Search Results

Search found 36498 results on 1460 pages for 'linux usb drive'.

Page 20/1460 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• Nec USB 3.0 controller drops connection - Ubuntu 12.04.1

  - by Tom

  I have some serious problems with Technaxx pci-e 302p card. It has uPD720200a NEC chip with 4020 firmware. BIOS recognises it. Sometimes it recognises devices and system mounts them and are functional for few minutes, other times they can't be mount and error occours. After fresh install card worked fine, but after kernel and firmware update it behaves as mentioned. Outputs: uname -a Linux asd-GA-MA770-UD3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lspci -vvv USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fd8fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 07d1:3c0a D-Link System DWA-140 RangeBooster N Adapter(rev.B2) [Ralink RT3072] Bus 005 Device 004: ID 1997:1221 Bus 005 Device 003: ID 15c2:003c SoundGraph Inc. lsmod Module Size Used by nls_iso8859_1 12713 0 nls_cp437 16991 0 vfat 17585 0 fat 61512 1 vfat vesafb 13844 1 saa7134_alsa 18602 1 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep tda827x 18182 1 snd_hda_codec_hdmi 32474 1 ir_lirc_codec 12859 0 lirc_dev 19204 1 ir_lirc_codec tda8290 22616 1 arc4 12529 2 snd_hda_codec_realtek 224173 1 ir_mce_kbd_decoder 12777 0 ir_sony_decoder 12510 0 ir_jvc_decoder 12507 0 tuner 27428 1 ir_rc6_decoder 12507 0 snd_hda_intel 33773 5 rt2800usb 22684 0 rt2800lib 58925 1 rt2800usb crc_ccitt 12667 1 rt2800lib rt2x00usb 20762 1 rt2800usb rt2x00lib 51144 3 rt2800usb,rt2800lib,rt2x00usb mac80211 506816 3 rt2800lib,rt2x00usb,rt2x00lib ir_rc5_decoder 12507 0 rc_avermedia_m135a 12526 0 rc_imon_pad 12505 0 ir_nec_decoder 12507 0 cfg80211 205544 2 rt2x00lib,mac80211 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_ctxfi 111202 2 snd_hwdep 13668 1 snd_hda_codec imon 32839 0 snd_pcm 97188 5 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_ctxfi snd_seq_midi 13324 0 saa7134 181851 1 saa7134_alsa videobuf_dma_sg 19354 2 saa7134_alsa,saa7134 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi joydev 17693 0 rc_core 26412 13 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_avermedia_m135a,rc_imon_pad,ir_nec_decoder,imon,saa7134 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 101 videobuf_core 26390 2 saa7134,videobuf_dma_sg v4l2_common 16454 2 tuner,saa7134 videodev 98259 3 tuner,saa7134,v4l2_common sp5100_tco 13791 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 28 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_ctxfi,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device v4l2_compat_ioctl32 17128 1 videodev tveeprom 21249 1 saa7134 i2c_piix4 13301 0 soundcore 15091 1 snd edac_core 53746 0 serio_raw 13211 0 snd_page_alloc 18529 3 snd_hda_intel,snd_ctxfi,snd_pcm edac_mce_amd 23709 0 wmi 19256 0 mac_hid 13253 0 ppdev 17113 0 parport_pc 32866 1 k10temp 13166 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usb_storage 49198 0 uas 18180 0 usbhid 47199 0 hid 99559 1 usbhid firewire_ohci 41000 0 firewire_core 63558 1 firewire_ohci crc_itu_t 12707 1 firewire_core floppy 70365 0 pata_atiixp 13204 2 r8169 62099 0 dmesg | tail after plugging to usb 3.0 port [ 834.871296] sd 9:0:0:0: rejecting I/O to offline device [ 834.871308] sd 9:0:0:0: rejecting I/O to offline device [ 834.871319] sd 9:0:0:0: rejecting I/O to offline device [ 834.871330] sd 9:0:0:0: rejecting I/O to offline device [ 834.871530] sd 9:0:0:0: [sdd] Unhandled error code [ 834.871536] sd 9:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 834.871545] sd 9:0:0:0: [sdd] CDB: Read(10): 28 00 0e 8e 48 0a 00 00 3e 00 [ 834.871564] end_request: I/O error, dev sdd, sector 244205578 [ 834.875497] sd 8:0:0:1: Device offlined - not ready after error recovery [ 834.885339] usb 9-2: USB disconnect, device number 2 Are there any other outputs need for answering? I'll post them ASAP. I could of course reject updating the system but I think it's halfway solution. Any help appreciated. BTW USB 2.0 and 1.1 ports run well, card itself runs under win7 as charm. Tom

  Read the article

• What is so good about Linux? [closed]

  - by Chris Bridgett

  Self-explanatory question title. I've only ever used Windows OS's (except Mac OSX at friends etc, years ago occasionally) and when diving into the world of programming, Linux is a name that is coming up every other tutorial or article. All my web hosts run Linux and a lot of programming literature covers how to go about various tasks on Linux as well as Windows, but other than the odd raving I've read years ago about Linux being less resource-intensive, I haven't really given it much thought. Any article I read about Linux and whether it should be used for... 'regular' use, it's shunned since any windows applications I'm familiar with will usually require the windows API and there's no end of 'hacking' to get various programs working on Linux. As far as I understand a GUI is optional on Linux too? This all sounds very noobish I'm sure, but we all start somewhere, so: What is Linux good for? What should Linux be used for?

  Read the article

• "Could not claim interface on camera: -6" when trying to connect usb camera (Kinect)

  - by rzetterberg

  I have installed the freenect library from openkinect.org. With that library there is a demo application which you can run from the terminal to test out the Kinect. However when I run this command I get the following output: richard@behemoth:~$ sudo freenect-glview Kinect camera test Number of devices found: 1 Could not claim interface on camera: -6 Could not open device This particular error is thrown by the library libusb by the function libusb_claim_interface and the error -6 corresponds to the LIBUSB_ERROR_BUSY. So my guess is that it has something to do with mounting the usb, rather than specifically the freenect library or the Kinect itself. So my question is how can I find out what resource is using this interface and how can I free it so that I can access it? Edit: What I have tried so far (just to be sure): Rebooted Plugged-out, plugged-in Tried different usb ports Restarted udev Additional information that might be useful: /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation UUID=1c73f217-ac8d-451b-8390-7a680628a856 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=bb49bd29-07ec-45a0-bbab-46fb8362b06b none swap sw 0 0 sudo uname -r: Linux behemoth 3.0.0-14-generic-pae #23-Ubuntu SMP Mon Nov 21 22:07:10 UTC 2011 i686 i686 i386 GNU/Linux cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10"

  Read the article

• Linux Mint 13 64bit Cinnamon and Oracle Virtualbox: 3d acceleration crash

  - by Stephen Swensen

  I've recently got an interest in Linux. After some research, it looks like Linux Mint 13 cinnamon is hot and I thought I'd try it out... I'm running Windows 7 64bit and have experience with Oracle Virtual Box. So I thought it would be a good idea to try out Linux Mint inside Virtual Box. I download Linux Mint 13 64bit Cinnamon and set it up in my VM player... Nothing special about my settings. Except Linux Mint 13 Cinnamon requires 3d acceleration, and when I enable that, it crashes whenever I open the Menu in the bottom left corner of the guest OS (and some other times too)... I've seen other mentions of this problem on the web, but no solutions. Is there a solution? If not, any suggestions short of installing the OS on a partition for trying out this OS (I'm not interested in the LIve mode either - I'd really like to get the full feel for it)?

  Read the article

• Linux Mint something wrong with my .bashrc

  - by user2309862

  The path of my .basrc file is /home/vamsi/.bashrc It is weird that my file has nothing but the path I set. I think I am using a file at the wrong location or that I have lost my .bashrc file as none of the environment variables set here seem to work. #ANDROID_DEV ANDROID_HOME=/opt/android-sdk-linux export ANDROID_HOME PATH= $PATH:$ANDROID_SDK_HOME/tools export PATH PATH=$PATH:$ANDROID_HOME/platform-tools export PATH PATH=$PATH:$ANDROID_HOME/build-tools export PATH #MAVEN-PATH M2_HOME=/opt/apache-maven-3.1.0 export M2_HOME M2=$PATH:$M2_HOME/bin export M2 I was prompted to install maven2 in order to use mvn, but the android command cannot be found. Could you please help me find a solution to this issue. EDIT: Meanwhile,I tried this: export PATH=${PATH}:/opt/android-sdk-linux/platform-tools export PATH=${PATH}:/opt/android-sdk-linux/tools Now,the output of $PATH echoes: bash: /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/opt/android-sdk-linux/platform-tools:/opt/android-sdk-linux/build-tools: No such file or directory

  Read the article

• USB mouse disconnecting and reconnecting in windows and linux

  - by Kalak

  I have a problem similar to what is described at "Why is my USB mouse disconnecting and reconnecting randomly and often?" except is is happening in both Windows 7 and Linux (Ubuntu 12/04TLS, fully patched), multiple mice, multiple OSs. It stops responding to input for about 3-5 seconds, then starts responding again. It's more frequent and lasts longer when running games (TF2, L4D, Dishonored, Borderlands 2, and more), but happens when just running the OS as well. I was hoping it was the motherboard so I bought a USB 2.0 PCI card to try that, but it's still happening. I've stripped it down to just the keyboard and mouse (different keyboard too just in case the keyboard was the problem), but it's still happening. All the hardware (mice and keyboards) work fine on other computers. I have literally pulled the mouse and keyboard out and plugged them into another computer (laptop) and re-joined the online game and had no problem with the keyboard and mouse combo that just failed on my gaming rig. Please no driver / Windows or Linux only suggestions, as that wouldn't effect both OSs. edit: known good mice I've brought home are now going bad. I suspect the hardware is messed up (voltage?) and has been frying the mice.

  Read the article

• Arch Linux Terminal (via ssh) + Dropbox but sync only 1 single selected folder

  - by Norfeldt

  Sorry for the weird title... I'm (still) quite new to linux and are doing shh commands to an Arch Linux device that has not screen output options. So everything has to be done in the terminal (not my super element). I use the linux device to play around with python (which is quite fun). Now I would like sync my script folder with dropbox. Since I don't have enought space to sync all my dropbox files to the device, I would like to know how I can set it up in a way that it only syncs with the folder I choose. At the time being I have not installed dropbox because I'm afraid that it will immediately begin to sync all my dropbox folders onto my linux device. BONUS INFO: I already have created a folder in my dropbox that I that contains some py scripts I would like to have synced with my linux device.

  Read the article

• Using UDF on a USB flash drive

  - by CesarB

  After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

  Read the article

• USB drive errors after airport scan

  - by bobobobo

  Well, I just got a new PNY usb drive and it passed through an airport scanner yesterday. For some reason, I wrote to it and then tried to read from it today, and it gave me a corrupted error! chkdsk reports errors like: Bad links in lost chain at cluster 1179 corrected. Lost chain cross-linked at cluster 1200. Orphan truncated. Lost chain cross-linked at cluster 1228. Orphan truncated. Lost chain cross-linked at cluster 1236. Orphan truncated. Lost chain cross-linked at cluster 1237. Orphan truncated. Lost chain cross-linked at cluster 1244. Orphan truncated. Lost chain cross-linked at cluster 1250. Orphan truncated. Lost chain cross-linked at cluster 1266. Orphan truncated. Lost chain cross-linked at cluster 1278. Orphan truncated. etc. What is this from? Could it possibly be from the airport scanner, or is it likely a defective USB chip? How can I check the chip to see if I should just return/throw it away or continue to use it?

  Read the article

• optimal folder structure for storing 100k files on a USB drive

  - by cherouvim

  I need to store 100k files (around 40GB) in a USB drive. Each file has a unique int id (e.g 45000). Option one is to put all files in a single folder: root/ root/1.pdf root/2.pdf root/3.pdf ... root/567.pdf root/568.pdf root/569.pdf ... root/10001.pdf root/10002.pdf root/10003.pdf ... root/99998.pdf root/99999.pdf root/100000.pdf Option two is to create a [1-9][0-9]* folder hierarchy based on that id: root/ root/1/file.pdf root/2/file.pdf root/3/file.pdf ... root/5/6/7/file.pdf root/5/6/8/file.pdf root/5/6/9/file.pdf ... root/1/0/0/0/1/file.pdf root/1/0/0/0/2/file.pdf root/1/0/0/0/3/file.pdf ... root/9/9/9/9/8/file.pdf root/9/9/9/9/9/file.pdf root/1/0/0/0/0/0/file.pdf Which option will scale better? I can understand that the second option will require tons of folders but each folder will at most contain 10 folders and 1 file. Maintenance will not be an issue since everything will be controlled by an application. Note that this is a USB drive on linux and based on the above I'd also like to know whether I should go with FAT32 or NTFS.

  Read the article

• External HDD connecting via USB disconnects wireless LAN connection

  - by Kensai

  Strange problem. I have this MEDION Akoya PC that has a dedicated bay to slide an external HDD sold separately. It's very handy indeed cause the slot is providing a fast USB 3 connection and power to the HDD unit, without extra cables. All works fine except this show-stopper behavior to disconnect me from the router once I slide in the unit and it powers up. The moment I connect the unit the (normally) three-four WiFi connections I see in my neighborhood disappear and my own to the router loses its signal strength (no Internet traffic is possible). After a while it throws me off that one as well, never to connect me again as long as the unit is powered. Once I disconnect the HDD the various signals come back and it automatically reconnects to my own. What takes? Are we in front of a serious design fault by MEDION here? Does the spinning of the HDD on top of the PC cause electromagnetic interference strong enough to throw off my WiFi connectivity? Is it a simple USB problem? Some kind of strange hardware conflict? Where should I look?

  Read the article

• Hard Drive that was used before not detected or accessible in Windows 7

  - by Anders

  Hello SU: My PC crashed for some unknown reason, and I am still working on what caused that. However, I pulled my main (windows) drive from my computer and hooked it up to my roommate's machine and was able to pull the data I needed off of it (i.e. the drive is good). I hook up his drives as they were, I had to turn off his machine and unplug his secondary drive to hook mine up, boot his machine and there is no second drive available in windows explorer. I opened Device Manager to see if for some reason it's drive letter got un-assigned, but there is nothing listed in there except his primary hard drive, his optical drive and one other optical drive which I believe is the virtual drive Daemon Tools made. The drive shows up in the BIOS, however after I restarted his machine again it sits on the "Entering setup....." screen at the load window. The only thing I can think of is that may have messed with stuff is I used this tutorial to create a bootable XP install on a USB drive to install XP on my machine (I am 99% certain that the optical drive in my PC is broken) and maybe it used the other hard drive's letter for the USB drive for some reason, which doesn't make much sense since it was recognized it as a different drive letter before I started the process. It is possible that it used the secondary hard drive's letter for it's work, but once again I am uncertain. Where should I go from here? He his bound to wake up within the next several hours and will probably flip a lid if I cannot get some sort of handle on this. Any and all help is greatly appreciated. PS: Anyone who helps me get this situated has a beer or two on me, as long as you are in the greater metro Detroit area, or don't mind traveling a bit!

  Read the article

• How to partition USB drive for Ubuntu installation?

  - by Heather

  I am not a computer savvy and need to know how to partition my USB drive without messing up my laptop. I already have the boot order set up properly and the USB drive already has the ISO image downloaded onto it. I am ready for install but just do not know how to partition. I am installing Ubuntu 12.4 LTS onto a USB. Can someone help me? I need an easy walk through please. What I need to know is from the screen shots above do I use the swap drive and if so how do i partition that drive to be my drive? I am stuck up to this part on the installation process. Yes please make a list of the steps for me.

  Read the article

• Google Drive SDK: Publishing your website on Google Drive

  Google Drive SDK: Publishing your website on Google Drive In this session we'll show you a new feature of the Google Drive SDK: the ability to publish a website from a Google Drive folder. We'll show you a brief demo involving cute animals, but don't worry, no kittens will be harmed in the process! From: GoogleDevelopers Views: 0 3 ratings Time: 03:30:00 More in Science & Technology

  Read the article

• Multiple Internet connections, multiple networks and split access in Linux

  - by Swapneel Patnekar

  I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

  Read the article

• What causes "All-in-one USB Card Reader" to create 6 drives that always appear in Disk Management?

  - by tim11g

  I installed a "All-in-one USB Card Reader" to read SD cards and other media. It has caused six new drives to appear in Disk Management with six new drive letter assignments. These drives and letters are always present, even when there are no cards in the reader. When unused, they are labeled "No Media". Why does this multifunction reader cause these phantom Disks to appear and consume drive letters? Every USB port can (and does) allow removable media to be mounted and assigned a drive letter, and the drive letter assignment "disappears" when the USB drive is removed. Why are these card reader's drives and letters staying allocated permanently? Is there anything that can be done to make the slots work like a typical USB drive? (The reader is in fact connected to USB).

  Read the article

• Linux for a laptop? [closed]

  - by spriteless

  I would like to install Linux on a laptop. So I have emptied the hard drive, and can boot off a CD. So far I have failed to format the hard drive to Linux, to install Linux, and to change it so that I don't have to hit escape when loading in order to boot from CD (or get Linux on the hard drive and boot to it). The old laptop has 640 MB RAM, 600*800 screen, a CD drive and USB mouse and floppy drives. I eventually mean to use it to look at PDFs if possible, or RTFs that I converted from PDFs if not.

  Read the article

• usb hub not working on resume from suspend

  - by user1781498

  All the usb ports on my laptop work but when I resume from suspend some the usb ports don't work. lsusb Before Suspend: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 04f3:014b Elan Microelectronics Corp. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 04f2:b3a6 Chicony Electronics Co., Ltd Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsusb After Suspend: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 04f3:014b Elan Microelectronics Corp. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Ubuntu live session crashes and boots to a black screen

  - by Bsc

  I heard about Ubuntu from a friend and wanted to test it out. I made a Pendrive Ubuntu 12.04 with a persistent file using Universal USB Installer. The first time I booted Ubuntu from the USB everything went like usual. I was just a bit exploring Ubuntu and had installed a few apps nothing more. Today after using Windows 7 for while again, I wanted to boot Ubuntu again. When I boot it, the usual loading screen comes up but after that it crashes and gave me a black screen. Is there a possibility to check the USB on errors or do I need to reinstall Ubuntu on the USB?

  Read the article

• Intel RST accidentally selected wrong drive as system drive -- how to fix?

  - by Sean Killeen

  Question / TL;DR If Intel RST has marked a drive other than my RAID set as the system drive, how can I get it so that the RAID set is now seen as the system drive, and catch it up to my drive now? What Happened NOTE: Some perhaps unwise decisions are ahead. This is as best as I can recall the order of things. I had a 2x1TB RAID1 config. I bought the drives around the same time, and they started to die around the same time. I replaced 1st drive with a 2 TB drive before the other one's SMART errors got more serious. I waited for the RAID to replicate, then replaced the 2nd drive with a manufacturer's replacement. I got a second manufacturer's drive replacement and used it as a spare. so I now I had a 1TB/2TB drive in a RAID1 and another 1TB as a spare. The 1TB drive in the replacement set was bad from the manufacturer. Rather than mess with their refurbished stuff, I bought another 2 TB drive an upped the config to a 2x2TB RAID1 with the other, functioning manufacturer's drive as a spare. I made the mistake of trying to bring the other drive online to clean it out and the signatue clash killed my machine. When the machine rebooted, that drive was marked as the system drive. So, I have a 2x2TB RAID1 that is apparently offline, and 1 spare 1 TB refurbished drive that everything is being run from. Not a great idea. Options I'm considering Bring the 2x2TB drive back online, and then unplug the spare until I can format it in another system. This would involve some data loss, but the more I think about it, I actually think I haven't modified any data that isn't backed up or synced somewhere (go me!) Anything that isn't is likely trivial, enough that I'm willing to take the risk. One downside here is that if the 2 TB doesn't have data on it for some reason, I could be screwed trying to put the other drive back in, no? Try to somehow get the RAID1 updated with the data from the current system drive. Option 3?

  Read the article

• install grub on pendrive containing linux installation, making it system independent

  - by arpit

  i have a win7 system and i want to install debian 6 on usb flash drive. the problem is grub loader. i want to install the grub loader on usb itself, so i can just plug in the pendrive in any computer and boot to deb6. so in effect making the flash drive an independent system. i tried it earlier, but ended up with grub loader needing me to insert the pendrive every time to give me boot options to even boot the win7 system, even though it was on primary hdd. so is there a way to turn the pendrive into full linux system with own boot loader, which can automatically detect os in the system i plug it in and be able to boot any of them. totally, self sufficient and system independent; making the pen drive so that it only needs a host system to run the os it carries. thank you, waiting for replies.

  Read the article

• Linux kernel - can't access sda16 & sda17

  - by osgx

  I can't access sda16 sda17 and higher partitions from my linux. This linux is rather debian (very old); kernel 2.6.23. So, I know that so old linux kernel can't access 16 partitions on single sata disk. What version of kernel should I use to be able access sda16, sda17 etc? I want to update only a kernel, not a whole Linux distribution. PS. There is an WindowsNT kernel which can access and format 16, 17 or higher partition, but my intention is to use sda16 and sda17 from linux (I want Linux Kernel). PPS: dmesg: sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 > sd 2:0:0:0: [sda] Attached SCSI disk sd 4:0:0:0: [sdb] xxx 512-byte hardware sectors ... So, there is no mapping of sda16, sda17, ... to sdb. Sdb is the second physical hard drive.

  Read the article

• How to install my currrent Ubuntu based OS on to an extenal drive?

  - by Godel Fishbreath

  I have found urls to install ubuntu to a HD. But my current system has been upgraded and updated so often that it does not resemble anything on the web or on my drive disks. So giving my a url to how to install ubuntu will fail. Give me instead 'how to install my current Linux/Ubuntu based system (11.04) and all the upgrades to my external HD. Or alternately how to back up the OS into a bootable external HD. I am looking for either urls or a very complete explanation.

  Read the article

• How to make Ubuntu LiveCD be able to use USB Flash drive and external hard drive?

  - by ????

  I am booting up Ubuntu 2012.04 LiveCD... and was able to do /sudo mount /dev/sda1 /mnt and be able to see files in /mnt, which is the main hard drive that can't boot up any more. So to copy files from /mnt to an external hard drive or USB flash drive, I connected a 1TB external hard drive and 2 USB flash drives to the computer, but for some reason, in "File Systems", I can't drag and drop files from /mnt into those external hard drive or USB flash drives? I can't open or look into those drives either... How to make it work?

  Read the article

• Creating an install drive - can not open output file autorun.inf

  - by user226881

  I am trying to make an install/boot drive for a computer that has no operating system and no optical drive. I used the ISO from Ubuntu.com and the burner from pendrivelinux.com. When the program starts writing to the flash drive, there is an error displayed that says : "0 can not open output file E:\autorun.inf" But continues to write data. After it has finished, I remove the drive and insert to the other computer and turn it on, but it never finds a drive to boot from. What is causing this problem and how can I fix it ?

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >