Search Results

Search found 669 results on 27 pages for 'multicast'.

Page 19/27 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >

• On Mikrotik RouterOS, is it possible to get Netflow information from a bridged connection?

  - by Tim

  I have a RouterOS box set up to bridge two ethernet connections. I have use-ip-firewall=yes in the bridge configuration, so that the ports go through the firewall. I've enabled netflow reporting via ip/traffic-flow, but the only packets I see reported are broadcast and multicast packets, not the packets that are flowing through the bridge. The documentation indicates that traffic flow logging happens after firewall processing and that it won't work with bridged connections by default, but I would have thought that use-ip-firewall=yes ought to address this. Is it possible to make this work somehow?

  Read the article

• Problems with wired ethernet connection Ubuntu 11.10

  - by Andrew Fielden

  After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

  Read the article

• Ubuntu connects to wireless but doesn't work!

  - by UbuntuUser990

  I just installed Ubuntu 14.04 LTS on my laptop, it connects to my wireless network and shows that it is connected, but when I try to load a webpage or do anything like download Steam for Dota 2, it doesn't work. When I try to connect my Facebook account to Ubuntu, it doesn't work. I want to be able to use Ubuntu with working internet access. What do I do?. ifconfig this shows up eth0 Link encap:Ethernet HWaddr 88:ae:1d:60:56:eb inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) When I type ping askubuntu.com this shows up ping: unknown host askubuntu.com

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• A Linux DHCP server that will listen on an non-broadcast (tap) interface?

  - by TomOnTime

  Are there any Linux DHCP servers that will listen to what Cisco calls an "unnumbered" interface, or what others might call a "NBMA" (non-broadcast) interface. I have a Linux system that connects to a number of others using GRE tunnels. The machines on the other end send DHCP requests to this machine, I can see them with tcpdump. However, ISC DHCP 3.0.3 refuses to listen to the interface because it is non-broadcast. The interface I'd like DHCP to listen to is: tap2 Link encap:Ethernet HWaddr removed-for-privacy inet6 addr: removed-for-privacy/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:518 errors:0 dropped:0 overruns:0 frame:0 TX packets:510 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:196242 (191.6 KiB) TX bytes:52425 (51.1 KiB)

  Read the article

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Wifi - wireless network not working after installing Ubuntu 12.04

  - by Nilesh

  I had installed ubuntu 12.04 in my Dell Vostro 3460. Initially wired as well wireless both are not working. After installing compat-wireless-2012-07-03-pc.tar.bz2 wired network fine but wireless is not working. Previously both were working fine with ubuntu 11.10. Also presently both network are working fine in Win7. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) iwconfig: lo no wireless extensions. eth0 no wireless extensions. ifconfig: eth0 Link encap:Ethernet HWaddr 84:8f:69:d4:35:9b inet addr:10.24.22.72 Bcast:10.24.31.255 Mask:255.255.224.0 inet6 addr: fe80::868f:69ff:fed4:359b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15332 errors:0 dropped:0 overruns:0 frame:0 TX packets:10425 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:9262594 (9.2 MB) TX bytes:1572030 (1.5 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1432 errors:0 dropped:0 overruns:0 frame:0 TX packets:1432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145656 (145.6 KB) TX bytes:145656 (145.6 KB)

  Read the article

• Dnsmasq offering IP via DHCP, but nobody is accepting

  - by Matt

  As clients connect the logs light up with DHCPDISCOVER(wlan0) and DHCPOFFER(wlan0) but the IPs being offered are not being accepted. Currently dnsmasq offers IPs on eth1 which works flawlessly. It seems to be just wlan0 that poses this problem for me today. ifconfig of wlan0: wlan0 Link encap:Ethernet HWaddr aa:aa:aa:aa:aa:aa inet addr:10.0.0.2 Bcast:10.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::baa3:86ff:fe70:796a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1609 errors:0 dropped:0 overruns:0 frame:0 TX packets:1268 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:308739 (301.5 KiB) TX bytes:319185 (311.7 KiB)

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• Bluetooth not working on Acer 3820tg (Ubuntu 12.04)

  - by Iohannes

  After upgrading to 12.04 (it was done by a complete reinstallation), bluetooth doesn't work anymore. Before (I think it was Ubuntu 11.04), I just followed instructions on this page and copied /lib/firmware/ath3k-2.fw to /lib/firmware/ath3k-1.fw and everything was fine. But in 12.04, there isn't any ath3k-2.fw in the /lib directory, so this method is not possible. Also, pressing Fn+F3 doesn't work. I would appreciate any help. Some further information (I hope it's enough): dmesg [ 23.063710] Bluetooth: Core ver 2.16 [ 23.063740] NET: Registered protocol family 31 [ 23.063743] Bluetooth: HCI device and connection manager initialized [ 23.063746] Bluetooth: HCI socket layer initialized [ 23.063747] Bluetooth: L2CAP socket layer initialized [ 23.063972] Bluetooth: SCO socket layer initialized [ 23.066930] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 23.066934] Bluetooth: BNEP filters: protocol multicast [ 23.068422] Bluetooth: RFCOMM TTY layer initialized [ 23.068428] Bluetooth: RFCOMM socket layer initialized [ 23.068430] Bluetooth: RFCOMM ver 1.11 lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 003: ID 046d:c05f Logitech, Inc. Bus 002 Device 004: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 005: ID 0402:9665 ALi Corp. Gateway Webcam hcitool dev Devices:

  Read the article

• Static IP Address on Ubuntu 12.04 Virtual Machine

  - by chrisnankervis

  I've setup a VM running Ubuntu 12.04 specifically for local web development and am having some problems ensuring it has a static IP address. A static IP address is important as I'm using the IP address in my hosts file to assign a .local suffix to addresses used both in browser and to connect to the correct database on the VM. Currently, every time I connect to a new network or my VM is assigned a new IP address I need to reconfigure my whole environment which is becoming quite a pain. It also probably doesn't help that the default-lease-time on the Ubuntu VM is set to 1800 by default. At the moment I'm using VMWare Fusion and the Network Adapter is enabled and set to "Autodetect" under Bridged Networking. I've tried to set a static IP address within the dhcpd.conf using the code below: host ubuntu { hardware ethernet 00:50:56:35:0f:f1; fixed-address: 192.168.100.100; } The fixed-address that I've used is also outside the range specified in the subnet block (which in this case is 192.168.100.128 to 192.168.100.254). I've tried adding and removing the network adapter and restarting my Mac after each time to no avail. Below is an ifconfig of the VM that might be of some help: eth0 Link encap:Ethernet HWaddr 00:50:56:35:0f:f1 inet addr:192.168.0.25 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe35:ff1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1624 errors:0 dropped:0 overruns:0 frame:0 TX packets:416 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:147348 (147.3 KB) TX bytes:41756 (41.7 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Are there any specific issues with 12.04 that I'm missing? Otherwise has anyone else got any ideas? Thanks in advance.

  Read the article

• Internet slow on one router only [the problem only in Ubuntu] [on hold]

  - by mrSuperEvening

  Internet works perfectly on every other router, but browsing sucks at home (slow browsing and slow loading times). I changed DNS servers to 8.8.0.0, still doesn't help. And funnily, download speed is extremely high on this network (meaning torrents for example), but using browsers and loading websites is extremely slow (only on this network). Do I need to change something in router settings or what can I try? By the way, I use wired connection to router. EDIT: There's no problems when using Windows. EDIT: ifconfig: eth0 Link encap:Ethernet HWaddr f2:4d:a0:c0:3f:4c inet addr:192.168.11.8 Bcast:192.168.11.255 Mask:255.255.255.0 inet6 addr: fe80::f24d:a2ff:fec6:3f4c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:206798 errors:0 dropped:0 overruns:0 frame:0 TX packets:219570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76680734 (76.6 MB) TX bytes:21738160 (21.7 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11094 (11.0 KB) TX bytes:11094 (11.0 KB)` ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (213.159.32.147) 56(84) bytes of data. 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=1 ttl=61 time=0.936 ms 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=2 ttl=61 time=0.937 ms --- google.com ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.936/0.936/0.937/0.030 ms

  Read the article

• There's IP but can't reach gateway

  - by icky

  I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

  Read the article

• how to change interface ip in ifconfig with /etc/network/interfaces

  - by user2478348

  Hi everybody when modifiying /etc/network/interfaces, saving it and then executing ifconfig i can't see the modification i made..for example here is part of my /etc/network/interfaces: auto wlan1 iface wlan1 inet static address 192.168.0.60 netmask 255.255.255.0 gateway 192.168.0.61 you can see that the IP address of my wlan1 is 192.168.0.60 but when typing ifconfig i have this: wlan1 Link encap:Ethernet HWaddr 00:19:70:0f:c2:9c inet adr:192.168.0.1 Bcast:192.168.0.255 Masque:255.255.255.0 adr inet6: fe80::219:70ff:fe0f:c29c/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:758 erreurs:0 :0 overruns:0 frame:0 TX packets:610 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:73490 (73.4 KB) Octets transmis:127883 (127.8 KB) (the inet adr:192.168.0.1 and not 198.168.0.60)..if someone can help me I'll be very thankful :)

  Read the article

• Wired connection problem through router

  - by tommypincha

  I'm having trouble to connect my Ubuntu 11.10 to internet through ethernet. I installed a router to get Wi-Fi and now (by a wired connection) I can't have internet with ubuntu (but I can with Windows 7). I see several attempts per minute of the network-manager to get a connection, but after a minute it stops trying. Here are a couple of outputs from key files: cat /etc/network/interfaces auto lo iface lo inet loopback and ifconfig -a eth0 Link encap:Ethernet HWaddr 00:16:76:e4:a6:e8 inet6 addr: fe80::216:76ff:fee4:a6e8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:117 dropped:0 overruns:0 frame:117 TX packets:50 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:12221 (12.2 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:582 errors:0 dropped:0 overruns:0 frame:0 TX packets:582 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:46024 (46.0 KB) TX bytes:46024 (46.0 KB) I tried reconnecting the modem and the router and reconnecting the ethernet cable but nothing... I tried other solutions from other posts (this one has a similar issue Wired connection not working) but again nothing. My IP is dynamic. A couple of things I see and did: I see no inet addr, only inet6. I ignored ipv6 from the internet connections, and restarted the network-manager service and nothing. A difference with the post I mentioned is the RX packets with errors I have, is this a clue of the problem? Any help would be appreciated, Thanks!

  Read the article

• A "tinkered" PC can ping by IP, not by hostname. How to fix?

  - by aitchnyu

  Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

  Read the article

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• What are the IPv6 Public and Private and Reserved ranges

  - by vipin raj

  I just want to know what are all the public IPv6 ranges which ISPs or other users can use? Also need a list of addresses which can be used in private networks and also the list of addresses which never can be used in any network. I have been searching through different web sites. But none gives a reliable answer. Actually we are developing an application which allows user to plan their IP address(create supernets, subnets, hosts, assign host to ports etc). So my application should be able to distinguish between all kinds of address ranges, whether it is reserved, public, private, multicast etc

  Read the article

• How to add a broadcast address to loopback with ifconfig on a OS/X?

  - by chrisapotek

  I am trying to use ifconfig to turn on broadcast on my loopback interface. It currently reads: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 As you can see, no broadcast address! :( :( :( I tried this on OS/X but it did not work and it did not give any error or feedback: ifconfig lo0 broadcast 127.255.255.255 Any guru would know that? I have one server that sends one packet. I have two clients running on the same machine as the server. I need them to pick up the packet WITHOUT having to force the server to send it twice.

  Read the article

• iPhone VPN to iTunes Home Sharing

  - by Philip Crumpton

  my goal is to set up a VPN on a Windows machine that contains my iTunes library then connect to that VPN with my iPhone and be able to utilize Home Sharing remotely. I have read that this can easily be set up if the iTunes library is on a Mac (Network Beacon and YazSoft ShareTool are two products I quickly found). I can't find anyone who has had success on a Windows machine, though. In my thinking, there are two options (aside from buying a Mac): 1.) Existing utility that takes care of this for me (like the Mac-only options listed above) and is compatible with iPhone (Hamachi is NOT compatible with iPhone VPN) 2.) Manually configure a VPN to allow Bonjour multicast (can't find any information on this) FYI my router is a Linksys WRT54GL running Tomato 1.28

  Read the article

• Wired Connection Problem

  - by Dave

  After upgrading to 12.04 my interent connection no longer works. More precisely it is really, really, slow, and occasionally will connect, but do so only for a few moments and then disappear again. I am on a Lenovo Workstation e20. Output of ifconfig: eth0 Link encap:Ethernet HWaddr 70:f3:95:00:64:3e inet addr:192.168.1.20 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::72f3:95ff:fe00:643e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7398 errors:0 dropped:74 overruns:0 frame:0 TX packets:6684 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5407828 (5.4 MB) TX bytes:854343 (854.3 KB) Interrupt:20 Memory:fb120000-fb140000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1587 errors:0 dropped:0 overruns:0 frame:0 TX packets:1587 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:152089 (152.0 KB) TX bytes:152089 (152.0 KB) I am really at a loss for what to do. I am relatively new to Ubuntu, searched the other user questions and couldn't figure this out.

  Read the article

• Wireless drivers

  - by Kencer

  The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

  - by user42424

  So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

  Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >