Search Results

Search found 1227 results on 50 pages for 'richard ev'.

Page 19/50 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >

• Any problems usinga GoDaddy SSL certificate on a Cisco ASA firewall?

  - by Richard West

  I need to purchase and install a SSL certificate on my Cisco ASA firewall. This will allow my VPN users to connect to my ASA without receiving the certificate error from the untrusted self assigned SSL certificate that is currently on the ASA. I had good experiences with the SSL certificates that GoDaddy sells. However, I'm concerned about using them. On my web servers I have to also install GoDaddy's "intermediate certificate bundle". On the ASA I do not think that I will be able to preform anything like this. I do not fully understand what the "intermediate certificate bundle" does, but obviously it's important. So my question is can I use a GoDaddy SSL certificate on an ASA without my users getting any type of warning or error about connecting to a site that using an untrusted SSL certificate. I need this to be as simple as possible for my end users and warning messages are always scary :) Thanks!

  Read the article

• How to install PHP5.3 and SQLite3 on Ubuntu 8.04

  - by richard

  Hello, I got a Ubuntu Hardy VPS and I am trying to install PHP5.3 with SQLite. I added the dotdeb PHP5.3 repository and succeeded in installing PHP5.3. But I need to install SQLite as well. When I'm trying to install php5-sqlite3 (sudo aptitude install php5-sqlite3) this is the output: The following packages are BROKEN: php5-sqlite3 The following NEW packages will be automatically installed: php-db php-pear php-sqlite3 The following NEW packages will be installed: php-db php-pear php-sqlite3 0 packages upgraded, 4 newly installed, 0 to remove and 0 not upgraded. Need to get 460kB of archives. After unpacking 3027kB will be used. The following packages have unmet dependencies: php5-sqlite3: Depends: phpapi-20060613 which is a virtual package. Resolving dependencies... The following actions will resolve these dependencies: Remove the following packages: libapache2-mod-php5 php5 php5-mysql Install the following packages: php-pear [5.2.4-2ubuntu5.10 (hardy-updates, hardy-security)] Downgrade the following packages: php5-cli [5.3.1-0.dotdeb.1 (<NULL>, now) -> 5.2.4-2ubuntu5.10 (hardy-updates, hardy-security)] php5-common [5.3.1-0.dotdeb.1 (<NULL>, now) -> 5.2.4-2ubuntu5.10 (hardy-updates, hardy-security)] php5-suhosin [5.3.1-0.dotdeb.1 (<NULL>, now) -> 0.9.22-1 (hardy)] Score is 197 Accept this solution? [Y/n/q/?] Obviously, downgrading PHP is not an option. Please help me! If upgrading the server to a newer release of Ubuntu makes things easier, that's not a problem.

  Read the article

• FreeBSD 8.1 64bit logrotate - ELF interpreter /libexec/ld-elf-so.1 not found

  - by Richard Knop

  I am trying to get logrotate running on a FreeBSD 8.1 virtual machine. I installed the logrotate with pkg_add, I have created the logrotate.config file and also run: mkdir /var/lib/ touch /var/lib/logrotate.status Now when I do: /usr/local/sbin/logrotate -d /usr/local/etc/logrotate.conf I get this error: ELF interpreter /libexec/ld-elf-so.1 not found Abort The file ld-elf-so.1 exists: locate ld-elf.so.1 /libexec/ld-elf.so.1 /usr/libexec/ld-elf.so.1 /usr/share/man/man1/ld-elf.so.1.1.gz

  Read the article

• Server 2008 R2 Dns Lockup

  - by Richard Maynard

  Hi, We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed Thanks in advance. Regards,

  Read the article

• How do you create a mailing list with Lotus Notes?

  - by Richard Cotton

  I have a list of users of an application stored in an SQL database. I'd like to be able to email these people with useful information. Two parts to the question. How do I send queries to an SQL database from Lotus Notes (v6.5.5), in order to retrieve the email addresses? (I'm okay with what the contents of the query should be, I just need to know how to get Notes talking to the database.) How do I programmatically store these addresses as a group contact?

  Read the article

• links for 2010-12-20

  - by Bob Rhubart

  Oracle BI Applications - Security "I recently had to dig into the standard Oracle BI Applications Security Oracle delivers out of the box. The clients had two security requirements..." - Daan Bakboord (tags: oracle security businessintelligence) Changing DataSource Details Using WLST (Multiple Domains) Jay Sensharma shares a script that will make it "easy for WebLogic Administrator to change all the DataSource UserName and Passwords." (tags: weblogic oracle wlst) Richard Veryard on Architecture: Complexity and Power 2 "Power and complexity are higher-order examples of so-called non-functional requirements. Architects need to be able to reason about the composition and decomposition of non-functional requirements." - Richard Veryard (tags: entarch complexity enterprisearchitecture) Anti-Search patterns - SQL to look for what is NOT there - Part One Oracle ACE Director Lucas Jellema discusses a number of situations in which "you are looking for records that do not exist" and demonstrates several "anti-queries." (tags: oracle otn oracleace sql) SOA & Middleware: Canceling a running composite in SOA Suite 11g Niall Commiskey offers a simple scenario. (tags: oracle soa) SOA Design Patterns in the Cloud | SOA World Magazine Srinivasan Sundara Raja attempts to clear up the "confusion in the air about the applicability of SOA in a Cloud managed environment and whether Cloud is the next generation of SOA." (tags: oracle soa cloud) Mark Nelson: Using WebLogic as a Load Balancer "There are a number of good options available to set up a software load balancer in the test environment," says Mark Nelson. "In this post, we will explore one such option – using the HTTP Cluster Servlet that is included with WebLogic Server." (tags: weblogic oracle otn)

  Read the article

• ubuntu bind9 AppArmor read permission denied (chroot jail)

  - by Richard Whitman

  I am trying to run bind9 with chroot jail. I followed the steps mentioned at : http://www.howtoforge.com/debian_bind9_master_slave_system I am getting the following errors in my syslog: Jul 27 16:53:49 conf002 named[3988]: starting BIND 9.7.3 -u bind -t /var/lib/named Jul 27 16:53:49 conf002 named[3988]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' Jul 27 16:53:49 conf002 named[3988]: adjusted limit on open files from 4096 to 1048576 Jul 27 16:53:49 conf002 named[3988]: found 4 CPUs, using 4 worker threads Jul 27 16:53:49 conf002 named[3988]: using up to 4096 sockets Jul 27 16:53:49 conf002 named[3988]: loading configuration from '/etc/bind/named.conf' Jul 27 16:53:49 conf002 named[3988]: none:0: open: /etc/bind/named.conf: permission denied Jul 27 16:53:49 conf002 named[3988]: loading configuration: permission denied Jul 27 16:53:49 conf002 named[3988]: exiting (due to fatal error) Jul 27 16:53:49 conf002 kernel: [74323.514875] type=1400 audit(1343433229.352:108): apparmor="DENIED" operation="open" parent=3987 profile="/usr/sbin/named" name="/var/lib/named/etc/bind/named.conf" pid=3992 comm="named" requested_mask="r" denied_mask="r" fsuid=103 ouid=103 Looks like the process can not read the file /var/lib/named/etc/bind/named.conf. I have made sure that the owner of this file is user bind, and it has the read/write access to it: root@test:/var/lib/named/etc/bind# ls -atl total 64 drwxr-xr-x 3 bind bind 4096 2012-07-27 16:35 .. drwxrwsrwx 2 bind bind 4096 2012-07-27 15:26 zones drwxr-sr-x 3 bind bind 4096 2012-07-26 21:36 . -rw-r--r-- 1 bind bind 666 2012-07-26 21:33 named.conf.options -rw-r--r-- 1 bind bind 514 2012-07-26 21:18 named.conf.local -rw-r----- 1 bind bind 77 2012-07-25 00:25 rndc.key -rw-r--r-- 1 bind bind 2544 2011-07-14 06:31 bind.keys -rw-r--r-- 1 bind bind 237 2011-07-14 06:31 db.0 -rw-r--r-- 1 bind bind 271 2011-07-14 06:31 db.127 -rw-r--r-- 1 bind bind 237 2011-07-14 06:31 db.255 -rw-r--r-- 1 bind bind 353 2011-07-14 06:31 db.empty -rw-r--r-- 1 bind bind 270 2011-07-14 06:31 db.local -rw-r--r-- 1 bind bind 2994 2011-07-14 06:31 db.root -rw-r--r-- 1 bind bind 463 2011-07-14 06:31 named.conf -rw-r--r-- 1 bind bind 490 2011-07-14 06:31 named.conf.default-zones -rw-r--r-- 1 bind bind 1317 2011-07-14 06:31 zones.rfc1918 What could be wrong here?

  Read the article

• Simple bash scripting

  - by Richard Cotton

  I'm trying to get to grips with bash scripting via cygwin. My script is about as simple as it gets. I change the directory to the root of my C drive, and print the new location. #!/usr/bin/bash cd /cygdrive/c pwd is saved in the file chdir.sh in my home directory. I then call ./chdir.sh from the bash prompt. This results in the error : No such file or directorygdrive/c /cygdrive/c/Documents and Settings/rcotton I definitely have a C drive, and the command cd /cygdrive/c works when I call it directly from the bash prompt. I realise that this problem is likely stupidly simple; please can you tell me what I'm doing wrong.

  Read the article

• WSUS appears to be functioning, however errors are reported in Application Log (DSS Authentication W

  - by Richard Slater

  I re-installed WSUS a few months ago on a new server as part of a server hardware refresh. It is functioning normally downloading, authorizing and supplying patches to workstations. System Specification: HP DL360 G5 Quad 2.5 Zeon 6GB RAM Not Virtualized WSUS 3.2.7600.3226 SQL 2005 Express Windows 2003 R2 SP2 WSS SSL Enabled Every six hours five events are logged to the Application Event Log: Source | Category | ID | Description -------------------------------------------------------------------------------------- Windows Server Update Services | Web Services | 12052 | The DSS Authentication Web Service is not working. Windows Server Update Services | Web Services | 12042 | The SimpleAuth Web Service is not working Windows Server Update Services | Web Services | 12022 | The Client Web Service is not working Windows Server Update Services | Web Services | 12032 | The Server Synchronization Web Service is not working Windows Server Update Services | Web Services | 12012 | The API Remoting Web Service is not working In addition the following .NET Stack Trace is logged in C:\Program Files\Update Services\LogFiles\SoftwareDistribution.log each stack trace is identical except for the names of the services: 2009-11-27 11:56:52.757 UTC Error WsusService.10 HmtWebServices.CheckApiRemotingWebService ApiRemoting WebService WebException:System.Net.WebException: The request failed with HTTP status 403: Forbidden. at System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) at Microsoft.UpdateServices.Internal.ApiRemoting.Ping(Int32 pingLevel) at Microsoft.UpdateServices.Internal.HealthMonitoring.HmtWebServices.CheckApiRemotingWebService(EventLoggingType type, HealthEventLogger logger) at Microsoft.UpdateServices.Internal.HealthMonitoring.HmtWebServices.CheckApiRemotingWebService(EventLoggingType type, HealthEventLogger logger) at Microsoft.UpdateServices.Internal.HealthMonitoring.HealthMonitoringTasks.ExecuteSubtask(HealthMonitoringSubtask subtask, EventLoggingType type, HealthEventLogger logger) at Microsoft.UpdateServices.Internal.HealthMonitoring.HmtWebServices.Execute(EventLoggingType type) at Microsoft.UpdateServices.Internal.HealthMonitoring.HealthMonitoringTasks.Execute(EventLoggingType type) at Microsoft.UpdateServices.Internal.HealthMonitoring.HealthMonitoringThreadManager.Execute(Boolean waitIfNecessary, EventLoggingType loggingType) at Microsoft.UpdateServices.Internal.HealthMonitoring.RemotingChannel.PrivateLogEvents() at System.Runtime.Remoting.Messaging.StackBuilderSink._PrivateProcessMessage(IntPtr md, Object[] args, Object server, Int32 methodPtr, Boolean fExecuteInContext, Object[]& outArgs) at System.Runtime.Remoting.Messaging.StackBuilderSink.SyncProcessMessage(IMessage msg, Int32 methodPtr, Boolean fExecuteInContext) at System.Runtime.Remoting.Messaging.ServerObjectTerminatorSink.SyncProcessMessage(IMessage reqMsg) at System.Runtime.Remoting.Lifetime.LeaseSink.SyncProcessMessage(IMessage msg) at System.Runtime.Remoting.Messaging.ServerContextTerminatorSink.SyncProcessMessage(IMessage reqMsg) at System.Runtime.Remoting.Channels.CrossContextChannel.SyncProcessMessageCallback(Object[] args) at System.Runtime.Remoting.Channels.ChannelServices.DispatchMessage(IServerChannelSinkStack sinkStack, IMessage msg, IMessage& replyMsg) at System.Runtime.Remoting.Channels.SoapServerFormatterSink.ProcessMessage(IServerChannelSinkStack sinkStack, IMessage requestMsg, ITransportHeaders requestHeaders, Stream requestStream, IMessage& responseMsg, ITransportHeaders& responseHeaders, Stream& responseStream) at System.Runtime.Remoting.Channels.BinaryServerFormatterSink.ProcessMessage(IServerChannelSinkStack sinkStack, IMessage requestMsg, ITransportHeaders requestHeaders, Stream requestStream, IMessage& responseMsg, ITransportHeaders& responseHeaders, Stream& responseStream) at System.Runtime.Remoting.Channels.Ipc.IpcServerTransportSink.ServiceRequest(Object state) at System.Runtime.Remoting.Channels.SocketHandler.ProcessRequestNow() at System.Runtime.Remoting.Channels.SocketHandler.BeginReadMessageCallback(IAsyncResult ar) at System.Runtime.Remoting.Channels.Ipc.IpcPort.AsyncFSCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* pOverlapped) at System.Threading._IOCompletionCallback.PerformIOCompletionCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* pOVERLAP) So far I have tried the following: Ensuring the settings were accurate as per TechNet. Checked that there was a suitable binding to 127.0.0.1 binding in IIS. Gone through and checked the settings in IIS as per TechNet. I have discovered that you can run the command wsusutil checkhealth to force the healt check to run, wsusutil can be found in C:\Program Files\Update Services\Tools. When this executese it will tell you to check the application log.

  Read the article

• How to delete this file: Thumbs.db:encryptable

  - by Richard Lopes

  Thumbs.db:encryptable I found this file on my image folder, and i can't delete this. I've tryed reboot my pc, but doesn't works... please help me! Delete Thumbs.db:encryptable Edit1: When i try to delete a folder that contains this file, this message appears: del Thumbs.db* /s /f D: \ My Documents \ My Pictures \ My Photos Christmas \ Thumbs.db: encryptable The system can not find the file specified.

  Read the article

• File transfer problems through VPN when Cisco IPS is enabled

  - by Richard West

  We have a Cisco ASA 5510 firewall with the IPS module installed. We have a customer that we must connect to via VPN to their network to exchange files via FTP. We use the Cisco VPN client (version 5.0.01.0600) on our local workstations, which are behind the firewall and subject to the IPS. The VPN client is successful in connecting to the remote site. However when we start the FTP file transfer we are able to upload only 150K to 200K of data, then everything stops. A minute later the VPN session is dropped. I think I have isolated this to an IPS issue by temporarily disabling the Service Policy on the ASA for the IPS with the following command: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 inactive After this command was issued I then established the VPN to the remote site and was successful in transferring the entire file. While still connected to the VPN and FTP session I issued the command to enable the IPS: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 The file transfer was tried again and was once again successful so I closed the FTP session and reopened it, while keeping the same VPN session open. This file transfer was also successful. This told me that nothing with the FTP programs was being filtered or causing the problem. Furthermore, we use FTP to exchange files with many sites everyday without issue. I then disconnected the original VPN session, which was established when the access-list was inactive, and reconnected the VPN session, now with the access-list active. After starting the FTP transfer the file stopped after 150K. To me this seems like the IPS is blocking, or somehow interfering with the initial VPN setup to the remote site. This only started happening last week after the latest IPS signature updates were applied (sig version 407.0). Our previous sig version was 95 days old becuase the system was not auto updating itself. Any ideas on what could be causing this problem?

  Read the article

• Using the Juniper EX3300 Switch as a router?

  - by Richard Whitman

  I have a Juniper EX3300 switch in a data center. And I have connected one of the uplink ports (ge-0/1/0) to my ISP's router. I want to configure it so that all the devices connected to ports in the same VLAN as ge-0/1/0 can access the Internet. I have done some research, and I haven't gotten anywhere really. I have configured the interface as follows: ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family inet { address xx.xx.xx.xx/32; } } } where xx.xx.xx.xx is the "Customer Router Port IP" assigned by my ISP. When I try to commit, I get the following error: Interface ge-0/1/0.0 not enabled for switching Can some one tell me what is the right way to configure it?

  Read the article

• Installing GeoIP on Mac?

  - by Richard

  I want to install the MaxMind GeoIP C library, so that I can use GeoIP as part of Django. I'm working on MacOS. I've downloaded GeoIP-1.4.8.tar.gz from here and run: ./configure make make check make install without any problems. I've also downloaded GeoIP.dat.gz and GeoLiteCity.dat.gz, unzipped them and put them in a local directory. Then I've set the following paths in my settings.py: GEOIP_PATH = 'path_to_dat_files' GEOIP_LIBRARY_PATH = 'path_to_c_files' Now I'm trying to run python manage.py migrate (which has a reference to GeoIP in a project I'm using), but I'm still getting this error: from django.contrib.gis.utils import GeoIP ImportError: cannot import name GeoIP Any ideas? Thanks.

  Read the article

• Outbound HTTP performance tuning recommendations

  - by Richard Gadsden

  I'll detail my exact setup below, but general recommendations for a better web-browsing experience will be useful. A nice checklist of things to try would be great! I have 600 users on a single site with an 8MB leased line. I get a lot of moans about the performance of "the internet" (ie web-browsing). What recommendations do the community have for speeding things up without just throwing more bandwidth at it? I expect I will end up buying some more, but good management tips are always valuable. My setup is this: Cisco PIX (515E) firewall on the edge of the network. It's just doing some basic NAT, and opening up a handful of ports to various bastion hosts (aka DMZ servers). The DMZ is just a switch that the servers are plugged into. ISA 2006 Enterprise array (two servers) connecting DMZ to the internal LAN, with WebSense Web Security filtering HTTP traffic so users can't look at porn or waste bandwidth on YouTube during working hours. I've done a few things - I've just switched my internal DNS over to use root hints, which halved DNS query latency from 500ms to 250ms. Well worth doing. I'm trying to cache more aggressively, but so much more of the internet is AJAXy and doesn't cache very well as compared to five years ago. Plus the 70GB of cache which felt like a lot a few years ago really isn't any more. I'm getting about 45% cache hits by number of requests, but only about 22% by size, ie larger objects are less likely to be cached. Latency seems to be part of the problem. Is that attributable to the bandwidth problem, or are there things I can look at to try to reduce latency even on heavily-loaded bandwidth?

  Read the article

• Sharepoint tagging like serverfault?

  - by Richard E

  Does a Sharepoint plug-in / add-in exist that will support serverfault-style tagging for documents? Key features: Users can add their own tags just by typing them Autocompletion whilst typing shows the user what tags already exist

  Read the article

• Repeated Reporting Services Login issue when deploying through BIDS to a remote server

  - by Richard Edwards

  We are having a problem deploying a reporting services report to a sql reporting services computer that is configured in SharePoint Integrated mode. I can successfully deploy to the SharePoint document libraries set up for reports and data connections if I do it locally from the box that SharePoint and Reporting Services are deployed on. If I try and do the same thing with the exact same deployment properties from a remote box, I constantly get a Reporting Services Login dialog popping up and no combination of domain\username and password will work. I've even tried the machines local admin account and still nothing. Any ideas where to start looking?

  Read the article

• "You need to confirm this operation" message when trying to delete a file

  - by Richard West

  I'm trying to delete a few files that I created, and I have full permissions on, on a Windows 2008 system. The files are within a folder that I created so they are not system files of any kind. The message box that pops up when I try to delete the file is titled "Destination Folder Access Denied", and the message is "you need to confirm this operation", with a continue, skip or cancel button. I disabled UAC and rebooted to see if this would make the message go away -- it did not. However, with UAC disabled I am able to click on continue and the files are deleted. With UAC enabled I had to provide elevated credientials before the files would delete. What causes this behaviour and how can I remove it?

  Read the article

• Application losing Printer within Terminal Services for remote users

  - by Richard

  Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

  Read the article

• Coloring The Z Shell[closed]

  - by Richard

  Because I have to stare at my command prompt all the time on my computer, it should look at least half-decent, so I am trying to get it colored. The expected outcome is as seen on this site. I have the colors I want set in my .Xdefaults file, but they of course do not color my prompt. My .zshrc is Phil's Prompt. My .Xdefaults is: *background: #121212 !black xterm*color0: #353535 xterm*color8: #666666 !red xterm*color1: #AE4747 xterm*color9: #EE6363 !green xterm*color2: #556B2F xterm*color10: #9ACD32 !brown/yellow xterm*color3: #DAA520 xterm*color11: #FFC125 !blue xterm*color4: #6F99B4 xterm*color12: #7C96B0 !magenta xterm*color5: #8B7B8B xterm*color13: #D8BFD8 !cyan xterm*color6: #A7A15E xterm*color14: #F0E68C !white xterm*color7: #DDDDDD xterm*color15: #FFFFFF *foreground: #DDDDDD Help will be appreciated.

  Read the article

• VMware vSphere Hypervisor 5 with Intel SPL 5000 in Raid 0 no boot from DVD?

  - by Richard

  I hope this is the correct StackExchange, since I am only using StackOverflow for Web development, but need some help with my server configuration. I would like to install VMware vSphere Hypervisor 5 on my server here at home and run a view machines on it such as Windows Server 2008 and Red Hat. I used to have either OpenSuse or Windows Server 2008 installed but I would like to get into VMWare Hypervisor. My hardware configuration: - Intel S5000PSL with bios version S5000.86B.10.60.0091 build date 10/09/2008 as of read out of bios - E5420 @ 2.5GHz Intel Xeon CPU The Intel Virtualization Technology is enabled in the BIOS - DVD DH20A4P DVD Writer - 8GB ECC Ram I have configured a RAID 0 on my 2 WD 2TB SATA drives I have burned the Hypervisor 5 on an empty DVD and it is bootable, I tested it on my client PC. The main problem here is basically, that I cannot boot the DVD on my server. I have set the Boot Option to the DVD drive. I have booted from the BIOS straight in the DVD drive and it does not work. I do not see any error messages. The only thing I see are the PXE error messages when it tries booting from the network and other devices, obviously without any result. Does anybody know why I cannot boot the DVD? What could cause the problem? I have sucessfully installed Windows Server 2008 via original DVD about 1 year ago, so the DVD drive can read and does work. The DVD drive is available in the BIOS and I have checked all cables and none of them is loose in any way. I even see the light flashing but it does not want to boot from the DVD. I am looking forward to suggestions and things that I should check. Thank you very much

  Read the article

• PPTPD with PAM authentication?

  - by Richard

  I need a VPN solution for my company. One requirement is to be able to use the built-in windows VPN client. We are running a Debian Etch server. I've managed to set up PPTPD but the authentication is based on the chap-secrets file. We already have all the user accounts set up on the server, so it'd be nice to use PAM authentication to get user/pass directly from the unix login. Is this possible to achieve and how? If not, is there any other VPN solution that can do this? Don't tell me OpenVPN, it needs additional software to be installed on the Windows machines. :)

  Read the article

• E-mail hosting provider that can set up aliases with wildcards

  - by Richard Downer

  I am looking for an e-mail hosting provider that allow e-mail aliases containing wildcards. In more detail: I own my own domain. I want an e-mail hosting provider to manager e-mail for my domain. Now, to help deal with spam, I often give different e-mail addresses to different organisations. These e-mail addresses always start with the same prefix, but then differ. So, for example, I might give out these e-mail addresses: [email protected] [email protected] [email protected] I want to be able to go to the e-mail provider's control panel and set up an e-mail alias like this: [email protected] -- bounce/discard (because this address has been sold to spammers) joe-*@sample.com -- redirect to [email protected] What's I don't want to do is either have to set up every single e-mail address individually (because I make them up whenever I need them), nor do I want to have a general catch-all for any unrecognised address in my domain (because I don't want to be carpet-bombed with spam when a spammer runs a dictionary attack against my domain name.) Although this seems like a useful feature to have, it seems to be a little-known feature and I've not seen anybody advertise this feature. My current hosting provider offer this but I want to move away from them, so I need another provider that will continue to work with all the e-mail addresses I've been using for years. Alternatively, I could use mail server software that runs on Windows - I have seen some commercial packages offering this feature but they cost more than I can afford - are there any suggestions for low-cost software packages?

  Read the article

• How to diagnose repeated "Starting up database '<dbname>'"

  - by Richard Slater

  I have a SQL 2008 server which is predominantly used as a development server, in the last two weeks it has been having occasional "fits", I have isolated the cause of these fits as CHECKDB being run almost continuiously, the following log information is logged to the Windows Event Log (Source: MSSQLSERVER, Category: Server): Event: 1073758961, Message: Starting up database 'DBName1'. Event: 1073758961, Message: Starting up database 'DBName2'. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. This is repeated every 1-2 seconds untill SQL Server is restarted or the offending databases are detatched. I initially thought that it was a problem with the databases so I took a backup and restored them to a SQL Express instance, all of the data is in tact, and CHECKDB runs without problem. The two databases that were causing a problem last week were not being used; so I took full backups of them and detached the databases, this resolved the problem. However at 0100 GMT this morning to other totally unrelated databases started showing the same problems. There is nothing in the event log to suggest that something happened to the server such as a restart, there are no messages about processes crashing or issues being detected with the storage controller. Speaking to the owner of the company this computer has suffered from "gremlins" in the past, however advice was taken and the motherboard was replaced and the computer rebuilt, memory and processor are the same. Stats: O/S: Windows 2008 Standard Build 6002 CPU: 2x Pentium Dual-Core E5200 @ 2.5GHz RAM: 2GB SQL: 2008 Standard 10.0.2531 Edit: someone posted then deleted a comment about AutoClose, it was turned on on the databases affected. It seems that best practice is to disable it so I have done that with the folllowing. EXECUTE sp_MSforeachdb 'IF (''?'' NOT IN (''master'', ''tempdb'', ''msdb'', ''model'')) EXECUTE (''ALTER DATABASE [?] SET AUTO_CLOSE OFF WITH NO_WAIT'')' I won't know if the problem recurs for some time so I am still open to further answers.

  Read the article

• How can I manually install pecl_http on Ubuntu 9.10?

  - by Richard

  This is essentially a repost of http://stackoverflow.com/questions/4159369/ubuntu-9-04-pecl-extension-downloads-but-does-not-install. Hoping maybe someone can help me here. I've done this: sudo apt-get install php-pear sudo apt-get install php5-dev sudo apt-get install libcurl3-openssl-dev which installs fine. However, the next step: sudo pecl install pecl_http Doesn't install the extension, but merely downloads it. There are no error messages. So I have unpacked it and built it myself per http://php.net/manual/en/install.pecl.phpize.php Essentially: cd pecl_http phpize ./configure make make install I also make test'd to check all ok - and it failed one test: HttpRequest, which is kind of fundamental to this package. And indeed this doesn't work: $r = new HttpRequest('http://www.google.com'); $r->send; echo $r->getResponseCode(); No request is sent, the response code is zero, but no errors either. How can I get this damn thing installed? Is this a bug? Am I doing something wrong? Any alternatives, workarounds? Help appreciated. Thanks

  Read the article

• Using Juniper EX3300 as a router

  - by Richard Whitman

  So I have a Juniper EX3300 Switch. One of its uplink ports (ge-0/1/0) is connected to my ISP's router. ISP router's port address is xx.xx.xx.109. My switch's IP address is xx.xx.xx.110. From the switch, I can ping to xx.xx.xx.109 and any other IP in the world. I mean its connected to the Internet. I connected the port eth0 of a computer (running Ubuntu) to the port ge-0/0/0 of the switch (which in the same VLAN as ge-0/1/0). I configured the port eth0 as follows: iface eth0 inet static address yy.yy.yy.208 netmask 255.255.255.240 gateway xx.xx.xx.110 yy.yy.yy.208 is assigned to me by the ISP. So, now I can ping to the switch (xx.xx.xx.110) from this computer. But I can not ping to either xx.xx.xx.109 (ISP router) or any other IP. I want this computer to be connected to the Internet. What am I doing wrong? Here are some of the configurations on my switch: interfaces { ge-0/0/0 { unit 0 { family ethernet-switching; } } . . . ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family ethernet-switching { port-mode access; } } } . . . vlan { unit 0 { family inet { address 10.0.1.1/24; } } unit 1 { family inet { address xx.xx.xx.110/30; } } } } . . . routing-options { static { route 0.0.0.0/0 { next-hop xx.xx.xx.109; retain; } } } vlans { Cogent { vlan-id 3; interface { ge-0/1/0.0; ge-0/0/0.0; ge-0/0/1.0; ge-0/0/2.0; ge-0/0/3.0; } l3-interface vlan.1; } TFLan { vlan-id 2; interface { ge-0/0/5.0; ge-0/0/6.0; ge-0/0/7.0; ge-0/0/8.0; ge-0/0/9.0; ge-0/0/10.0; ge-0/0/11.0; ge-0/0/12.0; ge-0/0/13.0; ge-0/0/14.0; ge-0/0/15.0; ge-0/0/16.0; ge-0/0/17.0; ge-0/0/18.0; ge-0/0/19.0; ge-0/0/20.0; ge-0/0/21.0; ge-0/0/22.0; ge-0/0/23.0; ge-0/0/4.0; } l3-interface vlan.0; } }

  Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >