Search Results

Search found 54202 results on 2169 pages for 'jqgrid asp net'.

Page 2041/2169 | < Previous Page | 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048  | Next Page >

  • How to enable Ipv6 on my ubunutu 11.04 virtual machine

    - by liv2hak
    I have installed 3 VM's on my PC.(Ubuntu 11.04).I want to setup an IPV6 network to review and test some of the IPV6 tools like NDPMonitor.(monitors ICMP messages of Neighbour Discovery Protocol.) IP v6 addresses are as follows. linux_router - fe80::a00:27ff:fed5:f7e9/64 labhack1 - fe80::a00:27ff:fed2:8bd1/64 labhack2 - fe80::a00:27ff:fed7:2f2d/64 The below commands have been run on both linux_router and labhack1. sudo ip r a 2001:468:181:f100::/64 dev eth0 sudo vim /etc/radvd.conf /file looks like below./ interface eth0 { AdvSendAdvert on; /*means that we are sending out advertisments.*/ MinRtrAdvInterval 5; /*these options control how often advertisments are sent*/ MaxRtrAdvInterval 15; /*these are not mandatory but valueable settings.*/ prefix fe80::a00:27ff::/64 { AdvOnLink on; /*Says to the host everyone sharing this prefix is on the sam local link as you.*/ AdvAutonomous on; /*Says to a host: "Use this prefix to autoconfigure your address"*/ }; }; sudo sysctl -w net.ipv6.conf.all.forwarding=1 I try to do a ping6 -I eth0 fe80::a00:27ff:fed5:f7e9 I get Destination unreachable: Address unreachable.I am not sure what I am doing wrong here.I am a beginner at linux administration.Basically I think I am missing whatever is analogous to physically connecting VM's.Any help that would point me in the right direction would be greatly appreciated.

    Read the article

  • Multiple Internet connections, multiple networks and split access in Linux

    - by Swapneel Patnekar
    I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

    Read the article

  • ASUS EAH5450 Graphics Card (ATI Radeon HD5450 - 1 GB DDR3) on Windows 2003? Anybody got it to work?

    - by JJarava
    Hi all! I've just bought an ASUS EAH5450 Graphics Card (ATI Radeon HD5450, 1 GB DDR3) for my main system, but I haven't been able to make it work under Windows 2003 (my OS in that system). When I plugged the card, I got a couple of "installing drivers" prompt for things such as "ATI High Definition Audio Device" that got themselves sorted out of the Internet, and then a "Standard VGA Graphics Adapter". The CD that came with the card installs something called "ATI Catalyst Install Manager" and .net 2.0, but no drivers. I've downloaded the latest (WinXP 32bits) drivers from ATI, and the experience is the same: I don't get any drivers installed. My Motherboard is an ASUS A8N-SLI with nVidia nForce 4 chipset (for an Athlon 64X2, somewhat old), but my previous card was an ATi Radeon X700, so it's been working with ATI cards before. On POST, during boot I see a "Display Card" Device (Vendor ID 1002-68F9-0300) and a "Multimedia Device" (1002-AA68-0403), and when viewing the properties of the "Standard VGA", they match the device ID. Any hints? I'd really hate having to get rid of the card, and I'm sure it's not that strange what I'm trying to do...

    Read the article

  • Internet slowed down because of SQUID Server setup

    - by Ranjith Kumar
    Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

    Read the article

  • Talk on multiple IRC channels at once?

    - by TwoPixelGrid
    I seem to remember, back in '91 or so, that the console-based IRCII implemention on the Solaris box that first got me on the net would let me /Join multiple channels on a given network such that, as new channels were joined, they would start scrolling to the single console view. Let's call it the 'interleaved conversation' chat paradigm. Am I rembering this correctly? More importantly, is there a modern way of doing this in any of the GUI-based clients? I'm surprised this isn't a common desire/feature because I think it would greatly improve the experience, especially on channels with high SNR. For example, If I'm working on a project I may connect to Freenode and join : #Qt,#OpenGL,#C++. As it is now, with mIRC,Xchat, I have to manually flip between pages just to see whats being said and to reply. What I envision would go more like this (using only 2 channels for simplicity) /join #QT #OpenGL < [QT] QtChannelUser: Hello TwoPixelGrid. < [OpenGL] OpenGLChannelUser: Hi there TwoPixelGrid. @QT: Hi QtChannelUser @OpenGL: Hello againOpenGLChannelUser And this message is going out to all my channels. Do I have to write a new client or is this already out there?

    Read the article

  • Unable to communicate with EWS from Exchange Server

    - by kschieck
    We are currently running a 2 server exchange environment with Edge services on their own. We are in the process of trying to deploy a piece of software that uses the EWS API which has brought me to this form, the software ties into the EWS service and uses it to forward messages (this is failing). Using the software error logs I have found that accessing EWS from the exchange server is not possible. From my work machine and an external address I can type the following https ://webmail.companyname.com/ews/exchange.asmx and be prompted for a username and password, once I enter credentials I get a screen full of information from services.wsdl. The problem is when I try the same URL from the exchange server and get the credentials prompt I cannot get past it. Even with the same credentials that work externally and from my desk it just keeps looping around. Capture from software log (11:41:32.6415 000017e4 System.Net.WebException: The request failed with HTTP status 401: Unauthorized.) I have also found the same results when trying https://webmail.companyname.com/ Autodiscover /Autodiscover.xml . Environment Information Server 2008 STD 64bit Exchange 2007 SP1 Purchased Cert – webmail.companyname.com I have also confirmed that all services have the proper internal and external URL’s. Any help would be appreciated.

    Read the article

  • Postfix Whitelist before recipient restrictions

    - by GruffTech
    Alright. Some background. We have an anti-spam cluster trucking about 2-3 million emails per day, blocking somewhere in the range of 99% of spam email from our end users. The underlying SMTP server is Postfix 2.2.10. The "Frontline defense" before mail gets carted off to SpamAssassin/ClamAV/ ect ect, is attached below. ...basic config.... smtpd_recipient_restrictions = reject_unauth_destination, reject_rbl_client b.barracudacentral.org, reject_rbl_client cbl.abuseat.org, reject_rbl_client bl.mailspike.net, check_policy_service unix:postgrey/socket ...more basic config.... As you can see, standard RBL services from various companies, as well as a Postgrey service. The problem is, I have one client (out of thousands) who is very upset that we blocked an important email of theirs. It was sent through a russian freemailer who was currently blocked in two of our three RBL servers. I explained the situation to them, however they are insisting we do not block any of their emails. So i need a method of whitelisting ANY email that comes to domain.com, however i need it to take place before any of the recipient restrictions, they want no RBL or postgrey blocking at all. I've done a bit of research myself, http://www.howtoforge.com/how-to-whitelist-hosts-ip-addresses-in-postfix seemed to be a good guide at first, almost fixing my problem, But i want it to accept based on TO address, not originating server.

    Read the article

  • Why am I seeing MailSlot Browse messages on unrouted ports of my Linux box?

    - by nmichaels
    I have a Linux box (Debian squeeze) with several NICs. The ones of interest are: eth3 - my main link to the network (dhcp on 10.20.30.0/24) eth0 - the first connection to my test network (static: 192.168.1.2) eth4 - the second connection to my test network (static: 192.168.1.1) My routing table looks like this: $ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.20.30.0 * 255.255.255.0 U 0 0 0 eth3 default 10.20.30.254 0.0.0.0 UG 0 0 0 eth3 I have the 2 test net ports connected to each other with a crossover cable and an instance of wireshark running on each port. Every once in a while, I'll see a packet like the following show up. Who could be doing this, and how do I convince them to stop? I do have Samba running on the machine (for a cifs mount) but don't see why it would be sending packets out to unrouted ports. I had a Windows VM running in VMWare Client and thought that might be causing it, but it still happens without it. What I want is totally silent interfaces so I can run some tests with Scapy over them.

    Read the article

  • GlassFish v3: Security related updates?

    - by chris_l
    I've used GlassFish v3.0 as my main development application server for a few weeks now. Now that I want to install it on my VPS, I'd like to get the latest security updates, because Glassfish v3 Release 3.0 (Open Source Edition or not) is already a few months old, and v3.1 is only available as "early access" nightlies (see https://glassfish.dev.java.net/public/downloadsindex.html). GlassFish offers an update mechanism (via pkg or updateTool), but when I simply try to get the latest updates (pkg image-update), it finds nothing. However, when I change the preferred publisher to dev.glassfish.org, I get a list with lots of updates. The interesting thing is, that I haven't been able to find any description about the exact meaning of the diverse publishers/repositories (release, stable, contrib and dev) anywhere on the web, most importantly answering the question: Am I supposed to use the "dev" repository for security updates, or is it (probably more likely) for unstable updates? Where do I get security updates from then? Or are there simply no security updates yet? Asking on the GlassFish forum resulted in 56 views, but 0 answers.

    Read the article

  • SATA HDD stuttering on reads (LED on)

    - by jdehaan
    I hope I can get some new ideas to solve the issue. What I have: AMD Phenom II X4 905e Box, Sockel AM3 Gigabyte GA-MA790XTA-UD4, AMD 790X, AM3 ATX WD Caviar GreenPower 1,5TB SATA II 4GB Kit OCZ DDR3 PC3-10666 Platinum Low-Voltage CL7 HIS HD 4670 iSilence4 DDR3 1024MB Native HDMI Dual-DVI, PCI-Express Behavior: Everything works normally excepting the HDD accesses. The drive seems to get stuck in reading data (LED drive by Mainboard is on for a while) then recovers and goes on. There is a delay of more than 30s sometimes. Often it is a matter of 5-10s. This does not seem related to the workload of the disk. What I tried so far: Use different SATA port: I switched from the SATA3 to SATA2 then the SATA driven by the CPU, no difference. Turned AHCI off, drove the SATA in IDE mode, same behavior, now I felt like the HDD has problems Deactivated energy saving settings (BeQuiet, ...), disabled 3 CPUs (msconfig) supposing some race condition or trouble with changing freqs, same trouble With Windows7 Professional 64Bit, I installed the hotfix http://support.microsoft.com/?scid=kb%3Ben-us%3B976418&x=8&y=9 with no success. The problem description matches what I experienced, so I felt lucky but was quite in a sad mood after being deceived. Burned the DLG 5.04f DataLifeGuard CD from WD to check the drive. All tests passed, to my surprise! Installed an Ubuntu on the same drive i386 flavour. Drive still in IDE mode, exactly the same behavior. So the OS does not matter. What I did not try yet: http://www.gigabyte.eu/Support/Motherboard/BIOS_Model.aspx?ProductID=3263 I have a F2 BIOS and there is a F3a Beta, did someone have similar issues that were solved by this update? It is a beta so I fear upgrading a bit and I could find no release notes at all on the net, not really serious work maybe they had issues translating from Chinese??? Using another HDD drive Does someone have other hints or a similar issue? Maybe it is neither the HDD nor the Mainboard/BIOS?

    Read the article

  • Wireless Activity Monitoring for PCI DSS Compliance

    - by dkusleika
    In an effort to be PCI DSS compliant, I took a trustkeeper.net questionnaire. I failed the question that asks Is the presence of wireless access points tested for by using a wireless analyzer at least quarterly or by deploying a wireless IDS/IPS to identify all wireless devices in use? (SAQ #11.1) My only wireless access point is outside my firewall, so even if you cracked my wireless you couldn't get inside my domain (unless you crack that too). My firewall doesn't have IPS and I couldn't tell if it had IDS. I looked around for a wireless analyzer, but what I found was $500, which is a little pricey for my size business. And even if I got it, I'm not sure I would understand what it tells me. Surely there are smaller/less sophisticated businesses that take credit cards and have solved this. My questions are: What are the risks if someone were to crack my wireless? (Could they read all internet traffic? Just wireless traffic? Just use my internet connection?) And what is the best/cheapest way to test my connection point quarterly? Should I buy the $500 analyzer? Domain is Windows Server 2000. Firewall is Sonicwall Pro 2040. Router is 8 port D-link.

    Read the article

  • Amazon VPC NAT not working

    - by rpkelly
    I'm trying to create a NAT instance for my VPC to allow instances on private subnets connect to the internet (most importantly, S3). I tried following the instructions here: http://docs.amazonwebservices.com/AmazonVPC/2011-07-15/UserGuide/index.html?VPC_NAT_Instance.html . Unfortunately, the instances in the private subnet (call it 10.10.2.0/24) cannot reach the internet. I have done the following: Create a NAT instance (Amazon's ami-vpc-nat-1.0.0-beta.i386-ebs (ami-d8699bb1)) in public subnet (call it 10.10.1.0/24). Changed "Source / Dest Check" to disabled. Created a new entry in the default routing table (which is used by 10.10.2.0/24) and had it point to the ID of the newly created instance. Associated an Elastic IP address with the NAT instance. Allowed all outbound traffic on the security group of the NAT instance. Ensured that all traffic could pass between the two subnets. I've tried also doing this with an existing instance using iptables, but had no luck. And I have verified that sys.net.ipv4.ip_forward is 1, just in case anyone was wondering. And I still have no internet connectivity from the instances on 10.10.2.0/24. Does anyone have any suggestions?

    Read the article

  • How to restrict postfix send limited email with policyd v2?

    - by Shalini Tripathi
    I have installed cluebringer-2.0.7 for postfix and enabled below lines in the main.cf file of postfix. But I could not see any policy working smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination check_policy_service inet:127.0.0.1:10031 smtpd_end_of_data_restrictions=check_policy_service inet:127.0.0.1:10031 To check further I enabled logging in policyd and its only shows below logs and there is no logs getting populated when I send new emails.. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Process Backgrounded [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Policyd v2 / Cluebringer - v2.0.7 [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Initializing system modules. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: System modules initialized. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load started... [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = AccessControl: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckHelo: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckSPF: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Greylisting: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Quotas: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Postfix): enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Bizanga): enabled [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load done. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: 2012/06/12-21:18:50 cbp (type Net::Server::PreFork) starting! pid(13949) [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Binding to TCP port 10031 on host * [2012/06/12-21:18:50 - 13949] [CORE] WARNING: Group Not Defined. Defaulting to EGID '0 10 6 4 3 2 1 0' [2012/06/12-21:18:50 - 13949] [CORE] WARNING: User Not Defined. Defaulting to EUID '0' Do I need to do anymore settings for postfix to listen on policyd???Please help

    Read the article

  • network policy + WPA enterprise (tkip) Windows 2008 R2

    - by Aceth
    hi I've attempted the following guide and in a bit of a pickle. http://techblog.mirabito.net.au/?p=87 My main goal is to have a username / password based wireless authentication with active directory integration. I keep getting the error Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\rhysbeta Account Name: rhysbeta Account Domain: domain Fully Qualified Account Name: domain\rhysbeta Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 00-12-BF-00-71-3C:wirelessname Calling Station Identifier: 00-23-76-5D-1E-31 NAS: NAS IPv4 Address: 0.0.0.0 NAS IPv6 Address: - NAS Identifier: - NAS Port-Type: Wireless - IEEE 802.11 NAS Port: 2 RADIUS Client: Client Friendly Name: Belkin54g Client IP Address: x.x.x.10 Authentication Details: Connection Request Policy Name: Secure Wireless Connections Network Policy Name: Secure Wireless Connections Authentication Provider: Windows Authentication Server: srvr.example.com Authentication Type: EAP EAP Type: - Account Session Identifier: - Logging Results: Accounting information was written to the local log file. Reason Code: 22 Reason: The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server. ` I would love to have it so that non domain devices

    Read the article

  • Trying to setup catchall mail forwarding on my rackspace's cloudspace server

    - by bob_cobb
    I'm running Ubuntu 12 Precise Pangolin and am trying to configure my server to catchall mail sent to it and forward it to my gmail address. I've been trying lots of examples online like editing my main.cf file which looks like this: smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = destiny alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = destiny, localhost.localdomain, localhost relayhost = smtp.sendgrid.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 51200000 recipient_delimiter = + inet_interfaces = all inet_protocols = all In my /etc/postfix/virtual I have: @mydomain.com [email protected] @myotherdomain.com [email protected] Which isn't working when I email [email protected] or [email protected]. So I got the recommendation to add the following to my /etc/alias: postmaster:root root:[email protected] restarted postfix, and tried emailing [email protected] or [email protected] but it still won't send. Does anyone have any idea what I'm doing wrong here? I'd appreciate any help.

    Read the article

  • Windows 8, IIS8 how to make PHP imagick work

    - by Laci K
    I'm new to IIS server before IIS for 6 years I used Apache 2.X and with Apache imageMagick and its PHP module imagick worked just fine even with x64 version of PHP and Apache 2.4 and imageMagick. I tried to make imagick to work with IIS8 but it wont work. I always get the typical PHP startup warning in my log PHP Startup: Unable to load dynamic library 'C:\Program Files (x86)\iis express\PHP\v5.4\ext\php_imagick.dll' - %1 is not a valid Win32 application. in Unknown on line 0 And the next thing why is IIS loading php from IIS express folder if I have php in the program files? But actually I dont care until it works :) So what I did so far I unistalled imageMagick 6.7.X 64bit version and installed the latest x86 version, tested it in command line and it worked, than I looked up on net the latest imagick DLL which was I think the 3.1.0RC2 (founded here http://www.peewit.fr/imagick/) than I copied the dll to PHP's ext folder than edited php.ini and added the imagick to the dynamic extensions after that I restarted IIS and than nothing :( I got the error which I wrote earlier. Today I installed PEAR package Installer because I read somewhere that someone made it work with it but he also mentioned, that he needed to comply wincache too. Isn't there any easier solutions to make it work? Could someone maybe write me a step by step guide how to make this work.

    Read the article

  • How to setup Mac server to use two gateways

    - by Brady
    I recently asked this question: How to set Mac server to use different Gateway for internet bound traffic The answer given works but has presented me with another issue that I didnt make clear in that question. Here is my network layout as it stands: At the moment outside staff members use some services on the existing internet 1 link. Those services are hosted by the Mac server. If I change the gateway of the Mac server to the second modem those outside staff lose visabilty on those services. Now I dont know how to go about solving this issue. I want the second link to be used when the Mac server goes to rsync data offsite but everything else use link one. How do I do this? Thanks Scott EDIT: This has been resolved by setting the default gateway on the Mac server to 192.168.1.254 Thus leaving everything on the network as it was before. but to get the Mac server to use the other link for rsync I've added a route to the Mac server to route traffic to the rsync server through the second gateway. sudo route add -net {server IP's}/{Netmask} 192.168.1.1 I've awarded the answer to gravyface for pointing me to a post on how to make this route persistant in Mac

    Read the article

  • The RTL8111/8168B NIC under Linux and the r8168 driver

    - by nik
    So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

    Read the article

  • arp requests are sent continuously and my linux machine disconnected to the world

    - by sees
    I have the following problem and really need your help I'm implementing a small server to receive request from client on port 18999(just sample) using TCP socket. When I tested my server by using a lot of requests from a tablet through a router, I got the ARP problem(?) My net work just like: TABLET <------- WIRELESS ROUTER <------- MY SERVER (LINUX) Problems: 1. Can not connect to my Linux any more ( telnet, ping v.v...unreachable) 2. I use serial cable to connect to my Linux machine and use Wiresharp (from Windows) to catch the send message from Linux. It says that Linux keeps sending out continuously every 3 seconds ARP messages like the following: xx:xx:99:77:ff:69 ff:ff:ff:ff:ff:ff ARP 60 Who has 192.168.10.2? Tell 192.168.10.3 In the above message: xx:xx:99:77:ff:69 my Linux MAC address 192.168.10.2 my Tablet address 192.168.10.3 my Linux IP address Can you help me figure out the problem? Or tell me the way to detect the problem and reset the network back to normal (maybe restart Linux but I want to detect problem and restart automatically) UPDATE: 1. The above network works normally if tablet sends messages to my LINUX in normal speed (but also down after 48 hours) 2. The router works again after I unplugged my Linux ethernet cable (RJ45) from router. 3. The wireless network still works ( I can browser the router page from tablet) 4. When I use: ifconfig down then ifconfig up , the Linux restarts (?????????)

    Read the article

  • Why are group policy preference drive mappings not applied to the domain administrator account?

    - by Saariko
    I have a working policy on my entire domain. I just found out, when logging with the domain administrator, that this policy is not applied (EDIT: Running : gpresult shows that the GPO's are applied - but, this GPO is for Drive Mappings, and the actual drive mappings are NOT shown) The administrator account - does not have any login script on his profile tab. To note: The mappings were applied before the GPO with a login script using the : net use ... command - all was working perfectly and correctly for the domain administrator user as well - That removes sharing and security problem (IMO) My GPO's are mainly small/atomic settings: single GPO to handle each settings: UAC, Firewall, printers. GPO status for the object is enabled That's an overview of the Drive Maps: Reading on MS support site, I checked the delegation tab, and it is marked as applied to domain and enterprise admins. Every user gets these policies correctly. The OU that is set is the root of the domain. (for testing purpose - I did that to eliminate hierarchy issues - did not help) Block Inheritance is disabled. (never used it anyway) GPO link GPO Security Filterings

    Read the article

  • Apache2 Manage Server default

    - by Jaime E. Valdez
    I'm trying to setup two domains correctly. I have some issues I hope you can help me. Site one's conf: <VirtualHost myipaddress:80> ServerName www.domain1.com ServerAdmin [email protected] DocumentRoot /home/domain1/public_html </VirtualHost> My other domain conf is: <VirtualHost myipaddress:80> ServerName www.domain2.com ServerAlias *.domain2.com domain2.com ServerAdmin [email protected] DocumentRoot /home/domain2/public_html </VirtualHost> The default site is disabled. The problem is that when accessing "domain2.com" from my browser, it always redirects to "www.domain1.com". It only works when I excplicitly access "www.domain2.com". I have also other domains like "domain1.net", "domain1.info" pointing to my server but at this moment are not configured either setup on Apache yet I can access from browser and always accessing to "www.domain1.com". By the way is there any possible configuration over Apache to handle IP only, I mean if I type "http://myipaddress/" I get the "www.domain1.com"... Arrgh.

    Read the article

  • Postfix / Dovecot email setup not storing email

    - by Nick Duffell
    I'm trying to setup postfix / dovecot on my debian server to use it for a mail server. I set everything up according to a tutorial on the net, and it all seemed OK. I can send emails from it, so SMTP is not a problem, however I cannot receive emails. Looking into the files in /home/nick/mail/ I can see that if I send an email to myself (from the server, to itself) the emails are there, but are put straight into the Deleted Messages folder. I don't know why this is. When I send an email from another mail account (not on this server), the emails are nowhere to be found. Also, looking at the log file /var/log/mail.log all seems to be OK, I get the following when I receive an email, which looks OK to me: Nov 7 22:47:22 nickduffell postfix/local[17825]: 05B1173581A6: to=, relay=local, delay=0.37, delays=0.31/0.02/0/0.03, dsn=2.0.0, status=sent (delivered to mailbox) Any ideas? Thanks EDIT: I should also add that although the emails I send myself are in the Deleted Messages folder, and in my mail client I can see that "Trash" has 3 items, I cannot download them in my mail client...

    Read the article

  • printing parallel over ethernet cable

    - by Crudler
    I have a bit of an interesting challenge :) I have a machine with a parallel printer output, i want it to be able to print instead to a printer in a different room and i know that parallel isnt great over big distances. i found this: http://www.amazon.com/over-Cat5-Extension-Cable-Adapter/dp/B002WJ9S6Y%3FSubscriptionId%3DAKIAINHICTCYYZGJWT4Q%26tag%3Dusbprintercables.net-20%26linkCode%3Dxm2%26camp%3D2025%26creative%3D165953%26creativeASIN%3DB002WJ9S6Y which will let me connect over cat5, but its usb to cat 5. my machine can only output on parallel (its not a computer) so what i was thinking of getting is a parallel(f) to usb and usb to parallel (M) for either side i.e. machine - parallel - usb - cat5 - usb - parallel -printer just seems a bit messy :) suggestions? another thing i would like to try is to get rid of the old school parallel printer and instead use a network based multi function. would this be possible? i.e. machine - parallel -usb - cat5 - ethernet print server - network printer this might be rougher because the machine cannot "know" that we are using a network printer. it can ONLY print to LPT1 Thanks!

    Read the article

  • How do you setup FTP with IIS Manager Users in an NLB environment with shared IIS configs?

    - by William Jens
    I've setup a 2 node NLB cluster and used the following to share IIS configs between them. http://blogs.technet.com/b/meamcs/archive/2012/05/30/configuring-iis-7-5-shared-configuration.aspx The IIS configs and content is located on a network share via a UNC path. This works - updating IIS settings on one node, is visible in another node and my website works on the individual nodes and the cluster as whole. I'm able to setup an FTP site and successfully connect with my Windows login. However, I want to use IIS Manager Authentication as defined in: http://www.iis.net/learn/publish/using-the-ftp-service/configure-ftp-with-iis-manager-authentication-in-iis-7 I've tried using "Network Service" with the FTP COM object as well as a dedicated user account that exists on all three hosts, but every time I try to login with an IIS user I get something like the following: IISWMSVC_AUTHENTICATION_UNABLE_TO_READ_CONFIG An unexpected error occurred while retrieving the authentication information. Exception:System.Runtime.InteropServices.COMException (0x8007052E): Filename: Error: at Microsoft.Web.Administration.Interop.AppHostWritableAdminManager.GetAdminSection(String bstrSectionName, String bstrSectionPath) at Microsoft.Web.Administration.Configuration.GetSectionInternal(ConfigurationSection section, String sectionPath, String locationPath) at Microsoft.Web.Management.Server.ConfigurationAuthenticationProvider.GetSection(ServerManager serverManager) Process:dllhost User=NT AUTHORITY\NETWORK SERVICE Can anyone point me in the right direction here?

    Read the article

  • Filezilla client unable to get directory listing from Filezilla Server (Windows)

    - by sestocker
    I've set up a self signed certificate in FileZilla server and enabled FTP over SSL/TPS. When I connect from the client FileZilla, I am able to authenticate but cannot get a directory listing: Status: Connecting to MY_SERVER_IP:21... Status: Connection established, waiting for welcome message... Response: 220-FileZilla Server version 0.9.39 beta Response: 220-written by Tim Kosse ([email protected]) Response: 220 Please visit http://sourceforge.net/projects/filezilla/ Command: AUTH TLS Response: 234 Using authentication type TLS Status: Initializing TLS... Status: Verifying certificate... Command: USER MYUSER Status: TLS/SSL connection established. Response: 331 Password required for MYUSER Command: PASS ******** Response: 230 Logged on Command: PBSZ 0 Response: 200 PBSZ=0 Command: PROT P Response: 200 Protection level set to P Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I Command: PORT 10,10,25,85,219,172 Response: 200 Port command successful Command: MLSD Response: 150 Opening data channel for directory list. Response: 425 Can't open data connection. Error: Failed to retrieve directory listing I have ports 21 and 50001 through 50005 open on the firewall. We are migrating servers - the 50001 - 50005 is one of the things that helped get FTPS working on the old server. I'm not sure this installation would use the same ports? What else could be the problem?

    Read the article

< Previous Page | 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048  | Next Page >