Search Results

Search found 13476 results on 540 pages for 'non lazy ptr'.

Page 189/540 | < Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >

• Installation of Active Directory on separate VM from DNS does not entierly work - not sure why

  - by René Kåbis

  Not sure what I am doing wrong here. I have a moderately midrange server (16 cores, 2Ghz, 32GB ECC REG RAM, 6TB storage, nothing too extreme) where I am running Hyper-V (Server 2012 R2 Enterprise) in order to provision virtual machines. So why an AD separate from DNS? I want redundancy. I want to be able to move VMs and back them up individually and not have too many services on any one VM. I have already provisioned a VM with DNS, and have set it up right -- essentially, I have: Set up Static IP’s for everyone involved. Installed the DNS service on the DNS VM. Created a forward lookup zone and a reverse lookup zone (primary zone) xyz.ca Configured the zones to use nonsecure and secure dynamic updates (i will change this to secure later after the domain controller is online). Created a A record for the DC in the forward lookup zone (and a reverse ptr) Changed DC’s DNS server (network settings) to the new DNS server. Checked that I can ping the dns server from the new DC by hostname. When I went ahead and did a DCpromo on the DC, and un-cheked the “install DNS” option, everything seemed to go well (no error messages), but I saw no changes on the DNS server whatsoever (no additional settings). Plus, the DNS server seems to be unable to join the domain, as it claims that the domain is not discoverable. As a final note, I do run Symantec Endpoint Protection, which includes a firewall and most settings set as default. I have not yet tried turning this off, but my experience has been that if a service would open up a port on a Windows firewall, it would do the same through Symantec. There is pretty tight integration these days with corporate-class AV and Windows. I have a template vhdx fully set up (just short of any special roles and features) that I can use to replace the current AD VM with, so doing this all over again is not too much skin off of my nose.

  Read the article

• installing mac os on intel [closed]

  - by bassha

  Possible Duplicate: Installing Mac OS X on Non Apple Hardware hello i have an intel based computer, it's hp pavillion dv6000, it's cpu is 1.6ghz duocore and has 1GB of ram. i installed the mac os x leopard for intel on it, on a 12GB partition, but it's not working. i can boot to the mac and the os display a picture and a welcoming song then it stop doing anything. does the mac os x need a special intel requirements?

  Read the article

• Can Mac KeyNote presentations exported for Windows be shown in good quality and be edited?

  - by Edward Tanguay

  A friend asked me this: ...I stopped using KeyNote for one simple reason – contrary to the Mac marketing blurb, the final presentations do NOT work fine on Windows PCs – they look distorted and have formatting quirks which cannot be corrected because the Windows/Powerpoint file it has supposedly been saved as is in fact a non-editable file, kind of like a pdf. Is there a way to create Mac KeyNote presentation files so they look nice on Windows and can be edited?

  Read the article

• Best practice for setting up SQL server on a Virtual Machine

  - by CrazyCoderz

  This is my first attempt at virtualizing SQL server on VMWare and I want to make sure I am doing things correctly. Should I have SQL server installed on the C: drive / same partition as the OS, Then add a virtual disk for the Data files, say 300GB, and then another virtual disk for the log files say 100GB? Or should I add 2 300GB vdisks, for the data files mirror them in the operating system, and then add a non mirrored vdisk of 100GB for LogFiles??

  Read the article

• VPS with Plesk, one ip, and godaddy (definely need help)

  - by Francesco

  Hi there, here's my situation : i've Plesk 8.3.0 with one IP and i've registered my domains at godaddy.com My problem : i cannot figure out how to configure plesk and godaddy to have my domains (6) properly working into the VPS. i've only one IP, so i can't have my personal NS and need to use godaddy ns. But.. how do i set all the stuff ? I've made a try but it's not working. Please take a look : This is an example of how the domain i'm actually working on is configured On Plesk : Host Record type Value 1.2.3.4 / 24 PTR mydomain.com. ftp.mydomain.com. CNAME mydomain.com. mail.mydomain.com. A 1.2.3.4 ns.mydomain.com. A 1.2.3.4 mydomain.com. NS ns.mydomain.com. mydomain.com. A 1.2.3.4 mydomain.com. MX (10) mail.mydomain.com. webmail.mydomain.com. A 1.2.3.4 www.mydomain.com. CNAME mydomain.com. On godaddy,(Total DNS Control) for the same domain i have this setup : A (Host) Host Points To TTL Actions * 1.2.3.4 1 Hour CNAMES (Aliases) Host Points To TTL Actions e email.secureserver.net 1 Hour email email.secureserver.net 1 Hour ftp @ 1 Hour imap imap.secureserver.net 1 Hour mail pop.secureserver.net 1 Hour mobilemail mobilemail-v01.prod.mesa1.secureserver.net 1 Hour pda mobilemail-v01.prod.mesa1.secureserver.net 1 Hour pop pop.secureserver.net 1 Hour smtp smtp.secureserver.net 1 Hour webmail webmail.secureserver.net 1 Hour www @ 1 Hour MX (Mail Exchange) Priority Host Goes To TTL Actions 10 @ mailstore1.secureserver.net 1 Hour 0 @ smtp.secureserver.net Host Points To TTL Actions @ ns53.domaincontrol.com @ ns54.domaincontrol.com What should i correct ? Thanks for helping me Francesco

  Read the article

• Can I import another users calendar into Outlook 2010 and maintain his color highlights?

  - by Matthias Mayer

  I am importing a colleagues complete Outlook 2010 calendar (sent by mail as .ics file). However, all coloring is lost: categories, automatically formatted entries, etc. are not visualized in my colleagues colors - just in a non-distinguishable standard office style. Is there a way that my colleague also sends me his color preferences, ie. to maintain his individual coloring in my view? Thanks in advance! Matthias

  Read the article

• Tomcat IIS 7 Integration gives 503 errors on all requests.

  - by Yvan JANSSENS

  Hi, After many attempts to install Tomcat on IIS 7, I finally managed to get it working. At least I think so :-S. I finally got the 500 errors away, by setting the correct permissions. The only thing that doesn't work is ... serving stuff: neither regular stuff (like ASP, HTML files, or directory browsing) or Tomcat things work. Here are my configs: Worker.properties # The workers that your plugins should create and work with # worker.list=worker1 #------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # Defining a worker named ajp13 and of type ajp13 # Note that the name and the type do not have to match. # worker.worker1.port=8009 worker.worker1.host=127.0.0.1 worker.worker1.type=ajp13 URIWorkerMap.properties /|/*=worker1 # Exclude the subdirectory static: !/static|/*=worker1 # Exclude some suffixes: !*.html=worker1 !*.asp=worker1 Server.xml <?xml version='1.0' encoding='utf-8'?> <!-- Licensed to the Apache Software Foundation (ASF) under one or more contributor license agreements. See the NOTICE file distributed with this work for additional information regarding copyright ownership. The ASF licenses this file to You under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. --> <!-- Note: A "Server" is not itself a "Container", so you may not define subcomponents such as "Valves" at this level. Documentation at /docs/config/server.html --> <Server port="8005" shutdown="SHUTDOWN"> <!--APR library loader. Documentation at /docs/apr.html --> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <!--Initialize Jasper prior to webapps are loaded. Documentation at /docs/jasper-howto.html --> <Listener className="org.apache.catalina.core.JasperListener" /> <!-- Prevent memory leaks due to use of particular java/javax APIs--> <Listener className="org.apache.catalina.core.JreMemoryLeakPreventionListener" /> <!-- JMX Support for the Tomcat server. Documentation at /docs/non-existent.html --> <Listener className="org.apache.catalina.mbeans.ServerLifecycleListener" /> <Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener" /> <!-- Global JNDI resources Documentation at /docs/jndi-resources-howto.html --> <GlobalNamingResources> <!-- Editable user database that can also be used by UserDatabaseRealm to authenticate users --> <Resource name="UserDatabase" auth="Container" type="org.apache.catalina.UserDatabase" description="User database that can be updated and saved" factory="org.apache.catalina.users.MemoryUserDatabaseFactory" pathname="conf/tomcat-users.xml" /> </GlobalNamingResources> <!-- A "Service" is a collection of one or more "Connectors" that share a single "Container" Note: A "Service" is not itself a "Container", so you may not define subcomponents such as "Valves" at this level. Documentation at /docs/config/service.html --> <Service name="Catalina"> <!--The connectors can use a shared executor, you can define one or more named thread pools--> <!-- <Executor name="tomcatThreadPool" namePrefix="catalina-exec-" maxThreads="150" minSpareThreads="4"/> --> <!-- A "Connector" represents an endpoint by which requests are received and responses are returned. Documentation at : Java HTTP Connector: /docs/config/http.html (blocking & non-blocking) Java AJP Connector: /docs/config/ajp.html APR (HTTP/AJP) Connector: /docs/apr.html Define a non-SSL HTTP/1.1 Connector on port 8080 --> <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> <!-- A "Connector" using the shared thread pool--> <!-- <Connector executor="tomcatThreadPool" port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> --> <!-- Define a SSL HTTP/1.1 Connector on port 8443 This connector uses the JSSE configuration, when using APR, the connector should be using the OpenSSL style configuration described in the APR documentation --> <!-- <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" /> --> <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" /> <!-- An Engine represents the entry point (within Catalina) that processes every request. The Engine implementation for Tomcat stand alone analyzes the HTTP headers included with the request, and passes them on to the appropriate Host (virtual host). Documentation at /docs/config/engine.html --> <!-- You should set jvmRoute to support load-balancing via AJP ie : <Engine name="Catalina" defaultHost="localhost" jvmRoute="jvm1"> --> <Engine name="Catalina" defaultHost="localhost"> <!--For clustering, please take a look at documentation at: /docs/cluster-howto.html (simple how to) /docs/config/cluster.html (reference documentation) --> <!-- <Cluster className="org.apache.catalina.ha.tcp.SimpleTcpCluster"/> --> <!-- The request dumper valve dumps useful debugging information about the request and response data received and sent by Tomcat. Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.valves.RequestDumperValve"/> --> <!-- This Realm uses the UserDatabase configured in the global JNDI resources under the key "UserDatabase". Any edits that are performed against this UserDatabase are immediately available for use by the Realm. --> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/> <!-- Define the default virtual host Note: XML Schema validation will not work with Xerces 2.2. --> <Host name="localhost" appBase="webapps" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> <!-- SingleSignOn valve, share authentication between web applications Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Access log processes all example. Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.valves.AccessLogValve" directory="logs" prefix="localhost_access_log." suffix=".txt" pattern="common" resolveHosts="false"/> --> </Host> </Engine> </Service> </Server> http://localhost:8080 is working, I can view the apps and configure them there... I'm quite new to IIS 7, I used to work with IIS 6. Thanks in advance, Yvan

  Read the article

• Testing HTTP status codes

  - by amusero

  I'm running an Apache Tomcat server. Making some security testing I'd noticed than my server is returning a 200 HTTP status code of the default error page when I try to access to a non-existent element instead of return a 404 status code and redirect me to the default error page. I suspect that this is not the only fail with this issue. Anyone can suggest me a process to chech the most common HTTP status codes?

  Read the article

• bash watch command with colors preserved

  - by Pawel Goscicki

  From man watch: Non-printing characters are stripped from program output. Use "cat -v" as part of the command pipeline if you want to see them. So how do I use cat -v if I want to see the colored output from: watch ls -al --color

  Read the article

• What are the good alternatives to Windows Movie Maker in Vista?

  - by GeneQ

  Short of getting a Mac and using iMovie, what are the alternatives that you'll recommend to a non-profit organization that needs to produce simple (but polished) videos to showcase their community service activities to raise funds. Currently they are using Windows Movie Maker but have sort of outgrown it. I installed Jashaka for them, and understandably, they couldn't grok it at all. Their current system is powerful enough to handle most video editing tasks.

  Read the article

• watch with bash colors preserved

  - by Pawel Goscicki

  From man watch: Non-printing characters are stripped from program output. Use "cat -v" as part of the command pipeline if you want to see them. So how do I use cat -v if I want to see the colored output from: watch ls -al --color

  Read the article

• How can i change the SSH port used on Plesk 9 for Migration Manager?

  - by Matthew Lanham

  Hey All, My hosting company have a non standard SSH port configured on my current server, i am now looking to migrate to a new server and want to use the Plesk Migration Manager, however it seems that you cannot specify the port in the host name like 127.0.0.1:xxx Any ideas? and thanks!

  Read the article

• ubuntu 10.04 logs itself out overnight

  - by Corey

  Every night when I leave work, I lock the screen via ubuntu's "power" button in the top right hand panel. When I come to work in the morning, I'm greeted with the log-in screen. This doesn't happen every night, but most. I'm running ubuntu 10.04 on a Dell inspiron. I've included some HW specs, and also dmesg output. Please let me know what other logs may be useful. thanks! Corey ~$ dmesg [20559.696062] type=1503 audit(1285957687.048:16): operation="open" pid=6212 parent=1 profile="/usr/bin/evince" requested_mask="::r" denied_mask="::r" fsuid=1000 ouid=0 name="/usr/local/lib/libltdl.so.7.2.2" [21127.951621] type=1503 audit(1285958255.300:17): operation="open" pid=6390 parent=1 profile="/usr/bin/evince" requested_mask="::r" denied_mask="::r" fsuid=1000 ouid=0 name="/usr/local/lib/libltdl.so.7.2.2" [291038.528014] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [291038.528025] render error detected, EIR: 0x00000000 [291038.528042] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 22973891 at 22973890) [291038.828014] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [291038.828023] render error detected, EIR: 0x00000000 [291038.828042] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 22973894 at 22973890) ~$ lspci -vv 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 27 Region 0: Memory at fe400000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at dc00 [size=8] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at feaf8000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: 80000000-801fffff Prefetchable memory behind bridge: 0000000080200000-00000000803fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: feb00000-febfffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at d880 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at d800 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at d480 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d400 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) (prog-if 20) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at feaf7c00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt, intel-rng 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at d080 [size=8] Region 1: I/O ports at d000 [size=4] Region 2: I/O ports at cc00 [size=8] Region 3: I/O ports at c880 [size=4] Region 4: I/O ports at c800 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 4: I/O ports at 0400 [size=32] Kernel modules: i2c-i801 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: I/O ports at e800 [size=256] Region 2: Memory at fdfff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fdfe0000 (64-bit, prefetchable) [size=64K] Expansion ROM at febe0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 log$ tail -n 15 Xorg.0.log.old for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information. (II) Power Button: Close (II) UnloadModule: "evdev" (II) Power Button: Close (II) UnloadModule: "evdev" (II) USB Optical Mouse: Close (II) UnloadModule: "evdev" (II) Dell Dell USB Entry Keyboard: Close (II) UnloadModule: "evdev" (II) Macintosh mouse button emulation: Close (II) UnloadModule: "evdev" (II) AIGLX: Suspending AIGLX clients for VT switch ddxSigGiveUp: Closing log

  Read the article

• Tablet with Dedicated Graphics

  - by GuyNoir

  What would be the best tablet PC with dedicated graphics. I can find a few, but most seem to be from around 2006-07. Is there anything newer that has both the tablet-based swivel screen and a non-integrated graphics board? Thanks.

  Read the article

• Dynamic ARP Entries turning into Static ARP entries

  - by Zach

  I recently acquired a client that has a strange ARP caching issue on one of thier servers. I have a server that will eventually start turning it's dynamic ARP entries into static ARP entries. This causes problems because when the machine that has a static ARP entries on this server receives a new IP via DHCP, then the server is not able to communicate with the clients. Clearing the ARP cache resolves the issue and the server is fine for about a week and then it starts slowly turning ARP entries into static ARP entries. I haven't narrowed it down to when or how many it starts to do, but slowly you start seeing 1 static ARP and then 5 and then 10. The server in question is a Windows Server 2003 SP2. It is a DC, DHCP, and DNS server. I've checked the DHCP scope options and there's nothing in there that would indicate anything to do with static ARP entries. The only thing different between this DNS server and our other DNS server is that the 'Dynamically Update DNA A and PTR records for DHCP clients that do not request updates' is checked on the problematic server. I've done a bit of research about this and it seems that this may happen if any PXE type services are running, from what I can tell, there is nothing running a PXE server. I'm a bit lost as I have never seen dynamic ARP entries start to turn into static ARP entries. Right now my solution is a schedule task that runs every 24 hours to clear the ARP cache (arp -d *). I would like to not rely on this schedule task. Has anybody seen this before or have any suggestions on how to troubleshoot this?

  Read the article

• Windows remote administration suite that doesn't rely on Active Directory, Domains, etc

  - by glasnt

  I know there are a number of suites out there that allow Windows machines on a Domain, or in Active Directory to be remotely administrated (windows updates, program installs, maintenance, etc); but does there exist a package that does this for non-AD/Domain setups? The kind of things I'm looking for: manage windows updates, + automatic applying custom package pushing (custom scripts, etc) general maintenance, visibily of health works for 2003/2008/2008R2 works without Active Directory or being part of a Domain (Might be able to manage putting all the machines on a Workgroup, if that helps)

  Read the article

• Volume keys not working after installing Silverlight

  - by terry

  I downloaded Silverlight for Safari to use Netflix. This download has caused my MacBook's volume keys to become non-functional, although I can still change volume through the icon in the menu bar or through system preferences. When I press the keys to change the volume, the transparent volume icon appears on the screen with a circle-slash icon at bottom center. Does anyone know how to make the keys functional again? I deleted Silverlight but still no sound.

  Read the article

• Virus protection for flash drives.

  - by The Green Frog

  At school, there is a large network with lots of non-technical minded people and lots of viruses. How can I protect my flash drive from these worms and viruses so I don't bring them home and infect my home computers?

  Read the article

• Unable to ping domain.local, but can ping server.domain.local

  - by Force Flow

  I have a single windows 2008 server running active directory, group policy, and DNS. DHCP is running from the firewall (this is because there are multiple branch locations, and each location has its own firewall supplying DHCP. But, for this problem, the server and workstation are at the same location). On an XP workstation, if I try to visit \\domain.local or ping domain.local, the workstation can't find it. A ping returns Ping request could not find host domain.local. If I try to visit \\server or \\server.domain.local or ping server or server.domain.local, I'm able to connect normally. If I ping or visit domain.local on the server, I'm able to connect normally. A-Records are in place in the DNS service for server, domain.local, and server.domain.local. A reverse lookup zone also is enabled and PTR records are in place. If I wait 20-30 minutes, I am eventually able to ping and visit domain.local--but, when attempting to ping, it takes 30 second to return an IP address. I am also unable to join a new workstation to the domain during this wait period. If I try, the error message returned is "network path not found". Is there something I'm missing?

  Read the article

• Linux-Mint Maya Mate loses Alt-F1 menu and Alt-F2 run-dialog with Compiz

  - by Peter.O

  I like the Linux-Mint 13 Mate Alt-F1 menu and the Alt-F2 run-dialog, but as soon as I installed Compiz those keys became non-functional. Conpiz has a Gnome compaatibility settings panel which allows you to set these keys, but using that Compix settings panel did not make any diference (probably because Mate is not Gnome, strictly speaking)... Is there some way to get those two shortcut keys back into acton with Compiz?

  Read the article

• Is it reasonable that a random disk seek & read costs ~16ms?

  - by fzhang

  I am frustrated about the latency of random reading from a non-ssd disk. Based on results from following test program, it speeds ~16 ms for a random read of just 512 bytes without help of os cache. I tried changing 512 to larger values, such as 25k, and the latency did not increase as much. I guess it is because the disk seek dominates the time. I understand that random reading is inherently slow, but just want to be sure that ~16ms is reasonable, even for non-ssd disk. #include <sys/stat.h> #include <sys/time.h> #include <sys/types.h> #include <sys/unistd.h> #include <fcntl.h> #include <limits.h> #include <stdio.h> #include <string.h> int main(int argc, char** argv) { int fd = open(argv[1], O_RDONLY); if (fd < 0) { fprintf(stderr, "Failed open %s\n", argv[1]); return -1; } const size_t count = 512; const off_t offset = 25990611 / 2; char buffer[count] = { '\0' }; struct timeval start_time; gettimeofday(&start_time, NULL); off_t ret = lseek(fd, offset, SEEK_SET); if (ret != offset) { perror("lseek error"); close(fd); return -1; } ret = read(fd, buffer, count); if (ret != count) { fprintf(stderr, "Failed reading all: %ld\n", ret); close(fd); return -1; } struct timeval end_time; gettimeofday(&end_time, NULL); printf("tv_sec: %ld, tv_usec: %ld\n", end_time.tv_sec - start_time.tv_sec, end_time.tv_usec - start_time.tv_usec); close(fd); return 0; }

  Read the article

• OS X rpc.statd warning failed to contact host

  - by Obsidian

  When I log into my mac on 10.6.3 I get the following error in my console 29/05/2010 19:11:43 prometheus rpc.statd[109] Warning Failed to contact host aphrodite.lan: RPC: Unknown host Now I know that rpc is trying to contact a non existent host but what I can't figure out is why and how to stop it. Any ideas?

  Read the article

• Web server hits from Akamai IP addresses

  - by Joel

  I am getting a lot of hits to my web server from from multiple IP addresses that are owned by Akamai. This stood out to me as the requests are for resources that are no longer available. These resources should not be being requested - that pages that refer to them are marked as being non-cachable. Any clues?

  Read the article

• dns configuration error in plesk

  - by Karthik Malla

  I purchased a domain www.softmail.me at Godaddy.com and tried it DNS and getting lots of errors and finally change my nameservers to my server DNS i.e. NS101.VPSLAND.COM and NS202.VPSLAND.COM and created a domain in my plesk panel (Marked DNS & Mail required). After adding my domain to my plesk panel of my server I opened DNS records of that domain and found DNS records are automatically generated to my needs as following 65.75.241.26 / 24 PTR softmail.me. ftp.softmail.me. CNAME softmail.me. lists.softmail.me. CNAME softmail.me. mail.softmail.me. A 65.75.241.26 mssql.softmail.me. A 65.75.241.26 ns.softmail.me. A 65.75.241.26 sitebuilder.softmail.me. A 65.75.241.26 softmail.me. NS ns.softmail.me. softmail.me. A 65.75.241.26 softmail.me. MX (10) mail.softmail.me. webmail.softmail.me. A 65.75.241.26 www.softmail.me. CNAME softmail.me. Finally I waited for a week for I am unable to use my domain. Also in DNS lookup I cannot find any records to my Server except name servers of VPSland. Do I need to add VPSland namesevers anywhere in Plesk panel? If so where? Can anyone assist me where the mistake is?...

  Read the article

• How to measure disk-performance under Windows?

  - by Alphager

  I'm trying to find out why my application is very slow on a certain machine (runs fine everywhere else). I think i have traced the performance-problems to hard-disk reads and writes and i think it's simply the very slow disk. What tool could i use to measure hd read and write performance under Windows 2003 in a non-destructive way (the partitions on the drives have to remain intact)?

  Read the article

< Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >