Search Results

Search found 7555 results on 303 pages for 'installing'.

Page 220/303 | < Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >

• Cannot use second display with 12.04 and Intel 2000/3000

  - by Carolyn Marenger

  I am unable to get anything to display on my second monitor, or even get the system to recognize that there is a second screen. I am running Ubuntu 12.04 on a Gigabyte GA-H61M-S2PV, revision 2.0 box. The integrated chipset is an Intel 2000/3000, and there are both a D-Dub and a DVI-D display ports on the MB. This is the first operating system I have installed on this system. I have a second monitor plugged into the DVI-D port via a DVI-D to D-Sub adapter. I cannot verify that the motherboard or adapter were/are working, short of installing windows to test the theory. When I go into the "System Settings - Displays" control window, it shows one display. I have rebooted with the second monitor attached, and I have perused the BIOS settings in case it might have been disabled. So far, I have had no indication that the second monitor is recognized, not even a flicker at power on. If I swap monitors and cables between the DVI-D and D-Dub ports, the other monitor lights up, so I know the monitor and video cable are not the issue. Any suggestions would be appreciated. Thanks, Carolyn

  Read the article

• IRQ Conflicts Causing Video Card and Boot Problems?

  - by sanpatricio

  tl;dr - I have 4 devices sharing 1 IRQ. Is this bad and how do I tell the BIOS to stop it? Background: I have an old Dell GX280 dual Pentium 4 that I (semi) resurrected last weekend with an installation of Ubuntu 12.04. Everything was going fine the first several hours until a problem that plagued me when WinXP was on that machine happened -- it froze. Completely froze. None of the myriad of ways I have found here on askubuntu helped me to regain control except a long-press of the power button to shut it off. Clearly, this wasn't a software/WinXP issue. After much googling, I found that hardware conflicts can often cause this sort of total lock-up and with all the odd blocks of yellow and flecks of color showing on my screen (both WinXP and Ubuntu) I figured my old GeForce 7600 was failing and causing me these odd issues. (A good canned-air dusting of the entire interior fixed the color fleck problem) Again, through much googling and numerous answers found on askubuntu, I somehow stumbled my way onto the lshw command. After going through it, line by line, I found that I have four devices sharing IRQ 16: eth0, wlan0, ide0 (DVD-RW), and my video card. In hindsight, I can recall weird instances of my Ethernet connection to another computer not working when I thought it should. I never full troubleshot those issues so it could be a coincidence. The other thing that has been plaguing me since installing Ubuntu (wasn't there during WinXP) has been periodic moments of my monitor getting no signal from Ubuntu during boot. The first couple days, it would disappear after the Dell boot screen and reappear at Ubuntu login. Now, it disappears after the Dell boot screen and doesn't return at all -- I have to hit F12 where I can load a safe mode version of Ubuntu and get more details like dmesg and lsdev. I also ran memtest86 overnight and woke up to zero errors, so failing RAM is out. Where do I go from here?

  Read the article

• Install on Acer Aspire 4752

  - by user216962

  I am at my wits end with this computer. I bought and Acer Aspire 4752 with a fully loaded version of Windows 7 on it. I prefer Ubuntu so I began to install 14.04 from USB. Got the error: [Errno 5] Input/output error This is often due to a faulty CD/DVD disk or drive, or a faulty hard disk. It may help to clean the CD/DVD, to burn the CD/DVD at a lower speed, to clean the CD/DVD drive lens (cleaning kits are often available from electronics suppliers), to check whether the hard disk is old and in need of replacement, or to move the system to a cooler environment. So I tried a different USB stick, same error. Tried different versions of Ubuntu, got the same error. I've used startup disk creator and Unetbootin to make start USB boot devices. I can boot with the USB drive and run Ubuntu that way. I even checked the hard drive using the tools in Ubuntu. Everything was fine, except it said the hard drive was hot. I tried a different hard drive. Got same error above. I ran a test with mem86, everything was fine. No matter what I do, using the USB gives me the Errno5 error. I then switched to using DVDs. Now I keep getting an uncompression error when installing Ubuntu 14.04 or 12.04. I can't figure out for the life of me why I get nothing but errors. Can anyone help?

  Read the article

• Pandaboard crash on startup or freeze after minutes

  - by Meach

  I just received my Pandaboard ES (rev B) and I am having trouble after installing ubuntu-omap4-addons. Once I copied the image ubuntu-12.04-preinstalled-desktop-armhf+omap4.img on my sd card and boot the pandaboard with it, I run the following commands: sudo add-apt-repository ppa:tiomap-dev/release sudo apt-get update sudo apt-get dist-upgrade sudo apt-get install ubuntu-omap4-extras At the end of the installation of ubuntu-omap4-extras, Ubuntu tells me that a problem occurs when the console displays: ldconfig deferred processing now taking place Clicking on "report the problem" tell me that the problem concerns pvr-omap4-dkms. I read somewhere that this can happen and it is better to reinstall pvr-omap4-dkms. Which I am doing by running: sudo apt-get install --reinstall pvr-omap4-dkms I reboot. Then the board has sometimes difficulties to start Ubuntu: it freezes during the loading page, only action I can do is unplugging the board to start it again. Some other times, Ubuntu load successfully but then freeze at another random time, in the range 20 - 40 minutes. I searched on internet for similar bug and found this: https://bugs.launchpad.net/ubuntu/+source/linux-ti-omap4/+bug/971091 So I typed this in: update-rc.d ondemand disable apt-get -y install cpufrequtils echo 'ENABLE="true" GOVERNOR="performance" MAX_SPEED="0" MIN_SPEED="0"' > /etc/default/cpufrequtils cpufreq-set -r -g performance reboot But it doesn't seems to fix the bug. Another detail: on startup, before the loading screen of Ubuntu (when there is the two penguins displayed :)), it shows this: [0.297271] CPU1: Unknown IPI message 0x1 [0.308990] omap_hwmod: mcpdm: _wait_target_ready error: -16 [0.354705] omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [0.354766] omap_hwmod_mux_init: Could not allocate device mux entry [2.107086] thermal_get_slope:Getting slope is not supported for domain gpu [2.107116] thermal_get_offset:Getting offset is not supported for domain gpu [2.107299] stm_fw: vendor driver stm_ti1.0 registered [8.725555] OMAPRPC: Registration of OMAPRPC rpmsg service returned 0! debug=0 Any idea what can be wrong? I am not that good with Ubuntu so any help will be appreciated. Cheers! Meach

  Read the article

• Sandcastle Help File Builder - October 2010 release

  - by TATWORTH

  At http://shfb.codeplex.com/releases/view/92191, the latest Sandcastle has been released. I am pleased to say that it incorporates the generic version of a fix, I originated that allows projects including Crystal Reports to be documented.Here is the relevant passage from the help file:"The default configuration for MRefBuilder has been updated to ignore the Crystal Reports licensing assembly (BusinessObjects.Licensing.KeycodeDecoder) if it fails to get resolved. This assembly does not appear to be available and ignoring it prevents projects that include Crystal Reports assemblies from failing and being unbuildable."There are many other fixes. Here are the release notes:IMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog.This release supports the Sandcastle October 2012 Release (v2.7.1.0). It includes full support for generating, installing, and removing MS Help Viewer files. This new release supports Visual Studio 2010 and 2012 solutions and projects as documentation sources, and adds support for projects targeting the .NET 4.5 Framework, .NET Portable Library 4.5, and .NET for Windows Store Apps.See the Sandcastle 2.7.1.0 Release Notes for details on all of the changes made to the underlying Sandcastle tools and presentation styles.This release uses the Sandcastle Guided Installation package. Download and extract to a folder and then runSandcastleInstaller.exe to run the guided installation of Sandcastle, the various extra items, the Sandcastle Help File Builder core components, and the Visual Studio extension package.What's IncludedHelp 1 compiler check and instructions on where to download it and how to install it if neededHelp 2 compiler check and instructions on where to download it and how to install it if neededSandcastle October 2012 2.7.1.0An option to install the MAML schemas in Visual Studio to provide IntelliSense for MAML topicsSandcastle Help File Builder 1.9.5.0SHFB Visual Studio Extension PackageFor more information about the Visual Studio extension package, see the Visual Studio Package help file topic.

  Read the article

• Dual monitor setup can cause boot problem?

  - by kriszpontaz

  I have a two monitor setup, one 22" (1680x1050 res., 16:10) and another 19" (1280x1024 res. 5:4). I've installed ubuntu 11.10 beta2 x86, and the installation worked fine, the system boot was successful. I've upgraded ubuntu from the main server, and after restart, booting with the kernel 3.0.0-13, my system hangs up with a purple screen, and than nothing happens (the system boots successful with the kernel image 3.0.0-8). Nvidia current drivers not installed, but if i install it, the situation is the same. I have an Nvidia 9600GT installed. I tried to boot with one screen attached, I've tried each port, but no luck at all. With kernel image 3.0.0-8 the system successfully boots with each display attached, but the farther kernels (3.0.0-11; 3.0.0-12; ect.) all freezes, even one display, or multiple attached. I have two systems with ubuntu installed, and the other (with Ati HD 2400XT, latest closed drivers) don't have any issues like this, I wrote about. Update: The problem solved by reinstalling the operatin system, without automatically installing updates during install, with only one monitor attached. After completing installation, and clean reboot, i've installed closed nVidia drivers. After all, i found it's safe to connect another monitor to the system, it's not causing any problems. Probably the situation stays like this.

  Read the article

• foreign-architecture

  - by speedy-MACHO

  Always when I install something, I get the following error multiple times: Unknown configuration key 'foreign-architecture' found in your 'dpkg' configuration files. This warning will become a hard error at a later date, so please remove the offending configuration options and replace them with 'dpkg --add-architecture' invocations at the command line. When I try dpkg --add-architecture I get: Unknown configuration key `foreign-architecture' found in your `dpkg' configuration files. This warning will become a hard error at a later date, so please remove the offending configuration options and replace them with `dpkg --add-architecture' invocations at the command line. dpkg: error: --add-architecture takes one argument Type dpkg --help for help about installing and deinstalling packages [*]; Use `dselect' or `aptitude' for user-friendly package management; Type dpkg -Dhelp for a list of dpkg debug flag values; Type dpkg --force-help for a list of forcing options; Type dpkg-deb --help for help about manipulating *.deb files; Options marked [*] produce a lot of output - pipe it through `less' or `more' ! I've no problems yet, but since it says This warning will become a hard error at a later date I better do something about this. When I search 'foreign-architecture', I find an empty file, containing not a single byte. I somehow can't delete that file. Please help, it's a kind of creapy...

  Read the article

• USB mouse pointer only moving horizontally on macbook 6.2 with 12.04

  - by Glyn Normington

  After installing Ubuntu 12.04 on a macbook pro 6.2, the touchpad and external USB mouse worked perfectly. After rebooting I can't get either touchpad or external USB mouse to work. Sometimes no mouse pointer is visible, but more often I can only move the mouse pointer horizontally five sixths of the way across the display (from the top left). I have uninstalled mouseemu. xinput list shows the USB mouse. xinput query-state for the USB mouse shows the following: ButtonClass button[1]=up ... button[16]=up ValuatorClass Mode=Relative Proximity=In valuator[0]=480 valuator[1]=2400 valuator[2]=0 valuator[3]=3 and re-issuing this command with the pointer at its right hand extreme displays the same except for: valuator[0]=1679 So the valuator[0] seems to be the x-coordinate of the pointer and the range of motion 480-1679 is indeed about five sixths of the display width (1440). valuator[1] is suspiciously large given the display height is 900. Perhaps this is a side-effect of having previously been using a dual monitor (although booting with that monitor connected does not help). There are other entries listed under xinput list: Virtual core XTEST pointer which seems stuck at position (840,1050). bcm5974 which seems stuck at position (837,6700). Removing the bcm5974 module using rmmod disables the toucpad as expected but does not fix the USB mouse problem. After adding the module back, it is stuck at position (840,1050) instead of (837,6700). /etc/X11/xorg.conf was generated by nvidia-settings and contains: Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "ZAxisMapping" "4 5" although I don't know how plausible these settings are. Any suggestions?

  Read the article

• How to get Visual Studio 2010 Express Edition on Windows 7

  - by thanigai

  Visual studio 2010 is an amzing release from Microsoft. I have tried the beta 1,2 of Visual Studio 2010 and finally the full version is released. I am also interested in the latest edition of Windows which nothing but our Windows 7. Next to Vista I like this version very much. Out of curiosity I have installed the prebuild version of Windows 7. I tried installing the express edition here and it failed making me disappointed. I tried two or three times and finally I decided to download the trial version of Windows 7. After that I can install the Visual Studio 2010 express edition easily. I have given the link below from where I have downloaded the file. http://www.microsoft.com/express/downloads/ Here the link give is through Web PI Installer. Other option is you can download the ISO image file and burn them to a disc or use a virtual disc This Visual Web developer will provide the Sql Server engine alone. To get a Sql Server Management Studio get from the following link http://www.microsoft.com/express/Database/InstallOptions.aspx That's it all the things necessary for the web application programming is ready. Ah I forget to tell about the Silverlight. Please find the Silverlight 4 latest tools from the below link (WCF RIA services is the main update) http://www.silverlight.net/getstarted/ Silverlight 4 Tools(http://www.microsoft.com/downloads/details.aspx?FamilyID=eff8a0da-0a4d-48e8-8366-6ddf2ecad801&displaylang=en) Expression Blend 4 trial(http://www.microsoft.com/downloads/details.aspx?FamilyID=88484825-1b3c-4e8c-8b14-b05d025e1541&displaylang=en) I think the reader would have enjoyed on how to get these things. Please let me know if you are not clear with any of these things.  Thanks, Thani

  Read the article

• Is chroot the right choice for my use case?

  - by Anthony

  Backstory: I am working on setting up a MineCraft server and want to allow admins to have ssh access to the MineCraft server console and appropriate mc server files, but not the whole system. The console provided by the minecraft server is only available to the user that launched the process. In addition, the admins will need terminal access to some basic cli tools such as wget, cp, mv, rm, and a text editor. Plan: I have already setup the ssh aspect of things, requiring pre-shared keys and whatnot. Setup a jailed environment in which all user activity will be contained. Setup user accounts. - The first user account will be the minecraft user. The minecraft user will start the MC server in a multiuser screen session and allow the other admins to attach to it. - Subsequent users should have their own /home directory for normal usage. Setup acl for the appropriate files to allow each user to edit the mc server files. No one will be doing system updates, nor will anyone be installing any programs, so I'll be the only user with sudo. The Issues: I don't want the ssh users to have access to the whole system. Users will still need to use wget or curl to update the mc server files. Is chroot the right tool for this use case, or is there something more appropriate for the job? I have no experience setting up a chroot environment and have found several tools to aid in this process. Jailkit seems to be the most robust, but it's not in the standard repos.

  Read the article

• How can I get my monitor's maximum resolution without the proprietary AMD graphic driver installed?

  - by Venki

  I am using Ubuntu 14.04. I have an AMD Radeon 5570 HD graphic card. Actually, the default open source REDWOOD drivers aren't allowing me to choose my monitor's maximum screen resolution(which is 1366 x 768). I just have two resolutions displayed which are 1024x768 and 800x600 . If I give the command : xrandr -s 1366x768 then the output is: Size 1366x768 not found in available modes So just for the sake of getting 1366x768 resolution I am forced to install the proprietary graphic driver that AMD gives me from its site. But if I install it(which itself is quite a problem-prone process), I undergo a lot of 'inconvenience'. Sometimes after an OS update, the driver crashes unity. Then I will have to uninstall that driver from a tty and google around for a solution. Also I encounter screen tearing problems occasionally. In addition I also cant see my login screen(See this question which states this particular problem). The main problem is AMD does not update its driver as quick as Ubuntu updates its OS. This is quite irritating. So, I want the maximum resolution(and performance) that my graphics card and monitor can give me without installing the 'problematic' proprietary graphic card driver that AMD gives. Is this possible? Suggestions please. Thanks in advance. PS :- More system specs details:- Intel i3 2100 processor AMD P8H61-M PLUS2 motherboard AMD Radeon 5570 HD graphic card DELL monitor (BTW, Thank you for reading through my elaborate description!)

  Read the article

• Completely unable to install python2.7-dev

  - by gath

  Am totally stuck! Am unable completely to install python2.7-dev on my Ubuntu13.04. I have tried all the tricks mentioned on this site (askubuntu.com) and many other sites on the web but still nothing! Am running Ubuntu 13.04 64bit on a virtualbox, but every time I run sudo apt-get install python2.7-dev, I get the following error; python2.7-dev : Depends: python2.7 (= 2.7.3-0ubuntu3.5) but 2.7.4-2ubuntu3 is to be installed Depends: libpython2.7 (= 2.7.3-0ubuntu3.5) but 2.7.4-2ubuntu3 is to be installed Depends: libexpat1-dev but it is not going to be installed Depends: libssl-dev but it is not going to be installed E: Unable to correct problems, you have held broken packages. I've tried to do apt-get update, but still nothing! I've even tried installing Python2.7 from sources, but still nothing doing! Is there a single package with all the dependencies I can download, that can just install everything (Python2.7-dev) or is there another trick I can use to get the Python-dev headers installed on my machine. Hint: I've noticed when I run sudo apt-get update , somewhere along the updates I've seen some errors; ... Get:1 http://us.archive.ubuntu.com precise-updates Release.gpg [198 B] Ign http://us.archive.ubuntu.com raring Release Ign http://us.archive.ubuntu.com raring-updates Release Ign http://us.archive.ubuntu.com raring-backports Release Ign http://us.archive.ubuntu.com raring-security Release Get:2 http://us.archive.ubuntu.com precise-updates Release [98.7 kB] Err http://extras.ubuntu.com raring/main Sources 404 Not Found Err http://extras.ubuntu.com raring/main amd64 Packages 404 Not Found Err http://extras.ubuntu.com raring/main i386 Packages 404 Not Found Ign http://extras.ubuntu.com raring/main Translation-en_US Ign http://extras.ubuntu.com raring/main Translation-en ... On my precise-updates.list file is a single entry; deb http://us.archive.ubuntu.com/ubuntu/ precise-updates main restricted I don't know if that might help Help! Paul

  Read the article

• Lost WiFi after 12.10 upgrade

  - by Steven Guillory

  I received my new Dell Vostro 2420 last week, and just got around to upgrading from 11.10 to 12.10. Unfortunately, like many others (after researching the issue), I no longer have WiFi. I have tried every sudo command given that worked for others, and still can't get my wireless to function. I am new to Linux, so any and all help is appreciated. Thanks in advance! Edit: I can connect via ethernet, just not via wifi. As a matter of fact, when I use Fn + F2 to turn on wifi, only my bluetooth comes on. lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 07:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) This is what I am getting... dpkg: error: --install needs at least one package archive file argument Type dpkg --help for help about installing and deinstalling packages [*]; Use dselect or aptitude for user-friendly package management; Type dpkg -Dhelp for a list of dpkg debug flag values; Type dpkg --force-help for a list of forcing options; Type dpkg-deb --help for help about manipulating *.deb files; Options marked [*] produce a lot of output - pipe it through less or more !

  Read the article

• eSTEP TechCast - December 2012

  - by uwes

  Dear partner, we are pleased to announce our next eSTEP TechCast on Thursday 6th of December and would be happy if you could join. Please see below the details for the next TechCast.Date and time:Thursday, 06. December 2012, 11:00 - 12:00 GMT (12:00 - 13:00 CET; 15:00 - 16:00 GST) Title: Innovations with Oracle Solaris Cluster 4 Abstract:Oracle Solaris Cluster 4.0 is the version of Solaris Cluster that runs with Oracle Solaris 11. In this webcast we will focus at the integration of the cluster software with the IPS packaging system of Solaris 11, which makes installing and updating the software much easier and much more reliable, especially with virtualization technologies involved. Our webcast will also reflect new versions of Oracle Solaris Cluster if they will be announced in the meantime. Target audience: Tech Presales Speaker: Hartmut Streppel Call Info:Call-in-toll-free number: 08006948154 (United Kingdom)Call-in-toll-free number: +44-2081181001 (United Kingdom) Show global numbers Conference Code: 803 594 3Security Passcode: 9876Webex Info (Oracle Web Conference) Meeting Number: 255 760 510Meeting Password: tech2011 Playback / Recording / Archive: The webcasts will be recorded and will be available shortly after the event in the eSTEP portal under the Events tab, where you could find also material from already delivered eSTEP TechCasts. Use your email-adress and PIN: eSTEP_2011 to get access. Feel free to have a look. We are happy to get your comments and feedback. Thanks and best regards, Partner HW Enablement EMEA

  Read the article

• I can't enable extra effects in Ubuntu 10.10. Please help?

  - by jasoncruz98

  I installed Ubuntu 10.10 alongside Ubuntu 11.10 to use an older version of Compiz. On Ubuntu 11.10, Compiz was enabled by default and I didn't need to use any graphics driver to enjoy the effects. All I had to do was install CompizConfig Settings Manager and enable those extra effects. That was Compiz 0.9.6. Now, after installing Ubuntu 10.10, when I first logged in, the graphics were slow. When I dragged a window from one end of the screen to the other, the whole screen would blur up and pixelate and it would be very laggy. I tried going to System Preference Appearance and selecting Extra effects on the Visual effects tab, but all I got was "Desktop effects could not be enabled". I don't know whether I should install the Additional drivers (proprietary) because my Internet is slow and it would take a long time. Furthermore, in Ubuntu 11.10, after I installed the proprietary graphics driver, I immediately went into fallback mode and wasn't even offered an option to set my desktop session to Ubuntu 3D. I didn't need the driver to run Compiz in Ubuntu 11.10, it just ran so smoothly. But in Ubuntu 10.10, everything is so laggy. Should I install the ATI/AMD Proprietary FGLRX Graphics Driver for Ubuntu 10.10 to enable extra effects? Or is there something else wrong with my system? Here is the output of lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation Sandy Bridge Integrated Graphics Controller [8086:0116] (rev 09) 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Device [1002:6760] Here is the output of the same command, but in Ubuntu 11.10 (in this case the one which is correct, because I don't have the Sandy Bridge Integrated graphics controller) 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc NI Seymour [AMD Radeon HD 6470M] [1002:6760]

  Read the article

• Lenovo Y460 Intel Driver Secondary Display Flickering

  - by ultimatebuster

  This is a part of the massive dump of problems I'm encountering with my Lenovo Y460 and Ubuntu. Problem: ATI PowerXpress doesn't really work. Doesn't work as I have to use the open source driver with hacks. Turned off ATI card at boot Details on how I accomplished that: http://ubuntuforums.org/showthread.php?p=10955831#post10955831 Installing the ATI drivers results in a failure of the intel drivers to work with Ubuntu Class (all animations have to turned off). Anyway to fix this problem to allow switchable graphics to work? The problem above has been fixed by FGLRX (Catalyst 11.6) is it compatible with kernel 2.6.39? However, there's another issue. If I connect my secondary monitor (VGA 17'') while using the Intel driver, I would not be able to use that screen as there's flickering and tearing, making the screen blurry and usable. Here's the fglrxinfo: $ fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Tungsten Graphics, Inc OpenGL renderer string: Mesa DRI Intel(R) Ironlake Mobile GEM 20100330 DEVELOPMENT OpenGL version string: 1.4 (2.1 Mesa 7.10.2) Any fixes for that? Potential related bug report on launchpad: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/750259 However I can't confirm because the video showing that is much more dramatic than what I have, mine are tiny flickering that won't be captured by video cameras as I've tried, but enough to make it blurry for humans.

  Read the article

• Grub2 won't detect Ubuntu 11.10 OS after reinstalling Win XP hal.dll.

  - by yoopian

  Hi I'm an Ubuntu newbie here. I've installed ubuntu 11.10 to dual boot on a single HDD. I did a manual partition and basically forgot all the on what sda my /boot partition is. My installation worked out just fine and I tried to install updates with it. After a while I when I wanted to boot to windows it showed that I was missing a "hal.dll" file. I've fixed this problem using the windows resource CD but then after booting up my PC it went straight to Windows XP. I've tried to manually reinstall Grub2 using a Live CD/USB and it worked but I think I have installed in on a different "sda#" (sda5 to be exact) because even though Grub2 loads when I boot my PC, only windows XP shows up as my OS and Ubuntu 11.10 is missing. Now, I've tried installing boot-repair to solve my problems using Live CD/USB. Boot-repair tells me that boot configuration was successful but then a basic grub interface shows up (the black one with a command line grub showing up. Now I can't even boot to Windows XP. Any help would be really appreciated. BTW here's the notes from boot repair that I was asked to save: http://paste.ubuntu.com/890228/ As you can see there are boot files on sda5 and sda7. I think that's the core problem that I have right now. Thanks in advance!

  Read the article

• Dualboot Asus n56v (ubuntu / win 7 x64) - ubuntu doesn't detect partition table made by windows

  - by user76439

  I have an Asus n56v and I've got troubles installing Ubuntu 12.04 x64. I already have installed Windows 7 x64! The hard drive is: Hitachi HTS547575A9E384 My problem: The installation program doesn't recognize the already existing partitions and is offering only options where there are partitions. Can someone help me out? Is this an ACPI/IDE conflict, missing driver or conflict with Windows 7? (I'm not an expert on Linux, only working sometimes with it.) I now tried out some options concerning EFI with a GTP-table. Everything worked but I wasn't able to fix a dual boot (Windows boot loader) nor with GRUB2. The laptop is still having a BIOS, but is able to boot DVDs/CDs in EFI-mode. Now I try to avoid EFI and GTP using the old windows MBR style. I reinstalled Windows, so far no problem. When I want to try to install Ubuntu, it doesn't detect the already existing partition table. It is just showing me an empty space for the whole disk. Other threads like Ubuntu 12.04 does not see windows already install on my computer (dual installation) don't help me out. os-prober shows me a correct result. I don't know how to deal with gdisk as shown in Installer doesn't detect existing partition table/windows 7 partition. I have 750GB for the whole disk. I'm using: 90GB for Windows reserved partition + system partition, 500GB for data and the rest should be for SWAP and linux-system. How can I make Ubuntu detect the partition table?

  Read the article

• Accessing second hard drive

  - by Jonathan

  So I recently installed Ubuntu 10.10 64-bit on my computer. I installed it on my 60gb SSD hard drive, and in the installation it never acknowledged the existence of my second hard drive. The hard drive that I keep all my files on, and which I want to make my home folder if I can, is a Western Digital Caviar Black 1TB SATA 6Gb/s 64MB cache (WD1002FAEX). I've read the following: https://help.ubuntu.com/community/Mount but honestly cannot work out how to access the hard drive from my Ubuntu installation. I did have Windows 7 64-bit prior to installing Ubuntu. I have backed up all the files on the hard drive, but if I could just access them straight off that would be super cool. Does anyone know how I can use the second hard drive? Thank you for your help EDIT: The following directories are currently in my /dev/ folder: ati/, block/, bsg/, bus/, char/, cpu/, isk/, input/, mapper/, net/, pktcdvd/, pts/, shm/, snd/, and usb/ EDIT: Result from sudo fdisk -l Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d2dfd Device Boot Start End Blocks Id System /dev/sda1 * 1 6994 56174592 83 Linux /dev/sda2 6994 7298 2438145 5 Extended /dev/sda5 6994 7298 2438144 82 Linux swap / Solaris @djeykib So very close to fixing it.. unfortunately on the last command you gave it says this: $ sudo apt-get install linux-lts-backport-natty Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-lts-backport-natty Checking on http://www.ubuntuupdates.org/ppas reveals that it is only available for 10.04. Looks like I'll have to unplug and re-plug hardware if I want it working still :(

  Read the article

• Install Ubuntu in UEFI mode (unable to boot from USB)

  - by Adele

  I recently bought a Dell Inspiron 15R SE with Windows 8 (64 bit) pre-installed (UEFI supported). I want to install Ubuntu in dual boot with Windows 8. I tried to follow all instruction here : https://help.ubuntu.com/community/UEFI And here : Installing Ubuntu on a Pre-Installed Windows 8 (64-bit) System (UEFI Supported) So, I set Secure Boot to "off" into BIOS and I disable Fast Startup as described here : http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html I created a bootable USB key for Ubuntu (Ubuntu 13.10 64bits international Edition) with Unetbootin. The problem is I am unable to boot from the USB key. The computer tries to boot into infinite loop. I also tried to boot from USB with "Legacy Boot" option instead of UEFI. In this case, the computer says there are no bootable devices. Of course, I tried to boot from my USB key on an other computer having normal BIOS and it works perfectly. Have you ideas about what I need to do to be able to boot from USB ? Thanks in advance for your help, Adele

  Read the article

• Error: kernel headers not found. (But they are in place)

  - by Guandalino

  I'm trying to install the Guest Additions in VirtualBox 4.04. Host OS is Ubuntu desktop 11.04 64bit, guest OS is Ubuntu server 11.10 64bit. $ sudo ./VBoxLinuxAdditions.run After some output this line is printed: The headers for the current running kernel were not found. But the headers are installed, at least accordingly to dpkg: $ dpkg --get-selections | grep linux-headers linux-headers-3.0.0-12 install linux-headers-3.0.0-12-server install linux-headers-server install The running kernel is: $ uname -a Linux foobar 3.0.0-12-server #20-Ubuntu SMP Fri Oct 7 16:36:30 UTC 2011 x86_64 x86_64 X86_64 GNU/Linux How do I fix things so that Guest Additions installer is able to find kernel headers? Update: added full output. The headers for the current running kernel were not found. If the module compilation fails then this could be the reason. Building the main Guest Additions module ...done. Building the shared folder support module ...fail! (Look at /var/log/vboxadd-install.log to find out what went wrong) Installing the Window System drivers ...fails! (Could not find the X.Org or XFree86 Window System). I don't care for fail #2, because that's a server and I don't need X server. But I need shared folder support. Some further detail: $ tail /val/log/vboxadd-install.log .......... cc1: some warnings being treated as errors make[2]: *** [/tmp/vbox.0/vfsmod.o] Error 1 make[1]: *** [_module_/tmp/vbox.0] Error 2 make: *** [vboxsf] Error 2

  Read the article

• Never before had a problem with Ubuntu desktop graphical display; Trying to use nvidia GT630

  - by focaccio

  I've been using ubuntu since 9.04 and never had a problem with Ubuntu brining up the desktop graphical user interface. However I am currently not able to see anything graphical past the install screens. I have an Intel DP55KG motherboard and just installed an nvidia gt630 graphics card (zotac), since the old graphics card failed. I can install the server and see text. So I do a apt-get install ubuntu-desktop...or apt-get install kubuntu-desktop...or apt-get install xubuntu desktop, but after the reboot there is no display...its like something is hung up. I tried using the Live quantal dvd and I do see the graphical prompt to try without installing, but after that the screen goes blank. I've tried two monitors and the same thing happens. There is a faint "glow" on the screen and I do not get a "no input signal" from the monitor, so something is happening. I can install an old OEM of XP so I know the video card and motherboard are at least semi functional. Any help is appreciated. Thanks, Greg

  Read the article

• Implementation Specialist OPN Exam for OBI Suite 11g is Now LIVE

  - by Mike.Hallett(at)Oracle-BI&EPM

  The OPN specialisation Exam for implementation consultants of OBI Suite 11g is now live and ready for all partners.  You can now update your specialisation certification to the latest product version 11g for OBI: until recently, the accreditation had examined skills for OBI 10g. For more details see Oracle Business Intelligence Foundation Suite 11g Essentials (1Z1-591) where you can apply for this Oracle Implementation Specialist credential. This exam is primarily intended for consultants that are skilled in implementing solutions based on Oracle Business Intelligence Foundation Suite 11g. The certification covers skills such as: installing OBIEE, building the BI Server metadata repository, building BI dashboards, constructing ad hoc queries, defining security settings and configuring and managing cache files. The exam targets the intermediate-level implementation team member. Up-to-date training and field experience are recommended.   Also Note the New OPN on-line Sales & Pre-sales Assessment Tests are available @ Oracle Business Intelligence Foundation Suite 11g Sales Specialist Oracle Business Intelligence Foundation Suite 11g PreSales Specialist Oracle Business Intelligence Foundation Suite 11g Support Specialist FREE Certification Testing at OpenWorld ·       Are you attending OPN Exchange @ OpenWorld ? Then join us at OPN Specialist Test Fest! October 1st - 4th 2012, Marriott Marquis Hotel :  Pre-register here now!   For More Information OPN Certified Specialist exams OPN Certified Specialist FAQ Enablement 2.0 Get Specialized!

  Read the article

• send music to upnp device from PC

  - by markrich

  I have a new Arcam AirDAC (http://www.arcam.co.uk/products,rSer...ACs,airDAC.htm) attached to my stereo which has upnp support. I would like to send audio from my 14.04 PC to the box itself and to this end installed Rygel upon my system to help but it hasn't. I have created a new sound device in PulseAudioPreferences and selected it from inidcator-sound-switcher but here I become stuck. The sound is heading to the new sound device as the volume can be seen to go up and down from PulseAudioVolumeControl but no sound comes from the stereo downstairs. The problem, as I see it, is the new device has no idea where to send the music as the Arcam hasn't been chosen from any program. So - I installed BubbleUPNP and Plex. My music has been imported into the later and the former can see both the Arcam as a Renderer and the Plex as the Media Server. Installing the BubbleUPNP program on my Android tablet allowed me to send music and all seemed good UNTIL I started playing AIFF and ALAC music and it all stopped. No suitable decoding device. So that scuppered that route. So here I am and stuck. How can I tell Ubuntu to use the Arcam as a renderer to play music through when the albums are played from Rhytmnbox, Tomahawk, Clementine or other? Clementine would be my preferred client as there is a usable remote control program for the tablet. Can anyone help me fix this or advice another way to do what I would like?

  Read the article

• Broadcom Wireless Issues in Lubuntu 14.04

  - by ratxinxaxcage67

  I recently installed Lubuntu 14.04 on my parents' old laptop, and I've been having a super difficult time getting the Broadcom card up and running. I've been following this thread: Installing Broadcom Wireless Drivers ...but I'm still stuck. lspci -vnn | grep Network showed: 06:05.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 02) iwconfig showed: lo no wireless extensions. eth0 no wireless extensions. I've installed b43-firmware-installer and b43-fwcutter and also the linux-firmware-nonfree package. At boot, I keep getting a b43-phy0 error, so I tried sudo rmmod b43, and I got: rmmod: ERROR: Module b43 is not currently loaded I also tried: dmesg | grep b43 [ 17.318405] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4) [ 17.384870] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw [ 18.046777] b43legacy ssb0:0: Direct firmware load failed with error -2 [ 18.046785] b43legacy ssb0:0: Falling back to user helper [ 18.047858] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed. [ 18.047965] b43legacy-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3). I went to url it told me to, but it didn't tell me to do anything I haven't already tried. Any help and/or suggestions would be greatly appreciated!

  Read the article

< Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >