Search Results

Search found 8228 results on 330 pages for 'card reader'.

Page 189/330 | < Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >

• Broadcom BCM4313 working, but terribly slow

  - by Ataraxio Panzetta

  Hi all, I've installed ubuntu on a Asus 1015 netbook. Everything worked out of the box except for the Wireless adapter, which i had to install with the Additional Drivers application. It apparently installed fine and connects to our wireless network, but it only works at a "funny" speed range that goes from 367Bytes to a peak of 3Kb in its best moments. I know for sure the problem is neither the network nor the hardware. Network speeds are normal under windows on this laptop and in other computers with ubuntu aswell. lspci says the card is a BCM4313 model, but the Addittional Drivers Manager says these packecege contains Broadcom 802.11 Linux STA wireless driverfor use with Broadcom's BCM4311-, BCM4312-, BCM4321-, and BCM4322 based hardware seems like it installed the wrong driver... Is there anything I can do? I'm not concerned about compiling the driver or stuff like that, but I'm not sure on where to start... any help or guidance will be very, very appreciated.

  Read the article

• terminal won't show in failsafex

  - by Samir Desai

  so after recently reinstalling some drivers I came across the issue detailed in this post How to fix "The system is running in low-graphics mode" error? I run 12.04 on my HP laptop with an Nvidia card. I went to GRUB and loaded failsafex to have the exact same problem described in the response up there, I then attempted to load the terminal, however when I do try and load the terminal I just get a blank screen and nothing else, is there any other easier way to access the terminal. I am quite new to Ubuntu.

  Read the article

• Purple start screen - no splash screen

  - by Peter

  After installing Ubuntu 11.10 on a new computer everything worked fine for a few weeks and now suddenly when starting up Ubuntu I get a blank purple screen with no "ubuntu" splash and the 5 dots but the system does start up. What has happened to loose the ubuntu splash screen? Also, I've checked in the grub startup and it has "quiet splash" in the linux line. I have an ATI radeon 5450 graphics card which needed nomodeset to be added to the grub line when booting for the first time off the install CD but now this line has disappeared from the grub startup. Can anyone help. Thanks

  Read the article

• Broadcom 4365 wireless driver with 3.4 / 3.5 kernel

  - by zaid

  I used this package to install the driver on 3.2 Kernel and it was working perfectly. Unfortunately the system used to freeze randomly with 3.2 kernel so I installed 3.4 kernel, now there is no freezing, the only problem is that my wifi card is not working, I tried to re-install the package, but didn't work. I can see the driver in the "additional drivers" and it say that it is active, but when I execute iwconfig it doesn't show up. I've even tried ndiswraper and that didn't work either. my lspci: 01:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01)

  Read the article

• Probelm with ATI catalyst drivers in ubuntu 13.10

  - by Raja

  Recently I've installed dual boot ubuntu 13.10 alongside windows 8. My Laptop is Dell Inspiron 15, with AMD Radeon HD 7670 Video Card. Without fglrx my battery is draining to 1:30 hrs from 3:30hrs (In Ubuntu 13.04 but very slow booting ) so I installed fglrx using What is the correct way to install ATI Catalyst Video Drivers (fglrx)? But the problem is as you all know, Black Screen after logging into ubuntu. Tried so many solutions for this like reinstalling unity , ubuntu-desktop , compizconfig , etc.. but none helped except removing fglrx* completely. (But I need them very badly due to battery) Assuming that all hope is lost., Posting here as a final try.! Will be highly greatfull for those who helped :) PS : For those who think this question is a duplicate., Though the question may be a duplicate, but the answer is not! (so give me a assured solution for this problem before flagging this as duplicate., Kindly understand my frustation) Thank You !

  Read the article

• Unable to mount samsung galaxy S3 via USB

  - by dez93_2000

  Connecting as either MTP or PTP: neither allows one to see pictures saved as default by phone camera to DCIM folder on external SD card. Similar problems with previous models (e.g. S2) were solvable by 'usb utilities' in wireless & networking settings, but this is no longer present. Other suggestions have mentioned uninstalling various libraries... but i don't wanna just start cutting stuff without knowing it'll help. Any thoughts? Seems like a pretty epic fail from google & samsung. There's not even a linux section on the relevant google site... despite android's usb driver being part of the linux kernel which powers android. Boo!

  Read the article

• Input Signal Out of Range 1920x1080

  - by Zach

  I've recently installed Ubuntu 12.04 on my computer. Now, every time I boot and when I shut down, my monitor goes blank and says "Input Signal Out of Range - Change Setting to 1920x1080 60Hz." Once the computer gets to the login screen, it's okay again. This problem also happens when I try to open any 3d app. My graphics card is NVIDIA GEforce 6150 SE. I tried updating the drivers, but it broke everything and I had to reinstall Ubuntu. Any help?

  Read the article

• How do GameEngines stop Pixel Seams appearing in adjacent mesh boundaries due to FP imprecision?

  - by ufomorace

  Graphics cards are mathematically imprecise. So when some meshes are joined by their borders, the graphics card often makes mistakes and decides that some pixels at the seam represent neither object, and unwanted pixels appear. It's a natural behaviour on all graphics cards. How are such worries avoided in Pro Games? Batching? Shaders? Different tangent vectors? Merging? Overlaping seams? Dark backgrounds? Extra vertices at borders? Z precision? Camera distance tweaks? Screencap of a fix that ended up not working:

  Read the article

• Multiple Monitors using nvidia-prime or bumblebee on Ubuntu 13.10

  - by user205626

  I've been unable to get multiple monitors to work with Ubuntu 13.10 using nvidia-prime or bumblebee. Could someone point me in the right direction? With nvidia-prime, I've tried the xorg.conf here http://us.download.nvidia.com/XFree86/Linux-x86/319.12/README/randr14.html, but I boot into "low graphics" mode and have to revert to get a desktop back. Any suggestions would be appreciated. Thanks. Edit: I've given up on nvidia-prime; I missed the fact that it never turns off the discrete card... So, I'm back to trying to get VIRTUAL displays working with Bumblebee.

  Read the article

• Wifi won't work without ethernet (Ubuntu 12.04)

  - by alok

  I have a strange problem. I am running Ubuntu 12.04 on a Dell Studio 1558 laptop. I'm usually unable to access Wifi (I have a BCM43224 wireless card with the STA proprietary driver installed.) So I have to unplug the ethernet cable from my Wifi router and stick it into my laptop's ethernet port to access the Internet. But when I stick the cable back into the Wifi router and try connecting to Wifi, Wifi inexplicably starts working. How can I get Wifi to work all the time without having to 'jumpstart' it with an ethernet connection?

  Read the article

• Dual monitor, with a low resolution projector

  - by user900978

  I need to show a presentaion to a conference tomorrow. Today I tryed my Ubuntu 10.04 with the projector. My notebook has a resolution of 1440x960, the projector seems to have a really lower resolution. However, thanks to nvidia-settings I configured my video card (a nvidia 9800), it works with other display, but not with the projector. I found the projector, configured as Twin-view, resolution Auto and pressed on Apply, then "Save to x Configuration". On projector is visualized just a quarter of my notebook display. I tryed also to reduce my resolution and to change the resolution of projector, but I obtained no better results. How can I Solve it? On windows all goes well, but I need Ubuntu for personal reasons. Thanks in advance

  Read the article

• Shopping cart for service providers?

  - by uos??

  From my limited exposure, it seems to me that most shopping cart/eCommerce platforms are specifically for products-based retailers. On several occasions now, I've been asked about ecommerce solutions for service providers. That is, it's basically just a single product with payment but no shipping, and highly configurable "product". Any recommendations for a cost-efficient solution (high feature coverage) for such a web platform? Requirements: .NET No/suppressed product catalog A service customization selection form Payment (probably PayPal with accountless credit card processing) Guest purchases (no site account required) Email confirmation Customer service -facing control panel It's hard to search for such a product because I get "web service based ecommerce software" and so on clouding up the results.

  Read the article

• How To Install and Use ADB, the Android Debug Bridge Utility

  - by Chris Hoffman

  ADB, Android Debug Bridge, is a command-line utility included with Google’s Android SDK. ADB can control your device over USB from a computer, copy files back and forth, install and uninstall apps, run shell commands, and more. We’ve covered some other tricks that require ADB in the past, including backing up and restoring your smartphone or tablet and installing Android apps to your SD card by default. ADB is used for a variety of geeky Android tricks. Image Credit: LAI Ryanne on Flickr HTG Explains: How Antivirus Software Works HTG Explains: Why Deleted Files Can Be Recovered and How You Can Prevent It HTG Explains: What Are the Sys Rq, Scroll Lock, and Pause/Break Keys on My Keyboard?

  Read the article

• Wireless speed drops over time and doesn't get up if not reconnected

  - by Vili Lehto

  I am using Ubuntu 12.10 64bit and I have a Asus PCE-N15 wireless card(in PCI-E slot). The problem is that first when I connect to my WiFi network the speed is just fine, and actually my link speed never drops, it shows a solid 150mb/s+ link speed and good signal. But the download and upload speeds drop dramatically after couple minutes of use and I have to reconnect to fix this. Network is type IEEE 802.11bgn and uses WPA2/AES encryption. I don't have similar problems on the windows side, and the network is working fine on every other device. iwconfig shows this: wlan0 IEEE 802.11bgn ESSID:"WLAN-AP" Mode:Managed Frequency:2.412 GHz Access Point: 00:1E:AB:05:EF:31 Bit Rate=300 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Encryption key:off Power Management:off Link Quality=61/70 Signal level=-49 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:2 Missed beacon:0 So the question is: Is there a way to fix this? Thanks in advance.

  Read the article

• Bootable usb stick not boots

  - by Pavaroti Luciano

  i have problem. My bootable usb stick not boots any linux distribution.. it just stop at BIOS, like before turning on OS, but it does nothing. Windows xp/7/8.1 installs boots perfectly. It stopped booting every linux dist. after windows 8.1 installation. Later i deleted windows 8.1 and installed windows 7, and now i want to install ubuntu from usb, but i cant(From disk every linuxOS boots perfectly but not from usb) My computer now is like ~7years old. Specs: CPU: AMD Athlon 64 X2 5000+ Motherboard: GIGABYTE GA-M56S-S3 Video card: Nvidia n210 EDIT: It boots on my other laptop..its bootable, but from this.. NOpe, only windows installs

  Read the article

• All video players display black screen.

  - by Dennis

  I'm working in 10.04 Lucid. All my video players (Movie Player and VLC) and the preview windows in editors (OpenShot and Pitivi) will only display a black screen when playing a video. The sound is fine and the videos work fine on other computers. I have tried multiple formats from varying sources .MOV taken from old ffmpeg projects, .AVI straight from a camera, .MP4 using h.264 from OpenShot on another system, .OGV from a gtk-recordmydesktop session on this very computer. I even get a pure black screen in the viewer when starting a remote session in VNC. This box has a GeForce 8400 GS using the Nvidia drivers in case it may be a card problem or setting.

  Read the article

• Brightness not working; HP Pavilion Dv6; ATI Radeon HD6770M

  - by Yogesh Dhamija

  I am new to Ubuntu, but so far I am loving it. I was always unable to change my brightness since I installed Ubuntu, but I figured that installing the latest ATI driver for my graphics card would work. I did, but I still can't change the brightness. The slider goes up and down, but the brightness stays the same (on full). I have switchable graphics, an ATI Radeon HD 6770M, and an Intel integrated GPU. Since I am new to Linux, I am not familiar with terminal, so you will have to spell everything out for me, including if you need more information and how to get it. Thanks.

  Read the article

• Install AMDCONFIG on Ubuntu driver

  - by Nick Bailuc

  In 12.04 I used the official driver downloaded from amd.com which came with amdconfig but now in 14.04 the official driver is buggy so I just use the Ubuntu Official Drivers which works even better because they beefed up the original driver. The Ubuntu driver doesnt come with the terminal command amdconfig which allowed me to tweak/overclock my graphics card. How can I install it without having to install the original AMD driver? Additional Information: -I only use x.org drivers becuase it's opensource therefore more stable rather than the proprietary fglrx driver -I do not use procrams like amdoverdrivectrl or atioverclock because they are not as stable and advanced as the terminal command

  Read the article

• Booting briefly shows CLI login and then black

  - by lepusfelix

  When I boot to Ubuntu on my dualboot system, it appears to boot normally, up to the point when I would normally expect to see the lightDM graphical login screen. However, I see a CLI login screen, which I assume is tty1. Before I get a chance to actually login to it, though, it drops to a black screen with a flashing cursor. Pressing ctrl+alt+f1 does nothing. When I hit the power button on the laptop, I see the usual scrolling text as Ubuntu shuts down. I know that this is related to me having installed the proprietary ATI drivers for the video card. Purging the drivers gave me back a GUI, but unfortunately no working desktop environment, and switching to the mesa drivers returned me to the black screen issue. The only way I can get a stable working CLI is through booting to advanced options and choosing a root shell prompt, as even the failsafe X session doesn't function for me.

  Read the article

• Developing a DVR software using a hardware KIT

  - by Leron

  I'm currently thinking about a project for my masters degree graduation. I start researching for options to make my own video streaming software based on a premade hardware kit having not much knowledge about what I'll exactly need that will match my needs. My search led me to the DVR (Digital Video Recorder) cards which seems to be the closest to what I need, but still I can't find out a few basic things so I decide to ask for them here. Currently I haven't find a lot of manufacturers that offers such kits so where I can look and have some options to choose from? There are a lot of DVR products on the market but they already have a software written for them and even if I buy one they just don't give any documentation or sdk's so buying such is not an option I need a DVR card made exactly for software programers and not end users. Are there a preferred manufacturers that provide such kind of devices with good and developer-friendly documentation? Also - I prefer to do all this with Java, is this an option (I think I will make it with .NET too but really prefer Java as a language of choice)

  Read the article

• Apple Cinema Display 23" and grub

  - by Joshua Pruitt

  As per the title, I'm running my display on an older 23" Apple Cinema Display (because I still love it, darn it). I'm pushing it with an ATI Radeon DVI dual-link PCIe card. It works just fine, except GRUB doesn't seem able to push out the 1920x1200 pixel resolution needed in order to show me a boot menu! So..., I keep a smaller second monitor connected as the primary display so that I can see the boot menu and boot the system (I don't use that display once booted). This is a goofy work-around, and I'd like to just use my single display exclusively to boot the machine. I found some grub codes for higher resolutions, but not for 1920x1200. Is it capable of this? Did I just miss it? Thanks in advance!!!

  Read the article

• Can I hook my xbox up to my Ubuntu PC

  - by Anonymous John

  My old xbox 360 won't eject disks, it makes a sound,but won't open. I want to play games, so I think I could hook it up to my PC running Ubuntu 13.10 64-bit and maybe I could use my PC's DVD drive. Can this work at all, or am I just crazy? There is an HDMI port on the back of my graphics card. If I can't do that, is there any software for Ubuntu that can rip the game off of a CD and put it on a flash drive? I have heard xbmcbuntu works great for gaming, but it doesn't work with my PC.

  Read the article

• Is the wireless driver from Live USB different from the standard install?

  - by Rafael Magalhães

  Linux newbie here. I've been trying to use Ubuntu (x64) as my main OS since 11.10, but my wireless connection on it has been very unstable, droping every other 5-10 mins. For this reason I see myself forced to use Windows 7 (dual booting), where connection works flawlessly -- which really bothers me. My card is an Atheros 9k, which claims a reasonable amount of wireless complaints on Ubuntu forums. I've tried every suggestion given on past questions to this site but to no avail. However, while running Ubuntu Live USB for some of the tests, I noticed that my wireless connection never failed on it and wondered if its network configuration differs from the one on the default Ubuntu install. If this is the case, how could I reproduce the Live USB network environment on my hard drive install?

  Read the article

• What is this chargeback scam from eBooks bought on my website?

  - by Dan Friedman

  We have a scammer that is buying our e-Books and then performing chargebacks. Our e-Books don't have DRM, so if they wanted to resell them, they would only need to buy each book once. But instead, they keep buying the same books over and over again and then performing hundreds of chargebacks. We have created some additional rules in our fraud protection tools to block certain aspects, even though all the info looks legit, and are hopeful this will slow them down. But my question is: What is the scam? If they aren't getting any product and they only get chargebacks for something they already purchased, then they can't get additional money from the credit card company, so then what's their motivation?

  Read the article

• How should I interpret these DirectX Caps Viewer values?

  - by tobi

  Briefly asking - what do the nodes mean and what the difference is between them in DirectX Caps Viewer? DXGI Devices Direct3D9 Devices DirectDraw Devices The most interesting for me is 1 vs 2. In the Direct3D9 Devices under HAL node I can see that my GeForce 8800GT supports PixelShaderVersion 3.0. However, under DXGI Devices I have DX 10, DX 10.1 and DX 11 having Shader model 4.0 (actually why DX 11? My card is not compatible with DX 11). I am implementing a DX 11 application (including d3d11.h) with shaders compiled in 4.0 version, so I can clearly see that 4.0 is supported. What is the difference between 1 and 2? Could you give me some theory behind the nodes?

  Read the article

< Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >