Search Results

Search found 56902 results on 2277 pages for 'stefan thieme@oracle com'.

Page 211/2277 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• Megacli is killing me, any help appreciated

  - by Stefan

  I run a server with 2 drives in raid0 configured through BIOS. I just added 2 more drives using hotplug (the server is dell r610 with RHEL 5.4 64bit) and I would like to configure a separate raid0 partition on these drives. I am getting the following error: /opt/MegaRAID/MegaCli/MegaCli64 -CfgLdAdd r0[32:2, 32:3] -a0 The specified physical disk does not have the appropriate attributes to complete the requested command. Exit Code: 0x26 All the parameters are correct and there is just no reason why this command could not work, see this (fujitsu is current raid, seagate is the new one I want to create): /opt/MegaRAID/MegaCli/MegaCli64 -PDList -aALL | egrep 'Adapter|Enclosure|Slot|Inquiry' Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA101174 Enclosure Device ID: 32 Slot Number: 1 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA10115T Enclosure Device ID: 32 Slot Number: 2 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS033SE0TF5K Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS023SE070FK I also tried to set up the drive as hotspare, also some strange error: /opt/MegaRAID/MegaCli/MegaCli64 -PDHSP -Set -physdrv[32:3] -a0 Adapter: 0: Set Physical Drive at EnclId-32 SlotId-3 as Hot Spare Failed. FW error description: The specified device is in a state that doesn't support the requested command. Exit Code: 0x32 As you can see the disk is in Unconfigured, Good state: Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Device Id: 3 Sequence Number: 1 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.875 GB [0x22dc0000 Sectors] Firmware state: Unconfigured(good), Spun Up SAS Address(0): 0x5000c50005cd20b1 SAS Address(1): 0x0 Connected Port Number: 3(path0) Inquiry Data: SEAGATE ST9300603SS FS023SE070FK FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: Foreign Foreign Secure: Drive is not secured by a foreign lock key Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :30C (86.00 F)

  Read the article

• /server-status shows over 240 requests like "OPTIONS * HTTP/1.0" 200 - "-" "Apache (internal dummy c

  - by Stefan Lasiewski

  Some details: Webserver: Apache/2.2.13 (FreeBSD) mod_ssl/2.2.13 OpenSSL/0.9.8e OS: FreeBSD 7.2-RELEASE This is a FreeBSD Jail. I believe I use the Apache 'prefork' MPM (I run the default for FreeBSD). I use the default values for MaxClients (256) I have enabled mod_status, with "ExtendedStatus On". When I view /server-status , I see a handful of regular requests. I also see over 240 requests from the 'localhost', like these. 37-0 - 0/0/1 . 0.00 1510 0 0.0 0.00 0.00 127.0.0.2 www.example.gov OPTIONS * HTTP/1.0 38-0 - 0/0/1 . 0.00 1509 0 0.0 0.00 0.00 127.0.0.2 www.example.gov OPTIONS * HTTP/1.0 39-0 - 0/0/3 . 0.00 1482 0 0.0 0.00 0.00 127.0.0.2 www.example.gov OPTIONS * HTTP/1.0 40-0 - 0/0/6 . 0.00 1445 0 0.0 0.00 0.00 127.0.0.2 www.example.gov OPTIONS * HTTP/1.0 I also see about 2417 requests yesterday from the localhost, like these: Apr 14 11:16:40 192.168.16.127 httpd[431]: www.example.gov 127.0.0.2 - - [15/Apr/2010:11:16:40 -0700] "OPTIONS * HTTP/1.0" 200 - "-" "Apache (internal dummy connection)" The page at http://wiki.apache.org/httpd/InternalDummyConnection says "These requests are perfectly normal and you do not, in general, need to worry about them", but I'm not so sure. Why are there over 230 of these? Are these active connections? If I have "MaxClients 256", and over 230 of these connections, it seems that my webserver is dangerously close to running out of available connections. It also seems like Apache should only need a handful of these "internal dummy connections" We actually had two unexplained outages last night, and I am wondering if these "internal dummy connection" caused us to run out of available connections. UPDATE 2010/04/16 It is 8 hours later. The /server-status page still shows that there are 243 lines which say "www.example.gov OPTION *". I believe these connections are not active. The server is mostly idle (1 requests currently being processed, 9 idle workers). There are only 18 active httpd processes on the Unix host. If these connections are not active, why do they show up under /server-status? I would have expected them to expire a few minutes after they were initialized.

  Read the article

• mysqlbinlog: unknown option '--ssl'

  - by Stefan Lasiewski

  I am running FreeBSD 7. running MySQL 5.1.36 from ports. I am trying to check some data in the MySQL binary log files, and I get the following error: # mysqlbinlog mysql-bin.000021 mysqlbinlog: unknown option '--ssl' In addition, I can't even view the help for this command: # mysqlbinlog --help mysqlbinlog: unknown option '--ssl' Why does mysqlbinlog not know about the option ssl? This server was compiled with SSL, and ssl is activated in the my.cnf configuration file. We use SSL for remote connections, but I am running this command on the local host.

  Read the article

• Automatically check for Security Updates on CentOS or Scientific Linux?

  - by Stefan Lasiewski

  We have machines running RedHat-based distros such as CentOS or Scientific Linux. We want the systems to automatically notify us if there are any known vulnerabilities to the installed packages. FreeBSD does this with the ports-mgmt/portaudit port. RedHat provides yum-plugin-security, which can check for vulnerabilities by their Bugzilla ID, CVE ID or advisory ID. In addition, Fedora recently started to support yum-plugin-security. I believe this was added in Fedora 16. Scientific Linux 6 did not support yum-plugin-security as of late 2011. It does ship with /etc/cron.daily/yum-autoupdate, which updates RPMs daily. I don't think this handles Security Updates only, however. CentOS does not support yum-plugin-security. I monitor the CentOS and Scientific Linux mailinglists for updates, but this is tedious and I want something which can be automated. For those of us who maintain CentOS and SL systems, are there any tools which can: Automatically (Progamatically, via cron) inform us if there are known vulnerabilities with my current RPMs. Optionally, automatically install the minimum upgrade required to address a security vulnerability, which would probably be yum update-minimal --security on the commandline? I have considered using yum-plugin-changelog to print out the changelog for each package, and then parse the output for certain strings. Are there any tools which do this already?

  Read the article

• What is the best free font converter?

  - by Stefan

  What is the best free font converter? Online or not doesn't mather. Please motivate your choice. One tip per post please.

  Read the article

• Bash vs. Gnu screen : Replace Ctrl-A with Ctrl-Shift-A

  - by Stefan Lasiewski

  I'm a new user to GNU Screen. I've been using Bash for a very long time, and I want to give GNU Screen a try. As you know, GNU Screen uses 'C-a' (Control-A) as as the command character. Trouble is, this interferes with the Line Editing feature in Bash (and GNU Readline), because Control-A in Bash will Move to the start of the line." I know I can set the Command Character to another key sequence, like "^Q" or "``" (Backtick), but I have trouble finding another key sequence which isn't already in use (^Q is used by the terminal, backtick is used when writing shell scripts). It appears that the Command Character may only be one or two characters in length. Can I set the GNU Screen control character to be something like "Control-Shift-A"? (I can't use more then one hyperlink yet, so I cannot link to the Bash documentation)

  Read the article

• Transfer VLAN tagged packets over WLAN?

  - by stefan.at.wpf

  I have the following composition of devices: [selfmade router] - ethernet - [WLAN router 1] ----- wlan ------ [WLAN router 2] WLAN router 2 has 5 ethernet ports, each as an own VLAN, so 5 VLANs. I want to manage the routing and firewalling between those VLANs at selfmade router. What technique would I use to pass the tagged vlan packets from WLAN router 2 to selfmade router? Could I use a bridge from WLAN router 2 to WLAN router 1 which itself has a bridge from WLAN router 1 to selfmade router or do I have a wrong understanding of a bridge? Thanks for any hint on this :-)

  Read the article

• Difference between "Redirect permanent" vs. mod_rewrite

  - by Stefan Lasiewski

  This is an Apache httpd 2.2 server. We require that access to this webserver be encrypted by HTTPS. When web clients visit my site at http://www.example.org/$foo (port 80), I want to redirect their request to the HTTPS encrypted website at https://www.example.org/$foo . There seem to be two common ways to do this: First method uses the 'Redirect' directive from mod_alias: <VirtualHost *:80> Redirect permanent / https://www.example.org/ </VirtualHost> Second method uses mod_rewrite: <VirtualHost *:80> RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (.*) https://%{HTTP_HOST}%{REQUEST_URI} </VirtualHost> What is the difference between a "Redirect permanent" and the mod_rewrite stanza. Is one better then the other?

  Read the article

• With the Supermicro Embeded BMC, is it possible to connect to Serial Over Lan via SSH?

  - by Stefan Lasiewski

  I have several dozen Supermicro servers which use the Supermicro Embedded BMC. The documentation on that page suggests that I can access the Serial Over LAN (Serial Console) over SSH: SMASH and CLP support SSH based SOL Power control of the server But when I ssh into my BMC, all I see is a Busybox implementation, with no clear ability to connect to the SOL: # ssh 192.168.100.100 -l ADMIN [email protected]'s password: BusyBox v1.1.3 (2011.02.12-01:48+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. # show -sh: show: not found # smash -sh: smash: not found Supermicro support is giving me inconsistent answers. Is it possible to connect to the SOL via the SSH interface?

  Read the article

• Why does `rpm` show 3 httpd packages, and which one provides the real httpd?

  - by Stefan Lasiewski

  I ran yum update on my CentOS5 webserver a few days ago. Today I just noticed that I have 3 httpd-* rpms! How can I end up with three RPMs for httpd (My other servers only have one httpd rpm). I want to make sure that my server has a patched, updated version of /usr/sbin/httpd. How can I tell which one of these packages provides the httpd binary at /usr/sbin/httpd? [root@node1 ~]# rpm -q httpd httpd-2.2.3-76.el5.centos httpd-2.2.3-78.el5.centos httpd-2.2.3-83.el5.centos [root@node1 ~]# /usr/sbin/httpd -V |grep version Server version: Apache/2.2.3 [root@node1 ~]# rpm -q httpd-2.2.3-76.el5.centos --list |grep -w /usr/sbin/httpd /usr/sbin/httpd /usr/sbin/httpd.event /usr/sbin/httpd.worker [root@node1 ~]# rpm -q httpd-2.2.3-78.el5.centos --list |grep -w /usr/sbin/httpd /usr/sbin/httpd /usr/sbin/httpd.event /usr/sbin/httpd.worker [root@node1 ~]# rpm -q httpd-2.2.3-83.el5.centos --list |grep -w /usr/sbin/httpd /usr/sbin/httpd /usr/sbin/httpd.event /usr/sbin/httpd.worker [root@node1 ~]# root@node1 ~]# rpm -q --provides httpd |grep -w httpd config(httpd) = 2.2.3-76.el5.centos httpd-mmn = 20051115 httpd = 2.2.3-76.el5.centos config(httpd) = 2.2.3-78.el5.centos httpd-mmn = 20051115 httpd = 2.2.3-78.el5.centos config(httpd) = 2.2.3-83.el5.centos httpd-mmn = 20051115 httpd = 2.2.3-83.el5.centos Update: Answering Mark Wagner's questions: [root@node1 ~]# rpm -q -f /usr/sbin/httpd httpd-2.2.3-76.el5.centos httpd-2.2.3-78.el5.centos httpd-2.2.3-83.el5.centos [root@node1 ~]# rpm -V httpd-2.2.3-83.el5.centos S.5..... c /etc/logrotate.d/httpd S.5..... c /etc/rc.d/init.d/httpd ....L... /var/www

  Read the article

• Does a 3ware "ECC-ERROR" matter on a JBOD when I have ZFS?

  - by Stefan Lasiewski

  I have a FreeBSD 8.x machine running ZFS and with a 3ware 9690SA controller. The 3ware controller shows an ECC-ERROR with one of the disks: //host> /c0 show VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 279.39 GB SAS 0 - SEAGATE ST3300657SS p1 OK u0 279.39 GB SAS 1 - SEAGATE ST3300657SS p2 OK u1 931.51 GB SAS 2 - SEAGATE ST31000640SS p3 ECC-ERROR u2 931.51 GB SAS 3 - SEAGATE ST31000640SS p4 OK u3 931.51 GB SAS 4 - SEAGATE ST31000640SS /c0 show events shows no ECC errors in it's recent history. ZFS does not currently detect any errors. zpool status says No known data errors My question: Is this ECC-ERROR something that I need to be concerned about? According to the 3ware CLI 9.5.2 Manual, an ECC-ERROR means that the 3ware controller caught a read-error for one or more sectors on this drive. This sometimes occurs when a RAID array is recovering from a failed disk. I believe that ECC-ERRORS can also be detected when the 3ware Controller verifies each disk. None of the drives have failed and thus there was no drive rebuild, so I assume that 3ware discovered a bad sector when it ran it's weekly auto-verify scan of the disks. Is this a safe assumption? According to our logs, ZFS has not detected any bad sectors on this drive. ZFS can work around read errors -- if ZFS detects a bad sector on the drive, it will simply mark that sector as bad and never use it again. From the ZFS perspective one bad sector isn't a big deal, although it might indicate that the drive is starting to go bad.

  Read the article

• Centralized sudo sudoers file?

  - by Stefan Thyberg

  I am the admin of several different servers and currently there is a different sudoers file on each one. This is getting slightly out of hand as quite often I need to give someone permissions to do something with sudo but it only gets done on one server. Is there an easy way of editing the sudoers file just on my central server and then distributing it by SFTP or something like that to the other servers in an easy way? Mostly wondering how other sysadmins solve this problem, since the sudoers file doesn't seem to be remotely accessible with NIS, for example. Operating system is SUSE Linux Enterprise Server 11 64-bit, but it shouldn't matter. EDIT: Every machine will, for now, have the same sudoers file. EDIT2: The accepted answer's comment was the closest to what I actually went ahead and did. I am right now using an SVN-supported puppet-installation and after a few headaches, it's working very well.

  Read the article

• kickstart ks.cfg: Where should 'url' point?

  - by Stefan Lasiewski

  I have a kickstart file (ks.cfg) on a floppy (Old style). I am trying to install CentOS 5.4. The top of my ks.cfg says this: install # Install from local cdrom or over the network. #cdrom url --url http://kickstart.example.org/pub/centos/5.4/ On the Apache server side, this command is failing with these 404s: kickstart.example.org 192.168.16.180 - - [01/Jun/2010:17:24:30 -0700] "GET /pub/centos/5.4///disc1/.discinfo HTTP/1.1" 404 314 "-" "urlgrabber/3.1.0" kickstart.example.org 192.168.16.180 - - [01/Jun/2010:17:24:43 -0700] "GET /pub/centos/5.4/repodata/repomd.xml HTTP/1.1" 404 316 "-" "urlgrabber/3.1.0 yum/3.2.22" It seems that the value of my url doesn't match the directory structure on the server. I swear this worked a few months ago. Someone else maintains the Yum repository, and they say nothing has changed. What should the value of url URL be? Should this only include the OS (/pub/centos/5.4/), or should it include the architecture (/pub/centos/5.4/os/x86_64 )? I see that Kickstart is trying to grab a file called 'repomd.xml', but why is it looking in '/pub/centos/5.4/repodata/repomd.xml', when these files actually exist at '/pub/centos/5.4/os/x86_64/repodata/repomd.xml' and other locations at '/pub/centos/5.4/*/$ARCH/repodata/repomd.xml'? I don't see this documented or explained well in the [RedHat 5 Installation Guide1]

  Read the article

• Windows 7 USB power lose after a few seconds / minutes

  - by Stefan Dunn

  My friend's computer has a problem where the USB ports causes problems with the power of some devices connected to the computer. The USB mouse has no problems, however the Wireless Adapter looses power after around 20 seconds of use and USB Flash Drives cause the computer to either freeze, lose power (and become unresponsive) or become disconnected (still shown in Device Manager, but not in My Computer) when trying to transfer any type of file to / from the computer. I have a suspicion it's the Motherboard but could it also be a Software problem? Tried a new case, RAM, CPU and GFX Card which had no effect. The problem occurs on both the Front USB and Back (Motherboard) USB Ports. UPDATE: Tried the USB devices with an Ubuntu Live CD and they work fine, could this mean it's a problem with Windows (x64)?

  Read the article

• FreeBSD Ports: How can I see all dependencies, and all dependencies for those dependencies, for a port?

  - by Stefan Lasiewski

  I'm trying to build a port which depends on apache-ant. I thought I could run make build-depends-list to see all dependencies required by this port: # make build-depends-list /usr/ports/devel/apache-ant /usr/ports/java/jdk16 /usr/ports/math/gmp But after installing everything, the port had a dependency list which was a mile long: apache-ant-1.8.1 desktop-file-utils-0.15_2 gamin-0.1.10_4 gettext-0.18.1.1 gio-fam-backend-2.26.1 glib-2.26.1_1 gmp-5.0.1 inputproto-2.0 javavmwrapper-2.3.5 kbproto-1.0.4 libX11-1.3.3_1,1 libXau-1.0.5 libXdmcp-1.0.3 libXext-1.1.1,1 libXi-1.3,1 libXtst-1.1.0 libiconv-1.13.1_1 libpthread-stubs-0.3_3 libxcb-1.7 pcre-8.12 perl-5.10.1_3 pkg-config-0.25_1 python26-2.6.6 recordproto-1.14 unzip-6.0 xextproto-7.1.1 xproto How can I see all dependencies, and all subdependencies for a port?

  Read the article

• How can I tell if I have PCI Express 2.0 or 2.1?

  - by Stefan Lasiewski

  I am looking at a variety of PCI Express cards, such as a SATA RAID Controller and a Video Card. Some of these cards say they only support PCI Express 2.1, not PCI Express 2.0. I know that my motherboard supports PCI Express 2-something, but the manual doesn't say '2.0' or '2.1'. How can I tell if the PCIe slot on my motherboard is PCI Express 2.0 or PCI Express 2.1? Is it possible to determine the PCIe type from the Windows or Linux commandline? I was under the impression that most PCI Express 2.1 devices are backwards compatible with PCI Express 2.0. Is it possible that the vendor is wrong in saying that PCI Express 2.1 is required?

  Read the article

• Automatically reconnect to ODBC sources?

  - by stefan.at.wpf

  I am using Asterisk 1.8.10.1 and a MySQL database connected via ODBC to store CDRs. When my MySQL database isn't available when Asterisk starts or has an outage while Asterisk is running, I would expect Asterisk to retry to connect to the database, but this doesn't happen! Anyone knows where I can enable some kidn of automatic reconnect to databases in Asterisk? My res_odbc.conf looks like this: [asterisk] enabled => yes dsn => asterisk-connector username => user password => pass pre-connect => yes pooling => no limit => 1 idlecheck => 1 negative_connection_cache => 1

  Read the article

• Unable to make my bios see my sata hdd

  - by Stefan

  I know there are many question about that, but I tried everything and I'm still not able to make my bios see my sata2 hdd. I've got a QDI motherbord with no sata port; only 2 ide ports. I had an old ide hdd, now i've removed it and bought a sata2 hdd. Since my pc has no sata slots i bouth a ide-to-sata adapter. So, i don't have any os installed on the new drive, and the old drive is removed. My problem is that I'm unable to see my hdd on bios. I suppose that my bios, since it's an old version, doesn't have sata drivers, but I don't know if I must install it and also I dont know how to do it. Anyone can help me?

  Read the article

• Where is the central ZFS website now?

  - by Stefan Lasiewski

  Oracle dumped OpenSolaris in Fall 2010, and it is unclear if Oracle will continue to publicly release updates to ZFS, except maybe after they release their next major version of Solaris. FreeBSD now has ZFS v28 available for testing. But where did v28 come from? I notice that the main ZFS website does not show version 28 available. Has this website been abandoned? If so, where is the central website for the ZFS project, so that I can browse the repo, read the mailing lists, read the release notes, etc. (I realize that OpenSolaris has been dumped by Oracle, and that they are limiting their ZFS releases to the community).

  Read the article

• Can ping device from one computer and not the other

  - by Sean Duggan

  I've recently been assigned to work on a diagnostic program done in C++ which communicates with a piece of electronic equipment. Our normal scenario involves communicating via an RS232 interface, but I've been asked to make our program work over ethernet, source code having been done in Visual Basic. After much thrashing about trying to get the code to work and continuing to get 10049 Winsock errors when I tried to connect, I tried pinging the switch. From the computer the VB program is running on, I can see the switch via ping, nslookup, tracert, and pathping (I was going down the list of programs) and I can do this via URI or IP address. From my laptop, sending the same commands fails every time. They're both using the same network cable and the same USB-to-Ethernet device (I've been swapping them between tests) but one can see the switch and the other cannot. I'm working on the programming end, but the ping results makes me think that there might be a network issue stymieing me. wry grin I'm not much of a network guy, so I'm appealing to expert assistance. Both computers are running Windows XP if that helps. The connection is to an "IP-RS8" device which then connects to our VCU-C units. Each unit is accessible via URI or IP address on the desktop computer we usually have connected to the units (it's running the older VB program that I was asked to lift the networking code from). The connection is made via a USB-to-Ethernet adapter so as to leave the regular Ethernet port available for connecting to the company network. Hmm... come to think of it, I've probably been confusing the issue, talking about pinging "the switch" rather than indicating that it's the devices. My apologies. Communication is generally done with a DLL that uses Winsock functions to make queries for data from the VCU and then to receive. I'm failing when connecting. I haven't found anything on the firewall which should block these commands, but I'll keep poking. I don't know if it's potentially relevant, but on the desktop, the adapter maps to Local Area Connection 3 while on the laptop, it consistently maps to Local Area Connection 2. Currently reading up on DHCP. IPConfig /all results: Desktop Host Name . . . . . . . . . . . . : AMERDAEXXXXXX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Broadcom NetXtreme XYxx Gigabit Controller Physical Address. . . . . . . . . : YY-XX-YB-XX-XX-XX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XXX Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XY:XX:XX AM Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX axYYYYX USBX.Y to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XY.Y.Y.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XY.Y.Y.X DHCP Server . . . . . . . . . . . : XY.Y.Y.XY DNS Servers . . . . . . . . . . . : XY.Y.Y.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XY AM Lease Expires . . . . . . . . . . : Tuesday, August YX, XYXX XX:XY:XY AM Laptop Windows IP Configuration Host Name . . . . . . . . . . . . : AMERLAFYYXXYX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Intel(R) 82567LM Gigabit Network Connection Physical Address. . . . . . . . . : YY-XY-BY-DY-XB-YX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XY Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XX:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XX:XX:XX AM Ethernet adapter {XYXAAYXX-YEDY-XXYX-YYEX-BYXYXXYEEYEX}: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Nortel IPSECSHM Adapter - Packet Scheduler iniport Physical Address. . . . . . . . . : XX-XX-XX-XX-XX-YY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : Y.Y.Y.Y Subnet Mask . . . . . . . . . . . : Y.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Leaf Networks Adapter: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Leaf Networks Adapter Physical Address. . . . . . . . . : YY-FF-FA-BC-YF-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : X.XYY.XY.XX Subnet Mask . . . . . . . . . . . : XXX.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : YY-FX-AX-YA-BY-CA Ethernet adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Intel(R) WiFi Link 5300 AGN Physical Address. . . . . . . . . : YY-XX-YA-CX-FC-YE Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX ax88772 USB2.0 to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : XYX.XYY.X.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXX.Y Default Gateway . . . . . . . . . :

  Read the article

• How do I force a server to leave a SharePoint farm

  - by Stefan

  I have two web servers in a SharePoint (WSS 3.0) farm with one database server for the config and content databases. I already moved my content databases to a new database server successfully. But when I tried to move the sharepoint config database using the "stsadm deleteconfigdb" and "stsadm setconfigdb" commands, one of my servers got stuck in an intermediate state. I was able to join one of the web servers with the config database on the new server, but the other server is not able to join because it believes it is already part of the farm (which it used to be, before the move). On the central administration it says the status of the services on the server is "stopping". Even after rebooting all servers involved, uninstalling SharePoint and what not, this status does not change, and because of it, I am not able to join the second server with the new config database. I get random error messages when trying to join the farm. I believe that if I can unstuck this server, it will be able to join the farm again. The farm believes the second server is already part of it, but the web server itself knows its not. Any ideas on how to forcefully kick out a server from the farm?

  Read the article

• Windows 8 Internet Explorer proxy automation script

  - by Stefan Bollmann

  Similar to this post, I'd like to change my proxy settings using a script. However, it fails. When I am behind the proxy, IE does not connect to the internet. Here I try the first solution from craig: function FindProxyForURL(url, host) { if (isInNet(myIpAddress(), "myactualip", "myactualsubnetip")) return "PROXY proxyasshowninpicture:portihavetouseforthisproxy_see_picture"; else return "DIRECT"; } Also this test, where isInNet should surely return true does not help: function FindProxyForURL(url, host) { if (isInNet("myactualip", "myactualip", "myactualsubnetip")) return "PROXY proxyasshowninpicture:portihavetouseforthisproxy_see_picture"; else return "DIRECT"; } **This script is saved as proxy.pac in c:\windows and my configuration is* in LAN settings: No automatically detected settings, yes, use automatic config script: file://c:/windows/proxy.pac No proxy server. *(i am not allowed to post screenshots..) So, what am I doing wrong? ---------------- update -------------- However, when I set up a proxy in my LAN configurations: IE -> Internet Options -> Connections -> LAN Settings check: Use a proxy Server for your LAN Address: <a pingable proxy> Port: <portnr> everything is fine for this environment. Now I try a simpler script like function FindProxyForURL(url, host) { return "PROXY <pingable proxy>:<portnr>; DIRECT"; } With a configuration described above** I am not able to get through the proxy.

  Read the article

• CentOS 5.6: How to resolve php53 RPM dependency conflict with php-mcrypt and php-common?

  - by Stefan Lasiewski

  We are running a CentOS 5.6 system, and want to install php53 with php-mcrypt. However, this introduces a dependency conflict between php-common & php53-common. Does anyone have a good workaround for this problem? host # yum install php-mcrypt Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * epel: linux.mirrors.es.net Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php-mcrypt.x86_64 0:5.1.6-15.el5.centos.1 set to be updated --> Processing Dependency: php-api = 20041225 for package: php-mcrypt --> Processing Dependency: php >= 5.1.6 for package: php-mcrypt --> Running transaction check ---> Package php.x86_64 0:5.1.6-27.el5_5.3 set to be updated --> Processing Dependency: php-cli = 5.1.6-27.el5_5.3 for package: php ---> Package php-common.x86_64 0:5.1.6-27.el5_5.3 set to be updated --> Running transaction check ---> Package php-cli.x86_64 0:5.1.6-27.el5_5.3 set to be updated --> Processing Conflict: php53-common conflicts php-common --> Finished Dependency Resolution php53-common-5.3.3-1.el5_6.1.x86_64 from installed has depsolving problems --> php53-common conflicts with php-common Error: php53-common conflicts with php-common You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest This is apparently a known problem (See php-devel, Bug 700179 and Bug 695708) and this post at the CentOS forums, but there is no official fix yet.

  Read the article

• SSH not working over IPSec tunnel (Strongswan)

  - by PattPatel

  I configured a small network on a cloud virtual machine. This virtual machine has a static IP address assigned to eth0 interface that I'll call $EXTIP. mydomain.com points to $EXTIP. Inside, I have some linux containers, that get their ip through DHCP in the Subnet 10.0.0.0/24 (i called the virtual interface nat ). They run some services that can be reached through DNAT. Then I wanted to connect to these containers through an IPSec tunnel, so I configured StrongSwan. ipsec.conf: conn %default dpdaction=none rekey=no conn remote keyexchange=ikev2 ike=######## left=[$EXTIP] leftsubnet=10.0.1.0/24,10.0.0.0/24 leftauth=pubkey lefthostaccess=yes leftcert=########.pem leftfirewall=yes leftid="#########" right=%any rightsourceip=10.0.1.0/24 rightauth=######## rightid=%any rightsendcert=never eap_identity=%any auto=add type=tunnel Everything works fine, IPSec clients get IPs of the 10.0.1.0/24 subnet and can reach the containers subnet. My problem is that I'm not able to get SSH connections over the tunnel. It simply does not work, ssh client does not produce any output. Sniffing with tcpdump gives: tcpdump: 09:50:29.648206 ARP, Request who-has 10.0.0.1 tell mydomain.com, length 28 09:50:29.648246 ARP, Reply 10.0.0.1 is-at 00:ff:aa:00:00:01 (oui Unknown), length 28 09:50:29.648253 IP mydomain.com.54869 > 10.0.0.1.ssh: Flags [S], seq 4007849772, win 29200, options [mss 1460,sackOK,TS val 1151153 ecr 0,nop,wscale 7], length 0 09:50:29.648296 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [S.], seq 2809522632, ack 4007849773, win 14480, options [mss 1460,sackOK,TS val 11482992 ecr 1151153,nop,wscale 6], length 0 09:50:29.677225 IP mydomain.com.54869 > 10.0.0.1.ssh: Flags [.], ack 2809522633, win 229, options [nop,nop,TS val 1151162 ecr 11482992], length 0 09:50:29.679370 IP mydomain.com.54869 > 10.0.0.1.ssh: Flags [P.], seq 0:23, ack 1, win 229, options [nop,nop,TS val 1151162 ecr 11482992], length 23 09:50:29.679403 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [.], ack 24, win 227, options [nop,nop,TS val 11483002 ecr 1151162], length 0 09:50:29.684337 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [P.], seq 1:32, ack 24, win 227, options [nop,nop,TS val 11483003 ecr 1151162], length 31 09:50:29.685471 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [.], seq 32:1480, ack 24, win 227, options [nop,nop,TS val 11483003 ecr 1151162], length 1448 09:50:29.685519 IP mydomain.com > 10.0.0.1: ICMP mydomain.com unreachable - need to frag (mtu 1422), length 556 09:50:29.685567 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [.], seq 32:1402, ack 24, win 227, options [nop,nop,TS val 11483003 ecr 1151162], length 1370 09:50:29.685572 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [.], seq 1402:1480, ack 24, win 227, options [nop,nop,TS val 11483003 ecr 1151162], length 78 09:50:29.714601 IP mydomain.com.54869 > 10.0.0.1.ssh: Flags [.], ack 32, win 229, options [nop,nop,TS val 1151173 ecr 11483003], length 0 09:50:29.714642 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [P.], seq 1480:1600, ack 24, win 227, options [nop,nop,TS val 11483012 ecr 1151173], length 120 09:50:29.723649 IP mydomain.com.54869 > 10.0.0.1.ssh: Flags [P.], seq 1393:1959, ack 32, win 229, options [nop,nop,TS val 1151174 ecr 11483003], length 566 09:50:29.723677 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [.], ack 24, win 227, options [nop,nop,TS val 11483015 ecr 1151173,nop,nop,sack 1 {1394:1960}], length 0 09:50:29.725688 IP mydomain.com.54869 > 10.0.0.1.ssh: Flags [.], ack 1480, win 251, options [nop,nop,TS val 1151177 ecr 11483003], length 0 09:50:29.952394 IP 10.0.0.1.ssh > 10.0.1.2.54869: Flags [P.], seq 1480:1600, ack 24, win 227, options [nop,nop,TS val 11483084 ecr 1151173,nop,nop,sack 1 {1394:1960}], length 120 09:50:29.981056 IP mydomain.com.54869 > 10.0.0.1.ssh: Flags [.], ack 1600, win 251, options [nop,nop,TS val 1151253 ecr 11483084,nop,nop,sack 1 {1480:1600}], length 0 If you need it this is my iptables configuration file: iptables: *filter :INPUT ACCEPT [144:9669] :FORWARD DROP [0:0] :OUTPUT ACCEPT [97:15649] :interfacce-trusted - [0:0] :porte-trusted - [0:0] -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A FORWARD -j interfacce-trusted -A FORWARD -j porte-trusted -A FORWARD -j REJECT --reject-with icmp-host-unreachable -A FORWARD -d 10.0.0.1/32 -p tcp -m tcp --dport 80 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 10.0.0.1/32 -p tcp -m tcp --dport 443 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 10.0.0.3/32 -p tcp -m tcp --dport 1234 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A interfacce-trusted -i nat -j ACCEPT -A porte-trusted -d 10.0.0.1/32 -p tcp -m tcp --dport 80 -j ACCEPT -A porte-trusted -d 10.0.0.1/32 -p tcp -m tcp --dport 443 -j ACCEPT -A porte-trusted -d 10.0.0.3/32 -p tcp -m tcp --dport 1234 -j ACCEPT COMMIT *nat :PREROUTING ACCEPT [10:600] :INPUT ACCEPT [10:600] :OUTPUT ACCEPT [4:268] :POSTROUTING ACCEPT [18:1108] -A PREROUTING -d [$EXTIP] -p tcp -m tcp --dport 80 -j DNAT --to-destination 10.0.0.1:80 -A PREROUTING -d [$EXTIP] -p tcp -m tcp --dport 443 -j DNAT --to-destination 10.0.0.1:443 -A PREROUTING -d [$EXTIP] -p tcp -m tcp --dport 8069 -j DNAT --to-destination 10.0.0.3:1234 -A POSTROUTING -s 10.0.0.0/24 -o eth0 -m policy --dir out --pol ipsec -j ACCEPT -A POSTROUTING -s 10.0.1.0/24 -o nat -j MASQUERADE -A POSTROUTING -s 10.0.0.0/24 -o eth0 -j MASQUERADE COMMIT Probably I'm missing something stupid... Thanks in advance for helping :))

  Read the article

• Admin mode on Procurve Switches

  - by stefan.at.wpf

  Not being a network expert, I spent some time configuring my network, until I found my mistake: On my HP ProCurve Switch 1810G, I thought that "Admin mode" means whether the administrative interface can be accessed from this port. Well, it means whether the port is enabled or not. Extract from the help function: Admin Mode - Select to enable the port-control administration state. Click to enable and have the port participate in the network.(Default : Enabled ) Well, of course I didn't read the help, because I didn't doubt it's for the adminsitrative interface and suspected an error somewhere else. Anyway, I am wondering if that is a commonly used term for enabling/disabling ports or if HP just wanted to make my life harder? I can't understand why this option isn't just called "Enable port"!? Here's a screenshot of how it looks in the web interface (yeah, shame on me for using a web interface)

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >