Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 192/343 | < Previous Page | 188 189 190 191 192 193 194 195 196 197 198 199  | Next Page >

  • windows cache not working as it should?

    - by piotrektt
    I run windows 2012 server with data center. The setup is with 60GB of RAM. I have one file shared on VHD and when I copy this file locally the RAM cache is all used up but when multiple computers connect to the share it the cache is not used. The network is 8Gb. The whole network is around 200 computers that need to read that one file but on this setup only 10 connection kills the server. Is there any way to check what is going on? What other solution can I use to manage cache in windows?

    Read the article

  • PC cannot ping another PC on my home network

    - by Mike C.
    Hello, I am running Windows 7 on my PC, and I am running a Windows 2008 Server VM in Windows Virtual PC. Both machines have network connectivity. However, I cannot ping the VM from the host neither by computer name nor IP. I can ping the host machine from the VM both by computer name and IP. Is there something I need to enable on the VM to allow it to be seen by other machines on my network? Thanks!

    Read the article

  • Network on linux server is periodically down

    - by Fabian
    I have an old server running Fedora 4 that occasionally just stops responding via network for about an hour. This happens 1-2 times a week. Also no connection from the server itself to any other computer on the network is possible when it happens. The network settings and routes look fine. There are no unusual log messages and no unusual processes running at that time. If I restart the network or just do an ifconfig eth0 down & ifconfig eth0 up it works fine afterwards. I know that the server should be updated to a currently supported OS, but that is not really an easy option right now. Any ideas on how I could diagnose and fix that problem?

    Read the article

  • How to fix unstable RJ45 jacks? [closed]

    - by BeemerGuy
    This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

    Read the article

  • belkin wireless router connection drops for ~60sec every ~15 mins

    - by j j
    Hi, I have a belkin wireless-g router, model F5D7230-4. about every 10-15 minutes, for about 1-1.5 mins I won't be able to browse any web sites. during this period, I usually get replys from "ping google.com". maybe 4/5 times I'll get a reply, 1/5 times i don't. I have changed the router DNS entries from "get DNS server from ISP" to 8.8.8.8, google's DNS and that hasn't fixed the situation. This happens on several computers, running windows7, xp, ubuntu, and a mac, so it is definitely NOT an issue with a computer configuration. any ideas?

    Read the article

  • Bridging two connections in windows 7

    - by Serban Razvan
    I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop. Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet. Does anyone knows a solution to this problem? (the connections must be bridged because I want to have only one network in the house)

    Read the article

  • unable to connect to remote sql server from SHDSL router

    - by user529265
    Got a new leased line network to our office that came with a SHDSL router (Watson). Currently, we are unable to use Sql Server management studio to connect to remote Sql databases. It errors out saying A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: TCP Provider, error: 0 - The specified network name is no longer available.) (Microsoft SQL Server, Error: 64) I logged into the Watson management panel and unblocked all the ports for TCP traffic (specified the range as 0 to 60000 and UDP as well - this include 1443 required for connecting to SQL Server). The router is the only thing that has changed. We are able to connect to it from other networks just fine. Is there something we are missing here. Any help would be greatly appreciated.

    Read the article

  • 8 Character Device names

    - by Lee Harrison
    Is there any reason to still use only 8 characters in a device name? My boss still uses this rule for printers, computers, routers, servers... basicly any device connected to our network. This leads to massive confusion among users, especially when it comes to printer. It also leads to confusion from an administration standpoint because every device is named vaguely, and similarly(its only 8 characters!). I understand the history behind this and compatibility with older systems, but none of our legacy systems will ever make use of PS-printers and Wifi networks. Is there any reason to still do this, and what is everyone else doing when it comes to naming network devices at an enterprise level?

    Read the article

  • How frequent are network partitions on cloud services?

    - by roja
    Much is made of the CAP trade-off for data storage where conflicts can be introduced if there is a network partition. My question is there any evidence that this is a problem that arises with any significant frequency in modern cloud IAAS services e.g.; EC2, Azure, Rackspace. Is it a problem which, despite being a theoretical roadblock in constructing idealised distributed systems is, in fact, a non-issue for all practical concerns? Has anyone experienced a network partition within one of these systems (within a single data-centre?) If so would you be willing to share any details?

    Read the article

  • Duplicate name exists solution

    - by user978733
    I have about 70 pc's with exactly same hardware. I decided to automate turning on and off. I took 1 PC. Here is what I've done: Changed bios configuration so that now pc's waking when I turn on AC switch Installed Windows XP and configured so that I can turn off remotelly, changed workgroup name to "WG1", and pc name to "ExamPC" Then created acronis backup image of this pc I installed this image in several PC's and tried to test All worked well till windows opened. The problem is, all tested PC's started Windows nearly at the same time, and all of them popped up error Duplicate name exist. I can't figure out any solution. Any suggestions?

    Read the article

  • PHP application failed to connect after a network plugged back in

    - by tntu
    My data-center appears to have had some issues with their network and thus my server has suffered from on an off network connectivity for about an hour. After the connection has been completely re-established my code still kept reporting the same issue over and over until I have restarted the service. The code is a simple PHP code that loops forever checking the Apple feed-back server and then sleeps for a few minutes and then it begins all over again. Now I understand the error being generated if the network is down but once it got back up why did it continue until I have restarted the code? Does PHP have something that needs to be re-initialized or something?? Messges log: Dec 20 08:57:22 server kernel: r8169: eth0: link down Dec 20 08:57:28 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:29 server kernel: r8169: eth0: link down Dec 20 08:57:33 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:33 server kernel: r8169: eth0: link down Dec 20 08:57:37 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:38 server kernel: r8169: eth0: link down Dec 20 08:57:44 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:44 server kernel: r8169: eth0: link down Dec 20 08:57:52 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:52 server kernel: r8169: eth0: link down Dec 20 09:10:58 server kernel: r8169 0000:06:00.0: eth0: link up PHP Error: PHP Warning: stream_socket_client(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /home/push/feedback.php on line 36 Code Line 36: $apns = stream_socket_client('ssl://feedback.sandbox.push.apple.com:2196', $errcode, $errstr, 60, STREAM_CLIENT_CONNECT, $stream_context);

    Read the article

  • How to install a "virtual" network card on a virtual server?

    - by vikp
    Hi, We have purchased an unmanaged VPS windows hosting solution from one of the UK based companies. We have Windows Server 2008 Standard Edition. We need to install certain third party applications on that server. Unfortunatelly, one of the applications requires a MAC address to be present at all times - this is their way of making sure that software is not pirated (which it isn't). We have tried installing a virtual loopback network card, but this has brought the server down - i.e. we couldn't connect using remote desktop any longer. At the moment we are limited with what we can try. This is an unmanaged solution, therefore any support including restarts is rather costly. Are you aware of any low-risk solutions? Thank you

    Read the article

  • Router intermittently failing

    - by nomen
    My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

    Read the article

  • Is there a way to force/manage file locking in windows?

    - by JPbuntu
    I have a 2 Windows machines networked and I am having trouble with simultaneous access to files. I would like only one user to be able to open a file at a time, which I thought was automatic, using file locks.... if the program used to access the file is locking the file. I believe the problem I am having is some of the programs I use, don't lock the file, and there for can be modified simultaneously by multiple users, which is very much not desired. Currently I am having this problem with only two computers, although as soon as I can figure out a solution to this problem the network is going to be expanded to 6 computers, which will include Windows 7, Vista, and XP, as well as a central file server (Samba). Is there a way to ensure that all files opened in windows get locked? Any suggestions are appreciated, thanks.

    Read the article

  • Best way to split LAN computers on two WANs (not load balancing)

    - by lpfavreau
    What is the best way to split the computers of a LAN (about 50 computers) to go on two WANs, depending on the computers' IP address or computers' configuration (gateway). I'm not looking for load-balancing, I need to be able to route which computer uses which Internet connection. A solution would be to rewire the old office to split the two distinct groups that need to use two different Internet connections but I'm not sure it's worth it at the moment. I have a pfSense router configured with the LAN (DHCP), WAN1 and WAN2. I also have the IP addresses (and ability to configure) the next router on WAN1 and the one on WAN2. What would you suggest? Routing based on IP addresses ranges? Different gateways? VLANs would be difficult for the same reason as to why rewire is a bit complicated. Thanks!

    Read the article

  • Laptops trying to connect via wireless? Only able to connect only via wired connection

    - by Chris J. Lee
    It seems that all the wireless laptops in the office have disconnected and are unable to reconnect to the wifi after a terrible storm caused some power interruptions. Troubleshooting actions Verify wireless broadcasting is up With each laptop i ended up flushing their dns cache on Win 7 (ipconfig /flush ) Performed an ipconfig /all to see what the new ip is Made sure password was correct Reset the router (multiple times) restarted each laptop. Tried connecting wirelessly Am i missing some small detail ? Network information The router is a linksys/cisco WRVS4400N router. Supports a lot of fancy features i don't know how to use. We have 3 static ip's the conference room computer, the wireless printer, my computer Mostly windows machines, we have 3 mac users

    Read the article

  • Unable to set initcwnd on a Hetzner server

    - by Sergi
    We just ordered a bunch of Hetzner EX40SSD servers with the minimal Debian install image that they provide and everything is just fine except that looking at tcpdumps for fine tuning the network from various locations the initcwnd param seems to be stuck at 6 no matter how we change it. By default Debian 3.2 kernels should have that setting to 10 so it's pretty strange. Is it possible that the NIC driver or a custom setting in the Hetzner Debian image is limiting this param? Even if we set it to 4, like the old kernel default, it doesn't work. Any ideas would be much appreciated! Does anyone know if the NIC drivers provided by default by Debian have some kind on limitation. In a long thread in http://www.webhostingtalk.com/showthread.php?t=1200617&highlight=hetzner they talk about a page http://wiki.hetzner.de/index.php/Installation_des_r8168-Treibers/en where Hetzner states that the included Realtek r8168 driver is not working properly, but nowhere do they say that the initcwnd could be affected. Tomorrow i will try to install a CentOs image and see if Debian is the problem...Last resort would be to install a custom debian image, but that is a pain in the ass! Thanks!

    Read the article

  • Windows Vista: TCP/IP stack is smashed, how to reinstall the LAN-Devices?

    - by Ice
    the TCP/IP stack is smashed, thats why no LAN-Connections are running. I want to download the LAN drivers from another computer and uninstall and reinstall the LAN devices on this system. Hopefully that should recreate the stack. But what to download? What uninstall? How to install? Windows Vista is protected against such changes, so how to achieve that job? please help. Update per 2011-03-11: I found all the tipps and hints about "TCP/IP Repair, LSP Fix, and WinSock Fix" according to windows vista but nothing helped to bring back network access. What can i do as next step or which opportunities are left?

    Read the article

  • openVPN as a way to connect to a LAN by another client, different from server

    - by Einar
    Setup: one LAN handled by a router without a publicly available IP address but without any outbound connection restrictions ("target LAN"); a separate server publicly reachable from the Internet ("gateway"). I am trying to set up openVPN so that a third client can connect to the "gateway" and access the "target LAN". As the router of "target LAN" is not reachable from the Internet directly, it connects to the gateway itself via openVPN as well. The problem is how to handle routing. The LAN router has two network interfaces (for the outside network and the LAN itself). In openVPN (the server on the gateway) I set client-to-client and push "route 192.168.10.0 255.255.255.0" but I assume this would be horribly wrong (it actually messed up the routing on the LAN router until I killed openVPN). openVPN is not using bridging, is configured via tun. Other config details from the server server 10.8.0.0 255.255.255.0 client-config-dir ccd route 192.168.10.0 255.255.255.0 And the client file in ccd is iroute 192.168.10.0 255.255.255.0 What can be adjusted to ensure that a third client can connect through openVPN and access the LAN mentioned earlier?

    Read the article

  • Testing the load factor in my lab

    - by Ami Winter
    I am a system admin in a lab, I have ~90 computers in the lab and I want to check the load factor on them.. meaning, to check how many people are working on the computers hourly.. To see if I need to buy more computers or not. I am looking for a way to build a script to check if a computer is logged on or not.. (0 for log off - 1 for log on) After I will have this data, I know how to build a script to build me the graphs. All the computers are linked via a domain and most of them have windows XP (few windows 7) I'll be happy to get some help. Amihay

    Read the article

  • How to connect two subnet with Windows Server?

    - by 9dan
    Hello, I have some work to do in a small office. This office has two separate Internet connections. One is a kind of DSL line and connected through the Internet sharing router (DHCP). One is a leased line with public IP adresses (No DHCP). This leased line provide only 30 IP addresses and the gateway is provided by the ISP. Some workers use private IP provided by the router, some workers use manually setup public IP. There is a Windows 2008 R2 server with two NICs, connected to each lines. I want to connect/merge(?)/bridge(?) two subnet with this server so that users from the different subnet can access each other. How can I accomplish this? Something like, add gateway function to this server and public IP users change the gateway to point this server.. It it possible ? Sorry for my rambling. Thanks in advance.

    Read the article

  • How do I purge or empty Windows Explorer's network username and sharename cache?

    - by Abel
    While troubleshooting a Samba vs Windows Network issue, I noticed that Windows' Explorer remembers login credentials of remote shares, even if you ask it not to. For instance, after accessing a share using \\servername\sharename plus entering username/password and then closing Windows Explorer, adding the same share as a network drive gives the following message, regardless whether the username is the same or not: The network folder specified is currently mapped using a different user name and password. To connect using a different user name and password, first disconnect any existing mappings to this network share. Using NET USE does not show the share. After restarting the computer, I have no problems accessing the share using different credentials. But restarting just for testing other credentials is annoying, esp. while troubleshooting. How can I purge this cache, using Windows Vista? Note: using nbtstat -R[R], ipconfig /renew, killing explorer.exe or disabling / re-enabling the network card didn't help.

    Read the article

  • Why is network utilization so low

    - by dean20007
    My network utilization in windows never seems to get above 1%. This seems absolutely tiny, does anyone know why it is so low and if there is anyway to increase it(or if it indeed does need increased) FYI: I use a D-LINK USB wireless adaptor

    Read the article

< Previous Page | 188 189 190 191 192 193 194 195 196 197 198 199  | Next Page >