Search Results

Search found 24951 results on 999 pages for 'default scope'.

Page 190/999 | < Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >

• Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

  - by Donal

  I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

  Read the article

• Custom validation summary

  - by Robert Morgan

  I'm using the UpdateModel method for validation. How do I specify the text for the error messages as they appear in the validation summary? Sorry, I wasn't entirely clear. When I call UpdateModel(), if there is parsing error, for example if a string value is specified for a double field, a "SomeProperty is invalid" error message is automatically added to the ModelState. How do I specify the text for said automatically generated error message? If I implement IDataErrorInfo as suggested, it's error message property gets called for every column, regardless of whether the default binder deems it valid or not. I'd have to reimplement the parse error catching functionality that I get for free with the default binder. Incidentally, the default "SomeProperty is invalid" error messages seem to have mysteriously dissappeared in the RC. A validation summary appears and the relevant fields are highlighted but the text is missing! Any idea why this is? Thanks again and I hope all this waffle makes sense!

  Read the article

• Deploy CakePHP to a subfolder

  - by mgroves

  I have created a CakePHP 2 app, and now I'm trying to deploy it to a production web server. My app uses the default folder structure (app/lib/plugins/vendors), default htaccess, default routing, nothing special. I've been developing locally as if the app were in the root folder of the site (e.g. http://mycakeapp.localhost/ takes me to the site). But I'm deploying to a site (shared hosting) where that will not be the case (e.g. http://www.somedomain.com/mycakeapp). It doesn't work (I didn't really expect it to), so I assumed I had to tweak one or more htaccess files. I tried modifying the root .htaccess as suggested in this post, but that only partially worked (the link to the CSS didn't work, for instance): <IfModule mod_rewrite.c> RewriteEngine on RewriteRule ^mycakeapp$ mycakeapp/app/webroot/ [L] RewriteRule ^mycakeapp/(.*)$ mycakeapp/app/webroot/$1 [L] </IfModule> So what should I do to all the htaccess files to make this CakePHP site work in a subfolder?

  Read the article

• Django says the "id may not be NULL" but why is it?

  - by Oli

  I'm going crazy today. I just tried to insert a new record and it threw back a "post_blogpost.id may not be NULL" error. Here's my model: class BlogPost(models.Model): title = models.CharField(max_length=100) slug = models.SlugField(max_length=100) who = models.ForeignKey(User, default=1) when = models.DateTimeField() intro = models.TextField(blank=True, null=True) content = models.TextField(blank=True, null=True) counter = models.PositiveIntegerField(default=0) published = models.BooleanField(default=False) css = models.TextField(blank=True, null=True) class Meta: ordering = ('-when', 'id') There are a number of functions beneath the model too but I won't include them in full here. Their names are: content_cache_key, clear_cache, __unicode__, reads, read, processed_content. I'm adding through the admin... And I'm running out of hair.

  Read the article

• ASP.Net MVC 2 on nginx/mono 2.8

  - by mace

  Hi, I am trying to setup ASP.Net MVC 2 application on Linux environment. I've installed Ubuntu 10.10 on VirtualBox, then installed Mono 2.8 from sources. After that I have installed nginx and configure it as recommended here. Unfortunately, FastCGI shows me standard error 500 page: No Application Found Unable to find a matching application for request: Host localhost:80 Port 80 Request Path /Default.aspx Physical Path /var/www/mvc/Default.aspx My application is located in /var/www/mvc directory. I've tried to create some stub Default.aspx file and place it in root dir of my application, but it didn't help, same error occured. Thanks.

  Read the article

• Force 'Replace Into' to use a certain index

  - by Bobby

  I have a MySQL (5.0) table with 3 rows which are considered a combined Unique Index: CREATE TABLE `test`.`table_a` ( `Id` int(11) NOT NULL AUTO_INCREMENT, `field1` varchar(5) COLLATE latin1_swedish_ci NOT NULL DEFAULT '', `field2` varchar(5) COLLATE latin1_swedish_ci NOT NULL DEFAULT '', `field3` varchar(5) COLLATE latin1_swedish_ci NOT NULL DEFAULT '', PRIMARY KEY (`Id`), INDEX `IdxUnqiue` (`field1`(5),`field2`(5),`field3`(5)) ) ENGINE=MyISAM; This table should be filled with a REPLACE INTO query: REPLACE INTO table_a ( Field1, Field2, Field3 ) VALUES ( "Test1", "Test2", "Test3" ) The behavior I'd like to see is that this query always overrides the previous inserted row, because IdxUnique is...ahm, triggered. But unfortunately, there's still the primary index which seems to kick in and always inserts a new row. What I get: Query was executed 3 times: +---Id---+---Field1---+---Field2---+---Field3---+ | 1 | Test1 | Test2 | Test2 | | 2 | Test1 | Test2 | Test2 | | 3 | Test1 | Test2 | Test2 | +--------+------------+------------+------------+ What I want: Query was executed 3 times: +---Id---+---Field1---+---Field2---+---Field3---+ | 3 | Test1 | Test2 | Test2 | +--------+------------+------------+------------+ So, can I tell REPLACE INTO to use just a certain Index or to consider one 'more inportant' then another?

  Read the article

• Problem Paging with Post Action in ASP.NET MVC

  - by Lukasz

  I have a page that takes a number of parameters on a form and posts them to an action. It returns a number of search results that need to be paged through. My pager uses ActionLink; <%= Html.ActionLink(i.ToString(), "Basic", new { page = (i - 1) })%> The results comeback as expected but when I click on page two it goes to the default Action, not the one marked with post. The form values do no get submitted again and the results that are shown for page two are the default results not filters with the parameters. I am not sure how to solve this problem? One way was to save the form values into the database on the post and reading them back on the default action but it seems overkill. Thank You!

  Read the article

• Using Ant to merge two different properties files

  - by Justin

  I have a default properties file, and some deployment specific properties files that override certain settings from the default, based on deployment environment. I would like my Ant build script to merge the two properties files (overwriting default values with deployment specific values), and then output the resulting properties to a new file. I tried doing it like so but I was unsuccessful: <target depends="init" name="configure-target-environment"> <filterset id="application-properties-filterset"> <filtersfile file="${build.config.path}/${target.environment}/application.properties" /> </filterset> <copy todir="${web-inf.path}/conf" file="${build.config.path}/application.properties" overwrite="true" failonerror="true" > <filterset refid="application-properties-filterset" /> </copy> </target>

  Read the article

• Where can I learn about JNDI strings?

  - by ferrari fan

  How do you know how to form a JNDI string? I know there must be a format and that the divisions must mean something but I haven't been able to find a good resource that explains them. For example: java:comp/env/wm/default. This is supposed to connect to a WorkManager in Websphere with the name of default. But what does the "java", "comp", "env" mean? I know what the wm/default mean because that's the JNDI name put in the WorkManager, but what does the rest mean? Thanks

  Read the article

• Useful links

  - by Madhan ayyasamy

  Difference between STI vs Polymorphic associationsSTI vs PolymorphicDifference between habtm vs has_many :throughhabtm vs throughCapistrano Guide linkCapistrano guideRails application without database stuffclass Car < ActiveRecord::Baseself.abstract = trueendAnother link: rails without databaseNamed scope useful linkNamed scopeDifference between http and https verbhttp vs httpsRails 2.3 useful guide websiterails 2.3 guide

  Read the article

• How to debug when CakePHP Model::save() doesn't attempt an INSERT

  - by RyOnLife

  I am having a bear of a time saving the simplest record from a model called ItemView: if($this->save($this->data)) { echo 'worked'; } else { echo 'failed'; } Where $this-data is: Array ( [ItemView] => Array ( [list_id] => 1 [user_id] => 1 ) ) And my table is: CREATE TABLE IF NOT EXISTS `item_views` ( `id` int(11) NOT NULL auto_increment, `list_id` int(11) NOT NULL, `user_id` int(11) default NULL, `user_ip` int(10) unsigned default NULL, `created` datetime NOT NULL, PRIMARY KEY (`id`) ) ENGINE=MyISAM DEFAULT CHARSET=utf8 ROW_FORMAT=FIXED AUTO_INCREMENT=1 ; Looking at the query dump in debug mode, Cake isn't even attempting an INSERT, so I have no idea how to debug. Any help would be appreciated.

  Read the article

• Split user.config into different files for faster saving

  - by HorstWalter

  In my c# Windows Forms application (.net 3.5 / VS 2008) I have 2 settings files resulting in one user.config file. One setting file consists of larger data, but is rarely changed. The frequently changed data are very few. However, since the saving of the settings is always writing the whole (XML) file it is always "slow". SettingsSmall.Default.Save(); // slow, even if SettingsSmall consists of little data Could I configure the settings somehow to result in two files, resulting in: SettingsSmall.Default.Save(); // should be fast SettingsBig.Default.Save(); // could be slow, is seldom saved I have seen that I can use the SecionInformation class for further customizing, however what would be the easiest approach for me? Is this possible by just changing the app.config (config.sections)?

  Read the article

• Cross-platform configuration, options, settings, preferences, defaults

  - by hippietrail

  I'm interested in peoples' views on how best to store preferences and default settings in cross-platform applications. I primarily work in Perl on *nix and Windows but I'm also interested in the bigger picture. In the *nix world "dotfiles" (and directories) are very common with system-wide or application default settings generally residing in one path and user-specific settings in the home directory. Such files and dirs begin with a dot "." and are hidden by default from directory listings. Windows has the registry which also has paths for defaults and per-user overrides. Certain cross-platforms do it their own way, Firefox uses JavaScript preference files. Should a cross-platform app use one system across platforms or say dotfiles on *nix and registry on Windows? Does your favourite programming language have a library or module for accessing them in a standard way? Is there an emerging best practice or does everybody roll their own?

  Read the article

• How to troubleshoot ethernet port on laptop

  - by Psallas Vassilios

  I have a problem with my wired connection. To be more specific, my laptop doesn't seems to recognize that I have plugged in an ethernet cable. I tried to download new drivers for my ethernet card, but I couldn't find any solutions. Maybe because I am new to Linux, so I'm not familiar with running commands in the terminal. OK I have typed the command and here are the results: 00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02) For the second reply I don't know if the following is what you asked me: ?Memory: 3.9 GiB ?Processor: Intel Core 2 Duo CPU P8800 @ 2.66GHz × 2 ?OS type: 32-bit My Ethernet connection had some problem on Windows too. I have changed recently my internet provider, and since then my ethernet cable is not recognized by the laptop. At that time I was still on Windows. I thought that with Ubuntu the problem would be solved, but unfortunately the problem still persists. If someone can help me to solve my problem I'll be thankful. Here are the results of the three first commands you told me to run: lsmod | grep sis190 sis190 22570 0 sudo modprobe sis190 ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:90:81:7e UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:185 errors:0 dropped:0 overruns:0 frame:0 TX packets:185 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22672 (22.6 KB) TX bytes:22672 (22.6 KB) wlan0 Link encap:Ethernet HWaddr 00:25:d3:2c:3a:ae inet addr:192.168.1.72 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe2c:3aae/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:260 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:71992 (71.9 KB) TX bytes:52000 (52.0 KB) and the results of running the last two commands: dmesg | grep -e eth -e sis190 [ 0.816667] sis190: sis190 Gigabit Ethernet driver 1.4 loaded [ 0.816728] sis190 0000:00:04.0: setting latency timer to 64 [ 0.816751] sis190: 0000:00:04.0: Read MAC address from EEPROM [ 0.904032] sis190: 0000:00:04.0: Realtek PHY RTL8201 transceiver at address [ 1.416030] sis190: 0000:00:04.0: Using transceiver at address 1 as default [ 1.448235] sis190 0000:00:04.0: eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at f8410000 (IRQ: 19), 00:90:f5:90:81:7e [ 1.448238] sis190 0000:00:04.0: eth0: GMII mode. [ 1.448243] sis190 0000:00:04.0: eth0: Enabling Auto-negotiation [ 11.560907] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372019] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372265] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.424038] sis190 0000:00:04.0: eth0: auto-negotiating... nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: sis190 State: unavailable Default: no HW Address: 00:90:F5:90:81:7E Capabilities: Carrier Detect: yes Wired Properties Carrier: off

  Read the article

• About enumerations in Delphi and c++ in 64-bit environments

  - by sum1stolemyname

  I recently had to work around the different default sizes used for enumerations in Delphi and c++ since i have to use a c++ dll from a delphi application. On function call returns an array of structs (or records in delphi), the first element of which is an enum. To make this work, I use packed records (or aligned(1)-structs). However, since delphi selects the size of an enum-variable dynamically by default and uses the smallest datatype possible (it was a byte in my case), but C++ uses an int for enums, my data was not interpreted correctly. Delphi offers a compiler switch to work around this, so the declaration of the enum becomes {$Z4} TTypeofLight = ( V3d_AMBIENT, V3d_DIRECTIONAL, V3d_POSITIONAL, V3d_SPOT ); {$Z1} My Questions are: What will become of my structs when they are compiled on/for a 64-bit environment? Does the default c++ integer grow to 8 Bytes? Are there other memory alignment / data type size modifications (other than pointers)?

  Read the article

• No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

  - by jrosell

  Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

  Read the article

• Asp.net help It gives error in home page only

  - by vikram

  i am new to asp.net. I have uploaded a site in ftp. except default.aspx remaining pages working. when i navigate to home page i.e Default.aspx it shows an error Server Error in '/' Application. The resource cannot be found. Description: HTTP 404. The resource you are looking for (or one of its dependencies) could have been removed, had its name changed, or is temporarily unavailable. Please review the following URL and make sure that it is spelled correctly. Requested URL: /Default.aspx Version Information: Microsoft .NET Framework Version:2.0.50727.3607; ASP.NET Version:2.0.50727.3082 Please help. I am stuck here itself. Thanks in advance

  Read the article

• What marketplace / garage-sale software package does togoparts.com use?

  - by gus

  See: OpenSource Marketplace Platform I want to start a site also for end-users to buy/sell used sporting goods of a particular type. When the scope of goods is narrowed like this, it is very advantageous to be able to filter by Brand, Size, Price Range, etc. Nice features: account reputation with user comments listings sortable by many custom fields auto resize and recompress image uploads I don't want to reinvent the wheel, so does anyone know where I can start?

  Read the article

• Using Response.Redirect() to a relative path.

  - by Bryan

  I'm working with ASP.net. My website is hosted within a subfolder test under the IIS root directory. So the url of default.aspx is http://localhost/test/Default.aspx. From default.aspx, I want to use Reponse.Redirect() with a relative path to redirect to another url within the same web site, http://localhost/test/whatever. I tried Response.Redirect("/hello"); and Response.Redirect("~/hello"); Both of them redirect to http://localhost/whatever. Note that the Redirect method use http://localhost instead of http://localhost/test/ as the base url. Any ideas? Thanks.

  Read the article

• Clean install of IIS 6 on Windows Server 2003 ignoring 'web.config'?

  - by Vario

  Hi, Any help with this would be really appreciated! As the title suggests, I'm running a brand new install of Windows Server 2003 and IIS 6 and I'm basically attempting to mirror a live web server onto a new internal development server, which runs the same setup. It's an ASP.NET site that relies heavily on URL rewriting (using Intelligencia). ASP.NET is set to run on v2.0.50727 on both servers. I've tried intentionally introduce syntax errors into the web.config and it just appears to be ignoring them completely, so given IIS 6 doesn't read the web.config, the rest of the site doesn't work at all (I get a 404 error, as a 'Default.aspx' doesn't exist since the web.config handles the default page rewriting). Having looked at the Application Mapping, '.config' files are set to use the default 'c:\windows\microsoft.net\framework\v2.0.50727\aspnet_isapi.dll' which exists. Is there anything else I may be missing? Thanks in advance.

  Read the article

• How to reenable event.preventDefault?

  - by Richbits

  I have a web page which I have prevented the default action on all submit buttons, however I would like to re-enable default submit action on a button how can I do this? I am currently preventing the default action using the following: $("form").bind("submit", function(e){ e.preventDefault(); }); I have successfully done this using the following: $(document).ready(function(){ $("form:not('#press')").bind("submit", function(e){ e.preventDefault(); }); But can I do this dynamically when the button is clicked?

  Read the article

• Difficulty creating a paging function with MySQL and ColdFusion

  - by Mel

  I'm trying to create pagination for search results using MySQL and ColdFusion. My intention is to only retrieve the queries that can be displayed on a single page, thus making the process efficient. I tried using two queries in my function, but I could not return two variables to the cfinvoke. The following code does not paginate, but it displays the result search results using a CFC: <!---DEFINE DEFAULT STATE---> <cfparam name="variables.searchResponse" default=""> <cfparam name="URL.titleName" default=""> <cfparam name="URL.genreID" default=""> <cfparam name="URL.platformID" default=""> <!---TitleName can only be blank if one or both genre and platform are selected---> <cfif StructKeyExists(URL, "searchQuery") AND (Len(Trim(URL.titleName)) LTE 2 AND Len(URL.genreID) IS 0 AND Len(URL.platformID) IS 0)> <cfset variables.searchResponse = "invalidString"> <cfelseif StructKeyExists(URL, "searchQuery")> <cfinvoke component="gz.cfcomp.test" method="searchGames" returnvariable="resultData" argumentcollection="#URL#"> <cfset variables.searchResponse = "hasResult"> </cfif> <cfif searchResponse EQ "hasResult" AND resultData.RecordCount EQ 0> <cfset variables.searchResponse = "noResult"> </cfif> Using this logic, I can display what I need to display on the page: <cfif searchResponse EQ "invalidString"> <cfoutput>Invalid search</cfoutput> </cfif> <cfif searchResponse EQ "noResult"> <cfoutput>No results found</cfoutput> </cfif> <cfif searchResponse EQ "hasResult"> <cfoutput>Display Results</cfoutput> </cfif> If I were executing the queries on the same page, it would be easy to follow the many tutorials out there. But the queries are executing in a function. Displaying the data is easy, but paginating it has become a nightmare for me. Here is my function: <cffunction name="searchGames" access="public" output="false"> <cfargument name="titleName" required="no" type="string"> <cfargument name="genreID" required="no" type="string"> <cfargument name="platformID" required="no" type="string"> <!--- DEFINE LOCAL VARIABLES---> <cfset var resultData = ""> <!---GET DATA---> <cfquery name="resultData" datasource="myDSN"> SELECT * <!---JOINS FOR GENRE/PLATFORM GO HERE---> WHERE <!---CONDITIONS GO HERE---> </cfquery> <!---RETURN VARIABLE---> <cfreturn resultData> </cffunction> To paginate, I thought about modifying my function to the following (a new query using a count statement): <!--- DEFINE LOCAL VARIABLES---> <cfset var resultCount = ""> <!---GET DATA---> <cfquery name="resultCount" datasource="myDSN"> SELECT COUNT(gameID) AS rowsFound FROM GAMES <!---JOINS FOR GENRE/PLATFORM GO HERE---> WHERE <!---CONDITIONS GO HERE---> </cfquery> <!---RETURN VARIABLE---> <cfreturn resultCount> Then I figured if there is a result to return, I would execute a nested query and create the pagination variables: <cfif resultCount.rowsFound GTE 0> <cfparam name="pageNumber" default="1"> <cfset var recordsPerPage = 5> <cfset var numberOfPages = Int(resultCount.RecordCount / recordsPerPage)> <cfset var recordsToSkip = pageNumber * recordsPerPage - recordsPerPage> <!---DEFINE LOCAL VARIABLE---> <cfset var resultData = ""> <cfquery name="resultData" datasource="myDSN"> <!---GET DATA AND SEND IT BACK USING LIMIT WITH #recordsToSkip# and #RecordsPerPage#---> </cfquery> <!---RETURN VARIABLE---> <cfreturn resultData> </cffunction> I figured I would return two variables: resultCount and resultData. I would use #resultCount# to build my pagination, and #resultData# to display the output. The problem is I can't return two variables in the same cfinvoke tag. Any ideas of how to approach the the right way? I'm totally lost as to the logic I need to follow.

  Read the article

• Youtube python: get thumbnail

  - by dkgirl

  Is there a simple way to get the default thumbnail from a youtube entry object gdata.youtube.YouTubeVideoEntry? I tried entry.media.thumbnail, but that gives me four thumbnail objects. Can I always trust that there are four? Can I know which is the default thumbnail that would also appears on the youtube search page? And how would I get that one? Or do I have to alter one of the other ones? When I know the video_id I use: http://i4.ytimg.com/vi/{{video_id}}/default.jpg so, it would also be helpful to get the video_id. Do I really have to parse one of the url's to get at the video_id ? It seems strange that they don't provide this information directly.

  Read the article

• Unable to relate two MySQL tables (foreign keys)

  - by KPL

  Hello people, Here's my USER table CREATE TABLE IF NOT EXISTS `users` ( `id` int(11) NOT NULL AUTO_INCREMENT, `username` varchar(100) NOT NULL, `expiry` varchar(6) NOT NULL, `contact_id` int(11) NOT NULL, `email` varchar(255) NOT NULL, `password` varchar(100) NOT NULL, `level` int(3) NOT NULL, `active` tinyint(4) NOT NULL DEFAULT '1', PRIMARY KEY (`id`,`email`) ) ENGINE=InnoDB DEFAULT CHARSET=latin1 AUTO_INCREMENT=1 ; And here's my contact_info table CREATE TABLE IF NOT EXISTS `contact_info` ( `id` int(11) NOT NULL AUTO_INCREMENT, `name` varchar(255) NOT NULL, `email_address` varchar(255) NOT NULL, `company_name` varchar(255) NOT NULL, `license_number` varchar(255) NOT NULL, `phone` varchar(30) NOT NULL, `fax` varchar(30) NOT NULL, `mobile` varchar(30) NOT NULL, `category` varchar(100) NOT NULL, `country` varchar(20) NOT NULL, `state` varchar(20) NOT NULL, `city` varchar(100) NOT NULL, `postcode` varchar(50) NOT NULL, PRIMARY KEY (`id`,`email_address`), ) ENGINE=InnoDB DEFAULT CHARSET=latin1 AUTO_INCREMENT=1 ; The system uses username to login users.I want to modify it in such a way that it uses email for login. But there's no email_address in users table. I have added foreign key - email in user table(which is email_address in contact_info). How should I query database?

  Read the article

• Hangouts API v1.1 Walkthrough

  Hangouts API v1.1 Walkthrough Introduction to 3 new features in v1.1 of the Hangouts API. This release introduces the ability for your app to respond to face movements in real time. It also provides a new overlay positioned relative to the video feed, new low-latency messages, Hangouts on Air support, the ability to enter any OAuth scope, and a few other miscellaneous features. From: GoogleDevelopers Views: 4425 0 ratings Time: 01:14 More in Science & Technology

  Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >