Search Results

Search found 8001 results on 321 pages for 'empty'.

Page 215/321 | < Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >

• Ubuntu 13.10 - How to disable LVM and cryptsetup? cryptsetup: evms_activate is not available

  - by NeverEndingQueue

  I am trying to remove whole drive encryption from my Ubuntu installation. I've run Ubuntu from Live CD, mounted crypt partition and copied it to another partition /dev/sda3. sudo cryptsetup luksOpen /dev/sda5 crypt1 sudo dd if=/dev/ubuntu-vg/root of=/dev/sda3 bs=1M After that I've run boot-repair: https://help.ubuntu.com/community/Boot-Repair Added entry to /etc/fstab: UUID=<uuid> / ext4 errors=remount-ro 0 1 Of course I've replaced with blkid result of my /dev/sda3. I've also deleted overlayfs and tmpfs lines from /etc/fstab. (I've just compared it to content of /etc/fstab in non-encrypted Ubuntu installation and could not find overlayfs and tmpfs). I've chrooted from LiveCD into my system and rebuilt initramfs: http://blog.leenix.co.uk/2012/07/evmsactivate-is-not-available-on-boot.html I've also removed cryptsetup using apt-get remove. Basically I can easily mount my system partition from Live CD (without setting up the encryption and LVM stuff), but can not boot from it. Instead I see: cryptsetup: evms_activate is not available When I've chosen the Recovery mode I've seen this: Begin: Mounting root file system ... Begin: Running /script/local-top ... Reading all physical volumes. This may take a while ... No volume groups found cryptsetup: evms_activate is not available Begin: Waiting for encrytpted source device ... My /etc/crypttab is empty. I am pretty sure that system tries to find encrypted partition, search for LVMs etc. Do you have ideas what could be the problem or how can I fix it? Thanks

  Read the article

• Upgrading memory in a laptop

  - by ulidtko

  I'm a bit confused about all the memory types and various bus frequencies of modern consumer PCs. Requesting expert help on the subject. So far I'm confident that: I have an Asus X51L laptop with an unknown set of configuration options. The CPU in there supports PAE, so I still have a chance to extend the memory beyond 3GiB; and the upper limit of the system is 8GiB. (?) The laptop has two SODIMM slots, one of which is occupied by a 2GiB bank, and the other one is empty. dmidecode and lshw tools consistently state 533 Mhz frequency of the bank. The last one confuses me the most. I failed to find out characteristics of the northbridge in this laptop, and still can't figure out what DDR2 to seek for. Is it DDR2-1066? Or, rather, PC2-8500/PC2-8600? Wouldn't a DDR2-800 bank harm the system's performance? Which kind of modules should I look up in stores? Update: I have bought a 2 GiB DDR2-800 SODIMM, and it seams that the system can't handle 4 GiB of memory. When installed by itself in either slot, both new and old bank (which btw happens to be marked GDDR2-677) work just perfectly; i.e. any configuration resulting in 2 GiB works. When both banks are installed though (totalling in 4 GiB), the memcheck86 tool produces horrible artifacts and crashes, and system reboots; an Ubuntu system can be started and even logged into a Unity session, but the system reboots too in this case from even a minor RAM load. So it's pretty obvious to me now that this laptop doesn't support 4 GiB of RAM or more.

  Read the article

• Migrating from one linux install to another: How to keep the second disk around?

  - by Jim Miller

  I've got a linux box running Fedora 19 that I want to move to CentOS 6.4. Rather than trying to do something fancy with the current disk (which has also accumulated a lot of sludge over the years), I'm going to get a new disk, put CentOS on that, and then move the to-be-preserved bits of stuff from the old disk to the new one. I haven't done this yet, but I presume it should be semi-straightforward -- do the CentOS install on the new disk, mount the old disk on /olddisk or somesuch, and start copying. However, I'm not sure how to handle getting the machine to recognize the new empty disk as the target of the CentOS install (I suppose I can just pull the old disk during the installation), remember that this is the intended boot disk once the install has happened), and tweak /etc/fstab (right?) to set up the old disk on the desired mount point. (Both disks are, or will be, SATA.) I could probably hack it together without losing too much hair or doing too much damage, but could anyone offer some advice that would get/keep me on the right track? Thanks!

  Read the article

• Why does BitLocker need a minimum volume size of 64 MB?

  - by Iszi

  Since the future of TrueCrypt appears to be still unclear, I figured I'd try to get my stuff migrated into BitLocker at least for the time being. I nearly never have to access my encrypted data from anything that's not BitLocker-capable, so cross-platform compatibility isn't a big deal to me at this time. However, I am having a bit of an issue understanding the minimum requirement of a 64 MB volume. With TrueCrypt, I was able to protect small files (and most of my protected files are fairly small) in containers down to 300 KB or even less. When I finally created a VHD of an appropriate size last night (100 MB), it seemed the file system itself only took up about 3 MB and encrypting it with BitLocker didn't appear to take up any more. While 3 MB is still an order of magnitude larger than the smallest volume I could make with TrueCrypt, it's still relatively reasonable in comparison to 64 MB. This is an especially large amount of overhead (and largely wasted at that, since it's mostly empty space for now) when I consider that some of these volumes will be stored and synced in the cloud. What possible reasons could BitLocker have for needing volumes to be 64 MB large, when it's not even appearing to use that space? BitLocker FAQ on TechNet

  Read the article

• nginx logrotate config

  - by TomOP

  Whats the best way to rotate nginx logfiles? In my opinion, I should create a file "nginx" in /etc/logrotate.d/ and fill it with the following code and do a /etc/init.d/syslog restart after that. This would be my config (I havn't tested it yet): /usr/local/nginx/logs/*.log { #rotate the logfile(s) daily daily # adds extension like YYYYMMDD instead of simply adding a number dateext # If log file is missing, go on to next one without issuing an error msg missingok # Save logfiles for the last 49 days rotate 49 # Old versions of log files are compressed with gzip compress # Postpone compression of the previous log file to the next rotation cycle delaycompress # Do not rotate the log if it is empty notifempty # create mode owner group create 644 nginx nginx #after logfile is rotated and nginx.pid exists, send the USR1 signal postrotate [ ! -f /usr/local/nginx/logs/nginx.pid ] || kill -USR1 `cat /usr/local/nginx/logs/nginx.pid` endscript } I have both the access.log and error.log files in /usr/local/nginx/logs/ and want to rotate both daily. Can anyone please tell me if "dateext" is correct? I want the log filename to be something like "access.log-2010-12-04". One more thing: Can I do the log rotation every day on a specific time (e.g. 11 pm)? If so, how? Thanks.

  Read the article

• Combine multiple rows into one

  - by Jim

  I am trying to combine multiple rows of data into one. Column A contains the value on which the groupings will be based -- rows whose Column A values match will be combined into one row. My range extends from column A through X so I need a matching row of data to start in column Y. Example: +--------------+ ¦ 1001 ¦ A ¦ C ¦ ¦ 1001 ¦ B ¦ D ¦ ¦ 1002 ¦ A ¦ E ¦ ¦ 1002 ¦ B ¦ F ¦ ¦ 1002 ¦ C ¦ G ¦ +--------------+ Desired Result: +------------------------------+ ¦ 1001 ¦ A ¦ C ¦ B ¦ D ¦ ¦ ¦ ¦ 1002 ¦ A ¦ E ¦ B ¦ F ¦ C ¦ G ¦ +------------------------------+ The VBA code I am currently using is not taking the entire contents of the matched row. It is only taking the data in the 2nd column and moving it up. VBA Code: Sub Mergeitems() Dim cl As Range Dim rw As Range Set rw = ActiveCell Do While rw <> "" ' for each row in data set ' find first empty cell on row Set cl = rw.Offset(0, 1) Do While cl <> "" Set cl = cl.Offset(0, 1) Loop ' if next row needs to be processed... Do While rw = rw.Offset(1, 0) cl = rw.Offset(1, 1) ' move the data Set cl = cl.Offset(0, 1) ' update pointer to next blank cell rw.Offset(1, 0).EntireRow.Delete xlShiftUp ' delete old data Loop ' next row Set rw = rw.Offset(1, 0) Loop End Sub

  Read the article

• My Mac OS X 10.5 netstat reveals a lot of open UDP connections.

  - by bboyreason

  here are my netstat results (besides server-less connections): Active Internet connections Proto Recv-Q Send-Q Local Address Foreign Address (state) tcp4 0 0 192.168.1.98.49224 r1.ycpi.vip.sp2..http ESTABLISHED tcp4 0 0 192.168.1.98.49223 r1.ycpi.vip.sp2..http ESTABLISHED tcp4 0 0 192.168.1.98.49203 lax04s01-in-f189.https ESTABLISHED tcp4 0 0 192.168.1.98.49201 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49198 lax04s01-in-f19..http ESTABLISHED tcp4 0 0 192.168.1.98.49196 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49194 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49192 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49183 r1.ycpi.vip.sp2..http ESTABLISHED tcp4 0 37 192.168.1.98.49179 l1.login.vip.sp1.https CLOSING tcp4 0 0 192.168.1.98.49175 lax04s01-in-f104.https ESTABLISHED tcp4 0 37 192.168.1.98.49167 l1.login.vip.sp1.https LAST_ACK tcp4 0 0 192.168.1.98.49164 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49174 69.31.112.122.http TIME_WAIT tcp4 0 0 192.168.1.98.49173 69.31.113.83.http TIME_WAIT udp4 0 0 *.ipp **.* udp4 0 0 192.168.1.98.ntp **.* udp4 0 0 *.49628 **.* udp4 0 0 *.51997 **.* udp4 0 0 *.64675 **.* udp4 0 0 *.61947 **.* udp4 0 0 *.65152 **.* udp4 0 0 *.55643 **.* udp4 0 0 *.51704 **.* udp4 0 0 *.59757 **.* udp4 0 0 *.53643 **.* udp4 0 0 *.65346 **.* udp4 0 0 *.61960 **.* udp4 0 0 **.* **.* udp6 0 0 localhost.ntp **.* udp4 0 0 practivate.adobe.ntp **.* udp6 0 0 localhost.ntp **.* udp6 0 0 *.ntp **.* udp4 0 0 *.ntp **.* udp6 0 0 *.mdns **.* udp4 0 0 *.mdns **.** udp4 0 0 *.** **.** udp4 0 0 *.** **.** omitted a few asterisks, basically all the empty spots are asterisks what is up with all the UDP connections listening on any port? is that what this means? the internet activity that should be going in is that i connected via wpa to wifi at a small restaurant visited a few pages, checking mail from a few different accounts, no new mail or downloads where done. ?

  Read the article

• Why is REMOTE_ADDR only sometimes available as an Apache environment variable?

  - by Xiong Chiamiov

  To avoid having to parse X-Forwarded-For in Varnish, I'm trying to just set a header on the SSL terminator (currently Apache) that stores the direct client IP in a header. On our development machine, this works: RequestHeader set X-Foo %{REMOTE_ADDR}e However, in staging it doesn't. Specifically, the header is empty, as illustrated by both varnishlog: 13 TxHeader b X-Foo: (null) (On the development machine, this shows the IP address as expected.) Similarly, logging REMOTE_ADDR shows that it only appears to be populated on the dev machine: # Config LogFormat "%{X-Forwarded-For}i %{REMOTE_ADDR}e" combined CustomLog "/var/log/httpd/access_log" combined # Log file, staging <my ip> - # Log file, development <my ip> <my ip> Since the dev machine is, well, a dev machine, it is different in a number of ways; however, I can't track down which difference is causing this. The versions of Apache are the same (2.2.22), and I don't see anything relevant in any of the standard config files or /etc/sysconfig/httpd. And the rest of the system is reasonably similar, since they're built off the same CentOS 5 base image. I can't even tell from the Apache documentation whether REMOTE_ADDR is expected to exist or not as an environment variable, but it clearly works on one machine, whether by fluke or design, and the inconsistency is driving me mad.

  Read the article

• 3 simple questions about file permissions

  - by Camran

  1- Wonder, is this a good setup of permissions in the /var directory? drwxr-xr-x 2 root root 4096 2010-05-30 03:34 backups drwxr-xr-x 7 root root 4096 2010-05-29 17:55 cache drwxr-xr-x 29 root root 4096 2010-05-29 17:55 lib drwxrwsr-x 2 root staff 4096 2009-07-14 04:36 local drwxrwxrwt 3 root root 60 2010-06-02 03:34 lock drwxr-xr-x 9 root root 4096 2010-06-02 03:34 log drwxrwsr-x 2 root man 4096 2009-09-20 20:36 mail drwxr-xr-x 2 root root 4096 2009-09-20 20:36 opt drwxrwxrwt 12 root root 420 2010-06-02 12:12 run drwxr-xr-x 4 root root 4096 2009-09-20 20:37 spool drwxrwxrwt 2 root root 4096 2009-07-14 04:36 tmp drwxr-xr-x 14 user root 4096 2010-05-30 22:21 www 2- Could you give me a brief explanation of the columns above? First one is which permissions they have. Second is a nr. Third and fourth says "root root" for example. fifth is another nr (4096 for example). and the others are obvious. 3- Could you give me a brief explanation of the folders above? Especially the "lock" and "tmp" folders. Lock contains an apache2 folder which seems empty. Thanks

  Read the article

• Ubuntu server apt-get says "(-5 - No address associated with hostname)"

  - by Srini

  I have a ubuntu 12.04 server. Running sudo apt-get update on it produces errors like this: W: Failed to fetch http://au.archive.ubuntu.com/ubuntu/dists/precise-backports/main/binary-i386/Packages Something wicked happened resolving 'au.archive.ubuntu.com:http' (-5 - No address associated with hostname) I am able to ping all the other hosts on the network and also Google's DNS 8.8.8.8. But am unable to ping www.google.com. So, I'm guessing something is wrong with my DNS setup, but not sure what. I use static IP and my /etc/network/interfaces looks like this: auto eth0 iface eth0 inet static address 192.168.1.50 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.0.255 gateway 192.168.1.1 #dns-nameserver 203.12.160.35 203.12.160.36 #nameserver 203.12.160.35 203.12.160.36 My /etc/resolv.conf and /etc/resolvconf/resolv.conf.d/base are both empty and my /etc/resolvconf/resolv.conf.d/original says: nameserver 192.168.1.1 Any help would be greatly appreciated. P.S. I've googled it a bit and the common resolution is to switch to DHCP which I don't want to do since this is my home server. Thanks Srini

  Read the article

• DNS resolve .com domain on local domain

  - by Joost Verdaasdonk

  I'm building a local 2008 R2 domain as a test case to be able to write a roadmap for the real new domain that needs to be created soon. What I would like to know if I'm able to make a record in DNS that will point the domain name: www.example.com and example.com to one of the servers in my network. I tried creating an a-record for it but that doesn't work. To be honest I'm not even sure if this is possible? So can I do this? That way I would be able to fully test all our services (and webb app) offline before I build the real domain and switch the DNS records at the provider. Some advice if possible and where to start is appreciated. The solution (Thanks Brent): Create new Forward lookup zone pointing to example.com Create empty A record pointing to IP of the webserver you are targeting If www is needed create A record with Name: www and IP of your webserver sub domains repeat the process but then with names for example: sub or www.sub (and ip your webserver) Be aware of the DNS Cache while you are in this process. Things can take time or do the following: Right click the server and choose clear cache in CMD: ipconfig /flushdns (to flush the client cache)

  Read the article

• How to tell nginx to honor backend's cache?

  - by ChocoDeveloper

  I'm using php-fpm with nginx as http server (I don't know much about reverse proxies, I just installed it and didn't touch anything), without Apache nor Varnish. I need nginx to understand and honor the http headers I send. I tried with this config (taken from the docs) but didn't work: /etc/nginx/nginx.conf: fastcgi_cache_path /var/lib/nginx/cache levels=1:2 keys_zone=website:10m inactive=10m; fastcgi_cache_key "$scheme$request_method$host$request_uri"; /etc/nginx/sites-available/website: server { fastcgi_cache website; #fastcgi_cache_valid 200 302 1h; #fastcgi_cache_valid 301 1d; #fastcgi_cache_valid any 1m; #fastcgi_cache_min_uses 1; #fastcgi_cache_use_stale error timeout invalid_header http_503; add_header X-Cache $upstream_cache_status; } I always get "MISS" and the cache dir is empty. If I uncomment the other directives, I get hit, but I don't want those "dumb" settings, I need to control them within my backend. For example, if my backend says "public, s-maxage=10", the cache should be considered stale after 10 secs. Instead, nginx will store it for 1h, because of these directives. I was thinking whether I should try proxy_cache, not sure what's the difference. In both fastcgi and proxy modules docs it says this: The cache honors backend's Cache-Control, Expires, and etc. since version 0.7.48, Cache-Control: private and no-store only since 0.7.66, though. Vary handling is not implemented. nginx version: nginx/1.1.19 Any thoughts? pd: I also have the reverse proxy that is offered by Symfony2 (which I turn off to use nginx's). The headers are interpreted correctly by it, so I think I'm doing it right.

  Read the article

• Force request to miss cache but still store the response

  - by Tom Marthenal

  I have a slow web app that I've placed Varnish in front of. All of the pages are static (they don't vary for a different user), but they need to be updated every 5 minutes so they contain recent data. I have a simple script (wget --mirror) that crawls the entire website every 15 minutes. Each crawl takes about 5 minutes. The point of the crawl is to update every page in the Varnish cache so that a user never has to wait for the page to generate (since all pages have been generated recently thanks to the spider). The timeline looks like this: 00:00:00: Cache flushed 00:00:00: Spider starts crawling to update cache with new pages 00:05:00: Spider finishes crawling, all pages are updated until 1:15 A request that comes in between 0:00:00 and 0:05:00 might hit a page that hasn't been updated yet, and will be forced to wait a few seconds for a response. This isn't acceptable. What I'd like to do is, perhaps using some VCL magic, always foward requests from the spider to the backend, but still store the response in the cache. This way, a user will never have to wait for a page to generate since there is no 5-minute window in which parts of the cache are empty (except perhaps at server startup). How can I do this?

  Read the article

• Cacti Login Page: Infinite loop occurs

  - by beicha

  Apache 2.2.3 | PHP 5.1.6 | MySQL 5.0.77 I followed cacti installation guide to install latest cacti 0.8.7h on CentOS 5.5 (64-bit). The installation of PHP/Apache/MySQL went smoothly until I finished the setup, and came to the login page. I can login http://.../cacti/index.php with admin account but the new page is redirected to the same login page with the message "Please enter your Cacti user name and password below" This is a infinite loop! If I use a wrong admin password I get the correct error message "Invalid User Name/Password Please Retype". [Same problem here] If I login use Guest/guest account, "Error: Access Denied, user account disabled." displays. The Cacti log file (./cacti/log/cacti.log) is empty. I Googled and seems this problem has existed for a long time, but no followup solutions were found on the forum posts I found. Anyone can help me on this problem? If more information needed, please let me know. Nov 18, 2011 UPDATE: I re-installed Cacti, this question remains UNSOLVED.

  Read the article

• How to migrate Outlook Express mail rules?

  - by ronwest

  I have a home computer that only had a 15Gb C: drive, and ran out of space with all the Microsoft Updates, etc, that keep coming down. So I fitted a 160Gb drive as a C: drive and altered the drive jumpers to make the old C: drive into a slave D: drive, to save migrating documents, etc. I've installed a clean copy of Windows XP SP3 and reassigned the new Outlook Express' mailstore path to point to the old mailstore folder that now has a D: drive letter - and it all works OK. However, my extensive list of mail rules have not been transferred to the new OE and I have not been able to identify how they are stored. To find it I added a new rule to the new OE, exited OE, then searched on the whole computer (including hidden/system files) for files altered around the time I added the rule. I hoped I could just overwrite a new empty file with an old one. But the only files that seem to be changed are Windows system-level files and some bits and pieces in the Windows\PreFetch sub-folder. None of them can be opened as XP has them locked, and none of them have names that are anything to do with email or rules. Does anyone know of any way of migrating OE rules, or do I have to re-enter them by hand? Thanks!

  Read the article

• How to recover my invisible HD again?

  - by pattulus

  I made this several times now, but this time something bad happened. What I did: I installed Windows 7 at a 32GB partition on my slot 2 HD in my MacPro. Windows 7 made a 105MB partition… I knew this before, but what I didn’t know was that this partition is now on my slot 4 HD. My home folder, my private videos and some other stuff are on this 1TB drive. What I found out so far: I’m currently logged in as another admin since my OS partition as well as the two other HD's aren't harmed. Disk Utility: … only shows the 105MB NTSF partition on this 1TB volume. It isn’t showing my old 1TB partition/ex-HD named "storehouse". Only the partition tab is telling me that there now is a 1TB empty free unpartitioned space. Data Rescue II: … is showing the Volume as it used to be with it's old Name "storehouse". A quick scan and a thorough scan both were done in 1 second which leds me to the conclusion that there's isn’t something deleted at all (» hope!). Data Rescue doesn’t even mention the damn "system reserved" partition. Drive Genius: … also shows the old partition and doesn’t mention the new one. But looking at the info it tells me under "content": FDisk_partition_scheme (instead of Apple_partition_scheme). Well D'oh…. Tech Tools: … doesn’t show the volume, otherwise I'd might have been tempted to press rebuild/repair. What to do next?? I think the best approach is to buy another 1TB HD and let Disk Warrior Clone my old one to it… just to be on the safe side. But what is the best thing to do after this… ???

  Read the article

• How to handle files that don't need version control in mercurial

  - by richardh

  I am new to mercurial, and for the most part do LaTeX reports and statistical calculations in R using .csv and/or .sqlite files. Re LaTeX, all I really care is the .tex file. Re R, I don't need version control on the .csv or .sqlite files because they are static. When I do 'hg add' for a repo with a .csv and/or .sqlite file, I get a warning like: rev2.sqlite: up to 3070 MB of RAM may be required to manage this file (use 'hg revert rev2.sqlite' to cancel pending addition) So I revert and subsequently use adds like hg add -X *.sqlite. I guess I really have two questions: (1) Should I ignore these warnings? Because these large files are static, can I just add to the repo knowing that the diff files will always be empty and not worry about wasted resources? (2) If I should keep excluding these files from the repo, is there away that I can fix this option? I.E., add to my .hgrc file something that always appends an option like -I *.tex -I *.R to my 'hg add' commands? Thanks!

  Read the article

• How can I read PDFs with e-reader on a Lenovo tablet?

  - by Jack M

  This is my first time using a tablet and I'm totally lost - this must be what computers look like to old people. This is a Lenovo Thinkpad tablet. I don't see a specific model number on it (it was passed down to me second hand). What I'd like to do is read a PDF. I'm fairly certain I successfully transferred the PDF onto the tablet via an SD card, and I noticed this thing has an app called "eReader" on it, so I started that up. All I see are empty bookshelves, and no obvious buttons or settings anywhere. I saw in multiple places that you have to, as one site puts it: ...copy and paste the relevant files into the eBooks folder and they will appear on the eReader shelf for your consumption... But I have no idea how to: Access the file system. Locate the eBooks folder. Copy and paste files. Will I need a file explorer app? If so, how can I install that given that my only method of getting data onto this tablet is an SD card (no wireless internet).

  Read the article

• TFS 2010 Subfolder Permissions

  - by gmcalab

  I am a TFSAdmin and when I have a TFS project in which a subfolder needs specific permissions to deny some users. So, I right click on the folder in question hit Properties, and click the Security tab. There I select the Windows User or Group radio, then click Add. I put in the AD User that I want specific permissions for and hit Check Names. That resolves, so I click OK. Next, I select the permissions to Allow or Deny below in the Permissions for list. I hit OK. The permission are honored by TFS, this user no longer has PendChange permissions and I was expecting. The odd thing is, I was expecting to be able to go back into the Security tab and see that User in the list of Users and Groups and see the current state. But the list is always empty. Not sure why, but the permissions are definitely being honored, I can re-add the user with different permissions and those are also honored. Any ideas why the current users are not showing up in the Users and Groups list under the Security tab for a folder's properties? I also used the tf permission $\... to see if there were any permissions but it always returns There are no permissions set for this item (Inherit: Yes)

  Read the article

• Why Would one VLAN have no Communication on one Switch?

  - by Webs

  So the problem is we have a device or host that needs to communicate on a specific VLAN. This VLAN is not new, it is running all throughout our environment and works fine. But the VLAN was recently configured on the switch in question, a Cisco 3750. The DHCP server is handing out addresses on that VLAN with no problem. I have verified the cable between the host and switch and tried multiple hosts, but none of them can communicate or get an address. I plugged my laptop into an empty port which had a different VLAN assigned and immediately got a DHCP address. When I changed that port to the same VLAN I'm having issues with I got the same problem. The laptop just sits there and tries to DHCP an address but nothing happens. I double checked the cores and their Layer 3 VLAN config and its fine too. Plus I figured the issue couldn't be with them because the VLAN works fine everywhere else it exists. So the only other thing I can think of is the switch, but the VLAN exists on the switch and seems to be configured correctly. The trunks appear to be configured just fine as well too. Anyone have any ideas? I'm lost on this one.

  Read the article

• FTP account ownership on vhost directory makes Apache not run website correctly

  - by CodeShining

  I've purchased a virtual server, where I'm given of a non-root sudo-enabled user. Actually I do need to create an FTP account that's not that sudo-able account, so I created a no-login account just for that purpose. I've set up VSFTPd correctly, also enabling the "userlist" feature, to specify which user are permitted to use FTP. Then I created an empty directory under my sudo-able account, and I gave ownership permissions to the second account, so to make it more easy to understand, let's say the main account (the one I do use to manage my VPS) is called ubuntu and the FTP-user is named ftpuser, I created a directory /home/ubuntu/mywebsite giving the ownership to ftpuser:ftpuser. Then I uploaded a worpdress website, whose default permissions are 755 and 644. The issue is that Apache is not given of any privilege to run the website. How can I make the website run properly, and which is the most secure? Should I run that virtualhost with another user (if it's possible)? Should I force the FTP user to use the www-data group (if that's possible) and run with permissions like 775 and 664? How can I solve this issue? Any help is appreciated, I'd like to run it using the default permissions, so any update won't break up anything (because of permissions reset).

  Read the article

• pcfg_openfile: unable to check htaccess file, ensure it is readable

  - by rxt

  After moving a website folder on my local development machine to another drive, then moving it back, I got a 403 error. Most of this problem had probably to do with rights that got messed up. After deleting the code and restoring it from SVN, the rights seemed allright. The error stayed however. The setup is a bit complex, as follows: I have Ubuntu 10.4 as development machine, trying to mimic the server as much as possible We use Eclipse + SVN and I create all projects in a local folder under my user account In /var/www-vhosts I create folders for each vhost, like this one: test.localhost test.local/index.php: includes the index file of the project test.local/.htaccess is a dynamic link to the htaccess file in a project subfolder I get the following error in the apache error log: [Thu Jul 08 15:55:56 2010] [crit] [client 127.0.0.1] (13)Permission denied: /var/www-vhosts/test.localhost/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable The problem seems to be the .htaccess file, or the link to it. When I empty the htaccess, nothing changes When I remove the link, the index-include produces some output (in the apache error log) When I remove the link and replace it with the actual file, I get another error: [Thu Jul 08 16:47:54 2010] [error] [client 127.0.0.1] Symbolic link not allowed or link target not accessible: /var/www-vhosts/test.localhost/test I'm lost here, don't know what to do next. Do you have any ideas what I can try? This setup has worked before, but I don't know what is different now.

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem. EDIT: In the end, nothing really worked, and I got really annoyed with the state of compiz and its support in Debian. Many nVidia driver revisions have passed and I am using Gnome 3 now, so I am accepting the best answers to this question even though the issue was not resolved.

  Read the article

• iptables blank after reboot

  - by theillien

  We've started encountering an issue with iptables on our RHEL 6.3 systems in that after a reboot, when the service starts, the rules are not loaded. We get the empty ruleset: [msnyder@matt-test ~]$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination This is in spite of the fact that we have rules defined and the service is, indeed, running. That I know because when I run service iptables start it simply drops back to the prompt. If I run service iptables restart it actually stops and then restarts the service. And, of course, if I run service iptables stop it indicates that iptables is actually stopping. Knowing that I need to restart the service, I do so and the rules load up properly. They simply don't get loaded after a reboot. Unless they get loaded differently during a reboot I don't see how our rules would be wrong. If they were, they wouldn't even load during a service restart. Has anyone else ever encountered this? EDIT: The rules are already saved in /etc/sysconfig/iptables. They are not added on the fly from the command line so service iptables save is unnecessary.

  Read the article

< Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >