Search Results

Search found 6176 results on 248 pages for 'wireless encryption'.

Page 209/248 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

  • Web browsing is fast, but downloads are slow

    - by Ricket
    I work for a company on my university's campus, helping with general IT problems and some web development. But lately there has been a problem that has me and my boss completely stumped. We, plus one contractor, make up the entire IT department, so I'm reaching out to you for help. All around the office, we have wall jacks. These collect in a closet down the hall and all plug into a switch. This switch, along with our individual server jacks, plugs into another switch, and that switch plugs into our firewall hardware. Then the firewall is connected out to our campus network. Our campus internet is, well, very fast. I don't know exactly the terms, tiers, etc., but we have thousands of students and downloads can run as fast as 10 MB/s at night; uploads are sometimes even faster. I think we're practically ISP level. In short, I have a lot of faith that it is not the campus side of things that is causing a problem, combined with other evidence I'll mention in a moment. So our symptoms: web browsing is fast. Web pages, images, etc. load instantly. No problems there. But then when I go to download something, the download starts fast but very quickly (a matter of seconds) drops to nearly 0. Often it will actually drop to 0 and time out. This happens with even very small files, 1 MB or less. It smells to me like a QoS sort of thing. I'm not entirely sure, and I wanted to get your opinions first. My boss is hesitant to touch our firewall, much less let me touch it, and it was set up and is managed by a consultant remotely. These problems don't seem tied to a time of the day. I've tried downloads after 5:00 and still the same thing happens. From my desk, I can turn on my wireless adapter and pick up the campus wireless access point. If I unplug ethernet and connect to it, downloads are fast. This adds to my suspicion that it's limited to our company network. Also, a number of weeks ago the consultant upgraded our firewall firmware. Suddenly everything was very fast. I tested with downloads from Sun and speedtest.net and things were blazing fast, as they should be with our campus internet! It was wonderful, and I figured the slow speeds were an old firmware bug. In a matter of days, things steadily declined until they were back to the old symptoms. Oh, and we have antivirus installed on every computer, and we keep it up to date. Though I suppose the possibility is still there that someone could have spyware which is bogging down our internet, in which case what is the easiest/best way to find this out? (maybe this should go in a separate question) Thank you for your patience in reading all of this. Do you have any ideas as to what I can try? Is this something that you've experienced before? What sort of tools or methods can I use to try and diagnose the problem? P.S. everything here is Windows. Windows Server 2003 and 2008 on our servers, and Windows XP on employees' machines. Update: We are submitting a ticket to the university to just take a look and see if they see anything unusual and/or can suggestion methods for us to try and pinpoint our problem. Hopefully they'll be helpful! I'll update this to let you know what goes on. Update again: We found a hub (yes, a HUB) right between our campus connection and our firewall. It had only those two ethernet cables plugged into it, nothing else. After removing the hub, our speeds have jumped up to several mbps. However in talking with the campus, we got them to run a gigabit line to our firewall in place of the 100mbps line. As of friday, we are at about 65 mbps up and down (according to speedtest.net at 8am)!! Go NC State!!

    Read the article

  • How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

    - by Senseful
    I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

    Read the article

  • Seasgate GoFlex NAS + Horrible Speed = Bad Experience

    - by Jon H
    I am having issues with transfer speeds from my desktop PC to my NAS. I have my NAS hooked up to a Gigabit Gateway as well as my Desktop with Cat 5e. I see up to 4.0 MB/Second Transfer Rates, the normal is about 2.5 MB/Seconds. There is 3 Partitions on my NAS, Public, Private, Backup. When I transfer from Private to Public I see the speeds above. If its under the same partition almost instant. I was wondering if the speeds I am seeing is in due to my Computer or the NAS. I was looking into building my own Media Server in due to these horrible speeds. Is their anything I can do in the mean time to speed this up? Motherboard = M3970AM-HP (Angelica) Processor = AMD FX 6100 Ram = 10GB PC3-10600 MB/sec Hard Drive (1) = 1.5TB SATA 3.0GB 5400RPM Hard Drive (2) = 120GB SATA SSD NAS = Seagate 3TB Go Flex Home Connection (1) = 1000 Base T Connection (2) = Wireless N

    Read the article

  • Could local ISP capture my location whenever i launch a VPN to a VPN server?

    - by Ozgun Sunal
    I am extremely concerned that my ISP collects any information once I am connected to a VPN server. For instance, as far as I know, when I start a connection to a HotSpotShield VPN server, an IP address is assigned to me just before a successful connection. Besides, I'll be having an extra IP address at the beginning with the TAP Adapter. An encryption tunnel is set up between me and the VPN server. Whenever my request for a website reaches them (VPN server), they decrypt the data and later they encrypt the reply which returns from the web (targeted) server. This works like that. So, the ISP can not see what I am watching, displaying and writing because the connection is encrypted. But, the targeted websites see and record all actions. Still, they can not identify my real IP address. I'm really concerned about if the ISP can see "my location". OK, it has an IP address from another country as my real IP address, but how does my ISP detect the traffic going through them? Can they find out who I am? Won't they say "Hey, there is a traffic but who is and what he is doing right now?", because I get the Internet from them?

    Read the article

  • How to use my computer to control a lamp?

    - by nona urbiz
    I've been researching computer automation systems, but everything I've found has been overkill for what I'm interested in. Can anyone help me control a lamp that is on my desk, plugged in the wall beneath the desk, with my computer (also on the desk, usually). What got me thinking is that I have the lamp plugged into a Belkin extension cord/surge protector that came with a wireless switch that toggles the power going to 6 of the eight sockets. Can I somehow hook my computer into this? I'm not too afraid to get into some wiring type thing, but do have a somewhat limited budget. It'd also be cool to get a dimmer in the loop too. thanks aha. after more research, i have realized what i'm looking for is instructions for a DIY version of this that won't look so ugly, and that i can build a UI for rather than shortcuts.

    Read the article

  • 64 Bit Windows drivers for Inspiron 1720

    - by Rob Allen
    Dell doesn't seem to offer 64 bit drivers specifically for the Inspiron 1720 (laptop). I'm going to be upgrading from Vista 32-bit to Windows 7 64bit and I want to pull down the necessary stuff before hand. Are there any Dell systems that are similar enough to the Inspiron 1720 that I can use for a baseline to make sure I still have Ethernet and WiFi after the reinstall? It doesn't matter if they are for Vista 64 or Windows 7. Identified hardware: Processor: Intel mobile Core 2 Duo T7500 Chipset: Intel Mobile 965 Express Wifi: Intel Pro Wireless Drive Controller: Intel Matrix Graphics: nVidia GeForce 8600M GT Bluetooth: Dell TrueMobile 355 + EDR Ricoh card reader I think anything else, the default Windows drivers will be sufficient. Let me know if you think I missed something thing please.

    Read the article

  • Create access point (uap0) on debian 7(arm) - not found?

    - by ethrbunny
    I'm working with a fanless PC that has an ARM chipset, 2 eth plugs and a wifi card (among other things). If I install debian 6 on it all three network interfaces are available at boot time. Today I tried to install debian 7 and had numerous errors indicating that the wireless card isn't supported. uap0: error fetching interface information: Device not found SIOCSIFADDR: No such device uap0: ERROR while getting interface flags: No such device uap0: ERROR while getting interface flags: No such device No such device ERR:UAPHOSTCMD is not supported by uap0 ERR:Command sending failed! No such device ERR:UAPHOSTCMD is not supported by uap0 ERR:Command sending failed! I've tried comparing the kernel module list to the working system but there are too many other differences to make something obvious enough (to me) stand out. How would I get started debugging this problem?

    Read the article

  • Linux Bridge, Samba netbios name/hostname access

    - by Christopher Wilson
    I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

    Read the article

  • Can a device (WAP or switch) be configured as an 802.1x supplicant?

    - by Allan Ross
    We are looking at implementing 802.1x on a wired/wireless network. What I am looking for is a device that can act as a supplicant and once authenticated on the network, is able to pass traffic from any downstream connected device. The point of doing this would be to allow a properly pre-configured device to be provided to a client user who could then connect any device on the downstream side of the device. We will be able to manage the aggregate traffic on the device without concern for what is connected on the far side. Am I dreaming; does every device out there support this and I just don't know it or is reality fall somewhere in the middle?

    Read the article

  • wireshark not seeing all packets on WiFi

    - by Caffeine Coma
    I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

    Read the article

  • What causes Windows Boot to stall?

    - by Nick Berardi
    For about 6 months now I have been having this weird problem where Windows 7 fails to fully boot correctly. What happens is this. Starting Windows shows up on the screen. Then 3 out of 4 times nothing else happens, no Windows Flag animation, just nothing occurs. After 3 or 4 restarts repeating steps 1-2 above, the Windows Flag animation finally shows up and everything works as expected. My question is what is causing this problem in steps 1 and 2? Because I have tried the following with no luck: Error checking and correcting of any disk errors Updating drivers Doing a clean install of Windows 7 My setup is as follows: Windows 7 64-bit Ultimate 8 GB RAM 128 GB Crucial SSD (firmware 0005) Dell Latitude E6410 Intel Wireless and Graphics Other than what I have tried above I am totally out of ideas and looking for some new ones to try.

    Read the article

  • Tunneling a public IP to a remote machine

    - by Jim Paris
    I have a Linux server A with a block of 5 public IP addresses, 8.8.8.122/29. Currently, 8.8.8.122 is assigned to eth0, and 8.8.8.123 is assigned to eth0:1. I have another Linux machine B in a remote location, behind NAT. I would like to set up an tunnel between the two so that B can use the IP address 8.8.8.123 as its primary IP address. OpenVPN is probably the answer, but I can't quite figure out how to set things up (topology subnet or topology p2p might be appropriate. Or should I be using Ethernet bridging?). Security and encryption is not a big concern at this point, so GRE would be fine too -- machine B will be coming from a known IP address and can be authenticated based on that. How can I do this? Can anyone suggest an OpenVPN config, or some other approach, that could work in this situation? Ideally, it would also be able to handle multiple clients (e.g. share all four of spare IPs with other machines), without letting those clients use IPs to which they are not entitled.

    Read the article

  • Using URL rewrite module for http to https redirect

    - by johnnyb10
    Following ruslany's suggestion on the URL Rewrite Tips page here, I'm trying to use URL Rewrite to redirect http:// requests for my site to https://. I've written and tested the rule using a test site I set up, and so now the final piece is to create a second site (http) to redirect to my https site. (I need to use a second site because I don't want to uncheck the "Require SSL encryption" checkbox on my existing site.) I'm an IIS newbie so my question is: how do I do this? Should I create a site with the same name and host header, only it will be bound to http? Will IIS let me create a site with the same name? I don't want to screw anything up with my existing site (which is a SharePoint site, currently used by external users). That site currently has http and https bound to it. So my assumption is that, using ISS (not SharePoint), I will create a new site (http only) with the same name and host header as my existing site, and add the URL Rewrite rule to the http site. And then I guess I should remove the http binding from my existing site? Does that seem correct? Any advice, gotchas, etc., would be appreciated. Thanks.

    Read the article

  • Can't bring NAT to work

    - by user31738
    Hello, I bought a D-link DIR-300 wireless router and i can't bring NAT to work, i have an ssh and http service i need to forward to the internet. My connection is as follows: I have an ADSL connection, i'm using a ADSL ethernet modem connected and working, it doesnt let me put it on bridge mode. I have my router connected to my adsl modem through ethernet, it gets its ip through DHCP (and i'ts always the same) I have a desktop computer running linux with apache and openssh configured and working, it has fixed ip. I configured the NAT in the modem forwarding port 22 from the router ip to the internet. In the router i setup NAT forwarding port 22 from the desktop computer fixed ip to out there. This setup already worked with a fonera i had before, can anyone help me with this or tell me what kind of tests do i need to do? How can i test if the router is forwarding ports correctly before the modem?

    Read the article

  • How to show disconnect network drives

    - by Jake
    Windows 7 and Vista laptops in my company domain has network drives set up by Win2k8 Server GPO. Normally, when the laptops has ethernet cable plugged in before boot, the network drives connect and appear as expected at the end of startup sequence. However, when the laptop has ethernet cable unplugged, the network drives are not connected, which is fine, but the disconnected icons disappear as well. i.e. the drives are not set up. At the end of the startup sequence, upon reaching desktop, the wireless adapters will connect to the network and the laptop will be able to find the network drive. Hence I want the drives to be setup nonetheless, so that the next attempt to connect, say, via a desktop shortcut, will reestablish the network drive connection. How can this be done?

    Read the article

  • Windows 7 Professional Cannot Connect to Share - Wrong password

    - by henryford
    I know that this question has actually been asked a few times before, but every solution I found didn't yield any results on my end, I can't get my head around it: When I am trying to connect to a share on the network, I always get the response "The specified network password is incorrect". However, the password is definetly correct and it works if I connect from another machine. I changed the LAN Manager authentication level to "Send LM & NTLM - use NTLMv2 session security if negiotated", I configured Kerberos encryption types to include all suites, rebooted (several times), but still - no luck. I can connect if I use my regular account with which I am logged in, but I need to connect with a different user since my log-in user has not enough privileges on the share. When I do that, the error above comes up. I'm really frustrated at the moment, this problem is driving me crazy. I'd be gladful for any possible solution to this. At the moment I'm using a workaround: I connect to a different machine via RDP, login with the user I have to use for the network-share connection and then I can map the drive and copy/paste from the RDP session to my local workstation. This is also working when I am connecting via RDP with my current login user and map the drive with the other user who has sufficent privileges. Tanks in advance, Thomas

    Read the article

  • Recommending simple appliance for DansGuardian, iptables, snort inline

    - by SRobertJames
    I'm currently using a Linksys E2000 with dd-wrt. I'd like to add DansGuardian for Content Filtering and snort-inline for IPS; but those require a more powerful box (mainly, more storage). Can you recommend a good device to use? I'm open to both overwrite-the-firmware (like dd-wrt) and designed-to-be-customized boxes. Requirements: 1. 5+ Ethernet ports, pref. GigE 2. small form factor 3. No noise (office environment) 4. low power 5. Not sure about 802.11 wireless Budget < $400, pref. less.

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - Setup guide recommendations?

    - by Peter Mounce
    I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. My ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • Using URL rewrite module for http to https redirect

    - by johnnyb10
    Following ruslany's suggestion on the URL Rewrite Tips page here, I'm trying to use URL Rewrite to redirect http:// requests for my site to https://. I've written and tested the rule using a test site I set up, and so now the final piece is to create a second site (http) to redirect to my https site. (I need to use a second site because I don't want to uncheck the "Require SSL encryption" checkbox on my existing site.) I'm an IIS newbie so my question is: how do I do this? Should I create a site with the same name and host header, only it will be bound to http? Will IIS let me create a site with the same name? I don't want to screw anything up with my existing site (which is a SharePoint site, currently used by external users). That site currently has http and https bound to it. So my assumption is that, using ISS (not SharePoint), I will create a new site (http only) with the same name and host header as my existing site, and add the URL Rewrite rule to the http site. And then I guess I should remove the http binding from my existing site? Does that seem correct? Any advice, gotchas, etc., would be appreciated. Thanks.

    Read the article

  • if an outdated, vulnerable but clean Windows machine is connected to network behind router, can it be detected and attacked?

    - by EndangeringSpecies
    suppose the machine is clean of all malware but not in any sense updated, patched, secured etc. Suppose I connect it to the internet from behind wireless router with the intent of using it only on a few trusted sites and only there. Or, for the sake of argument, maybe I wouldn't do any browsing at all, just let it sit there connected to the network. This is all happening in a residential situation with cable internet. In this situation can a remote attacker somehow detect the fact that the machine is connected to the internet and try connecting to do an exploit?

    Read the article

  • How to identify cause of system lock on debian squeeze?

    - by David Sanders
    I have a desktop system at work with debian squeeze installed. Every couple days or so, when I come in in the morning, the system appears to be asleep and won't wake up. I suspect it goes into power save mode and then doesn't receive the wake up signal when I click the mouse or touch the keyboard. Does anyone know where I should look in order to start tracking this down? Like log files, etc? I doubt it, but maybe the fact that I'm using a mac aluminum usb keyboard and a wireless usb mouse (that has an off switch) has something to do with it? Maybe, when I turn my mouse off at the end of the day, the system loses track of the device somehow? I dunno :P. Thanks in advance.

    Read the article

  • Accessing Windows from Linux/Mac by name using TCP/IP

    - by stevekuo
    What are some solutions to access Windows by its computer name from Linux and Mac using TCP/IP. That is, from terminal I want to be able to ping my Windows PCs using its host name. My setup is: Various machines running Ubuntu, Windows XP and OS X. Networked using a consumer grade wireless router which provides DHCP. The only DNS is the ISP's, which resolves Internet names and not local host names. The Windows machines can ping each other by name. The Ubuntu and OS X machines can only ping Windows by IP address (name doesn't work).

    Read the article

  • Not able to access other machines on network

    - by TheVillageIdiot
    Hi I'm running Windows 7 Enterprise (32bit) on my laptop. For some time I'm not able to access other machines using \\192.168.xxx.xxx. I've installed VM Ware player on my machine few days back but I don't remember if it happened just after that or there is some other reason behind it. EDIT:- I've disabled VMWare Bridge Protocol but still no effect. Please help me. PS:- I've used both wireless and wired networks. Network sharing is enabled and I can ping other machines but cannot access network shares. I get following message: \\xxx.xxx.xxx.xxx You might not have permission to use this network resource. Contact the administrator of this server to find out if you have acess permissions. The request is not supported. EDIT (2):- Network Discovery, File and Printer Sharing, Folder sharing are all on.

    Read the article

  • 2wire modem to linksys router

    - by Imajica666
    I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

    Read the article

  • Can't ping self

    - by Paddy
    I have a wireless internet connection setup on my Mac. (v10.5.6) Am connected to the internet and everything is running smoothly. I recently discovered a quirky behaviour while setting up apache web server. When i typed in my dynamic ip (http://117.254.149.11/) in the webbrowser to visit my site pages it just timed out. In terminal i tried pinging localhost and it worked. $ ping localhost PING localhost (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.063 ms 64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.056 ms 64 bytes from 127.0.0.1: icmp_seq=2 ttl=64 time=0.044 ms But if i pinged my ip it would just time out. $ ping 117.254.149.11 PING 117.254.149.11 (117.254.149.11): 56 data bytes ^C --- 117.254.149.11 ping statistics --- 10 packets transmitted, 0 packets received, 100% packet loss Pinging any other site works though. I am completely stumped. Any help would be greatly appreciated.

    Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >