git update server info - Page 2079

Difference between `curl -I` and `curl -X HEAD`

- by chmeee

I was wathcing the funny server type from http://www.reddit.com with curl -I http://www.reddit.com when I guessed that curl -X HEAD http://www.reddit.com would do the same. But, in fact, it doesn't. I'm curious about why. This is what I observe running the two commands: curl -I: works as expected, outputs the header and exists. curl -X HEAD: does not show anything and seems to wait for user input. But, sniffing with tshark I see the second command actually sends the same HTML query and receives the correct answer, but it does not show it and it doesn't close the connection. curl -I 0.000000 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=47267342 TSER=0 WS=6 0.045392 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1460 TSV=2552532839 TSER=47267342 WS=1 0.045441 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=1 Ack=1 Win=5888 Len=0 TSV=47267353 TSER=2552532839 0.045623 333.33.33.33 -> 213.248.111.106 HTTP HEAD / HTTP/1.1 0.091665 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=2552532886 TSER=47267353 0.861782 213.248.111.106 -> 333.33.33.33 HTTP HTTP/1.1 200 OK 0.861830 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47267557 TSER=2552533656 0.862127 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [FIN, ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47267557 TSER=2552533656 0.910810 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [FIN, ACK] Seq=321 Ack=156 Win=6432 Len=0 TSV=2552533705 TSER=47267557 0.910880 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=156 Ack=322 Win=6912 Len=0 TSV=47267570 TSER=2552533705 curl -X HEAD 34.106389 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=47275868 TSER=0 WS=6 34.149507 213.248.111.90 -> 333.33.33.33 TCP http > 51690 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1460 TSV=3920268348 TSER=47275868 WS=1 34.149560 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [ACK] Seq=1 Ack=1 Win=5888 Len=0 TSV=47275879 TSER=3920268348 34.149646 333.33.33.33 -> 213.248.111.90 HTTP HEAD / HTTP/1.1 34.191484 213.248.111.90 -> 333.33.33.33 TCP http > 51690 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=3920268390 TSER=47275879 34.192657 213.248.111.90 -> 333.33.33.33 TCP [TCP Dup ACK 15#1] http > 51690 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=3920268390 TSER=47275879 34.823399 213.248.111.90 -> 333.33.33.33 HTTP HTTP/1.1 200 OK 34.823453 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47276048 TSER=3920269022 Any idea about why this difference in behaviour?

Read the article

Connection Timed Out - Simple outbound Postfix for PHP Contact form

- by BLaZuRE

Alright, so I only got Postfix for a PHP contact form that will send email to a single . I only want it to send out mail to a single external address ([email protected]). I have domain sub1.sub2.domain.com. I installed Postfix out of the Ubuntu repo, with minimal config changes. I cannot get Postfix to send mail externally (though it succeeds for internal accounts, which is unnecessary). The email simply defers if I generate an email using PHP mail(). If I try to form my own in telnet, right after rcpt to: [email][email protected][/email], I get a postfix/smtpd[31606]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 550 5.1.1 <[email protected]>: Recipient address rejected: example.com; from=<root@localhost> to=<[email protected]> proto=ESMTP helo=<localhost> when commenting out default_transport = error and relay_transport = error lines, I get the following: Jun 26 14:33:00 sub1 postfix/smtp[12191]: 2DA06F88206A: to=<[email protected]>, relay=none, delay=514, delays=409/0.01/105/0, dsn=4.4.1, status=deferred (connect to aspmx3.googlemail.com[74.125.127.27]:25: Connection timed out) Jun 26 14:36:36 sub1 postfix/smtp[12225]: connect to mta7.am0.yahoodns.net[98.139.175.224]:25: Connection timed out Jun 26 14:38:00 sub1 postfix/smtp[12225]: 22952F88208E: to=<[email protected]>, relay=none, delay=655, delays=550/0.01/105/0, dsn=4.4.1, status=deferred (connect to mta5.am0.yahoodns.net[67.195.168.230]:25: Connection timed out) My main.cf # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = sub1.sub2.domain.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = sub1.sub2.domain.com, localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all default_transport = error relay_transport = error Also, a dig sub1.sub2.domain.com MX returns: ; <<>> DiG 9.7.0-P1 <<>> sub1.sub2.domain.com MX ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 4853 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 1, ADDITIONAL: 0 ;; QUESTION SECTION: ;sub1.sub2.domain.com. IN MX ;; AUTHORITY SECTION: sub2.domain.com. 600 IN SOA sub2.domain.com. sub5.domain.com. 2012062915 7200 600 1209600 600 ;; Query time: 0 msec ;; SERVER: x.x.x.x#53(x.x.x.x) ;; WHEN: Fri Jun 29 16:35:00 2012 ;; MSG SIZE rcvd: 84 lsof -i returns empty netstat -t -a | grep LISTEN returns tcp 0 0 localhost:mysql *:* LISTEN tcp 0 0 *:ftp *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 localhost:ipp *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp6 0 0 [::]:netbios-ssn [::]:* LISTEN tcp6 0 0 [::]:www [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 localhost:ipp [::]:* LISTEN tcp6 0 0 [::]:microsoft-ds [::]:* LISTEN

Read the article

KVM + Cloudmin + IpTables

- by Alex

I have a KVM virtualization on a machine. I use Ubuntu Server + Cloudmin (in order to manage virtual machine instances). On a host system I have four network interfaces: ebadmin@saturn:/var/log$ ifconfig br0 Link encap:Ethernet HWaddr 10:78:d2:ec:16:38 inet addr:192.168.0.253 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::1278:d2ff:feec:1638/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:589337 errors:0 dropped:0 overruns:0 frame:0 TX packets:334357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:753652448 (753.6 MB) TX bytes:43385198 (43.3 MB) br1 Link encap:Ethernet HWaddr 6e:a4:06:39:26:60 inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::6ca4:6ff:fe39:2660/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16995 errors:0 dropped:0 overruns:0 frame:0 TX packets:13309 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2059264 (2.0 MB) TX bytes:1763980 (1.7 MB) eth0 Link encap:Ethernet HWaddr 10:78:d2:ec:16:38 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:610558 errors:0 dropped:0 overruns:0 frame:0 TX packets:332382 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:769477564 (769.4 MB) TX bytes:44360402 (44.3 MB) Interrupt:20 Memory:fe400000-fe420000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:239632 errors:0 dropped:0 overruns:0 frame:0 TX packets:239632 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50738052 (50.7 MB) TX bytes:50738052 (50.7 MB) tap0 Link encap:Ethernet HWaddr 6e:a4:06:39:26:60 inet6 addr: fe80::6ca4:6ff:fe39:2660/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17821 errors:0 dropped:0 overruns:0 frame:0 TX packets:13703 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:2370468 (2.3 MB) TX bytes:1782356 (1.7 MB) br0 is connected to a real network, br1 is used to create a private network shared between guest systems. Now I need to configure iptables for network access. First of all I allow ssh sessions on port 8022 on the host system, then I allow all connections in state RELATED, ESTABLISHED. This is working ok. I install another system as guest, it's IP address is 192.168.10.2, and now I have two problems: I want to allow the access from this host to the outside world, cannot accomplish this. I can ssh from the host. I want to be able to ssh to the guest from the outside world using 8023 port. Cannot accomplish this. Full iptables configuration is following: ebadmin@saturn:/var/log$ sudo iptables --list [sudo] password for ebadmin: Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere tcp dpt:8022 ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED LOG all -- anywhere anywhere LOG level warning Chain FORWARD (policy ACCEPT) target prot opt source destination LOG all -- anywhere anywhere LOG level warning Chain OUTPUT (policy ACCEPT) target prot opt source destination LOG all -- anywhere anywhere LOG level warning ebadmin@saturn:/var/log$ sudo iptables -t nat --list Chain PREROUTING (policy ACCEPT) target prot opt source destination DNAT tcp -- anywhere anywhere tcp spt:8023 to:192.168.10.2:22 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination The worst of all is that I don't know how to interpret iptables logs. I don't see the final decision of the firewall. Need help urgently.

Read the article

In Exim, is RBL spam rejected prior to being scanned by SpamAssassin?

- by user955664

I've recently been battling spam issues on our mail server. One account in particular was getting hammered with incoming spam. SpamAssassin's memory use is one of our concerns. What I've done is enable RBLs in Exim. I now see many rejection notices in the Exim log based on the various RBLs, which is good. However, when I run Eximstats, the numbers seem to be the same as they were prior to the enabling of the RBLs. I am assuming because the email is still logged in some way prior to the rejection. Is that what's happening, or am I missing something else? Does anyone know if these emails are rejected prior to being processed by SpamAssassin? Or does anyone know how I'd be able to find out? Is there a standard way to generate SpamAssassin stats, similar to Eximstats, so that I could compare the numbers? Thank you for your time and any advice. Edit: Here is the ACL section of my Exim configuration file ###################################################################### # ACLs # ###################################################################### begin acl # ACL that is used after the RCPT command check_recipient: # to block certain wellknown exploits, Deny for local domains if # local parts begin with a dot or contain @ % ! / | deny domains = +local_domains local_parts = ^[.] : ^.*[@%!/|] # to restrict port 587 to authenticated users only # see also daemon_smtp_ports above accept hosts = +auth_relay_hosts condition = ${if eq {$interface_port}{587} {yes}{no}} endpass message = relay not permitted, authentication required authenticated = * # allow local users to send outgoing messages using slashes # and vertical bars in their local parts. # Block outgoing local parts that begin with a dot, slash, or vertical # bar but allows them within the local part. # The sequence \..\ is barred. The usage of @ % and ! is barred as # before. The motivation is to prevent your users (or their virii) # from mounting certain kinds of attacks on remote sites. deny domains = !+local_domains local_parts = ^[./|] : ^.*[@%!] : ^.*/\\.\\./ # local source whitelist # accept if the source is local SMTP (i.e. not over TCP/IP). # Test for this by testing for an empty sending host field. accept hosts = : # sender domains whitelist # accept if sender domain is in whitelist accept sender_domains = +whitelist_domains # sender hosts whitelist # accept if sender host is in whitelist accept hosts = +whitelist_hosts accept hosts = +whitelist_hosts_ip # envelope senders whitelist # accept if envelope sender is in whitelist accept senders = +whitelist_senders # accept mail to postmaster in any local domain, regardless of source accept local_parts = postmaster domains = +local_domains # accept mail to abuse in any local domain, regardless of source accept local_parts = abuse domains = +local_domains # accept mail to hostmaster in any local domain, regardless of source accept local_parts = hostmaster domains =+local_domains # OPTIONAL MODIFICATIONS: # If the page you're using to notify senders of blocked email of how # to get their address unblocked will use a web form to send you email so # you'll know to unblock those senders, then you may leave these lines # commented out. However, if you'll be telling your senders of blocked # email to send an email to [email protected], then you should # replace "errors" with the left side of the email address you'll be # using, and "example.com" with the right side of the email address and # then uncomment the second two lines, leaving the first one commented. # Doing this will mean anyone can send email to this specific address, # even if they're at a blocked domain, and even if your domain is using # blocklists. # accept mail to [email protected], regardless of source # accept local_parts = errors # domains = example.com # deny so-called "legal" spammers" deny message = Email blocked by LBL - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains sender_domains = +blacklist_domains # deny using hostname in bad_sender_hosts blacklist deny message = Email blocked by BSHL - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains hosts = +bad_sender_hosts # deny using IP in bad_sender_hosts blacklist deny message = Email blocked by BSHL - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains hosts = +bad_sender_hosts_ip # deny using email address in blacklist_senders deny message = Email blocked by BSAL - to unblock see http://www.example.com/ domains = +use_rbl_domains senders = +blacklist_senders # By default we do NOT require sender verification. # Sender verification denies unless sender address can be verified: # If you want to require sender verification, i.e., that the sending # address is routable and mail can be delivered to it, then # uncomment the next line. If you do not want to require sender # verification, leave the line commented out #require verify = sender # deny using .spamhaus deny message = Email blocked by SPAMHAUS - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains dnslists = sbl.spamhaus.org # deny using ordb # deny message = Email blocked by ORDB - to unblock see http://www.example.com/ # # only for domains that do want to be tested against RBLs # domains = +use_rbl_domains # dnslists = relays.ordb.org # deny using sorbs smtp list deny message = Email blocked by SORBS - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains dnslists = dnsbl.sorbs.net=127.0.0.5 # Next deny stuff from more "fuzzy" blacklists # but do bypass all checking for whitelisted host names # and for authenticated users # deny using spamcop deny message = Email blocked by SPAMCOP - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = bl.spamcop.net # deny using njabl deny message = Email blocked by NJABL - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = dnsbl.njabl.org # deny using cbl deny message = Email blocked by CBL - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = cbl.abuseat.org # deny using all other sorbs ip-based blocklist besides smtp list deny message = Email blocked by SORBS - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = dnsbl.sorbs.net!=127.0.0.6 # deny using sorbs name based list deny message = Email blocked by SORBS - to unblock see http://www.example.com/ domains =+use_rbl_domains # rhsbl list is name based dnslists = rhsbl.sorbs.net/$sender_address_domain # accept if address is in a local domain as long as recipient can be verified accept domains = +local_domains endpass message = "Unknown User" verify = recipient # accept if address is in a domain for which we relay as long as recipient # can be verified accept domains = +relay_domains endpass verify=recipient # accept if message comes for a host for which we are an outgoing relay # recipient verification is omitted because many MUA clients don't cope # well with SMTP error responses. If you are actually relaying from MTAs # then you should probably add recipient verify here accept hosts = +relay_hosts accept hosts = +auth_relay_hosts endpass message = authentication required authenticated = * deny message = relay not permitted # default at end of acl causes a "deny", but line below will give # an explicit error message: deny message = relay not permitted # ACL that is used after the DATA command check_message: accept

Read the article

Automatically starting svnserve on Snow Leopard

- by Cleggy

I have installed Subversion onto my iMac running Snow Leopard, but am having trouble getting svnserve to start up automatically. As I understand it (I'm still fairly green with OSX), the best way to do that is to utilize launchd. To that end, I have created the following .plist file in the /Library/LaunchDaemons folder. If I use launchctl to execute this file, svnserve starts as expected, but it doesn't automatically start when the system starts up or I log in. <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Disabled</key> <false/> <key>Label</key> <string>org.tigris.subversion.svnserve</string> <key>UserName</key> <string>Dave</string> <key>ProgramArguments</key> <array> <string>/opt/subversion/bin/svnserve</string> <string>--inetd</string> <string>--root=/Users/Shared/SVNrep</string> </array> <key>ServiceDescription</key> <string>Subversion Standalone Server</string> <key>Sockets</key> <dict> <key>Listeners</key> <array> <dict> <key>SockFamily</key> <string>IPv4</string> <key>SockServiceName</key> <string>svn</string> <key>SockType</key> <string>stream</string> </dict> <dict> <key>SockFamily</key> <string>IPv6</string> <key>SockServiceName</key> <string>svn</string> <key>SockType</key> <string>stream</string> </dict> </array> </dict> <key>inetdCompatibility</key> <dict> <key>Wait</key> <false/> </dict> </dict> </plist> If anyone here could provide any suggestions as to how to get this to work, I'd really appreciate it.

Read the article

Do email forms need to be santized before sending?

- by levi

I have a client that keeps getting reports from godaddy's "websiteprotection.com" stating how the website is insecure. Your website contains pages that do not properly sanitize visitor-provided input to make sure it contains no malicious content or scripts. Cross-site scripting vulnerabilities let malicious users execute arbitrary HTML or script code in another visitor's browser. Output: The request string used to detect this flaw was : /cross_site_scripting.?nasl.asp The output was : HTTP/1.1 404 Not Found\r Date: Wed, 21 Mar 2012 08:12:02 GMT\r Server: Apache\r X-Pingback:http://?CLIENTSWEBSITE.com/?xmlrpc.php\r Expires: Wed, 11 Jan 1984 05:00:00 GMT\r Cache-Control: no-cache, must-revalidate, max-age=0\r Pragma: no-cache\r Set-Cookie: PHPSESSID=?1jsnhuflvd59nb4trtquston50; path=/\r Last-Modified: Wed, 21 Mar 2012 08:12:02 GMT\r Keep-Alive: timeout=15, max=100\r Connection: Keep-Alive\r Transfer-Encoding: chunked\r Content-Type: text/html; charset=UTF-8\r \r <div id="contact-form" class="widget"><form action="http://?CLIENTSWEBSITE.c om/<script>cross_site_?scripting.nasl</script>.asp" id="contactForm" meth od="post"> It looks like it has an issue with the contact form. All the contact form does is posts an ajax request to the same page, and than a PHP script mails the data (no database stuff). Is there any a security issues here? Any ideas on how I can satisfy the security scanner? Here is the form and script: <form action="<?php echo $this->getCurrentUrl(); ?>" id="contactForm" method="post"> <input type="text" name="Name" id="Name" value="" class="txt requiredField name" /> //Some more text inputs <input type="hidden" name="sendadd" id="sendadd" value="<?php echo $emailadd ; ?>" /> <input type="hidden" name="submitted" id="submitted" value="true" /><input class="submit" type="submit" value="Send" /> </form> // Some initial JS validation, if that passes an ajax post is made to the script below //If the form is submitted if(isset($_POST['submitted'])) { //Check captcha if (isset($_POST["captchaPrefix"])) { $capt = new ReallySimpleCaptcha(); $correct = $capt->check( $_POST["captchaPrefix"], $_POST["Captcha"] ); if( ! $correct ) { echo false; die(); } else { $capt->remove( $_POST["captchaPrefix"] ); } } $dateon = $_POST["dateon"]; $ToEmail = $_POST["sendadd"]; $EmailSubject = 'Contact Form Submission from ' . get_bloginfo('title'); $mailheader = "From: ".$_POST["Email"]."\r\n"; $mailheader .= "Reply-To: ".$_POST["Email"]."\r\n"; $mailheader .= "Content-type: text/html; charset=iso-8859-1\r\n"; $MESSAGE_BODY = "Name: ".$_POST["Name"]."<br>"; $MESSAGE_BODY .= "Email Address: ".$_POST["Email"]."<br>"; $MESSAGE_BODY .= "Phone: ".$_POST["Phone"]."<br>"; if ($dateon == "on") {$MESSAGE_BODY .= "Date: ".$_POST["Date"]."<br>";} $MESSAGE_BODY .= "Message: ".$_POST["Comments"]."<br>"; mail($ToEmail, $EmailSubject, $MESSAGE_BODY, $mailheader) or die ("Failure"); echo true; die(); }

Read the article

Rewriting Apache URLs to use only paths and set response headers

- by jabley

I have apache httpd in front of an application running in Tomcat. The application exposes URLs of the form: /path/to/images?id={an-image-id} The entities returned by such URLs are images (even though URIs are opaque, I find human-friendly ones are easier to work with!). The application does not set caching directives on the image response, so I've added that via Apache. # LocationMatch to set caching directives on image responses <LocationMatch "^/path/to/images$"> # Can't have Set-Cookie on response, otherwise the downstream caching proxy # won't cache! Header unset Set-Cookie # Mark the response as cacheable. Header append Cache-Control "max-age=8640000" </LocationMatch> Note that I can't use ExpiresByType since not all images served by the app have versioned URIs. I know that ones served by the /path/to/images resource handler are versioned URIs though, which don't perform any sort of content negotiation, and thus are ripe for Far Future Expires management. This is working well for us. Now a requirement has come up to put something else in front of the app (in this case, Amazon CloudFront) to further distribute and cache some of the content. Amazon CloudFront will not pass query string parameters through to my origin server. I thought I would be able to work around this, by changing my apache config appropriately: # Rewrite to map new Amazon CloudFront friendly URIs to the application resources RewriteRule ^/new/path/to/images/([0-9]+) /path/to/images?id=$1 [PT] # LocationMatch to set caching directives on image responses <LocationMatch "^/path/to/images$"> # Can't have Set-Cookie on response, otherwise the downstream caching proxy # won't cache! Header unset Set-Cookie # Mark the response as cacheable. Header append Cache-Control "max-age=8640000" </LocationMatch> This works fine in terms of serving the content, but there are no longer caching directives with the response. I've tried playing around with [PT], [P] for the RewriteRule, and adding a new LocationMatch directive: # Rewrite to map new Amazon CloudFront friendly URIs to the application resources # /new/path/to/images/12345 -> /path/to/images?id=12345 RewriteRule ^/new/path/to/images/([0-9]+) /path/to/images?id=$1 [PT] # LocationMatch to set caching directives on image responses <LocationMatch "^/path/to/images$"> # Can't have Set-Cookie on response, otherwise the downstream caching proxy # won't cache! Header unset Set-Cookie # Mark the response as cacheable. Header append Cache-Control "max-age=8640000" </LocationMatch> <LocationMatch "^/new/path/to/images/"> # Can't have Set-Cookie on response, otherwise the downstream caching proxy # won't cache! Header unset Set-Cookie # Mark the response as cacheable. Header append Cache-Control "max-age=8640000" </LocationMatch> Unfortunately, I'm still unable to get the Cache-Control header added to the response with the new URL format. Please point out what I'm missing to get /new/path/to/images/12345 returning a 200 response with a Cache-Control: max-age=8640000 header. Pointers as to how to debug apache like this would be appreciated as well!

Read the article

Is it possible to write C# code as below and send email using network in different country?

- by kedar karthik

Is it possible to write C# code as below and send email using mnetwork in different country? MSExchangeWebServiceURL = mail.something.com/ews/exchange.asmx its a web service URL ... sorry to correct my self //....this works great when i run the same code from home network, my friends home network ... anywhere around ... but when i run it from my clients location in columbia ... it fails I have a valid user name and password on that exchange server. Is there any configuration that I can set to achieve this? BTW this code below works when I run it within office network and any network within any home network ... i have tried atleast 5 friends network in Plano, Texas. I want this code to work when run from any network in another country. My client in columbia can connect to web service using a browser .. use the same user name and password ..... but when i run the code above ... it is not able to connect to our web service .... String cMSExchangeWebServiceURL = (String)System.Configuration.ConfigurationSettings.AppSettings["MSExchangeWebServiceURL"]; String cEmail = (String)System.Configuration.ConfigurationSettings.AppSettings["Cemail"]; String cPassword = (String)System.Configuration.ConfigurationSettings.AppSettings["Cpassword"]; String cTo = (String)System.Configuration.ConfigurationSettings.AppSettings["CTo"]; ExchangeServiceBinding esb = new ExchangeServiceBinding(); esb.Timeout = 1800000; esb.AllowAutoRedirect = true; esb.UseDefaultCredentials = false; esb.Credentials = new NetworkCredential(cEmail, cPassword); esb.Url = cMSExchangeWebServiceURL; ServicePointManager.ServerCertificateValidationCallback += delegate(object sender1, X509Certificate certificate, X509Chain chain, SslPolicyErrors sslPolicyErrors) { return true; }; // Create a CreateItem request object CreateItemType request = new CreateItemType(); // Setup the request: // Indicate that we only want to send the message. No copy will be saved. request.MessageDisposition = MessageDispositionType.SendOnly; request.MessageDispositionSpecified = true; // Create a message object and set its properties MessageType message = new MessageType(); message.Subject = subject; message.Body = new TestOutgoingEmailServer.com.cogniti.mail1.BodyType(); message.Body.BodyType1 = BodyTypeType.HTML; message.Body.Value = body; message.ToRecipients = new EmailAddressType[3]; message.ToRecipients[0] = new EmailAddressType(); //message.ToRecipients[1] = new EmailAddressType(); //message.ToRecipients[2] = new EmailAddressType(); message.ToRecipients[0].EmailAddress = "[email protected]"; message.ToRecipients[0].RoutingType = "SMTP"; //message.CcRecipients = new EmailAddressType[1]; //message.CcRecipients[0] = new EmailAddressType(); //message.CcRecipients[0].EmailAddress = toEmailAddress.ElementAt(1).ToString(); //message.CcRecipients[0].RoutingType = "SMTP"; //There are some more properties in MessageType object //you can set all according to your requirement // Construct the array of items to send request.Items = new NonEmptyArrayOfAllItemsType(); request.Items.Items = new ItemType[1]; request.Items.Items[0] = message; // Call the CreateItem EWS method. CreateItemResponseType response = esb.CreateItem(request);

Read the article

KVM Virtual guest Paused on Reboot

- by David Hamilton

I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

Read the article

Problem upgrading kernel on debian 3.1

- by exhuma

Hi, I have a quite old box in a remote server farm. So I have no direct access. Only remote SSH (and via SSH to a serial console). I haven't updated this box in ages. Now, whenever I want to install a new package, a dependency to glibc appears. Unfortunately, the install of glibc depends on a 2.6 kernel and I am running a venerable 2.4 kernel (one more reason to upgrade). The problem is, that the install of a new kernel has an indirect (over locales) dependency to glibc. So, to install glibc, I need a new kernel. For a new kernel, I need to upgrade glibc. Essentially I am blocked. What's the best way to proceed considering I have no "hardware" access? Here's a quick transcript of the upgrade process: [green:~]% sudo aptitude install linux-image-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages are unused and will be REMOVED: gcc-4.3-base The following NEW packages will be automatically installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 module-init-tools yaird The following packages have been kept back: adduser apache2 apache2-mpm-prefork apache2-utils apache2.2-common apt apt-utils aptitude autoconf autotools-dev awstats base-files base-passwd [...snip...] util-linux vacation vim vim-common wamerican wbritish wget whiptail whois wwwconfig-common zlib1g The following NEW packages will be installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 linux-image-686 module-init-tools yaird The following packages will be upgraded: hotplug libc6 2 packages upgraded, 8 newly installed, 1 to remove and 277 not upgraded. Need to get 0B/22.7MB of archives. After unpacking 52.1MB will be used. Do you want to continue? [Y/n/?] Writing extended state information... Done Preconfiguring packages ... (Reading database ... 34065 files and directories currently installed.) Preparing to replace libc6 2.3.6.ds1-13 (using .../libc6_2.7-18lenny2_i386.deb) ... Checking for services that may need to be restarted... Checking init scripts... WARNING: init script for postgresql not found. [ --- libc6 config screen appears here --- ] WARNING: POSIX threads library NPTL requires kernel version 2.6.8 or later. If you use a kernel 2.4, please upgrade it before installing glibc. The installation of a 2.6 kernel _could_ ask you to install a new libc first, this is NOT a bug, and should *NOT* be reported. In that case, please add etch sources to your /etc/apt/sources.list and run: apt-get install -t etch linux-image-2.6 Then reboot into this new kernel, and proceed with your upgrade dpkg: error processing /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb (--unpack): subprocess pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Ack! Something bad happened while installing packages. Trying to recover: dpkg: dependency problems prevent configuration of locales: locales depends on glibc-2.7-1; however: Package glibc-2.7-1 is not installed. dpkg: error processing locales (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: locales Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done Now, if I follow the instrunctions as promted I get the following. Note that I am using aptitude instead of apt-get to benefit from the better dependency tracking. I did try with apt-get first. But that let me to the same problem. [green:~]% sudo aptitude install -t etch linux-image-2.6.26-2-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done E: Unable to correct problems, you have held broken packages. E: Unable to correct dependencies, some packages cannot be installed E: Unable to resolve some dependencies! Some packages had unmet dependencies. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following packages have unmet dependencies: linux-image-2.6.26-2-686: Depends: initramfs-tools (>= 0.55) but it is not installable or yaird (>= 0.0.13) but it is not installable or linux-initramfs-tool which is a virtual package. Any ideas?

Read the article

How Hacker Can Access VPS CentOS 6 content?

- by user2118559

Just want to understand. Please, correct mistakes and write advices Hacker can access to VPS: 1. Through (using) console terminal, for example, using PuTTY. To access, hacker need to know port number, username and password. Port number hacker can know scanning open ports and try to login. The only way to login as I understand need to know username and password. To block (make more difficult) port scanning, need to use iptables configure /etc/sysconfig/iptables. I followed this https://www.digitalocean.com/community/articles/how-to-setup-a-basic-ip-tables-configuration-on-centos-6 tutorial and got *nat :PREROUTING ACCEPT [87:4524] :POSTROUTING ACCEPT [77:4713] :OUTPUT ACCEPT [77:4713] COMMIT *mangle :PREROUTING ACCEPT [2358:200388] :INPUT ACCEPT [2358:200388] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2638:477779] :POSTROUTING ACCEPT [2638:477779] COMMIT *filter :INPUT DROP [1:40] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [339:56132] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -p tcp -m tcp ! --tcp-flags FIN,SYN,RST,ACK SYN -m state --state NEW -j DROP -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG FIN,SYN,RST,PSH,ACK,URG -j DROP -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 110 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 21 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 21 -j ACCEPT COMMIT Regarding ports that need to be opened. If does not use ssl, then seems must leave open port 80 for website. Then for ssh (default 22) and for ftp (default 21). And set ip address, from which can connect. So if hacker uses other ip address, he can not access even knowing username and password? Regarding emails not sure. If I send email, using Gmail (Send mail as: (Use Gmail to send from your other email addresses)), then port 25 not necessary. For incoming emails at dynadot.com I use Email Forwarding. Does it mean that emails “does not arrive to VPS” (before arriving to VPS, emails are forwarded, for example to Gmail)? If emails does not arrive to VPS, then seems port 110 also not necessary. If use only ssl, must open port 443 and close port 80. Do not understand regarding port 3306 In PuTTY with /bin/netstat -lnp see Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 992/mysqld As understand it is for mysql. But does not remember that I have opened such port (may be when installed mysql, the port is opened automatically?). Mysql is installed on the same server, where all other content. Need to understand regarding port 3306 2. Also hacker may be able access console terminal through VPS hosting provider Control Panel (serial console emergency access). As understand only using console terminal (PuTTY, etc.) can make “global” changes (changes that can not modify with ftp). 3. Hacker can access to my VPS exploiting some hole in my php code and uploading, for example, Trojan. Unfortunately, faced situation that VPS was hacked. As understand it was because I used ZPanel. On VPS ( \etc\zpanel\panel\bin) ) found one php file, that was identified as Trojan by some virus scanners (at virustotal.com). Experimented with the file on local computer (wamp). And appears that hacker can see all content of VPS, rename, delete, upload etc. From my opinion, if in PuTTY use command like chattr +i /etc/php.ini then hacker could not be able to modify php.ini. Is there any other way to get into VPS?

Read the article

OSError : [Errno 38] Function not implemented - Django Celery implementation

- by Jordan Messina

I installed django-celery and I tried to start up the worker server but I get an OSError that a function isn't implemented. I'm running CentOS release 5.4 (Final) on a VPS: . broker -> amqp://guest@localhost:5672/ . queues -> . celery -> exchange:celery (direct) binding:celery . concurrency -> 4 . loader -> djcelery.loaders.DjangoLoader . logfile -> [stderr]@WARNING . events -> OFF . beat -> OFF [2010-07-22 17:10:01,364: WARNING/MainProcess] Traceback (most recent call last): [2010-07-22 17:10:01,364: WARNING/MainProcess] File "manage.py", line 11, in <module> [2010-07-22 17:10:01,364: WARNING/MainProcess] execute_manager(settings) [2010-07-22 17:10:01,364: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/django/core/management/__init__.py", line 438, in execute_manager [2010-07-22 17:10:01,364: WARNING/MainProcess] utility.execute() [2010-07-22 17:10:01,364: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/django/core/management/__init__.py", line 379, in execute [2010-07-22 17:10:01,365: WARNING/MainProcess] self.fetch_command(subcommand).run_from_argv(self.argv) [2010-07-22 17:10:01,365: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/django/core/management/base.py", line 191, in run_from_argv [2010-07-22 17:10:01,365: WARNING/MainProcess] self.execute(*args, **options.__dict__) [2010-07-22 17:10:01,365: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/django/core/management/base.py", line 218, in execute [2010-07-22 17:10:01,365: WARNING/MainProcess] output = self.handle(*args, **options) [2010-07-22 17:10:01,365: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/django_celery-2.0.0-py2.6.egg/djcelery/management/commands/celeryd.py", line 22, in handle [2010-07-22 17:10:01,366: WARNING/MainProcess] run_worker(**options) [2010-07-22 17:10:01,366: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/celery-2.0.1-py2.6.egg/celery/bin/celeryd.py", line 385, in run_worker [2010-07-22 17:10:01,366: WARNING/MainProcess] return Worker(**options).run() [2010-07-22 17:10:01,366: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/celery-2.0.1-py2.6.egg/celery/bin/celeryd.py", line 218, in run [2010-07-22 17:10:01,366: WARNING/MainProcess] self.run_worker() [2010-07-22 17:10:01,366: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/celery-2.0.1-py2.6.egg/celery/bin/celeryd.py", line 312, in run_worker [2010-07-22 17:10:01,367: WARNING/MainProcess] worker.start() [2010-07-22 17:10:01,367: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/celery-2.0.1-py2.6.egg/celery/worker/__init__.py", line 206, in start [2010-07-22 17:10:01,367: WARNING/MainProcess] component.start() [2010-07-22 17:10:01,367: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/celery-2.0.1-py2.6.egg/celery/concurrency/processes/__init__.py", line 54, in start [2010-07-22 17:10:01,367: WARNING/MainProcess] maxtasksperchild=self.maxtasksperchild) [2010-07-22 17:10:01,367: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/celery-2.0.1-py2.6.egg/celery/concurrency/processes/pool.py", line 448, in __init__ [2010-07-22 17:10:01,368: WARNING/MainProcess] self._setup_queues() [2010-07-22 17:10:01,368: WARNING/MainProcess] File "/usr/local/lib/python2.6/site-packages/celery-2.0.1-py2.6.egg/celery/concurrency/processes/pool.py", line 564, in _setup_queues [2010-07-22 17:10:01,368: WARNING/MainProcess] self._inqueue = SimpleQueue() [2010-07-22 17:10:01,368: WARNING/MainProcess] File "/usr/local/lib/python2.6/multiprocessing/queues.py", line 315, in __init__ [2010-07-22 17:10:01,368: WARNING/MainProcess] self._rlock = Lock() [2010-07-22 17:10:01,368: WARNING/MainProcess] File "/usr/local/lib/python2.6/multiprocessing/synchronize.py", line 117, in __init__ [2010-07-22 17:10:01,369: WARNING/MainProcess] SemLock.__init__(self, SEMAPHORE, 1, 1) [2010-07-22 17:10:01,369: WARNING/MainProcess] File "/usr/local/lib/python2.6/multiprocessing/synchronize.py", line 49, in __init__ [2010-07-22 17:10:01,369: WARNING/MainProcess] sl = self._semlock = _multiprocessing.SemLock(kind, value, maxvalue) [2010-07-22 17:10:01,369: WARNING/MainProcess] OSError [2010-07-22 17:10:01,369: WARNING/MainProcess] : [2010-07-22 17:10:01,369: WARNING/MainProcess] [Errno 38] Function not implemented Am I just totally screwed and should use a new kernel that has this implemented or is there an easy way to resolve this?

Read the article

vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

- by kce

I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

Read the article

DKIMPROXY signing wrong domain

- by user64566

Just.... wont sign a thing... The dkimproxy_out.conf: # specify what address/port DKIMproxy should listen on listen 127.0.0.1:10028 # specify what address/port DKIMproxy forwards mail to relay 127.0.0.1:10029 # specify what domains DKIMproxy can sign for (comma-separated, no spaces) domain tinymagnet.com,hypnoenterprises.com # specify what signatures to add signature dkim(c=relaxed) signature domainkeys(c=nofws) # specify location of the private key keyfile /etc/postfix/dkim/private.key # specify the selector (i.e. the name of the key record put in DNS) selector mail The direct connection straight to the server, making it clear that this is a problem with dkimproxy and not postfix... mmxbass@hypno1:~$ telnet localhost 10028 Trying 127.0.0.1... Connected to localhost.localdomain. Escape character is '^]'. 220 hypno1.hypnoenterprises.com ESMTP Postfix (Debian/GNU) EHLO hypno1.hypnoenterprises.com 250-hypno1.hypnoenterprises.com 250-PIPELINING 250-SIZE 250-ETRN 250-STARTTLS 250-AUTH PLAIN LOGIN 250-AUTH=PLAIN LOGIN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN MAIL FROM:<[email protected]> 250 2.1.0 Ok RCPT TO:<[email protected]> 250 2.1.5 Ok DATA 354 End data with <CR><LF>.<CR><LF> SUBJECT:test . 250 2.0.0 Ok: queued as B62A78D94F QUIT 221 2.0.0 Bye Now lets look at the mail headers as reported by myiptest.com: From [email protected] Thu Dec 23 18:57:14 2010 Return-path: Envelope-to: [email protected] Delivery-date: Thu, 23 Dec 2010 18:57:14 +0000 Received: from [184.82.95.154] (helo=hypno1.hypnoenterprises.com) by myiptest.com with esmtp (Exim 4.69) (envelope-from ) id 1PVqLi-0004YR-5f for [email protected]; Thu, 23 Dec 2010 18:57:14 +0000 Received: from hypno1.hypnoenterprises.com (localhost.localdomain [127.0.0.1]) by hypno1.hypnoenterprises.com (Postfix) with ESMTP id 878418D902 for ; Thu, 23 Dec 2010 13:57:26 -0500 (EST) DKIM-Signature: v=1; a=rsa-sha1; c=simple; d=hypnoenterprises.com; h= from:to:subject:date:mime-version:content-type :content-transfer-encoding:message-id; s=mail; bh=uoq1oCgLlTqpdD X/iUbLy7J1Wic=; b=HxBKTGjzTpZSZU8xkICtARCKxqriqZK+qHkY1U8qQlOw+S S1wlZxzTeDGIOgeiTviGDpcKWkLLTMlUvx8dY4FuT8K1/raO9nMC7xjG2uLayPX0 zLzm4Srs44jlfRQIjrQd9tNnp35Wkry6dHPv1u21WUvnDWaKARzGGHRLfAzW4= Received: from localhost (localhost.localdomain [127.0.0.1]) by hypno1.hypnoenterprises.com (Postfix) with ESMTP id 2A04A8D945 for ; Thu, 23 Dec 2010 13:57:26 -0500 (EST) X-Virus-Scanned: Debian amavisd-new at hypno1.hypnoenterprises.com Received: from hypno1.hypnoenterprises.com ([127.0.0.1]) by localhost (hypno1.hypnoenterprises.com [127.0.0.1]) (amavisd-new, port 10024) with ESMTP id Ua7BnnzmIaUO for ; Thu, 23 Dec 2010 13:57:25 -0500 (EST) Received: from phoenix.localnet (c-76-23-245-211.hsd1.ma.comcast.net [76.23.245.211]) (using TLSv1 with cipher DHE-RSA-AES256-SHA (256/256 bits)) (No client certificate requested) by hypno1.hypnoenterprises.com (Postfix) with ESMTPSA id 48A0D8D90D for ; Thu, 23 Dec 2010 13:57:25 -0500 (EST) From: Joshua Pech To: [email protected] Subject: test Date: Thu, 23 Dec 2010 13:57:25 -0500 User-Agent: KMail/1.13.5 (Linux/2.6.32-5-amd64; KDE/4.4.5; x86_64; ; ) MIME-Version: 1.0 Content-Type: Text/Plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Message-Id: DomainKey-Status: no signature Received-SPF: pass (myiptest.com: domain of tinymagnet.com designates 184.82.95.154 as permitted sender) Notice how the dkim signature specifies the d=hypnoenterprises.com.... why?

Read the article

ssh login fails for user with empty password

- by Reid

How do you enable ssh login on OS X 10.8 (Mountain Lion) for a user with an empty password? I've seen others asking this question, and like me it's for the same reason: a parent who can't deal with passwords. So "set a password" is not an option. I found references to adding "nullok" to various PAM config files. Didn't work. Found sshd config "PermitEmptyPasswords yes". Didn't work. I've done a diff on "ssh -vvv" between a successful ssh with a password-enabled account and the one with no password. 54,55c54,55 < debug2: dh_gen_key: priv key bits set: 133/256 < debug2: bits set: 533/1024 --- > debug2: dh_gen_key: priv key bits set: 140/256 > debug2: bits set: 508/1024 67c67 < debug2: bits set: 509/1024 --- > debug2: bits set: 516/1024 79c79 < debug2: key: /Users/rae/.ssh/rae (0x7f9a0241e2c0) --- > debug2: key: /Users/rae/.ssh/rae (0x7f81e0c1e2c0) 90,116c90,224 < debug1: Authentications that can continue: publickey,keyboard-interactive < debug2: we did not send a packet, disable method < debug3: authmethod_lookup keyboard-interactive < debug3: remaining preferred: password < debug3: authmethod_is_enabled keyboard-interactive < debug1: Next authentication method: keyboard-interactive < debug2: userauth_kbdint < debug2: we sent a keyboard-interactive packet, wait for reply < debug2: input_userauth_info_req < debug2: input_userauth_info_req: num_prompts 1 < debug3: packet_send2: adding 32 (len 14 padlen 18 extra_pad 64) < debug1: Authentications that can continue: publickey,keyboard-interactive < debug2: userauth_kbdint < debug2: we sent a keyboard-interactive packet, wait for reply < debug2: input_userauth_info_req < debug2: input_userauth_info_req: num_prompts 1 < debug3: packet_send2: adding 32 (len 14 padlen 18 extra_pad 64) < debug1: Authentications that can continue: publickey,keyboard-interactive < debug2: userauth_kbdint < debug2: we sent a keyboard-interactive packet, wait for reply < debug2: input_userauth_info_req < debug2: input_userauth_info_req: num_prompts 1 < debug3: packet_send2: adding 32 (len 14 padlen 18 extra_pad 64) < debug1: Authentications that can continue: publickey,keyboard-interactive < debug2: we did not send a packet, disable method < debug1: No more authentication methods to try. < Permission denied (publickey,keyboard-interactive). --- > debug1: Server accepts key: pkalg ssh-dss blen 433 > debug2: input_userauth_pk_ok: fp 6e:02:20:63:48:6a:08:99:b8:5f:12:d8:d5:3d:e1:fb > debug3: sign_and_send_pubkey: DSA 6e:02:20:63:48:6a:08:99:b8:5f:12:d8:d5:3d:e1:fb > debug1: read PEM private key done: type DSA > debug1: Authentication succeeded (publickey). > Authenticated to cme-mini.local ([192.168.1.5]:22). > debug2: fd 7 setting O_NONBLOCK > debug3: fd 8 is O_NONBLOCK > debug1: channel 0: new [client-session] > debug3: ssh_session2_open: channel_new: 0 > debug2: channel 0: send open > debug1: Requesting [email protected] > debug1: Entering interactive session. > debug2: callback start > debug2: client_session2_setup: id 0 > debug2: fd 5 setting TCP_NODELAY > debug2: channel 0: request pty-req confirm 1 > debug1: Sending environment.

Read the article

vlans on openvz, centos 6

- by arheops

i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

Read the article

Load average is have been high over some period

- by user111196

We have a dedicated MySQL server and below is the a snapshot of the top. The load average has been staying at nearly 100 for an hour plus ready. top - 20:54:28 up 7:31, 2 users, load average: 83.08, 96.88, 106.23 Tasks: 278 total, 2 running, 274 sleeping, 2 stopped, 0 zombie Cpu0 : 18.8%us, 10.2%sy, 0.0%ni, 70.9%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 51.2%us, 4.3%sy, 0.0%ni, 44.2%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu2 : 9.0%us, 10.3%sy, 0.0%ni, 80.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 18.8%us, 7.4%sy, 0.0%ni, 73.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 7.8%us, 8.8%sy, 0.0%ni, 83.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu5 : 10.3%us, 8.4%sy, 0.0%ni, 81.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu6 : 6.2%us, 7.5%sy, 0.0%ni, 86.2%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu7 : 6.2%us, 6.2%sy, 0.0%ni, 87.3%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu8 : 8.8%us, 10.4%sy, 0.0%ni, 80.5%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu9 : 63.7%us, 4.6%sy, 0.0%ni, 12.2%id, 0.0%wa, 4.3%hi, 15.2%si, 0.0%st Cpu10 : 9.2%us, 10.2%sy, 0.0%ni, 80.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu11 : 17.3%us, 5.9%sy, 0.0%ni, 76.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu12 : 8.0%us, 8.7%sy, 0.0%ni, 83.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu13 : 10.9%us, 7.4%sy, 0.0%ni, 81.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu14 : 6.2%us, 6.9%sy, 0.0%ni, 86.9%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu15 : 4.8%us, 6.1%sy, 0.0%ni, 89.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 33009800k total, 23174396k used, 9835404k free, 120604k buffers Swap: 35061752k total, 0k used, 35061752k free, 16459540k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3341 mysql 20 0 14.3g 4.6g 4240 S 417.8 14.5 1673:51 mysqld 24406 root 20 0 15008 1292 876 R 0.3 0.0 0:00.19 top 1 root 20 0 4080 852 608 S 0.0 0.0 0:01.92 init 2 root 15 -5 0 0 0 S 0.0 0.0 0:00.00 kthreadd 3 root RT -5 0 0 0 S 0.0 0.0 0:00.32 migration/0 4 root 15 -5 0 0 0 S 0.0 0.0 0:00.29 ksoftirqd/0 5 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 6 root RT -5 0 0 0 S 0.0 0.0 0:03.21 migration/1 7 root 15 -5 0 0 0 S 0.0 0.0 0:00.07 ksoftirqd/1 8 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 9 root RT -5 0 0 0 S 0.0 0.0 0:00.17 migration/2 10 root 15 -5 0 0 0 S 0.0 0.0 0:00.03 ksoftirqd/2 11 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/2 12 root RT -5 0 0 0 S 0.0 0.0 0:00.32 migration/3 13 root 15 -5 0 0 0 S 0.0 0.0 0:00.02 ksoftirqd/3 14 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/3 15 root RT -5 0 0 0 S 0.0 0.0 0:00.10 migration/4 16 root 15 -5 0 0 0 S 0.0 0.0 0:00.04 ksoftirqd/4 17 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/4 18 root RT -5 0 0 0 S 0.0 0.0 0:00.35 migration/5 We have also tried to run this command. What else command can help us diagnose the exact problem of this high load? netstat -nat |grep 3306 | awk '{print $6}' | sort | uniq -c | sort -n 1 LISTEN 1 SYN_RECV 410 ESTABLISHED 964 TIME_WAIT Output of vmstat 1: ---------------memory--------------- --swap-- --io-- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 0 0 12978936 30944 15172360 0 0 259 3 184 265 6 6 77 12 0

Read the article

centos6.3 varnish3.03 get the wrong backend

- by Sola.Shawn

I install varnish3.03 with yum! I got a problem with it my varnish config bellow:** # #backend weibo { .host = "192.168.1.178"; .port = "8080"; .connect_timeout=20s; .first_byte_timeout=20s; .between_bytes_timeout=20s; } #backend smth { .host = "192.168.1.115"; .port = "8080"; .connect_timeout=20s; .first_byte_timeout=20s; .between_bytes_timeout=20s; } #sub vcl_recv { if (req.restarts == 0) { if (req.http.x-forwarded-for) { set req.http.X-Forwarded-For = req.http.X-Forwarded-For + ", " + client.ip; } else { set req.http.X-Forwarded-For = client.ip; } } if (req.request != "GET" && req.request != "HEAD" && req.request != "PUT" && req.request != "POST" && req.request != "TRACE" && req.request != "OPTIONS" && req.request != "DELETE") { # /* Non-RFC2616 or CONNECT which is weird. */ return(pipe); } if (req.request != "GET" && req.request != "HEAD") { # /* We only deal with GET and HEAD by default */ return(pass); } if (req.http.Authorization || req.http.Cookie) { /* Not cacheable by default */ return(pass); } if (req.http.host ~ "^(hk.)?weibo.com"){ set req.http.host = "hk.weibo.com"; set req.backend = weibo; } elseif (req.http.host ~ "^(www.)?newsmth.net"){ set req.http.host = "www.newsmth.net"; set req.backend = smth; } else { error 404 "Unknown virtual host"; } return(lookup); } ##sub vcl_pipe { return(pipe); } #sub vcl_pass { return(pass); } #sub vcl_hash { hash_data(req.url); if(req.http.host) { hash_data(req.http.host); } else { hash_data(server.ip); } return(hash); } #sub vcl_hit { if(req.http.Cache-Control~"no-cache"||req.http.Cache-Control~"max-age=0"||req.http.Pragma~"no-cache"){ set obj.ttl=0s; return (restart); } return(deliver); } #sub vcl_miss { return(fetch); } #sub vcl_fetch { if (beresp.ttl <= 120s || beresp.http.Set-Cookie || beresp.http.Vary == "*") { /* * Mark as "Hit-For-Pass" for the next 2 minutes */ set beresp.ttl = 10s; return (hit_for_pass); } return(deliver); } #sub vcl_deliver { return(deliver); } #sub vcl_init { return(ok); } #sub vcl_fini { return(ok); } and my Win7's hosts file add bellow: 192.168.1.178 www.newsmth.net 192.168.1.178 hk.weibo.com start varnish varnishd -f /etc/varnish/dd.vcl -s malloc,100M -a 0.0.0.0:8000 -T 0.0.0.0:3500<br> but when I access the "hk.weibo.com:8000" it fine, and got: Hello,I am hk.weibo.com! but when access http://www.newsmth.net:8000/, got: Hello,I am hk.weibo.com! <br> My question is why it isn't "Hello,I am www.newsmth.net!"? varnish fetched the content from the wrong backend. Does anyone know how to fix this?

Read the article

Looking for advice on Hyper-v storage replication

- by Notre1

I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

Read the article

Windows 7, HTTPS WebDav: Asks for password twice and fails. Any workarounds?

- by AutoDMC

Howdy. I have a Dav server running with PHP SabreDav (code.google.com/p/sabredav/wiki/Windows) on Cherokee at an HTTPS secured URL. It's set to use https, and uses Digest Authentication. I can log in with multiple browsers and a few third party clients (BitKinex and Java AnyClient can connect and browse as well, caveats below). However, when attempting to log in with Windows 7 (surprise, surprise), it asks for my password twice, then tells me that my folder is invalid. I have verified that the server is using Digest authentication. I've verified multiple times that third party software can connect. I even went out and bought a GoDaddy SSL certificate so my SSL wouldn't be self signed anymore. I've applied the registry hacks here: support.microsoft.com/kb/943280 (Note that the article says the "fix" already exists for Windows 7, I just need magical registry hax to get it to work) I've applied the registry hacks here: support.microsoft.com/kb/941050 I've applied the registry hacks here: support.microsoft.com/kb/841215 (Supposedly allows Basic Auth, which shouldn't apply, but why not?) All to no avail; Windows continues to ask for my password twice, then state that "The folder you entered does not appear to be valid. Please choose another." Try the command line? Sure: I've attempted to access with NET USE "https://dav.example.com/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/" (System error 1790) I've attempted to access with NET USE "https://dav.example.com/subdir/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/subdir/" (System error 1790) For good luck: ping dav.example.com ... works. And again, web browsers can access the share just fine, so can third party tools. Best I can tell at this point is "HAHA, NO WEBDAV FOR YOU ON WINDOWS 7" which would be fine except everyone who will be using this application... uses Windows 7. And most are not as persistent or pugnacious as I am. I feel like I've burned through every random suggestion I've found anywhere in the first 10 pages of Google on every search term I can think of. Any ideas? I need it to be Webdav, I need it to be over HTTPS, and I really do need a method to access it from Windows 7. EXTRA DETAIL: However, the "third party" programs I've tried have either been buggy, incomplete, or have silly ... "glitches." For example, BitKinex seems to fixate on any http error codes sent, so if there's a glitch reading a directory, BAM, that directory is always listed empty. Long directory listings also show up as blank, even though the transfer panel shows that directory listing is still taking place. In any case, BitKinex is useless for development purposes for the reasons above. And besides, I'm building this for people other than myself, people who will want to get this dav share working "the regular way."

Read the article

Frequent Kernel Panic on CentOS 6.5

- by Manuel Sopena Ballesteros

I have a webserver with the configuration below: VMWare ESXi environemt CPanel installed CentOS release 6.5 (Final) 4 CPUs 2G RAM 2x VM disks 100G each LVM system My issue is I am getting kernel panic quite frequently. These is a list of some processes blocked I could see from the console: mysqld queueprocd httpd suphp vmtoolsd loop0 auditd this is my sar logs Linux 2.6.32-431.3.1.el6.x86_64 (test01) 08/22/2014 _x86_64_ (4 CPU) 12:00:01 AM CPU %user %nice %system %iowait %steal %idle 12:10:01 AM all 26.86 0.01 0.98 0.57 0.00 71.57 12:20:01 AM all 1.78 0.02 1.03 0.08 0.00 97.09 12:30:01 AM all 26.34 0.02 0.85 0.05 0.00 72.74 12:40:01 AM all 27.12 0.01 1.11 1.22 0.00 70.54 12:50:01 AM all 1.59 0.02 0.94 0.13 0.00 97.32 01:00:01 AM all 26.10 0.01 0.77 0.04 0.00 73.07 01:10:01 AM all 27.51 0.01 1.16 0.14 0.00 71.18 01:20:01 AM all 1.80 0.07 1.06 0.08 0.00 96.99 01:30:01 AM all 26.19 0.01 0.78 0.05 0.00 72.96 01:40:01 AM all 26.62 0.02 0.87 0.05 0.00 72.45 01:50:02 AM all 1.35 0.01 0.87 0.02 0.00 97.75 02:00:01 AM all 26.11 0.02 0.69 0.02 0.00 73.17 02:10:01 AM all 26.73 0.02 0.89 0.14 0.00 72.21 02:20:01 AM all 1.45 0.01 0.92 0.04 0.00 97.58 02:30:01 AM all 26.59 0.01 1.06 0.03 0.00 72.31 02:40:01 AM all 26.27 0.01 0.72 0.05 0.00 72.95 02:50:01 AM all 0.86 0.01 0.50 0.09 0.00 98.53 03:00:01 AM all 25.61 0.02 0.39 0.03 0.00 73.96 03:10:01 AM all 26.30 0.08 0.66 0.14 0.00 72.82 03:20:01 AM all 0.81 0.01 0.51 0.04 0.00 98.63 03:30:02 AM all 26.15 0.02 0.53 0.07 0.00 73.24 03:40:01 AM all 26.06 0.01 0.47 0.04 0.00 73.42 03:50:01 AM all 0.96 0.02 0.51 0.03 0.00 98.48 Average: all 17.69 0.02 0.79 0.14 0.00 81.36 06:58:14 AM LINUX RESTART 07:00:01 AM CPU %user %nice %system %iowait %steal %idle 07:10:01 AM all 1.04 0.02 0.57 0.95 0.00 97.42 07:20:02 AM all 0.66 0.01 0.39 0.06 0.00 98.87 07:30:01 AM all 25.71 0.01 0.45 0.16 0.00 73.67 07:40:01 AM all 25.88 0.01 0.35 0.08 0.00 73.68 As you can see the server became unresponsive at 03.50 AM and I had to reset the VM at 06.58 AM to fix it. sar -d 03:00:01 PM dev8-16 0.16 0.01 3.37 20.78 0.00 12.40 9.29 0.15 03:00:01 PM dev8-0 4.08 5.72 77.50 20.38 0.06 15.15 3.13 1.28 03:00:01 PM dev253-0 10.37 5.74 80.87 8.35 0.13 12.52 1.24 1.29 03:00:01 PM dev253-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 03:10:01 PM dev8-16 0.27 0.17 3.17 12.22 0.00 11.49 7.95 0.22 03:10:01 PM dev8-0 6.37 18.98 136.19 24.34 0.05 7.25 2.18 1.39 03:10:01 PM dev253-0 17.91 19.15 137.94 8.77 0.13 7.11 0.78 1.41 03:10:01 PM dev253-1 0.18 0.00 1.41 8.00 0.00 9.09 0.52 0.01 03:10:01 PM DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util 03:20:01 PM dev8-16 0.17 0.23 2.04 13.39 0.00 6.07 5.29 0.09 03:20:01 PM dev8-0 3.83 18.57 78.45 25.35 0.05 13.25 2.73 1.05 03:20:01 PM dev253-0 10.30 18.80 80.49 9.64 0.14 13.89 1.03 1.06 03:20:01 PM dev253-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 03:30:01 PM dev8-16 0.26 0.16 4.59 18.56 0.00 6.44 5.54 0.14 03:30:01 PM dev8-0 5.97 24.07 117.83 23.77 0.05 8.53 2.13 1.27 03:30:01 PM dev253-0 15.90 24.23 122.42 9.22 0.12 7.71 0.81 1.29 03:30:01 PM dev253-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 03:40:01 PM dev8-16 0.20 0.00 2.32 11.44 0.00 8.35 5.90 0.12 03:40:01 PM dev8-0 4.39 19.58 77.94 22.24 0.06 12.87 2.12 0.93 03:40:01 PM dev253-0 10.25 19.58 80.25 9.74 0.12 11.63 0.91 0.94 03:40:01 PM dev253-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 03:50:01 PM dev8-16 0.23 0.50 2.32 12.44 0.00 6.27 5.13 0.12 03:50:01 PM dev8-0 5.09 9.00 95.04 20.45 0.04 7.36 2.10 1.07 03:50:01 PM dev253-0 12.47 9.50 96.82 8.53 0.08 6.76 0.87 1.08 03:50:01 PM dev253-1 0.07 0.00 0.54 8.00 0.00 14.10 0.40 0.00 04:00:01 PM dev8-16 0.21 0.00 2.04 9.89 0.00 7.00 5.87 0.12 04:00:01 PM dev8-0 4.68 1.64 94.70 20.57 0.05 10.71 2.41 1.13 04:00:01 PM dev253-0 12.27 1.64 96.74 8.02 0.12 9.95 0.93 1.14 sar -q 01:00:01 AM 6 205 2.02 1.32 0.81 01:10:01 AM 3 187 0.08 0.72 0.86 01:20:01 AM 2 187 0.04 0.18 0.49 01:30:01 AM 4 205 2.04 1.34 0.82 01:40:01 AM 2 185 0.02 0.68 0.83 01:50:02 AM 1 185 0.08 0.15 0.45 02:00:01 AM 5 202 2.02 1.30 0.78 02:10:01 AM 4 185 0.11 0.72 0.84 02:20:01 AM 1 183 0.17 0.15 0.45 02:30:01 AM 5 206 2.03 1.32 0.79 02:40:01 AM 2 184 0.08 0.70 0.83 02:50:01 AM 1 183 0.00 0.10 0.43 03:00:01 AM 7 205 2.03 1.32 0.78 03:10:01 AM 2 194 0.34 0.73 0.83 03:20:01 AM 1 184 0.00 0.13 0.44 03:30:02 AM 4 201 2.04 1.32 0.78 03:40:01 AM 2 193 0.06 0.67 0.81 03:50:01 AM 1 183 0.06 0.12 0.43 Average: 3 192 0.68 0.70 0.69 06:58:14 AM LINUX RESTART 07:00:01 AM runq-sz plist-sz ldavg-1 ldavg-5 ldavg-15 07:10:01 AM 2 181 0.00 0.09 0.11 07:20:02 AM 1 179 0.00 0.00 0.04 07:30:01 AM 4 197 2.12 1.33 0.58 sar -r Linux 2.6.32-431.3.1.el6.x86_64 (test01) 08/22/2014 _x86_64_ (4 CPU) 12:00:01 AM kbmemfree kbmemused %memused kbbuffers kbcached kbcommit %commit 12:10:01 AM 227484 1694468 88.16 117444 917004 635308 10.50 12:20:01 AM 219692 1702260 88.57 119556 920540 630940 10.43 12:30:01 AM 196248 1725704 89.79 121376 923592 695048 11.49 12:40:01 AM 127524 1794428 93.36 125004 1016196 633048 10.46 12:50:01 AM 127156 1794796 93.38 128212 1014536 624992 10.33 01:00:01 AM 110764 1811188 94.24 129964 1001608 700016 11.57 01:10:01 AM 160560 1761392 91.65 132260 973472 628640 10.39 01:20:01 AM 133076 1788876 93.08 134144 982608 655524 10.83 01:30:01 AM 121512 1800440 93.68 135548 985676 700500 11.58 01:40:01 AM 140640 1781312 92.68 137220 988576 628280 10.38 01:50:02 AM 139160 1782792 92.76 138688 990672 625224 10.33 02:00:01 AM 106112 1815840 94.48 139940 993976 700360 11.57 02:10:01 AM 155400 1766552 91.91 142112 971864 625656 10.34 02:20:01 AM 154056 1767896 91.98 143732 975556 621352 10.27 02:30:01 AM 110856 1811096 94.23 145032 978288 709360 11.72 02:40:01 AM 140200 1781752 92.71 146568 980656 624872 10.33 02:50:01 AM 137600 1784352 92.84 148940 984484 621948 10.28 03:00:01 AM 105032 1816920 94.54 150208 985736 706060 11.67 03:10:01 AM 168996 1752956 91.21 154708 941500 656312 10.85 03:20:01 AM 169408 1752544 91.19 156096 944100 621780 10.28 03:30:02 AM 132360 1789592 93.11 157724 951612 701296 11.59 03:40:01 AM 159012 1762940 91.73 158940 942560 656292 10.85 03:50:01 AM 163192 1758760 91.51 160312 944576 624544 10.32 Average: 148089 1773863 92.29 140162 969973 653363 10.80 06:58:14 AM LINUX RESTART 07:00:01 AM kbmemfree kbmemused %memused kbbuffers kbcached kbcommit %commit 07:10:01 AM 1016628 905324 47.10 85568 447556 600932 9.93 07:20:02 AM 1009996 911956 47.45 87616 451200 596156 9.85 07:30:01 AM 961128 960824 49.99 89164 464332 658912 10.89 07:40:01 AM 973376 948576 49.35 90880 473084 600176 9.92 dmesg does not show any relevant information. I don't see any bottleneck in sar, any idea what can I check next? thank you very much

Read the article

How can a single disk in a hardware SATA RAID-10 array bring the entire array to a screeching halt?

- by Stu Thompson

Prelude: I'm a code-monkey that's increasingly taken on SysAdmin duties for my small company. My code is our product, and increasingly we provide the same app as SaaS. About 18 months ago I moved our servers from a premium hosting centric vendor to a barebones rack pusher in a tier IV data center. (Literally across the street.) This ment doing much more ourselves--things like networking, storage and monitoring. As part the big move, to replace our leased direct attached storage from the hosting company, I built a 9TB two-node NAS based on SuperMicro chassises, 3ware RAID cards, Ubuntu 10.04, two dozen SATA disks, DRBD and . It's all lovingly documented in three blog posts: Building up & testing a new 9TB SATA RAID10 NFSv4 NAS: Part I, Part II and Part III. We also setup a Cacit monitoring system. Recently we've been adding more and more data points, like SMART values. I could not have done all this without the awesome boffins at ServerFault. It's been a fun and educational experience. My boss is happy (we saved bucket loads of $$$), our customers are happy (storage costs are down), I'm happy (fun, fun, fun). Until yesterday. Outage & Recovery: Some time after lunch we started getting reports of sluggish performance from our application, an on-demand streaming media CMS. About the same time our Cacti monitoring system sent a blizzard of emails. One of the more telling alerts was a graph of iostat await. Performance became so degraded that Pingdom began sending "server down" notifications. The overall load was moderate, there was not traffic spike. After logging onto the application servers, NFS clients of the NAS, I confirmed that just about everything was experiencing highly intermittent and insanely long IO wait times. And once I hopped onto the primary NAS node itself, the same delays were evident when trying to navigate the problem array's file system. Time to fail over, that went well. Within 20 minuts everything was confirmed to be back up and running perfectly. Post-Mortem: After any and all system failures I perform a post-mortem to determine the cause of the failure. First thing I did was ssh back into the box and start reviewing logs. It was offline, completely. Time for a trip to the data center. Hardware reset, backup an and running. In /var/syslog I found this scary looking entry: Nov 15 06:49:44 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_00], 6 Currently unreadable (pending) sectors Nov 15 06:49:44 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_07], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 171 to 170 Nov 15 06:49:45 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_10], 16 Currently unreadable (pending) sectors Nov 15 06:49:45 umbilo smartd[2827]: Device: /dev/twa0 [3ware_disk_10], 4 Offline uncorrectable sectors Nov 15 06:49:45 umbilo smartd[2827]: Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error Nov 15 06:49:45 umbilo smartd[2827]: # 1 Short offline Completed: read failure 90% 6576 3421766910 Nov 15 06:49:45 umbilo smartd[2827]: # 2 Short offline Completed: read failure 90% 6087 3421766910 Nov 15 06:49:45 umbilo smartd[2827]: # 3 Short offline Completed: read failure 10% 5901 656821791 Nov 15 06:49:45 umbilo smartd[2827]: # 4 Short offline Completed: read failure 90% 5818 651637856 Nov 15 06:49:45 umbilo smartd[2827]: So I went to check the Cacti graphs for the disks in the array. Here we see that, yes, disk 7 is slipping away just like syslog says it is. But we also see that disk 8's SMART Read Erros are fluctuating. There are no messages about disk 8 in syslog. More interesting is that the fluctuating values for disk 8 directly correlate to the high IO wait times! My interpretation is that: Disk 8 is experiencing an odd hardware fault that results in intermittent long operation times. Somehow this fault condition on the disk is locking up the entire array Maybe there is a more accurate or correct description, but the net result has been that the one disk is impacting the performance of the whole array. The Question(s) How can a single disk in a hardware SATA RAID-10 array bring the entire array to a screeching halt? Am I being naïve to think that the RAID card should have dealt with this? How can I prevent a single misbehaving disk from impacting the entire array? Am I missing something?

Read the article

Drupal & nginx : a sound "general purpose" configuration?

- by sbrattla

After a bit back and forth with configuring Drupal and nginx to work together, I've come up with the below configuration for a site. It works well, both with private and public file systems. However, as I am fairly new to nginx I'd like to hear if there is something with this configuration that I should change (for Please note! I'm aiming towards getting feedback on a general purpose Drupal configuration. That is, a configuration which others who are trying out Drupal + nginx can "copy paste" to get up and running. server { listen 80; server_name www.example.* example.*; access_log /home/example/www/logs/access.log; error_log /home/example/www/logs/error.log; root /home/example/www/public_html; # Site Icon location = /favicon.ico { log_not_found off; access_log off; } # Search Engines location = /robots.txt { allow all; log_not_found off; access_log off; } # Drush location = /backup { deny all; } # Very rarely should these ever be accessed from outside # the local network. location ~* \.(txt|log)$ { allow 10.0.0.0/8; allow 172.16.0.0/12; allow 192.168.0.0/16; deny all; } location ~ \..*/.*\.php$ { return 403; } # Default location location / { try_files $uri @rewrite; } # Files managed by Drupal will be served via PHP. location ~* /system/files/ { access_log off; try_files $uri @rewrite; } ## Images and static content is treated different location ~* \.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; expires 30d; } # Some Drupal modules enforce no slash (/) at the end # of the URL. location @rewrite { rewrite_log on; rewrite ^/(.*)$ /index.php?q=$1; } # PHP5-FPM is used to handle PHP. location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(.*)$; fastcgi_pass unix:/var/run/example.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_intercept_errors on; fastcgi_ignore_client_abort off; fastcgi_connect_timeout 60; fastcgi_send_timeout 180; fastcgi_read_timeout 180; fastcgi_buffer_size 128k; fastcgi_buffers 4 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; } ## Disable viewing .htaccess & .htpassword location ~ /\.ht { deny all; } }

Read the article

Connect to VPN from Mac on Time Capsule network

- by Lou Franco

I have a few clients on my network that can connect to my work VPN (Windows PPTP) when they are not on my home network. On my home network (Cable Modem with Time Capsule providing Wifi), it fails very early -- looks like it can't even establish a connection. Logs just say that it failed -- even verbose logs don't have much: I redacted the host and IP from this log, but I can ping it. Wed Feb 2 14:32:41 2011 : PPTP connecting to server 'XXX.XXX.com' (XXX.XX.XX.XX)... Wed Feb 2 14:32:41 2011 : PPTP connection established. Wed Feb 2 14:32:41 2011 : using link 0 Wed Feb 2 14:32:41 2011 : Using interface ppp0 Wed Feb 2 14:32:41 2011 : Connect: ppp0 <--> socket[34:17] Wed Feb 2 14:32:41 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:44 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:47 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:50 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:53 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:56 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:59 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:02 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:05 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:08 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:11 2011 : LCP: timeout sending Config-Requests Wed Feb 2 14:33:11 2011 : Connection terminated. Wed Feb 2 14:33:11 2011 : PPTP disconnecting... Wed Feb 2 14:33:11 2011 : PPTP disconnected Others can get to the VPN and I can too, but not on my network. The only clue I have seen in other forums is to set the NAT default host on the Time Capsule -- I set this to the IP that my mac got over DHCP. I made sure that my Mac gets a different range of IP addresses that it would get if it connected to the VPN (192.168.1.x vs. 10.0.0.x). Not using any VPN client -- just Network System Preferences. It has worked in the past -- but it was a while ago, so I can't pinpoint a change. My sysadmin doesn't even see incoming connections to the VPN (nothing logged about me when I connect). Looking for any diagnostic advice at all

Read the article

Alias wordpress folder from within another website

- by Bretticus

I have a little dilemma. I wrote a custom PHP MVC framework and built a CMS on top of it. I decided to give nginx+fpm a whirl too. Which is the root of my dilemma. I was asked to incorporate a wordpress blog into my website (yah.) It has much content and it's not feasible in the short amount of time I have to bring all the content into my CMS. Because of using Apache for years, I'm, admittedly, a little lost using nginx. My website has the file path: /opt/directories/mysite/public/ The wordpress files are located at: /opt/directories/mysite/news/ I know I just need to setup location(s) that targets /news[/*] and then forces all matching URI's to the index.php within. Can someone point me in the right direction perhaps? My configuration is below: server { listen 80; server_name staging.mysite.com index index.php; root /opt/directories/mysite/public; access_log /var/log/nginx/mysite/access.log; error_log /var/log/nginx/mysite/error.log; add_header X-NodeName directory01; location = /favicon.ico { log_not_found off; access_log off; } location = /robots.txt { allow all; log_not_found off; access_log off; } location / { try_files $uri $uri/ /index.php?route=$uri&$args; } location ~ /news { try_files $uri $uri/ @news; } location @news { fastcgi_pass unix:/tmp/php-fpm.sock; fastcgi_split_path_info ^(/news)(/.*)$; fastcgi_param SCRIPT_FILENAME /opt/directories/mysite/news/index.php; fastcgi_param PATH_INFO $fastcgi_path_info; } include fastcgi_params; include php.conf; location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; expires 30d; } ## Disable viewing .htaccess & .htpassword location ~ /\.ht { deny all; } } My php.conf file: location ~ \.php { fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_pass unix:/tmp/php-fpm.sock; # If you must use PATH_INFO and PATH_TRANSLATED then add # the following within your location block above # (make sure $ does not exist after \.php or /index.php/some/path/ will not match): #fastcgi_split_path_info ^(.+\.php)(/.+)$; #fastcgi_param PATH_INFO $fastcgi_path_info; #fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; } fastcgi_params file: fastcgi_connect_timeout 60; fastcgi_send_timeout 180; fastcgi_read_timeout 180; fastcgi_buffer_size 128k; fastcgi_buffers 4 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; fastcgi_intercept_errors on; Thanks, in large part, to @Kromey, I have adjusted my location /news/ but I am still not getting the desired result. I was able to learn to tack a ~ my /news location as I discovered that my php location was being matched first. With this setup, I now get a 200 status, but the page is blank. Any ideas?

Search Results

Search found 111890 results on 4476 pages for 'git update server info'.

Page 2079/4476 | < Previous Page | 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 | Next Page >

- by chmeee

- by BLaZuRE

- by Alex

- by user955664

- by Cleggy

- by levi

- by jabley

- by kedar karthik

- by David Hamilton

- by exhuma

- by user2118559

- by Jordan Messina

- by kce

- by user64566

- by Reid

- by arheops

- by user111196

- by Sola.Shawn

- by Notre1

- by AutoDMC

- by Manuel Sopena Ballesteros

- by Stu Thompson

- by sbrattla

- by Lou Franco

- by Bretticus

< Previous Page | 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 | Next Page >