Search Results

Search found 27 results on 2 pages for 'nvida'.

Page 2/2 | < Previous Page | 1 2 

  • Can not get sound over hdmi in kubuntu 9.10

    - by user32509
    I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :) Edit: lspci -v ... 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a022 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at ea400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel ... cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.20. lsmod | grep snd_hda_intel snd_hda_intel 31880 2 snd_hda_codec 87584 2 snd_hda_codec_realtek,snd_hda_intel snd_pcm 93160 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd 77096 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_page_alloc 10928 2 snd_hda_intel,snd_pcm I think I am missing the something-hdmi module? Is there such a thing?

    Read the article

  • Multi Monitor Setup Problems

    - by Shamballa
    I have Ubuntu 10.04 LTS - the Lucid Lynx. I have until recently been using a nVida Graphics card (NVIDIA GeForce 9800 GT) with two monitors attached, this all worked fine and dandy. A couple of days ago I bought two new identical LCD monitors for a multi monitor setup and two ATI graphics cards (ATI Sapphire Radeon HD5450). NOTE *All monitors work fine in Windows XP, 2k, Vista and 7 After I had booted into Ubuntu only one display came on, that I kind of expected anyway, then I removed the driver for the nVidia card and downloaded the ATI version which gave me the ATI Catalyst Control Center - in that only two of the displays were showing the third was disabled and showing unknown driver. I enabled the third monitor that stated "Unkown Driver" and had to reboot, upon reboot none of the displays work. I restarted and booted up into recovery mode and from now that is only what I can get into using a failsafe driver. It seems according to the log that a server is already active for Display 0 and I have to remove /tmp/.X0-lock and start again. This is what the log file is saying: Fatal Server Error Server is already active for display 0 if this server is no longer running, remove /tmp/.X0-lock and start again. (WW) xf86 closeconsole: KDSETMODE failed: Bad file descriptor (WW) xf86 closeconsole: VT_GETMODE failed: Bad file descriptor (WW) xf86 closeconsole: VT_GETSTATE failed: Bad file descriptor ddxSigGiveUp: closing log I have tried looking at my xorg.config file but unfortunately I have not really got a clue as to how it "should" be - I have tried regenerating it using this command from a terminal: sudo dpkg-reconfigure -phigh xserver-xorg but that had no effect so I am currently stuck in failsafe driver mode but two monitors are active but are mirroring each other. I hope that this is not to long - looking back I have been going on a bit! but I am just trying to explain as much as I can... I have asked this on Linuxquestions but nobody seems to know either or at least I have not had any responses. Could some kind soul please help explain what I can do from here? I would be eternally grateful. Chris * Update * Removing xorg.conf does nothing other than allowing me to use only two monitors - using the command: sudo aticonfig --initial generates the xorg.conf file below: but does not work either - I just get two monitors... Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 EndSection Section "Files" EndSection Section "Module" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection I have tried using this command from a thread on the Ubuntu Forums with a question similar to mine: sudo aticonfig --initial=dual-head --adapter=all Generated xorg.conf file Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen "aticonfig-Screen[0]-1" RightOf "aticonfig-Screen[0]-0" Screen "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-1" Screen "aticonfig-Screen[1]-1" RightOf "aticonfig-Screen[1]-0" EndSection Section "Files" EndSection Section "Module" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]-1" Driver "fglrx" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "aticonfig-Device[1]-0" Driver "fglrx" BusID "PCI:2:0:0" EndSection Section "Device" Identifier "aticonfig-Device[1]-1" Driver "fglrx" BusID "PCI:2:0:0" Screen 1 EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[0]-1" Device "aticonfig-Device[0]-1" Monitor "aticonfig-Monitor[0]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-0" Device "aticonfig-Device[1]-0" Monitor "aticonfig-Monitor[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-1" Device "aticonfig-Device[1]-1" Monitor "aticonfig-Monitor[1]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection This upon reboot renders ALL monitors blank and I have to go into recovery mode and use a failsafe driver. This is so much harder than I thought it would be, I don't think Ubuntu likes ATI for multi (3) monitors or maybe the other way around. Can anyone help still?

    Read the article

< Previous Page | 1 2