Search Results

Search found 10169 results on 407 pages for 'port'.

Page 200/407 | < Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >

  • Using iptables to forward traffic destined for specific ip via specific interface

    - by shapeshifter
    I want to forward traffic destined for a specific ip from my internal network via a specific interface. I have two interfaces which are currently load balanced. I need all requests for a certain ip to go out via eth0 otherwise my external ip changes and sessions are dropped. eg. all requests from 10.1.1.1/24 to ip 11.22.33.44 on port 443 must go out via interface eth0. How can I do this with iptables?

    Read the article

  • outbound ftp on server 2008 r2 stalls

    - by Scott Kramer
    the built in command line ftp client in server 2008 does not support passive mode so I've used these commands to allow outbound ftp (it stalls without this) 1) Open port 21 on the firewall netsh advfirewall firewall add rule name="FTP (no SSL)" action=allow protocol=TCP dir=in localport=21 2) Activate firewall application filter for FTP (aka Stateful FTP) that will dynamically open ports for data connections netsh advfirewall set global StatefulFtp enable however in server 2008 r2, these commands seem to work, but it does not affect the outbound ftp, it stalls I do not want to use an alt client

    Read the article

  • Spanning-Tree and redundant links

    - by Franko
    I have 2 switches which have redundancy between them, meaning fa0/1 on SW1 is connected to fa0/1 on SW2, and fa0/2 on SW1 is connected to fa0/2 on SW2. Both of the switches have the same BID, however the MAC address of SW1 is numerically lower, hence making it the root bridge. Now my question is, on SW2, what determines which of fa0/1 and fa0/2 becomes the RP (Root Port) and the other on blocking state?

    Read the article

  • Can SSH be tunneled over HTTPS using thttpd?

    - by Michael
    I need to tunnel my SSH server through an HTTPS port using thttpd (I can change to lighttpd if necessary, but I'm trying to avoid installing Apache since it's an underpowered box). I haven't been able to find anything that confirms or denies this ability of thttpd.

    Read the article

  • how to have a vm image act as a server host

    - by tipu
    I have a VM Ware player, VMware-player-3.0.1-227600.exe I downloaded a cent os image, it's version is CentOS release 5.4 (Final) I have apache installed and listening on port 8080. However when I visit my ip address, x.x.x.x.:8080/ I don't get the default apache page as I would by going to localhost:8080/ What do I have to do in my image or vmware to get it to serve?

    Read the article

  • telephone sockets connecting them to an ATA

    - by ageis23
    We have many extension sockets in the house therefore be fairly expensive to buy an ata for each phone. Since extension sockets are daisy chained together, could I just plug it into the FXS socket instead of the BT master socket? Or is the FXS port strictly for one phone only?

    Read the article

  • Is it possible to open server ports on TUN devices?

    - by JosephH
    If I make a VPN connection to a server (say myvpn.com; assume this server is not behind any router/firewall) via a TUN device and open a port (say 5555), will someone else be able to connect to me via myvpn.com:5555? If not, is there a tunneling software that does exactly this in a transparent manner? i.e. run any TCP/UDP-based server instance behind a router without NAT using another remote server.

    Read the article

  • Discovering proxy servers on a private network

    - by AIB
    Suppose that I am in a private network of computers (say each having ip addresses 192.168.. ). Some of the machines( we have no information regarding their ip, name and no physical access to the servers) in the network are connected to internet and they run an http proxy at some port say 3128. Is there a program which can be run on Windows or Linux which will give me the list of machines(ip addresses and ports if possible) acting as proxy servers?

    Read the article

  • Basic iptables for a webserver: SSL Tomcat, postgres, ssh and that's it.

    - by Paperino
    This is probably as basic as it gets but I'm a developer and really have no experience with iptbles. The only connections I need opened are: eth0 (outward facing) ssh ping SSL to tomcat (forward port 443 to 8443) eth1(local subnet) connection to postgres server Everything else should be blocked. My current attempts seem to be leaving all other ports open. I wonder what gives. Thanks serverfault!

    Read the article

  • Benefits of setting a webserver in Linux

    - by John Kent
    I wonder what main purposes and benefits can one get after he sets up a webserver running on Linux installed on a VM which is hosted by Windows and that this webserver can be used as a local host for windows ? That is, I have java application that is a webserver made on Linux, I set up the virtual machine for the windows client apps to listen to its (Linux)'s local IP address and port e.g 192.168.50.50:11111 When my webserver runs, I can use http://192.168.50.50/ as the windows's localhost address (instead of 127.0.0.1 as I usually do). Thank you

    Read the article

  • Error handling pppd configuration?

    - by Sebastian
    I have a computer, running ubuntu, that I want to be connected to the network at all times. It has a GSM modem connected to it via USB. Is there some program available that monitors that the networking is working (by pinging some site(s)), and if not tries to fix the error by reseting the modem, reloading the USB drivers and perhaps by dropping the USB port's current (if possible) to force the modem to reset ?

    Read the article

  • Remote Desktop over VPN or SSH?

    - by Jonathan
    I want to provide a remote employee remote desktop into a PC in the office and am trying to decide between the following two options: Use Microsoft VPN to get him a local network IP. Use RDP to connect to host machine. Use local SSH tunneling for VPN port. Connect RDP to localhost:portNumber Is either option more secure than the other? Will either option perform better than the other? Are there any better options I've missed or considerations I should make?

    Read the article

  • Continuously check nestat output for a particular program

    - by Vihaan Verma
    I have a android emulator running on port 5554. I want to continuously watch the netstat output concerning emulator stuff. right now I have to manually execute this command every time sudo netstat -plant | grep emulator I thought doing something like this would repeat above command automatically every 2 sec. watch sudo netstat -plant | grep emulator but instead it hangs the terminal. How to achieve such functionality ? Thanks

    Read the article

  • Squid on windows loadbalancing only to one server

    - by Martin L.
    After thousands of googles and trying days i cant get the load balancer/failover in squid on windows to work. Iam using squid 2.7. My webservers are 2 single NIC lighttpd and one dual nic lighttpd. server1 in this example is running squid on port 80 and lighttpd on port 8080 (just to test) Requirements: All 3 webservers running lighttpd should be balanced two option for load balancing: Best would be if server1 is busy server2 takes over, if server2 is busy server3 takes over, etc.. Round robin style evenly distributed load. Eg server1 takes first call, server2 second etc.. All requests should be treated the same way (no url rewriting or so on) Sent host headers have to be redirected to every server as http host header, speaking of "server1", "server1.company.internal" and "10.211.1.1". My approach: acl all src all acl manager proto cache_object http_port 80 accel defaultsite=server1.company.internal vhost #reverse proxy entries cache_peer 10.211.2.1 parent 8080 0 no-query originserver round-robin login=PASS name=server1_nic1 cache_peer 10.211.1.2 parent 80 0 no-query originserver round-robin login=PASS name=server2_nic1 cache_peer 10.211.2.3 parent 8080 0 no-query originserver round-robin login=PASS name=server3_nic1 cache_peer 10.211.2.4 parent 8080 0 no-query originserver round-robin login=PASS name=server3_nic2 #decl of names of squid host acl registered_name_hostdomain dstdomain server1.company.internal acl registered_name_host dstdomain server1 #ip of squid host acl registered_name_ip dstdomain 10.211.2.1 # access: redirects the correct squid hostname http_access allow registered_name_hostdomain http_access allow registered_name_host http_access allow registered_name_ip http_access deny all cache_peer_access server1_nic1 allow registered_name_hostdomain cache_peer_access server1_nic1 allow registered_name_host cache_peer_access server1_nic1 allow registered_name_ip cache_peer_access server2_nic1 allow registered_name_hostdomain cache_peer_access server2_nic1 allow registered_name_host cache_peer_access server2_nic1 allow registered_name_ip cache_peer_access server3_nic1 allow registered_name_hostdomain cache_peer_access server3_nic1 allow registered_name_host cache_peer_access server3_nic1 allow registered_name_ip cache_peer_access server3_nic2 allow registered_name_hostdomain cache_peer_access server3_nic2 allow registered_name_host cache_peer_access server3_nic2 allow registered_name_ip cache_peer_access server1_nic1 deny all cache_peer_access server2_nic1 deny all cache_peer_access server3_nic1 deny all cache_peer_access server3_nic2 deny all never_direct allow all Problems: Load balancer does not load balance other than to first server. Only if the first server is killed in any way the second will take over. I have seen the others working at some point, but definitely not as the intended load balancing described above. If the cache_peer_access is not defined sometimes the wrong hostname is sent to the backend webserver and this always depends on the defaultsite= parameter. Probably because the host header on the request to squid is not set and its replaced by defaultsite. Leaving out defaultsite didnt solve the problem. The only workaround i found for this is the current approach with cache_peer_access. Questions: Does the cache_peer_access influence the round-robin? Is there a better workaround to pass the host header to the backed webservers? Which parameters do increase the speed of load balancing or does anyone have a better approach? -Martin

    Read the article

  • Setting external IP for Citrix Web Interface

    - by Callum Jones
    I have a Citrix Web Interface (as part of XenApp 6.0 on Windows Server 2008 R2) that is behind a NAT, I can access the web interface fine (via both SSL and standard port 80) but when I go to launch a application that connection is still being made over the server's internal IP address. How do I configure the web interface to default to the external IP address of the box instead of its internal LAN IP?

    Read the article

  • Remove USB device from command line

    - by Luke
    I'm constructing a backup script for Windows 7, and the last action I want it to perform is to safely "remove" the USB drive that it is backing up to. I am under the impression that plugging the drive into the SAME USB port all the time will keep the same DEV_ID, correct me if I'm wrong. With a Command Line (or PowerShell), how can I tell Windows to safely remove the hardware automatically without user input? Just as a place holder, other OSes that may have a way to do this would be great to know as well

    Read the article

  • FC SAN network high-error rate simulation

    - by Wieslaw Herr
    Is there a way to simulate a malfunctioning device or a faulty cable in a FC SAN network? edit: I know shutting down a port on a switch is an option, I'd like to simulate high error rates though. In an ethernet network it would be a simple case of adding a transparent bridge that discards a given percent of the packets, but I have absolutely no idea how to tackle that in an Fibre Channel environment...

    Read the article

  • Exchange not delivering the mail

    - by wolfvilleian
    I'm having an issue where my Exchange Edge Transport server receives mail (found in logs) and then it vanishes, never ending up in the users mailbox, I have a edge subscription setup between it and the main Exchange server, how can I go about tracing the message to figure out what is broken? I also have found records of the message in the logs on the main Exchange server. Thanks a ton for any help Edit: If I change port 25 on my main router to point to the main exchange server as opposed to the Edge Transport, email comes through fine form external domains and delivered in the correct mailbox

    Read the article

  • I have a problem with FTP service.

    - by Diego
    HI, I follow your istruction and everythig works. I have an DHCP server than it assign "Ip client" without gateway. Internet with IE or Firefox Browser works but FTP service doesn't work. In squid.conf I have put a line: acl Safe_ports port 80 21 443 389 5307 8080 3144 8282 88 8443 20443 11438 1443 8050 30021 10443 4747 4774 1384 Have I to put gateway in DHCP Server? Have you any suggestion for me? Thanks for your help

    Read the article

  • Reverse proxy a directory through IIS 6 with HTTPS

    - by John P
    I have an asp.net based website running on IIS 6 that needs to incorporate a java application running on the same server on a different port. The requests will be coming in via https and I need to invisibly (preserving the https session) proxy domain.com/ over to domain.com:8080/. Does IIS have a built-in mechanism for doing this? If not, are there any reliable free/open source ISAPI extensions that allow it? Thanks in advance

    Read the article

  • IPTABLES route, redirect, forwardc traffic

    - by Anthony
    I am trying to redirect traffic from one IP reached on a specific port to a website. For example I have two external ips, lets say 194.145.63.1 and 194.145.63.2 set on one network card as 194.145.63.1 - eth0 and 194.145.63.2 -eth0:1 mywebsite.com allows access only from 194.145.63.1 and I want to set my rules like if I hit http://194.145.63.2:8080 to open mywebsite.com trough 194.145.63.1. Thanks in advance!

    Read the article

  • How do I Implement Per VLAN Rate Limiting or QOS for a Cisco 2960?

    - by evolvd
    I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960? class-map match-any VLAN50-51-52 match vlan 50-52 class-map match-any VLAN53 match vlan 53 policy-map 50MB_RATE_LIMIT class VLAN50-51-52 police 50000000 5000000 exceed-action drop class VLAN53 police 350000000 35000000 exceed-action drop ! interface GigabitEthernet0/23 service-policy output 50MB_RATE_LIMIT service-policy input 50MB_RATE_LIMIT

    Read the article

  • ssh client problem: Connection reset by peer

    - by yonix
    I'm having a really annoying problem on my Ubuntu laptop. I noticed it today, after upgrading to Ubuntu 11.04, although I'm not entirely sure this is the cause as I played with my ssh keys a few days ago. The problem is, whenever I try to ssh to ANY host I get the following error: Read from socket failed: Connection reset by peer running with -vvv gives the following output: OpenSSH_5.8p1 Debian-1ubuntu3, OpenSSL 0.9.8o 01 Jun 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to hostname [10.0.0.2] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/id_rsa type -1 debug1: identity file /root/.ssh/id_rsa-cert type -1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: identity file /root/.ssh/id_dsa-cert type -1 debug1: identity file /root/.ssh/id_ecdsa type -1 debug1: identity file /root/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 1.99, remote software version OpenSSH_4.2 debug1: match: OpenSSH_4.2 pat OpenSSH_4* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1 Debian-1ubuntu3 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "hostname" from file "/root/.ssh/known_hosts" debug3: load_hostkeys: loaded 0 keys debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer My /etc/ssh/ssh_config: Host * SendEnv LANG LC_* HashKnownHosts yes GSSAPIAuthentication no GSSAPIDelegateCredentials no I can connect to my laptop from any other server via ssh, and I can also ssh localhost from my laptop successfully. I can connect to all these other server from other laptops, and I don't see anything in the logs of the other servers regarding my failed attempt. I tried to stop iptables, didn't help. I tried several tricks I could find online with my /etc/ssh/ssh_config, but I was unsuccessful in solving the problem... Any ideas? Edit: This is the log from one of the hosts I try to connect to: May 1 19:15:23 localhost sshd[2845]: debug1: Forked child 2847. May 1 19:15:23 localhost sshd[2845]: debug3: send_rexec_state: entering fd = 8 config len 577 May 1 19:15:23 localhost sshd[2845]: debug3: ssh_msg_send: type 0 May 1 19:15:23 localhost sshd[2845]: debug3: send_rexec_state: done May 1 19:15:23 localhost sshd[2847]: debug1: rexec start in 5 out 5 newsock 5 pipe 7 sock 8 May 1 19:15:23 localhost sshd[2847]: debug1: inetd sockets after dupping: 3, 3 May 1 19:15:23 localhost sshd[2847]: Connection from 10.0.0.7 port 55747 May 1 19:15:23 localhost sshd[2847]: debug1: Client protocol version 2.0; client software version OpenSSH_5.8p1 Debian-1ubuntu3 May 1 19:15:23 localhost sshd[2847]: debug1: match: OpenSSH_5.8p1 Debian-1ubuntu3 pat OpenSSH* May 1 19:15:23 localhost sshd[2847]: debug1: Enabling compatibility mode for protocol 2.0 May 1 19:15:23 localhost sshd[2847]: debug1: Local version string SSH-2.0-OpenSSH_5.3 May 1 19:15:23 localhost sshd[2847]: debug2: fd 3 setting O_NONBLOCK May 1 19:15:23 localhost sshd[2847]: debug2: Network child is on pid 2848 May 1 19:15:23 localhost sshd[2847]: debug3: preauth child monitor started May 1 19:15:23 localhost sshd[2847]: debug3: mm_request_receive entering May 1 19:15:23 localhost sshd[2848]: debug3: privsep user:group 74:74 May 1 19:15:23 localhost sshd[2848]: debug1: permanently_set_uid: 74/74 May 1 19:15:23 localhost sshd[2848]: debug1: list_hostkey_types: ssh-rsa,ssh-dss May 1 19:15:23 localhost sshd[2848]: debug1: SSH2_MSG_KEXINIT sent May 1 19:15:23 localhost sshd[2848]: debug3: Wrote 784 bytes for a total of 805 May 1 19:15:23 localhost sshd[2848]: fatal: Read from socket failed: Connection reset by peer

    Read the article

  • Log ports opened by an application

    - by Simon A. Eugster
    I'm searching for something like: tcpdump -p PID # But tcpdump does not know the PID or lsof -i --continuous # But lsof just runs and exits, no «live logging» to log which connections an application opens. In my case, I want to find out to which port git connects when committing. This happens in a fraction of a second, so I cannot use lsof. If there is a lot of traffic, filtering by PID or process name would be useful.

    Read the article

< Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >