Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 211/783 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• Is it possible to open server ports on TUN devices?

  - by JosephH

  If I make a VPN connection to a server (say myvpn.com; assume this server is not behind any router/firewall) via a TUN device and open a port (say 5555), will someone else be able to connect to me via myvpn.com:5555? If not, is there a tunneling software that does exactly this in a transparent manner? i.e. run any TCP/UDP-based server instance behind a router without NAT using another remote server.

  Read the article

• Finding spoofed IP address on network

  - by Jared

  I have a few IP spoof dropped messages coming out of my Sonicwall firewall, we'll call them Source A and Source B. Both of these sources have the same mac address indicating they're coming from the layer 3 switch behind my firewall. Source A has an ip within a valid subnet on my network and it shows up in the ARP table of my layer 3 switch. I was able to trace the exact location and fix the issue. Source B's ip however, is not within valid subnet on my network and it's not showing up in my layer 3 switches arp table. Any idea how I can trace the location of this device within my network? Thanks in advance.

  Read the article

• RouterLess, house-wired network using multiple powerline adapters

  - by Cliff Arnell

  related to the 'old days' of one ethernet cable tapped with Ts for each monitor.... my question might be very simple... or not. I have an over-the-air internet provider with a wire dish with a powered transceiver and cat5 cable out of the providers supplied modem. I'm presently connecting the output of the modem into my wireless router which sends the internet signal all over the house. Standard stuff, I believe. My Question. Can I just connect the output of the modem into 1 powerline adapter and tie all my equipment such as computer, printer, laptop, Tivo recorder, etc. into 1-each local powerline adapters located near each devices resulting in a 'house-wired' network and no router? I'm bothered by the idea that my over-the-air provider might be using something in my router to establish and keep my IP connection alive. I did have to configure the router for my IP, a router which, in my proposed scenario, would no longer exist. Thank you for your help.

  Read the article

• Speed up file access on home network

  - by kurasa

  I have 2 PCs (Windows 7 Ultimate) and a Mac running Windows 7 using vmware fusion on my home network tied together using WRN1000 NETGEAR Router On one of the PC's I have a set of file (MYOB .myo). These use a data source to access the data in the files. Operations (reading,writing) to the .myo on the PC which hosts the files is fine but the other 2 it is painfully slow/unreliable and I am wondering what I can do to speed this up. Some ideas I have are 1. Turn off the Windows firewall on all the windows installations on the home network 2. Buy another router. Specifically a router which I can connect a USB flash drive on the back where I can put the .myo files and all the PC can access the files from the USB flash drive on the router (does this speed things up?) Any advice greatly appreciated on how I can speed up this access to data

  Read the article

• Linksys WiFi usb dongle and linux woes

  - by MrStatic

  I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

  Read the article

• CISCO Router configuration

  - by Acharf

  Hey, I'm looking for a course of CISCO Commandes to configure a router. Is there anyone that can help ?

  Read the article

• Router drops internet connection if I connect an additional pc

  - by BluePerry

  Hey, I'm using a SMC2804WBRP-G router connected to my ADSL-modem. Usually there are two computers connected to this router: a win7 ultimate desktop(wired) and a macbook air (wireless). Both working absolutely fine and never caused any connection drops as far as I know. A new room mate moved in last month and each time she starts up her win7 home laptop the router looses the internet connection. The laptop is on a wired connection. The first time she connected to my router, the connection dropped every 2 mins. To find out whats wrong with her machine I disabled all unnecessary services etc. besides the anti virus software. That helped to eliminate almost all of those periodic connection drops. But the start up drop remained and I've got the feeling that the router is still loosing connection from time to time. I haven't had the time to find out what service caused the periodic drops. But I'm more concerned about is that start up drop. Can anyone point me in the right direction to look for the problem? I would be very thankful for any hints or tips!

  Read the article

• Choosing a home network layout

  - by James M.

  I have a server, 4 PC's, a network printer, a switch and an ADSL modem. Currently the server runs Red Hat 9 and sits between the internet and the other PCs like in http://upload.wikimedia.org/wikipedia/en/1/12/Sample-network-diagram.png I have bought a new server PC to replace the old one, and I plan to install Fedora Core linux on it. The server acts as web and file server. The PCs all run Windows. Alternatively, I could connect the new server and all PCs to the switch, and connect the switch to the modem. (Sorry, couldn't find an image.) What are the pros and cons of these network layouts? Eg. in terms of reliability, security and flexibility? I am not a Linux guru but know of (and am not afraid of) iptables, dhcpd et al. Thank you for any tips, pointers and links.

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• RJ45 female to male fault

  - by GeoPhoenix

  i have the following - common - problem, on one end of the cable, there are RJ45 males T586 A which are connected to a 8-port switcher, on the other end, there supposed to be RJ45 females _T586 A which in turn will allow another RJ45 male to be connected. the commonly used color scheme was followed on males (having the head down) blue white blue orange white green green white orange brown white brown the problem i believe is located on female end of cable, which i try multiple time to follow the numbers designated by the module, which is the list above in reverse, and as listed resulting in no signal transmission. tried the T586B (both ends) for device to device once, but no results. Which is the proper way of handling this wiring? There were also additional RJ45 females with the numbers 6-5-4-3, but 1 to 8 isn't supposed to be used for this?

  Read the article

• Flow of packet in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN. When packet goes from router to local LAN, do it passes all the computers? Means did it goes to ehernet card of every computer and those computers accept the packet based on their physical address. To which pc the packet will go first? To the nearest to the router? What happen if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this? Thanks in advance.

  Read the article

• Prevalence of WMI enabled in real Windows Server networks

  - by TripleAntigen

  Hi I would like to get opinions from systems administrators, on how common it is that WMI functionality is actually enabled in corporate networks. I am writing an enterprise network application that could benefit from the features of WMI, but I noted after creating a virtual network based on Server 2008 R2, that WMI seems to be disabled by default. Do systems admins in practical corporate networks enable WMI? Or is it usually disabled for security purposes? What is it used for if it is enabled? Thanks for any advice! MORE INFO: I should have said, I really need to be able to query the workstations but I understand that by default the WMI ports on Win7 and XP firewalls (at least) are disallowed, so do you use some sort of group policy or other method to leave a hole open for WMI on the workstations? Or is just the servers that are of interest? Thanks for the responses!!

  Read the article

• Please recommend tools for PC, browser, home network performance problems?

  - by mobibob

  My client is experiencing some odd response behavior in their browser for the past few days. Classic, "nothing has changed" so I am starting at ground zero. Browsing a website will timeout or take a ridiculous time to load -- other times, the same site and query is immediately responsive. Once a connection is established, video streams are uninterrupted. The home network hosts a website, but it is not experiencing any activity in Apache's 'access.log' I am using speedtest.net to check if the ISP through the internet is 'OK' -- which looks typical (average +/-). I have to suspect the home network is beaconing or something very abnormal, but I don't know where to start.

  Read the article

• Under FreeBSD, can a VLAN interface have a smaller MTU than the primary interface?

  - by larsks

  I have a system with two physical interfaces, combined into a LACP aggregation group. That LACP channel has two VLANs, one untagged (the "native vlan") and one using VLAN tagging. This gives us: lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether 00:25:90:1d:fe:8e inet 10.243.24.23 netmask 0xffffff00 broadcast 10.243.24.255 media: Ethernet autoselect status: active laggproto lacp laggport: em1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> vlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=3<RXCSUM,TXCSUM> ether 00:25:90:1d:fe:8e inet 10.243.16.23 netmask 0xffffff80 broadcast 10.243.16.127 media: Ethernet autoselect status: active vlan: 610 parent interface: lagg0 Is it possible to set a 9K MTU on lagg0 while preserving the 1500 byte MTU on vlan0? Normally I would simply try this out, but this is actually on a vendor-supported platform and I am loathe to make changes "behind the back" of their administration interface. This system is roughly FreeBSD 7.3.

  Read the article

• How to find on the Windows 7 who and when use(d) a certain share?

  - by John Thomas

  We have a workstation using Win7 on a LAN with a domain. On that workstation we set up some network shares. Can we find who used (user name and/or computer name) and when the shares? Note that we know about Computer Management System Tools Shared Folders Open Files. We don't want to see so much real-time who's using the shares but we are interested more in a logging solution, ideally interpreting / using the data from Win7's Event Viewer.

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Why does 1GBit card have output limited to 80 MiB ?

  - by Gallus

  I'm trying to utilize maximal bandwidth provided by my 1GiB network card, but it's always limited to 80MiB (real megabytes). What can be the reason? Card description (lshw output): description: Ethernet interface product: DGE-530T Gigabit Ethernet Adapter (rev 11) vendor: D-Link System Inc physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 11 serial: 00:22:b0:68:70:41 size: 1GB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation The card is placed in following PCI slot: *-pci:2 description: PCI bridge product: 82801 PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: 92 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list The PCI isn't any PCI Express right? It's a legacy PCI slot? So maybe this is the reason? OS is a linux.

  Read the article

• How do I access my samba drive through several layers of network topology?

  - by stephenmm

  I have a new windows 7 Home Premium machine that is in a different room than my main computer area. As such I have to use a bridge and another router. Everything is working wonderfully except I cannot access the SAMBA drive with the new machine. I know that SAMBA is accessible as an older WinXP machine can access it. A picture of my network would probably be helpfull: To ISP | | +---------------------------+ | WAN | | Cable Modem | | (2WIRE678) | | | | | +---------------------------+ | +---------------------------+ | | (|) (|) +-----------+ | Belkin Router | | | | Wireless | | (F5D) |--+ +--| WinXP | | | |SAMBA USER | | | +-----------+ +---------------------------+ | | | | +------------+ | | Ubuntu | | | Apache + | | |SAMBA Server| | +------------+ | | +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ # # +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ | +---------------------------+ | | | D-Link Router | | (DI-524) | | | | | +---------------------------+ | | | | +-----------+ | | | Win7 | |SAMBA USER?| +-----------+ More interesting data points: 1. I can ping the SAMBA server from the Win7 machine locally (Ie. 192.168.2.2) 2. I can access the webserver from the Win7 machine locally (Ie. 192.168.2.2) 3. I followed the advice to get Win7 and SAMBA to play nice: http://www.tannerwilliamson.com/2009/09/windows-7-seven-network-file-sharing-fix-samba-smb/ Sorry for being so long winded but it is kind of complex and I am really at a loss as to how to fix it. If any of you have some suggestions I would love to hear it!

  Read the article

• Network backup for Macs and PCs - formatting question

  - by neilfein

  I'm trying to use a LaCie 2TB drive as an AirPort drive, for backup on a home network. We have one mac and two PC laptops. My plan is to create a Mac partition and a Windows partition. However, Disk Utility won't let me set the windows partition to Windows format; there's no option in the menu for it in the partition tab. Am I doing something wrong? Alternatively, is there a way to partition the drive with one partition that all three machines can see? We have a Mac G5 with 10.4 and two laptops with Windows 7. Thanks!

  Read the article

• ipconfig /release not working, why?

  - by barlop

  ipconfig /release is not working, why is that? here is a sequence where I put my cable in get an IP, try ipconfig /release and it tells me it can't release wireless, but there is no wireless connection. i'm just trying to release the wired one. C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Fine so I plug my cable in C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 0.0.0.0 Subnet Mask . . . . . . . . . . . : 0.0.0.0 Default Gateway . . . . . . . . . : C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.8 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.254 Fine so from above, it clearly has an iP C:\>ipconfig /release Windows IP Configuration No operation can be performed on Wireless Network Connection while it has its me dia disconnected. C:\>

  Read the article

• how're routing tables populated?

  - by Robbie Mckennie

  i've been reading "tcp/ip illustrated" and i started reading about ip forwarding. all about how you can receive a datagram and work out where to send it next based on the desination ip and your routing table. but what confused me is how (in a home network setting) the table itself is populated. is there a lower layer protocol at work here? does it come along with dhcp? or is it simply based on the ip address and netmask of each interface? i do know (from other books) that in the early days of ethernet one had to set up routing tables by hand, but i know i didn't do that.

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• use network drives as mount points during installation?

  - by ajsie

  is it possible to use network storage locations as mount points during installation? cause i want to separate system (ubuntu) with data (personal files). eg. if i have 5 computers i don't want to recreate /home/david 5 times. so i want to mount networkdrive/home to /home in local ubuntu server. so ALL users home folders could be used and maybe also networkdrive/projects to /projects. in that way its ok if i by accident repartitioned the local ubuntu server cause all data is not there on that server, but in the data server. is separating "data" from "logic" good in this case? and is it possible? what protocol should i use for the mapping over internet? (maybe the server is in Sweden, and the data is in Norway). thanks.

  Read the article

• Ubuntu getting wrong hostname from DHCP

  - by sam

  When provisioning new Ubuntu Precise (12.04) servers, the hostname they're getting seems to be generated from the DNS search path, not a reverse lookup on the hostname. Take the following configuration BIND is configured with the hostname, and reverse name Normal zone $TTL 600 $ORIGIN srv.local.net. @ IN SOA ns0.local.net. hostmaster.local.net. ( 2014082101 10800 3600 604800 600 ) @ IN NS ns0.local.net. @ IN MX 5 mail.local.net. my-new-server IN A 10.32.2.30 And reverse @ IN SOA ns0.local.net. hostmaster.local.net. ( 2014082101 10800 3600 604800 600 ) @ IN NS ns0.local.net. $ORIGIN 32.10.in-addr.arpa. 30.2 IN PTR my-new-server.srv.local.net. Then DHCPD is configured to hand out static leases based on mac addresses like so subnet 10.32.2.0 netmask 255.255.254.0 { option subnet-mask 255.255.254.0; option routers 10.32.2.1; option domain-name-servers 10.32.2.1; option domain-name "util.of1.local.net of1.local.net srv.local.net"; site-option-space "pxelinux"; option pxelinux.magic f1:00:74:7e; if exists dhcp-parameter-request-list { option dhcp-parameter-request-list = concat(option dhcp-parameter-request-list,d0,d1,d2,d3); } group { option pxelinux.configfile "pxelinux.cfg/pxeboot"; host my-new-server { fixed-address my-new-server.srv.local.net; hardware ethernet aa:aa:aa:bb:bb:bb; } } } So the hostname should be my-new-server.srv.local.net, however when building a Ubuntu 12.04 node, the hostname ends up as my-new-server.util.of1.local.net When building Lucid (10.04) hosts, the hostname will be correct, it's only on Precise/12.04 nodes we have the problem. Doing a normal and reverse lookup on the host and IP returns the correct result Sams-MacBook-Pro:~ sam$ host my-new-server my-new-server.srv.local.net has address 10.32.2.30 Sams-MacBook-Pro:~ sam$ host my-new-server.srv.local.net my-new-server.srv.local.net has address 10.32.2.30 Sams-MacBook-Pro:~ sam$ host 10.32.2.30 30.2.32.10.in-addr.arpa domain name pointer my-new-server.srv.local.net. The contents of the hosts file is incorrect too 127.0.0.1 localhost 127.0.1.1 my-new-server.util.of1.local.net of1.local.net srv.local.net my-new-server So it looks like when it creates the hosts file, it puts the entire contents of the DNS search path into the local address so the FQDN according to the server is the short hostname as defined, then the first domain in the search path. Is there a way to get around this behaviour, or fix this so it gets the hostname correctly? It's picking up the first part of the hostname, then the rest is wrong.

  Read the article

• netkit: why cant my router 4 pc4 ping my router 1 pc1 - how can I solve this please?

  - by donok

  Below I have four routers connected but my pc1 on r1 cannot ping my pc4 on r4 and also my pc2 on r2 cant ping my pc4 on r4 and vice versa. Below is a network diagram: and the configurations are below that, could anyone help me please on making them accessible? ![connecting 4 routers][1] I cant post my diagram on serverfault(less than 10 rep) so I did on stackoverflow and asked the same question. pc1: ifconfig eth0 195.11.14.5 netmask 255.255.255.0 broadcast 195.11.14.255 up route add default gw 195.11.14.1 dev eth0 pc2.start: ifconfig eth0 200.1.1.7 netmask 255.255.255.0 broadcast 200.1.1.255 up route add default gw 200.1.1.1 dev eth0 pc3: ifconfig eth0 195.20.14.9 netmask 255.255.255.0 broadcast 195.20.1.255 up route add default gw 195.20.14.1 dev eth0 pc4: ifconfig eth0 200.2.1.11 netmask 255.255.255.0 broadcast 200.2.1.255 up route add default gw 200.2.1.1 dev eth0 r1: ifconfig eth0 195.11.14.1 netmask 255.255.255.0 broadcast 195.11.14.255 up ifconfig eth1 100.0.0.9 netmask 255.255.255.252 broadcast 100.0.0.11 up route add -net 200.1.1.0 netmask 255.255.255.0 gw 100.0.0.10 dev eth1 route add default gw 100.0.0.10 lab.conf: if you need more on that Ill post it up but I think most of the info is there. Any help would be greatly appreciated especially trying to make a connection between pc4 and pc1, even if you think it does not make sense please explain why. Thank you.

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >