Search Results

Search found 8410 results on 337 pages for 'hardware reserved'.

Page 219/337 | < Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >

• Screen flickers after resuming from hibernate with Intel GMA 3600 (Acer D270 with Intel N2600)

  - by Cameron

  Fresh system install, with correct display driver from Intel (8.14.8.1065). Clicking "Update driver" merely results in a message saying the driver was already up-to-date. After resuming from hibernate the entire screen flickers. This is especially noticeable while using IE9 (which has hardware acceleration enabled by default) on Google maps, in particular while typing in an address in the map search field (the flickering is much worse under these circumstances). Note that sleep worked fine, only hibernate causes this issue. Restarting "fixes" the problem temporarily until the next hibernate-resume. Aero is enabled. This is on Windows 7 (Pro) 32-bit, on an Acer Aspire One D270-1998, with the Intel N2600 (which has the Intel GMA 3600 built-in).

  Read the article

• ZFS SAS/SATA controller recommendations

  - by ewwhite

  I've been working with OpenSolaris and ZFS for 6 months, primarily on a Sun Fire x4540 and standard Dell and HP hardware. One downside to standard Perc and HP Smart Array controllers is that they do not have a true "passthrough" JBOD mode to present individual disks to ZFS. One can configure multiple RAID 0 arrays and get them working in ZFS, but it impacts hotswap capabilities (thus requiring a reboot upon disk failure/replacement). I'm curious as to what SAS/SATA controllers are recommended for home-brewed ZFS JBODs. In addition, how does battery-backed write cache (BBWC) play into the solution?

  Read the article

• Are there significant performance difference between chipsets?

  - by Let_Me_Be

  I wanted to build a single PC to fit all my needs, but since hardware virtualization support (Vt-d specifically) is a huge problem, I decided to build multiple single-use oriented computers. In this scenario I want these computers to be as minimal as possible. So the core of my question is: "Are there significant performance difference between chipsets?" I'm considering Sandy-Bridge i7 or i5 for my "game console" computer. And since I will use only one graphic card, one or two HDD, 4-8GB RAM and nothing else, I would be fine with a micro-ATX board with a Q67 (or some other low-end chipset).

  Read the article

• Windows replacement for HAProxy

  - by GrayWizardx

  It does not appear that there is a similar question to this already posted, so I will go ahead and ask. I am working on a project that could benefit from having two - four servers handling incoming requests to a backend webservice. The service does not require SSL but does need to support occassional long running processes (upto 120 secs). This project does not at present have the funding to purchase a hardware load balancing solution. I have previously used HAProxy as a solution for this, and found it very simple and straightforward. Is there a similar product for windows (server 2003 or 2008) which provides similar configuration options and runs as a lightweight service? For reasons outside my control I cannot setup a Linux machine (physical or virtual) and so I am looking for behaviour that can be deployed on a windows machine. I can only find Perlbal which appears to fall into this category. So as not to keep this open indifenitely I will give credit to the only answer.

  Read the article

• How to make phone calls using a pc, modem, headphone and no actual phone instrument

  - by user18151

  Hi, I have a phone landline connection and I DO NOT have a phone instrument. I connect the cable into my laptop, and want to make calls using my laptop. I have an HDA CX20561 modem. I seem to be able to dial number using dialer.exe, though nothing seems to happen. From Microsoft kb http://support.microsoft.com/kb/958143, it looks like dialer.exe alone is not enough for the call. Can somebody tell me how to make and receive phone call with whatever hardware I have, i.e. what software will I need. Thanks.

  Read the article

• Installing 2 DDR3 Sticks in MB with 4 Slots

  - by The Sasquatch

  Hey everyone, I just put together my first system that uses DDR3 memory. The motherboard I got is an ASUS M4A77T/USB3 and it has 4 DDR3 RAM slots. Looking in the manual for the MB it doesn't say anything about how to install the RAM as far as matching the pairs goes. I have 2 4GB sticks of RAM, and whether I put the sticks next to each other (of the 4 RAM slots, there are two blue ones next to each other and 2 black ones next to each other) or space them apart, The BIOS still shows that I have 8GB installed. I have been getting an IRQL_NOT_LESS_OR_EQUAL BSOD error, and have read in some other places that it could be hardware/RAM related. Does the RAM need to go in the A1, A2 slots (different colored but both A), or the A1 B1 slots? (A1 B1 are both the lovely blue color.) Any help would be awesome. THANKS!

  Read the article

• Can I upgrade a Windows 2000 domain to 2008 and demote the 2000 server without clients attached?

  - by techie007

  Hi all, We're planning to replace a Windows 2000 domain controller with a new 2008 DC (new hardware). We've elected to take the route of getting the 2000 domain schema up-to-snuff, join the 2008 server, upgrade it to a DC, and after replication demote the 2000 server (eventually to be taken off-line). The goal being to not have to visit all the workstations, and limited domain down-time. :) We want bring the old server here and do all the backups, Domain prep, migration and role transfers here, and then (hopefully) just plop the new 2008 back in place after it's done, and join the 2000 server back as a member server (so we can then do folder migrations, etc.). Can this server work be done off-site, without the workstations attached? If we do this will anything need to be done to the clients, once the new DC is physically in place, so they contact the new 2008 DC; or will they just 'know' and continue on using the existing domain settings/user profiles, etc.? Thanks in advance! :)

  Read the article

• Motherboard max memory supported

  - by Ashfame

  I have an Intel DG965RY motherboard and its specification says it supports 8GB with 533 or 667Mhz RAM sticks and only 4GB with 800Mhz RAM sticks. I am running a 64bit OS. I earlier had 2 X 1GB sticks (800Mhz), so I bought 2 X 2GB sticks (800Mhz) and I underclocked them in the settings to run at 667Mhz. Shouldn't it support all 6GB RAM now? It would be a bummer if I will specifically need 667Mhz sticks thinking that at the worst they will underclock and then run at 667Mhz. I tried this because I saw someone posted at some forum that he put in 4GB+ of RAM in the same board @ 800Mhz and the system uses it all. In my case (On Ubuntu), it only shows 3.2GB as of now (link to Question) so needed to confirm if this is a hardware limitation.

  Read the article

• Plesk Backup Best Practices?

  - by The MYYN

  My client utilizes Plesk (9.X) for Server Management. We're implementing a custom backup solution, which should include a complete restorable representation of the actual Plesk configuration (Emails, Domains, etc.). We have full access, since it is a dedicated server resembling these steps: Plesk offers some backups, but they do not include the actual content of the (sub-)domains. Browsing the docs and the internet, I haven't found much ideas on that problem. Our target is to have a disaster recovery scenario: Reinstall a clean OS (Ubuntu) from scratch. Install MySQL/PHP and dependencies (since this runs the app) Install a bare plesk Restore all domains + plesk configuration from an archive Continue operations ... Now steps 1, 2, 3 and 5 are trivial. But what are the best practices for step 4? A side questions: Are there any easy-to-use open source apps out there, to create and restore server-images (even on machines with an possible different hardware)? Thanks for your time and input.

  Read the article

• Can't find generic USB audio driver for a Samson COU1 USB microphone

  - by marcipollo

  I am unable to use a Samson USB CO1U microphone on a PC running XP, SP3. When I plug it into the USB port, Windows generates the sound indicating that it has found new hardware, and the green LED on the mic lights. But, it does not work, and the device manager reports that it cannot find a driver after searching. The same mic works on a Vista machine. Samson has no driver on their Web site, and insists that the generic audio driver in Windows should work. (http://www.samsontech.com/PRODUCTS/productpage.cfm?prodID=1810). I cannot find a generic USB audio driver at Microsoft.com. Can anyone help? Larry

  Read the article

• Quad Core host with hyper-threading, how many processors to configure in VirtualBox?

  - by Anthony

  I have a quad-core i7 processor with hyperthreading (8 logical cores), when I configured a virtual machine to use 8 processors, VirtualBox gave me a warning saying that I only have four cores (which is true) and that this may cause a performance issue. But hyper-threading is a hardware feature, so the OS sees 8 cores and it sends instructions to all 8. What if setting it to 4 caused the VM to use 2 cores (4 threads) instead of 4 simultaneous threads (on all 4 cores)? Does the warning I got take into account that my machine has hyper-threading?

  Read the article

• How do I fix "Setup did not find any hard disk drives installed in your computer" error during Win X

  - by CT

  I just bought a nettop. It came with WinXP Home. I first installed Win 7 on it. I wasn't that happy with the performance so I decided to go back to XP. I am using an external dvd drive and a Win XP Pro disc. I boot from the dvd drive and during the install get this error: Setup did not find any hard disk drives installed in your computer. Make sure any hard disk drives are powered on and properly connected to your computer, and that any disk-related hardware configuration is correct. This may involve running a manufacturer-supplied diagnostic or setup program. Setup cannot continue. To quit Setup, press F3. This is the nettop in question: http://www.newegg.com/Product/Product.aspx?Item=N82E16883103228

  Read the article

• 64 Bit Windows drivers for Inspiron 1720

  - by Rob Allen

  Dell doesn't seem to offer 64 bit drivers specifically for the Inspiron 1720 (laptop). I'm going to be upgrading from Vista 32-bit to Windows 7 64bit and I want to pull down the necessary stuff before hand. Are there any Dell systems that are similar enough to the Inspiron 1720 that I can use for a baseline to make sure I still have Ethernet and WiFi after the reinstall? It doesn't matter if they are for Vista 64 or Windows 7. Identified hardware: Processor: Intel mobile Core 2 Duo T7500 Chipset: Intel Mobile 965 Express Wifi: Intel Pro Wireless Drive Controller: Intel Matrix Graphics: nVidia GeForce 8600M GT Bluetooth: Dell TrueMobile 355 + EDR Ricoh card reader I think anything else, the default Windows drivers will be sufficient. Let me know if you think I missed something thing please.

  Read the article

• Can't Move Windows to 2nd Monitor without Left Mouse and Cntl Key

  - by John C

  I have 2 very frustrating problems that maybe someone can help me with: I have 2 monitors (different sizes and resolutions) setup with the "Extended" monitor Win7 setup. My problem is this = I can not "move" a window from my Primary Monitor (larger and higher resolution on right side in front of me) to my Secondary 2nd monitor (smaller and lower resolution) with just selecting the title bar with the left mouse button and dragging it to the left. Windows 7 "snaps" it back to the left Primary Monitor when the window is physically in the 2nd window area as I'm holding the left mouse button. I can prevent this problem - by holding down the Cntl Key with the Left Mouse button, but this is extremely annoying to me. Also I typically "lose" focus if I try typing input on the 2nd monitor. Typing is erratic with regard to keystroke accuracy from my keyboard translated into input on the 2nd screen. No problem with typing input on the primary left monitor. I find this extremely annoying in Windows 7 and turning off the "snap" feature via the Control panel does NOT work for me. Win7 stubbornly refuses to move my selected window to my 2nd monitor without me "forcing" Win7 to do this with the Cntrl Key. Please tell me this is not a Win7 feature. Also on my system - Windows Key + Shift, Left arrow Key (pressed together) or the same combo with The Right arrow Key - don't do anything whatsoever. Widows Key with "+" however does maximize current window across both monitors, and I can "restore" it with Windows Key and "-" back to original monitor and size. I have tried various solutions including changing the resolutions of one or both of my monitors and sometimes "temporarily helps" but reverts back to the problem. Also if I swap the logical (not physical) layout so that I tell Win7 the monitors are setup in a reserved situation (Large monitor on the left, and small on the right) - this also sometimes helps for awhile - and is very strange and awkward to work with "backwards". But all of these solutions stop working. The only solution that consistently works for "moving" the screens is to hold the Cntrl Key down as I'm moving window with the left mouse selected on the title bar. Even that however, doesn't prevent the loss of typing focus for me on the 2nd monitor - while at the same time the typing on the 1st monitor is fine. Any help on moving my window screens from one monitor on my 2nd monitor without having to press the Cntrl key while holding down my left mouse button with be appreciated. Also any help on gaining typing "focus" into my 2nd screen with be helpful too. Thanks - John

  Read the article

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• How do I create a Windows 7 USB installer with preinstalled software?

  - by Marcel

  I was wondering if it was possible to make a bootlable image of a Windows 7 Pro OEM Installation CD that I have and put it on an USB stick for faster/easier installation. I am asking because we have a couple of PC´s where I´d have to install the OS using the same key (MAK). Also is it possible to kind of populate that image with software that would have to be installed anyways on all machines (like Chrome, Outlook, etc)? It would be really helpful to just install a Windows 7 image with customized software already installed. I would just make an image of an OS and use that, but the hardware of the machines differ.

  Read the article

• Non-Windows, non-Unix-like OS's?

  - by dsimcha

  Since most operating systems I've heard of besides Windows seem to derive their heritage from Unix, I've been curious whether any OS's with the following characteristics exist: Not generally considered Unix-like, i.e. wasn't designed with Unix compatibility as a primary goal, doesn't use X11 as its default GUI in the most common distributions, doesn't support Unix commands by default, etc. Not in the Windows NT family. Is a modern production operating system, not a purely legacy operating system, a research/hobby project or an OS that's still in an alpha state. Is targeted at commodity x86/x64 PC hardware.

  Read the article

• Moving mails from SBS 2008 to SBS 2011

  - by starchx

  we are going to upgrade server from SBS 2008 to a new hardware server with SBS 2011. Due to non-experience in Server Migration (eg, answer file), we have decided to choose Clean Install. We have 12 users so that's not too bad. The most challenge problem is to move over all the emails for each user, some user have 5GB inbox. The one method I know is to login to each user account and export the emails to PST file using Outlook 2007. Then connect to new SBS 2011 and import the PST into new inbox. Do we have any other better/quicker ways? Thanks

  Read the article

• How to solve my black screen at boot?

  - by Juanillo

  I've got a friend with a weird problem. When he starts his computer the screen is completely black until the computer is completely started. So the screen is black until it suddenly shows the Windows desktop. He said that this is happening since a technical service repaired his computer, but that repair is not now in warranty. Recently the computer stopped working, but as the screen is black he cannot access to BIOS or start in safe mode (by pressing F8). When he inserts the Windows Vista DVD the system doesn't boot from DVD (it mustn't be configured in this way in the BIOS). Maybe there´s a problem with the hardware (maybe the graphic card)? Can anyone explain a reason why the screen is black during start-up? Any idea of what to do with the computer to restore it?

  Read the article

• Is there no such thing as a Gigabit switch?

  - by Torben Gundtofte-Bruun

  According to the manufacturer specification, even my rather plain desktop computer has "Gigabit Ethernet". So when I want to copy large files over the LAN (not Internet) it would make sense to have a gigabit switch. I'm searching eBay for a gigabit switch for a planned home network upgrade. The products I find are all labeled "gigabit" but they all have 24 x 10/100Mbit autosensing ports and sometimes 2 x 10/100/1000Mbit autosensing ports. It was my understanding that 10/100 is ancient and that modern computers have network interfaces that work with 1000Mbit, so it would make sense to get a switch that has 24 x 1000Mbit ports. Did I misunderstand, or are sellers (deliberately?) mislabeling older hardware? (Let's not dive into wired vs. wireless networks and how "N" wireless is fast. You'd be right, but not answering the question.)

  Read the article

• XenServer/Center: Shared SRs for hosts not in same pool?

  - by 3molo

  I would like to use the same SRs on XenServer hosts that are not able to be part of the same pool (because of not having the exact same cpu feature set, if I understand it correctly) in order to share templates, being able to (manually) start a host on another node, backing up running hosts on other hardware etc etc. The technology for SR can be any of iSCSI, NFS or CIFS, iSCSI would obviously be preferred. Trying to add an iSCSI volume renders a "This LUN is already in use as SR iSCSI - Shared Storage on pool xxxxxx.". Adding a NFS share on one XS host, creating a template there and then checking another XS host reveals they don't agree on used space etc. Coming from a vSphere world this is quite baffling, but if these are limitations then I will have to rethink some of the concepts for this low budget project.

  Read the article

• Where does linux look for shared libs?

  - by EsbenP

  I am trying to get the ar command on an embedded ARM computer running linux. I want to install debian and openjdk. It is a headless system. This is a custom linux distribution provided by the hardware manufacturer. The debian installer is missing the ar command so i tried copying the binaries from the debian package, but when running ar I get error while loading shared libraries: libbfd-2.18.0-multiarch.20080103.so: cannot open shared object file: No such file or directory libbfd is also in the package. I tried linking it to /lib and /usr/lib but I get the same message when running. What is the best way to get debian and ar on a custom linux distro?

  Read the article

• MSTSC Not working, disconnects shortly after connecting

  - by F4r-20

  I'm currently having a problem connecting remotely to a server. It is a brand new build Windows 2008 R2, remote users are enabled. I'm trying to connect from a Windows 7 machine. Everytime I remotely connect to the server it will stay connected for a matter of seconds (maybe 3-5) and then disconnect and I get the standard old cannot connect and list of reasons it could be. Then I cannot connect again and get this prompt until I restart the server. As soon as it's finished restarting, it happens all over again. The network and hardware configuration between the two machines is completely reliable. Does anybody know what else I could try? Thanks.

  Read the article

• Debian Linux server hangs after a week or so

  - by Alex Flo

  I have 2 Debian Linux 6.0.4 servers that have a strange behaviour: after 5-7-10 days they hang. By this I mean the servers need to be restarted and before that ping won't answer. I've been struggling with this problem for a couple of months now and here's some thoughts/what I tried without being able to solve the problem. I changed the RAM on a server. Being 2 different servers I doubt that it could be something related to hardware as a 3rd identical server won't have this problem. I logged the server load and when it crashes the load is fine (quite low) I cannot find anything in the server logs, logs are fine till the server freezes. I don't have access to console unfortunately. While I have years of admin experience I have never encountered such an issue and right now I have no idea where else to investigate. If you have an idea of what I could try in order to fix the problem please share it with me:-)

  Read the article

< Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >