Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 193/433 | < Previous Page | 189 190 191 192 193 194 195 196 197 198 199 200  | Next Page >

  • How to setup apache to catch a proxy_pass from nginx?

    - by Paté
    I have a working apache vhost such as <VirtualHost localhost:10006> DocumentRoot "/home/pate/***/git/kohana_site/public/site/" </VirtualHost> <VirtualHost *:10006> ServerName api.* DocumentRoot "/home/pate/***/git/kohana_site/public/api/" LogLevel debug </VirtualHost> If i point to localhost:10006 I get my website and api.localhost:10006 I get my api. Then I have haproxy setup on top of that, that runs on port 10010 and both localhost:10010 and api.localhost:10010 have the expected behaviour. Now I have nginx setup on port 80 with this configuration. server { listen 10000; server_name api.*; location / { proxy_pass http://legacy_server; } } server { listen 10000 default; server_name _; location /nginx_status { stub_status on; access_log off; } # images are accessed via the CDN over HTTP (not https) location /n/image { proxy_pass http://image_caching_server; } location / { return 301 https://$host:10014$request_uri; } } upstream legacy_server { server localhost:10010 fail_timeout=0; } the problem is that apache does not recognize the vhost properly and redirects api.localhost to the website instead of the api. I tried playing with set_proxy_header Host $host but it doesn't seem to do anything.

    Read the article

  • Switch Before Firewall / Router - Multiple public IPs

    - by rii
    I currently Have a 10Mbit Full duplex circuit connected to a small unmanaged switch which then connects to a Sonicwall Firewall / Router. I have several public IP addresses (/28) that are assigned to several devices in my setup. Now the problem is the small switch I have was lent to me and needs to be returned, I have replaced this switch with several other switches but for some reason any other switch I use causes the network to become extremely slow. I believe this is a problem with the autonegotiation of theses hubs, so I am thinking of purchasing a small managed switch (cisco 300 series) and making the receiving port on the swith Explicitly 10Mbit Full Duplex and see if this works. My question is, being that this is a managed switch and needs an IP, will I still be able to run my public ips through it? Say the circuit has 70.80.4.1 - 7 will I still be able to assign 70.80.4.2 to my firewall and 70.80.4.3 to my router connected to some other port in the switch? Will I have to assign the switch a public IP address in this range as well for it to "route" to those other devices or does the switch does not care what IPs goes through it while operating as a Layer 2 Switch? Any help would be greatly appreciated. Thanks in advanced!

    Read the article

  • iptables firewall rules not allowing ssh from lan to DMZ

    - by ageis23
    Chain INPUT (policy ACCEPT) target prot opt source destination REJECT tcp -- anywhere anywhere tcp dpt:www reject-with tcp-reset REJECT tcp -- anywhere anywhere tcp dpt:telnet reject-with tcp-reset ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED DROP udp -- anywhere anywhere udp dpt:route DROP udp -- anywhere anywhere udp dpt:route ACCEPT udp -- anywhere anywhere udp dpt:route logdrop icmp -- anywhere anywhere logdrop igmp -- anywhere anywhere ACCEPT udp -- anywhere anywhere udp dpt:5060 ACCEPT 0 -- anywhere anywhere state NEW logaccept 0 -- anywhere anywhere state NEW ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere logdrop 0 -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT 0 -- 192.168.0.0/24 192.168.2.0/24 reject-with icmp-port-unreachable ACCEPT tcp -- choister 192.168.2.142 tcp dpt:ssh state NEW REJECT 0 -- 192.168.0.0/24 192.168.3.0/24 reject-with icmp-port-unreachable ACCEPT gre -- 192.168.1.0/24 anywhere ACCEPT tcp -- 192.168.1.0/24 anywhere tcp dpt:1723 ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere TCPMSS tcp -- anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU lan2wan 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED logaccept tcp -- anywhere choister tcp dpt:www TRIGGER 0 -- anywhere anywhere TRIGGER type:in match:0 relate:0 trigger_out 0 -- anywhere anywhere logaccept 0 -- anywhere anywhere state NEW logdrop 0 -- anywhere anywhere The ssh server I'm trying to connect to is in the DMZ(192.168.0.145). It's mainly used as a web server. I need access to it from my room 192.168.2.142. I don't get why ssh can't forward onto the 192.168.2.0 subnet? I'm sure it's the reject rule that causing this because it works without it.

    Read the article

  • Apache Virtual Hosts behind Cisco Router

    - by Theo
    I'm setting up an Apache 2.2 Ubuntu web server for internal services that is also supposed to be accessed from outside our LAN. Our LAN has a single external IP that is the external IP of our RV042 Cisco router. We have set up several A records on our external DNS server that point to this IP. Our internal DNS server resolve the same records to the internal IP of our web server, so computers from inside the network can access them using the same address as if they were outside. We forwarded the router's external 80 port to our web server's 80 port. I have set up one Virtual Host for each domain name in our list, and my httpd.conf is something like this: ServerName web.domain.com NameVirtualHost *:80 <VirtualHost *:80> ServerName alfresco.domain.com <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /alfresco http://localhost:8080/alfresco ProxyPassReverse /alfresco http://localhost:8080/alfresco ProxyPass /share http://localhost:8080/share ProxyPassReverse /share http://localhost:8080/share </VirtualHost> <VirtualHost *:80> ServerName crm.domain.com DocumentRoot /var/www/sugarcrm </VirtualHost> Now, this works if we are in our LAN. However, if we are outside of our LAN we reach our web server's default page saying: It Works! This is the default web page for this server. But we can't reach the virtual hosts, as if the domain name is not being preserved when the router forward the packets to the web server. Am I doing something wrong? How can I check what is going on? What should be the settings to make this work from outside?

    Read the article

  • Ubuntu and Windows and Separate HDs, oh my!

    - by LuxuryMode
    Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. Here's a pic of the error I get when I try to boot to Windows: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu. (Someone suggested just reinstalling windows from installation CD. Agree?)

    Read the article

  • Isolating a computer in the network

    - by Karma Soone
    I've got a small network and want to isolate one of the computers from the whole network. My Network: <----> Trusted PC 1 ADSL Router --> Netgear dg834g <----> Trusted PC 2 <----> Untrusted PC I want to isolate this untrusted PC in the network. That means the network should be secure against : * ARP Poisoning * Sniffing * Untrusted PC should not see / reach any other computers within the network but can go out the internet. Static DHCP and switch usage solves the problem of sniffing/ARP poisoning. I can enable IPSec between computers but the real problem is sniffing the traffic between the router and one of the trusted computers. Against getting a new IP address (second IP address from the same computer) I need a firewall with port security (I think) or I don't think my ADSL router supports that. To summarise I'm looking for a hardware firewall/router which can isolate one port from the rest of the network. Could you recommend such a hardware or can I easily accomplish that with my current network?

    Read the article

  • Oracle Error ORA-12560 TNS:Protocol Adapter error?

    - by David Basarab
    I am using Oracle Database 10g. Both Servers are Windows 2003. I have an Orcale Database set up on one server. Here is the TNSNames.ora from the server with the database. # tnsnames.ora Network Configuration File: C:\oracle\product\10.2.0\db_1\network\admin\tnsnames.ora # Generated by Oracle configuration tools. ORCL.VIRTUALHOLD.COM = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = databaseServer)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orcl) ) ) The Environmental Variables on the Server are ORACLE_HOME = C:\oracle\product\10.2.0\db_1 ORACLE_SID = orcl I am trying to connect to it from another box that has Oracle Client installed. Here is the tnsnames.ora installed on the other client server. # tnsnames.ora Network Configuration File: C:\oracle\product\10.2.0\client_1\network\admin\tnsnames.ora # Generated by Oracle configuration tools. ORCL = (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = databaseServer)(PORT = 1521)) ) (CONNECT_DATA = (SERVICE_NAME = orcl) ) ) ORACLE_HOME = C:\oracle\product\10.2.0\client_1 ORACLE_SID = orcl Locally on the database server I can connect to through sqlplus with no issues. On the client machine I keep getting the error: ORA-12560: TNS:protocol adapter error What am I missing? Does the client TNSNames.ora need to be different?

    Read the article

  • System and Router configuration for setting up a home firewall based on Zentyal

    - by Ako
    I am not much of a system administrator, so please be patient if this looks too simple for you. I have a several computers at home, and all of them connect using an ADSL modem/router (and Wireless AP). I have been attacked several times (mainly from Russia and Ukraine), so I thought I should have some kind of firewall, besides the ESET firewall on my Windows 7. So now I have these (new) configuration: I have a small ADSL modem (Zyxel brand) which has only one Ethernet port. This modem is used to connect to internet and is configured in NAT mode. The interface has is configured with IP address 192.168.1.1. I have an old PC and I have installed zentyal on it. It has two Ethernet ports, eth0 and eth1. Eth0 is connected to the Zyxel modem with IP 192.168.1.2 and is checked as the WAN interface (external). I have another ADSL modem which is also a router with 4 Ethernet ports and Wireless AP. One of the Ethernet ports is connected to eth1 on Zentyal box. The Ethernet port's IP is 192.168.2.1 and Zentyal's eth1 is 192.168.2.2. Now, I want to enable other computers to connect to internet through the router both using Wireless and Ethernet. The problem is that I don't know how to configure the router so it routes connections to the Zentyal box. Does anyone have any clue? Again I am sorry if this looks stupid. Thanks.

    Read the article

  • Fortigate restrict traffic through one external IP

    - by Tom O'Connor
    I've got a fortigate 400A at a client's site. They've got a /26 from British Telecom, and we're using 4 of those IPs as a NAT Pool. Is there a way to say that traffic from 172.18.4.40-45 can only ever come out of (and hence go back into) x.x.x.140 as the external IP? We're having some problems with SIP which looks like it's coming out of one, and trying to go back into another. I tried enabling asymmetric routing, didn't work. I tried setting a VIP, but even when I did that, it didn't appear to do anything. Any ideas? I can probably post some firewall snippets if need be.. Tell me what you want to see. SIP ALG config system settings set sip-helper disable set sip-nat-trace disable set sip-tcp-port 5061 set sip-udp-port 5061 set multicast-forward enable end Interesting Sidenote VoIP phones, with no special configuration can register fine to proxy.sipgate.co.uk, which has an IP address of 217.10.79.16. Which is cool. Two phones are using a different provider, whose proxy IP address is 178.255.x.x. These phones can register for outbound, but inbound INVITEs never make it to the phone. Is it possible that the Fortigate is having trouble with 178.255.x.x as it's got a 255 in it? Or am I just imagining things?

    Read the article

  • nginx proxying different servers for different subdomains

    - by The.Anti.9
    i just set up an nginx server. On the same computer as nginx, I have apache running on port 8000 (this was previously set up.) and I want no subdomain and the www. subdomain to go to the local apache instance. But i want the stuff. subdomain to link to my server where i keep all my miscellaneous files (pictures, documents, etc.), which is also listening on port 80 at the ip 192.168.1.102. I tried configuring it, but when i go to my domain, I just get the "Welcome to nginx!". Here's what I have: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; include /etc/nginx/conf.d/*.conf; server { listen 80; server_name theanti9.com www.theanti9.com; access_log /var/log/nginx/access.log; location / { proxy_pass http://localhost:8000; } } server { listen 80; server_name stuff.theanti9.com; access_log /var/log/nginx/access.log; location / { proxy_pass http://192.168.1.102:80; } } } I'm not really sure what's wrong. Any suggestions?

    Read the article

  • Why Would one VLAN have no Communication on one Switch?

    - by Webs
    So the problem is we have a device or host that needs to communicate on a specific VLAN. This VLAN is not new, it is running all throughout our environment and works fine. But the VLAN was recently configured on the switch in question, a Cisco 3750. The DHCP server is handing out addresses on that VLAN with no problem. I have verified the cable between the host and switch and tried multiple hosts, but none of them can communicate or get an address. I plugged my laptop into an empty port which had a different VLAN assigned and immediately got a DHCP address. When I changed that port to the same VLAN I'm having issues with I got the same problem. The laptop just sits there and tries to DHCP an address but nothing happens. I double checked the cores and their Layer 3 VLAN config and its fine too. Plus I figured the issue couldn't be with them because the VLAN works fine everywhere else it exists. So the only other thing I can think of is the switch, but the VLAN exists on the switch and seems to be configured correctly. The trunks appear to be configured just fine as well too. Anyone have any ideas? I'm lost on this one.

    Read the article

  • Wireless Access Point stopped working

    - by Alex Pritchard
    I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

    Read the article

  • Apache mod_proxy

    - by mhouston100
    Uggh, I'm spewing that I can't figure this out, I'm so frustrated: <VirtualHost *:80> servername domain1.com.au ServerAdmin webmaster@localhost DocumentRoot /var/www/html ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined <Proxy *> Order Allow,Deny Allow from all </Proxy> RewriteEngine on ReWriteCond %{SERVER_PORT} !^443$ RewriteRule ^/(.*) https://%{HTTP_HOST}/$1 [NC,R,L] </VirtualHost> <VirtualHost *:443> servername domain1.com.au SSLEngine on SSLCertificateFile /etc/apache2/ssl/owncloud.pem SSLCertificateKeyFile /etc/apache2/ssl/owncloud.key DocumentRoot /var/www/html </VirtualHost> <VirtualHost *:*> Servername domain2.com.au ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / https://192.168.1.12/ ProxyPassReverse / https://192.168.1.12/ </VirtualHost> Not sure if it's clear what I'm trying to do, but I've read and read and READ, I still can't figure it out. Basically I have a working Apache server with a rewrite to force HTTPS, as seen in the first two VirtualHost entries. I now have a webmail service I set up on another server, under another domain name, however I only have one incoming public IP address. So I'm trying to have any incoming requests for the second domain to be proxied to the other server to access the webmail, whether its port 80 or 443. IMAP and POP3 are no problems, I can just forward the ports directly to the correct server. The results of the above configuration is that requests to domain2.com.au (port 80 or 443) are forwarded to https://domain1.com.au. Am I headed in the right direction?

    Read the article

  • Help with Ubuntu and Windows, separate HDs

    - by LuxuryMode
    Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

    Read the article

  • Vagrant VM Fails to Boot

    - by Rob Wilkerson
    I have a Vagrant environment that requires me to forward port 80 so I bring it up under sudo on an OS X machine. This has always been fine until I recently upgraded to Vagrant 1.2.2. Now it fails to boot. [default] Waiting for VM to boot. This can take a few minutes. [default] Failed to connect to VM! Failed to connect to VM via SSH. Please verify the VM successfully booted by looking at the VirtualBox GUI. Because I'm running under sudo, the machine never gets added to the Virtualbox GUI, but that's always been the case for this environment. I don't get any indication that there was a problem with the additions -- a potential source of this error, from what I've read. I can bring things up just fine if I change to using port 8080 on the host machine. I can't use the app, but the VM itself loads up and provisions nicely. As far as I can tell, the only thing that's changed is: I upgraded my Vagrant version I updated the project's Vagrantfile to use v2 syntax. Anyone have any idea what I might be missing? I thought I'd be able to find this pretty easily, but it's quickly becoming a very real problem.

    Read the article

  • How to diagnose issue between mobo, RAID, and SSD cache drive? [migrated]

    - by goober
    Background This issue is happening on my custom-built desktop. Relevant specs: Motherboard: ASUS P8Z68-V PRO Utilizing Intel RST technology (application that uses unused SSD as cache) Processor: Intel core i7-2600k (not overclocked) HDDs: RAID1 of 2x Seagate Barracuda 1TB (ST31000524AS) (RAID performed via z68 chipset) Machine has run fine for ~1 year with no issues, and has been well-maintained (dust, etc.) What Happened Random Freezing issues -- intermittent Looked at the RST application screen to see that the acceleration cache was listed as "unavailable" -- recommended that I power down and reconnect the drive. Reconnected the drive to no avail. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Now, the freeze happens whenever loading something particularly data-driven (a video, a game, etc.) Steps Attempted Reconnected the drive to no avail. Updated Intel RST software to v. 11.6.0.1030 to see if that made a difference. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Connected the drive as its own volume. Formatted it, ran disk check errors -- all seems fine. Reconnected the drive and selected it again as the cache drive. Now, what happens when there is a freeze: Machine freezes I am unable to perform any command Screen then goes black I hit the reset button During boot, all drives show as "Disabled" and I am told no volume can be found I then hit the reset button (or power off/on) again. Either the next time (or sometimes after repeating this once more), the metadata cache is reconstructed and the system boots fine, showing the SSD as a cache. Question I believe this is an issue with the SSD itself, but how can I be sure since connecting it separately appeared to show no problems? I want to make sure it's not an issue with the motherboard, SATA ports, etc.

    Read the article

  • What differences are there between "home" switches and "professional" switches?

    - by pjreddie
    Our radio station uses a PtP wireless system to stream our radio and TV signals from our studio up a hill to our transmitter. We have been having problems with warbly sound and drop outs that come from some point in this system. An engineer that occasionally visits the station thinks it could be the switches we use on each side of the PtP wireless system to connect the PtP devices to the encoders and decoders and wants us to get two of these switches: http://www.amazon.com/Netgear-JGS516-ProSafe-16-Port-Ethernet/dp/B0002CWPOK/ref=dp_return_1 The encoder/decoder setup only streams 8Mbps total so it seems like the switches we have should not be stressed out, unless they are causing sufficient latency to degrade the performance of the encoder/decoder. At each end of the connection we only have 4 connections, is there any reason we couldn't get a cheaper, "home" quality switch like this: http://www.amazon.com/D-Link-DGS-1005G-5-Port-Gigabit-Desktop/dp/tech-data/B003X7TRWE/ref=de_a_smtd Is there a significant difference that we would notice in terms of latency between these two switches? How much does the quality of the switch actually matter in this scenario? Any help is appreciated, feel free to ask questions if anything needs clarification. Thanks

    Read the article

  • Gigabyte H55N-USB3: No video on HDMI

    - by newt
    I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

    Read the article

  • How do I tell Websphere 7 about a front end load balancer so that re-directs are handled correctly?

    - by TiGz
    On WebLogic 11G I can use the console to set the FrontendHost and FrondendPort on a server or on a cluster so that re-directs are handled correctly and end up resolving to the front end load balancer instead of the local host. The MBeans associated with this on WebLogic are, for example: MBean Name com.bea:Name=AdminServer,Type=WebServer,Server=AdminServer Attribute Name FrontendHost Description The name of the host to which all redirected URLs will be sent. If specified, WebLogic Server will use this value rather than the one in the HOST header. Sets the HTTP frontendHost Provides a method to ensure that the webapp will always have the correct HOST information, even when the request is coming through a firewall or a proxy. If this parameter is configured, the HOST header will be ignored and the information in this parameter will be used in its place. Type java.lang.String Readable / Writable RW How is the same thing achieved under Websphere 7? Follow up info: So I have 2 use cases actually. One is that I have a web app running under WebSphere on host A on port 9002 and a LB running on host B at port 80, when I visit the home page of the app via the LB on http://hostb/app the app redirects my browser to http://hostb:9002/app and it 404's I think this is WebSphere's fault but I guess it could be the app's fault? The second is that the web app in question needs to send emails containing URls that the customer can click on to get back into the web app - obviously this needs to be via the LB. On WebLogic the app uses MBeans to derive the LB url and I was hoping to use a similar mechanism on WebSphere.

    Read the article

  • Apache mod_proxy, how to forward request into local network ip(server)

    - by Beck
    Can't figure out, how to configure mod_proxy for this. I have two domains, one is working fine at the moment. Second is bind to the same ip. I need to forward requests from second domain to another server in local network. like that: domain1.com => 192.168.1.101 domain2.com => 192.168.1.102 What configuration or directives i should use? Thanks ;) Update <VirtualHost *:80> ServerName www.domain2.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://192.168.1.103:8080/ ProxyPassReverse / http://192.168.1.103:8080/ </VirtualHost> It just doesn't redirect to second server. That's it. And when i restart apache, it says something with overlapping 80 port. [warn] _default_ VirtualHost overlap on port 80, the first has precedence

    Read the article

  • Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

    - by Nils
    I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

    Read the article

  • Cannot make bind9 forward DNS query to subdomain unless recursive enabled

    - by PP.
    I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

    Read the article

  • Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

    - by Gabble
    I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

    Read the article

  • Is it bad to redirect http to https?

    - by jasondavis
    I just installed an SSL Certificate on my server. I use a web hosting panel called ZPanel that is an open source project. It then set up a redirect for all traffic on my domain on Port 80 to redirect it to Port 443. In other words, all my http://example.com traffic is now redirected to the appropriate https://example.com version of the page. The redirect is done in my Apache Virtual Hosts file with something like this... RewriteEngine on ReWriteCond %{SERVER_PORT} !^443$ RewriteRule ^/(.*) https://%{HTTP_HOST}/$1 [NC,R,L] My question is, are there any drawbacks to using SSL? Since this is not a 301 Redirect, will I lose link juice/ranking in search engines by switching to https? I appreciate the help. I have always wanted to set up SSL on a server, just for the practice of doing it, and I finally decided to do it tonight. It seems to be working well so far, but I am not sure if it's a good idea to use this on every page. My site is not eCommerce and doesn't handle sensitive data; it's mainly for looks and the thrill of installing it for learning. UPDATED ISSUE Strangely Bing creates this screenshot from my site now that it is using HTTPS everywhere...

    Read the article

  • How to setup bindings for development IIS 7.5 with lot of sites

    - by Antonio Bakula
    I am a programmer in a small ASP.NET shop with very little expirience in server administration, and I have to setup IIS 7.5 to host lot of sites on newly installed windows server 2008 R2, these sites are test "clones" for sites on "real" web server and they should be accessible only in local network (domain). Developers should add new sites for our new customers. Project managers use this server to check progress and test new sites and new features, QA people have to have access to this site and test before we copy it to the "real" web server. Developers only have access to IIS console, in fact they can use RDP to test server with their developer domain credentials and permissions, also developers are local admins on that machine (tester). On our previous server I used different port numbers for each site. That worked but don't like this solution, I would prefer to use subdomains. But here are the problems: manually adding DNS records is not an option because we do not wont that developers have to administer domain DNS server, and currently this had to be done with domain administrator credentials. Is there a some way to add DNS record automatically ? I tried to add DNS record for subdomains on test server with wildcard (*.tester) and that seems to work for some time but that change coused some bad problems in our domain network and admin forbid me to mess with DNS, he said that I have to add DNS record for every subdomain manually and that I can not use wildcards, and there is nothing that I can do about it, mainly for "politicall" reasons :( obviously our admin is pretty much uncooperative, outsorced from different organization and I can't do anything about that. can I add another DNS server on that machine ? What must be setup on clients machines to "tell" them to use domain DNS server and tester domain server ? So please I need someone to give me some advice, what should I do ? Is different port numbers only option left ? Thanks !

    Read the article

< Previous Page | 189 190 191 192 193 194 195 196 197 198 199 200  | Next Page >