstalk:container:python:staticfiles option_name: /static/ value: app/static/ I wonder what I should do to force AWS use all the parameters I specify in the configuration, namely the WSGI Path and path to my static data.

  Read the article

• Installing Silverstripe on 000webhost.com (free web host)

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it just refreshes the install.php page. It doesn't even overwrite the .htaccess file. 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how. EDIT: I managed to get to the next page but now there is another warning which is stopping it installing: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701

  Read the article

• How to configure a Web.Config file to allow custom 404 handling while still displaying on-page 500 e

  - by Mark

  To customize 404 handling and based on the hosting company's suggestion, we are currently using the following web.config setup. However, we quickly realized that with this configuration, any page error (500 error) are also getting redirected to this custom error page. How can I modify this config file so we can continue to handle 404 with custom file while still able to view on-page error? <?xml version="1.0" encoding="utf-8" ?> <configuration> <system.webServer> <httpErrors errorMode="DetailedLocalOnly" defaultPath="/Custom404.html" defaultResponseMode="ExecuteURL"> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="/Custom404.html" responseMode="ExecuteURL" /> </httpErrors> </system.webServer> <system.web> <customErrors mode="On"> <error statusCode="404" redirect="/Custom404.html" /> </customErrors> </system.web> </configuration>

  Read the article

• Installing SilverStripe on 000webhost.com (Free web host)?

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it brings me to a page with the following errors: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how.

  Read the article

• Wireless internet connection connects but internet does not work (no packets received). Wired does.

  - by Rodney

  When I connect my PC via ethernet cable to my ADSL router it works fine. When I connect via Wireless it connects and the internet will work for a random amount of time and then stop working. It stays connected with a strong signal but no packets are received. My laptop/iphone are right next to it and wireless works fine. If I open the Wireless USB status, it says it is connected to my SSID with full strength (54 mps - I am 3 meteres away from my router) and the activty shows as Packets 594 SENT and 105 RECEIVED (this goes up VERY slowly) I have tried the following: Turned off anitvirus and firewall completely. Tested the wifi signal- I am writing this on my laptop which is next to my PC and also has full wifi strength. Tried a different wireless adapter - I dug out an old PCI wireless card - it does the exact same thing. Compared all wireless settings to my laptop. I can ping google.com and it replies (sometimes with packet loss) When I reboot the PC it will connect for a minute or two (random time) and then just stops again. I tried Firefox, IE etc. no joy I have updated all latest versions (Netgear WG111v2) and drivers Checked Event Log - nothing unusual Ping the router (and even connect as admin for the few minutes when the internet does work) Changed the MTU down to 1200 using DrTCP Checked Device Manager for conflicts - none. I ping the router from the PC (192.168.0.10 - 192.168.0.1) and it replies with 4 packets. BUT, on my router admin page (which I access via http on my laptop wirelessly) - if I ping 192.168.0.10 all packets timeout (pinging my laptop 192.168.0.12 works fine) My router admin page shows the leased IP address for 192.168.0.10 (ie it is definitely talking to the router initially) Now I am out of ideas - please help. I think it is an OS/Software issue as I have tried 2 different wireless adapaters (PCI and USB) with the same result but all other wireless devices work fine around mine). It's not the firewall. It is getting assigned an IP address correctly (my PC gets 192.168.0.10, my laptop is .12) It is assigned by DHCP. As soon as I plug in the ethernet cable it all works fine. Repairing the adapter sometimes helps but it will always stop working after a random time. The wireless adapter always shows as connected with Excellent signal but the internet does not work. I am running Windows XP SP3 and have tried a Netgear WG111v2 USB adapter. Thanks in advance! UPDATE: The internet seems to be working, it is just either sending packets too small or slow to work (some small pages load bits of them very slowly but then hang). XP seems to have a networking diagnostic app - here is the output: Last diagnostic run time: 08/30/10 08:16:38 IP Configuration Diagnostic Invalid IP address info Valid IP address detected: 192.168.0.10 IP Layer Diagnostic Corrupted IP routing table info The default route is valid info The loopback route is valid info The local host route is valid info The local subnet route is valid Invalid ARP cache entries action The ARP cache has been flushed Gateway Diagnostic Gateway info The following proxy configuration is being used by IE: Automatically Detect Settings:Disabled Automatic Configuration Script: Proxy Server: Proxy Bypass list: info This computer has the following default gateway entry(ies): 192.168.0.1 info This computer has the following IP address(es): 192.168.0.10 info The default gateway is in the same subnet as this computer info The default gateway entry is a valid unicast address info The default gateway address was resolved via ARP in 1 try(ies) info The default gateway was reached via ICMP Ping in 1 try(ies) info TCP port 80 on host 65.55.12.249 was successfully reached info The Internet host www.microsoft.com was successfully reached info The default gateway is OK DNS Client Diagnostic DNS - Not a home user scenario info Using Web Proxy: no info Resolving name ok for (www.microsoft.com): yes No DNS servers DNS failure HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Passive): Successfully connected to ftp.microsoft.com. info HTTP: Successfully connected to www.microsoft.com. warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out error Could not make an HTTPS connection. info Redirecting user to support call WinSock Diagnostic WinSock status info All base service provider entries are present in the Winsock catalog. info The Winsock Service provider chains are valid. info Provider entry MSAFD Tcpip [TCP/IP] passed the loopback communication test. info Provider entry MSAFD Tcpip [UDP/IP] passed the loopback communication test. info Provider entry RSVP UDP Service Provider passed the loopback communication test. info Provider entry RSVP TCP Service Provider passed the loopback communication test. info Connectivity is valid for all Winsock service providers. Wireless Diagnostic Wireless - Service disabled Wireless - User SSID action User input required: Specify network name or SSID Wireless - First time setup info The Wireless Network name (SSID) to which the user would like to connect = RodSof Wifi. Wireless - Radio off info Valid IP address detected: 192.168.0.10 Wireless - Out of range Wireless - Hardware issue Wireless - Novice user Wireless - Ad-hoc network Wireless - Less preferred Wireless - 802.1x enabled Wireless - Configuration mismatch Wireless - Low SNR Network Adapter Diagnostic Network location detection info Using home Internet connection Network adapter identification info Network connection: Name=Local Area Connection 2, Device=Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC, MediaType=LAN, SubMediaType=LAN info Network connection: Name=Wireless USB, Device=NETGEAR WG111v2 54Mbps Wireless USB 2.0 Adapter, MediaType=LAN, SubMediaType=WIRELESS info Both Ethernet and Wireless connections available, prompting user for selection action User input required: Select network connection info Wireless connection selected Network adapter status info Network connection status: Connected HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Active): Successfully connected to ftp.microsoft.com. warn HTTP: Error 12007 connecting to www.microsoft.com: The server name or address could not be resolved warn HTTP: Error 12002 connecting to www.hotmail.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out error Could not make an HTTP connection. error Could not make an HTTPS connection.

  Read the article

• Wrong Outlook anywhere settings

  - by Ken Guru

  Hey all I wanted to enable NTLM authentication on OutlookAnywhere, and after doing the command Set-OutlookAnywhere -IISAuthenticationMethods Basic,NTLM, my settings got changed. This is a dump before I run the command: [PS] C:\Windows\system32Get-OutlookAnywhere ServerName : EXCAS01 SSLOffloading : False ExternalHostname : ClientAuthenticationMethod : Basic IISAuthenticationMethods : {Basic} MetabasePath : IIS:///W3SVC/1/ROOT/Rpc Path : C:\Windows\System32\RpcProxy Server : EXCAS01 AdminDisplayName : ExchangeVersion : 0.1 (8.0.535.0) Name : Rpc (Default Web Site) DistinguishedName : CN=Rpc (Default Web Site),CN=HTTP,CN=Protocols,CN= EXCAS01,CN=Servers,CN=Exchange Administrative Grou p (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=Fi rst Organization,CN=Microsoft Exchange,CN=Services ,CN=Configuration,DC=asp,DC=ssc,DC=no Identity : EXCAS01\Rpc (Default Web Site) Guid : 289b4865-caf1-4412-95ee-6fb0dff55e8b ObjectCategory : asp.ssc.no/Configuration/Schema/ms-Exch-Rpc-Http-V irtual-Directory ObjectClass : {top, msExchVirtualDirectory, msExchRpcHttpVirtual Directory} WhenChanged : 05.01.2011 16:59:55 WhenCreated : 27.11.2009 11:20:12 OriginatingServer : IsValid : True Noticde the settings for "Name", "DistinguishedName", and "Identity". After I run the command, I ended up with this: [PS] C:\Windows\system32Get-OutlookAnywhere ServerName : EXCAS01 SSLOffloading : False ExternalHostname : ClientAuthenticationMethod : Basic IISAuthenticationMethods : {Basic, Ntlm} MetabasePath : IIS:///W3SVC/1/ROOT/Rpc Path : C:\Windows\System32\RpcProxy Server : EXCAS01 AdminDisplayName : ExchangeVersion : 0.1 (8.0.535.0) Name : EXCAS01 DistinguishedName : CN=EXCAS01,CN=HTTP,CN=Protocols,CN=EXCAS01,CN=Serv ers,CN=Exchange Administrative Group (FYDIBOHF23SP DLT),CN=Administrative Groups,CN=First Organizatio n,CN=Microsoft Exchange,CN=Services,CN=Configurati on,DC=asp,DC=ssc,DC=no Identity : EXCAS01\EXCAS01 Guid : 289b4865-caf1-4412-95ee-6fb0dff55e8b ObjectCategory : asp.ssc.no/Configuration/Schema/ms-Exch-Rpc-Http-V irtual-Directory ObjectClass : {top, msExchVirtualDirectory, msExchRpcHttpVirtual Directory} WhenChanged : 06.01.2011 09:43:50 WhenCreated : 27.11.2009 11:20:12 OriginatingServer : ASP-DC-2. IsValid : True Now, the "Name", "DistinguishedName" and "Identity" has changed, and when I try to change it back by running "Set-OutlookAnywhere -Identity "EXCAS01\Rpc (Default Web Site)", I get the following error: [PS] C:\Windows\system32Set-OutlookAnywhere -Identity "EXCAS01\Rpc (Default Web Site)" Set-OutlookAnywhere : The operation could not be performed because object 'EXCA S01\Rpc (Default Web Site)' could not be found on domain controller 'ASP-DC-2.'. Remember, the RPC over HTTP works fine with Basic authentication (even with the wrong settings), but NTLM still doesnt work. How do I change back the settings?

  Read the article

• Cisco Catalyst 4500 Policy Based Routing

  - by Logan

  In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

  Read the article

• emails not sending from CentOS 5.6 VM on Win7 via PHP code

  - by crmpicco

  I am experiencing an issue where my CentOS 5.6 (Final) VM running on Windows 7 has stopped sending emails from my PHP code. I'm confident this isn't a coding issue as I have the exact same code running in my office and emails send correctly from there, hence why I believe this to be a networking/configuration issue. In my /etc/hosts/ file on my VM I have the following: 127.0.0.1 localhost.localdomain localhost 192.168.0.9 crmpicco.co.uk m.crmpicco.co.uk dev53.localdomain When I run setup on my VM the DNS configuration is set to dev53.localdomain and my Primary DNS is 192.168.0.1. In My /var/log/maillog files I see a lot of this sort of thing: Nov 19 14:36:58 dev53 sendmail[21696]: qAJEawI7021696: from=<[email protected]>, size=12858, class=0, nrcpts=1, msgid=<1353335817.9103820024efb30b451d006dc4ab3370@PHPMAILSERVER>, proto=ESMTP, daemon=MTA, relay=localhost.localdomain [127.0.0.1] Nov 19 14:36:58 dev53 sendmail[21693]: qAJEawvd021693: [email protected], [email protected] (48/48), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=42681, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (qAJEawI7021696 Message accepted for delivery) Nov 19 14:36:59 dev53 sendmail[21698]: qAJEawI7021696: to=<[email protected]>, delay=00:00:01, xdelay=00:00:01, mailer=esmtp, pri=132858, relay=mailserver.fletcher.co.uk. [213.171.216.114], dsn=5.0.0, stat=Service unavailable Is this likely to be a configuration issue?

  Read the article

• How to configure a shortcut for an SSH connection through a SSH tunnel

  - by Simone Carletti

  My company production servers (FOO, BAR...) are located behind two gateway servers (A, B). In order to connect to server FOO, I have to open a ssh connection with server A or B with my username JOHNDOE, then from A (or B) I can access any production server opening a SSH connection with a standard username (let's call it WEBBY). So, each time I have to do something like: ssh johndoe@a ... ssh webby@foo ... # now I can work on the server As you can imagine, this is a hassle when I need to use scp or if I need to quickly open multiple connections. I have configured a ssh key and also I'm using .ssh/config for some shortcuts. I was wondering if I can create some kind of ssh configuration in order to type ssh foo and let SSH open/forward all the connections for me. Is it possible? Edit womble's answer is exactly what I was looking for but it seems right now I can't use netcat because it's not installed on the gateway server. weppos:~ weppos$ ssh foo -vv OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /Users/xyz/.ssh/config debug1: Applying options for foo debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Executing proxy command: exec ssh a nc -w 3 foo 22 debug1: permanently_drop_suid: 501 debug1: identity file /Users/xyz/.ssh/identity type -1 debug2: key_type_from_name: unknown key type '-----BEGIN' debug2: key_type_from_name: unknown key type 'Proc-Type:' debug2: key_type_from_name: unknown key type 'DEK-Info:' debug2: key_type_from_name: unknown key type '-----END' debug1: identity file /Users/xyz/.ssh/id_rsa type 1 debug2: key_type_from_name: unknown key type '-----BEGIN' debug2: key_type_from_name: unknown key type 'Proc-Type:' debug2: key_type_from_name: unknown key type 'DEK-Info:' debug2: key_type_from_name: unknown key type '-----END' debug1: identity file /Users/xyz/.ssh/id_dsa type 2 bash: nc: command not found ssh_exchange_identification: Connection closed by remote host

  Read the article

• Utility to LOGICALLY compare two xml files?

  - by Matthew

  Right now we are attempting to build golden configurations for our environment. One piece of software that we use relies on large XML files to contain the bulk of its configuration. We want tot ake our lab environment, catalog it as our "golden configuration" and then be able to audit against that configuration in the future. Since diff is bytewise comparison and NOT logical comparison, we can't use it to compare files in this case (XML is unordered, so it won't work). What I am looking for is something that can parse the two XML files, and compare them element by element. So far we have yet to find any utilities that can do this. OS doesn't matter, I can do it on anything where it will work. The preference is something off the shelf. Any ideas? Edit: One issue we have run into is one vendor's config files will occasionally mention the same element several times, each time with different attributes. Whatever diff utility we use would need to be able to identify either the set of attributes or identify them all as part of one element. Tall order :)

  Read the article

• Apache ScriptAlias and access error?

  - by Parhs

  First of all after much pain i figured out how to make it work in Apache 2.4 windowz. Here is my configuration that seems to work successfully for git clone and push and everything. Problem First of all my configuration works. There is a "Require all denied" at / directory. I want only git functionality and nothing else. Example Request from a git client 192.168.100.252 - - [07/Oct/2012:04:44:51 +0300] "GET /git/simple/info/refs?service=git-upload-pack HTTP/1.1" 200 264` Error caused by that Request [Sun Oct 07 04:44:51.903334 2012] [authz_core:error] [pid 6988:tid 956] [client 192.168.100.252:13493] AH01630: client denied by server configuration: C:/git-server/web/simple There isnt any error at gitclient everything works fine but i get this at error log. Is there any solution for this error to not appear?I worry about log size. <VirtualHost *:80> DocumentRoot "C:\git-server\web" ServerName git.****censored**** DirectoryIndex index.php SetEnv GIT_PROJECT_ROOT c:/git-server/repositories SetEnv GIT_HTTP_EXPORT_ALL SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER ScriptAlias /git/ "C:/Program Files (x86)/Git/libexec/git-core/git-http-backend.exe/" <LocationMatch "^/.*/git-receive-pack$"> Options +ExecCGI AuthType Basic AuthName intranet AuthUserFile "C:/git-server/config/users" Require valid-user </LocationMatch> <Directory /> Options All Require all denied </Directory> <Directory "C:\Program Files (x86)\Git\libexec\git-core"> Options +ExecCGI Options All Require all granted </Directory> </VirtualHost>

  Read the article

• MySQL extension of PHP not working

  - by Víctor

  In a Debian server, and after intallation and removal of SquirrelMail (with some downgrade and upgrade of php5, mysql...) the MySQL extension of PHP has stopped working. I have php5-mysql installed, and when I try to connect to a database through php-cli, i connect successfully, but when I try to connect from a web served by Apache I cannot connect. This script, run by php5-cli: echo phpinfo(); $link = mysql_connect('localhost', 'user, 'password'); if (!$link) { die('Could not connect: ' . mysql_error()); } echo 'Connected successfully'; mysql_close($link); Prints the phpinfo, which includes "/etc/php5/cli/conf.d/mysql.ini", and also the MySQL section with all the configuration: SOCKET, LIBS... And then it prints "Connectes successfully". But when run by apache accessed by web browser, it displays the phpinfo, which includes "/etc/php5/apache2/conf.d/mysql.ini", but has the MySQL section missing, and the script dies printing "Fatal error: Call to undefined function mysql_connect()". Note that both "/etc/php5/cli/conf.d/mysql.ini" and "/etc/php5/apache2/conf.d/mysql.ini" are in fact the same configuration, because I have in debian the structure: /etc/php5/apache2 /etc/php5/cgi /etc/php5/cli /etc/php5/conf.d And both point at the same directory: /etc/php5/apache2/conf.d -> ../conf.d /etc/php5/cli -> ../conf.d Where /etc/php5/conf.d/mysql.ini consists of one line: extension=mysql.so So my question is: why is the MySQL extension for PHP not working if I have the configuration included just in the same way as in php-cli, which is working? Thanks a lot!

  Read the article

• Very long (>300s) request processing time on Apache Server serving static content from particular IP

  - by Ron Bieber

  We are running an Apache 2.2 server for a very large web site. Over the past few months we have been having some users reporting slow response times, while others (including our resources, both on the internal network and our home networks) do not see any degradation in performance. After a ton of investigation, we finally found a "Deny from none" statement in our configuration that was causing reverse DNS lookups (which were timing out) that solved the bulk of our issues, but we still have some customers that we are seeing in the Apache logs (using %D in the log format) with request processing times of 300s for images, css, javascript and other static content. We've checked all Deny / Allow statements for reoccurrence of "none", as well as all other things we know of that would cause reverse DNS lookups (such as using "REMOTE_HOST" in rewrite rules, using %a instead of %h in our log format configuration) as well as verified that HostnameLookups is set to "Off". As an aside, we've also validated that reverse DNS lookups for folks having this problem do not time out - so I'm fairly certain DNS is not an issue in this case. I've run out of ideas. Are there any Apache configuration scenarios that someone can point me to that I might be missing that would cause request times for static content to take so long only for certain users? Thank you in advance.

  Read the article

< Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >