Search Results

Search found 33760 results on 1351 pages for 'port number'.

Page 194/1351 | < Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

• Multiple Graphics Cards on Fedora 15 (Gnome 3)

  - by Michael

  I have the (delightful) misfortune of having 3 graphics cards. They are XFX Radeon 5750s. Each drives 2 monitors via dvi. I am having a really hard time getting these running on fedora 15 (gnome 3). So my setup is 3 columns of 2 monitors (the upper monitor is mounted upside down in each column to reduce the bezel between monitors). When the (graphical) login screen comes up all 6 have the blue stripey background that must be the default, but then when I login, things get interesting. In the xorg.conf below, you will see only 2 of the screens in the serverlayout while the other 4 are commented out. Logging in with only 2 of the screens active works well (and it even remembers that the top one is upside down, and should be considered above the lower, i am not sure where it stores this info, but i set it using the graphical "Displays" settings) However, as soon as I uncomment a third screen, or more, it gives me an error message when I login. It's one of those friendly, less helpful messages (Oh no! Something has gone wrong. A problem has occurred and the system can't recover. Please log out and try again). If i do not use an xorg.conf, then the "Displays" prefs pane shows only the two monitors on one of my graphics cards Thanks to anyone who can help me get going! (xorg.conf and then lspci below, and xorg log) xorg.conf Section "ServerLayout" Identifier "X.org Configured" Screen "Screen0" 0 0 Screen "Screen1" Below "Screen0" # Screen "Screen2" RightOf "Screen0" # Screen "Screen3" RightOf "Screen1" # Screen "Screen4" RightOf "Screen3" # Screen "Screen5" RightOf "Screen4" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "catalogue:/etc/X11/fontpath.d" FontPath "built-ins" EndSection Section "Module" Load "record" Load "dri" Load "dbe" Load "extmod" Load "dri2" Load "glx" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor3" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor4" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor5" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" Identifier "Card0" Driver "radeon" BusID "PCI:4:0:0" EndSection Section "Device" Identifier "Card1" Driver "radeon" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Card2" Driver "radeon" BusID "PCI:6:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Card0" Monitor "Monitor1" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Card1" Monitor "Monitor2" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen3" Device "Card1" Monitor "Monitor3" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen4" Device "Card2" Monitor "Monitor4" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen5" Device "Card2" Monitor "Monitor5" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection lspci output follows [tgm@tgm ~]$ lspci 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 02:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:02.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 04:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 04:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 05:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 05:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 06:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 06:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) xorg log (posted to fpaste due to how long it is. thanks to marcusw for the request) http://www.fpaste.org/r5ww/ xorg log with all 6 monitors enabled in xorg.conf (they all turn on and have blue, but then one gets the aforementioned user-friendly error message). http://www.fpaste.org/X63H/

  Read the article

• Changes to JBoss web.xml have no effect

  - by sixtyfootersdude

  I just added this to my web.xml on my JBOSS server. But it had no effect. I am still allowed to connect to ports that do not use bi-directional certificate exchange. Anyone have an ideas? <!-- Force SSL for entire site as described here: http://wiki.metawerx.net/wiki/ForcingSSLForSectionsOfYourWebsite --> <security-constraint> <!-- defines resources to be protected (in this case everything)--> <web-resource-collection> <!-- name for the resource, can be anything you like --> <!-- Question: is this referenced anywhere else? --> <web-resource-name> Entire Application </web-resource-name> <!-- protect the entire application --> <url-pattern> /* </url-pattern> </web-resource-collection> <!-- defines protection level for protected resource --> <user-data-constraint> <!-- data cannot be observed or changed --> <!-- how it works in tomcat: --> <!-- if (set to integral or confidential && not using ssl) --> <!-- redirect sent to client, redirecting them to same url --> <!-- but using the port defined in the redirect port --> <!-- attribute in the <Connector> element of server.xml --> <!-- default is 443, so in other words user is redirected --> <!-- to same page using ssl. --> <!-- BUT it is differnt for JBOSS!! See this link: http://wiki.metawerx.net/wiki/ForcingSSLForSectionsOfYourWebsite --> <transport-guarantee> CONFIDENTIAL </transport-guarantee> </user-data-constraint> </security-constraint> <login-config> <!-- Client-side SSL certificate based authentication. The cert is passed to the server to authenticate --> <!-- I am pretty sure that CLIENT-CERT should have a dash NOT an underscore see: http://www.mail-archive.com/[email protected]/msg139845.html --> <!-- CLIENT-CERT uses a client's AND server's certificates. See: http://monduke.com/2006/01/19/the-mysterious-client-cert/ --> <auth-method> CLIENT-CERT </auth-method> </login-config> Update Actually it appears that I have made an error in my original posting. The web.xml does block users from connecting to the webservice using http (port C below). However users are still allowed to connect to ports that do not force users to authenticate themselves (port B). I think that users should be able to connect to port A (it has clientAuth="true") but I dont think that people should be able to connect to port B (it has clientAuth="false"). Excerpt from server.xml <Connector port="<A>" ... SSLEnabled="true" ... scheme="https" secure="true" clientAuth="true" keystoreFile="... .keystore" keystorePass="pword" truststoreFile="... .keystore" truststorePass="pword" sslProtocol="TLS"/> <Connector port="<B>" ... SSLEnabled="true" ... scheme="https" secure="true" clientAuth="false" keystoreFile="... .keystore" keystorePass="pword" sslProtocol = "TLS" /> <Connector port="<C>" ... />

  Read the article

• Unity not Working 14.04

  - by Back.Slash

  I am using Ubuntu 14.04 LTS x64. I did a sudo apt-get upgrade yesterday and restarted my PC. Now my taskbar and panel are missing. When I try to restart Unity using unity --replace Then I get error: unity-panel-service stop/waiting compiz (core) - Info: Loading plugin: core compiz (core) - Info: Starting plugin: core unity-panel-service start/running, process 3906 compiz (core) - Info: Loading plugin: ccp compiz (core) - Info: Starting plugin: ccp compizconfig - Info: Backend : gsettings compizconfig - Info: Integration : true compizconfig - Info: Profile : unity compiz (core) - Info: Loading plugin: composite compiz (core) - Info: Starting plugin: composite compiz (core) - Info: Loading plugin: opengl compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Starting plugin: opengl libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/i965_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/i965_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/i965_dri.so failed (${ORIGIN}/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/i965_dri.so failed (/usr/lib/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: i965_dri.so libGL error: driver pointer missing libGL error: failed to load driver: i965 libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/swrast_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/swrast_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/swrast_dri.so failed (${ORIGIN}/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/swrast_dri.so failed (/usr/lib/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: swrast_dri.so libGL error: failed to load driver: swrast compiz (core) - Info: Loading plugin: compiztoolbox compiz (core) - Info: Starting plugin: compiztoolbox compiz (core) - Info: Loading plugin: decor compiz (core) - Info: Starting plugin: decor compiz (core) - Info: Loading plugin: vpswitch compiz (core) - Info: Starting plugin: vpswitch compiz (core) - Info: Loading plugin: snap compiz (core) - Info: Starting plugin: snap compiz (core) - Info: Loading plugin: mousepoll compiz (core) - Info: Starting plugin: mousepoll compiz (core) - Info: Loading plugin: resize compiz (core) - Info: Starting plugin: resize compiz (core) - Info: Loading plugin: place compiz (core) - Info: Starting plugin: place compiz (core) - Info: Loading plugin: move compiz (core) - Info: Starting plugin: move compiz (core) - Info: Loading plugin: wall compiz (core) - Info: Starting plugin: wall compiz (core) - Info: Loading plugin: grid compiz (core) - Info: Starting plugin: grid compiz (core) - Info: Loading plugin: regex compiz (core) - Info: Starting plugin: regex compiz (core) - Info: Loading plugin: imgpng compiz (core) - Info: Starting plugin: imgpng compiz (core) - Info: Loading plugin: session compiz (core) - Info: Starting plugin: session I/O warning : failed to load external entity "/home/sumeet/.compiz/session/10de541a813cc1a8fc140170575114755000000020350005" compiz (core) - Info: Loading plugin: gnomecompat compiz (core) - Info: Starting plugin: gnomecompat compiz (core) - Info: Loading plugin: animation compiz (core) - Info: Starting plugin: animation compiz (core) - Info: Loading plugin: fade compiz (core) - Info: Starting plugin: fade compiz (core) - Info: Loading plugin: unitymtgrabhandles compiz (core) - Info: Starting plugin: unitymtgrabhandles compiz (core) - Info: Loading plugin: workarounds compiz (core) - Info: Starting plugin: workarounds compiz (core) - Info: Loading plugin: scale compiz (core) - Info: Starting plugin: scale compiz (core) - Info: Loading plugin: expo compiz (core) - Info: Starting plugin: expo compiz (core) - Info: Loading plugin: ezoom compiz (core) - Info: Starting plugin: ezoom compiz (core) - Info: Loading plugin: unityshell compiz (core) - Info: Starting plugin: unityshell WARN 2014-06-02 18:46:23 unity.glib.dbus.server GLibDBusServer.cpp:579 Can't register object 'org.gnome.Shell' yet as we don't have a connection, waiting for it... ERROR 2014-06-02 18:46:23 unity.debug.interface DebugDBusInterface.cpp:216 Unable to load entry point in libxpathselect: libxpathselect.so.1.4: cannot open shared object file: No such file or directory compiz (unityshell) - Error: GL_ARB_vertex_buffer_object not supported ERROR 2014-06-02 18:46:23 unity.shell.compiz unityshell.cpp:3850 Impossible to delete the unity locked stamp file compiz (core) - Error: Plugin initScreen failed: unityshell compiz (core) - Error: Failed to start plugin: unityshell compiz (core) - Info: Unloading plugin: unityshell X Error of failed request: BadWindow (invalid Window parameter) Major opcode of failed request: 3 (X_GetWindowAttributes) Resource id in failed request: 0x3e000c9 Serial number of failed request: 10115 Current serial number in output stream: 10116 Any help would be highly appreciated. EDIT : My PC configuration description: Portable Computer product: Dell System XPS L502X (System SKUNumber) vendor: Dell Inc. version: 0.1 serial: 1006ZP1 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: administrator_password=unknown boot=normal chassis=portable family=HuronRiver System frontpanel_password=unknown keyboard_password=unknown power-on_password=unknown sku=System SKUNumber uuid=44454C4C-3000-1030-8036-B1C04F5A5031 *-core description: Motherboard product: 0YR8NN vendor: Dell Inc. physical id: 0 version: A00 serial: .1006ZP1.CN4864314C0560. slot: Part Component *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A11 date: 05/29/2012 size: 128KiB capacity: 2496KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot smartbattery biosbootspecification netboot *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 19 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: Not Supported by CPU slot: CPU size: 800MHz capacity: 800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts nopl xtopology nonstop_tsc aperfmperf eagerfpu pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=4 threads=8 *-cache:0 description: L1 cache physical id: 1a slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: synchronous internal write-through data *-cache:1 description: L2 cache physical id: 1b slot: L2-Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through data *-cache:2 description: L3 cache physical id: 1c slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: synchronous internal write-back unified *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 6GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: M471B5273DH0-CH9 vendor: Samsung physical id: 0 serial: 450F1160 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 0CA0E8E2 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:3000(size=4096) memory:f0000000-f10fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:f0000000-f0ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:3000(size=128) memory:f1000000-f107ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:52 memory:f1400000-f17fffff memory:e0000000-efffffff ioport:4000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei_me latency=0 resources: irq:50 memory:f1c05000-f1c0500f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:16 memory:f1c09000-f1c093ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:53 memory:f1c00000-f1c03fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode cap_list configuration: driver=pcieport resources: irq:16 *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 memory:f1b00000-f1bfffff *-network description: Wireless interface product: Centrino Wireless-N 1030 [Rainbow Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 34 serial: bc:77:37:14:47:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-27-generic firmware=18.168.6.1 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:f1b00000-f1b01fff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:19 memory:f1a00000-f1afffff *-usb description: USB controller product: uPD720200 USB 3.0 Host Controller vendor: NEC Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:f1a00000-f1a01fff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:f1900000-f19fffff *-pci:5 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 ioport:2000(size=4096) ioport:f1800000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 06 serial: 14:fe:b5:a3:ac:40 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=172.19.167.151 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:49 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:23 memory:f1c08000-f1c083ff *-isa description: ISA bridge product: HM67 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: driver=lpc_ich latency=0 resources: irq:0 *-ide:0 description: IDE interface product: 6 Series/C200 Series Chipset Family 4 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40b8(size=8) ioport:40cc(size=4) ioport:40b0(size=8) ioport:40c8(size=4) ioport:4090(size=16) ioport:4080(size=16) *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:f1c04000-f1c040ff ioport:efa0(size=32) *-ide:1 description: IDE interface product: 6 Series/C200 Series Chipset Family 2 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.5 bus info: pci@0000:00:1f.5 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40a8(size=8) ioport:40c4(size=4) ioport:40a0(size=8) ioport:40c0(size=4) ioport:4070(size=16) ioport:4060(size=16) *-scsi:0 physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: SAMSUNG HN-M640M physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 2AR1 serial: S2T3J1KBC00006 size: 596GiB (640GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=6b746d91 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: 0272-3e7f size: 348MiB capacity: 350MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2013-09-18 12:20:45 filesystem=ntfs label=System Reserved modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 116GiB capacity: 116GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 6037MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 110GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 logical name: /media/os version: 3.1 serial: 4e7853ec-5555-a74d-82e0-9f49798d3772 size: 156GiB capacity: 156GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-19 09:19:00 filesystem=ntfs label=OS mount.fstype=fuseblk mount.options=ro,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/data version: 3.1 serial: 7666d55f-e1bf-e645-9791-2a1a31b24b9a size: 322GiB capacity: 322GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-17 23:27:01 filesystem=ntfs label=Data modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-scsi:1 physical id: 2 logical name: scsi1 capabilities: emulated *-cdrom description: DVD-RAM writer product: DVD+-RW GT32N vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/sr0 version: A201 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-battery product: DELL vendor: SANYO physical id: 1 version: 2008 serial: 1.0 slot: Rear capacity: 57720mWh configuration: voltage=11.1V `

  Read the article

• Why Wifi no longer works 12.04.1

  - by Roger

  starting this morning over wifi (Realtek RTL8188CE) on CLEVO W253HU. May be due to the update before yesterday, more pilot managed, but somehow it worked yesterday. If someone has an idea of the problem. Back command lines: cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 006: ID 192f:0416 Avago Technologies, Pte. Bus 002 Device 004: ID 5986:0315 Acer, Inc lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) lspci -nn | grep -i net 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 03:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) lspci -k 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: i2c-i801 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device 9196 Kernel modules: rtl8192ce 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jme Kernel modules: jme 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: sdhci-pci 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jmb38x_ms Kernel modules: jmb38x_ms sudo lshw -C network *-network NON-RÉCLAMÉ description: Network controller produit: RTL8188CE 802.11b/g/n WiFi Adapter fabriquant: Realtek Semiconductor Co., Ltd. identifiant matériel: 0 information bus: pci@0000:02:00.0 version: 01 bits: 64 bits horloge: 33MHz fonctionnalités: pm msi pciexpress cap_list configuration: latency=0 ressources: portE/S:e000(taille=256) mémoire:f7d00000-f7d03fff *-network description: Ethernet interface produit: JMC250 PCI Express Gigabit Ethernet Controller fabriquant: JMicron Technology Corp. identifiant matériel: 0 information bus: pci@0000:03:00.0 nom logique: eth0 version: 05 numéro de série: 00:90:f5:c1:c6:45 taille: 100Mbit/s capacité: 1Gbit/s bits: 32 bits horloge: 33MHz fonctionnalités: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=full ip=192.168.1.54 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s ressources: irq:44 mémoire:f7c20000-f7c23fff portE/S:d100(taille=128) portE/S:d000(taille=256) mémoire:f7c10000-f7c1ffff mémoire:f7c00000-f7c0ffff lsmod Module Size Used by btusb 18288 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 11 btusb,rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 binfmt_misc 17540 1 snd_hda_codec_realtek 224173 0 dm_crypt 23125 0 snd_hda_codec_hdmi 32474 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev snd_hda_intel 33773 2 snd_hda_codec 127706 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi jmb38x_ms 17646 0 psmouse 87692 0 serio_raw 13211 0 memstick 16569 1 jmb38x_ms snd_seq_midi_event 14899 1 snd_seq_midi rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi mac_hid 13253 0 snd 78855 14 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 205544 2 rtlwifi,mac80211 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid i915 473035 3 drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper jme 41259 0 i2c_algo_bit 13423 1 i915 sdhci_pci 18826 0 sdhci 33205 1 sdhci_pci wmi 19256 0 video 19596 1 i915 iwconfig lo no wireless extensions. eth0 no wireless extensions. ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:c1:c6:45 inet adr:192.168.1.54 Bcast:192.168.1.255 Masque:255.255.255.0 adr inet6: fe80::290:f5ff:fec1:c645/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:4513 erreurs:0 :0 overruns:0 frame:0 TX packets:4359 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:3471675 (3.4 MB) Octets transmis:712722 (712.7 KB) Interruption:44 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:686 erreurs:0 :0 overruns:0 frame:0 TX packets:686 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 Octets reçus:64556 (64.5 KB) Octets transmis:64556 (64.5 KB) sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. uname -r -m 3.2.0-30-generic x86_64 cat /etc/network/interfaces auto lo iface lo inet loopback nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Connexion filaire 1] ------------------------------------------ Type: Wired Driver: jme State: connected Default: yes HW Address: 00:90:F5:C1:C6:45 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.54 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 sudo rfkill listrfkill list 1: hci0: Bluetooth Soft blocked: no Hard blocked: no The absence of line "Kernel driver in use:" the return of lspci-k made ??me think that it is not loaded yet but he seems to be. lsmod | grep rtl8192ce rtl8192ce 137478 0 rtlwifi 118749 1 rtl8192ce mac80211 506816 2 rtl8192ce,rtlwifi I found something disturbing in / var / log / syslog Sep 14 11:40:11 pcroger kernel: [ 64.048783] rtl8192ce-0:rtl92c_init_sw_vars():<0-0> Failed to request firmware! Sep 14 11:40:11 pcroger kernel: [ 64.048795] rtlwifi-0:rtl_pci_probe():<0-0> Can't init_sw_vars. Sep 14 11:40:11 pcroger kernel: [ 64.048835] rtl8192ce 0000:02:00.0: PCI INT A disabled Sep 14 11:40:11 pcroger kernel: [ 64.943345] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6 frozen Sep 14 11:40:11 pcroger kernel: [ 64.943358] ata1.00: failed command: READ FPDMA QUEUED Sep 14 11:40:11 pcroger kernel: [ 64.943371] ata1.00: cmd 60/00:00:00:68:6a/04:00:0b:00:00/40 tag 0 ncq 524288 in Sep 14 11:40:11 pcroger kernel: [ 64.943374] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) Sep 14 11:40:11 pcroger kernel: [ 64.943381] ata1.00: status: { DRDY } Ubuntu and takes forever to start (2 min).

  Read the article

• Oracle Linux Tips and Tricks: Using SSH

  - by Robert Chase

  Out of all of the utilities available to systems administrators ssh is probably the most useful of them all. Not only does it allow you to log into systems securely, but it can also be used to copy files, tunnel IP traffic and run remote commands on distant servers. It’s truly the Swiss army knife of systems administration. Secure Shell, also known as ssh, was developed in 1995 by Tau Ylonen after the University of Technology in Finland suffered a password sniffing attack. Back then it was common to use tools like rcp, rsh, ftp and telnet to connect to systems and move files across the network. The main problem with these tools is they provide no security and transmitted data in plain text including sensitive login credentials. SSH provides this security by encrypting all traffic transmitted over the wire to protect from password sniffing attacks. One of the more common use cases involving SSH is found when using scp. Secure Copy (scp) transmits data between hosts using SSH and allows you to easily copy all types of files. The syntax for the scp command is: scp /pathlocal/filenamelocal remoteuser@remotehost:/pathremote/filenameremote In the following simple example, I move a file named myfile from the system test1 to the system test2. I am prompted to provide valid user credentials for the remote host before the transfer will proceed.  If I were only using ftp, this information would be unencrypted as it went across the wire.  However, because scp uses SSH, my user credentials and the file and its contents are confidential and remain secure throughout the transfer.  [user1@test1 ~]# scp /home/user1/myfile user1@test2:/home/user1user1@test2's password: myfile                                    100%    0     0.0KB/s   00:00 You can also use ssh to send network traffic and utilize the encryption built into ssh to protect traffic over the wire. This is known as an ssh tunnel. In order to utilize this feature, the server that you intend to connect to (the remote system) must have TCP forwarding enabled within the sshd configuraton. To enable TCP forwarding on the remote system, make sure AllowTCPForwarding is set to yes and enabled in the /etc/ssh/sshd_conf file: AllowTcpForwarding yes Once you have this configured, you can connect to the server and setup a local port which you can direct traffic to that will go over the secure tunnel. The following command will setup a tunnel on port 8989 on your local system. You can then redirect a web browser to use this local port, allowing the traffic to go through the encrypted tunnel to the remote system. It is important to select a local port that is not being used by a service and is not restricted by firewall rules.  In the following example the -D specifies a local dynamic application level port forwarding and the -N specifies not to execute a remote command.   ssh –D 8989 [email protected] -N You can also forward specific ports on both the local and remote host. The following example will setup a port forward on port 8080 and forward it to port 80 on the remote machine. ssh -L 8080:farwebserver.com:80 [email protected] You can even run remote commands via ssh which is quite useful for scripting or remote system administration tasks. The following example shows how to  log in remotely and execute the command ls –la in the home directory of the machine. Because ssh encrypts the traffic, the login credentials and output of the command are completely protected while they travel over the wire. [rchase@test1 ~]$ ssh rchase@test2 'ls -la'rchase@test2's password: total 24drwx------  2 rchase rchase 4096 Sep  6 15:17 .drwxr-xr-x. 3 root   root   4096 Sep  6 15:16 ..-rw-------  1 rchase rchase   12 Sep  6 15:17 .bash_history-rw-r--r--  1 rchase rchase   18 Dec 20  2012 .bash_logout-rw-r--r--  1 rchase rchase  176 Dec 20  2012 .bash_profile-rw-r--r--  1 rchase rchase  124 Dec 20  2012 .bashrc You can execute any command contained in the quotations marks as long as you have permission with the user account that you are using to log in. This can be very powerful and useful for collecting information for reports, remote controlling systems and performing systems administration tasks using shell scripts. To make your shell scripts even more useful and to automate logins you can use ssh keys for running commands remotely and securely without the need to enter a password. You can accomplish this with key based authentication. The first step in setting up key based authentication is to generate a public key for the system that you wish to log in from. In the following example you are generating a ssh key on a test system. In case you are wondering, this key was generated on a test VM that was destroyed after this article. [rchase@test1 .ssh]$ ssh-keygen -t rsaGenerating public/private rsa key pair.Enter file in which to save the key (/home/rchase/.ssh/id_rsa): Enter passphrase (empty for no passphrase): Enter same passphrase again: Your identification has been saved in /home/rchase/.ssh/id_rsa.Your public key has been saved in /home/rchase/.ssh/id_rsa.pub.The key fingerprint is:7a:8e:86:ef:59:70:ef:43:b7:ee:33:03:6e:6f:69:e8 rchase@test1The key's randomart image is:+--[ RSA 2048]----+|                 ||  . .            ||   o .           ||    . o o        ||   o o oS+       ||  +   o.= =      ||   o ..o.+ =     ||    . .+. =      ||     ...Eo       |+-----------------+ Now that you have the key generated on the local system you should to copy it to the target server into a temporary location. The user’s home directory is fine for this. [rchase@test1 .ssh]$ scp id_rsa.pub rchase@test2:/home/rchaserchase@test2's password: id_rsa.pub                  Now that the file has been copied to the server, you need to append it to the authorized_keys file. This should be appended to the end of the file in the event that there are other authorized keys on the system. [rchase@test2 ~]$ cat id_rsa.pub >> .ssh/authorized_keys Once the process is complete you are ready to login. Since you are using key based authentication you are not prompted for a password when logging into the system.   [rchase@test1 ~]$ ssh test2Last login: Fri Sep  6 17:42:02 2013 from test1 This makes it much easier to run remote commands. Here’s an example of the remote command from earlier. With no password it’s almost as if the command ran locally. [rchase@test1 ~]$ ssh test2 'ls -la'total 32drwx------  3 rchase rchase 4096 Sep  6 17:40 .drwxr-xr-x. 3 root   root   4096 Sep  6 15:16 ..-rw-------  1 rchase rchase   12 Sep  6 15:17 .bash_history-rw-r--r--  1 rchase rchase   18 Dec 20  2012 .bash_logout-rw-r--r--  1 rchase rchase  176 Dec 20  2012 .bash_profile-rw-r--r--  1 rchase rchase  124 Dec 20  2012 .bashrc As a security consideration it's important to note the permissions of .ssh and the authorized_keys file.  .ssh should be 700 and authorized_keys should be set to 600.  This prevents unauthorized access to ssh keys from other users on the system.   An even easier way to move keys back and forth is to use ssh-copy-id. Instead of copying the file and appending it manually to the authorized_keys file, ssh-copy-id does both steps at once for you.  Here’s an example of moving the same key using ssh-copy-id.The –i in the example is so that we can specify the path to the id file, which in this case is /home/rchase/.ssh/id_rsa.pub [rchase@test1]$ ssh-copy-id -i /home/rchase/.ssh/id_rsa.pub rchase@test2 One of the last tips that I will cover is the ssh config file. By using the ssh config file you can setup host aliases to make logins to hosts with odd ports or long hostnames much easier and simpler to remember. Here’s an example entry in our .ssh/config file. Host dev1 Hostname somereallylonghostname.somereallylongdomain.com Port 28372 User somereallylongusername12345678 Let’s compare the login process between the two. Which would you want to type and remember? ssh somereallylongusername12345678@ somereallylonghostname.somereallylongdomain.com –p 28372 ssh dev1 I hope you find these tips useful.  There are a number of tools used by system administrators to streamline processes and simplify workflows and whether you are new to Linux or a longtime user, I'm sure you will agree that SSH offers useful features that can be used every day.  Send me your comments and let us know the ways you  use SSH with Linux.  If you have other tools you would like to see covered in a similar post, send in your suggestions.

  Read the article

• Wifi hotspot disconnected after some time

  - by Rohit Bansal

  I am trying to use my Ubuntu system as Wifi Hotspot, but for some reason Hotspot get disconnected on its own. Searching for the solution, I found this help : Why is my ethernet connection connecting and disconnecting repeatedly? Reading through the above article I used the following command sudo killall dnsmasq as a result I manage to establish hotspot for around 5-10 sec before getting disconnected as against immediately.... Here's the system log (in case needed) tail -f /var/log/syslog : Apr 1 23:31:42 NetworkManager[901]: <info> Starting dnsmasq... Apr 1 23:31:42 NetworkManager[901]: <info> (wlan0): device state change: ip-config -> activated (reason 'none') [70 100 0] Apr 1 23:31:42 dnsmasq[4159]: started, version 2.57 cachesize 150 Apr 1 23:31:42 dnsmasq[4159]: compile time options: IPv6 GNU-getopt DBus I18N DHCP TFTP IDN Apr 1 23:31:42 dnsmasq-dhcp[4159]: DHCP, IP range 10.42.43.10 -- 10.42.43.100, lease time 1h Apr 1 23:31:42 dnsmasq[4159]: reading /etc/resolv.conf Apr 1 23:31:42 dnsmasq[4159]: using nameserver 220.226.6.104#53 Apr 1 23:31:42 dnsmasq[4159]: using nameserver 220.226.100.40#53 Apr 1 23:31:42 dnsmasq[4159]: cleared cache Apr 1 23:31:42 NetworkManager[901]: <info> Activation (wlan0) successful, device activated. Apr 1 23:31:42 NetworkManager[901]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) complete. Apr 1 23:31:42 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) complete. Apr 1 23:31:42 dbus[885]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Apr 1 23:31:42 dbus[885]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Connection established at this point....now disconnecting after 10 sec... Apr 1 23:31:52 ntpdate[4194]: adjust time server 91.189.94.4 offset -0.011589 sec Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): IP6 addrconf timed out or failed. Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) scheduled... Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) started... Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) started... Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --out-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --out-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --source 10.42.43.0/255.255.255.0 --in-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --destination 10.42.43.0/255.255.255.0 --out-interface wlan0 --match state --state ESTABLISHED,RELATED --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table nat --insert POSTROUTING --source 10.42.43.0/255.255.255.0 ! --destination 10.42.43.0/255.255.255.0 --jump MASQUERADE Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --out-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --out-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --source 10.42.43.0/255.255.255.0 --in-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --destination 10.42.43.0/255.255.255.0 --out-interface wlan0 --match state --state ESTABLISHED,RELATED --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table nat --insert POSTROUTING --source 10.42.43.0/255.255.255.0 ! --destination 10.42.43.0/255.255.255.0 --jump MASQUERADE Apr 1 23:32:01 NetworkManager[901]: <info> Starting dnsmasq... Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) complete. Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) complete. Apr 1 23:32:01 NetworkManager[901]: <warn> dnsmasq died with signal 9 Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): device state change: activated -> failed (reason 'sharing-start-failed') [100 120 18] Apr 1 23:32:01 dnsmasq[4235]: started, version 2.57 cachesize 150 Apr 1 23:32:01 dnsmasq[4235]: compile time options: IPv6 GNU-getopt DBus I18N DHCP TFTP IDN Apr 1 23:32:01 dnsmasq-dhcp[4235]: DHCP, IP range 10.42.43.10 -- 10.42.43.100, lease time 1h Apr 1 23:32:01 NetworkManager[901]: <warn> Activation (wlan0) failed for access point (Reppify Ubuntu) Apr 1 23:32:01 dnsmasq[4235]: reading /etc/resolv.conf Apr 1 23:32:01 dnsmasq[4235]: using nameserver 220.226.6.104#53 Apr 1 23:32:01 dnsmasq[4235]: using nameserver 220.226.100.40#53 Apr 1 23:32:01 dnsmasq[4235]: cleared cache Apr 1 23:32:01 NetworkManager[901]: <warn> Activation (wlan0) failed. Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): deactivating device (reason 'none') [0] Apr 1 23:32:01 dbus[885]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Apr 1 23:32:01 dbus[885]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Apr 1 23:32:01 NetworkManager[901]: <error> [1333303321.565351] [nm-device-wifi.c:1815] nm_device_wifi_set_mode(): (wlan0): error setting mode 2

  Read the article

• Question regarding filesystems true or false?

  - by Avon

  Hello all, though I'm familiar with stackoverflow , and loving it , i've actually got a couple of questions myself about something other then programming. Here are my question Is it true that in FAT filesystems the maximum number of files per filesystem equals the number of entries in the FAT table. And is it also true that in indexed filesystems the maximum number of files per filesystem equals the number of indexblocks – 1. I'm reading some stuff and am trying to get a good understanding of it.

  Read the article

• Excel inventory spreadsheet

  - by user24142

  Hi, I need to know the best way to set up a spreadsheet which has product information (i.e name cost, sale price, number purchased, number sold, number left in stock) Every week I check the stock so need to be able to to enter the new current value of the number left in stock. The every week I buy new stock. Sometimes the stock changes in price. The spreadsheet needs to also keep track of how much money I should have from the sales of the stock and then therefore the profit made etc. Thanks

  Read the article

• Adaptec 5805 after reboot don't starting

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

  Read the article

• Shell Script if else

  - by user34104

  #!/bin/bash echo "Int. a number" read num1 echo "Int. another numer" read num2 if ["$num1"="$num2"]; then echo "Equals" else echo "Dif" fi if["$num1"<0]; then echo "The number $num1 is negative" else if ["$num2"<0]; then echo "The number $num2 is negative" fi # this code is not working, i've something wrong when i see if the number is < 0. thanks

  Read the article

• How can I replace email alerts for system events with something more scalable?

  - by Dave Forgac

  I have a number of systems and services that send email alerts when some sort of event takes place. This works fine for a small number of systems but as the number of alerts grows the important message become less visible among the informational notices. Email filtering can only be effective to a point. What sort of solution can I use in place of emails that will allow me to send arbitrary alerts from various services and that will scale easily as the number of services grows?

  Read the article

• Strange Recurrent Excessive I/O Wait

  - by Chris

  I know quite well that I/O wait has been discussed multiple times on this site, but all the other topics seem to cover constant I/O latency, while the I/O problem we need to solve on our server occurs at irregular (short) intervals, but is ever-present with massive spikes of up to 20k ms a-wait and service times of 2 seconds. The disk affected is /dev/sdb (Seagate Barracuda, for details see below). A typical iostat -x output would at times look like this, which is an extreme sample but by no means rare: iostat (Oct 6, 2013) tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16.00 0.00 156.00 9.75 21.89 288.12 36.00 57.60 5.50 0.00 44.00 8.00 48.79 2194.18 181.82 100.00 2.00 0.00 16.00 8.00 46.49 3397.00 500.00 100.00 4.50 0.00 40.00 8.89 43.73 5581.78 222.22 100.00 14.50 0.00 148.00 10.21 13.76 5909.24 68.97 100.00 1.50 0.00 12.00 8.00 8.57 7150.67 666.67 100.00 0.50 0.00 4.00 8.00 6.31 10168.00 2000.00 100.00 2.00 0.00 16.00 8.00 5.27 11001.00 500.00 100.00 0.50 0.00 4.00 8.00 2.96 17080.00 2000.00 100.00 34.00 0.00 1324.00 9.88 1.32 137.84 4.45 59.60 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 22.00 44.00 204.00 11.27 0.01 0.27 0.27 0.60 Let me provide you with some more information regarding the hardware. It's a Dell 1950 III box with Debian as OS where uname -a reports the following: Linux xx 2.6.32-5-amd64 #1 SMP Fri Feb 15 15:39:52 UTC 2013 x86_64 GNU/Linux The machine is a dedicated server that hosts an online game without any databases or I/O heavy applications running. The core application consumes about 0.8 of the 8 GBytes RAM, and the average CPU load is relatively low. The game itself, however, reacts rather sensitive towards I/O latency and thus our players experience massive ingame lag, which we would like to address as soon as possible. iostat: avg-cpu: %user %nice %system %iowait %steal %idle 1.77 0.01 1.05 1.59 0.00 95.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sdb 13.16 25.42 135.12 504701011 2682640656 sda 1.52 0.74 20.63 14644533 409684488 Uptime is: 19:26:26 up 229 days, 17:26, 4 users, load average: 0.36, 0.37, 0.32 Harddisk controller: 01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04) Harddisks: Array 1, RAID-1, 2x Seagate Cheetah 15K.5 73 GB SAS Array 2, RAID-1, 2x Seagate ST3500620SS Barracuda ES.2 500GB 16MB 7200RPM SAS Partition information from df: Filesystem 1K-blocks Used Available Use% Mounted on /dev/sdb1 480191156 30715200 425083668 7% /home /dev/sda2 7692908 437436 6864692 6% / /dev/sda5 15377820 1398916 13197748 10% /usr /dev/sda6 39159724 19158340 18012140 52% /var Some more data samples generated with iostat -dx sdb 1 (Oct 11, 2013) Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sdb 0.00 15.00 0.00 70.00 0.00 656.00 9.37 4.50 1.83 4.80 33.60 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 12.00 836.00 500.00 100.00 sdb 0.00 0.00 0.00 3.00 0.00 32.00 10.67 9.96 1990.67 333.33 100.00 sdb 0.00 0.00 0.00 4.00 0.00 40.00 10.00 6.96 3075.00 250.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 4.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 2.62 4648.00 500.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 2.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 1.00 0.00 16.00 16.00 1.69 7024.00 1000.00 100.00 sdb 0.00 74.00 0.00 124.00 0.00 1584.00 12.77 1.09 67.94 6.94 86.00 Characteristic charts generated with rrdtool can be found here: iostat plot 1, 24 min interval: http://imageshack.us/photo/my-images/600/yqm3.png/ iostat plot 2, 120 min interval: http://imageshack.us/photo/my-images/407/griw.png/ As we have a rather large cache of 5.5 GBytes, we thought it might be a good idea to test if the I/O wait spikes would perhaps be caused by cache miss events. Therefore, we did a sync and then this to flush the cache and buffers: echo 3 > /proc/sys/vm/drop_caches and directly afterwards the I/O wait and service times virtually went through the roof, and everything on the machine felt like slow motion. During the next few hours the latency recovered and everything was as before - small to medium lags in short, unpredictable intervals. Now my question is: does anybody have any idea what might cause this annoying behaviour? Is it the first indication of the disk array or the raid controller dying, or something that can be easily mended by rebooting? (At the moment we're very reluctant to do this, however, because we're afraid that the disks might not come back up again.) Any help is greatly appreciated. Thanks in advance, Chris. Edited to add: we do see one or two processes go to 'D' state in top, one of which seems to be kjournald rather frequently. If I'm not mistaken, however, this does not indicate the processes causing the latency, but rather those affected by it - correct me if I'm wrong. Does the information about uninterruptibly sleeping processes help us in any way to address the problem? @Andy Shinn requested smartctl data, here it is: smartctl -a -d megaraid,2 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:13 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 20 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 1236631092 Blocks received from initiator = 1097862364 Blocks read from cache and sent to initiator = 1383620256 Number of read and write commands whose size <= segment size = 531295338 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36556.93 number of minutes until next internal SMART test = 32 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 509271032 47 0 509271079 509271079 20981.423 0 write: 0 0 0 0 0 5022.039 0 verify: 1870931090 196 0 1870931286 1870931286 100558.708 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36538 - [- - -] # 2 Background short Completed 16 36514 - [- - -] # 3 Background short Completed 16 36490 - [- - -] # 4 Background short Completed 16 36466 - [- - -] # 5 Background short Completed 16 36442 - [- - -] # 6 Background long Completed 16 36420 - [- - -] # 7 Background short Completed 16 36394 - [- - -] # 8 Background short Completed 16 36370 - [- - -] # 9 Background long Completed 16 36364 - [- - -] #10 Background short Completed 16 36361 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes] smartctl -a -d megaraid,3 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:26 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 19 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 288745640 Blocks received from initiator = 1097848399 Blocks read from cache and sent to initiator = 1304149705 Number of read and write commands whose size <= segment size = 527414694 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36596.83 number of minutes until next internal SMART test = 28 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 610862490 44 0 610862534 610862534 20470.133 0 write: 0 0 0 0 0 5022.480 0 verify: 2861227413 203 0 2861227616 2861227616 100872.443 0 Non-medium error count: 1 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36580 - [- - -] # 2 Background short Completed 16 36556 - [- - -] # 3 Background short Completed 16 36532 - [- - -] # 4 Background short Completed 16 36508 - [- - -] # 5 Background short Completed 16 36484 - [- - -] # 6 Background long Completed 16 36462 - [- - -] # 7 Background short Completed 16 36436 - [- - -] # 8 Background short Completed 16 36412 - [- - -] # 9 Background long Completed 16 36404 - [- - -] #10 Background short Completed 16 36401 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes]

  Read the article

• nginx reverse proxy cannot access apache virtual hosts

  - by Sc0rian

  I am setting up nginx as a reverse proxy. The server runs on directadmin and lamp stack. I have nginx running on port 81. I can access all my sites (including virtual ips) on the port 81. However when I forward the traffic from port 80 to 81, the virtual ips have a message saying "Apache is running normally". Server IPs are fine, and I can still access virtual IP's on 81. [root@~]# netstat -an | grep LISTEN | egrep ":80|:81" tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <serverip>:81 0.0.0.0:* LISTEN tcp 0 0 :::80 :::* LISTEN apache 24090 0.6 1.3 29252 13612 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24092 0.9 2.1 39584 22056 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24096 0.2 1.9 35892 20256 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24120 0.3 1.7 35752 17840 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24495 0.0 1.4 30892 14756 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24496 1.0 2.1 39892 22164 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24516 1.5 3.6 55496 38040 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24519 0.1 1.2 28996 13224 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24521 2.7 4.0 58244 41984 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24522 0.0 1.2 29124 12672 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24524 0.0 1.1 28740 12364 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24535 1.1 1.7 36008 17876 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24536 0.0 1.1 28592 12084 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24537 0.0 1.1 28592 12112 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24539 0.0 0.0 0 0 ? Z 18:35 0:00 [httpd] <defunct> apache 24540 0.0 1.1 28592 11540 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24541 0.0 1.1 28592 11548 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL root 24548 0.0 0.0 4132 752 pts/0 R+ 18:35 0:00 egrep apache|nginx root 28238 0.0 0.0 19576 284 ? Ss May29 0:00 nginx: master process /usr/local/nginx/sbin/nginx -c /usr/local/nginx/conf/nginx.conf apache 28239 0.0 0.0 19888 804 ? S May29 0:00 nginx: worker process apache 28240 0.0 0.0 19888 548 ? S May29 0:00 nginx: worker process apache 28241 0.0 0.0 19736 484 ? S May29 0:00 nginx: cache manager process here is my nginx conf: cat /usr/local/nginx/conf/nginx.conf user apache apache; worker_processes 2; # Set it according to what your CPU have. 4 Cores = 4 worker_rlimit_nofile 8192; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] ' '"$request" $status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; server_tokens off; access_log /var/log/nginx_access.log main; error_log /var/log/nginx_error.log debug; server_names_hash_bucket_size 64; sendfile on; tcp_nopush on; tcp_nodelay off; keepalive_timeout 30; gzip on; gzip_comp_level 9; gzip_proxied any; proxy_buffering on; proxy_cache_path /usr/local/nginx/proxy_temp levels=1:2 keys_zone=one:15m inactive=7d max_size=1000m; proxy_buffer_size 16k; proxy_buffers 100 8k; proxy_connect_timeout 60; proxy_send_timeout 60; proxy_read_timeout 60; server { listen <server ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <server host name> _; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<server ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } location /nginx_status { stub_status on; access_log off; allow 127.0.0.1; deny all; } } include /usr/local/nginx/vhosts/*.conf; } here is my vhost conf: # cat /usr/local/nginx/vhosts/1.conf server { listen <virt ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <virt domain name>.com ; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<virt ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } } Apache config: <VirtualHost xxxxxx:80 > ServerName www.<domain>.com ServerAlias www.<domain>.com <domain>.com ServerAdmin webmaster@<domain>.com DocumentRoot /home/<domain>/domains/<domain>.com/public_html ScriptAlias /cgi-bin/ /home/<domain>/domains/<domain>.com/public_html/cgi-bin/ UseCanonicalName OFF <IfModule !mod_ruid2.c> SuexecUserGroup <domain> <domain> </IfModule> <IfModule mod_ruid2.c> RMode config RUidGid <domain> <domain> RGroups apache access </IfModule> CustomLog /var/log/httpd/domains/<domain>.com.bytes bytes CustomLog /var/log/httpd/domains/<domain>.com.log combined ErrorLog /var/log/httpd/domains/<domain>.com.error.log <Directory /home/<domain>/domains/<domain>.com/public_html> Options +Includes -Indexes php_admin_flag engine ON php_admin_value sendmail_path '/usr/sbin/sendmail -t -i -f <domain>@<domain>.com' </Directory> <virtual ip address>:80 is a NameVirtualHost default server www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:16) port 80 namevhost www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:16) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/xx/httpd.conf:107) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/xx/httpd.conf:151) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/xx/httpd.conf:195) <virtual ip address>:443 is a NameVirtualHost default server www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:61) port 443 namevhost www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:61) <server ip>:80 is a NameVirtualHost default server localhost (/etc/httpd/conf/extra/httpd-vhosts.conf:29) port 80 namevhost localhost (/etc/httpd/conf/extra/httpd-vhosts.conf:29) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/admin/httpd.conf:16)

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• Sql-server-2008 client Access license

  - by thushya

  Hi, case 1 : i have one user makes 10 connection from single computer, maximum number of connection at a given time = 10, what is the number CAL i need here ? case 2 : i have 10 users have access to only 1 computer, 10 user connect from single computer - maximum connection at any given time = 1, what is the number CAL i need here ? case 3 : i have 10 users using 10 computers, all 10 are making total of 5 connection maximum in any given time, what is the number of CAL i need here ? Thanks.

  Read the article

• ql-server-2008 client Access license

  - by thushya

  Hi, case 1 : i have one user makes 10 connection from single computer, maximum number of connection at a given time = 10, what is the number CAL i need here ? case 2 : i have 10 users have access to only 1 computer, 10 user connect from single computer - maximum connection at any given time = 1, what is the number CAL i need here ? case 3 : i have 10 users using 10 computers, all 10 are making total of 5 connection maximum in any given time, what is the number of CAL i need here ? Thanks.

  Read the article

• Mapping JSON data in JQGrid

  - by hunt

  Hi , I am using jqGrid 3.6.4 and a jquery 1.4.2 . in my sample i am getting following json data format & i want to map these json data into rows of a jqgrid { "page": "1", "total": 1, "records": "6", "rows": [ { "head": { "student_name": "Mr S. Jack ", "year": 2007 }, "sub": [ { "course_description": "Math ", "date": "22-04-2010", "number": 1, "time_of_add": "2:00", "day": "today" } ] } ] } my jqgrid code is as follows jQuery("#"+subgrid_table_id).jqGrid({ url:"http://localhost/stud/beta/web/GetStud.php?sid="+sid, dtatype: "json", colNames: ['Stud Name','Year','Date'.'Number'], colModel: [ {name:'Stud Name',index:'student_name', width:100, jsonmap:"student_name"}, {name:'Year',index:'year', width:100, jsonmap:"year"}, {name:'Date',index:'date', width:100, jsonmap:"date"}, {name:'Number',index:'number', width:100, jsonmap:"number"} ], height:'100%', jsonReader: { repeatitems : false, root:"head" }, }); So now the problem is as my data i.e. student_name and year is under "head" , the jqgrid is enable to locate these two fields. at the same time other two column values i.e. Date and Number lies under "sub" and even those columns i am not be able to map it with jqgrid so kindly help me how to located these attributes in JQGrid. Thanks

  Read the article

• parsing a list and producing a structure of that

  - by qzar

  ;; structure representing homework points ;; nr: number - the number of the homework ;; points: number - the number of points reached (define-struct homework (nr points)) ;; parse-homework: (list of number pairs) -> (list of homework) ;; The procedure takes a list of number pairs and produces a list of homework structures ;; Example: (parse-homework (list (list 1 6) (list 2 7) (list 3 0))) should produce (list (make-homework 1 6) (make-homework 2 7) (make-homework 3 0)) (define (parse-homework homework-entries) (if (and (= (length (first homework-entries) 2))(= (length (parse-homework (rest homework-entries)) 2))) (make-homework (first homework-entries) (parse-homework (rest homework-entries))) (error 'Non-valid-input "entered list is not of length two")) ) (parse-homework (list (list 1 6) (list 2 7) (list 3 0))) This code produces the error length: expects 1 argument, given 2: (list 1 6) 2 I really appreciate every explanation that you can give me to get in in this scheme-stuff... Thank you very much

  Read the article

• How to send mail from ASP.NET with IIS6 SMTP in a dedicated server?

  - by Julio César

  Hi. I'm trying to configure a dedicated server that runs ASP.NET to send mail through the local IIS SMTP server but mail is getting stuck in the Queue folder and doesn't get delivered. I'm using this code in an .aspx page to test: <%@ Page Language="C#" AutoEventWireup="true" %> <% new System.Net.Mail.SmtpClient("localhost").Send("[email protected]", "[email protected]", "testing...", "Hello, world.com"); %> Then, I added the following to the Web.config file: <system.net> <mailSettings> <smtp> <network host="localhost"/> </smtp> </mailSettings> </system.net> In the IIS Manager I've changed the following in the properties of the "Default SMTP Virtual Server". General: [X] Enable Logging Access / Authentication: [X] Windows Integrated Authentication Access / Relay Restrictions: (o) Only the list below, Granted 127.0.0.1 Delivery / Advanced: Fully qualified domain name = thedomain.com Finally, I run the SMTPDiag.exe tool like this: C:\>smtpdiag.exe [email protected] [email protected] Searching for Exchange external DNS settings. Computer name is THEDOMAIN. Failed to connect to the domain controller. Error: 8007054b Checking SOA for gmail.com. Checking external DNS servers. Checking internal DNS servers. SOA serial number match: Passed. Checking local domain records. Checking MX records using TCP: thedomain.com. Checking MX records using UDP: thedomain.com. Both TCP and UDP queries succeeded. Local DNS test passed. Checking remote domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Remote DNS test passed. Checking MX servers listed for [email protected]. Connecting to gmail-smtp-in.l.google.com [209.85.199.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to gmail-smtp-in.l.google.com. Connecting to gmail-smtp-in.l.google.com [209.85.199.114] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to gmail-smtp-in.l.google.com. Connecting to alt2.gmail-smtp-in.l.google.com [209.85.135.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to alt2.gmail-smtp-in.l.google.com. Connecting to alt2.gmail-smtp-in.l.google.com [209.85.135.114] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to alt2.gmail-smtp-in.l.google.com. Connecting to alt1.gmail-smtp-in.l.google.com [209.85.133.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to alt1.gmail-smtp-in.l.google.com. Connecting to alt2.gmail-smtp-in.l.google.com [74.125.79.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to alt2.gmail-smtp-in.l.google.com. Connecting to alt2.gmail-smtp-in.l.google.com [74.125.79.114] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to alt2.gmail-smtp-in.l.google.com. Connecting to alt1.gmail-smtp-in.l.google.com [209.85.133.114] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to alt1.gmail-smtp-in.l.google.com. Connecting to gsmtp183.google.com [64.233.183.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to gsmtp183.google.com. Connecting to gsmtp147.google.com [209.85.147.27] on port 25. Connecting to the server failed. Error: 10051 Failed to submit mail to gsmtp147.google.com. I'm using ASP.NET 2.0, Windows 2003 Server and the IIS that comes with it. Can you tell me what else to change to fix the problem? Thanks @mattlant This is a dedicated server that's why I'm installing the SMTP manually. EDIT: I use exchange so its a little different, but its called a smart host in exchange, but in plain SMTP service config i think its called something else. Cant remember exactly the setting name. Thank you for pointing me at the Smart host field. Mail is getting delivered now. In the Default SMTP Virtual Server properties, the Delivery tab, click Advanced and fill the "Smart host" field with the address that your provider gives you. In my case (GoDaddy) it was k2smtpout.secureserver.net. More info here: http://help.godaddy.com/article/1283

  Read the article

• Math algorithm question

  - by Senica Gonzalez

  I'm not sure if this can be done without some determining factor....but wanted to see if someone knew of a way to do this. I want to create a shifting scale for numbers. Let's say I have the number 26000. I want the outcome of this algorithm to be 6500; or 25% of the original number. But if I have the number 5000, I want the outcome to be 2500; or 50% of the original number. The percentages don't have to be exact, this is just an example. I just want to have like a sine wave sort of thing. As the input number gets higher, the output number is a lower percentage of the input. Does that make sense?

  Read the article

• PHP: why uniqid returned value is only 13 digits long

  - by Marco Demaio

  uniqid() function returns a 13 digits long hexadecimal number. According to the spec in php.net site, the function uses microtime to generate the unique value. But microtime returns numbers in string format as the following one: "0.70352700 12689396875" which are basically the microseconds and the seconds elapsed since 1970. This is a 9+11 digits decimal number. Converting a 20 decimal number into hex would result in a 16 digits hexadecimal NOT a 13 digits one. I also thought to take out the "0." part that seem to never change, and the last two digits of the microsec part that seem to remain always "00". Doing this the decimal number would be only 9+11-3 digits long, but still a decimal number of 17 digits when converted into hex would result in 14 digits hexadecimal number NOT 13. You probably think I'm crazy in asking such a thing, but I'm concerned about using uniqid, unique values are important to be unique, a duplicated value could screw up an entire application.

  Read the article

• Reading an XML File with .NET

  - by Daywalker21

  I am new to xml and unable to find a way to get content in between tags. My XML file is <?xml version="1.0" encoding="utf-8"?> <block1> <file name="c:\w0.xml"> <word>Text</word> <number>67</number> </file> <file name="c:\w1.xml"> <word>Text</word> <number>67</number> </file> <file name="c:\w2.xml"> <word>Text</word> <number>67</number> </file> </block1>

  Read the article

• Concatenation with Zero is not occurring properly in code?

  - by Vineet

  I was trying to reverse a number in PL/SQL. It's working fine, but when my number contains any 0, the output is unexpected. For example: 1234 output 4321 1000 output 1 1203 ouput 3021 10001 output 1 DECLARE r number(9); num number(9):=&p_num; BEGIN WHILE num>=1 LOOP IF mod(num,10)=0 THEN -- extracting last digit of a number . r:=r||0; --if end digit is 0 then concat r with 0 ELSE r:=r||mod(num,10);--if mod is not 0 then it would be last digit. END IF; num:=trunc(num/10);--Removing last digit from number END LOOP; dbms_output.put_line(r); END;

  Read the article

• Concatenation with Zero is not occuring properly in code?

  - by Vineet

  I was trying to reverse a number in pl/sql ,its working fine but when my number contain any 0,output come unexpected .for eg 1234 output 4321 1000 output 1 1203 ouput 3021 10001 output 1 DECLARE r number(9); num number(9):=&p_num; BEGIN WHILE num>=1 LOOP IF mod(num,10)=0 THEN -- extracting last digit of a number . r:=r||0; --if end digit is 0 then concat r with 0 ELSE r:=r||mod(num,10);--if mod is not 0 then it would be last digit. END IF; num:=trunc(num/10);--Removing last digit from number END LOOP; dbms_output.put_line(r); END;

  Read the article

< Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >