Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 218/391 | < Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >

• Most secure way to have IPtables auto-loaded using Debian / Linux

  - by networkIT

  I'd like to know the safest way to load iptables using Debian. Of course, I can use a script that uses iptables-restore : #!/bin/sh iptables-restore < /etc/firewall.conf but : 1) where is the safest place to have it loaded ? /etc/network/if-up.d ? I'm concerned about the script being loaded early enough at boot time, and reliably enough when plugging/unplugging interfaces ... 2) is this script method using iptables-restore the most secure way ? 3) additionnally, how much does the answer validity stretch to other Linux distros ( Ubuntu, Fedora, CentOS ) ? Thanks ^^

  Read the article

• Multicast Prblem in Linux Red Hat server

  - by Uma Kant Verma

  I am facing a very strange behavior on my server. I am using a linux cluster.On fail over server my broadcast application halts after 5 minutes.But it is working fine on Primary server. My application process listening on port and send broadcast.It is working 5 mins after that it wait on socket for further packets but it didn't receive anything. Same process is working fine at Primary server. Plz help me.

  Read the article

• Unidentified network: How to configure TCP/IPv4 for Win7?

  - by Zolomon

  When I try to connect to internet I keep getting the error "Unidentified network". I've tried numerous attempts at restoring access without success. IP release, flushing DNS cache, reinstalling NIC, reactivating NIC, resetting router and so on... I've read several times that it's my default gateway that's wrong. Currently I've had automatic IP/DNS configuration set without any problems, and then it stopped working for some reason. Anyone know how I specify the IP? My subnetmask is 255.255.255.0, default gateway is 192.168.0.1 but I have no idea how to determine what IP I should set. I use a D-Link DIR-655 and other computers on the network have IPs like 192.168.0.194, next is 192.168.0.197. (I'm completely lost and am trying to cool down after two weekends of debugging filled with despair.)

  Read the article

• No file sharing between two server 2008 R2 machines.

  - by ProfKaos

  I have just replaced XP with Server 2008 R2 on my test sever, and have been running 2008 R2 on my dev laptop. When my server was still XP, file sharing just worked, but now it just doesn't. I've enabled everything I can about sharing, and I can ping the server by machine name, but if I try an access a share, I get asked for a password. The passowrd dialog assumes a domain for this user, but neither my laptop admin user nor my server admin user can get past this login. What am I doing wrong?

  Read the article

• How do I stop someone from saturating my line & wasting CPU cycles

  - by JoshRibs

  My web host shows inbound & outbound traffic with mrtg. I have a steady 3.5mbps inbound traffic from Nigeria. Even assuming the source IPs & destination ports are blocked with Iptables & verifying nothing is listening on those ports, will the traffic still always pass through the switch & "get" to my server (where my server wastes CPU cycles "dropping" the packets)? Assuming I was setup with a hardware firewall, the traffic would still show in mrtg assuming the firewall is behind the switch? So is there any way to stop someone from saturating your 100mbps line, if they also have a 100mbps line? Other than filing an abuse complaint with the kind folks in Nigeria?

  Read the article

• Using Hamachi VPN to connect to Linux VM at home

  - by Cameron Verotti

  I have a CentOS 5.10 Linux box at home running on VMWare, with Windows 2008 as the host. I have set up a Hamachi VPN so that I can connect to the Host server from work, I attempted to add a second VNIC to the VM and bridged it to the hamachi Network Interface. I spun up the VM and checked eth1 with ifconfig and its throwing me a ipv6 address not a ipv4. I want to hook this VM up so that I can run a ssh command from work to the VM. MY network at home is all on Local 198.168.. hence the need to make a VPN network like Hamachi. I cannot seem to find anything that tells me or helps me with tunneling my Linux VM via Hamachi. Any help would be fantastic!

  Read the article

• Share ADSL Internet connection between two computers 40 meters away (straight) from each other

  - by dario_ramos

  I have a box with a working ADSL Internet connection. About 40 meters away (straight), in another house, there is another, older box. There are two houses in between. Would there be some practical way to supply an Internet connection to the older box? The neighbors are ok with us installing cables and stuff. I'd say wifi would not be practical, since the houses in between would weaken the signal too much. And using Ethernet cables might require a switch or router in between, due to Ethernet distance limitations. Advice?

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• How do I tell Windows to use 802.11 in preference to 3G?

  - by Jon Skeet

  I have a Samsung NC-10 netbook which I take to work every day. Most of the time I use it just on the train/bus, but I also use it at work and home. It has a built-in 3G card which I want to use when travelling, but I'd prefer to use wifi when I'm at work or home, for obvious reasons. Unfortunately, if the 3G connection is up, Windows appears to use that in preference to wifi. Starting up and shutting down the 3G modem is a bit of a pain - it's not hard as such, just a bit inconvenient. Ideally I'd like it to always be up, and even have the connection itself up all the time, but without routing traffic through it if there's a wifi connection up. This is what my Android phone does, for example. Is there somewhere in Windows which lets me express an ordering for network interfaces? I suspect the routing table may be relevant, but it's a bit of a pain to mess around with. I'd really expect there to be a simple GUI way of setting this up - after all, it would equally be useful when dealing with wired vs wifi connections. I'm currently using Windows XP Home, but Windows 7 answers would also be useful as I'll be migrating soon.

  Read the article

• Internet setup for my office

  - by prakash

  We have two internet connections to our office and our current setup is like this.. The internet connections require pppoe log in so i take each cable and plug it into a wifi router and configure the router to log in to the pppoe and then plug in a cable from the router to a switch and distribute the internet throughout my office. The problem with this setup is it is really hard to monitor and im not able to monitor who is hogging internet usage and what he or she is actually using it for. apart from this we also have a nas setup which is routed through another switch . Could someone please throw a little light on how i can restructure this setup for easy monitoring and better transparency... ? each wan router is connected to a different switch and is distributed to users accordingly.. we have around 40 users in the office.. we want to setup a single linux box to which i want to connect the two wan connections and from there distribute it to all our users.... im looking for a solution where we do not have to invest more that buying a single pc and a couple of nics

  Read the article

• What to do if people can't ping me?

  - by slayerIQ

  Today, I installed my new router so I can connect my other pc and my ps3. In my network, there are some other computers these are connected with each other through another router. So I have one modem with 2 routers that make up my network. Everything works fine the only problem I am having is being pinged by other computers in the network. All the computers are on the same subnet 255.255.255.0. There is no problem with my firewall or anything I tested everything. How can I solve this?

  Read the article

• What are the different ways of remotely connecting to your computer?

  - by Rogue

  I'll be leaving for uni soon and would like to know the different methods of connecting remotely to my home pc. I know about VPN but are there any other ways? Also how secure is each of this method as I wouldn't want snoopers on my home-pc especially when I'm away. Also can i set up a remote connection to start and shut down my computer My operating system is windows, but if linux is more secure i would be willing to switch.

  Read the article

• How to combine AWS and dedicated external servers?

  - by rfw21

  I have an extensive network of servers all currently hosted on AWS EC2. For reasons of cost I plan to gradually migrate to dedicated servers where possible. So: How can I best combine AWS and non-AWS servers in my network? Ideally, I should be able to assign internal IP addresses to the external servers, include them in AWS security groups and ensure that all private traffic between my AWS servers and external servers is secure.

  Read the article

• Unable to set initcwnd on a Hetzner server

  - by Sergi

  We just ordered a bunch of Hetzner EX40SSD servers with the minimal Debian install image that they provide and everything is just fine except that looking at tcpdumps for fine tuning the network from various locations the initcwnd param seems to be stuck at 6 no matter how we change it. By default Debian 3.2 kernels should have that setting to 10 so it's pretty strange. Is it possible that the NIC driver or a custom setting in the Hetzner Debian image is limiting this param? Even if we set it to 4, like the old kernel default, it doesn't work. Any ideas would be much appreciated! Does anyone know if the NIC drivers provided by default by Debian have some kind on limitation. In a long thread in http://www.webhostingtalk.com/showthread.php?t=1200617&highlight=hetzner they talk about a page http://wiki.hetzner.de/index.php/Installation_des_r8168-Treibers/en where Hetzner states that the included Realtek r8168 driver is not working properly, but nowhere do they say that the initcwnd could be affected. Tomorrow i will try to install a CentOs image and see if Debian is the problem...Last resort would be to install a custom debian image, but that is a pain in the ass! Thanks!

  Read the article

• Why can't a PC with 2 network cards be accessed by hostname?

  - by lewis

  I set up PC with 2 network cards, connected to the same LAN. I can connect to this PC (e.g. by remote desktop) only via ip-addresses. Accessing by hostname does not work. Why is this the case? UPDATE: Full environment 1. PC with 2 hardware network adapters. 2. On this PC installed VMWare Workstation. Created 3 VM's, networked by "bridged" network setting in VMWare. 3. In LAN all ip-addresses given from DHCP. 4. Win2k8 on all hosts (both physical and vitrual). As result: 1. PC has 2 ip-address (e.g. 192.168.1.71 and 192.168.1.72). PC available in LAN by ip-addreses, but not avail by hostname. 2. VM's has own ip-addr on each (e.g. 192.168.1.73, *74, *75 etc). They are available from LAN by their ip's, BUT not by their hostnames. How can I access to PC and to VM's by hostname?

  Read the article

• Find if IP Address is in use

  - by WedTM

  I'm trying to find if an IP address is in use. I don't want to rely on ping, as most of our hosts have ICMP echo and reply turned off. I'm looking for something that mimics window's "IP Address Conflict" detection. (How does this mechanism do it?)

  Read the article

• How to secure a group of Amazon EC2 instances

  - by ks78

  I have several Amazon EC2 instances running Ubuntu 10.04 and I've recently started using Amazon's Route 53 as my DNS. The purpose of doing that was to allow the instances to refer to each other by name rather than private IP (which can change). I've pointed my domain name (via GoDaddy) to Amazon's name servers, allowing me to access my EC2 webservers. However, I noticed I can now access the EC2 instances which I don't want to be public, such as the dedicated MySQL Server. I was thinking Amazon's Security Groups would still be in effect when using Route 53, but that doesn't seem to be the case. Before I started using Route 53, I was thinking of having one instance run a reverse proxy, which would help protect the web servers behind it. Then IP-restrict all the other instances. I know IP restricting can be done using the firewall within each instance, but should I ever need to access them from another IP address, I'd need a way in. Amazon's control panel made it a breeze to open a port when necessary. Does anyone have any suggestions for keeping EC2 instances secure, but also accessible to their administrator? Also, what's the best topology for a group of EC2 instances, consisting of web servers and a dedicated database server, from a security perspective? Does having a reverse proxy server even make sense?

  Read the article

• XP - ping changes routing table?

  - by Corelgott

  Hey Folks, I have got a real strange behaviour with one of my XP-Sp3 machines. Setup: A Server in the lan (192.168.5.0) proviedes access to all roadwarriors in 10.8.0.0 The DCHP has a static route for all clients pronouncing 192.168.5.235 as gateway for 10.8.0.0 All Clients can ping & access the vpn-machines; everything works like a charm But one Xp-Sp3 is not willing to connect to them. It gets all the same routes as any other sytem in the lan and I trippel-checked - there are no static routes on this machine When I ping any 10.8.0.0 device from this machine, the first two packaged work like a charm; but the next two (and any package after them) fail and get lost. When I look back into the routing table: There is a new route; a special one just for the device I pinged, which points to the right gateway - but which wasn't there earlier... As Long as this route exists the machine can't ping anything on 10.8.0.0. But if I remove the route by hand: The next to ping packages work fine... Has anybody got an idea about that? Anybody every seen such a behaviour? Any hint / help / tip is greatly appreachiated! thx in advance Corelgott Ps: I attach an image of the cmd to clarify things - its in german, but reading a routing table shouldn't be that hard...

  Read the article

• Issue about mapping MAC address to Ipv6 address

  - by deepsky

  I know that the address in ipv6 with prefix range 001 to 111 should use a 64-bit interface identifier that follows the EUI-64 format, which translates the MAC to ipv6 as below. MAC:00-02-b3-1e-83-29 --> 02-02-b3-ff-fe-1e-83-29 --->ipv6 addr: fe80::202:b3ff:fe1e:8329 Then I checked my network status with ipconfig /all on my windows XP, but it seems my ipv6 address doesn't follow the above rule: MAC:00-24-81-XX-XX-XX ipv6 addr:2001:da8:8006:225:0:24:81XX:XXXX Obviously it doesn't follow the EUI-64 format. Instead it just directly use the MAC as the last 8 bytes. Anyone know the reason? Pls Correct me if I am wrong.

  Read the article

• windows: force user to use specific network adapter

  - by Chad

  I'm looking for a configuration/hack to force a particular application or all traffic from a particular user to use a specific NIC. I have an legacy client/server app that has a "security feature" that limits connections based on IP address. I'm trying to find a way to migrate this app to a terminal server environment. The simple solution is for the development team to update the code in the application, however in this case that's not an option. I was thinking I might be able to install VMware NIC's installed for each user on the terminal server and do some type of scripting to force that user account to use a specific NIC. Anybody have any ideas on this? EDIT 1: I think I have a hack to work around my specific problem, however I'd love to hear of a more elegant solution. I got lucky in that the software reads the server IP address out of a config file. So I'm going to have to make a config file for each user and make a customer programs files for each user. Then add a VMware NIC for each user and make each server IP address reside on a different subnet. That will force the traffic for a particular user to a particular IP address, however its really messy and all the VM NIC's will slow down the terminal server. I'll setup a proof of concept Monday and let the group know how it affects performance.

  Read the article

• Setting up a linux switch

  - by Shahmir Javaid

  I have a C++ Program to sniff each and every packet that crosses my linux box. However i need to now get my linux box to listen to every traffic in my network. I could buy a managed switch and set up port spanning, but i aint paying 200+ £'s for a switch and plus gives me a chance to learn. My Network +---------Computer A | Internet-----Router------Switch-------------+---------Linux Box | +---------Computer B Proposed Network +---------Computer A | Internet-----Router------Linux Box--------Switch eth0^ ^eth1 | +---------Computer B How would i setup this in linux. Do i just configure both the ethernet on different IP Address on the same network. Or am i completelly on the wrong track My System Fedora 13. Thanks

  Read the article

• Set source address to use tun device does not work (Debian Squeeze)

  - by A. Donda

  there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

  Read the article

• Building a network at home, what cables to use (if any)?

  - by Faruz

  My house is currently in ruins and am building it. While doing so, I wanted to design a home network. My main objectives are surfing and HD streaming. The house is one-level, 100 sq/m (about 300 sq/ft), and one of the rooms is a safety room with Reinforced concrete walls. About a year ago, when I started planning, I thought about putting Cat 6 STP cables in the walls and create network points in the rooms. Should I use STP or FTP? I heard that STP is a problem regarding connectors and stuff. Is it really beneficial? Will it work OK if I transfer the wire together with the telephone line? Should I maybe go with WLan and count on 802.11n to enable me to stream HD across the house? is 802.11n that good?

  Read the article

• Windows 7 can't identify network

  - by Carl Hörberg

  I use a Windows 7 machine to share my internet connection, but the one network interface which are connected to my local network is marked as "Unidentified network", the sharing works well anyway but because the interface can't be chosen as Home network i can't use the HomeGroup features etc. Do you know which requirements an interface has meet to identify a network in Windows 7?

  Read the article

• Several border firewalls in the same network

  - by nimai

  I'm currently analyzing the consequences of multipath connections for the firewalls. In that context, I'm wondering if it's really uncommon to have several firewalls at the borders of a network to protect it. The typical case I'd imagine would be a multihomed network, for which the administrator would have different policies for links from different (or not) ISPs. Or maybe even in an ISP's network. What would be the practical (dis)advantages of such a configuration? Could you provide an example of an existing topology using several border firewalls?

  Read the article

< Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >