Search Results

Search found 7139 results on 286 pages for 'auto vectorization'.

Page 209/286 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

• Unable to connect to server after a certain amount of time

  - by Troy

  I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

  Read the article

• Hard Drive Compatibility with Motherboard

  - by Wesley

  Here are the current specs to put things in context: ECS P4VXASD2+ V5.0 Intel Pentium 4 Northwood 2.8 GHz 2x 512MB PC2100 DDR266 SDRAM Maxtor DiamondMax 10 250 GB PATA (IDE) HDD Gigabyte 52x CD-ROM NVIDIA TNT2 Pro 16 MB OKIA 300W ATX PSU USB bracket Modem PCI Before, I actually had a 300 GB hard drive installed. However, I read the FAQ for the motherboard and discovered that a maximum of 250 GB hard drive was supported. So I ended up finding the one listed above and put that in. However, upon booting up, I reset the BIOS to defaults and auto-detected all the drives installed. The 250 GB came up as something like 251.0 GB. I didn't think much about it until I tried to boot up a Windows XP installation disc. It booted up successfully and run for about a minute before the computer randomly rebooted. I've made sure that all the jumpers and settings are correct and everything has been installed correctly. I've tried running it without the addons and one stick of RAM but still the same thing. What else could be causing this problem?

  Read the article

• Ubuntu 9.04: Ripping CDs with grip?

  - by chris

  I tried to rip a CD tonight, and couldn't figure out how to configure grip - /dev/cdrom doesn't seem to be the mount point for music CDs any more. How can I configure grip to find CDs? Update: /etc/fstab has /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0 But there's nothing visible in /media/cdrom0 (or /media/cdrom, which is a symlink to cdrom0) There's an icon on the desktop labeled "Audio Disk" and opening it shows the .wav files on the CD. The location is cdda://sr0/, but grip doesn't like that either. Trying to manually mount /dev/sr0, I get $ sudo mount -t auto /dev/sr0 foo/ mount: block device /dev/sr0 is write-protected, mounting read-only mount: you must specify the filesystem type Update 2: Tried to change the media handling preferences (From a file browser, Edit-Preferences, Media, CD Audio) to "Do Nothing". CD Still doesn't mount. Update 3: With an audio CD in the drive: $ ls -l /dev/ | grep cd lrwxrwxrwx 1 root root 3 2009-09-15 22:13 cdrom1 -> sr0 lrwxrwxrwx 1 root root 3 2009-09-15 22:13 cdrw1 -> sr0 drwxr-xr-x 2 root root 60 2009-09-15 22:13 pktcdvd lrwxrwxrwx 1 root root 3 2009-09-15 22:13 scd0 -> sr0 crw-rw----+ 1 root cdrom 21, 2 2009-09-15 22:13 sg2 brw-rw----+ 1 root cdrom 11, 0 2009-09-15 22:13 sr0

  Read the article

• Windows 7 Blank Screen on Boot / Login

  - by Greg

  I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

  Read the article

• NVidia TwinView - slow rendering on dual desktop

  - by lisak

  Hey, does anybody have experience with it ? I've set it up 4 times on 4 different machines. And there was always problems with slow rendering ( for instance : scrolling pages in browser is not fluent). But there always was something that finally made it work perfectly... I remember that one time this option helped, but not now Option "RenderAccel" "1" Nvidia geforce 8400GS or Zotac geforce 9500GT Monitors connected via dvi and hdmi connectors proper nvidia driver installed Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" Option "Xinerama" "0" EndSection Section "Files" ModulePath "/usr/lib64/xorg/modules" FontPath "/usr/share/fonts/local" FontPath "/usr/share/fonts/TTF" FontPath "/usr/share/fonts/OTF" FontPath "/usr/share/fonts/Type1" FontPath "/usr/share/fonts/misc" FontPath "/usr/share/fonts/CID" FontPath "/usr/share/fonts/75dpi/:unscaled" FontPath "/usr/share/fonts/100dpi/:unscaled" FontPath "/usr/share/fonts/75dpi" FontPath "/usr/share/fonts/100dpi" FontPath "/usr/share/fonts/cyrillic" EndSection Section "Module" Load "dri2" Load "glx" Load "extmod" Load "record" Load "dbe" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Acer AL1715" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 75.0 EndSection Section "Device" Identifier "Nvidia" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "MSI big bang-fuzion" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 8400 GS" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "RenderAccel" "1" Option "AllowGLXWithComposite" "1" Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "CRT: 1280x1024 +1920+0, DFP: 1920x1080 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• Changing the default boot option without losing the boot menu

  - by hvd

  I've had a working multi-boot setup with the Windows boot loader, containing menu items for two Windows 7 systems, and one for Grub. Grub in turn contains multiple menu items, but I think that's not relevant here. I've upgraded one system to Windows 8. When I now set a different system as the default, I lose the boot menu, and I lose the possibility of booting into the other systems. I've set Windows 7 as the default, rebooted, and get Windows 7, but I don't get to choose which system to boot into. I can run its own bcdedit to change the default back to Windows 8, and another reboot shows the boot menu again, but how can I avoid defaulting to Windows 8? Here are my current boot settings, is there anything that is misconfigured? C:\WINDOWS\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=F: description Windows Boot Manager locale nl-NL inherit {globalsettings} integrityservices Enable default {current} resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} displayorder {current} {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} toolsdisplayorder {memdiag} timeout 30 Windows Boot Loader ------------------- identifier {current} device partition=C: path \WINDOWS\system32\winload.exe description Windows 8 locale nl-NL inherit {bootloadersettings} integrityservices Enable recoveryenabled No allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \WINDOWS resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} nx OptIn bootmenupolicy Standard Windows Boot Loader ------------------- identifier {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} device partition=D: path \Windows\system32\winload.exe description Windows 7 locale nl-NL osdevice partition=D: systemroot \Windows resumeobject {59616f59-a2ba-11e1-b73a-806e6f6e6963} nx OptIn pae Default bootmenupolicy Standard hypervisorlaunchtype Auto detecthal Yes sos No debug No Real-mode Boot Sector --------------------- identifier {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} device partition=C: path \grub\winloader\grub.boot description Grub 2

  Read the article

• Issues Deploying Functional WAR to Elastic Beanstalk with Tomcat7

  - by BFar

  I am currently deploying OpenTripPlanner (http://github.com/OpenPlans/OpenTripPlanner.git) to Elastic Beanstalk. I'm able to successfully build and deploy opentripplanner with my own customized settings on an ec2. I have set it up so that the appropriate WAR file can be placed in the Tomcat/Webapps folder, and when Tomcat is started up, it will auto-deploy, and even download open trip planner's graph.obj from an S3. All of that works just fine, except when I try to deploy to Elastic Beanstalk. When I upload to Elastic Beanstalk, the log shows that my WAR file is successfully unpacked & successfully downloads the graph.obj from my S3. The only difference is that then nothing happens and I can't load the site in my browser. The health is RED, and I can't figure out what is going on. I've tried looking into ports and dns issues, but I can't determine what's wrong. Anyone have any ideas? Why would a WAR that works on tomcat7 outside of Beanstalk fail to be accessible?

  Read the article

• What is the reason for this DNSSEC validation failure of dnsviz.net?

  - by grifferz

  On trying to resolve dnsviz.net from a host using an Unbound resolver that is configured to use DNSSEC validation, the result is "no servers could be reached": $ dig -t soa dnsviz.net ; <<>> DiG 9.6-ESV-R4 <<>> -t soa dnsviz.net ;; global options: +cmd ;; connection timed out; no servers could be reached Nothing is logged by Unbound to suggest why this is the case. Here is the /etc/unbound/unbound.conf: server: verbosity: 1 interface: 192.168.0.8 interface: 127.0.0.1 interface: ::0 access-control: 0.0.0.0/0 refuse access-control: ::0/0 refuse access-control: 127.0.0.0/8 allow_snoop access-control: 192.168.0.0/16 allow_snoop chroot: "" auto-trust-anchor-file: "/etc/unbound/root.key" val-log-level: 2 python: remote-control: control-enable: yes If I add: module-config: "iterator" (thus disabling DNSSEC validation) then I am able to resolve this host normally. The domain and its DNSSEC check out fine according to http://dnscheck.iis.se/ so there must be something wrong with my resolver configuration. What is it and how do I go about debugging that?

  Read the article

• Can My Personal GMail Query A Remote LDAP Server?

  - by Maarx

  I have a personal GMail account, from which I frequently send e-mail to a great many various users of a specific business. The corporation has been kind enough to provide me with the credentials to access their LDAP server, with which I would like my GMail web client to be able to auto-complete partial addresses or names for which that LDAP server has an entry. Is there any way I can get a personal GMail account (or it's corresponding entire Google account) account to incorporate an LDAP server into it's Contacts? If I cannot get it to query dynamically and on-demand, is there an idiot-proof way (assuming the client permits, which they may not) to query the LDAP server for it's entire database, save it, and bulk import it to GMail? Perhaps, even, something I could set to repeat periodically (weekly, perhaps), without human interaction? If I did the latter, I assume it would be trivial to import all of these contacts under a single category that could be easily manipulated from within the GMail web-based client. I have been a staunch user and supporter of the GMail web-based client since it's instantiation, but this one is kind of a deal-breaker for me. If it's impossible, what do you suggest I do?

  Read the article

• Windows XP hanging on login screen

  - by Nathan W

  I have been given two Eee PC 100HA to manage for some people, they are both running the same hardware and XP home but one is having some strange problems with logging on. The main problem is that it hangs at the login screen for ages and sometimes never gets to the desktop. The strange thing is it only seems to do it after the computer has been cold started, but it won't do it if the computer has been restarted. I have made two logs of the start up with process monitor but every time the logger is attached the computer will log in fine. I have also set the computer to blue screen and create a crash dump when you press ctrl scroll twice but when I do it at the hung login it just sits at a black screen and I don't get a crash dump, I have turned off the auto system restart on failure option also. I can usually fix most computer start up and shutdown problems but this one has got me stuffed. Has anyone had the same problems before, or can recommend something that I can try? Cheers.

  Read the article

• How to keep subtree removal (`rm -rf`) from starving other processes for Disk I/O?

  - by David Eyk

  We have a very large (multi-GB) Nginx cache directory for a busy site, which we occasionally need to clear all at once. I've solved this in the past by moving the cache folder to a new path, making a new cache folder at the old path, and then rm -rfing the old cache folder. Lately, however, when I need to clear the cache on a busy morning, the I/O from rm -rf is starving my server processes of disk access, as both Nginx and the server it fronts for are read-intensive. I can watch the load average climb while the CPUs sit idle and rm -rf takes 98-99% of Disk IO in iotop. I've tried ionice -c 3 when invoking rm, but it seems to have no appreciable effect on the observed behavior. Is there any way to tame rm -rf to share the disk more? Do I need to use a different technique that will take its cues from ionice? Update: The filesystem in question is an AWS EC2 instance store (the primary disk is EBS). The /etc/fstab entry looks like this: /dev/xvdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2

  Read the article

• Xubuntu stuck after login

  - by viraptor

  How can I debug an issue with Xubuntu 12.04 (fresh install) which just waits idle after a login for about 30 seconds? The login screen is delayed correctly. After login, I get my desktop background, but no panels or auto-starting apps. It doesn't seem to be an authentication/pam issue, because I can login without delay at the console while the graphical session is still stuck. There's no disk or cpu activity and no obvious respawning of any process when I look at htop. There's nothing obviously wrong in .xsession-errors. Most interesting errors: openConnection: connect: No such file or directory cannot connect to brltty at :0 WARNING: gnome-keyring:: couldn't connect to: /tmp/keyring-wFn4VR/pkcs11: No such file or directory ... (polkit-gnome-authentication-agent-1:2131): polkit-gnome-1-WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The nam e org.gnome.SessionManager was not provided by any .service files ** Message: applet now removed from the notification area ** Message: using fallback from indicator to GtkStatusIcon ... (xfce4-indicator-plugin:2176): libindicator-WARNING **: IndicatorObject class does not have an accessible description. ... (xfce4-indicator-plugin:2176): Indicator-Application-WARNING **: Unable to get application list: Operation was cancelled Bootchart seems to end before I login, so it's not that helpful. Where else can I look for information?

  Read the article

• bind9 - forwarders are not working

  - by Sarp Kaya

  I am experiencing an issue with bind. If i want to resolve any domain name that is on the zone file. It works fine. However, when I try to resolve anything that does not belong to the zone file. I know that actual DNS servers that are being forwarded are working fine. But somehow bind9 fails to use them. The content of /etc/bind/named.conf.options is: options { directory "/var/cache/bind"; forwarders { 131.181.127.32; 131.181.59.48; }; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; I have also tried to use only one ip address and it still did not work. also the content of /etc/bind/named.conf is: include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; So there is no problem with including options file. Any recommendations for fixing this problem?

  Read the article

• dnsmasq Client TTL

  - by user548971

  I have a situation where my hosts file is constantly changing. Because of this I don't want clients to cache ip addresses resolved using the hosts file. Here is the command that starts dnsmasq for me: /usr/sbin/dnsmasq -K -R -y -Z -b -E -S 8.8.8.8 -l /tmp/dhcp.leases -r /tmp/resolv.conf.auto --stop-dns-rebind --rebind-localhost-ok --dhcp-range=lan,192.168.2.2,192.168.2.249,255.255.255.0,12h -2 eth0 In looking at this site: http://www.thekelleys.org.uk/dnsmasq/docs/dnsmasq-man.html I see that the -T option has this description: -T, --local-ttl=<time> When replying with information from /etc/hosts or the DHCP leases file dnsmasq by default sets the time-to-live field to zero, meaning that the requester should not itself cache the information. This is the correct thing to do in almost all situations. This option allows a time-to-live (in seconds) to be given for these replies. This will reduce the load on the server at the expense of clients using stale data under some circumstances. My command doesn't have the -T option. Do I need it or does dnsmasq default TTL to zero without it?

  Read the article

• Ubuntu server apt-get says "(-5 - No address associated with hostname)"

  - by Srini

  I have a ubuntu 12.04 server. Running sudo apt-get update on it produces errors like this: W: Failed to fetch http://au.archive.ubuntu.com/ubuntu/dists/precise-backports/main/binary-i386/Packages Something wicked happened resolving 'au.archive.ubuntu.com:http' (-5 - No address associated with hostname) I am able to ping all the other hosts on the network and also Google's DNS 8.8.8.8. But am unable to ping www.google.com. So, I'm guessing something is wrong with my DNS setup, but not sure what. I use static IP and my /etc/network/interfaces looks like this: auto eth0 iface eth0 inet static address 192.168.1.50 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.0.255 gateway 192.168.1.1 #dns-nameserver 203.12.160.35 203.12.160.36 #nameserver 203.12.160.35 203.12.160.36 My /etc/resolv.conf and /etc/resolvconf/resolv.conf.d/base are both empty and my /etc/resolvconf/resolv.conf.d/original says: nameserver 192.168.1.1 Any help would be greatly appreciated. P.S. I've googled it a bit and the common resolution is to switch to DHCP which I don't want to do since this is my home server. Thanks Srini

  Read the article

• Partition is missing in /dev

  - by haimg

  I'm having a strange problem since I moved from Centos5 to Centos6. I have three disks, first two are used as a RAID1, and third one is a stand-alone backup disk that is not listed in /etc/fstab (it is mounded when needed and then unmounted). My problem: After a boot, /dev/sdc exists but /dev/sdc1 does not. Also, the links in /dev/disks are also absent for the first partition of sdc. Disk itself is fine, and if I hot-remove it and plug it back in, /dev/sdc1 appears ok and everything is working. My question: What subsystem manages auto-discovery of disks, partitions, etc. during the boot process (e.g. what creates /dev/disks/by-label)? How do I configure it to scan /dev/sdc too and create all relevant files and links in /dev ? Edit: Here's the relevant part of dmesg output (the only place sdc appears). It does list sdc1, but it's not in /dev! sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdc: sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: DMAR:[DMA Read] Request device [00:1e.0] fault addr 361bc000 DMAR:[fault reason 06] PTE Read access is not set sdb1 sdb2 sdb3 sdc1 sda1 sd 1:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: [sdc] Attached SCSI disk sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk

  Read the article

• grub refuses to install to raid array

  - by ronno

  I have a software raid 0 setup with dual booting Windows 7 and Ubuntu 12.04. The GRUB bootloader that is already on the hard drive seems to work fine. However, since the latest package update for grub, it refuses to install the new version to the hard disk. grub-install throws the following error: /usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map. Auto-detection of a filesystem of /dev/mapper/< raid name_RAID0p9 failed. Try with --recheck. If the problem persists please report this together with the output of "/usr/sbin/grub-probe --device-map="/boot/grub/device.map" --target=fs -v /boot/grub" to < [email protected] update-grub pops the same "/usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map." every alternate line. I don't understand what exactly is going on. I'm afraid to reinstall the grub package because it might mess up the boot, which currently works fine. Is it safe to just ignore this?

  Read the article

• What is going on when I can't access an SMB server share (not accessible error) until I run cmdkey to delete the credential?

  - by Warren P

  I have a network connection share issue. The first connection works, and seems to stay connected for at least a few hours. However, after each time my windows 7 PC reboots, it can no longer form a network connection to the shared folder, nor browse to it, until I not only unmap and remap the mapped drive, but also, I have to use cmdkey to delete the stored credentials like this: cmdkey /delete:Domain:target=HOSTNAME My work PC is on a domain, and I am not the IT administrator, but I'm curious if there is anything I can do to investigate this issue. Any settings in registry or group policy that I could examine to see why the first connection works, but each subsequent attempt (once a stored credential exists) to browse or use the connection, fails with a connection error saying it is "not accessible", like this: I do not even get any error until at least several minutes go by. THe first thing I see is a window frozen and empty, and then I get this error: This has happened when connecting to a share on a DROBO device, and on a share which is not on the domain, but which was a Microsoft Home Server. I wonder if there's something broken in WIndows 7 professional with regards to connecting to non-domain shares when an active directory domain controller exists, and a particular workstation is joined to a domain? The problem only occurs if I click "remember credentials". It is not fixed by any amount of working with net use. Usingcmdkey to delete all stored credentials for the host is the only way to get back in, and it affects all non-domain shared folders. Update I'm hoping there are some registry locations I could check that could be misconfigured in some way that might explain why SMB/CIFS stored credentials for non-domain systems seem to be auto-invalidated in this weird way. Knowing how whacko Microsoft Windows domain and security handling is sometimes, this could be some kind of stupid "feature".

  Read the article

• Windows XP Disappearing Folders

  - by XenoFoxx

  I am researching a problem for a friend, and unfortunatly do not have direct access to his computer. I've tried to gather as much information as possible and I have researched it on various websites. I've not found anyone having the same problem my friend is having. So here goes: He has a media server in his home running Microsoft Windows XP. It has 3 drives, 1 for the OS and 2 for mass storage. Not long ago he went to access one of the mass storage media drives and it was empty, except for a single folder. His first assumption was that his roommate had deleted everything on the drive (excluding the remaining folder). He then checked the properties of the drive and it was still saying that the hard drive was nearly full. I told him to check the recycling bin, thinking that whoever deleted them didn't clear them from recycling and that they were still taking up space on the drive. My friend said the recycling bin was empty. So we have a drive that the windows file management system says is empty (again except for the remaining folder), but the properties of the drive say it's mostly full. Now it gets weirder My friend tried to create a new folder on this drive and it auto-named itself "New Folder(1)" which means that it recognizes there is already a "New Folder" in that directory. He tried to rename it to a name that he KNEW was there previsouly, and windows wouldn't allow it because it was a duplicate folder name. SO now it seems the folders are there, but not displaying in Windows Explorer. Both of us have no idea why this is occuring, why the folders vanished, why the one remaining folder didn't vanish, or how to make them visable again. Anyone else ever experience this? I can get more details if needed.

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• Magical moving desktop icons

  - by Nathan Taylor

  I have encountered a very strange behavior in Windows 7 that I cannot seem to identify and I have never seen or heard of on any system configuration. Whenever I move my mouse to the left-most edge of my primary display (centered in 3-display setup), my desktop icons magically move away from the cursor (up or down and to the right). It only happens when my desktop has focus and the mouse is positioned on the left, top or bottom edge of the main display. Moving the mouse all the way to the right edge of my right secondary display causes the mouse icons to snap back into their correct position. Ridiculous video of the issue My setup is 3 displays on two display adapters. The main display is running at 2560x1600, connected to the machine via a USB-powered DVI-D to DisplayPort adapter and is driven by an NVIDIA NVS 3100M video card. The secondary displays are running at 1440x900 and 1200x1920 and are driven by integrated Intel HD Graphics (mobile). It seems like some kind of panning behavior, but it's obviously not working as expected. I have updated all of my drivers, but no change. It's probably worth noting that the desktop icons are set to auto-arrange.

  Read the article

• Permission denied (publickey,gssapi-with-mic,password) ssh error

  - by zentenk

  Heads up I'm a noob with linux and networking. I set up a ubuntu server and I have a static ip for my network. When I try to connect to the server at home (external), it prompts me to log in. I supply the correct password (or incorrect pw), I get the error Permission denied, please try again. and after 3 times I get Permission denied (publickey,gssapi-with-mic,password) I am however able to connect with SSH from another computer in the same network with ssh < internal ip of server > I'm connecting with mac os x and my config file is vanilla. Note: During installation of ubuntu it says I don't have a default route or something while doing auto network configuration, but I ignored it and continued the installation, could this be the problem? EDIT: I have tried the below, I have nothing in hosts.allow and also iptables shows the ports that I have allowed, which is 22. I checked the auth.log, and there is nothing when I connect to it remotely (even when it says permission denied). I have tried connecting to it internally and the correct authentication logs show. Any idea whats wrong?

  Read the article

• Debian Wheezy (testing) df reported volume size

  - by TheRoadrunner

  I am a bit confused about the /dev/sda* references since I installed Wheezy instead of Squeeze on a testing box. fdisk -l returns: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e9623 Device Boot Start End Blocks Id System /dev/sda1 * 2048 480278527 240138240 83 Linux /dev/sda2 480280574 488396799 4058113 5 Extended /dev/sda5 480280576 488396799 4058112 82 Linux swap / Solaris This seems correct. But df -h /dev/sda (and /dev/sda1 and /dev/sda2 and /dev/sda5) returns: Filesystem Size Used Avail Use% Mounted on udev 10M 0 10M 0% /dev The same happens with every entry under /dev/disk/by-id and /dev/disk/by-path. Only one of two entries under /dev/disk/by-uuid returns the correct volume size: df -h /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 Filesystem Size Used Avail Use% Mounted on /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 229G 22G 196G 11% / Contents of /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda1 during installation UUID=cacdbad6-7e6b-4e80-84ba-e3c77ef48796 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=45840d13-ee36-4e77-8e73-16cbdff25eb1 none swap sw 0 0 /dev/sr0 /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0 It seems all other references than the uuid points to the swap partition. Is this because Wheezy is in testing, and should it be reported as an error?

  Read the article

• What Windows app can sort a huge XML file?

  - by Torben Gundtofte-Bruun

  I have some enormous XML-based configuration files, with 125000 lines in them. The problem is that they are auto-generated by the system I use, and "child" tags are in a random order within their respective parent tag. This means that a diff comparison is impossible. I want to recursively sort all tags within a parent tag by the value in name="". Some parent tags only appear once and don't have a name="" parameter; these should be sorted by the tag name itself. Once the files are sorted like this, they can be compared quite easily using normal tools. We are currently using ExamXML which can match unsorted XML files, but it fails because the files are too big. Is there an application that can do this? (Windows much preferred; Linux only as a last resort) I do not want to dive into development or XSLT jobs. I am thinking that someone must have made a simple sorting tool like this already - I just can't find it using Google. Update: With help from this site, I created a small package that I want to share: XML-Sorter_v0.3.zip Update: Follow-up question here.

  Read the article

• Remote network traffic not passing through VPN

  - by John Virgolino

  We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

  Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >